Search Documents

By P. D. Rao, H. B. Charmbury, D. R. Mitchell

As a result of a changing market pattern for anthracite, there is now an increasing demand for steam size and a decreasing demand for domestic sizes. To help the producer meet this new demand, the authors present the technical aspects of the problem of crushing domestic sizes to steam fineness and size. The market pattern for anthracite coal has changed considerably in recent years. The demand for domestic sizes has been gradually decreasing and the demand for the steam sizes has been increasing. The companies however aim for a maximum production of domestic sizes, since these sizes command premium prices. To meet the market demands, particularly in certain periods of the year, further size reduction of the coarse clean coal is necessary. The present practice of multistage crushing in toothed rolls leads to complicated flow arrangements and is high in cost. Data presented herein indicate that crushers with high reduction ratios could be used with a resulting simplification of crushing flows and an appreciable reduction of capital and operating costs. The different types of crushing equipment investigated included the rotary-type breaker, the jaw crusher, the impactor-type crusher, and the Aerofall mill. CURRENT PRACTICE The standard sizes of anthracite are presented in Table I and market specifications require that any given size be maintained with only a limited amount of oversize and undersize material. The 1958 prices of the various sizes also are presented, so it may be seen that size reduction is only performed when dictated by market demands. At the present time the general practice of crushing anthracite consists of removing the top size and crushing it in a toothed double roll crusher to the next largest size. Consequently, to reduce the domestic egg, stove, and nut sizes to steam sizes of pea, buck, rice, and barley, the original material must be screened to produce the three top sizes and each size must be crushed in three separate rolls to the next largest size. Each crushed product must then be rescreened to remove the oversize for re crush ing. Thus a typical operation would consist of scalping the egg size from a mixture, crushing it to stove size, and rescreening the product. This same cycle would be repeated for the stove and nut sizes requiring three screens and three crushers as well as conveying equipment to handle the crushed products. This results in an expensive series of operations to make a product which sells for a lower price. If the three top sizes are crushed in one operation to the smaller sizes then the yield of steam sizes is low and the production of Nos. 4 and 5 sizes is large. These sizes sell for lower prices than the steam sizes. A typical operation is presented in Fig. 1. From the figure it may be seen that the original cleaned anthracite contains 67.4 pet domestic sizes, 26.4 pct steam sizes, and 6.2 pct fines. After multistage crushing of the domestic to steam sizes the composition of the product is 0.6 pct domestic sizes, 89.6 pct steam sizes, and 9.8 pct fines. From a technical standpoint these results are reasonable but the handling and crushing costs are

Jan 1, 1961

By H. E. Criner, M. G. Driessen

THE cyclone thickener has two important applications in wet washing plants: (1) water clarification, and (2) fine coal recovery. The thickener consists of a conical chamber into which the fluid is injected through a tangential nozzle at the periphery of the large end. The solids of the slurry are concentrated and removed from the apex of the cone while the "thinner" portion is discharged from a central tube in a flat head at the large end, fig. 1. The advantages of the cyclone thickener are that large volumes of slurry may be treated with small space requirements and that the underflow concentration may be controlled easily and readily to meet varying feed conditions. Control of Washery Water Solids Concentration: The first requirement, in the process of controlling solids concentration, is that the solids be removed from the body of circulating water at the rate at which they are introduced. If this condition is satisfied the concentration will remain at a fixed value and will not increase to uncontrollable levels. The second requirement is that the solids concentration

Jan 1, 1951

By M. G. Driessen, H. E. Criner

THE cyclone thickener has two important applications in wet washing plants: (1) water clarification, and (2) fine coal recovery. The thickener consists of a conical chamber into which the fluid is injected through a tangential nozzle at the periphery of the large end. The solids of the slurry are concentrated and removed from the apex of the cone while the "thinner" portion is discharged from a central tube in a flat head at the large end, fig. 1. The advantages of the cyclone thickener are that large volumes of slurry may be treated with small space requirements and that the underflow concentration may be controlled easily and readily to meet varying feed conditions. Control of Washery Water Solids Concentration: The first requirement, in the process of controlling solids concentration, is that the solids be removed from the body of circulating water at the rate at which they are introduced. If this condition is satisfied the concentration will remain at a fixed value and will not increase to uncontrollable levels. The second requirement is that the solids concentration

Jan 1, 1951

By H. E. Criner, M. G. Driessen

Maurice Rey—The influence of cyclone diameter upon the fineness of separation is an important point which, however, cannot be discussed adequately if the injection pressure or the rate of flow are not specified. Perhaps some light can be thrown on the matter by using the formulas derived by Dahlstrom. Let us consider several geometrically similar cyclones where the apertures e and b are equal and proportional to the diameter D and which are operated with the same pressure drop. Eq 8 of Dahlstrom's paper can be written: Q Q = K D'. " or. if F is constant: Q = K D18 K is a constant of proportionality. Introducing this value of Q in eq 13 gives elimination efficiency = K D ,41 Elimination efficiency, in the terminology of Dahl-strom, means the diameter of particles, in microns, which divide equally between the underflow and the overflow. This denomination is regrettable and it would be preferable to call it diameter of separation or characteristic size or any other name connoting a size rather than an efficiency. Whatever the name used, the above equation shows a slow increase in the fineness of separation when the diameter of the cyclone decreases. For example, if a 14-in. cyclone gives a 400-mesh separation (37 microns), geometrically similar cyclones, having the same pressure drop will give separations at the sizes shown below.

