Search Documents

By Leandro de Arruda Santos, Lorena Isabela de Oliveira Ribeiro, Jéssica Dornelas Silva, Pedro Damas Resende, João Victor Lucas Amim, Suzanny Cristina Soares Martins, Vicente Tadeu Lopes Buono

O objetivo do presente estudo foi avaliar a resistência à fadiga de duas ligas de NiTi diferentes sob condições de teste controladas por deformação a 25°C por meio de testes de fadiga por flexão rotativa. Além disso, as propriedades mecânicas, térmicas e estruturais dos fios foram caracterizadas por ensaios de DSC, DRX, MEV/EDS e tração. Os resultados revelaram que ambos os materiais são superelásticos à temperatura ambiente e, portanto apresentaram composição basicamente austenítica de sua matriz. Os resultados de ensaio de tração são condizentes com a caracterização térmica e estrutural, pois os materiais apresentam recuperação total de forma após ciclos de carga e descarga em tração. Ambos os materiais são ricos em titânio, um deles apresenta camada de óxido superficial enquanto o outro apresenta acabamento superficial. Apesar das propriedades similares a amostra 1 apresentou média de 77 ciclos até a falha, enquanto a amostra 2 resistiu a 1827 ciclos..

Oct 25, 2019

By Carl Lubbe, Ron Frye, Wayne Curtis, Julie Pecori, Dan Leach

Blasting conducted in the USA using the new Electronic Initiation System developed by Altech has shown that an accurate delay system will benefit the customer. Results from test work clearly showed that improved fragmentation was effected and blast vibration was at least similar to that currently found at the test venue with improvements possible.

Jan 1, 1997

By P. Gelfi, G. Hill, A. Showell, V. Martins, R. Dunne, R. Jenkins

Carbon attrition losses are not usually a prime consideration for CIP equipment selection and CIP plant design. However, the costs as a result of carbon attrition and associated gold lost with carbon can be high. Recorded carbon losses for Newcrest operating gold plants were shown to vary widely from plant to plant. The Tuckabiana plant recorded an overall loss of only 0.3g carbon /t ore which is very low by industry standards. A comparative carbon management study was undertaken by Newcrest to highlight the reasons for the excellent record of Tuckabiana operation compared to other Newcrest plants. This paper discusses the results of the comparative study and high­lights areas of concern with respect to carbon attrition.

Jan 1, 1995

By J. R. Koehler

The failure of yield pillar-based gate mad designs to provide adequate ground control performance is primarily related to the use of "critically" sized chain pillars. A "critical" pillar is one that falls into a range of pillar sizes that are too large to either yield nonviolently or yield before the roof and floor sustain permanent damage, but are too small to support full longwall abutment loads. To directly compare the in-mine performance of critical and yielding pillar designs, the U.S. Bureau of Mines recently completed a field study in a tapering gate road at the Sunnyside No. 1 Mine, Sunnyside, UT. Extreme pillar stresses and associated coal bumps characterize the response to first panel mining of a 16.8-m-wide critical design. Significantly lower pillar stresses, early yielding of the pillar and adjacent panel rib, and an absence of coal bumps suggest that a narrower 12.2-m-wide design more closely approaches proper yield pillar dimensions. Probehole drilling of several 10.6-m-wide pillars revealed low stress levels and substantial pillar and panel rib yielding prior to abutment onset. suggesting a properly functioning yield pillar design.

