Search Documents

By Thierry Bernard, Pierre M. Vuillaume, Michel Kiszlo

"In the context of its studies for the trench ministry of the environment and for the French national coal board, INERIS (the French institute for the industrial environment and hazards, formerly CERCHAR) has made a complete critical survey of the methods generally used to reduce the levels of blastingvibrations."

Jan 1, 1996

By Marcello Crispi, Valdir Silva, Juarez Moraes

Companhia Vale do Rio Dote - CVRD is the largest mining company in Brazil and the largest iron ore producer in the world. Serra Geral Mine (SGM) is located at Iron Quadrangle of the State of Minas Gerais, approximately 80 kilometers from Belo Horizonte. Hematite and Itabirite are the two main minerals. A blasting with a spherical charge has been introduced at Serra Geral Mine, an iron ore producer in Brazil, belongs to the CVRD (51%) Kawasaki Steel Corporation (24.5%) others (24.5%), in order to improve fragmentation, as well, load, transportation and crushing productivity. This paper will present the results of a successful blast design with a spherical charge carried out by Serra Geral Mine, the Department of Mining Engineering at Escola de Minas - Federal University of Ouro Preto-UFOP associated to a Blasting Engineering Consultant. The results obtained in the field tests and how it was possible to increase the blast pattern in 53%, which allowed one reduction around 31% in the cost of blasting operation in the Serra Geral Mine, will be discussed in details.

Jan 1, 2002

By Lewis J. Patterson

In the period of time allotted to this paper, an attempt will be made to cover a great deal of territory, figuratively speaking, as far as our experience with ammonium nitrate is concerned. In giving this subject the "broad-brush" treatment, it will be necessary to generalize on the major points which at the same time will permit me to avoid, to a great extent, any involvement in the purely technical and theoretical aspects of blasting. The practice of theorizing before a new idea is tried has practically been discontinued in our organization simply because experience has shown that, almost without exception, theories have fallen aside as some new development takes its place. In regard to blasting, logic and experience seem to have little place in this phase of quarry operations. As the use of low cost blasting agents was introduced in our operating practice, a man who had no previous experience in the field of blasting but with sound knowledge in safety procedures was given the responsibility of supervising the drilling and blasting operations. A total lack of experience is not ordinarily recommended as a prerequisite to assuming the responsibilities of a supervisory position. However, in this case it was obviously a wise decision because there were no pre-conceived ideas as to what techniques would or would not be successful.

Jan 1, 1958

By Walter M. Chapman

The National Lead Company operates its MacI tyre Development at Tahawus, New York for the production of ilmenite and. magnetite. The heavy ore of titanium and iron is mined from the open pit mine at an average rate of 7,000 tons per day, and the development waste is removed at an average rate of 10,000 tons per day. The mine working benches are spaced, at 35-foot vertical intervals, and 6 ½ inch blast holes are drilled 39-feet deep with 18-foot burden and spacing by down-the-hole drills. Waste is loaded with a 6 yeard shovel and ore with 2 ½ yard shovels into 22-ton rear dump trucks. A good account of the history of MacIntyre drilling and. blasting was presented to this assembly two years ago, by F. R. Jones. (1) Most of the blasting since the start of the mine in 1941 was done with 90% gelatin dynamite until 1955, when relatively insensitive canned blasting agents were adopted.. In 1956, 9-inch blast holes drilled with down-the-hole drills. In 1956, also, the first experimental trials of prilled ammonium nitrate fertilizer and fuel oil (hereafter called fertilizer) was made following the lead of Cleveland-Cliffs operations in the Hibbing district. Since that trial did not, as some local skeptics predicted, make grass grown on the bluff, but resulted in a well-broken shot, further tests were conducted in dry holes. I Observations of those tests indicated that the fertilizer did its share of the work. If anything, it produced better fragmentation than the normal load di in neighboring wet holes.

Jan 1, 1958

By Ayman Tawadrous

Cave mining offers a flexible technique to exploit large, low grade, deep ore bodies with low operating costs. It is typically done in either a top down approach; i.e. sublevel caving, or in a bottom up approach; i.e. block or panel caving, to extract ore bodies that may have been previously considered unfeasible to mine. Sublevel Cave (SLC) mining, in particular, is a cave mining method based upon the utilization of gravity of blasted ore while the overlying host rock fractures and caves under induced stresses and gravity. Thereby the caved waste originating from the overlying rock mass fills the temporary void created by ore extraction to achieve a controlled collapse of the roof.