Jan 1, 1951

By M. G. Driessen, H. E. Criner

Maurice Rey—The influence of cyclone diameter upon the fineness of separation is an important point which, however, cannot be discussed adequately if the injection pressure or the rate of flow are not specified. Perhaps some light can be thrown on the matter by using the formulas derived by Dahlstrom. Let us consider several geometrically similar cyclones where the apertures e and b are equal and proportional to the diameter D and which are operated with the same pressure drop. Eq 8 of Dahlstrom's paper can be written: Q Q = K D'. " or. if F is constant: Q = K D18 K is a constant of proportionality. Introducing this value of Q in eq 13 gives elimination efficiency = K D ,41 Elimination efficiency, in the terminology of Dahl-strom, means the diameter of particles, in microns, which divide equally between the underflow and the overflow. This denomination is regrettable and it would be preferable to call it diameter of separation or characteristic size or any other name connoting a size rather than an efficiency. Whatever the name used, the above equation shows a slow increase in the fineness of separation when the diameter of the cyclone decreases. For example, if a 14-in. cyclone gives a 400-mesh separation (37 microns), geometrically similar cyclones, having the same pressure drop will give separations at the sizes shown below.

Jan 1, 1951

By J. Mason

In order that the use of continuous mining machines be most economic, the equipment must be operated at rated capacity as much of the time as possible and downtime for repairs kept at a minimum. A large factor influencing any proposals for maintenance programs is the complexity of the machines—often the intricacies of the precision-built equipment requires engineering knowledge byond the scope of mine maintenance personnel. A training program is part of the answer; there are others. In addition to investigating a joint company-manufacturer equipment-design improvement program, Mountaineer Coal Co. has launched a detailed preventive maintenance program to combat extensive downtime often encountered when continuous miners are used. Everyone in the coal industry knows the importance of operating continuous miners at their rated capacity as much of the time as possible. The potential capacity of the miner is such that l-min. delay means from 3 to 8 tons of coal lost. Today's miner is a well designed, precision-built machine, complicated with hydraulic and electrical equipment and complex mechanical assemblies with all possible combinations of gears, levers, and rods. As the machine becomes more complex, the problem of maintenance becomes more acute. The transition from conventional to continuous mining has taken place so rapidly that the mine mechanic has been unable to keep pace. When there is a machine failure, the maintenance man usually employs either the trial-and-error or the play -it-by-ear method of repair, but this represents an expensive proposition. Mine mechanics, maintenance superintendents, and mine managers complain about the complexity of the machines and how difficult it is to keep them running. There is no shortage of skill in the design offices. Machines are designed by good engineers, but for engineers. What's the answer? Better trained maintenance men—better maintenance instruction—better field service. These are all good corrective measures, but the real cure is to provide for the men at the do it level. Designers have got to cooperate with men to simplify maintenance on the increasingly complex machine. The designer must be aware of how his machine can be maintained. Sometimes a simple design change in a bearing, oil seal, or a bushing will correct recurrent breakdowns. Parts such as filters, hydraulic cylinders, hoses, and pivot pins can be better arranged on the machine to make them accessible so that the mine mechanic can easily keep the machine producing. Therefore, to get our maintenance off on the right foot, the program must begin back in the design office, before the machine is delivered to the mine property. Realizing the importance of this aspect, our company set out on a joint company-manufacturer equipment-design improvement program. This is a formal program in which quarterly reports are written covering machine defects, design weakness, and general problems relating to machine maintenance and performance. The manufacturer in turn comments on each and every item appearing in these reports, indicating the action he proposes to take. In addition to the written reply, meetings are scheduled with manufacturer representatives to discuss further the outlined problems. The benefits realized from this organized program are both substantial and far reaching. Good maintenance begins with a good design. The subject of preventive maintenance is not a new one. Volumes have already been written on the subject. It consists primarily of doing the maintenance work when you want to rather than when the machine demands it. However, a preventive maintenance program can be overdone. Theoretically, if carried to ridiculous extreme, all working time could be spent inspecting and repairing the machines and no time would be left for production output. Our goal in maintenance is to maximize running time for all machines, and to prevent or at least minimize production downtime. INSPECTION AND REPORTING The center of any preventive maintenance schedule is regular and systematic inspection, but it must be

Jan 1, 1961

By G. H. Gronhovd, W. H. Oppelt

Complete gasification to produce synthesis gas for manufacture of synthetic chemicals and fuels offers possibilities for utilization of the vast lignite fuel deposits in the U.S. The design of a slugging, fixed-bed, pressure gasification pilot Plant is described. Results are presented for initial operation of the plant at moderate pressure and using low-temperature char as fuel. Gasification of solid fuels is becoming increasingly important in the future overall energy picture, both in this country and abroad. Snythesis gas from gasification of coal consists chiefly of carbon monoxide and hydrogen, and after suitable purification and modification this gas can be used in the production of synthetic ammonia, methanol, higher alcohols, and synthetic liquid fuels, or as a reducing gas in the metallurgical field.' Most synthesis gas used in this country is made from natural gas, petroleum oils, and refining tail-gases, but the direct gasification of coal will become more attractive as costs of petroleum oils and natural gas increase.' A gasification process designed for use with brown coal and lignite was developed by the German Lurgi Co. prior to World War 11. In this process a fixed bed of lump-sized fuel is gasified with steam and oxygen at pressures ranging from 370 to 440 psi. Effective heat exchange between the ascending high-temperature gases and the descending solid fuel results in low gas outlet temperatures, high thermal efficiency, and favorable oxygen consumption. Lurgi gasifiers are used commercially for the production of synthesis gas or as a substitute for coal gas in many countries, including Germany, Czechslovakia, Great Britain, South Africa, Australia and Pakistan.3-6 The chief disadvantage of the conventional Lurgi gasifier which operates under nonclinkering conditions is that large quantities of excess steam must be supplied with the oxygen-steam mixture to reduce the temperature in the fuel bed below fusion temperature of the ash. Most of the steam leaves the gasifier undecomposed with the product gas and, after cooling, produces large amounts of dilute liquor. Evaluation of fixed-bed gasification experiments using dry-ash removal indicated that by increasing the oxygen concentration in the oxygen-steam blast the temperature in the combustion zone could be raised high enough to operate under slagging conditions. 7-8 Operation of a fixed-bed pressure gasifier under slagging conditions would reduce the steam requirements and the volume of waste liquor and would increase the steam decomposition, the overall thermal efficiency of the process, and the rate of gas production per unit cross sectional area of the gasifier. Because the Lurgi gasification process, modified for slagging operation, offered possibilities for efficient gasification of American lignite, the Bureau of Mines decided to investigate the process on a pilot-plant scale at the Grand Forks, N. D., Lignite Research Laboratory. DESIGN Description of Pilot Plant: A flowsheet of the Grand Forks slagging gasification pilot plant is presented in Fig. 1. The gasifier unit consits of the coal lock, the gas generator, and the slag lock. The fuel, which is periodically charged to the coal lock, moves by gravity flow into the generator and is continuously gasified by an oxygen-steam mixture introduced at the bottom of the gasifier. Molten slag is formed at the hearth and flows through a central taphole into a water quench bath. The slag-water slurry is periodically discharged from the slag lock. Process steam is generated and superheated in separately-fired, oil-burning units. Oxygen is supplied to the gasifier from a gas storage bank located some distance from the pilot plant. The capacity of the oxygen storage bank is about 130,000 standard cu ft at 2200 psig. Liquid oxygen is delivered by truck and is converted to gas during the filling operation. The superheated steam and oxygen are metered separately, then mixed and fed to the gasifier tuyeres. The gas generator is surrounded by a water jacket. The steam formed is separated in the steam drum and then discharged to the gas offtake, thus equaliz-

