Search Documents

By E. E. Donath

THE coal hydrogenation process is well known as a means for the production of liquid fuels -from coal. In this paper the possibilities of the coal hydrogenation process as a source of chemical raw materials will be discussed. The recovery of chemicals from coal hydrogenation products necessitates some modifications and additions to the equipment used for the production of fuels. The conversion of coal into liquid fuels such as gasoline requires two steps: liquid phase and vapor phase hydrogenation. Intermediate oils obtained in the liquid phase contain oxygen and nitrogen compounds, especially aromatic compounds, since the coal itself is composed mainly of cyclic compounds. These oils are the raw material for the separation of high molecular weight aromatics and of tar acids and tar bases. The relative amounts of heavy and middle oil-boiling above and below, e.g., 325°C-can be influenced by temperature, residence time, and catalyst of the liquid phase hydrogenation. In the vapor phase hydrogenation a solid bed catalyst is used to convert the intermediate oil from the liquid phase operation into hydrocarbons of the gasoline boiling range. Essentially pure hydrocarbons with a low content of sulphur, oxygen, nitrogen, and olefines are obtained. Depending mainly on the catalyst, the high ring compound content of the liquid phase oil can be preserved and gasoline rich in aromatics obtained. However, with other catalysts, these ring compounds can be split into gasoline with a high content of isoparaffins.1 Again, depending on the operating conditions, products of varying boiling range can be obtained. Selection of catalyst and operating conditions therefore makes possible the production of different grades of motor fuel and also variations in the relative amounts of benzene, toluene, and xylene when aromatic hydrocarbons are produced. The schematic flowsheet, Fig. 1, shows the main steps of the coal hydrogenation process, and the product streams used for the recovery of chemicals are indicated. In the liquid phase hydrogenation stage, coal is made into a paste with recycle heavy oil. The coal paste is mixed with hydrogen and preheated at a pressure of 300 to 700 atm in heat exchangers and preheaters. The coal paste and hydro¬gen enter high pressure converters where the liquefaction of coal, conversion of the high boiling liquid materials initially obtained, into intermediate oils is performed at a temperature around 470°C. The reaction products enter the hot catchpot in which lower boiling oil vapors are separated from the residue containing unreacted coal, ash, and heavy oil. This residue, usually called H.O.L.D. (heavy oil let down), is processed to separate solid and liquid material. By thermal treatment of the residue, e.g., a coking process, distillate oil is obtained, which can be recycled as part of the pasting oil. This stream is rich in polynuclear aromatics and can be, and has been, used for the recovery of such material. The oil vapors and hydrogen from the hot catch-pot are cooled in heat exchangers and a cooler, and the condensed oil is separated from the recycle hy-

Jan 1, 1952

By John E. Pavlick

The availability of concentrated brines rich iodide, bromide, chloride, sodium, magnesium and calcium ions has led to extensive chemical manufacturing operations in Michigan. The brines, ranging 1,000 to 8,000 feet below the earth's surface, are the remnants of ancient oceans which periodically covered and receded over the land area which is now Michigan. After pumping the brine to the surface, iodine and bromine are extracted via an oxidative process. Iodine and bromine find application in catalysts, disinfectants, flame retardants, oil field fluids, film, and gasoline additives. Addition of alkalinity to the brine precipitates magnesium hydroxide, used in high quality refractories needed for steel manufacture. The brines are also the country's primary source of calcium chloride, employed in ice and dust control.

