Search Documents

"Rock falls involving a relatively small amount of material are a leading cause ofinjuries in underground mines in the United States. A contributing factor is unwantedblast damage and over-break. A goal of the United States National Institute forOccupational Safety and Health is to reduce the number of ground fall-related accidents by improving drift driving practices through the introduction of perimeter control blast designs. This paper presents a blast design technique based on a hydrodynamic method. Using commonly available explosive and geometry data, the theoretical particle velocity is calculated as a function of distance away from a cylindrical charge. A calibration factor is introduced to account for actual conditions by comparing the predicted values to a set of field data. The calibrated curve can then be applied for design. The paper introduces modifications to account for different explosives from those used in a calibration test. The application of the approach is demonstrated with respect to a data set from a large-scale concrete block test."

Jan 1, 2009

Develop a safe, nonpolluting power source for underground mining equipment. Approach The Bureau of Mines and EIM-CO Mining Machinery International entered into a cost-shared project to develop and demonstrate a novel power source for mining. An underground mining utility truck was equipped with an ultra-low-emission hydrogen-fueled engine and a safe, metal hydride fuel storage system. How It Works The nonpolluting hydrogen engine and a "solid-state" (metal hyride) hydrogen fuel storage system were combined to power a utility mining vehicle. An 85 horsepower diesel engine was convened to burn hydrogen. The engine was converted by equipping it with a spark ignition, lowering the compression ratio, turbocharging, and adding an ahercooler and a parallel fuel induction system. Parallel induction provides two intake paths, one for hydrogen and one for air. It avoids intake-manifold backfiring by keeping the hydrogen and air separate until they enter the cylinder.

Jan 1, 1986

By G. J. Hasenfus

This paper presents the results of an extensive hydrological and geomechanical monitoring program which Gas conducted at a longwall coal mine in W. Va. The field program included monitoring of groundwater levels. overburden hydraulic conductivity, overburden movement, and surface subsidence relative to the passage of the longwall. Overburden geology and rock strength characteristics were evaluated prior to mining. A postmining corehole was drilled to evaluate main roof fracturing. An overburden response model is proposed based on the correlations between hydrological and geomechanical data.

Jan 1, 1988

By W. A. Ahrens, J. H. McNamara, J. G. Franek

"An economical, pollution-free process has been developed for the hydrometallurgical extraction of copper from sulphide ores. The extracted copper, in the form of cuprous chloride (CuC/), is converted by reduction to copper metal. The metal is melted and fire -refined into wire bars which meet the standards of electrolytic tough pitch (ETP) copper wirebars. IntroductionThe successful development of the Cyprus Copper Process has been an evolutionary series of events covering a time span of some nine years. The original process, based on an electrolytic membrane cell principle , was abandoned in 1975 because of technical, economic and pollution problems. During the past four years, the pilot plant has been reconstructed based on a new flowsheet and operated successfully in several campaigns, some for as long as four months. The pilot-plant hydro section operates at a 225-lblhr copper rate. In October 1977, a feasibility study was completed by Jacobs Engineering, Pasadena, California. The study showed favourable economic and technical feasibility. Jacob's studies in 1978-79 revealed favourable comparative economics with other known pyrohydro processes and favourable economies of scale.The Cyprus Copper Process converts copper concentrates of varying composition into copper metal, which has been proven to be equivalent in every way to electrolytic tough pitch copper, suitable for electrical applications. This is accomplished at capital and operating costs which are estimated to be lower than those associated with any other known currently applicable technology. Also, the total energy requirement is equal to or less than any other known process and the process is essentially pollution free."