Jan 1, 1961

By G. E. Keller

In connection with the work of Committee D5, Coal and Coke, of the American Society for Testing and Materials in developing new standards and improving old standards, series of tests were made to check the variance of sample preparation and analysis of American coals. Table I in the "Tentative Method of Preparing Coal Samples for Analysis - 02013-62T" is rather complicated, and the tests were designed to develop data for the simplification of this table. An allowance of 20% of the total variance of sampling and analysis for the sample preparation and analysis steps was used. Also, instead of coals being grouped into ash ranges, they were grouped as washed and raw (unwashed) coals. As a result of these tests, a simplified Table I for Tentative Standard 02013 has been proposed. A standard test for laboratories to check their variance of sample preparation and analysis has been developed. Committee D5 on Coal and Coke of the American Society for Testing and Materials has been making a study of all standards applying to coal for the purpose of improving and bringing them up to date and for breaking some of the existing standards covering a number of tests into single standards. As an illustration, sample preparation is now partly covered in ASTM Designation D492-48, Sampling Coals Classified According to Ash Content, and partly in ASTM Designation D271-58, Laboratory Sampling and Analysis of Coal and Coke. The latter contains, in addition to parts of sample preparation, methods for determining Moisture, Ash, Volatile Matter, etc. Although revision of sampling methods and sample preparation methods are now assigned separately, it is possible that they may end up as one standard. One of the first new Tentative Standards developed as the result of these studies was ASTM Designation D2013, Tentative Method of Preparing Coal Samples for Analysis. Although this method is quite an im- provement over that in the old standards and gives very specific instructions, Table I (attached) is quite complicated and rather hard to understand. In order to take advantage of reduced quantities or weights, it is necessary to know the ash content within rather narrow limits before sample preparation and no distinction is made as to whether the coal is cleaned or uncleaned. No limits of accuracy are assigned to the sample preparation and analysis. The total over-all accuracy of sampling, preparation and ash determination as given in D492-48 has been specified for commercial sampling procedure as follows: "This procedure is intended for an accuracy such that if a large number of samples were taken from a single lot of coal, the test results in 95 out of 100 cases would fall within ? 10 per cent of the average ash content of the sample." Although Appendix 11, Method for Determining the Over-All Variance of Reduction and Analysis in the Tentative Methods for Mechanical Sampling of Coal, ASTM Designation D2234-63T, does give a method for determing the over-all accuracy of preparation and analysis expressed as variance and also the F test, it does not permit the determination of the variance at the various stages of reduction or of the ash determination. It was decided in 1961 to ask a number of laboratories to run a series of tests for the purpose of determining the variance at various stages of reduction and analysis with the view of simplifying Table I of the Tentative Standard D2013-62-T. This paper is a record of this series of tests with recommendations which resulted from the tests. At the same time and preceding these tests the International Organization for Standardization under Committee TC/27 WG 7 was studying the same problem. Tomlinson1 of England and Dr. paul2 of West Germany had made studies giving quite a bit of information. Also Schwerd and coryel13 published some information which was the main basis for the Mechanical Division provision in ASTM Tentative Standard D2013-62T, Table I. In checking with the various laboratories which offered to cooperate in these tests, none was found which used mechanical division through the entire preparation procedure. It was then decided to use riffles at all stages with the thought that if riffles gave satisfactory variances, approved mechanical

