Search Documents

By Ananta L. Yennamani

Blast movement measurement (BMM) transmitters are a practical method to measure three-dimensional (3D) rock movement because of blasting. The BMM transmitters are activated, programmed and installed in specially designed drill holes prior to the blast and the BMM detector locates the transmitters after the blast. The BMM software then calculates and summarizes the 3D movement of each BMM transmitter ball. This information helps to redefine the ore and waste boundaries and enables improved ore and waste selection, resulting in a genuine step change in grade control. The BMM program was carried out at Newmont Mining Corp.?s Phoenix Mine, in northern Nevada near the town of Battle Mountain. The mine is in a historic mining district that contains gold, silver and copper. The geology of the pit consists of different formations made up of sandstone, siltstone, limestone, chert-pebble conglomerate, shale, skarn and quartzite, to name a few. Some of the rock is extremely hard and a powder factor of up to 0.5 kg/t (1 lb/st) is required to get adequate fragmentation to ensure sufficient throughput through the crusher and the mill. The result of using such a high powder factor translates into considerable blast movement and heave. This movement means that the ore/waste digging polygons estimated by the ore control engineer from sampling the initial blast holes will no longer be located in their original posi-tions. The purpose of this project was to test the measurement method and to see if locating the digging polygons in the broken muck pile and excavating to those polygons will improve grade control through the mill. Case studies (Zhang, 1994), (Taylor, 1995), (Gilbride, 1995), (Harris, 1997), (Taylor, 2003), Barrick Goldstrike (Gold-strike Mine, 2008), Ruby Hill Mine (Hilkewich, 2009), (Porcupine Mine, 2005) and (Aguirre, 2010) have shown that, by accounting for the blast movement, there is a potential to increase mineral recovery by as much as 25 percent for individual blasts for only a modest cost increase.

Jan 1, 2011

Provide blasting-resistant, quickly reusable stoppings for large mine openings. Approach Stoppings are assembled using roof-to-bottom panels of brattice held together by Velcro seams that peel open when struck by a strong air blast. How It Works The Velcro seam is designed to open when exposed to forces lower than would normally damage the brattice. When the seams partially open, they relieve the blast air overpressure to prevent damage to the brattice panels and their anchoring devices. A stopping is returned to service by reclosing the Velcro seams. To hang a brattice panel, its top is stapled to a board, and wrapped once or twice around it. That assembly is then attached to the roof with bolts. The length of the board should be a foot less than the width of the panel to allow for the sealing seam on each side of the panel. The boards are installed end-to-end in an approximately straight line across the roof of the mine opening.

Jan 1, 1979

By R. H. Sweetser

AT the Buffalo meeting in October, 1898 (Trans., xxviii., 865), our Secretary, Dr. Raymond, in speaking of the obstacles he had encountered in securing contributions to the Transactions from members in practice, said: "It is the disinclination of many members to communicate incomplete or partial or preliminary results. They are going to write, ' some day,' a thorough and monumental paper; and meanwhile they prefer to communicate nothing. . . . It is the difficulty to which I have just referred that I have encountered in a wide correspondence with members, undertaken for the purpose of securing contributions of fact and opinion concerning the special subject of this discussion. . . . Almost none of them seem to recognize the value of preliminary, incomplete and indecisive reports of practice, as laying the foundation for a thorough inquiry." This remark was made in immediate reference to a discussion concerning blast-furnace tuyeres ; but, notwithstanding this appeal from the Secretary, little has been recorded regarding the distribution, the penetration, and the pressure of the blast at the tuyeres and inside the iron blast-furnace. I am therefore encouraged to contribute the following incomplete and crude observations of the blast-pressure inside the hearth. At the suggestion of J. H. Frantz, the General Manager of the Columbus Iron & Steel Co., a test was made at the East furnace of the company to determine whether there was any difference in blast-pressure at the different tuyeres. The apparatus used for this test was not sensitive enough to give accurate results. It consisted of a small pressure-gauge mounted on a 3/8-in. gas-pipe. A hollow plug, fitting into the peep-hole of the tuyere-cap, prevented the blast from blowing-out during the test. The test-pipe was held in place by means of the handle on the outer end.

Mar 1, 1909

By PHILIPP HARTLIEB, Peter Schimek, Thomas Seidl, Pablo Segarra, José A. Sanchidrián, Juan Navarro

This paper develops a new Blastability Index to assess hole-to-hole fragmentation in bench blasting based on a new Rock Factor exclusively obtained from drill-monitoring data, that can provide an automatic assessment of rock structure, strength, and waste/ore, the effective energy factor of the explosive and the delay time per blasthole.