Jan 1, 1984

By N. S. Dalal, N. Leelarasamee, V. Castranova, K. Van Dyke, V. Vallyathan

"INTRODCICTIONSilicosis is the chronic fibrosing disease of the lungs caused by the inhalation of crystalline silica. However, inhalation of crystalline silica, may induce three distinctly different disease patterns; i.e., chrome silicosis, accelerated silicosis, and acute silicosis. These three disease patterns differ in their pathologic characteristics, clinical symptoms, onset of disease, and mortality. Many studies in the past have focused on the elucidation of mechanisms involved in the development of chrome silicosis. We recently reported that freshly fractured silica has surface properties that could make it more reactive with lung tissue than aged silica, and that this unique reactivity of freshly fractured silica may be involved in the pathogenesis of acute silicosis (Dalal et al., 1986; Vallyathan et al., 1988; Shi et II., 1988). Because freshly fractured silica could contain some moieties in an ""excited state,"" due to the breakage of silicon oxygen bonds, we postulated that the de-excitation of these moieties could produce light which could be monitored by a luminescence measurement technique. In addition, if this ""excited state'' of silica could trigger a greater biologic response by phagocytic cells, this activation could be monitored by a chemiluminescence technique in the presence of appropriate enhancers.This investigation describes for the first time the use of luminescence in the study of freshly fractured silica and its properties. Enhanced biologic reactivity of the freshly fractured silica with alveolar macrophages was monitored by the chemiluminescence technique.MATERIALS AND METHODSNative silica was obtained from the dust bank of the GenericRespirable Dust Technology Center, Pennsylvania State University, State College, PA, and ground for 3~ min in an agate ball mill. It was then sieved through a 20 micron mesh filter and used within 1 O min as fresh silica or stored in glass bottles for aging. X-ray energy spectrometry and X-ray powder diffraction studies on representative samples were made to confirm the mineralogic purity. All the silica samples were found to be 99 % pure with minimal detectable conlamination by metal ions."

Jan 1, 1990

By Hsu-Hui Hsing

In several previous studies from this laboratory (1-4) the autophobicity concept of Zisman and co-workers (5, 6) has been extended to gas phase adsorption processes. Low molecular weight alcohols adsorb on silica or alumina to yield novel isotherms in that monolayer adsorption occurs at low relative pressures indicative of strong bonding, but subsequently multilayer adsorption is quite sparse and diminishes with molecular weight of the alcohol. Such isotherms fit no standard classification scheme, however, in the vacinity of monolayer coverage alcohol isotherms give an excellent fit to the Langmuir or B. E. T. , Type I model (7). Monolayer adsorption is relatively irreversible and it is thus possible to prepare these chemisorbed layers and perform subsequent adsorption studies thereon. All indications are that the adsorptive properties on such films is radically different from that on the underlying alumina (4, 8) and in one study finite contact angles for hydrocarbon fluids were observed. One perennial conceptual difficulty is that there is no observed upper bound to the adsorption isotherm which would be necessary for autophobic adsorption to occur. The cause for this has been studied, and it is currently believed that adsorption is complicated by reversible capillary condensation at contact points between powder particles. The evidence for this is that large particle powders give less "apparent" adsorption at high relative pressures and in one very tedious study adsorption on planar sheets, oxidized aluminum displayed similar reduced uptake at high relative pressures when compared with high specific surface area powders (3).

Jan 1, 1974

By S. I. Sobol

Completeness of cobalt recovery from slag requires decomposition of maggemite and non - ferrous metal desorption with polymerized silicon-acid. Cobalt losses are reduced in leaching tai1s up to 200 g/t of iron.

Jan 1, 1993

By B. A. Watters, G. A. Parslow, F. H. Mcdougall

Carbonate-rich rocks occur at several localities within the Flin Flon volcanic sequence of the eastern Amisk Lake area. The rocks occur in two areas: as a group of small occurrences on islands within Amisk Lake and as two much larger linear belts running parallel to the regional structure east of Amisk Lake. Mineralogically, the rocks consist of talc and Ca-poor ankerite with occasional graphite. Segregation of these minerals and colour variation impart a well-defined planar fabric to the rocks and where the units are fairly continuous (e.g. Mosher Lake), their trend and attitude suggests a concordant relationship to the volcanics. Major and trace analysis of22 samples confirms the presence of two types, with one type being represented in each of the two areas. Most of the elements studied can be used to characterize the two groups, but three elements in particular give a clear separation: Mg, AI and Ni. Recalculation of the major element analyses, on a water and carbonate-f ree basis, indicates that one group (large concordant bodies with high MgO, high Ni and low AI20.J is altered ultrabasic material of peridotitic or dunitic composition. Because no relict igneous material is observed, and the contacts are apparently very sharp, it is possible that the hydration-carbonization process occurred simultaneously with intrusion, .in a closed system. The other group (small occurrences with relatively low MgO, low Ni and high AI203J represents alteration of basaltic rocks. AIthough some analyses suggest the introduction of calcium, as carbonate, along with the volatiles, the major oxides have remained remarkably stable during the alteration process(es).