Jan 1, 1965

By C. E. Lesher

THE Disco* process for the production of low temperature coke and its immediate predecessor, the Wisner or Carbocite process have been described in the voluminous literature of low temperature carbonization.1 This paper will describe the development of the process from the first attempt at commercial operation by the American Gas and Electric Co. at Philo, Ohio, Yn the 1920's to the successful operation in 1949 by the Disco Co., a division of the Pittsburgh Consolidation Coal Co., of the 1000-ton per day Disco plant near Pittsburgh, see Figs. 1-2. In the 1924 coal industry depression following the hectic post World War I expansion, the northern Appalachian, unionized bituminous coal fields were affected first and foremost, and Western Pennsylvania as hard as any. Competitive market pressure was heaviest on the lower grades of steam coals, notably the from the Panhandle district where ash and sulphur are inherently higher than in the same Pittsburgh coal bed to the east along the rivers. The firm structure of Panhandle coal while favoring the prepared sizes, depressed the usefulness and value of the finer sizes. Panhandle slack and nut slack were marketed with difficulty at consistent, and at times considerable, loss. Many solutions were suggested, and the Pittsburgh Coal Co. investigated all. Lower delivered prices through lower mine costs and more advantageous freight rates were obvious goals, but equally obvious were the difficulties of self attainment of either in any substantial measure. Selling Btu's in pipes was abandoned as an idea after a thorough study of the economics of distribution of what was then, and is even now, the only developed continuous process of complete gasification of bituminous coal-producer gas. Although the coal company purchased huge blocks of electric power, it sold not a car of coal to the central power stations. Public utilities controlled the markets for electric current, and it was found that no matter at how low a cost current might be put on the bus bars by the coal company, distribution to its widely scattered coal mines made such an enterprise practically impossible. Consolidation of underground operations and a huge modernization program of mining operations in the 1920's were but preparation for the introduction of mechanical cleaning of the coal for market, particularly the smaller sizes of steam, gas, and by-

Jan 1, 1953

By C. E. Lesher

THE Disco* process for the production of low temperature coke and its immediate predecessor, the Wisner or Carbocite process have been described in the voluminous literature of low temperature carbonization.1 This paper will describe the development of the process from the first attempt at commercial operation by the American Gas and Electric Co. at Philo, Ohio, Yn the 1920's to the successful operation in 1949 by the Disco Co., a division of the Pittsburgh Consolidation Coal Co., of the 1000-ton per day Disco plant near Pittsburgh, see Figs. 1-2. In the 1924 coal industry depression following the hectic post World War I expansion, the northern Appalachian, unionized bituminous coal fields were affected first and foremost, and Western Pennsylvania as hard as any. Competitive market pressure was heaviest on the lower grades of steam coals, notably the from the Panhandle district where ash and sulphur are inherently higher than in the same Pittsburgh coal bed to the east along the rivers. The firm structure of Panhandle coal while favoring the prepared sizes, depressed the usefulness and value of the finer sizes. Panhandle slack and nut slack were marketed with difficulty at consistent, and at times considerable, loss. Many solutions were suggested, and the Pittsburgh Coal Co. investigated all. Lower delivered prices through lower mine costs and more advantageous freight rates were obvious goals, but equally obvious were the difficulties of self attainment of either in any substantial measure. Selling Btu's in pipes was abandoned as an idea after a thorough study of the economics of distribution of what was then, and is even now, the only developed continuous process of complete gasification of bituminous coal-producer gas. Although the coal company purchased huge blocks of electric power, it sold not a car of coal to the central power stations. Public utilities controlled the markets for electric current, and it was found that no matter at how low a cost current might be put on the bus bars by the coal company, distribution to its widely scattered coal mines made such an enterprise practically impossible. Consolidation of underground operations and a huge modernization program of mining operations in the 1920's were but preparation for the introduction of mechanical cleaning of the coal for market, particularly the smaller sizes of steam, gas, and by-

Jan 1, 1953

By R. J. Grace

Primarily, this report presents the results of direct efficiency tests which were conducted on the 200-hp Coal-Pak, hot water generator, No. 3 unit, at the Otterbein College heating plant in Westerville, Ohio. Also included is a comparison of fuel consumption of the old plant with that of the new plant, a comparison of efficiencies obtained by the indirect method on a 300-hp Coal-Pak, and the cost of gas vs coal to show the savings effected by the latter. Tests were conducted with ten different bituminous coals selected by Mr. S. A. Frye, business manager at Otterbein College. The coals, of ten different suppliers, from four different states and eight different seams, represented competitive products economically available to the heating plant. The tests were conducted by the usual plant personnel which consisted of the plant superintendent and two assistants. No outside supervision of any kind was given during the tests. The tests were made from Dec. 13, 1960, through Mar. 4, 1961. During this period, 300.03 tons of coal were burned in the No. 3 unit. This tonnage represented 25.5 pct of the total coal requirements for the 1960-61 season. Operation during the period was typical for the comfort heat load which the plant supplies. Of the 78.12 operating days, the boiler was on bank or holdfire 14.31 days, or 18.32 pct of the time. The length of individual bank periods varied from 2 hr to three days. Run periods varied from about 2 hr to 7.26 days. DESCRIPTION OF PLANT AND HEATING EQUIPMENT The new Otterbein College heating plant, completed in the summer of 1957, is located in a 50x50 ft boiler room on the lower level of a combination maintenance building and heating plant. The building is situated away from the main college complex on a hillside, which allows for on-grade delivery of coal to the three bunkers. The bunkers are located directly above and connected with the individual stoker hoppers. Fig. 1 shows an in-plant view of the Coal-Pak installations. The No. 3, hot water, unit is at the extreme right. The heating plant consists of three 200-hp Coal-Paks. Unit No. 1 is operated at 4 psi and carries the steam heating load of 14,000 sq ft EDR (steam) installed in two buildings. Provision has been made to convert these buildings to hot water heating at some future date. Since the unit under maximum load conditions operates only at about 50 pct steaming capacity, a heat exchanger was installed to convert steam to hot water. Thus, during light loads in mild weather the unit can be employed more efficiently to supply both steam and hot water and eliminate the need for operating either of the two hot water units. Units No. 2 and No. 3 serve a hot water heating circuit for a large group of 21 buildings of the College. These boilers deliver hot water at temperatures up to 200°F to the various buildings through distribution lines in tunnels. The present calculated maximum heat loss for the College is 15.195 million Btu per hr. The Coal-Paks have individual design capacities of 6.700 million Btu per hr. Table I lists the design date for the Coal-Paks. The No. 3 unit was chosen as the test unit, primarily because of its bunker location at the far end of the delivery ramp. Because of this location any excess coal above bunker capacity could be conveniently stored and isolated from the adjoining bunkers. Each bunker has a capacity of 30 to 35 tons of coal. The No. 2 and No. 3 hot water generators are equipped with automatic controls which maintain the

