Search Documents

By Frank Ruskey

This report describes a computer program devised by the Bureau of Mines to model coal-mining situations where one or more panels encounter oil or gas wells. The program seeks in several hundred trials to evade the wells if possible or to minimize their influence by shifting or skewing the mine plan and/or adjusting the centerline dimensions of the entryways. Upon completion of computations, the program sorts the hundreds of models which have been tested, and lists the 10 best with their associated parameters. It also draws a mine plan of the best configuration, showing the entryways and crosscuts along with the "lost" coal remaining in the barrier pillars surrounding the various wells.

Jan 1, 1972

By Frank Ruskey

Many problem associated with potential hazards in a proposed mining area may not be adequately appraised because of the complexity of trying to evaluate them in terms of production requirements. Frequently, encountered hazards have to be dealt with by day-to-day operational schemes that require the miner to either force a way through them or avoid them by blocking off the area in which the hazards are known to exist. These considerations, after the mine is in full production, can be costly to the mine operator and can increase the danger to the miners. A hazard-evasion computer program for mine planning that will appraise proposed mine layouts on the basis of existing or potential hazards has therefore been developed. The program is intended for use during the planning phase of a mine, where it should assist the mining engineer in making decisions in mine design. With the output from this program, the mining engineer should be able either to corroborate his judgments made on the basis of mining experience or to find unanticipated solutions to design problem. The program tests hundreds of possible solutions to a mining layout, and by sorting out the 10 best (based on a criteria of minimum-abandoned-coal) limits the number of choices that need to be considered and appraised for applicability to a given mine scheme.

Jan 1, 1973

By R. Hemp

This paper describes work carried out to obtain a heat balance in the B3 shaft longwall stope at Blyvooruitzicht gold mine. Recordings were made of the temperature of the air and chilled water entering and leaving the section during three periods, August 1 September 1977, November 1 December 1977 and March 1978. These recordings, together with numerous other measurements were used to determine the rate at which heat was being removed from the section by the various fluids flowing through the section. The rate at which heat was entering the section was then calculated, by considering each source in turn. These two sets of figures made it possible to draw up a heat balance, and also obviously gave vital information on the magnitudes of the various heat sources and on the methods used to remove heat. In general reasonable heat balances were obtained, the errors being in the range -6 per cent to +22 per cent.

Jan 1, 1980

By C. K. Kocsis

A study was undertaken to evaluate the thermal environment and determine the contributing heat sources within the existing 153 Orebody of Coleman/McCreedy East Mine which would then enable the prediction of the climatic conditions in the mine?s future 170 Orebody. The study entailed continuously monitoring, for a 2-week period, the dry-bulb temperature, humidity and barometric pressure along the existing intake airways from surface down to the 4810 Level and throughout an active mining area on that level. Furthermore, the mining activities and associated equipment that could be responsible for any changes in the temperature and humidity conditions within this mining area were also monitored. These data were then used to develop and validate a climatic simulation of the mine?s mechanized cut and fill mining method. This climatic model was then transposed to the future 5700 Level in the deeper 170 Orebody, to determine the environmental conditions within its production workings and along the main haulage route ascending from that area. Based upon the simulations performed it was shown that the level of ventilation planned for the new orebody should be able to maintain adequate environmental conditions. However, this study did emphasize the importance of the appropriate distribution of airflow in workplaces that used auxiliary ventilation in order to sustain a suitable thermal environment.

Jan 1, 2009

By H. Kotzé

Titania slag is used as feedstock in the production of titanium dioxide pigment. It (titania slag) is the product of ilmenite smelting,a process whereby ilmenite is reduced at high temperature utilizing anthracite as a reducing agent. Although various slag tapping configurations are employed throughout the ilmenite smelting industry, the method of tapping the slag from the furnace into bell shaped cast steel pots, was the subject of investigation in this study. The paper describes the formulation of a cooling model used to calculate and subsequently predict the temperature profile of a slagblock during its cooling within the various cooling environments of pot cooling, air cooling and water cooling. The model was calibrated against actual internal slag temperature measurements and verified with information obtained from both pilot and industrial scale blocks. The paper concludes with solidification results and their practical implication.

