Search Documents

By S. Whinery

I am indebted to L. E. Bryant, of Danville, Ky., President of the Virginia Mining Co., operating coal-mines in Scott county, Tenn., for the following information relating to the existence of the Clinton iron-ore under the NW. slope of the Cumberland Plateau in Kentucky and Tennessee. During the past 15 years quite an important oil-field has been developed in a region having Wayne county, Ky., as its center, and a large number of wells have been drilled in that and adjacent territory in the search for oil. Many of these wells have been carried to considerable depths below the recognized oil-bearing horizon, and one of them was drilled by Mr. Bryant at Pine Knot, a station on the Cincinnati, New Orleans & Texas Pacific railroad, a few miles north of the point where that road crosses the Kentucky-Tennessee State-line. The elevation of

Jan 1, 1913

By John S. Alexander

The typical block coal of the Brazil (Indiana) District differs in chemical composition but little from the coking coals of Western Pennsylvania. The physical difference, however, is quite marked; the latter has a cuboid structure made up of bituminous particles lying against each other, so that under the action of heat fusion throughout the mass readily takes place, while block coal is formed of alternate layers of rich bituminous matter and a charcoal-like substance, which is not only very slow of combustion, but so retards the transmission of heat that agglutination is prevented, and the coal burns away layer by layer, retaining its form until consumed. This property permits the use of raw block coal in the furnace but theo-

By Frank Firmstone

It is proposed to consider here only comparisons made between results obtained when the materials employed are precisely the same, two furnaces at the same works for example, or the same furnace under different conditions as respects temperature of blast, method of charging, etc. With this limitation, the most important point in the comparison is the amount of fuel consumed per ton of iron. This, in fact, is the only item in the prime cost of the iron which can properly be said to vary in consequence of changes in the furnace process; for of the other principal items, the ore used per ton of iron, and also the amount of fluxing material, will depend on its richness, which, under the assumed conditions, will be practically invariable when taken over any considerable period; the labor cost also, from its nature, should be very nearly constant when estimated on the ton of iron. Moreover, as it consists principally in handling and moving material, it is greatly affected by circumstances quite independent of

By Cyril S. Taylor, Junius D. Edwards

Magnesium is the lightest metal used for structural purposes, for which reason perhaps more than usual interest is attached to measurements of its density. Although the density of solid magnesium has been det,ermined frequently, no measurements of the density of the liquid metal are available. Because of unusual experimental difficulties in measuring the density of the liquid, only a limited number of measurements of good precision were secured. The results, especially the value for the crystallization shrinkage, are of great interest in connection with the casting of the metal. A number of samples for these measurements were made available through the courtesy of the American Magnesium Corp. They were in the form of extruded bars 3/8 in- in diameter and several were of exceptional purity, as indicated by careful analyses. Table 1 gives the density values (at 20" C.) for magnesium of varying degrees of purity. The density was measured at room temperature by comparison of the weight in air, and when immersed in distilled water. The necessary buoyancy corrections were applied, so that the density could be expressed in absolute measure—grams per milliliter. The effect of the buoyancy of the immersed suspension and the surface-tension pull of the water upon the suspension were eliminated from the results by a preliminary weighing of the suspension immersed to the working depth. Great care was necessary to prevent the introduction of a significant error by the formation of gas bubbles upon the clean magnesium surfaces; these are sometimes very minute and easily escape observation. They may be detached by raising the specimen from the water and again immersing; this should be done just prior to completing the weighing. Their formation may be almost entirely prevented during a measurement by previously immersing the specimen in a solution of paraffin in petroleum ether. The thin film of paraffin remaining after the evaporation of the solvent prevents wetting of the magnesium surface by the water. In one such determination, the paraffin coating on a 22-gm. Specimen

