Search Documents

By A. Pratt

Portland cement is primarily used to solidify backfill in underground mine workings and it represents a major cost in mining operations. CANMET-MMSL has invented an alternative binder technology that does not contain any amount of Portland cement and is made using waste materials, such as development rock and smelter slag. The technology has been successfully tested with many types of base metal and ferrous slag. Research conducted in collaboration with several mining operations in Canada has shown that the CANMET-MMSL binder has considerable potential as a replacement for Portland cement in mine backfill. An integral part of the overall mining operation, backfill is used for two main purposes: safety and environmental remediation. Depending on the mining method used, backfill provides a working surface, stabilizes stope and pillar walls, as well as the surrounding rock mass, and controls caving of stope backs. There are several benefits associated with the replacement of Portland cement in backfill, including reductions in (i) the footprint by placement of slag waste underground, (ii) the environmental effects and long term liability resulting from disposal and containment of slag waste on surface such as acid rock drainage, (iii) GHG as a result of reduced Portland cement usage (the production of 1 ton of Portland cement produces 1 ton of GHG), and (iv) the significant costs associated with reduced Portland cement usage.

May 1, 2010

By Kristie Tarr

Portland cement is primarily used to solidify backfill in underground mine workings and it represents a major cost in mining operations. CANMET-MMSL has invented an alternative binder technology that does not contain any amount of Portland cement and is made using waste materials, such as development rock and smelter slag. The technology has been successfully tested with many types of base metal and ferrous slag. Research conducted in collaboration with several mining operations in Canada has shown that the CANMET-MMSL binder has considerable potential as a replacement for Portland cement in mine backfill. An integral part of the overall mining operation, backfill is used for two main purposes: safety and environmental remediation. Depending on the mining method used, backfill provides a working surface, stabilizes stope and pillar walls, as well as the surrounding rock mass, and controls caving of stope backs. There are several benefits associated with the replacement of Portland cement in backfill, including reductions in (i) the footprint by placement of slag waste underground, (ii) the environmental effects and long term liability resulting from disposal and containment of slag waste on surface such as acid rock drainage, (iii) GHG as a result of reduced Portland cement usage (the production of 1 ton of Portland cement produces 1 ton of GHG), and (iv) the significant costs associated with reduced Portland cement usage.

Oct 1, 2010

By T. Patching

"COAL MINING at Canmore, Alberta, began in 1886 and continued there until July 1979. A comprehensive review of the Canmore operations is not available, but the following notes have been prepared to accompany references where more complete information about the operations and problems encountered may be found. The coal measures at Canmore occur in the Kootenay formation of Lower Cretaceous age, and at least twelve seams of varying thickness and horizontal extent have been recognized. The coal, of high quality, ranges from semi-anthracite in the lower seams to low-volatile bituminous in the upper seams. The strata of the Canmore area form an asymmetric syncline, the western limb being overturned to vertical by the Palaeozoic strata of the Mount Rundle Range. The eastern limb is more gently sloping, its dip ranging from IO to about 40 degrees. Tectonic movements have created a troubled and complex coal field. The seams were initially not regularly or uniformly deposited, and mountain-building activity folded and faulted the strata and in many places sheared and crushed the original structures of the coal(l,2,3,4,5). The lack of continuity of the seams, and changes in thickness and inclination, made longrange mine planning difficult and necessitated flexible methods of work, and the local disturbances sometimes created problems in roof support and contributed to the occurrence of sudden outbursts of coal and gas. Almost all of the coal was produced from underground operations but a few relatively small V-cut mines were worked along surface outcrops. These have all been filled in and revegetated. The basic method of underground work was by room-and-pillar, but many variations in layout and sequences were employed. Gangways were driven along the strike and pillars were formed by raises or slopes and crosscuts. Pillars were recovered to the extent that ground conditions permitted by splitting or taking 'skips' from the sides of the raises or splits or crosscuts. Because of the variety of conditions that existed in the field a considerable range of cutting, loading and support methods were employed, including hand-loading, slushers and scrapers, duckbills and shaker conveyors, mobile loaders and continuous miners. Except for the coal obtained by continuous miners most of the coal was broken out by blasting when driving narrow working places or by air picks when cutting from a face. In the early years hand loading onto cars or conveyors predominated. A continuous miner was introduced into Canmore in 1959 on a trial basis, and another was subsequently acquired, in order to minimize blasting and hand loading, but problems in operating these machines in inclining seams and difficulties in providing safe roof support for the machines and workers restricted their efficient use. Another major difficulty with the use of continuous miners was the problem of ventilating development headings in the very gassy conditions. In the early 1970s they were replaced by electric and compressed air slushers and scrapers, resulting in a general increase in productivity, roof control, safety, and flexibility of operations(1.6,7,8.9)."