Jan 1, 1995

By Louis A. Panek

INTRODUCTION AND SUMMARY With respect to the geomechanics aspects, the primary technical objectives in mining by an undercut-cave method are to achieve a controlled, sustained caving of the mineral body and to remove the fragmented ore with a minimum of dilution from surrounding unmineralized rock, while maintaining stability or control of the rock structure around the access openings. The structurally ideal ore body probably does not exist. If the rock mass is so weak as to cave on a short span, it may tend to be too sticky for easy drawing and handling, or create special problems in regard to support of the access openings. If the ore is strong, caving may be difficult and the caved fragments may be of such a large size as to require special equipment for transferring the ore from the caved zone. Given enough time and money to generate data and conduct trials, engineering and ingenuity can devise an appropriate combination of mine layout, sequence of extraction, and mechanical equipment to achieve a technically successful caving extraction operation to meet the foregoing requirements in many types of deposits. The large capital investment involved, however, reduces the freedom to make major changes once the mine development is well under- way, and the penalties for failure to accurately anticipate operating conditions militate against selecting any but the most obvious candidates for mining by an undercut-cave method. The demonstrated capability to extract large, deep, economically marginal deposits by this low-cost, high-volume method of mining provides an incentive to develop a rationale for predicting the cavability and stability characteristics of a deposit prior to mining, so that the undercut-cave method may be extended to a much wider range of mineral deposit characteristics. The ultimate goal is to establish as explicitly as possible the quantitative interrelationships between the measured rock-mass characteristics, the caving span, the size distribution of caved ore fragments, and the sizes and locations of stable access openings. Lacking an understanding of these relation- ships, a designer may readily change some factor in the wrong direction (e.g., excessively reduce the distance between the extraction level and the undercut to increase the convenience of operations for the undercutting crew, increasing the frequency of repairs to the extraction-level support system) or create unnecessary problems elsewhere in the system by introducing a design change that can achieve only minimal improvement in the factor of direct interest (e.g., unnecessarily complicate the ore-transfer system by changing the orientations of the openings, with- out succeeding in the objective of improving the ground support conditions). Although successful predesign is the prime objective, subsequent modifications in mine lay- out and sequence of extraction operations are inevitable. In developing the modified solution, systematic experimentation based on an understanding of the underlying structural relationships, coupled with monitoring measurements of selected diagnostic structural-behavior parameters, can achieve an acceptable solution in a minimum number of steps, which is far superior to the typical operational trial-and-error approach, in view of the cost of implementing each successive change. Since a drill-core sample of ore rock from a successful undercut-cave operation may exhibit a uniaxial crushing strength in excess of 100 MPa, the caving of such a rock mass is now commonly believed to be ascribable to the presence of discontinuities such as joints or fractures throughout the ore body. An essential part of the present investigation was therefore to characterize the natural discontinuities at each of the test sites by measuring their attitudes and spacings. The term "fracture" is used herein in a general sense to include any planar discontinuity without implication as to its suggested mode of origin. Most, but not all, of the fractures are properly termed joints. As a point of departure we may consider the possibility that the rock mass is transected by three families of joints, each family possessing a distinct orientation, such that parallelepipeds of intact rock are delineated by the jointing. Even if cementation is absent between adjoining parallelepipeds, the undercutting of the rock mass will not necessarily initiate sustained caving--owing to the all-around confinement, an arch may tend to stabilize over the undercut unless prevented from doing so by the failures of key blocks of intact rock. Thus, although the jointing can be assumed to weaken the rock mass, creating preferred directions of

Jan 1, 1981

DURING a period extending over about the last two and a half years, the performances of various types of rock drills in use at the mining department of the Zinc Corporation have been recorded as closely as possible. The main objective was the collection of sufficient data regarding internal water-feed hammer drills, when used for the same class of work as the older type reciprocating drill, to enable a decision to be formed on the following points:(1) Whether internal water-feed, hammer drills could efficiently perform the work previously carried out by reciprocating drills without excessive repair cost to the former.(2) If so, was it good policy commercially to eliminate the reciprocating type completely, writing these off together with the accompanying spares, accessories, and solid drill steel, and replacing with internal water-feed hammer drills, with lighter fittings, and the requisite amount of hollow drill steel.(3) What were the best types and makes of hammer drill for different classes of mining work(4) What was the economic aspect of the introduction of the principle of internal water feed to every type of machine throughout the mine.Prior to the strike of workers in May, 1919, Ingersoll-Rand E47 31-in. reciprocating drills had been used for stoping and for the major portion of driving, cross-cutting, and similar work. The accompanying columns and fittings were all 4t in. The drill steel used was solid octagon. Up to 1916 these machines were also used for winzing, after which time jackhamers were more successfully employed. These latter were of the usual types, varying in weight from 40 to' 46 Ib. Ingersoll BCR 430, Holman No. 2 spool valve, Sullivan DP33,. Waugh Clipper 55. These machines were all dry head; the drill steel was hollow hexagon, shanked.