Jan 1, 1923

By Junius D. Edwards, Cyril S. Taylor

Magnesium is the lightest metal used for structural purposes, for which reason perhaps more than usual interest is attached to measurements of its density. Although the density of solid magnesium has been det,ermined frequently, no measurements of the density of the liquid metal are available. Because of unusual experimental difficulties in measuring the density of the liquid, only a limited number of measurements of good precision were secured. The results, especially the value for the crystallization shrinkage, are of great interest in connection with the casting of the metal. A number of samples for these measurements were made available through the courtesy of the American Magnesium Corp. They were in the form of extruded bars 3/8 in- in diameter and several were of exceptional purity, as indicated by careful analyses. Table 1 gives the density values (at 20" C.) for magnesium of varying degrees of purity. The density was measured at room temperature by comparison of the weight in air, and when immersed in distilled water. The necessary buoyancy corrections were applied, so that the density could be expressed in absolute measure—grams per milliliter. The effect of the buoyancy of the immersed suspension and the surface-tension pull of the water upon the suspension were eliminated from the results by a preliminary weighing of the suspension immersed to the working depth. Great care was necessary to prevent the introduction of a significant error by the formation of gas bubbles upon the clean magnesium surfaces; these are sometimes very minute and easily escape observation. They may be detached by raising the specimen from the water and again immersing; this should be done just prior to completing the weighing. Their formation may be almost entirely prevented during a measurement by previously immersing the specimen in a solution of paraffin in petroleum ether. The thin film of paraffin remaining after the evaporation of the solvent prevents wetting of the magnesium surface by the water. In one such determination, the paraffin coating on a 22-gm. Specimen

Jan 1, 1923

By R. C. Canby

The American water-jacket furnace is the outgrowth of lead-smelting at Eureka, Nev., subsequently developed in Utah and Colorado. Early smelting in Virginia, New England, or the Missouri-Kansas-Illinois district seems to have had no direct influence in the development of this furnace. First Decade, 1870 to 1880. In 1870, the draft-furnace was used in Nevada, coincidentally with the first crude sandstone blast furnaces, which were 2 or 3 ft. sq., with Sturtevant fans or small Roots blowers, and sheet-iron or water-cooled tuyeres. Stetefeldt, Liebenau, Albert Arents, and 0. H. Hahn mere the early metallurgical leaders. Arents's siphon-tap and the re-establishment of the furnace-bosh mere the most important improvements of the decade. Second Decade, 1880 to 1890. At first there were ,many small local plants; but by the time Eureka had reached its maximum production of lead-ore, two custom works (the Eureka and the Richmond) were treating all the ore, the miners having learned the economy of smelting at larger and well-constructed plants. In the early eighties, most of the features of modern practice were already discernible at Salt Lake, Leadville, Denver, and Pueblo. The small square sandstone furnaces had been replaced by rectangular water-jacket furnaces, mostly 36 in. wide, and from 60 to 80 in. long at the tuyeres, which entered between cast-iron water-jackets. Subsequently, Franz Casin, at the Holden works, Denver, put the tuyeres in the middle of the jackets, and many other improvements were made by him and others, so that the cast-iron jacket became the favorite, until the possibility of

Jan 1, 1913

By Ernst F. Eurich

Alexander Parkes patented in England in 1851-52-53 a process for desilvering lead by means of zinc, making use of the greater affinity of silver for zinc than for lead, discovered by Karsten in 1842. The efforts in England to develop it commercially were not particularly successful, nor was the attempted introduction into the United States. This last was not surprising, as it was about the beginning of our Civil War, and at that period there was very little lead-bullion produced in the United States and there was no field for the process here. There was at that time on Staten Island an establishment that pattisonized lead, probably from Rossie, N. Y., and Chester, Pa., and possibly some Spanish lead, but the production of lead-bullion in the Far West had not yet begun. In 1864, Edward Balbach, of Newark, N. J., patented in this country a process for desilvering lead by means of zinc, and in 1867 Edward Balbach, Jr., patented a " movable black-lead retort with a neck, placed in a furnace," for the purpose of distilling the alloy of zinc, lead, and the precious metals. A brief comparison of the Parkes and the Balbach processes is interesting. The Parkes process as practiced in England consisted in stirring into silver-bearing lead, melted in a kettle, from 1 to 2 per cent. of zinc, cooling, skimming the alloy of lead, zinc, and silver that rose to the surface, liquating it in an iron retort, distilling the residual rich alloy in fire-clay retorts, thus regaining the zinc, and refining the desilvered lead at a low heat in a shallow cast-iron pan that formed the hearth of a reverbera-tory furnace. If the lead was too impure, it was first softened