Jan 1, 1981

By John W. Tieman

Coal is a term applied to vegetable matter which, through geological processes of heat and pressure, has had both its physical and chemical properties changed. Because its chemical composition is variable, geologists classify coal as a rock rather than a mineral. Peat represents the initial stages in the development of coal, although not classified as coal itself. PHYSICAL PROPERTIES OF COAL The physical properties are concerned with the characteristics of coal in its natural state, or prior to its end use as a fuel. For example, the hardness of coal determines the maintenance cost on coal handling equipment; the specific gravity of coal determines the coal preparation techniques used in a cleaning plant as well as the capacity of coal bins, boats and size of cargo, and other coal storage facilities. The physical properties are, of course, dependent upon the chemical constituents that make up coal, and thus all properties are interrelated. Specific Gravity The specific gravity of a body is the ratio of the weight of the body in air and the weight of an equal volume of water. The specific gravity of pure coal ranges between 1.25 and 1.70, generally increasing with rank. The most important use of this physical characteristic is the part that it plays in the cleaning of coal by wet wash methods. The basic principle on which these operate is that the specific gravity of coals differs from their associated impurities and that there is a relationship between the velocity of the fall of particles in water and their density. Since the specific gravity of slate is around 2.5 and pyrite is about 5.0, pyrite and slate will fall to the bottom of a container filled with water more rapidly than coal. If the water is given a pulsating motion by

Jan 1, 1973

By Okura T, Hino J

Coal utilization for copper flash smelting in Japan was initiated due to the sudden upheaval in the price of oil in the last ten years. A major portion of the heavy fuel oil has already been replaced by coal resulting in a corresponding decrease in energy costs. In addition to energy cost savings, an interesting metallurgical phenomenon was observed in flash smelting operations. Unlike oil combustion, coal is not burned completely in the shaft. A considerable fraction of coal particles remain on the surface of slag and are burned at the settler. Chemical investigation has shown that oxygen potentials at the settler have consequently decreased, bringing the slag and matte phases into reducing conditions, thus oxidation and reduction can coexist in one flash smelting unit. As a result, a decrease in magnetite and copper contents in the slag, elimination of furnace hearth build-up and dissolution of intermediate layer between matte and slag have been observed. In general, these led to improvements of furnace operations. However, thermodynamic investigations have shown that some minor elements such as As, Sb, Bi and Pb concentrate from slag to matte. Results evaluated on the basis of thermodynamic data relatively agree with practical observa- tions. Consequently, for coal utilization in flash smelting operations it will be necessary to control oxygen potentials from the stand- points of copper loss in slag and minor element Distributions.

Jan 1, 1987

By Woodcock J. T

During the dissolution of gold in fully aerated cyanide solutions the CN ion is the active agent, and consequently the usual method of evaluating the dissolving power of such solutions is to determine the CN- concentration analytically. The presence in the solutions of copper and/or zinc which themselves form complex cyanides, may result in erroneous conclusions as to the free cyanide ion concentration determined by titration.In this paper the theory of titration of such solutions has been developed, and potentiometric methods have been used to follow the behaviour of complex cyanides of copper and zinc. The results for cuprocyanides show Cu (CN)s to be the most important copper complex, and in addition they explain the reported low rates of solution of gold in copperbearing solutions which when titrated in the usual way, appear to have adequate free cyanide. An explanation of the misleading value of the titration is given, and suggestions for recognition of the condition are offered. Preliminary results for zinc-bearing solutions show that there is no satisfactory end-point for the titration of CN- in excess of that in the complex Zn (CN) 4=, which dissociates to CN and Zn(CN)g-.

Jan 1, 1950

By John J. Friel

The addition of dolomite to iron ore pellets improves their high-temperature reduction properties primarily by increasing their reducibility and raising their softening temperature. In this study we prepared dolomite-fluxed pellets from three different concentrates; Hibbing, a magnetic taconite, Knob Lake, an earthy hematite; and Carol Lake, a mixture of specular hematite with magnetite. The composition n of the concentrates is given in Table I. The pellets were subjected to standard physical tests and the following reduction tests: low temperature degradation, swelling, softening, and thermogravimetric analysis. Petrographic examination and electron microprobe analysis allowed us to evaluate the effect of composition and firing on the phase assemblage. Further, we were able to interpret the test results in terms of chemistry and microstructure. This approach enabled us to determine which fluxed composition best suited each of the concentrates.