Jan 1, 1985

The Broken Hill Proprietary Company Limited (BHP) started as a silver-lead-zinc mining company in Broken Hill, New South Wales, Australia in the 1880s. Since then it has diversified into the resource industries of steel, iron ore, coal, petroleum and copper. BHP World Minerals is a Business Group of BHP which is one of the worldÆs largest and most diverse mineral resource enterprises. BHP supplies raw materials for steelmaking, copper concentrate and other mineral commodities to customers in more than 45 countries. BHP World Minerals has operations spread throughout the world û in Australia, the United States, Brazil, Zimbabwe and Canada. Commodities produced by BHP World Minerals currently include silver, lead, zinc, titanium minerals, platinum group metals and coal. The BHP World Minerals Cannington silver-lead-zinc mine in Queensland, Australia is a return to the cradle of BHPÆs early silver-lead-zinc years. This paper compares the success factors and challenges at Broken Hill and Cannington.

Jan 1, 1998

The Cannington silver lead zinc deposit is located near Mt Isa in North West Queensland. This world class orebody is owned by BHP World Minerals (BHP) and is estimated to contain 45 million tonnes of ore at an average grade of 11 per cent lead, four per cent zinc and 500 grams/tonne silver. At BHPÆs planned 1.5 Mtpa extraction rate, the mine life will exceed 20 years. Construction of the underground mine, which commenced in August 1993, was carried out by Peabody Resources Ltd (Mining Services Division) (PRL) for BHP Minerals Pty Limited (BHP) under contract packages totalling approximately $100 M using several innovative techniques to deliver safety, quality and time related project goals. Client/Contractor Partnering, resulting in harmonious working relationships, a combined commitment to the achievement of an excellent safety record, and a seamless transition from the construction phase to operation of the mine, has been a feature of the project.

Jan 1, 1998

By J. J. Baz-Dresch

"The Cannon Mine, a joint venture between Asamera Minerals (the operator) and Breakwater Resources, is located in the centre of Washington state at the eastern base of the Cascade Mountains. The mine complex is located three blocks south of the city limits of Wenatchee, part of an urban area with a total population of 47 000. The closest residence is 350 feet from the mine portal.The B-Neath zone is a narrow, high-grade, downward extension of the southern tail of the mine's main ore body, the B-North zone. It also underlies the northernmost portion of the B-West zone (Fig . I) . The ore is usually reasonably competent but completely surrounded by very weak rock consisting of shear zone and unsilicified sandstones and siltstones.The zone has maximum dimensions of 420 ft in thickness, 500 ft in length , and 200 ft in width . The economic reserves extend from the 70-ft elevation (elevation above sea level) to the 630-ft elevation and consist of about 1.3 million tons of geologic reserves (proven and probable) at an average grade of 0.33 ounces per ton.Acquisition and ExplorationInitial DiscoveryThe initial discovery of the B-Neath zone was made by Tenneco Minerals during July through September, 1984. Their 22-hole surface drilling program consisted of 18 200 ft of drilling. Tenneco Minerals had acquired the 91/2 acre lease from United Mining Corporation.Asamera Minerals subsequently purchased Tenneco's lease in July, 1985; Tenneco retained a royalty position which was later purchased by Echo Bay Mining.Follow-up drilling by Asamera Minerals consisted of both surface and underground drilling. Eight surface holes (7200 ft) were drilled commencing in December, 1985. Following evaluation of the geologic data, an access drift was driven on strike along the top of the ore zone on the 500 level. Diamond drilling from this platform consisted of 17 200 ft in 79 holes."