Jan 1, 2015

By Richard J. Mainiero, Marcia L. Harris, James H. Rowland

In the past several years, there have been a number of blasting-related carbon monoxide migration incidents. In each case, there have been some common factors that appear to be related to carbon monoxide migration. Geology, heavy confinement of the blast, close proximity to the affected structure, and open pathways into the affected structure are just a few. Prince William County, VA is an area undergoing a boom in suburban development. In the year 2001, more than 4,050 new homes were constructed within the county.1 In the new housing development located in Bristow, VA, trench blasting was utilized to excavate proposed sewage and utility lines. On November 8, 2002, a trench blast was conducted for the installation of utility lines. Later that evening a carbon monoxide detector alarmed in a nearby house. The gas company and fire department sampled for carbon monoxide and measured 100 ppm and more than 200 ppm on the first floor and in the basement respectively. Subsequent efforts to prevent migration of CO into the nearby homes met with mixed results. The only reliable technique for protecting neighbors from CO appears to be the placement of CO monitors in the homes. The events are presented and discussed.

Jan 1, 2004

By Richard J. Mainiero, Marcia L. Harris, James H. Rowland

In the past several years, there have been a number of blasting-related carbon monoxide migration incidents. In each case, there have been some common factors that appear to be related to carbon monoxide migration. Geology, heavy confinement of the blast, close proximity to the affected structure, and open pathways into the affected structure are just a few. Prince William County, VA is an area undergoing a boom in suburban development. In the year 2001, more than 4,050 new homes were constructed within the county.1 In the new housing development located in Bristow,VA, trench blasting was utilized to excavate proposed sewage and utility lines. On November 8, 2002, a trench blast was conducted for the installation of utility lines. Later that evening a carbon monoxide detector alarmed in a nearby house. The gas company and fire department sampled for carbon monoxide and measured 100 ppm and more than 200 ppm on the first floor and in the basement respectively. Subsequent efforts to prevent migration of CO into the nearby homes met with mixed results. The only reliable technique for protecting neighbors from CO appears to be the placement of CO monitors in the homes. The events are presented and discussed.

By Timothy Stark

At present blasters are strictly liable under tort law for personal injury and property damage caused by ground vibrations and/or air overpressures. The application of strict tort liability to vibration and air overpressure damage has resulted in litigation that has hampered and probably will continue to hamper the blasting industry. There are many case histories in which blasters have been sued for the appearance of cosmetic cracking, some of which have involved frivolous claims and marginal expert testimony (Oriard 1999). This litigation has resulted in additional costs to the blasting and construction industries and the American public because there are usually many plaintiffs involved and each case is usually adjudicated separately instead of under a class-action format. It is proposed herein that blasters not be held liable for vibration or air overpressure damages unless their conduct is proven to be negligent. A number of reasons are presented for raising the legal standard from strict liability to negligence including: (1) improvements in blasting technology that allow blasting to be conducted without substantial risk of damage and if damage does occur it is likely to be cosmetic, (2) establishment of conservative ground vibration and air overpressure damage limits for typical structures, and (3) established industry standards for construction blasting.

Jan 1, 2002

The first of this three part series examines he history and some of the properties and characteristics of explosives. Use of explosives is discussed for underground and surface coal operations—the largest consumers in the mining industry. Part two of the series will deal with explosives use in surface and underground hardrock operations. Part three will discuss explosives transportation, storage, handling, and destruction.

Jan 7, 1981

By Harry Deitzer

Within the industrial marketplace barium sulfate has an established role as a filler or extender pigment for use in a wide array of applications. The focus of this paper is to outline a number of these applications and in each one characterizes those features of barium sulfate which provide value. Following this is a discussion of the process techniques which have been used to develop value from a selected class of barite ores found in southern Missouri. It is appropriate to define some terms which may help in clarifying some concepts as presented. Use of the term barium sulfate refers broadly to the chemical compound BaSO4 Barite will generally refer to the naturally occurring barium sulfate ores and their properties. Barytes, whether bleached or not, will refer to barite ore made suitable for industrial applications.