Jan 1, 1923

By Mark W. Booth

THIS paper deals with the subject of inbye power as the mechanical . engineer sees it, and invites discussion, particularly from the electrical engineer. At the outset, it will be necessary to clear the ground a little by some definite statements. In this question of compressed air versus electricity for the transmission of power and driving of machinery in underground workings, we must see that there are definite fields that compressed air on the one hand, and electricity on the other, can fill to much greater advantage than the other, and in which there can be little or no direct competition, at least for the present. It is under conditions where these fields overlap, and as to where the line must be drawn between the two, that the respective merits of each must be considered. Steam was the first means used to transmit power from the surface of a mine to drive underground machinery, and so long as distances were short and means possible to ensure fairly efficient use of the steam, and where the fire hazard was not in evidence, it gave fairly efficient service. I have in mind an instance during my own connection with the mines-a duplex pump at the shaft bottom at Princess colliery, driven by steam, and which used the steam compound and condensing; and, but for the mechanical difficulties, it was a not inefficient proposition. The steam was taken direct from the surface boiler-plant through a line down the shaft, and used directly at the pump, being in effect a straight conversion from coal to steam to work done. It was the mechanical arrangement, and failure of the pump in that direction, that led to its removal and replacement by something better in the way of an electrically driven turbine pump. Given modern mechanical arrangements, such as a steam-turbine drive on a high-speed turbine pump, and all other parts made in accordance with best practice in the art of steam generation and use, a steam-driven unit fully as economical would have been obtained. But the central electric supply station, and all that that means or promises (not always the same), turned the scale against steam.

Jan 1, 1936

By M. L. Requa

IN the fall of 1910, the Nevada Petroleum Co., operating in the Coalinga field in California, determined to drill a number of wells with rotary tools, in order to prove conclusively the relative value of the rotary as compared with the standard rig. At that time, the rotary was but little known in California and its proposed introduction met with considerable criticism on the part of the operators and quiet opposition among the standard drilling crews. There were few men available who were competent to handle a rotary outfit, and these few had had but little experience in California fields. Machines as then built were much inferior to those now used, being lighter in construction and of a poorer quality of material. The shells encountered at depths between 1,700 and 2,000 ft. seemed to be too hard to permit of successful drilling, and at these depths the rig was changed over to standard tools and by them completed. Because of the heavy depreciation, the time lost in converting from rotary to standard, and the comparatively small profit, it was concluded that unless in the future there was some material improvement in rotary rigs, nothing would be gained by drilling with rotary tools upon this property. Little or no drilling has been done upon the property since that time, but in the meantime a large number of men have been trained in the use of the rotary; in fact, many standard-tool men have abandoned standard drilling and, starting in as roustabouts, have become thoroughly competent rotary operators. The improvements in the machinery have been such as to remove many of the objections and the rotary drilling of to-day is in every way superior to that of 1910. In contrast, a well drilled recently by the Kern Trading & Oil Co., in the east side Coalinga field may be cited. The first 2,500 ft. was drilled in 24 days and it is confidently expected that the water string will be set with a rotary at 3,400 ft.-a record obviously far beyond that made in 1910 by the Nevada Petroleum Co.