Jan 1, 1990

By John Vickers, William H. Hover, Paul C. Schmall

"Any sudden subsurface issue that threatens the stability of existing buildings or infrastructure is cause for immediate investigation and prompt remedial action. Nowhere is this more true than the nation’s dams and levees. A breach of any kind, no matter how small initially, has the potential to be catastrophic and impact a wide downstream area. Addressing the problem quickly and effectively is therefore critical. When a turbid water discharge developed from a rock drainage embankment at the toe of the earthen dam impounding Cannonsville Reservoir, near Deposit, NY, the source of the problem was quickly identified as resulting from an artesian water release from an underlying permeable silty sand and gravel formation during drilling of three exploratory boreholes in preparation for construction of a hydroelectric plant at the downstream toe area of the dam facility. Work was halted, intense 24-hour monitoring was implemented, and as a risk reduction measure NYCDEP began to draw down the reservoir’s total storage at a rate of a billion gallons per day. Input sought from contractors within the geotechnical community helped result in the design and development of a deep well system to control the artesian pressure. Once this primary objective was accomplished, modified compaction grouting was performed at the borehole locations to densify loosened soils, fill any voids created by the discharge activity, and seal off the permeable aquifer. This paper discusses the dewatering program, specialized drilling techniques required, monitoring and verification of pressures within the dam, and the grouting program.BackgroundCannonsville Dam, owned and operated by the New York City Department of Environmental Protection (NYCDEP), is located in Deposit, New York on the West Branch of the Delaware River and impounds the Cannonsville Reservoir. Built between 1959 and 1964, the dam has an impervious central and upstream core zone keyed into the glacial till foundation, a semi-pervious downstream embankment zone, and a rockfill toe and is approximately 2,800 ft (853.4 m) long and 175 ft (53.3 m) high. The dam is formed by two embankment sections. The left section forms the main embankment blocking the main river channel, while the right section is constructed over a topographic saddle or low ridge. Reservoir level is actively influenced by withdrawals through the West Delaware Tunnel, based on water supply need. Under normal circumstances, water is continuously discharged downstream to the Delaware River."

Jan 1, 2016

The structure of a mine ventilation network (M.V.N.) can be represented graphically using either the mine plan (map) itself or a number of other types of diagrams. In the U.S., the two most common approaches are the line and the schematic diagrams (see Figures 1 and 2). The purpose of this paper is to introduce another type of diagram, called the canonical diagram (6). The method of M.V.N. representation which uses canonical diagrams is used extensively in Europe, and especially in Poland, where it was developed. The canonical diagram is a noncalibrated topological image of a ventilation system. It gives a simple representation of the ventilation network, allows for the classification of currents within it and enables rapid computer analysis and computation, as well as the representation of the results. It is especially useful in studying and controlling the air flow, and it may be a life saving tool in conducting rescue operations during and after mine fires.