Jan 1, 1993

By A. D. Rich

The term "bleaching clay" or "bleaching earth," as used in the oil industries, refers to clays that in their natural state, or after chemical or physical activation, have the capacity for adsorbing coloring matter from oil. There are three common types of bleaching clays: fuller's earth, activated clays, and activated bauxite. Fuller's earth, or naturally active clay, is prepared from bentonites (see Chap. 5) that possess natural activity. It is not activated commercially; in fact, earths of this type ordinarily do not respond satisfactorily to acid activation. Fuller's earth is prepared in pulverized as well as granular form for use in the contacting and percolation processes, respectively. Acid-activated clays also are of bentonitic origin. The basic raw clay, however, is of a type that has a very low natural activity but is highly activable by treatment with mineral acid. Commercial acid-activated clays generally possess several times the decolorizing power (bleaching efficiency) of the best quality of fuller's earth. The former are prepared commercially only in the pulverized grade because of the difficulties in obtaining a satisfactory granular product, and hence are used only in the contact process. Activated bauxite is made by heat-treating bauxite ore, which in its natural state has very little natural activity. The commercial product is prepared in granular form for use in the percolation process on petroleum oils. For the most part, bleaching clay is used commercially in the decolorization of animal, vegetable and petroleum oils, fats and waxes. It is applied in two ways: (1) by the percolation method and (2) by the contacting method. Percolation refers to the passage of oil through a bed of granular clay whereas contacting refers to direct agitation of oil and pulverized clay followed by removal of the clay from the oil by filtration. In either case, the decolorizing effect is obtained by intimate contact between the liquid oil and the solid adsorbent. Petroleum oils are treated commercially by either the percolation or the contact process. Animal and vegetable oils are treated by the contact process only. Composition The raw clays from which both fuller's earth and acid-activated clays are prepared are composed of hydrous aluminum silicates containing varying quantities of magnesium, iron, calcium and other elements. These raw materials are usually nonswelling bentonites derived from volcanic ash or lava by weathering and hydrothermal chemical reactions. The bentonites have as their chief mineral constituent montmorillonite, which has the formula [(OH)4Si6A14O20•nH2O], according to Grim. (See Chap. 5, ref. 6, p. 91.) The underlying reasons are not fully known for the natural activity of the fuller's earth type of clay and its usual failure to further activate with mineral acid in contrast to the natural inactivity of the activatable type of clay. However, it may be said that the bentonites that are responsive to the acid-activation treatment generally have not undergone any drastic metamorphism. The chemical composition is not a reliable means of discrimination between a nonactive, a naturally active, and a nonactive but activable clay, therefore it is not possible to forecast the ultimate quality of a clay on the basis of the raw-clay analysis alone. Table 1 gives typical analyses of representative clays of the foregoing classifications.

Jan 1, 1960

By A. D. Rich

THE term "bleaching clay" or "bleaching earth," as used in the oil industries, refers to clays that in their natural state, or after chemical or physical activation, have the capacity for adsorbing coloring matter from oil. There are three common types of bleaching clays: fuller's earth, activated clays, and activated bauxite. Fuller's earth, or naturally active clay, is prepared from bentonites that possess natural activity. It is not activated commercially; in fact, earths of this type ordinarily do not respond satisfactorily to acid activation. Fuller's earth is prepared in pulverized as well as granular form for use in the contacting and percolation processes, respectively. Acid-activated clays also are of bentonitic origin. The basic raw clay, however, is of a type that has a very low natural activity but is highly activable by treatment with mineral acid. Commercial acid-activated clays generally possess several times the decolorizing power (bleaching efficiency) of the best quality of fuller's earth. The former are prepared commercially only in the pulverized grade because of the difficulties in obtaining a satisfactory granular product, and hence are used only in the contact process. Activated bauxite is made by heat-treating bauxite ore, which in its natural state has very little natural activity. The commercial product is prepared in granular form for use in the percolation process on petroleum oils. For the most part, bleaching clay is used commercially in the decolorization of animal, vegetable and petroleum oils, fats and waxes. It is applied in two ways: (1) by the percolation method and (2) by the contacting method. Percolation refers to the passage of oil through a bed of granular clay whereas contacting refers to direct agitation of oil and pulverized clay followed by removal of the clay from the oil by filtration. In either case, the decolorizing effect is obtained by inti-

Jan 1, 1949

By K. F. Unrug

The concept of bolting mine roofs to prevent roof falls was initiated in the 1950's and was quickly accepted by the mining industry because it was inexpensive, effective and convenient. The principle regarding roof bolting were that: a) the loose and fragmented rocks were suspended from or clamped to more competent surrounding rock and b) generally, by clamping several layers of thin and laminated strata, a more competent monolithic beam is created.