Jan 1, 1980

By Ali Behrad Vakylabad, Esmaeel Darezereshki, Babak Koohestani

As a by-product of the steelmaking industry rich in iron and zinc, electric arc furnace dust (EAFD) landfill disposal is restricted in many countries due to the metal lixiviation risks. Several approaches have been examined to recycle or reuse EAFD. Hydrometallurgical methods mainly include the preparation of pregnant acid leached solution (PLS) using inorganic acids followed by selective metal recovery using different methods. We herein proposed a hydrometallurgical process initiated by acid leaching and finalized by thermal treatment to produce nano-ZnO from EAFD. At the condition of this study, only 67% of zinc was leached by sulfuric acid from EAFD into PLS while 98% of surplus leached iron was removed through precipitation by sodium hydroxide. Additional purification of iron removed PLS was accomplished using di-2 ethylhexyl phosphoric acid to extract Zn+2. The addition of ammonium hydroxide to purified PLS provided (Zn(OH)2)3(ZnSO4)(H2O)5 as the final precursor for nano-ZnO that ultimately transformed to nano-ZnO (60 ± 6 nm particle size) at 850 °C. The achieved results were scrutinized through various tests and analyses including TEM, XRD, SEM, EDS, FTIR, and TGA.

Mar 10, 2021

By C P. Gravenor

In 1953, a deposit of sedimentary oolitic iron ore was discovered in the Clear Hills area of northwestern Alberta. Since that time, detailed drilling has outlined reserves in excess of 200 million tons of ore grading 30 to 35 per cent iron. Attempts to physically beneficiate the ore to meet blast furnace or direct reduction feed specifications have been, in general, unsuccessful. In 1960, Premier Steel Mills Limited and the Research Council of Alberta jointly sponsored a pilot-plant test at the R-N Corporation at Birmingham, Alabama. About 5,000 tons of ore were treated, and briquettes containing 90 per cent Fe were produced, with 83 per cent recovery. At the same time that the R-N tests were being made, the Research Council initiated a program to produce high-purity powders by chemical methods. Several purification techniques were investigated; hydrochloric acid dissolution of reduced ore was finally adopted. Briefly, the steps involved in this acid process are as follow

Jan 1, 1964

By J. K. Grunig

A process consisting of leach, continuous countercurrent decantation, resin-in-column ion exchange, evaporative crystallization of beryllium sulfate, and decomposition of the sulfate was developed for Spor Mountain, Utah, ores. The process is metallurgically sound, has a minimum of process steps, and is applicable to a wide variety of beryllium ores. The most novel aspect of the process is a resin system of ion exchange which is highly selective for beryllium and which rejects substantially all impurities except for minor amounts of aluminum, magnesium, fluorine, and sulfate in addition to beryllium. The oxide from sulfate decomposition meets specifications of potential users.

Jan 1, 1982

By Toshiaki Akahoshi

Keywords: Wasted catalyst, Hydrodesulfurization, Ammonium vanadate, Ammonium molyb-date, Hydrometallurgical process. The fundamental reactions have been investigated in order to develop a hydrometallurgical process for recovery of molybdenum and vanadium from wasted catalysts generated in the hy-drotreating desulfurization of heavy oil. The principal steps of the process are a mild oxidation roasting of the waste catalysts at temperature around 500°C, leaching of the target metal components with dilute ammoniacal aqueous leachates, selective precipitation of vanadic acid, and ammonium molybdate precipitation. The selective recovery of vanadium as vanadic acid is successfully performed using ammonium sulfate as a salting-out agent. Recovery of ammonium molybdate is based on large dependence of solubility of ammonium molybdate in ammoniacal solutions upon temperature and ammonium salt concentration. In this process, the solution after recovery of vanadium and molybdenum is recycled to the leaching stage of the roasted materials, and the ammonium salts in the process liquor is in the repeated use. Employment of am-moniacal system makes it possible to operate the roasting at much lower temperature than that for the currently operating process.

Jan 1, 2005

By J. H. McNamara

A process has been developed for the successful hydrometallurgical extraction of copper from sulfide ores. The extracted copper in the form of a salt is converted by reduction to copper metal. Purification of the metal is described which includes a description of the casting of ETP quality copper wire bars.