Jan 1, 2010

By A. M. S. Hussein, B. E. Rogers

Progressively more stringent emission limits and advances in regulations and enforcement have made air compliance more difficult for metallurgical facilities. This has historically required improved collection and treatment of stack sources. Fugitive emission reductions are now increasingly required to achieve compliance. Typically small in magnitude, fugitive emissions have a disproportionate impact on ground level concentrations, can be visible to the public and can influence workplace health and safety. Moreover, these emissions are complex, as they are spread over multiple sources, distance and time and are affected by various activities and conditions. As such it is difficult to find, define and monitor these emissions and their impacts. This difficulty translates to the design of emission reduction measures and operational requirements. This paper presents an overview or ‘heuristic’ of fugitive emissions management for compliance in existing operations. This includes aspects such as the impact of regulations on project scope, approaches to developing a comprehensive emission inventory, considerations for solution development and the plant’s role in sustaining compliance once achieved. Case studies are presented to demonstrate how portions of this approach have been applied.

Jan 1, 2015

By Diogo Peixoto Cordova, Italo Gomes Gonçalves, Andre Cezar Zingano

The top-down extraction sequence in the sublevel open stope method relies on rib pillars to support excavations, making pillar and stope stability crucial for controlling dilution. This study introduces an integrated methodology using a genetic algorithm to optimize the layout of open stopes and rib pillars while considering both economic and geomechanical performance. The methodology incorporates user-defined parameters such as the minimum size of stopes and pillars, maximum accepted dilution and acceptable percentage of pillar failure. A profit function that attributes economic value to the geometric configurations, including geomechanical performance, is employed. The geomechanical performance, assessed using numerical models in FLAC3D, includes the average percentage of pillar failure and potential dilution. The study was tested on a mining panel from an underground gold mine using a top-down mining sequence. The optimization achieved an 8 percent increase in net profit compared to the traditional engineer’s design when 70 percent hangingwall support efficiency was assumed, and a threefold reduction in pillar failure percentage. When no hangingwall support was considered, the net profit increase reached 22 percent. These results demonstrate that the proposed methodology enables integrated optimization, balancing mining costs with geomechanical performance and reducing the need for secondary support compared to traditional methods

Nov 1, 2024

By X. Bai

A new heuristic sublevel mining stope optimizer is presented. The optimizer seeks the best locations and lengths of a series of vertical raises that, together with the blocks linked to each raise, define a mining stope. Five design constraints ? the footwall angle, the hangingwall angle, the number of raises, the maximum distance of a block from a raise, and the minimum width required to move the farthest block towards the raise ? allow the shape of the sub-stopes associated with each raise to be controlled. The optimization is done on the locations and lengths of raises using a genetic algorithm to efficiently sample the parameters? space. For each raise, a local network is defined in cylindrical coordinates around the raise such as to impose the design constraints. A maxflow algorithm on the local network is used to determine the optimal sub-stope for each raise. All substopes are combined to define the global stope for the entire deposit. The best global stope is obtained using a genetic algorithm to find the raise parameters providing the best profit over the entire deposit. Two synthetic cases and one real deposit are used to evaluate the new algorithm and compare the results with the single-raise optimizer. The multiple raises approach leads to significantly improved economics compared with the single-raise stope optimizer, and the dilution is also substantially reduced compared to the single-raise case.

Jan 1, 2014

By E. L. Gillenwater

Coal mine planning has three distinct decision levels: (1) decisions made at the upper level of management that determine production requirements for specific mines, (2) decisions made at the middle management level, the mine level, that determine how the mine satisfies its production requirements, and (3) decisions made at the operating level of management, the sectional level, that determine the sequencing of machine movements at the face. In this paper, the underground production scheduling problem is formulated in multi-stages using the Hierarchical Production Planning (HPP) approach. Two linear programming HPP models for accomplishing decisions at the first two levels are developed. Both models address the aggregate production planning process. The Mine Production Scheduling (MPS) model permits determination of monthly production and inventory levels. The Section Production Scheduling (SPS) model incorporates a quality blending requirement into the determination of weekly sectional production and inventory levels.