Jan 2, 1915

By Milka Madahana, John Ekoru

Particulate matter is one of the leading pollutants in the mines and in the communities in the areas near or surrounding the mines. The availability of large Clinical and environmental data sets obtained from the mines has brought about the need to use better approaches to analyze the collected data. Prediction and control of particulate matter concentration in the mining environment is essential in minimizing air pollution and protecting the respiratory health of mine workers. The main objective of this research work is to analyze datasets obtained from a mining area using machine learning techniques which will then be followed by the real-time estimation of dust particulate in the mines. Datasets collected over 8 years in an hourly sampling rate from an open cast mine is cleaned and analyzed for trends and patterns. Artificial Neural Networks (ANNs), Support Vector Machines and decision trees techniques are applied to analyze and predict the particulate concentrate. The estimation of particulate concentration using Artificial Intelligence will significantly contribute toward the development of quantitative tools to be used in correlating of cause and effect of dust concentration in mines. The results obtained in this work will form a sub-unit of a respiratory health monitoring system for mine workers. The system is essential in the collection, analysis, and tracking of mine workers’ respiratory health, thus it forms part of an early intervention system for mine workers. From the existing theory, we expect the Artificial Neural Network will perform much better than previously used classical models.

Jun 25, 2023

By Neil C. Hario

The purpose of this paper is to explore the various designs and design alternates available for large fine crushing plants, and to discuss objectives and criteria upon which these designs are founded. Common practice for size reduction of run-of-mine or run-of-pit ore in preparation for subsequent treatment utilizes a three-stage system. First stage, or primary breaking is generally carried out with jaw or gyratory crushers. The usual output from this stage provides a feed for fine crushing in the size range of 6 to 10 inches. This discussion is limited to the process of fine crushing, and we will further limit it to what is commonly called secondary and tertiary crushing. We define a large crushing plant as one with a minimum capacity of 2,000 tons per hour. Generally, these plants utilize cone type crushers to reduce ore for rod, ball, or pebble mill feed.

Jan 1, 1970

By Z Li, Z Yan, M Yang

Recycled cement paste (RCP) is a kind of CaO-rich recourse, which is separated and recycled from waste concrete. Due to its chemical composition, RCP could partially replace lime as a flux and be loaded into electric arc furnace (EAF) steelmaking process. Rapid RCP assimilation and liquid slag formation have significant effects on EAF steelmaking process. In this study, the dissolution behaviours of RCP and lime at temperatures of 1400°C to 1500°C were investigated using static dissolution experiment. The dissolution rate, interfacial microstructure, as well as dissolution mechanisms were discussed. It was found that the dissolution rate of RCP was much higher than that of lime. RCP could be completely dissolved into slag in 60 secs at 1500°C. The dissolution rate of lime was in range of 3.910-4 g/(cm2ꞏs) to 2.610-3 g/(cm2ꞏs), while that for RCP was in range of 1.510-3 g/(cm2ꞏs) to 4.910-3 g/(cm2ꞏs). As for lime dissolution, a dense layer of dicalcium silicate (C2S) generated at the dissolution interface, and the diffusion of Ca2+ in C2S layer was the limited step for lime dissolution. Some of calcium ferrite could be observed at the interface between lime and C2S layer. As for the RCP dissolution, there is no obvious product layer of C2S formed at the dissolution interface, Fe2+ continuously diffused into RCP layer during the dissolution, and small amount of FeOꞏMgO solid solution generated and gathered at the dissolution interface. The dissolution rate of RCP in EAF slag was quite higher than that of lime, partially add RCP as flux in EAF could accelerate the slag formation process.