Jan 1, 1978

By T. Rigg, J. N. Stone

"The process described has been developed to utilize low-grade scrap -turnings, borings, tin cans and other types of ferrons scrap which currently has been of limited or no use in conventional steelmaking processes. If scrap of this type can be converted into high-purity iron by chemical means then there is a potential saving of several million tons of metal annually in North America.The process is chemically quite simple and consists of dissolving ferrons scrap in hydrochloric acid, followed by evaporation and crystallization of the resultant solution to yield ferrons chloride crystal.s. These crystals are dries, briquetted and converted to non sponge by reduction in hot hydrogen. The HCl produced from the reduction step. is absorbed in water and the hydrochloric acid so produced is returned to the dissolver circuit. The hydrogen produced from the initial dissolution of the scrap is used to reduce the ferrons chloride. Purity is maintained by bleeding off impure chloride solutions from the evaporator-crystallizer circuit, and converting these chlorides to oxides and HCI in a high-temperature spray roaster. The HCl produced in the roaster is absorbed in water and the hydrochloric acid returned to the dissolver."

Jan 1, 1970

By C. Lupi

In 1996 the Italian Agency for Environmental Protection (ANPA) has initiated a study of the environmental impact of the industrial sector of steel produced by Electric Arc Furnace (EAF). Within the framework of this study a hydrometallurgical process to treat EAF dusts was considered and developed. The paper describes the zinc and lead recovery from fumes coming from carbon steel production. The zinc extraction consists in acidic leaching followed by SX-EW steps. The leaching sludge containing lead sulfates was treated to obtain pure lead salt and inert solid residue. The whole process, that minimizes effluents by recycling the main liquid streams, has been developed to obtain marketable products. The solid waste, containing spinels, was subjected to elution tests in order to verify its compatibility with environmental regulation. The process, that has been set-up and tested in the laboratories of the University of Rome, will be transferred and studied on a pilot plant in order to assess its industrial and economical feasibility.

Jan 1, 1999

By Thomas P. Meloy

"The presence of respirable quartz-bearing mineral par-ticles has been well documented in many coal mines, and the Mine Safety and Health Administration regulations address the quartz content of mine dusts. Unfortunately, the correlation between the quantity of respirable quartz-bearing mineral particles and the pathogenicity of the dust is not strong. Work is currently underway by the National Institute for Occupational Safety and Health/U.S. Bureau of Mines and work is being included in the Respirable Dust Center Program by Dr. Seehra to determine the surface availability of quartz in mixed composition mine dusts. However, this paper propose a possible source of surface quartz or a spe¬cial region in the coal that may contribute to the pathogenicity of selected particles in the respirable dust.Assumed in this model is the hypothesis that either the cleat surface is coated with quartz or some cytotoxic sub-stance that in the body is capable of destroying macrophage and thus inducing a fibrotic response (1) that during the frag¬mentation a reasonable proportion of the respirable size coal particles contain some of the original cleat surface and that these particles have the same order of in vivo cytotoxicity as do the quartz particles. It may be that these cleat surfaced respirable size particles are only contributory to the overall pathogenicity of the coal dust, nevertheless, there are enough of these particles to to considered as a potential source of the cytotoxic dust particles.This paper demonstrates that if the cleat surfaces are mineralized with quartz or have a pathogenic coating, then in many mines there will be enough respirable coal dust particles containing some cleat surface to cause a fibrotic reaction. To understand why some of the dust particles contain as part of their surface some of the cleat surface, consider what happens when a beer bottle is broken. While there are a large number of beer bottle fragments, many of the fragments, particularly the larger fragment sizes, will have as a fraction of their surface part of the original beer bottle surface. The model and mathematics of this problem have been worked out by Meloy.(2-4)In the homogeneous IAC model, (2-5) a fragment or par-ticle resulting from comminution is equally likely to occur anywhere in the material being broken. Therefore the probability of a particle of size x having part of the cleat surface in it, p(x), is proportional to x. Thus:"