Jan 1, 1986

By Taekhee Lee, Steven Mischler, Shawn Vanderslice

Diesel-powered equipment is widely used in the underground mining industry and their popularity results from properties including efficiency, versatility, reliability, and durability. In the U.S. approximately 7,700 diesel engines were used in 177 underground metal and nonmetal mines as of 2005 [MSHA 2005], and these numbers have likely increased since that time. Diesel engines have been shown to be a major contributor to submicron carbonaceous, respirable, and total particulate mass in the air of underground metal mines [Zielinska et al. 2002, McDonald et al. 2003], and their extensive use results in approximately 13,000 underground metal/nonmetal (M/NM) miners (MSHA 2005) in the U.S. being potentially exposed to aerosols and gases emitted by diesel engines (MSHA 2001, MSHA 2006). Exposure to diesel exhaust has been linked to adverse health outcomes including cancer, cardiovascular, and respiratory diseases (Attfield et al. 2012, Silverman et al. 2012), and in 2012 diesel exhaust was categorized by the International Agency for Research on Cancer (IARC) as a Group 1 human carcinogen (IARC 2012). Exposure to diesel particulate matter (DPM) is especially concerning for underground miners since underground mine environments have been shown to have some of the highest levels of diesel exhaust in the U.S. (EPA 2002, MSHA 2001, MSHA 2006, Pronk et al. 2009). Due to the potential for elevated DPM concentrations in mines, the Mine Safety and Health Administration (MSHA) promulgated a rule to limit exposures of metal/ nonmetal underground miners to DPM to an eight-hour time-weighted average (TWA) of 160 μg/m3 total carbon (TC) (MSHA 2001, MSHA 2006, MSHA 2008). Since this rule went into effect, DPM exposures have been reduced, but are still elevated when compared to other occupations (Pronk et al. 2009, Noll et al. 2015). MSHA compliance data between 2005 to the present show that underground blasters represent 21% of all DPM overexposures in M/NM mines and are one of the highest exposed professions in mining often resulting from low ventilation in the area where blasters are working. Because mines have difficulty controlling DPM in these low ventilation areas, additional control technologies may be needed to reduce exposures. Administrative controls, where miners work on off schedules or upstream of diesel vehicles to avoid the exposures to DPM (Noll et al. 2015) is one possibility, but these types of solutions are not always feasible or practical. A canopy air curtain is another potential control technology to help reduce exposures of blasters to DPM. Listak and Beck (2012) showed that this control technology reduced respirable dust concentration under a roof bolter’s canopy by 67%–75% and recommended air velocities greater than 0.5 m/s for dust reductions of greater than 50%. Additional work showed that a canopy air curtain could be designed for a shuttle car, and some initial testing by the National Institute for Occupational Safety and Health (NIOSH) showed reductions of respirable mine dust between 66% to 70%. As seen in Figure 1, the canopy air curtain delivers clean air over the operator’s breathing zone. A fan draws in air through a filter to capture the dust and then supplies clean air beneath the canopy where a miner is working. The use of the canopy air curtain to reduce exposures to diesel particulate matter was first discussed by Noll et al. (2020). In this study the diesel canopy air curtain (DCAC) reduced the DPM concentrations under the canopy by up to 90%. For this research the DCAC was designed to attach to the basket cover of an ammonium nitrate fuel oil ( ANFO) loader (Figure 2) and provide clean air blowing over the miners as they work in the basket. The initial tests used clean air drawn from the mine’s intake and did not try to filter the DPM from the air. Filtering DPM has extra challenges when compared to filtering mine dust particles. The particles of DPM are smaller (submicron and nanometer) than dust particles (greater than 1 micron); therefore, the filtration system must be adjusted to capture submicron particles. A MERV 13 filter was used in previous canopy air curtain research on mine dust control, but this filter is only designed to capture 50%–75% of submicron particles, and this capture efficiency is too low for removing DPM, so a higher efficiency filter is needed. Higher efficiency filters increase the pressure across the filter media which results in decreased airflow or leaks around the filter and reduces the effectiveness of the control for protecting miners from DPM. The optimal filter needs to capture DPM particles at a high efficiency while still allowing the needed airflows to prevent contaminated air from entering the miner’s breathing zone. Listak and Beck (2012) recommended velocities greater than 0.5 m/s for dust reductions of greater than 50%. However, airflows too high have been shown to reduce miners’ thermal comfort; Roghanchi et al. (2016) suggest the optimal velocity for thermal comfort is between 1–2 m/s. Thus, airflow over the miner should be limited to the range of 0.5 to 2.0 m/s. This current study presents the results from research evaluating the reduction of DPM concentrations, under the DCAC, when using a higher efficiency filter (MERV 16) to remove DPM from the DCAC airstream.

Feb 1, 2024

Cansolv® S02 Scrubbing Technology was described in a paper in Copper/Cobre 03. Four years on, the technology is operating at a full scale production facility.Hindustan Zinc Limited expanded their capacity by installing the AUSMELT process. The process proceeds through smelting, slag reduction, slag cleaning and holding stages sequentially in the same vessel, resulting in widely varying off gas characteristics. The off gas is suitable for treatment is a conventional acid plant for a modest proportion of the day, but at other times produces off gas too high in S02 to be discharged to atmosphere. Cansolv® S02 Scrubbing Technology was identified as a means of effectively removing the S02 down to low levels from the off gas during all stages of the pyrometallurgical process. Furthermore, the Cansolv® S02 Scrubbing System Technology produces high purity S02 that allowed for the captured S02 to be directed to an existing acid plant, avoiding the capital cost of new acid making capacity.