Jan 1, 1962

By N. Schapiro, R. J. Gray, G. D. Coe

A petrographic and chemical investigation was conducted to determine the occurrence and distribution of the organic and inorganic forms of sulfur in various size and specific gravity fractions of a high volatile, A-rank, Pittsburgh seam coal. The investigation was conducted to aid in the resolution of the problem of how metallurgical coke of lower sulfur content can be produced from high sulfur coals. The Pittsburgh raw coal contains about 2.4% S in two dominant forms: pyritic and organic. Pyritic sulfur constitutes about 57% of the total sulfur in the raw coal and occurs in macroscopic and microscopic-size particles. A plant cleaning process mechanically separates between 50 and 60% of the pyritic sulfur, mainly the macroscopic particles. The organic sulfur constitutes 41% of the total sulfur in the raw coal and 55% of the sulfur in the washed coal. Thus, organic sulfur is not reduced by physical methods of separation. Organic sulfur occurs in all the coal entities, but in general, increases as the exinoid content of the coal increases. In this study, it was found that carbonizing certain selected low gravity coal fractions containing an average of 0.45% pyritic sulfur and 1.01% organic sulfur produced cokes containing an average of 0.22% pyritic sulfur and 0.91% organic sulfur. However, the organic sulfur in the coke is probably derived in part from the heating of pyrite in the presence of carbon. Thus, the total sulfur in the coal carbonized is the most important factor affecting the sulfur content of the coke produced. Concentration of microscopic pyritic and organic sulfur in the middling-type coal indicates the necessity for rejecting as much of this material as is economically feasible. Most of the sulfur introduced into the blast furnace originates from the coke. Although the sulfur content of the hot metal can be controlled by the addition of flux, the flux used restricts the productivity of the furnace by displacing ore and requires first to be smelted; therefore, low sulfur coke is highly desirable. Since the sulfur content of coke is dependent upon the sulfur content of the coals from which the coke is produced, low sulfur coals are required to produce low sulfur coke. In the western Pennsylvania area, large quantities of good coking coal are available from the Pittsburgh seam, but this coal unfortunately contains relatively large quantities of sulfur. To provide information that might be useful in reducing the sulfur content of this coal in the cleaning process, an investigation was conducted to determine the physical and chemical forms in which this sulfur occurs and with what petrographic components it might be associated. The Pittsburgh seam coal, like most other coals, contains two dominant forms of sulfur: one occurs as the minerals pyrite and/or marcasite and is referred to as pyritic sulfur; the other is combined with the coal substance and is called organic sulfur. Pyritic sulfur is amenable to physical methods of separation, whereas organic sulfur is not. Pyritic sulfur particles must be freed from the surrounding coal if they are to be removed in the washing process. Generally, this requires crushing; the required degree of crushing being a function of the size and distribution of the pyrite. The present investigation was conducted to 1) determine the size, distribution and association of sulfur-bearing minerals in the coal and 2) to determine whether the organic sulfur has a preferential association with specific coal entities. If a preferential association exists, this knowledge may be useful in devising a method for organic sulfur reduction. In addition, a study was made to determine the extent to which pyritic and organic forms of sulfur in the coal contribute to the sulfur in the coke produced from this coal. A representative 3%-ton sample of raw coal was crushed to —3 in. and screened into square-mesh sizes: 3 to 1 in., 1 to % in., % to % in., % in. to 10 mesh, 10 to 35 mesh, and 35 to 200 mesh. Separate samples of the -200-mesh fraction and the all-size composite were also collected. Each size fraction (except the -200 mesh) was fractionated on heavy liquids of the following specific gravities: 1.280, 1.300, 1.325, 1.350, 1.375, 1.400, 1.425, 1.450,

Jan 1, 1963

By E. O. Wagner, V. F. Parry, J. B. Goodman

The low-rank coals containing 10 to 50 pct natural bed moisture represent over half of the tonnage reserve of the available solid fuels of the United States, but only about 2 pct of United States coal production is derived from these fuels. Increased utilization of these large reserves will result if the bed moisture can be removed at the mine in high-speed low-cost processes. This paper presents a theoretical and experimental study of the factors affecting high-speed drying of coal dusts. The time required to heat particles of coal is proportional to the square of their diameter, and it is calculated that the probable time in minutes is equal to 6D2. In other words, a 1/16 in. coal particle should be heated to drying temperature in 1.5 to 2.0 sec. Likewise, 1/8 in. particles should be heated in about 6 sec. The net heat required to dry subbituminous coal and lignite varies from 240 to 375 Btu per pound, depending upon the moisture removed, and this heat can be obtained from 42 to 61 cu ft of hot gases at 600°F. The necessary heat also can be obtained from 7.5 to 11 cu ft of gas at 2000°F. A description of the design and operation of a pilot plant for flash drying coal dusts is presented. This plant dries 1/16 in. by 0 coal dust in suspension in 1.5 to 2 sec with 600°F gas at a rate of 1300 lb per hour per square foot of column area and operates continuously at an efficiency of about 85 pct. The design and operation of another pilot plant for drying 1/8 in. by 0 coal dusts Is also described. This unit dries coal in the fluidized state using the sensible heat of gases introduced at 2000°F and processes coal at a rate of about 1500 Ib per hour per square foot of grate area at 85 to 90 pct efficiency. Over 90 pct of the bed moisture of low-rank coal dusts can be removed by the methods described. The heating value of lignite can be increased 45 pet and that if subbituminous coal 25 pct in a few seconds. The physical and chemical properties of coal dusts before and after drying are presented in the report, and it is shown that the bulk density of the dried coal is equal to that of the raw coal. This phenomenon makes it possible to ship 25 to 45 pct more heat in a railroad car with consequent savings in freight costs. Introduction For several years the Subbituminous Coal and Lignite Section of the Coal Branch of the Bureau of Mines at Golden, Colo., has been concerned with upgrading low-rank coals by removal of natural bed moisture. These fuels contain 10 to 50 pct total moisture, which reduces their industrial value considerably. In 1938, investigations were initiated in cooperation with the University of North Dakota to study drying of lignite by the Fleissner process with heat derived from high-pressure saturated steam. Two pilot plants were built, and two reports were published giving the results of this work.l,2 It was demonstrated that lump lignite and subbituminous coal