Feb 1, 2020

By Patrice Favreau

In 1990 the Noranda Technology Centre commenced a project to develop an interactive three-dimensional blast design system using a commerical computer-aided drafting and design package (CADD). The objective was to alleviate the blast engineer from the tedious and time consuming blast layout and design functions normally done by hand. This would allow more time for optimizing blast designs through assessing multiple options. Since several blast design software "tools" already existed at Noranda, the need arose to integrate all the applications into one overall system that shared one common database. The result is BLASTCAD.

Jan 1, 1992

By David Sprott, Patrick Andrieux

In 1990 the Noranda Technology Centre commenced a project to develop an interactive three-dimensional blast design system using a commercial computer-aided drafting and design package (CADD). The objective was to alleviate the blast engineer from the tedious and time consuming blast layout and design functions normally done by hand. This would allow more time for optimizing blast designs through assessing multiple options. Since several blast design software "tools" already existed at Noranda, the need arose to integrate all the applications into one overall system that shared one common database. The result is BLASTCAD.

Jan 1, 1991

By Marcel Laflamme, Sebastián Ibarra‑Gutiérrez

Improvement on controlling the stope limits has enabled the assessment of technical performance in several underground mining operations. Technical performance, integrated to stope geotechnical and geomorphological parameters, constitutes the basis which guides mining engineers in the Mineral Reserves Estimation process. Moreover, there are established definitions to report this information in Canada, incorporated in NI 43–101, which stipulates that “A Mineral Reserve includes diluting materials and allowances for losses that may occur when the material is mined” [1]. However, some loopholes have been identified regarding practical standards followed to specify the way to include and report ore losses when the lost material was blasted and must be left behind unrecovered inside the stope. In fact, general efforts to estimate and quantify the negative effects of operational ore losses only consider under-break ore loss. However, mining engineers frequently confront situations requesting the anticipated closure of a stope. Therefore, reconciliation process should reflect the amount of unrecovered Mineral Reserve. This work presents a discussion of possible practices to integrate adequately operational ore losses consisting of blasted but not recovered material and focuses on how different approaches regarding the material constitution could severely affect the stope technical performance interpretation.

Aug 9, 2021

By George E. Jackson

ANFO, as a blasting agent, is used in large quantities in coal surface mines. It can be purchased on the open market or through reliable suppliers. The blaster in the field must assume that his ANFO is homogeneous, consistent, and nearly identical on a daily basis. A quality control program will enable him to be assured of the correct product. Therefore, the material cost and operational efficiency can be better controlled.

Jan 1, 1978

By John C. Brulia

The IME member companies, the ISEE along with its chapter organizations, the Federal, state and municipal regulatory agencies, and the industry consultants and suppliers have developed safety equipment, provided safety guidelines, promulgated safety-oriented regulations, and conducted safety training for blasting personnel in an effort to reduce explosives-related accidents.

Jan 1, 1994

Blasthole cone samples are used for grade control in most of the iron ore mines of the Pilbara of Western Australia. This method of sampling is straightforward when the target sampling interval matches the mining bench height but is problematic when the blasted bench is 'flitch' mined in two or more passes. Crucially, the sampler needs to decide which part of the blast cone represents the upper and lower flitches to be mined. This sampling selection decision is usually made by assuming a certain proportion represents the subdrill component of a sampling face in a blasthole cone and the two flitches are split equally from the remaining portion. In this study of a West Australian channel iron deposit, sampling experiments were carried out to determine the actual proportions of a sampling face in a blasthole cone by spray painting the blast cones at flitch and subdrill boundaries during the drilling process. Measurements were then taken to assess the differences between assumed sampling face proportions and actual proportions. A set of paired samples was also collected from a number of blastholes with one set using the assumed proportions of each flitch for each sample, while the other set sampled the actual proportions, which were identified from the cone painting process.

Mar 1, 2010

By Betty J. Laswell, Gerald W. Laswell

Rotary drilling in modern open-pit mining is usually considered the lead phase which not only establishes the production rates but frequently limits them. From this viewpoint alone, the drilling phase must be maximized. The drill phase is the step that permits all the other operational phases to function within their design limits. This means that, in most cases, the drill is literally run to destruction to ensure that the shovel will be able to smoothly and consistently load a manageably size muck, the haul trucks can carry a balanced load without having a boulder dropped through the bed, and the crusher can devour constant rock size.