Aug 21, 2024

By H. Sevim, M. K. Mohanty, Y. P. Chugh

The economics of “Conventional” and “Advanced Fine Coal Cleaning” (AFCC) circuits for refuse pond reclamation as well as active mine/preparation plant applications have been evaluated. The benefits of innovative tailings management schemes on the profitability of mining enterprises have also been evaluated as a part of this study. Analyses have been conducted for scenarios involving generation of two different product qualities of 5.81%, a quality that was obtained during AFCC circuit operation at SIU, and a more typical 8% product ash. The inability of the conventional circuits to achieve profitability while producing the lower ash content product is revealed from this approach. The spiral-only circuit is unable to produce a 5.81% ash product. A different version of the same circuit involving spirals and column flotation produced the desired product quality but could not maintain profitability. The AFCC circuits on the other hand, achieve net present values greater than $6 million, with return on investment in excess of 50%, in the water-only as well as dense medium mode, with and without tailings management. Addition of tailings management system to any of the circuits is found to enhance the project economics. The comparison of water-only and dense-medium applications of the AFCC circuits indicate a better suitability of the dense-medium circuit for producing premium quality products. Application of AFCC circuits in active mines offer better economics compared to applications in refuse pond recovery operations. The superior project economics are a result of reduced overhead cost and use of existing material handling facilities. Sensitivity analysis reveals the significance of capacity utilization on project economics.

Jan 1, 2002

By S. R. Gilbert, C. O. Bounds, R. R. Ice

"Many ores are upgraded to produce auriferous sulphide concentrates (principally pyrite) which are not amenable to direct cyanidation. Often these refractory gold-bearing concentrates contain undesirable elements such as arsenic, antimony, etc., which present environmental and/or processing problems. The pretreatment techniques most often considered for processing these concentrates prior to cyanidation include roasting, pressure oxidation, chemical oxidation, pre-aeration, and recently, bacterial oxidation. In this paper, the technical performance and economics of bacterial pre-oxidation vs the classical roasting approach for treating a specific auriferous pyrite concentrate are compared. The results provide flow sheets, preliminary operating and capital cost estimates, and rates of return for the two processes and demonstrate the potential advantages of bacterial pre-oxidation. IntroductionThe increased attention that gold has received in the last ten years has prompted mining companies to look for lower grade orebodies. Many of these low-grade ores do not respond well to conventional direct cyanidation recovery techniques. As free-milling ores decline, gold is sought in refractory environments which, ultimately, drive up the treatment costs.There are a number of reasons for a gold ore to be termed refractory, most of which can be identified by thorough mineralogical examination. The mineralogical occurrence of gold can, to a great extent, impact the method by which the ore is treated and, consequently, the capital and operating costs. Gold in a refractory ore can often occur as discrete particles locked in a host of silicate or carbonate gangue, or associated with sulphides or sulphosalts. Depending on its particle size, gold can be liberated and recovered by mechanical size reduction such as regrinding. This approach is most effective for gold in the 10 - 50 micron range. Gold can also be associated with clay, iron hydroxides, or other minerals which tend to coat the gold surface and inhibit the penetration of the cyanide solution, resulting in poor plant recovery. Because of their resistance to cyanide dissolution, gold tellurides and other refractory gold minerals are also responsible for losses to the tailings. For these reasons, it is paramount that the mineralogical occurrence of the gold be thoroughly and accurately determined before selecting a final process flowsheet."

Jan 1, 1988

By George J. Karabin

Over the past few years, the use of fully grouted bolts to support the roof of underground openings has increased dramatically. While conventionally anchored bolts effectively reinforce the strata of over 80 percent of mine workings, the use of resin grouted bolts in areas of severe roof conditions has resulted in a substantial reduction in roof falls and an overall improvement in both safety and production. The Roof Control Group of Pittsburgh Technical Support Center, Mining Enforcement and Safety Administration, has conducted numerous field and laboratory investigations to isolate parameters which contribute to the effectiveness of both conventional and resin bolting systems. Specially developed strain-gamed resin bolts, compression pads and differential sag stations installed during the mining cycle have generated data reflecting the loading characteristics and resulting roof stability associated with each type of support. Additional investigations have produced optimum installation parameters of the two systems including the effectiveness of thrust/torque controls for conventional bolts and various bolt/ hole diameter combinations for fully grouted rods. Theoretical analyses, coupled with the actual field and laboratory findings and numerous installation observations have facilitated basic comparisons of the working mechanisms and failure modes of both resin and conventional systems.