Jan 1, 1995

By John A. Herbst, Ming Song, Xiangjun Qiu

"It has been known for sometime that as wear occurs in tumbling mills there is an associated change in mill throughput. These changes have traditionally been simplistically, attributed to “mill volume effects”. New high fidelity simulation (HFS) tools (involving DEM, CFD and Breakage models) are now giving new “microscale” insights into the complex interactions that occur between evolving lifter/liner profiles and breakage. An illustration of this analysis is shown in Figure 1 below.Here we see that after a new lining is installed (Region I) the wearing process reduces the liner thickness resulting in a larger power draw and an associated higher throughput until Region II is reached. By this point the lifter height is reduced significantly changing charge motion (less cataracting) the power begins to decline, but the comminution efficiency increases with this type of “calmer” breakage environment therefore the throughput continues to increase. In Region III the lifter is no longer providing the minimum required charge lifting action, the power and the throughput both drop off significantly. In the last two stages the behavior is especially complex because throughput is not linearly related to power since grinding efficiency is changing.The study described here shows that these new HFS tools allow the design of wear part profiles which will maximize mill productivity over the entire life of liner/lifter systems. A simple example of such a design procedure is shown involving the selection of a sinusoidal profile for a 34 ft diameter SAG mill.The paper discusses how the principles exposed in this simple example can be applied to search for an optimal profile in which non-standard modifications are allowed to compensate for throughput or wear shortcomings of standard profiles."

Jan 1, 2003

By John A. Herbst, Ming Song, Xiangjun Qiu

It has been known for sometime that as wear occurs in tumbling mills there is an associated change in mill throughput. These changes have traditionally been simplistically, attributed to “mill volume effects”. New high fidelity simulation tools (involving DEM, CFD and Breakage models) are now giving new “microscale” insights into the complex interactions that occur between evolving lifter/liner profiles and breakage. The study described here shows that these new tools can allow the design of wear part profiles which will maximize mill productivity over the entire life of a liner/lifter system.

Jan 1, 2003

By Dennis Travagini Cremonese

In the early stage of front end studies of an Iron Ore Project, the sizing of surge capacities and stockpiles are normally assumed based on the experience of the study team. Understanding and sizing of these capacities at the early stages of the project are important for future stages of the project as drastic changes in sizes will impact the economics of the project at that stage. An innovative user configurable high level dynamic modeling tool has been developed to assist in speedy evaluation of assumptions made by the study team. This model incorporates systems or facilities that are commonly used iron ore project from mine to port. This model includes subsystems that will simulate all the logistical components, major process plant systems required for an Iron ore project. The output data provided by this high level dynamic simulation tool will enhance the confidence level of engineering carried out during the early stage of the project. This paper discusses the innovative tool capabilities and a test case comparing various techniques used in iron ore project front end studies.

Aug 1, 2018

By Hua Hou, Xiaofeng Niu, Wei Liang

"The explicit finite difference (EFD) method is used for calculating the casting temperature field during solidification. Because the time step is limited, the computational efficiency of the EFD method is lower. In order to improve the computational efficiency, a fourth-order in space and second-order in time model based on the equivalent specific heat method and the alternating direction implicit (ADI) method is established. The degree of similarity between the simulation results and the experimental results is analyzed. The results show that the simulation results of this high order mathematical model are close to the experimental results.IntroductionThe 3D heat transfer equation of temperature field during solidification process is as the following: [1-3]."