Jan 8, 1978

By G. M. T. Marshall

Plans to bring the Geco Mines property in Manitouwadge, Ont., into production began in 1954. At that time over 12 million tons of copper-zinc ore were indicated in a zone 2700 ft long. A concentrating plant was built to handle 3300 tpd of ore and a production shaft was sunk about 1500 ft. MINE LAYOUT Vertical attitude, width, rake, and competent country rock of a 4-million ton orebody west of the main diabase dike suggested a system of blasthole stopes, undercut with scram drifts connected by a transfer raise system to a crusher on the 1250-ft level and this system was employed. A 42-in. conveyor on this level transfers the ore about 1200 ft to a loading pocket at the No. 1 shaft. The system has a number of advantages: 1) Cost of tramming is eliminated. 2) Rate of extraction from any stope is controlled only by the scraping capacity of the scram. 3) Rate of extraction from the stoping area can be very rapid. Fast extraction makes it possible to cut mining costs for the following reasons: The number of stopes actively producing is kept to an economical minimum; the operating area is concentrated-manpower can be used more effectively; and active life of the stoping block is short, making ground support problems simpler and less costly.

Jan 8, 1959

By H. P. Knudsen

In most open pit gold mines ore waste selection is based on estimates made from blasthole samples. These estimates frequently are biased. While it is true that high grades and "outliers" can induce a bias they may not be the only reason for the persistent bias seen at many mines. This paper focuses on a source of the conditional bias. In this paper it is shown that the poor blasthole sampling can cause a conditional bias in the estimates.

Jan 1, 1991

By K H. Esbensen, K Engström

The conclusion from the debate over the last decade in the mining sector is that, for grade control, reverse circulation (RC) drill sampling gives more reliable results due to less sampling problems than blasthole samples. However, by conducting the latter with well-controlled procedures there still exist fair possibilities to counteract the major blasthole sampling problems and achieve fit-for-purpose representativeness, especially if based on minimal loss of fines. In the present PhD study, extensive replicate experiments and variographic characterisations are conducted to evaluate the performance of manual blasthole (BH) sampling and sectorial segment sampling. The experiments were performed in Luossavaara-Kiirunavaara AB (LKAB)’s Leveäniemi open pit mine in the north of Sweden. The experimental area is an apatite-magnetite iron ore deposit of the Kiruna type, with the demand to exhibit a maximum of local heterogeneity to allow the experiment the largest possible conclusion powers. Gathering and splitting the complete BH drill cutting cones (fines cone, coarse cone) served as an authoritative reference on which to assess the representativity of the two BH sampling methods.Results show that manual BH drill sampling is able to produce samples with an acceptable accuracy and precision if performed properly and with insight. Based on variographic comparison, segment sampling shows similar precision for chemical grades as the manual sampling, while the particle size distributions were more deviating for segment sampling than for manual sampling at the high and low size ranges. Possible reasons for these partly surprising results are discussed.For further investigation of the performance of BH versus RC drill sampling, a second experiment has been planned on a parallel profile. This will result in an unprecedented opportunity for a full variographic comparison between RC and BH sampling, aimed at designing specific, fit-for-purpose sampling procedures as a function of ore quality, cut-off grades and important contaminant levels.CITATION:Engström, K and Esbensen, K H, 2017. Blasthole sampling (replicate and variographic experiments) in LKAB open pit iron ore mines – fit-for-purpose representativity?, Australia, in Proceedings Eighth World Conference on Sampling and Blending , pp 85–96 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By F. Boudreault, M. J. Scobie, J. Szymanski, C. Hendricks

The development of new stoping methods and more effective control over dilution, recovery and fragmentation depends on improved accuracy in blasthole drilling. The mechanisms and factors which control accuracy are poorly understood. Canadian blasthole stoping and the practices adopted for monitoring and controlling drilling accuracy are reviewed. The techniques and problems associated with blashole set-up and trajectory surveying are discussed. Four new blasthole trajectory survey systems are evaluated on the basis of their performance in recent underground trials. Conclusions are drawn as to the technological developments required so that more precise control over drilling accuracy can be achieved.

Jan 12, 1992

By R. H. Brooks

Blasthole stoping methods were introduced at Birchtree Mine as an alternative to the original cut-and-fill and shrinkage stoping methods. The object was to take advantage of the ore structure and conditions, and achieve increased productivity. This paper outlines the design, operation and economics of three areas which utilized blasthole stoping. The 108areafrom 2300 level to 1500level was converted from cut-and-fill to sublevel blasthole stoping based on a block mining-and-filling sequence. The second area, the crown pillar of 110 mechanized cut-and-fill stope below 500 level, was recovered using horizontal rings drilled from raises within the ore zone. The third area, the 83 orebody from 1300 level to 1100 level, used the vertical crater retreat (VCR) method with large-diameter blastholes. Blasthole stoping has increased productivity and improved operating conditions.