Mar 1, 1989

By Alexandre Rodizio Bento

A segurança no ambiente de trabalho é primordial para prevenir acidentes na linha de montagem do setor automotivo. Este setor busca cada vez mais a modernização tecnológica aplicada nas máquinas e a qualificação profissional para melhorar e aumentar a manufatura das peças e componentes. Para atender a demanda intensa do mercado é importante garantir o rendimento produtivo constante dos trabalhadores no chão de fábrica. Devido a esta necessidade, é fundamental exigir atenção dos trabalhadores para prevenir condições inadequadas ou acidentes. A prevenção contribui de forma positiva a empresa, com maior produtividade e ao trabalhador com melhor qualidade de vida. Neste contexto, este trabalho apresenta um estudo que aplica métodos de segurança do trabalho como forma de prevenir acidentes no setor automotivo. Os métodos aplicados na linha de montagem são detalhados e analisados para prevenir possíveis riscos de acidentes. Esta aplicação permite atingir os seguintes resultados tais como: minimizar as perdas de horas homem, maximizar a produtividade do trabalhador, reduzir custos com acidentes, melhorar a imagem da empresa perante a sociedade e a satisfação dos clientes.

Aug 8, 2018

By Felipe das Dores Machado

O estudo de simulação do escoamento do aço líquido no distribuidor requer não somente um grande conhecimento técnico dos critérios de similaridade, mas também uma correta aplicação das ferramentas disponíveis de simulação dos fenômenos físicos envolvidos. A complexidade do escoamento, tendo em vista a interação das inúmeras variáveis envolvidas, torna necessário um estudo dinâmico que utilize diferentes métodos que abranjam a visão de um todo do escoamento, aumentando as oportunidades de uma conclusão mais assertiva sobre os fenômenos ocorridos nas reais condições encontradas na indústria. Este trabalho tem o objetivo apresentar uma nova abordagem sobre a simulação da remoção de inclusões do escoamento do aço líquido em modelos físicos do distribuidor de lingotamento contínuo e como resultado será mostrado um estudo de caso comprovando que a utilização de um único método de modelagem física pode levar a compreensões equivocadas do escoamento.

Aug 16, 2017

By Alexandre Dolabella Resende

O estudo do padrão de fluxo do aço no molde de lingotamento contínuo é de grande importância para a siderurgia, uma vez que permite compreender como as variáveis de processo afetam a qualidade do aço produzido. Existem diversas técnicas, numéricas ou experimentais, utilizadas para realizar esses estudos. Este trabalho apresenta um estudo de simulação numérica, que tem como objetivo avaliar a influência da fração de argônio injetada no sistema no padrão de fluxo do aço no molde de lingotamento de placas. As condições de processo simuladas foram obtidas de diversas máquinas de lingotamento, com diferentes vazões de aço e argônio injetado. Os resultados numéricos foram validados através de um método experimental denominado “Nail Board”. Após a realização do estudo, foram constatadas consideráveis alterações do padrão de fluxo devido à variação da fração volumétrica do argônio injetado no sistema.

Aug 17, 2017

By Thiago Viana de Oliveira Turra

Foi estudado o comportamento do resultado de dureza com o acréscimo de tempo de patamar de tratamento térmico para alívio de tensões, em juntas soldadas com processos MAG e TIG. Utilizou-se o metal base ASTM A743 CA6NM, um aço inoxidável martensítico usado na fabricação de rotores para geração de energia hidroelétrica, e o consumível de soldagem AWS A5.9 ER410NiMo. No processo MAG, foi usado o gás mistura de 96% Ar + 4% CO2, e no processo TIG o gás 100% Ar. Para cada processo, foi soldado um corpo de prova, que foi cortado em sete fatias ao longo do comprimento. Observou-se redução na dureza do estado “como soldado” para o primeiro ciclo de oito horas de patamar. Nos demais ciclos a variação encontrada não tem significância dentro da dispersão da amostragem.