Jan 1, 2007

By Valérie Léveillé

As new legislation drives to lower SO2 emissions from metallurgical plants, plant managers face the challenge of keeping their costs under control. The Cansolv® SO2 Scrubbing System has been broadly adopted in the non-ferrous industry as a cost effective solution for smelter operators to meet the new SO2 emissions targets. The Cansolv® SO2 Scrubbing System is an amine-based regenerable process that selectively absorbs SO2 from a variety of gases, including dilute smelter gases, such as furnace and converter gases. The system produces a pure, water-saturated SO2 byproduct stream, which can then be directed to the front end of a sulfuric acid plant for conversion to sulfuric acid. When deployed in a smelter complex, the Cansolv® SO2 Scrubbing System may also be used to process acid plant tail gas, allowing single absorption sulfuric acid plants to achieve emissions an order of magnitude lower than that of a double absorption acid plant with a lower capital investment. Depending on inlet gas temperature SO2 emissions in the treated gas can be controlled to as low as 55 mg/Nm3. This paper will describe some of the applications where customers have or are planning to use the Cansolv® SO2 Scrubbing System and what as well as which features and cost advantages for the treatment of smelter gases were key to the technology choice.

Jan 1, 2009

By L. D. Frink

THOSE actively interested in mining are fully aware of the ever-increasing difficulty of making conditions such that efficient work can be clone in underground openings, especially as higher rock temperatures are encountered in depth. This is also true where an effort is being made to cut down the burden of overhead expense by working headings 24 hr. in a day if blasting is done as often as is possible in that time. That the conditions resulting from both these causes have driven the native-born Americans from the mines and that their places have been taken by less efficient foreigners is a fact that we must all admit. The great war now being fought in Europe and the educational qualification clause written into our immigration law by the last Congress will probably limit very materially the supply of labor, such as we are now using in our mines, and will force upon mine operators the necessity of making this work appeal again to Americans. Metal tubing, with blower or exhaust fans, has long been used in supplying air to dead ends where natural ventilation is impossible, or in driving the smoke from such places, or in doing both, as the need might be. Here in Butte we have now come to use canvas tubing very extensively and find that it has many advantages not possessed by the metal. The use of flexible tubing is not new, but it has not been generally used in mining operations. Recent improvements, however, in the canvas itself and in the jointing of sections and manner of suspension have so increased its usefulness that it promises to add much to the efficiency of mining. There is now on the market a product that is impervious to air, is fireproof, and has a system of jointing which, permits it to be put up or taken clown in a few seconds. In this article an effort will be made to explain the manner in which canvas tubing is being used in the North Butte company's operations at Butte, Mont. The accompanying photographs will, I hope, help make clear what may be done with this material.

Jan 1, 1918

By Ron Light, Doug Applett

"HistoryThe Nanisivik mine began operation in October 1976 as the world's most northerly metal mine and the first permanent industrial project in the Canadian High Arctic. Located 700 km north of the Arctic Circle on Baffin Island's Strathcona Sound, exploration by Texasgulf Inc. between 1957 and 1970 had outlined the ore deposit. In 1974, Nanisivik Mines Ltd. was formed with Mineral Resources International, the Government of Canada, Metallgesellschaft and Billiton being shareholders, and Strathcona Mineral Services Ltd. providing project management. In 1996, Breakwater Resources purchased the mine from Alberta Energy Corporation Limited which had recently acquired the assets of then owners Conwest Exploration Ltd.Ore DepositThe main ore deposit is very flat, approximately 80 m in width and varying in thickness from 3 m to 16 m. The length of the deposit is approximately 3000 m with satellite zones located on the perimeter of the main zone. The economic mineralization is sphalerite with minor galena and silver. The sphalerite and galena are coarse grained and associated with pyrite as the main gangue component with minor inclusions pf dolomite and calcite within the deposit. The deposit being hosted in a permafi·ost environment creates a number of challenges. Dry drilling is employed in room and pillar production drilling. The permafrost aids in the stability of both the pillars and the back."