Jan 1, 1913

By Charles H. Eldridge, Robert J. Anderson

When a metal or alloy is poured into a mold, internal stresses are set up by the cont,raction in volume on passing from the liquid state at the temperature of pouring to the solid state at the ordinary temperature. It is assumed by the writers that all castings are internally stressed. That any casting is internally stressed is shown by its warping or distortion on maturing at the ordinary temperature, by warping or cracking on heating, or by cracking or distortion on machining. In the investigation made by the writers, the internal stresses in cast non-ferrous alloys were studied with a view to examining the effects of heat treatment (i.e., simple anneal) on the release of such stresses. Data have been obtained that show quantitatively that internal stresses can be removed by appropriate heat treatment. The investigation was limited to a study of the effect of heat treatment on stress release in cast rings of the 87:7:5:1 copper-tin-zinc-lead alloy. The writers are indebted to E. G. Fahlman for the method used for inducing stress in cast rings; to M. E. Boyd for microscopic examination and for other aid; and to G. B. Dalrymple for the chemical analyses. General Information While casting stresses have been discussed considerably, they have usually been treated in a general way, and so far as the writers know no measurements of the magnitude of internal stresses in castings have been reported. It has been suggested by many investigators, particularly in the case of steel castings, that castings are internally stressed, and that these stresses can be removed by annealing. In a casting, the internal

Jan 1, 1923

By Robert J. Anderson, Charles H. Eldridge

When a metal or alloy is poured into a mold, internal stresses are set up by the cont,raction in volume on passing from the liquid state at the temperature of pouring to the solid state at the ordinary temperature. It is assumed by the writers that all castings are internally stressed. That any casting is internally stressed is shown by its warping or distortion on maturing at the ordinary temperature, by warping or cracking on heating, or by cracking or distortion on machining. In the investigation made by the writers, the internal stresses in cast non-ferrous alloys were studied with a view to examining the effects of heat treatment (i.e., simple anneal) on the release of such stresses. Data have been obtained that show quantitatively that internal stresses can be removed by appropriate heat treatment. The investigation was limited to a study of the effect of heat treatment on stress release in cast rings of the 87:7:5:1 copper-tin-zinc-lead alloy. The writers are indebted to E. G. Fahlman for the method used for inducing stress in cast rings; to M. E. Boyd for microscopic examination and for other aid; and to G. B. Dalrymple for the chemical analyses. General Information While casting stresses have been discussed considerably, they have usually been treated in a general way, and so far as the writers know no measurements of the magnitude of internal stresses in castings have been reported. It has been suggested by many investigators, particularly in the case of steel castings, that castings are internally stressed, and that these stresses can be removed by annealing. In a casting, the internal

Jan 1, 1923

By Albert E. Greene

Processes for the removal of phosphorus from iron or steel are steadily assuming greater importance in view of the abundance of high-phosphorus iron-ore and the diminishing supply of pure ore. In the present methods of removing phosphorus by the basic open-hearth or basic Bessemer process, or even by electric processes, complete control over the metallurgical conditions is either impossible or has not yet been realized. The removal of phosphorus has so long been accomplished along certain well-defined lines, that when the electric furnace made its appearance metallurgists adhered to the same old reactions used in the older processes and failed to appreciate and take advantage of the new forces at their disposal. One object of the present paper is to set forth more clearly the metallurgical reactions by which phosphorus can be removed from iron, and to show the necessity of controlling the conditions, and particularly the temperature, by means other than combustion in the furnace-chamber. Invariably, the commercial removal of phosphorus has been accomplished by oxidation. The reactions involved in oxidation of phosphorus in general consist, first, of the formation of P2O5 and second, the combination of this oxide with lime, forming calcium phosphate, which latter is held in a slag high in iron oxide. In the present-used processes, the phosphorus is never removed without the assistance or presence of considerable quantities of iron oxide. The oxygen for removal of phosphorus in the basic open-hearth process comes largely through the medium of iron oxide and furnace-gases, but not