Jan 1, 1980

By Jacques Ouellet, Ferri Hassani

"Within the mining industry paste backfill technology has evolved over the last two decades. This technology aims at producing safe and cost effective backfill of high strength. When used as cemented backfill underground the usual practice in the mining operations was to consider the backfill as a component under the production engineer responsibility. With its growing use in various site conditions some problems were encountered. Over time the mechanical characteristics of paste backfill could deteriorate. Investigations on these problems brought an increased understanding of paste backfill chemistry. Effectively, paste backfill is produced with tailings slurry having sometimes very complex chemistry and mineralogy. The bonding agents can be sensitive to the chemistry of these slurries. Today, a new understanding of the complex chemical reactions involved in cementing paste backfill is derived from concrete research literature. Cemented paste backfill is a manufactured product and as thus all steps involved in its making must be looked at. Both the processing engineers and mining engineers need to be involved. The proposed paper will go over the various developments and new understanding gained over the years on paste backfill chemistry. The authors had the opportunity to work with various Canadian mines that implemented paste backfill in their operations. Chemical alterations case study will serve to illustrate the importance of a good understanding of cement and paste chemistry. The authors will then conclude on research orientations needed to bring a more efficient use of paste backfill technology. The crucial role of the processing engineers in the paste backfill manufacturing will be discussed.INTRODUCTIONPaste backfill is usually prepared from a mixture of solids and water containing at least 15% particles smaller than 20 microns with the addition of binders for mechanical strength. Historically, tailings had been classified to extract the fines and only the coarse part was placed underground as sand slurry. Paste fill was researched in the last three decades to enable mining operations to use all the tailings, including fines, in backfill. The outcome of the early studies showed that paste fill provides high strength but due to preparation complexities and transportation problems is expensive. A greater understanding of the transportation mechanisms and advances in dewatering technology in recent years has resulted in more practical use of paste backfill."

Jan 1, 2002

By B. Zane Egan

The Calsinter process for recovery from fly ash involves sintering the fly ash with calcium sulfate and calcium carbonate at 1200°C, followed by a dilute sulfuric acid leach step. Flue gas desulfurization sludge containing calcium sulfite, calcium sulfate, and unreacted calcium carbonate may be substituted for the calcium sulfate and calcium carbonate. Conversion of aluminum in fly ash by the sintering process to an acid-leachable species was measured as a function of sintering time and temperature in the range of 800°-1200°C The sinter-leach steps were investigated using thermogravimetric analysis, x-ray diffraction, scanning electron microscopy, and elemental analysis. SEM photographs indicated that the glassy spheroids in the original fly ash were converted to a crystalline structure by the sintering reaction.

Jan 1, 1980

By R. K. Mehta

Existing acid mine drainage treatment techniques are not remedial In nature, i.e. though heavy metals can be removed from acid mine water, their presence in tailings and large quantities of these tailings tend to increase capital and operating cost for tailing management. This paper presents the results of a series of systematic tests which finally resulted In the development of the "ferrite" process for mine drainage of coal operations at ambient temperature. The role of pH, temperature, quantity of ferrous salt addition and degree of oxidation is investigated targeting the production of high emu spinel ferrites and effluent water complying regulatory standards with respect to Iron. manganese suspended solids and pH.