Jan 1, 1950

By E. O. Wagner, V. F. Parry, J. B. Goodman

C. P. HEINER*—If you take out 35 pct of the total weight of the coal in the form of moisture, would that be about what it was in the case of North Dakota lignites ? V. F. PARRY (authors' reply)—That is about it. C. P. HEINER—That will be about a 35 pct loss and the final product will be about 11,000 Btu? V. F. PARRY—That is right. The heating value of the dried lignite is 10,000 to 11,000 Btu. C. P. HEINER—And the thought is not, then, to produce a commercial coal with that heavy loss, but to make other products—that is, synthetic fuel base, is that it? V. F. PARRY—The principal thought is to upgrade the coal, making it a more favorable raw material for industrial purposes, both for shipment and direct use. You see, the trouble in these lignites is that their moisture penalizes their

Jan 1, 1950

By Claude P. Heiner

mountain region to M tht Coast points for domestic consumption and for export are shown in Table 11. There is considerable disparity in rates from both Rock Springs, Wyo., and Castle Gate, Utah, to the four coast cities where the slack coal is to be used for purposes other than export. The rate on coal to be exported is the same from either starting point to any of the four coast cities even though there is a difference of as much as 341 miles in the shipping distance. It is interesting to note that the freight rate between Sunnyside, Utah, and Fontana, Calif., on coking coal is $5.05 per ton and that coal up to 8 in. can be moved on this rate if it is suitable for coking. This rate was published late in 1942 on a contemplated annual movement of more than 500,000 tons. There have been decreases in freight rates since 1923 on movements of slack coal from Utah into Seattle and Portland due to pressure on the railroads and to greater. quantity of coal shipped. It is the author,', opinion that a movement of slack coal in excess of 3 million tons of coal per year from Utah to any point in central California would justify a freight rate equal to that puhlished for Fontana, Calif.. or $5.05 per ton. The movement of 3 1/2 million tons of coal per year on the basis of 240 mine working days per year would require that 14,600 tons be handled each mine working day. If it is assumed that shipments could be arranged for a 6-day week, the average railway movement would he 11,200 tons, or approximately 3 trains containing fifty-five 70-ton coal cars per day. Such movements of coal would require railroad equipment represented by the investment amounts stated in Table 12 and entail the services of 250 men. Table 12 ... Railroad Equipment and Investment Required To Move 11,200 Tons of Coal a Day from Utah to California Railroad Equipment Cost 2800. 70-ton coal cara at $6.000 each $16,800.000 32 locomotives at $310.000 each. 9.920.000 Miscellaneous eauiument:.......... .5;000:000 Total........................ $31,720,000 It therefore appears that, under presently known mining methods, the lowest price at which coal could be sold f.0.b. the mine in amounts of 3 1/2 million tons per year for generation of power in central California would be $4.60. It also appears that the lowest freight rate that could be expecled between intermountain points and the central California area would be $5.05 per ton, making a total cost of coal delivered at a plant site of $9.65 per ton. Conelusions The following are the author's conclusions: 1. Coal mines in Utah and in the Kemmerer and Rock Springs districts of Wyoming could increase annual production by 6 1/2 million tons per year. 2. Under present conditions coal could probably be delivered to any steam electric plant in central California at a price not to exceed $9.65 per ton. 3. The use of coal at such a price, while higher than the equivalent present price of fuel oil, is entirely feasible. 4. There are adequate railroad facilities for movements of large quantities of coal from the intermountain region to the Rest Coast. 5. In a national emergency it probably would be extremely difficult, if not impossible, to obtain sufficient oil to meet requirements of the greatly expanded West Coast steam electric generatsing capacity. 6. The intermountain region contains ample coal reserves to supply all conceivable demands for West Coast power generation for a number of generations. 7. Increasing demands of labor threaten to lessen, if not eliminate, savings in cost of coal production through the use of new mining machinery. 8. Continuation of experiments in socialism by the Federal Government through construction of hydroelectric generating plants, particularly those unrelated to land-use reclamation, defies justification. Rates under this concept of a governmental function are subsidized through greater taxation of its people. Private capital is available to construct steam plants, or hydro plants where feasible, and should be permitted to continue in order to preserve the principles of our free enterprise system. DISCUSSION (L. C. McCabe and Robert P. Koenig, presiding) C. C;. BALl*—I was asked to lead off the discussion, but it is not with the thought that I might be able to add anything to the paper. The thoroughness with which it was prepared rather forestalls the asking of many questions. Your treatment, Mr. Heiner, is a very valuable contribution. I do want to suggest—that although you have limited your study to this specific question, with certain geographic limitations, many of the things in your paper apply just as well to the eastern coals. I want to agree 100 pct with your final conclusion concerning government-subsidized construction. Id. C. McCabe*—It is certainly worthwhile to take stock occasionally to see where we are going in problems of this nature. I agree with Mr. Heiner that ultimately the only reliable source of fuel that the West Coast has is coal hut the time factor is the difficult element to evaluate. Just before I came here I discussed this subject with N. B. Hinson, Vice President and Executixe Engineer of the Southern California Edison Company, and Chairman of the West Coast Inter-Power Exchange Committee. He has given much thought to utilities' fuel supply and it was very helpful to me in preparing a discussion of the paper to talk with him beforehand. Stock taking and forecasting of future development are essential to the continuing success of any enterprise. Mr. Heiner has called attention to the unprecedented growth of central and southern California and to the increased demands for fuel and power which have accompanied it. He discusses the increased fuel oil and natural gas requirements and the probable limits on the future use of these fuels and of hydroelectric power. In contrast to the calculable limits of these sources of electric energy, the author points to the availability of enormous reserves of coal in the Rocky Mountain States adjacent to the Pacific Coast which can be utilized for power generation. That there will be increased use of coal for power generation in the area under discussion is generally accepted hut it is in the timetable of such development that there is not complete agreement. In a recent report, Mr. Hinson reviewed the future power outlook for the Pacific southwest area. He pointed out that the use of steam plants in connection with water power plants in this region has made the maximum use of hydroelectric energy possible, and that the correct balance between hydro and steam generating plants produces the most economical overall system. Steam plants in the area which had been installed to protect against deficiency in hydro energy in dry years were used to carry war loads. Fortunately, no dry