Jan 1, 1913

By George Ross Green

[In discussion of the paper of Mr. J. C. Bayles, read at the New York meeting of September, 1890, Trans., xix., p. 18.1 It is often so difficult to locate the causes of failures of machinery and apparatus which can be examined and studied at leisure, that it is not surprising that the causes of explosions should escape detection. Usually the explosion is the first evidence that anything is amiss, and the time for observing the conditions is necessarily brief. An incident in a welding-works near Essen, Germany, might be cited as exemplifying what trifling causes may lead to disaster, and how difficult, under the most favorable conditions, it may be to discover them. A blowing-engine was arranged with two suction-pipes at each end of the blowing-cylinder—one leading to the air, and the other to the gas-holder. Each pipe was provided with a valve, and all were so adjusted that the cylinder drew in gas and air in the proportions found most advantageous. The gases from the cylinder were carried directly to the furnace through suitable pipes, and while the cylinder was provided with relief-valves, every effort was made to prevent explosions, principally by compressing the gases to a point where the rate of efflux of the mixture was greater than the velocity of combustion, if the expression is here allowable. It was found that the apparatus would work satisfactorily for some time, and then the relative proportions of the mixture would change, and an explosion might have been the result. Experiments consuming days were made to discover a method of averting this danger, but they were unsuccessful, until it was observed that the change in the composition of the mixture of gas and air took place when the gasometer began to rise or fall—the back-pressure due to friction when the holder was rising or its absence when falling being sufficient to change the conditions. As soon as this was discovered,

Jan 1, 1892

By John Jermain Porter

The chief purpose of this paper is to indicate the laws governing the fuel-economy of the cupola, to examine the feasibility of some of the proposals for increasing its fuel-economy, and to show that the conditions limiting fuel-economy here are altogether different from those prevailing in the blast-furnace. The two methods available for studying the thermal efficiency of the cupola and determining the factors limiting fuel-economy are: 1, by the determination of the total heat-balance; and 2, by the application of the theory of critical temperatures. The case selected as an example represents a cupola operating under fairly efficient conditions. The data are as follows : Cupola, GO in. in diameter, 15 ft. high to the charging-door, with a 9-in. lining. Bed-charge, 2,000 lb. of coke and 4,000 lb. of iron. Subsequent charges, 400 lb. of coke and 4,000 Ib. of iron. Total number of charges, 20. There was 800 lb. of coke recovered from the drop, hence the total coke burned is 8,800 lb., or 0.11 lb. of coke per Ib. of iron. Coke contains 90 per cent. of fixed carbon and 2 per cent. of moisture. 300 1b. of kindling-wood is used in lighting. 80 lb. of limestone (95 per cent. of CaCO,) is used per charge, or 0.02 lb. per Ib. of iron. Melting-loss, 4 per cent.; distributed thus : Fe, 3.5; Si, 0.25; Mn, 0.25 per cent. Average analysis of top-gases : CO2, 15.1; CO, 10.0 per cent. Average temperature of top-gases, 1,600" F. Temperature of air and stock charged, 60" F. Dew-point of air, 50 F. The items entering into the total heat-balance and their calculation are as follows: 1. Heat of combustion of fuel.—Total heat evolved = 14,580 x lb. of carbon burned + 7,200 X Ib. of wood burned. Hence B.t.u. per lb. of iron charged =