Jan 1, 1992

By G. Roy, D. R. Lentz, A. O. Wills

"Abstract - Diamond-drill hole DDH-B357, located 1.5 km north of the Brunswick No. 6 Zn-Pb- Cu-Ag volcanic-sediment-hosted massive sulfide (VSHMS) deposit, intersects three exhalative horizons within variably altered felsic volcanic rocks of the Nepisiguit Falls and Flat Landing Brook formations. These three petrographically indistinguishable iron formation intervals (Fe2O3T = 21.4 wt.%) likely represent cogenetic hydrothermal sedimentary units because they display a common geochemical signature: Fe2O3T = 42.9 ± 10.5 wt.%, MnO = 5.4 ± 3.1 wt.%, elevated base metal values (Zn+Pb = 1999 ± 1091 ppm), strong enrichment in additional exhalative components (CaO = 5.3 ± 3.9 wt.%; P2O5 = 1.43 ± 1.00 wt.%), oxidized signature (Fe/Mn = 10 ± 6), as well as a common immobile element signature (Zr/TiO2 = 0.025 ± 0.007) representative of a pelagic source. The calc-alkaline to transitional host volcanic rocks can be discriminated by Zr/TiO2, and to a lesser extent by Th/Nb: Nepisiguit Falls Formation: Zr/TiO2 = 0.053 ± 0.004, Th/Nb = 1.08 ± 0.37; Flat Landing Brook Formation: Zr/TiO2 = 0.107 ± 0.043, Th/Nb = 0.86 ± 0.17. A symmetrical repetition of the footwall-iron formation-hanging wall stratigraphic sequence is observed in DDH-B357, with distinct felsic volcanic rock domains separated by the three iron formations. This is best explained by parasitic F2 folds on the west flank of the south-plunging Brunswick antiform, similar to the fold closures known to host massive sulfide accumulations in the Brunswick No. 6 and No. 12 mines. Iron formation geochemistry and felsic volcanic rock chemostratigraphy from drill core sampling can provide an effective mineral exploration tool for the structurally complex rocks of the Bathurst Mining Camp. Sommaire - Le forage au diamant DDH-B357, situé à 1.5 km au nord du gisement de Sulfures Massifs à Encaissant Volcanique et Sédimentaire (SMEVS) de Zn-Pb-Cu-Ag Brunswick No. 6 recoupe trois horizons exhalatifs au sein des roches volcaniques felsiques diversement altérées des formations de Nepisiguit Falls et de Flat Landing Brook. Ces trois intervalles de formation de fer, impossibles à distinguer pétrographiquement les uns des autres, représentent vraisemblablement des unités sédimentaires hydrothermales cogénétiques sur la base de leur signature géochimique commune: Fe2O3T = 42.9 ± 10.5 % poids, MnO = 5.4 ± 3.1 % poids, des teneurs élevées en métaux usuels (Zn+Pb = 1999 ± 1091 ppm), un fort enrichissement en composantes exhalatives additionnelles (CaO = 5.3 ± 3.9 % poids; P2O5 = 1.43 ± 1.00 % poids), une signature oxydée (Fe/ Mn = 10 ± 6), ainsi qu’une signature d’éléments immobiles communs (Zr/TiO2 = 0.025 ± 0.007) indicative d’une source pélagique. Les roches volcaniques encaissantes calco-alcalines à transitionnelles peuvent êtres reconnues par leur rapport Zr/TiO2, et à un moindre degré par leur rapport Th/Nb: Formation de Nepisiguit Falls: Zr/TiO2 = 0.053 ± 0.004, Th/Nb = 1.08 ± 0.37; Formation de Flat Landing Brook: Zr/TiO2 = 0.107 ± 0.043, Th/Nb = 0.86 ± 0.17. Une répétition symétrique de la séquence stratigraphique Mur-Formation de Fer-Toit a été observée dans le forage DDH-B357, avec des domaines distincts constitués de roches volcaniques felsiques séparés par les trois formations de fer. La meilleure explication est que le flanc ouest de l’anticlinal Brunswick à plongée sud est affecté par des plis parasites F2, similaires aux zones de charnière contenant les sulfures massifs des mines Brunswick No. 6 et No. 12. La géochimie des formations de fer et la chimiostratigraphie des roches volcaniques felsiques en forage peuvent fournir un outil d’exploration minérale efficace dans les roches structuralement complexes du Camp Minier de Bathurst."