Oct 30, 2017

By Olívia Cristina Petriz Monteiro

A Companhia Siderúrgica Nacional (CSN) possui uma Oficina de Manutenção Mecânica Central que fornece serviços de reparo, fabricação e manutenção de conjuntos mecânicos e componentes. A usinagem é um dos setores de maior demanda durante o reparo na Oficina e é considerada o grande gargalo entre as etapas de reparo/fabricação. Na busca por uma melhora na qualidade do atendimento e dos serviços prestados, o trabalho teve como objetivo identificar e implementar um novo sistema de medição para o Controle de Qualidade da Oficina Mecânica, reduzindo a demanda de inspeções dimensionais e geométricas para o setor de Usinagem. Com a compra dos instrumentos de medição tridimensional, o Laser Tracker e o Braço de Medição, foi possível aumentar a disponibilidade da usinagem, diminuir o tempo de inspeção de peças, acelerar o processo de decisão dos reparos, reduzir o tempo de entrega dos equipamentos, aumentar a confiabilidade das inspeções, além de e efetuar eventuais serviços de medição em campo.

Aug 8, 2018

By William Gleason

"It has been more than 10 years since Montana Resources’ copper/molybdenum mine has had a lost-time injury at its site in Butte, MT. With more than 350 employees and an average production of about 15.5 Mt/a (17 million stpy), which includes 29.5 kt (65 million lbs) of copper and 4 kt (9 million lbs) of molybdenum, the mine’s journey to a decade of exemplary safety is an impressive feat that has required hard work, commitment and, most of all, leadership from every level of the operation.It has not always been an easy journey, nor has it been one without scrapes and bumps along the way, but it is one that has produced stellar results. Mike McGivern, vice president of human resources, and Pete Steilman, safety manager at the mine, spoke with Mining Engineering about how the operation transformed from a site that was accustomed to collecting citations for safety violations to one that is now collecting awards for its safety record.Simply put, Montana Resources has made safety a value and the people its top priority.The operations faced many predictable challenges in 2003, when the mine was being brought back online after three years of sitting in care-and-maintenance status. It had been shuttered in 2000 because of low commodity prices and high operating costs, and, in the three years that the mine was idled, the equipment became dilapidated, and some of it was no longer in compliance. Less than half of the workforce returned to the site for the restart, and the team was challenged with getting the gears turning again to produce copper and molybdenum. But the most daunting challenge of all of was keeping the workforce safe during the transition.In the first few years of operation the mine racked up citations from the U.S. Mine Safety and Health Administration (MSHA) at an alarming pace, so much so that in May 2006, Montana Resources received a letter from the MSHA District Office informing the company that the operation was being placed on the Potential Pattern of Violations list due to its excessive citation history and high rate of significant and substantial citations. It was clear that something significant had to be done to change the course of action at the mine."

Oct 1, 2019

By Ernest A. Hersam

IN every commercial establishment,' it is customary and necessary to take inventory, periodically, and to account for profits and detect losses, to achieve productiveness and enhance efficiency. So, too, in the ordered life of every individual, there is the need of periodic introspection. The exercise of the Sabbath for rational thought, the utilization of pause, or rest, from the technique of daily occupation, orient the efforts. These are the constructive opportunities by which we grow always better than we were. Thus, also, there' is need of a periodic analysis of the organizations to which we belong and toward which we con- tribute. So we find' reason for the fitness of our loyalty. There seems to be no half-ground for the engineer. Whatever presumes to bear his name demands either the crushing pressure of his heel or the supporting pressure of his hand.

Jan 1, 1929

By L. A. Arrington-Webb

The International Standards Organization (ISO) 9000 series of quality standards was published in 1987. First initiated by the British in the mid-1970's to assure the quality of British goods and services. ISO 9000 certification demonstrated the capability of a supplier to meet the requirements of the customer. Thiele Kaolin Company has invested considerable time and money achieving and maintaining ISO 9002 certification. Through a regimen of process control and documentation, routine audits, and a commitment to quality management, this kaolin producer continues to be a competitive pigment supplier in a world-wide market.

Jan 1, 1997