Jan 1, 2013

By E. Yan, M. Mankosa, E. B. Wasmund

Mechanical cells are the dominant unit operation in base metal rougher flotation applications worldwide. As economic demand for metals increase, and as the feasible ore grades decrease, the installed capacity of mechanical flotation units worldwide has greatly increased, adding significant capital and operating cost. One opportunity to improve this situation is to use fundamental knowledge to make the industrial flotation process more efficient. A key insight is that the flotation process can be optimized by dividing the processing of the pulp into two distinct fluidic environments; a collection cell where air and pulp mix in a highly energetic compartment, and a low energy gravity separation cell. This is the basis of the “2-stage flotation device” that has been patented by Eriez and marketed under the tradename StackCell™. Two industrial case studies will be presented to highlight the potential metallurgical and commercial advantages of the StackCell. In the first, a train consisting of three pilot scale StackCells (each 0.6 metre diameter) was run in parallel with a train of conventional mechanical cells in a major copper concentrator and benchmarked against a batch Denver test. In the second, the performance of a 3 metre diameter StackCell in a nickel sulfide cleaning application was benchmarked against a batch Denver test. The flotation kinetics observed in the StackCells were 2.4 to 2.9 times faster when compared with the lab Denver test. In the first case study, the kinetics of the StackCell was about six times faster than conventional mechanical cells. It is hypothesized that the efficiency improvement in kinetics is because of reduced “drop-back” during the froth recovery phase, which is reduced because of the reduction in the shear that is present in a conventional mechanical tank cell. This result suggests that a 2-stage flotation system can be used to reduce the working volume of flotation units by five to six times. This would allow operators to significantly reduce the size of their flotation lines for a comparable flotation objective. Some discussion will follow about the scale-up criteria, maintenance and operability issues, comparisons of layout, and possible cost savings. INTRODUCTION The solution that most equipment suppliers have offered to reduce the cost of mechanical flotation equipment over the last 30 years has been to increase the size of the flotation unit cell (Mankosa, 2017). For example, three 100 m3 machines with three smaller motors, mechanisms and control valves could be replaced with a geometrically similar 300 m3 with a larger version of each ancillary component. While there are some efficiencies and cost improvements to be gained by this approach, it does not take advantage of fundamental insights into the flotation process, and it does not represent a step-change in terms of process design or economic benefit for the customer. The advantage of the “bigger is better” approach is that there is past experience of incremental improvements by making cells larger and there is a well-established scale-up method, which allows practitioners to estimate equipment capital costs based on very simple laboratory test- work. A different paradigm, which is gaining interest rapidly is to use a unit operation in which it is easier to optimize the flotation process, which will be described in this paper. This approach is often referred to “2- stage flotation”. Because this approach is new, it is important to benchmark it against existing conventional technology and to demonstrate a robust methodology for sizing equipment and flowsheets. This paper aims to address these issues with two case studies.

Jan 1, 2019

Although developed primarily for sintering tantalum, the unit to be described can be used to heat-treat metals in the form ofa bar, wire or strip, by passing a current through them. The upper temperature limit with this type of heating is the melting point of the metal being heated.The unit was designed for vacuum work, but. various gases can be used if required.Briefly, the vacuum sintering furnace consists of a bell which is counter-balanced and may be lowered onto the brass base plate which holds the electrodes. A rubber ring seal is used for vacuum work. The lower flexible grips are bolted to the brass base plate which is at earth 'potential, while the other electrode passes through the plate by way of an electrically insulated vacuum seal. This upper electrode, the height of which can be altered as desired, the lower grips, and the bell are water cooled. The vacuum line to the pumps and a line to the vacuum gauges also lead from the base plate. The more important sections of the unit are described below.THE BELLThe unit was designed so that the bell could be lifted clear of the base plate and the electrodes, thus facilitating adjustment of the latter and the mounting of the specimen to be heated. A double walled steel bell, 20 in. high, with t in. cavity was used. The bell was fabricated from 10 gauge mild steel sheet using a double overlapping run of arc welding for all seams. A water inlet and outlet...

Jan 1, 1946

By Qinghua Gu, BUQING XUE, XUEXIAN LI, JIANGSHAN SONG, Qian Wang

Updating the openpit vehicle transportation network has the problem of being time consuming and low precision. To address this problem, a high-precision road network model construction method for unmanned vehicles in openpit mines is proposed. This method can be divided into two steps. In the first step, an improved deep learning image processing model named DeepLabv3+C (DeepLabv3+Concat) is presented, and the road information extracted by the DeepLabv3+C network is used to construct a three-dimensional model of the openpit mine road network. In the second step, aiming at the time-consuming problem of unmanned vehicles meeting in openpit mines, a vehicle meeting strategy is proposed. This strategy is used to guide the navigation of unmanned vehicles in openpit mines. At the end of the study, vehicle running simulation was carried out on the road network model using Unity, a 3D visualization simulation software. The high-precision unmanned road network model of openpit mines studied in this work can further promote the construction and development of smart mines by acting as a high-precision map for unmanned vehicles.