Jan 1, 1991

By Reinhard F. Dobner

After a short introduction about the HK's secondary smelter process and explanations concerning the anodes produced the regulation and buffering of bleed will be described and the principles of technology for processing of bleed will be presented. Modernization aspects, especially installation equipment, and the different types of evaporators used will be described in detail. Besides, experience made with acid-resistant materials - stainless steel, enamel, plastics - will be reported. Environmental aspects such as water and air pollution will be outlined briefly and in conclusion the quality of products obtained as well as quality control will be presented.

Jan 1, 1997

One of the most common critical areas of longwall mining in terms of ground stability are the gateroad and bleeder entries. These critical entries provide much-needed safe access for miners and allow for adequate ventilation required for dilution of hazardous airborne contaminants and must remain open during mining of a multi-panel district. This paper focuses on the stability of the longwall entries subjected to a single abutment load such as bleeders, first tailgate, and last headgate. First tailgate and last headgate are also referred to as blind headgates and tailgates. A study of a longwall district through conditions mapping, support evaluations, and numerical modeling was conducted and evaluated by researchers from the National Institute for Occupational Safety and Health (NIOSH). The condition mapping and support evaluations were performed on entries that spanned the previous five years of mining and relied on a diverse selection of supports to maintain the functionality of the entry. Numerical modeling was also conducted to evaluate various support types with further investigation and comparison to the condition mapping. The study demonstrated the importance of the abutment load decay versus distance from the gob edge, the potential for a reduction in material handling related injuries, as well as optimal usage of secondary and standing support.

Jan 7, 2020

By John E. Urosek, Dennis A. Beiter, William J. Francart

In This Chapter [Designing bleeder systems Examining and maintaining bleeder systems Evaluating bleeder system effectiveness] INTRODUCTION Bleeder systems are that part of the mine ventilation network used to ventilate pillared areas in underground coal mines. Pillared areas are those in which pillars have been wholly or partially removed, including the areas where coal has been extracted by longwall mining. Bleeder systems protect miners from the hazards associated with methane and other gases, dusts and fumes, and oxygen deficiency that may occur in these mined-out areas. Effective bleeder systems control the air passing through the area and continuously dilute and move any methane-air mixtures and other gases, dusts, and fumes from the worked-out area away from active workings and into a return air course or to the surface of the mine. A bleeder system includes the pillared area (including the internal airflow paths), bleeder entries, bleeder connections, and all associated ventilation control devices that control the air passing through the pillared area. Bleeder entries are special air courses designed and maintained as part of the mine ventilation system. [This chapter focuses on the design, examination, maintenance, and evaluation of bleeder systems in underground coal mines.] The history of coal mine explosions in the United States is a reminder of the importance of adequate ventilation. Some of those disasters were the result of inadequately ventilated pillared areas. The importance of developing bleeder systems to ventilate these pillared areas and evaluating the bleeder system’s effectiveness is reflected in present-day federal regulations. For more information on bleeder systems, see Tisdale [1996] and Urosek and Francart [2002].