Jan 1, 2006

By L. R. Fyffe, D. R. Lentz, S. H. Mcclenaghan

"Abstract - The Eel River area in the southwestern Miramichi terrane of New Brunswick contains a complete calc-alkaline suite of volcanic rocks that are interlayered with intervals of sedimentary and polylithic fragmental rocks, and are overlain by a thick sedimentary sequence. This package, collectively referred to as the Meductic Group, was deposited in a submerged volcanic arc setting interpreted to be part of the Popelogan arc. Rifting of this arc led to the development of the Tetagouche-Exploits back-arc basin, and formation of volcanogenic massive sulfide deposits in bimodal volcanic rocks of the Bathurst Mining Camp in the northeastern Miramichi Terrane. Unlike the Bathurst Mining Camp, volcanic rocks in the southeastern Miramichi Highlands form a continuous calc-alkaline suite characterized by increasing Zr/TiO2 with increasing SiO2, in part resulting from progressive coupled assimilation and fractional crystallization of nested magma systems. Slumping of semi-consolidated volcanic and sedimentary rocks in topographically unstable areas resulted in numerous slumps and debris flows that are preserved throughout the Eel River area. In the early 1990s, the discovery of a large sulfide clast in a road cut along the Benton road sparked interest in the volcanogenic massive sulfide potential of the Eel River area. Subsequent drilling intersected smaller fragments, one clast of which graded 16.7% Zn, 5.6% Pb, 90 ppm Ag, and 220 ppb Au. The intersection of thin lenses of stratiform sulfides in another drillhole indicates favorable conditions for the preservation of massive sulfides. Their subsequent incorporation into synvolcanic debris flows resulted in the transport and deposition of sulfide clasts from hydrothermal vents to more distal locations. Similar to the Buchans deposits of Newfoundland, tracing these debris flows back to their source would be beneficial from an exploration perspective. Approximately 15 km to the southwest of the Eel River area, gold-bearing base metal sulfide clasts (11.1% Zn, 6.13% Pb, 0.19% Cu, 108 ppm Ag, and 1100 ppb Au) occur within intermediate-composition volcanic rocks at Monument Brook in eastern Maine. Sommaire - Le secteur d’Eel River dans le sud-ouest de la terrane de Miramichi au Nouveau Brunswick contient une séquence complète de roches volcaniques calco-alcalines interstratifiées avec des roches sédimentaires et fragmentaires polylithologiques, sous une épaisse couverture sédimentaire. Cet assemblage constitue le Groupe de Meductic, et a été déposé dans un environnement d’arc insulaire interprété comme une partie de l’arc de Popelogan. Le rifting de cet arc à mené au développement du bassin d’arrière-arc de Tetagouche-Exploits, et à la formation de gisements de sulfures massifs volcanogènes dans les roches volcaniques bimodales du Camp Minier de Bathurst dans le nord-est de la terrane de Miramichi. Contrairement au Camp Minier de Bathurst, les roches volcaniques des hautes terres du sud-est de Miramichi constituent une suite calco-alcaline continue caractérisée par un accroissement du rapport Zr/TiO2 à des valeurs croissantes de SiO2, résultant en partie de l’assimilation progressive et de la cristallisation fractionnée de systèmes magmatiques superposés. L’effondrement de roches volcaniques et sédimentaires semi-consolidées dans des secteurs topographiquement instables est à l’origine des nombreux slumps et coulées de débris qui sont préservés dans le secteur d’Eel River. Au début des années 1990, la découverte d’un large claste de sulfures le long de la route Benton provoqué un intérêt pour le potentiel en gisements de sulfures massifs volcanogènes dans les secteur d’Eel River. Des forages ont par la suite recoupé des fragments plus petits, dont un claste qui a retourné des teneurs de 16.7% Zn, 5.6% Pb, 90 ppm Ag et 220 ppb Au. Le recoupement de minces lentilles de sulfures stratiformes dans un autre forage indique des conditions propices à la préservation des sulfures massifs."

Jan 1, 2006

By Pertti Koukkari, Nagendra Tripathi, Karri Penttilä, Justin Salmine

ChemSheet is a thermodynamic multi‐phase multi‐component simulation software, which is used as an Add‐in in Microsoft Excel. In ChemSheet, the unique Constrained Gibbs free energy method can be used to include dynamic constraints and reaction rates of kinetically slow reactions, yet retaining full consistency of the multiphase thermodynamic model. With appropriate data, ChemSheet models can be used to simulate reactors and processes in all fields of thermochemistry. The presentation will cover off‐line modeling of Cu‐flash smelters and advanced thermochemical simulation coupled with on‐line process control of Cu‐Ni smelting. The presentation will describe an off‐line model of Cu‐smelter based on critically assessed properties of the Al-Ca-Cu-Fe-O-S-Si –system (slag, matte and liquid metal) by using the quasichemical model. A four‐stage reactor model (shaft, settler, uptake and bath) is used for optimizing process parameters and feed particle distribution. As a second example, an advanced thermochemical model of a Ni-Cu sulphide smelting plant will be given. The on‐line model covers the operation of treating Ni-Cu-S concentrate via roasters, electric furnace and converters, producing a high grade Bessemer matte product for further refining. The model integrates the thermochemistry of the roasters and electric furnace, and predicts important process parameters such as degree of sulphur elimination in the fluid‐bed roasters, matte grade, iron metallization, slag losses and the iron to silica ratio in the electric furnace slag. Both models can be used to assist process engineers and operators in calculating the addition rates of coke, flux and air for different feed scenarios.