Jan 1, 2000

By Derek T. Novotny

Blasting cap precision is of major importance to advanced blast design. New technologies have introduced the use of microchips within detonator casings in the hope that the electronic control of the timing element will increase the accuracy of the cap and therefore improve the results of perimeter control blasting applications. The electronic detonators have proven to be accurate in timing tests done to date. They boast cap scatter results to microsecond accuracy, but the question is, does this degree of accuracy actually prove to be beneficial during practical use in the industry, or are conventional technologies applicable.

Jan 1, 1998

By L Neems

In conjunction with Orica Explosives, Worsley Alumina have managed a program of continuous improvement to their cap rock blasting over the last two years. Blasting conditions are challenging because of the hard and shallow nature of the material. Blasting costs must be controlled and the environmental consideration of noise and dust is critical. Worsley have sought to determine the optimum balance between drilling and blasting costs and fragmentation. As the cap rock has few inherent weaknesses, loader productivity is strongly controlled by the degree of fragmentation from blasting. The optimum blasting solution is also constrained by maintaining airblast levels at the surrounding residences below 115 dBL . The major blast design parameters optimised during the program were stemming type, stemming length, powder factor and blasthole diameter. A series of carefully managed trial blasts were fired during 1997 and 1998 to quantify the effect of these parameters. Fragmentation was digitally measured using OricaÆs Powerseive G technique. Shovel productivity, airblast levels and blasting costs were also quantified. As a result of the project, Worsley now have an increased knowledge of the key parameters driving blast performance, and their consequent impact on downstream processes, the environment and total mining cost.

Jan 1, 1999

By K. Tajrych

Time and again, lives are lost in underground cave-ins only be- cause there is no quick, sure way of locating the victims. When such accidents happen, rescuers must usually depend on the testimony of eye- witnesses for information on the whereabouts of trapped miners. Seldom is this information reliable. The witnesses themselves have just been through a traumatic experience that has distorted or destroyed their sense of time and place. A far more reliable method of finding men underground has recently been developed by the Coal Mining Research Institute of Ostrava, Czechoslovakia. With this system, a miner can be located with adequate precision even if he shows no sign of life. For the system to work, the miner need only have his electric cap lamp somewhere nearby. The system consists of a minute radio transmitter operated by the lamp battery (Fig. 1). This tiny transmitter continuously emits high- frequency electromagnetic waves that can be picked up by a sensitive direction-finder receiver in case of accident.

Jan 8, 1969

By Koji Matsubara, Yoshiaki Iguchi, Shoji Hayashi

Iron ore particles of a limonite iron ore were reduced completely with H2 at 1023K to 1273K in a fluidized bed. Then, at 973K, the formed iron was exposed to HrH2S mixtures (sulfur activity, as=0.5) for 3.6ks and carbidized with CO-H2-H2S· mixtures at 0.1 MPa. During the carbidization, the particles of about 150mg were sampled at every 600s interval. The sampled particles were analyzed by XRD and chemical analysis for C and S to evaluate the content of Fe3C, Fe5C2, Fe and free carbon. The reaction extent is defined as fo=Xfc3C +xFc5c2; x is the molar fraction of Fe in Fe3C. The carbidization curves can be fitted very well to -ln(l-f0)=g(pb T)t; g(p; T) is the carbidization rate, i.e. the carburization rate on the pore surface of reduced iron. The rate is found to be nearly proportional to the specific surface area of reduced iron, a P 0 , which decreases with increasing the reduction temperature. The value of a P 0 does not change by the carbidization and the stability of the iron carbide product in the atmosphere increases with the temperature.

Jan 1, 2000

By Jeannine Wendy Salas Huamán

Dado que la empresa minera tiene como objetivo el fortalecimiento de la responsabilidad social y ambiental para la AID (Puno), se implementa un programa de actividades que responda a la responsabilidad social y ambiental. En ese sentido, el presente texto describe la capacitación como una herramienta de una logística -en tanto se entrene a los pobladores de la AID para que puedan brindar servicios a la minera, se concilie la explotación minera con la población mediante la logística y se establezca una alianza con los pobladores formándolos como proveedores, de forma que se obtenga una ganancia conjunta.