Jan 1, 1950

By F. G. Miller

Earlier studies of the mechanism of flotation showed that coal flotation products are contaminated by composite coal and mineral particles. The mineral matter of these particles has the dual effect of increasing the specific gravity and decreasing the coal surface of the particle available for bubble attachment. The present study showed that these particles are more loosely held in the froth column than the high grade coal particles, especially in the coarser sizes. Consequently, it is possible in the laboratory to produce a secondary concentration of the product by sprinkling the froth product with water to wash these loosely held particles from the froth during formation and recovery. To improve coal flotation, Bethlehem Steel Corp.'s research department has been working on a number of related problems based on both physical and chemical factors. The ideal is of course full understanding of the interrelated effects of both sets of factors. However, detailed studies1 of each physical factor have produced immediately usable results in commercial coal flotation and are providing the basis for our current work on the effect of chemical factors. Since these detailed studies provided the basis for the present investigation of froth sprinkling, their key results are highlighted here. For example, for a highly floatable bituminous coal, particle floatability was shown to be directly related to the percentage of coal surface available for bubble attachment and inversely related to particle mass. The data also underscored that in a given size range the addition of mineral matter to a particle makes flotation more difficult both by adding to the mass of the particle and by decreasing the amount of coal surface available for bubble attachment. Size also affects particle floatability in that as the size of particles of a given specific gravity increases, mass increases and the ratio between coal surface area and mass of the particle decreases. Flotation tests showed that any recovery of the coarsest particles in a coal feed is accompanied by progressively higher recovery of finer and finer particles. Consequently, fine high-specific-gravity particles are recovered with the coarse good coal. As a result, when the entire 14 mesh x 0 size range is processed by froth flotation, the good coarse coal is contaminated with high-specific-gravity fines. It is the small quantities of these fines that must be rejected from the froth product if flotation efficiency is to be increased above its present level. These principles and findings, together with work by Professor V. I. Klassen,' led to the froth sprinkling investigation reported in this paper. Working with Russian coals, Klassen had shown that froth sprinkling washes loosely held refuse particles from the froth and compensates for the water lost in the upper froth layers and increases its stability. As a result, the coal particles are retained in the froth and the loss of coarse coal from the froth is prevented. Decreases in ash of 0.1% to 1.5% were reported by Klassen. Working with a 28 mesh x 0 American coal, the author of the present paper found that single-stage flotation coupled with froth sprinkling produced a product comparable to that obtained by the more expensive method of roughing and cleaning.3 The investigation reported in the present paper expanded study of the effect of froth sprinkling to include each of the standard size fractions of a bituminous coal. The main findings are as follows: (1) For those size fractions between 48 mesh and 150 mesh, froth sprinkling produces a marked reduction in both sulfur and ash. In the case of those sizes coarser than 48 mesh, while this reduction is not as significant, the additional benefit of shorter retention time is still a plus for froth sprinkling. Furthermore, when froth sprinkling is coupled with normal fast flotation, the product purity approaches that obtained by starvation reagent feeding, i.e., gradual feeding of flotation reagent to float the recoverable coal from the pulp slowly in several increments. The specific results for these two size groups are: (a) 14 x 48 Mesh. By using froth sprinkling with fast flotation, product sulfur can be reduced to a level

Jan 1, 1970

By Shiou-Chuan Sun

THE effects of oxidation on the flotation behavior of sulphide minerals have been extensively studied 1-3 but no similar study has been made of coals. Coals of bituminous and lower rank undergo atmospheric oxidation during mining and storage, and their degree of oxidizing increases with temperature, 4,5 and time of exposure." The problem of recovering fine oxidized coal from culm piles, rivers, and streams by froth flotation has become increasingly important to the coal industry as well as to those concerned with air and stream pollution. This paper describes the flotation behavior of oxidized and unoxidized coals and carbons in the presence of oily collectors and presents the reagents found effective in the flotation of oxidized coals and carbons. Except where otherwise stated, flotation tests were performed in a 50-g Denver flotation cell. Solid feed for each test was 30 g, and the pulp dilution was kept at 8.5. The —65 mesh coal sample was wetted by agitation with water in the flotation cell for 6 min, then conditioned with a predetermined amount of collector for 2 min, and finally floated with pine oil as frother for 3 min. The oxidation of coals and carbons was performed in a vertical, electrically heated glass tube, shown in Fig. 1. One hundred grams of —65 mesh coal were fed into the glass tube and heated to 10° to 20 °C below the predetermined temperature of oxidation. Compressed air was admitted to the tube at a rate of 0.05 cu ft per min and the temperature was controlled by a variable voltage regulator. The oxi-