Jan 1, 1976

In Finland fogging in mine ramps is a common problem. Fog forms when warm and humid exhaust air moves upwards the ramp, where the skin temperature of surrounding wallrock decreases to about 10¦C. Changes in fog thickness and lengths of fog-filled parts of the ramp depend at least on climatic conditions outside, diesel equipment usage in the mine, and the length of working sequence at a time. In this study fogging problems in three different mines, namely Orivesi mine, Louhi mine and PyhSsalmi mine, with different ore types, different layouts, and different depths are presented and compared. All these mines use diesel equipment and the ramp is used as an exhaust air route. In two of these mines the ramp is used as a haulage road and in the other for supply and repairing, checking, and surveying purposes. Measurements of humidity, temperature, air velocity, and dust content were performed in these mines. The measurement results, as well as field observations are presented, compared, and discussed. The results show that fog is observed in areas with high relative humidity values when air temperature and dew point temperature are less than 3¦C apart from each other. Air velocity values were high in many areas. In addition, measured particle concentration values were mainly high in areas, where fog was observed. A short literature review of recent fog formation studies is also presented. It demonstrates the complicacy of the fog formation process. Similarities and differences concerning fog problems in the ramps are found and presented. As already a lot of new information is gained, the continuation of research is considered plausible to find more economical ways of solving and preventing this problem in the future.

Jan 1, 2005

By J Loimi, P Minkkinen, T Korpela

The head loss caused by metallurgical sampling for slurry streams can be reduced by metallurgical sampler design. When the process volumetric flow rate is reduced by vertical static cutters before the sampling by an equal number of moving cutters to the static cutters, the installation requires less installation head space than other sampling arrangements and is easy to accommodate at suitable locations in the process. Low head loss reduces building costs for the processing plant and operational costs during the lifetime of the plant.The presence of a possible systematic bias in the particle size distribution, solids density and elemental composition between an Outotec MSA 2/50 metallurgical slurry sampler sample and MSA 2/50 manually sampled reject have been studied by a customer. The paired samples were taken as simultaneously as possible. The customer evaluated the possible bias using a paired t-test and provided the assay results to Outotec for further evaluation.The results of the paired t-test showed no systematic bias in particle size distribution, solid density or assayed analytes, except in one analyte with low content and a high relative error. The high relative error in one analyte may have been caused by the same calibration model used in a X-ray fluorescence analyser for both high elemental-content concentrate and very low elemental-content tailings samples. The sampled stream is the tailings of a previous process stage.The results of the t-test were studied further using analysis of variance to reveal the error sources in samples. The results showed no bias between the samples collected from the MSA 2/50 reject and composite samples collected of the MSA 2/50 sample stream. The courier online analyser data was also available for evaluation of representativeness to the process stream.The analysis results of the courier online analysis reveals no bias between the MSA 2/50 reject samples, MSA 2/50 sample stream composite samples and online analysis results during the comparative sample collection period.CITATION:Loimi, J, Minkkinen, P and Korpela, T, 2017. Comparative evaluation of manual sampling and Outotec MSA 2/50 metallurgical slurry sampler, in Proceedings Eighth World Conference on Sampling and Blending , pp 167–172 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By James F. Archibald

A research effort has been undertaken, under WSIB sponsorship, to characterize the support capabilities of conventional and innovative spray-on lining materials for mitigating dynamic failure effects created by simulated rockbursts. Conventional spray support media, such as shotcrete and fibrecrete linings, and a variety of new spray-on lining materials (TSL?s), typically polymer-type thin coatings, were subjected to simulated rockburst influence. For baseline comparison, conventional rockbolt and boltand- mesh support products were also evaluated. Observation of lining performance was undertaken through completion of field scale support and rock detonation trials. Controlled blasting tests were conducted at the Queen?s University Explosives Laboratory to examine the effectiveness of the variety of surface coating agents for modifying dynamic rock spalling processes. All tests were performed upon largely undisturbed and homogeneous rock materials in highly repeatable fashion. Both conventional and innovative TSL-type surface lining materials were subjected to ?rockburst? exposure in rigorously-controlled blast trials. All blasts were observed seismically and photographically to provide detailed information concerning rock motion, surface fracturing, ejected fragment motion and support liner survivability characteristics. These material comparison trials were performed to assess the relative effectiveness of a wide range of currently-available area support techniques for suppressing hazards associated with dynamic rock ejection. The results of this study validates that thin, sprayon linings may be equally as effective, and often better, than conventional support materials at mitigating rockburst or like damage in highly stressed mine environments.