Jan 1, 1979

By Louis P. Gignac

The Lac Shortt gold deposit is located in Northwestern Quebec, at some 115 km west of the Opemiska Division and 380 km northeast of the Lac Dufault Division, as shown on Figure 1. Falconbridge's exploration crews drilled the first six holes in the gold-bearing ore zone in 1979. After further diamond drilling from surface in 1980, the decision was taken to carry out an underground exploration program. A three-compartment shaft was sunk to a depth of 340 metres in 1981 and 1982; it was followed by an extensive exploration program, which included 1073 metres of cross-cutting and footwall drifting, 645 metres of ore drifting and 11 200 metres of diamond drilling. The underground work was completed by mid-winter 1983. It was followed by a complete feasibility study of the Lac Shortt Project. After some $Can 14.2 millions in exploration expenditures, the Board of Directors of Corp. Falconbridge Copper approved in July 1983 additional expenditures of $Can 45 millions to bring the Lac Shortt Mine in production at the capacity of 261 000 tonnes per year. Gold price was $US 425 per ounce at the time.

Jan 1, 1985

By VlNTON H. CLARKE

Diamond-drill blasthole sloping has now been used for a long enough time to permit us to discuss fairly its problems from the ore-breaking angle and to attempt to peer into its future. To do this we have gathered information from many properties through questionnaires. The operators have indicated fairly well in their answers what they think of the method. The many variations of methods have by now been fairly well developed, and performance rates and. mining costs are well established at each property. All this can be laid down on paper with fair completeness. Now. knowing all this, what will the future of the method be? To attempt to look into the future of a mining method immediately brings to light many problems and variables. For instance: why were diamond drills used in the first place? What has the cost trend been? In what type of deposit has the method proved most advantageous? What will the future cost of diamonds be? What are the possible substitutes?

Jan 1, 1949

By Peter N. Blakey

The Kidd Creek orebody is a massive, base metal deposit with widths up to 600 feet and a strike length of 2,200 feet. The orebody dips eastwards at 70° to 80° and is amenable to sub-level open stoping. Five distinct zones (Fig.1) based on structural wall rocks and ore type parameters occur within the orebody. These zones are: Zone 1 - Mainly copper stringer ore Zone 2 - Massive pyrite ore Zone 3 - Massive sphalerite and chalcopyrite Zones 4 and 5 - Are banded and variable in nature Compressive strengths vary from zone to zone with an average of 22,000 p.s.i. and highs of 40,000 p.s.i. The mine is developed from a ramp extending from surface to the 1600 foot level and a 24 foot diameter, 3050 foot vertical shaft with main levels at 400 foot intervals. Sub-levels at 100 foot vertical intervals are driven from the ramp. transverse and longitudinal pillars to support the crown pillar left under the open pit. The layout allows an opportunity to enlarge or reduce pillar sizes and also to introduce fill on any horizon should conditions warrant. It also offers a large number of operating stopes spread through the various ore zones giving good ore blending characteristics. All ore from the stopes is handled through drawpoints using Wagner ST8 scooptrams with an average one way haul length of 650 feet.

Jan 1, 1976

By Joseph S. Malesky

As essential as the discovery of coal was to our state of advancement, the discovery and development of explosives marks one of the most important findings in the history of civilization. For this reason explosives are rightfully referred to as the forerunner of progress. Without explosives our vast economic enterprise concerning the mining of coal, copper, iron, aluminum, and various other ores could not function. Explosives are used in all kinds of construction works, in the razing of old buildings, blasting of trenches, driving of tunnels, and in many other instances common to our everyday life. An explosive may be defined as a substance (usually a mixture) that, where flame or shock is applied, yields readily to rapid combustion or oxidation, accompanied by the formation of such relatively large quantities of gases as to produce much violence and pressure which, in turn, react against their surroundings and cause what is termed an explosion. By their very nature the action of explosives is destructive and disruptive of adjacent materials. Decomposition of explosives can occur through deflagration, which is rapid burning or combustion, as in the case of black powder, or through detonation, which is an almost instantaneous disruption, as in the case of dynamites and blasting agents. HISTORY OF BLASTING WITH EXPLOSIVES At one time workmen obtained stone blocks for building by grooving the rock with crude picks, driving wooden wedges into niches in the rock, and pouring water on the wedges; the swelling of the wood forced out the blocks. As late as the 17th century, fires were placed against the face of rock to crack it, and water was sometimes dashed on the heated rock to shatter it by sudden cooling. The progress of our country is synonymous with advancement of the improved manufacture and extended use of explosives. Coal had been

Jan 1, 1973