Nov 1, 2013

By T. Kerr, C. Mattich, J. Wilson

"In refractory gold concentrates, gold is occluded in sulphide minerals preventing efficient cyanide leaching. Hence, roasting is used to oxidize sulphur and organic carbon, the latter being necessary to minimize recovery loss through the preg-robbing effect. In 2009, Outotec commissioned the circulating fluidized bed roaster at Syama gold mine in Mali. Since 2013 Resolute and Outotec have been implementing improvements to the roaster performance with the capacity increasing from 8000 t/month in 2013 to above 13,000 t/month in 2016, while achieving a residual sulphide sulphur and organic carbon contents of below 0.1 wt.% and 0.4 wt.%, respectively. Thus a gold recovery in the CIL of above 90% is attained. In 2016, Outotec audited the Syama roaster. The analysis resulted in the Low Carbon Roaster (LCR) upgrade concept which (i) allows re-processing of calcine dust from the spray cooler and ESP after pelletization and (ii) allows the roasting of a further fine-organic carbon rich feed, i.e. de-slime circuit tailings. The LCR upgrade aims to reduce organic carbon to <0.2 wt.% and increase roaster-leaching gold recovery by >3%. Project development included extensive testwork. The LCR process is expected to become operational during FY 2019.INTRODUCTION Double refractory sulphide ores exhibit the characteristics of gold locked within pyrite grains, in the presence of preg-robbing natural (organic) carbon. Hence, to achieve high recovery during subsequent processing steps, i.e. cyanide leaching, oxidation of sulphide sulphur is required, producing a porous calcine by way of a roasting step. This allows for the gold contained within the pyrite grains to be accessible during cyanide leaching. Furthermore, it is necessary to oxidize the organic carbon. Oxidizing the organic carbon is essential as gold recovery loss occurs as a result of gold-cyanide complexes being adsorbed on organic carbon, this phenomenon is termed as preg-robbing (Miller et al., 2016). The gold absorbed on the organic carbon is lost, reporting to the tailings stream. Hence, the aforementioned oxidation of sulphide sulphur and organic carbon is the process goal. Nonetheless, the latter must occur at a controlled temperature which is concentrate/ ore specific, since the pores of the produced calcine should not sinter, as this makes the gold contained in the calcine less accessible during leaching, leading to gold recovery loss. The tight temperature control requirement is a decisive factor in the choice of a Circulating Fluidized Bed (CFB) as the roasting reactor, due to the excellent mixing characteristics of the CFB which results in temperature homogeneity of (+/-10°C). Roasting of double refractory ores, as described above, can be included in the flowsheet after comminution and grinding, a process termed as whole ore roasting, or by including a flotation circuit termed as concentrate roasting. Roasting the flotation concentrate results in less solid flow, increased sulphide sulphur grade and organic carbon content resulting in a higher heating value and higher gold content. A typical composition of the Syama ore and concentrate is given in Table 1. Ore average values presented correspond to the period 2015, while concentrate values are typical for the flotation performance throughout the period 2012–2015."

Jan 1, 2017

By T. Krumins, F. C. Ruff, M. Eichhorn, L. Zunti

Hatch Ltd. has recently completed a project to increase refractory gold ore processing capacity at Newmont Mining Corporation’s Twin Creeks facility. The objective of the project was to increase throughput by approximately 10% by adding a third autoclave feed pump to each of the two autoclave circuits. To minimize project capital cost, autoclave feed pumps from Newmont’s decommissioned Lone Tree facility were evaluated and found to be suitable for this new service. The existing pressure oxidation circuit was reviewed in a debottlenecking study to determine other upgrades required to facilitate the increased throughput. Interruption to operations was minimized with a detailed construction plan, supplemented with detailed 3D layout model sequencing studies. The focus of this paper is project development, multi-discipline design considerations, and implementation results.

Jan 1, 2014