By A Turns

In a survey conducted by symplexi with underground miners in Australia; 78 per cent of participants believed that ‘safety’ is all about people. If ‘safety’ is about people, then is the mining industry focusing on the wrong thing? It would be fair to say that the mining industry is heavily systems focused. Companies develop a safety management system and use this to show regulators that they comply with legislation – however, that is only half of the picture.

May 5, 2022

By Qinghua Gu, BUQING XUE, XUEXIAN LI, JIANGSHAN SONG, Qian Wang

To solve the problem of time-consuming and low precision in updating the open-pit vehicle transportation network, a high precision road network model construction method for unmanned vehicles in open-pit mines is proposed. This method can be divided into two steps. In the first step, an improved deep learning image processing model named DeepLabv3 + C (DeepLabv3 + Concat) is presented. Then, the road information extracted by the DeepLabv3 + C network is used to construct a three-dimensional model of the open-pit mine road network. In the second step, aiming at the time-consuming problem of unmanned vehicle meeting in open-pit mines, a vehicle meeting strategy was proposed. This strategy is used to guide the navigation of unmanned vehicles in open-pit mines. Besides, the DeepLabv3 + C network is verified by comparing the mIOU (means Intersection Over Union), accuracy, and continuity of road image extraction with the mainstream networks. The road network model constructed in the first step is quantitatively analyzed, and its performance is compared with GPS trajectory clustering methods. At the end of the paper, vehicle running simulation is carried out on the road network model by using Unity (a 3D visualization simulation software). The results show that the road network model constructed by this method can meet the navigation requirements of unmanned vehicles in open-pit mines, and the feasibility of the vehicle meeting strategy is proved.

Jan 11, 2022

By Richard F. Sliwoski

The Virginia State Capitol was designed by Thomas Jefferson and constructed in 1785. The Capitol is of great historic and architectural significance to not only the Commonwealth of Virginia but to the nation. It is the oldest operating Capitol in the U.S. and required a total restoration/renovation as well as an expansion to continue to remain functional. Site conditions dictated that the expansion (a new visitor center) be placed underground on the south side of the Capitol building, requiring a 40-foot deep excavation approximately 5 feet from the Building. Because of its historic significance, every measure had to be taken to ensure the safety and function of the Capitol during construction. The construction techniques that were used to make the deep excavation and protect the historic Capitol included a tied back concrete slurry wall, jet grouting, compensation grouting, and instrumentation monitoring. This paper describes the history of the Capitol building, the techniques that were employed for construction of the deep excavation, results of the latest movement monitoring, and factors contributing to meeting the restrictive movement goals.

Jan 1, 2006

By J. R. Kiji

The Cerro Matoso S.A. mine and smelter, in the Cordoba lowlands of northwestern Colombia, consist of a dedicated laterite nickel mine, ore blending, drying and an RKEF process to produce high-quality ferronickel. At a project investment of $400M, first production of ferronickel was in September 1982, and in its inaugural year CMSA produced 6,150 tons of contained Ni from a mined ore grade of 3.2% Ni. Initial operational difficulties resulted in a number of furnace run-outs, which impacted ramp up to design ore throughput of 128 dry t/h Since then CMSA has steadily incorporated process improvements and initiatives to take the single line operation to an ore throughput of 175 dry t/h. A second 175 dry t/h line was added in 2001 (investment of US$ 300M) to consolidate CMSA as one of the world's lowest cost Ni producers with an installed annual production capacity of 50-55,000 tons Ni. The most recent addition is commissioning of Phase I of an ore-upgrading project to counteract the effect of declining ore grades. Keywords: Laterite, ferronickel, pyrometallurgy, smelter.

Jan 1, 2004