Jan 1, 2014

By Arhtur T. Allen

THE Kingsport formation, a part of the Knox dolomite of Ordovician age, is composed of 538 ft of dolomite and limestone. Numerous bands, layers and nodules of chert, arenaceous and shale zones are present. The characteristics displayed by these features have been useful in mapping, prospecting and mining. Perhaps a better understanding of the origin of these zones will increase their usefulness.

Jan 1, 1947

By Stephen E. Mosher, Suzanne D. Smith

Ground, air, and water vehicles can expose humans to substantial multi-axis vibration. Multiple input/multiple output relationships or models exist for estimating frequency response functions of linear systems1, 2. These relationships have been applied by some investigators to evaluate the effects of occupied seat vibration3, 4. Using a multiple input/single output model, this study investigated the effects of single- and combined-axis vibration in the fore-and-aft (X), lateral (Y), and vertical (Z) directions on vibration transmission to the human chest. Frequency response functions (transmissibilities) were estimated and compared for the back-on and back-off postures. Methods A rigid seat with seat back was mounted onto the Six Degree-of-Freedom Motion Simulator (SIXMODE). A flat acceleration vibration signal was generated between 2 and 40 Hz at 1.0 ms-2 rms in the single and combined X, Y, Z, XY, XZ, YZ, and XYZ axes. The signals were shifted in time so that the combined inputs were not fully correlated. Lightweight triaxial accelerometers were used to measure accelerations at the seat base (input) and at the bony manubrium of the chest (output). The maximum of nine frequency response functions (H(?)) or transmissibilities were estimated from the auto- and cross-spectra. The system transfer matrix for the XYZ inputs and chest Z output is [ ] where PxZ, PyZ, and PzZ are the cross-spectra between the three inputs at the seat base and the Z output at the chest, respectively, and Pxx, Pxy,…zz are the auto- and cross-spectra between the input signals (? not shown in Eq. 1). Equation 1 can be similarly written for the chest X and Y outputs. Matlab® was used to estimate the auto- and cross-spectral densities for calculating the transmissibilities, ordinary coherences (for single inputs), partial coherences, and multiple coherences. Results Figure 1 illustrates the major chest transmissibilities observed for the two postures. Vertical vibration showed a consistent influence on the chest X response (Chest X/Z), most likely causing chest pitch. Some chest Z responses were observed with X-axis inputs, but the results were variable and difficult to interpret. In general, other factors besides the known inputs did not affect the transmissibilities shown in Figure 1 (Repeated Measures ANOVA, P<0.05). This was

Jan 6, 2006

By AIME AIME

WITH a membership in the Institute of 32 years behind him, Chester Alan Fulton became an A.I.M.E. Director last month. In 1937 he served as Chairman of the Industrial Minerals Division. Mr. Fulton was born in Brooklyn on Dec. 18, 1853, and at the age of 22 graduated from the Columbia School of Mines. His first job was as assayer for the Standard Smelting Co., Rapid City, S. D., but he soon left to become shift boss in the cyanide plant of the Peregrina Mining & Milling Co., Guanajuato, Mexico. From 1908 to 1912 he was mine superintendent of the Guanajuato Mining & Milling Co., leaving there for two years of varied professional work. From 1914 to 1916 he was

Jan 1, 1939

By AIME AIME

NATURE was in a smiling mood on December 18, 1883. On that day, Chester Alan Fulton, the sixty-first President of the American Institute of Mining and Metallurgical Engineers, was born, and she endowed him with every good quality within her reach - looks, physique, intelligence, and character. Brought up in the valley of the Hudson River, with the mighty Palisades which make it the "Rhine of America," he has lived up to his early promise - as a man, as an engineer and as a friend.

Jan 1, 1943