Jan 1, 1913

By Charles E. Hall

The Crimora mine, operated by the American Manganese Company, Limited, is located 21/2 miles east of Crimora station, 011 the Shenandoah Valley railroad, in Augusta county, Virginia. It is situated in a basin at the western base of the range of mountains which flanks the Shenandoah Valley on the east. This range is composed of the Potsdam sandstone (No. I. of the Pennsylvania survey), and extends in a northeasterly-southwesterly direction the entire length of the valley. The general dip of the measures is westward. The massive sandstone of the mountain is geologically overlaid with shales or slates, which belong to the Potsdam, or lie between it and the Lower Silurian limestone. Throughout this region these shales are decomposed, and form more or less extensive clay deposits, which are found along the base of the range and often underlie a considerable area to the westward of the abrupt slope of the range. Sand and fragments of quartzite occur in considerable quantities on the surface, and often conceal the true character of the underlying formation. The area containing this ore-deposit extends northeast and south-

Jan 1, 1892

By F. A. J. Fitzgerald

In any kind of furnace the question of preventing the loss of heat is important, for no matter how the heat is obtained it costs something; and consequently, other things equal, that furnace is most desirable which uses the greatest percentage of the total heat generated for the particular object in view. In the furnace which uses electricity for the generation of heat the importance of preventing losses of heat is very much greater than in any other. To generate 1,000 kg-cal. requires an expenditure of 1.16 kw-hr., and consequently the cost per calorie is always expensive when electricity is used for heating. In heating any material in a furnace a general rule is that the generation of heat should be as rapid as possible. In any given furnace the heat-losses may be expressed as so many watts, and, therefore, the longer it takes to heat the furnace-charge the greater the losses will be. Suppose that a furnace contains a charge to be heated to 1,500°C. and that the average loss of heat is at the rate of 100 kw., then if the process of heating the charge takes 1 hr. the losses will amount to 100 kw-hr.; but if by using a more rapid generation of energy the charge can be heated in 30 min. the losses will amount to 50 kv-hr. An example from experiments on a certain process may be given to illustrate this point. The problem was simply to heat a furnace-charge to a certain temperature, and experiments were made to determine the effect of increasing the rate of generation of energy and comparing the kilowatt-hours required to heat a given charge. Here are typical results : Rate of Generation Energy Per Kg. of Energy. of product 88 kw. 1.7 kw-hr. 93 kw. 1.6 kw-hr.

Jan 1, 1913

By John W. Langley

The unsatisfactory character of most, if not all, of the processes for the direct determination of alumina in the presence of iron and phosphoric acid, and the sharpness with which both the iron and phosqhoric acid can be determined, have led chemists to rely mainly

Jan 1, 1892

By Mark A. Ammon

The two most widely used methods of measuring hardness are the Brinell and the scleroscope. In the Brinell method a hardened steel ball is pressed into the steel under a definite load and the area of the resulting depression is measured. The load in kg. per sq. mm. of the area of the depression is taken as a measure of the hardness. Within certain limits the hardness number so determined is independent of the load or the size of the ball. In the scleroscope method a small weight carrying a diamond point is dropped through a glass tube upon the steel and the amount of rebound is taken as proportional to the hard-' ness. In both methods the scale of hardness is an arbitrary one; however, they agree in a comparative may, that is, a steel showing 50 per cent. increase in hardness by the Brinell test mill show approximately 50 per cent. increase in hardness by the scleroscope test. Yet upon consideration of the two methods it appears that, upon a steel which has been carbonized, this should not be the case ; for the scleroscope method gives almost exclusively the surface-hardness, and the condition of the material below the surface has but a slight bearing upon the hardness number. The results given by the Brinell method should, however, be the exact opposite; for the depth of penetration 'of a ball pressed into the steel would be dependent to a large extent upon the condition of the material below the surface. This is particularly obvious when it is considered that the size of the ball ordinarily used in the Brinell method is 1 cm. (about 8 in.) in diameter under a load of 3,000 kg., while the diamond point of the scleroscope is in the neighborhood of 0.01 in. across, fitted in a hammer of about 0.5 oz. weight and dropping from a height of 10 inches.