Jan 1, 1955

By J. Visman

A simplified method of assessing the characteristics of a cleaning unit, including washability curves, yield figures, ash error, separating gravities, and error curve. FOR more than 25 years evaluations of coal cleaning units have appeared in many publications, and during this time considerable progress has been made in developing the theory and techniques of calculating washery results. A variety of characteristics have been defined over the years, many receiving general recognition during the first post-war Coal Preparation Conference in Paris in 1950. Coal preparation has become a science, and the approach to preparation problems is being revolutionized. Formerly, for example, if a coal operator wanted to know the performance of a given cleaning unit for a particular grade of his run-of-mine, he either shipped a carload to the manufacturer for a test run or relied on a report of a test carried out on a coal similar to the one he intended to clean. In modern practice the expensive, time-consuming test work generally can be avoided if the washability curves of the coal in question and the error curve of the cleaner are known. Normally a guarantee can be given on the strength of this information. General acceptance of modern standards has thus reduced the need for pilot-scale models of existing types of coal cleaners. Needless to say, the method requires exhaustive and accurate information on the cleaning unit and on all the additional circumstances affecting its results, information that ultimately can be secured only from actual tests made in the laboratory or in the washery. It is not the purpose of the present discussion to compare the merits of various characteristics, but to describe the general method of calculation, including a method of obtaining data with a minimum of laboratory work. All data presented here were derived from tests made at the plant with portable field equipment, using small quantities of varsol, carbon tetrachloride, and bromoform. It will be explained later that the use of standard fractional ash contents designated normalized ash contents aids considerably in reducing the routine testing of coal cleaners. Like any other statistical procedure, this method has limitations, and it is not recommended for any work in connection with guarantees. Even a varying commodity such as coal, however, will follow the law of large numbers, which is the basic law of statistics, thus allowing simplification of test work without appreciable loss of accuracy. The characteristics needed for evaluating cleaner performance are normally derived from a float-sink analysis of samples of the clean coal and the refuse, followed by ash determinations of the various fractions. Usually a sample of feed is also collected to find its ash content and to make a single specific gravity cut, both in connection with determination

Jan 1, 1955

[Abstmct of remarks by R. II. Sweetser arid suhscqueut discussion at the New York Meeting, February, 1926. The Transactions mill ultimately contain a report of work resulting from these discussions. Need for a standard of ualuration.—There should be an accepted method for evaluating the different kinds of bituminous coals based on their carbon just as that for iron ores is based on iron. Variation in the classes of coals and their desirability fol the different industrial uses is analagous to the case of iron ores. The iron people have developed a standard. In the past coals have not been intelligently distributed because the public has not been informed as to its uses. Many operators have known nothing about the final disposal of the coal shipped from their mines. Sales agents and retailers have had no means of evaluating coals except to make the price as high as the market will stand. Producers and distributors need to know how much more valuable the coals would be if prepared so as to contain less objectionable material. Mr. Swectser cnlletl on the Goal and Coke Committee of the Institnte to organize a study through producers and users to develop a method scientifically and comnereially sound E. A holbrook said that the information exists but the public is unwilling to investigate. He praised Ashley's1 nomenclature of the different kind of coal which has been accepted by the Coal Mining Institute of America and recommended to the American Enginecring Standards Commitee. G. S. Rice pointed out the wider variety and distribution of consumption of coal compared to Iron ore. C'. M. Young approved Mr. Sweetser's remarks and hoped lor a research institution, probably endowed, to study utilization of coal after it comes from the ground. Mr. Sweetser cited incidents to prove his former statements. He said that a reduction of 1 per cent. ash in the coal would cut down the cost of pig iron at a blast furnace 30 c. a ton, that the coal men should tell what the iron men would have to pay to get better coal. H. J. Prryn endorsed the need of blast-furnace operators to know the kind of coal from which their- coke is made and the latler's ash content, as this affects coke consumption. A. C. Fieldncr explained that the difficulty of evaluating coal on the basis of chermical analyses for calorimetric tests is: (1) representativr

Jan 1, 1927

By F. J. Chernosky

Most previous studies of coal flotation utilized chemically pure reagents. Since such reagents are not available in quantity, a study of various wmmercially available reagents as frothers was undertaken. Flotation procedures similar to those used in a large number of commercial coal flotation plants were employed. The reagents used were compared on yield-selectivity-wst basis. The selectivity was found to be relatively constant with yields above 70% but the reagent cost varied greatly. The types of reagents available were compared. In the past, a number of papers have been written on the use of various reagents as coal flotation frothers. For the most part, these have been an attempt to correlate the intrinsic chemical and physical proper- ties of the reagents or reagent groups to the floata-bility of various fine coals. Because of the type or nature of evaluations made, chemically pure reagents were normally used. Generally, these reagents are unavailable in commercial quantities. Therefore, the results obtained with these reagents were usually limited in usefulness to the plant operator or metallurgist. This paper presents the results of a study in which commercially available forms of various reagents were used as flotation frothers. Flotation procedures which would conform in general to those employed in a large number of commercial coal flotation plants were utilized. The objective of the test was to compare these reagents on yield-selectivity-cost basis, that is, 1) the yields obtained, 2) the ash levels obtained and 3) the reagent cost relating to these results. REAGENTS The reagents employed have been grouped into the following chemical classes: 1) aliphatic alcohols, 2) terpines, 3) glycols (synthetic water-soluble

Jan 1, 1963