May 1, 2003

By Christiana Mystrioti

Greece is the only EU country with extensive nickel laterite deposits. Since the 1960s, the Greek laterites are treated for ferronickel production via a pyrometallurgical route, which involves pre-reduction of the ore in rotary kilns and reduction smelting in electric arc furnaces. Due to the rising cost of energy and the decreasing grade of mined laterites, the pyrometallurgical treatment is economically marginal. For this reason, alternative treatment processes are currently under investigation. Potential applicability of hydrometallurgical treatment, using either H2SO4 or HCl, under atmospheric pressure conditions, for Ni and Co extraction from two low grade laterite ores, was examined in the present work. The two samples were selected to represent the different mineralogical composition of the saprolitic and limonitic ore deposits of the Greek laterites. The investigated parameters were temperature (65–90 °C), acid concentration (1–4 N) and solid to liquid ratio (10–30% w/v). The results indicated that HCl was more efficient than H2SO4 for the treatment of the saprolitic ore; Ni and Co extractions were very high for both elements, up to 98% and 96% respectively, while H2SO4 could leach efficiently Ni, up to 100%, but extracted only 34% of Co. Hydrochloric acid was also more efficient for the treatment of the limonitic ore, with Ni and Co extractions up to 98.3% and 87.6% respectively. With H2SO4 the maximum extractions were 71.3% for Ni and 52.1% for Co.

By William J. Cavanaugh

In 1967, Lone Star Industries, Incorporated, established a program to carry out the necessary Research and Development work to bring the Snyder Process to commercial application. The purpose of this paper, is to present the detailed metallurgical results gathered in comparing the Snyder Process of Comminution to conventional grinding techniques for the milling and beneficiation of certain ores and other materials. The ore primarily dealt with in this paper is a fine-grained magnetite ore, containing approximately 23% acid-soluble iron, from the Lake St. Joseph ore body of Steep Rock Iron Mines, Ltd., (Canada). This particular example was selected for presentation in this paper because extensive comparative results with conventional methods of grinding were available. Also briefly described in the paper are the comminution of other ores and materials such as porphyry copper ore and alumina.

Jan 1, 1973

By P. B. Liebermann

THE resistance to motion offered by mine cars is caused principally by: Rolling friction, flange friction, bending rails, bearing friction and wind resistance. With proper construction and with a fair amount of attention and care, that is, under favorable conditions, the first three items cannot be greatly improved. The wind resistance ordinarily is negligible on account of the slow speeds commonly used. The bearing friction, however, is a variable item, depending upon the design, the bearing material, the lubrication, the location (whether in wheel-hub or on car-body) and the alignment. Under the most favorable conditions the bearing friction will reach a lowest possible value. By the development of a successful anti-friction mine-car bearing this lowest value has been improved to such an extent as to affect the whole system of mine haulage. After being satisfied of their durability and certainty of operation, any investigation into the advantages of anti-friction bearings for mine cars will have to be based upon reliable information as to the saving in power of such bearings. While numerous tests have been made in this direction, the results have not always been convincing, principally because of the rather crude methods that were employed. These crude methods are the main cause of the wide variations existing in regard to the exact amount of the frictional resistance. Frequently an ordinary spring balance is used and the pull necessary to move a certain car or train of cars is obtained by a number of readings. Such spring balances necessarily have a coarse graduation and the continuous vibration and fluctuations to which they are subjected make them highly dependent upon the individual observer. Further, they must be frequently calibrated. Sometimes these tests were made without regard to acceleration, speed or even grade.

Jan 6, 1916