Jan 1, 1913

By R. Moldenke

Unlike the furnaces employed in the reduction of ores to mattes and metals, the foundry-cupola has only melting to do. This looks simple enough; and its development has progressed through centuries by cut-and-try methods; but there is still much to be learned concerning the causes which underlie the production of defective castings, even from first-rate materials. There are other differences between the smelter and the cupola. The former is usually, the latter rarely, run continuously. In the smelter there is some chance for experiment, since rich slags can be treated again; while in the cupola the metal must be good for casting from the first tap to the drop of the bottom ; otherwise, heavy damage will result. In the smelter, the object sought is the production of metal or matte with a minimum loss in the slag; whereas, in the foundry, a variety of castings of different compositions must often be run from the same heat, one after the other. Experience with the cupola has shown that the melting should take place, throughout the heat, in one zone, the zone of maximum temperature, which is clearly marked on the cupola-lining by the severe cutting action of the slag and iron oxide. The design and operation of the cupola must conform to this condition. This conformity having been secured, other considerations resolve themselves into those details of construction which will involve least trouble and cost of repairs. The very high temperatures required to melt iron and steel in the cupola, leaving the metal sufficiently superheated for casting, render the use of water-jackets inadvisable. It is always possible to patch up the lining at the melting-zone between daily heats; and the rest of the lining is seldom affected enough by abrasion and chemical action to require replacement oftener than once in nine months. The cupola is practically a shell of steel, lined with the proper refractory material, and provided with a sct of tuyeres for the admission of air to burn the fuel and melt the metallic

Jan 1, 1913

By P. Barnes

Exact accounts hare been kept of the cost of these chimneys, and it may he a matter of some possible interest. that the plans and details of cost should be laid before the Institute. The statement of cost herewith submitted does not give minute particulars of the weights or quantities of material used, although these are noted upon the company's books.

By H. F. Miller

Fox some years the prejudice against basic open-hearth steel for casting has been gradually decreasing. Yet many consumers and engineers still cling to acid steel for castings, because of their alleged greater freedom from blow-holes and sponginess. Acid steel has been used for this purpose much longer than basic steel; and the melters in acid practice had it well in hand when basic steel was first tried. Then the necessity of learning a new set of laws for the production of satisfactory basic open-hearth steel for castings became evident. The first of these laws, in my opinion, has to do with the furnace construction. The heat should be melted down as speedily as possible so as to prevent excessive oxidation. I have described in another article ' some furnaces designed by me, and having as one of their features the promotion of quick melting. Size of the Furnace. The hearth of the furnace, however, is a decisive factor in the production of solid castings. The manufacturer should know the size of the heats he intends to make constantly, and should have his furnace built for that size of heat. The hearth should differ in dimensions from that of a furnace making ingotr steel. That is, the bath should be deeper and should have less surface-area. A shallow bath permits the slag to come out soon after the steel commences to flow, and thus prevents the additions from going into the steel, or from becoming uniformly distributed in case they have been put in hurriedly. Under this head comes the very poor practice of making small heats in hearths of a much larger capacity. If into a 25-or 30-ton furnace only 12 or 15 tons of metal is charged per heat, the proportion of heats that will be wild, or show signs

Jan 1, 1913

By G. A. Reinhardt, Albert Sauveur

Although many metallurgists know that some pearlitic special steels can be made troostitic, martensitic, and even austenitic, without quenching, and, therefore, without exposing them to the dangers of the quenching-bath, the practical significance of such possibility does not seem to have received the attention it deserves. Let us recall briefly the mechanism of the transformation alluded to. In Fig. 1 (after Guillet) is shown the constitutional diagram of nickel-steel; that is, of alloys of iron, carbon, and nickel. Any steel the composition of which falls within the area LPO is pearlitic after slow cooling; any steel the composition of which is represented by a point within the area MLO is martensitic, and any steel within the area MNO is austenitic. Starting with pearlitic steel, then by increasing the carbon-content or the nickel-content, or both, the metal becomes marten-sitic and eventually austenitic; that is, its composition crosses first the boundary-line LO and then the line MO—and it remains martensitic or austenitic after slow (air) cooling.' We have in this way imparted to the metal without quenching it the properties of hardened carbon-steel. In other words, the steel is now self-hardening; Nickel cannot be introduced into solid steel, but by the well-known process of case-hardening it

Jan 1, 1913