Jan 6, 2006

By W. B. Evans, D. P. Taylor

"ANFO has two major disadvantages as an explosive low density and no water resistance. ANFO can be blended with more dense, water-resistant explosives to form ""Heavy ANFO"". The use of emulsion or slurry explosives as a matrix is an attempt to correct deficiencies on the basic ANFO while maintaining cost effectiveness.This paper will deal with four main topics.1. Product description, general properties, strengths and weaknesses.2. Technology of ""Heavy ANFO"" , the emulsion matrix concept and the range of products.3. Relative performance and economics in various rock types.4: Current status in Canada and worldwide, and the expectations for future use.IntroductionANFO has been in use for roughly three decades and remains the explosive of choice where conditions are suitable. ANFO has not become the universal explosive - despite its undoubted superiority in cost effectiveness - because it has serious flaws as an explosive. The most serious of these flaws are the low density and absence of water resistance in ANFO. Low density implies a low concentration of explosive energy in a borehole. The amount of energy available can be increased by. adding an energetic material, generally aluminum, or by drilling more holes. Both solutions add considerably to the over-all costs. The absence of water resistance in ANFO is inherent and can only be overcome by changing the fundamental nature of the product. The history of research in the explosives industry since the advent of ANFO is mainly the story of the various attempts to overcome one or both of ANFO's shortcomings.Many technologies and products have been developed to compete against ANFO, among them slurries, emulsion s and the so-called Dense ANFOs (ANFO with an extra nitroalkane liquid sensitizer). None of them was cost-competitive with ANFO so their market penetration has been limited to wet holes or specialized applications. The exception to this result is Heavy ANFO. The aim here was to have the best of both worlds, the high density and water resistance of emulsions or slurries plus the low cost of ANFO. The concept is very simple. ANFO is about 50 % air, roughly 30% in the prills and 700,10 between the prills . The air in the prills provides the necessary sensitivity but the air between them is waste volume. If one fills this volume with a high density, waterproof product, the resultant mix will be denser and more water resistant than ANFO and with very little added cost. This basic concept was invented by B. Clay in the 1970s and is covered by Canadian Patent No. 1 115 959. The water resistance and/or density of the mix can be tailored by changing the emulsion level. Because Heavy ANFO is relatively inexpensive while providing good in-hole densities and water resistance, it can compete successfully against all other bulk products. It competes against ANFO and Al / ANFO by allowing pattern expansion and reducing over-all costs while it competes against emulsions and slurries on price."

Jan 1, 1987

Aspects and anomalies in the present Standard Specifications for Blended Cements which may have operated in Australia against the development of the greater use of Slag Blended Cements are noted. Estimates of slag and ash usage in Australia are given and the need for further research with local materials stressed.

Jan 1, 1979

By G. Ward Wilson

Waste rock and tailings may be combined through intimate blending to create new materials with superior physical and hydraulic properties. The new material, termed Co-Mix, has high shear strength characteristics, low compressibility, low hydraulic conductivity, and a high water retaining capacity. Co-Mixed tailings and waste rock may be used to construct cover systems, internal barriers and seals, confinement structures and full depth waste repositories. Field scale test trials using Co-Mixed blends of waste rock, tailings and slag have been constructed at the Copper Cliff Mine in Sudbury, Canad. These lysimeters will be used to evaluate the performance of the new material for cover systems that may potentially be constructed on the tailings impoundment upon closure. In this sense, the paper point out the construction of the lysimeters with respect to expected field performance during the spring snow melt period and summer to produce cover systems for closure.

Sep 12, 2005

By C. Pace, D. Darlington, A. Montera, C. Lingren

"A phosphate beneficiation plant in Utah is using isotope-based Prompt Gamma Neutron Activation Analysis (PGNAA) technology to analyze the entire slurry streams of the incoming feed and final product in order to adjust the flotation circuits in near real time and optimize the plant output. The plant has gained greatly improved visibility/control and has reduced product variability for improved profitability and product quality. This paper takes a look at the economics as well as application details and the difference this technology provides in a phosphate application. SIMPLOT PHOSPHATES INTRODUCTION Simplot’s Vernal, Utah Phosphate Mine and Mill are located in the northeast corner of the state in the Uinta Mountains along US Highway 191, eleven miles north of the town of Vernal. The phosphoric acid and fertilizer plant fed by the Vernal mine is located 94 miles Northeast of Simplot Phosphates in Rock Springs, WY.At the Vernal plant, loader and shovel mining to 85 Ton capacity trucks is done at an annual rate of 3.8 Million tons of ore. Run of mine ore is crushed in a mineral sizer to minus 14 inch diameter at the rate 11,500 tons a day and transported to the SAG Mill’s 130,000 ton surge stockpile by overland belt. ORE RESERVES The ore is a Phosphoria Formation of sedimentary rock type dating to the Permian Age. The ore body rests over a 25 mile area on Weber Sandstone from the Pennsylvania and Permian geologic period. Layers of Phosphate Rock can vary in thickness from 0.3 up to 2.1 feet, alternating with layers of Mudstone. The eastern edge of the ore’s body Panel “G” runs 16 feet deep with a feed grade of 21.5% P205 with lower MgO diluents of less than 2.79%."

Jan 1, 2016