Search Documents

By J. van Deventer

Testwork was done with two different adsorbents, Dowex-Minix gold-selective resin and activated carbon, to detemine their relative performances with regard to gold recovery from clarified low-grade solution employing a fixed-bed operation. The mill discharge from the milling-in-cyanide operation at a Witwatersrand gold mine was used as feed to the adsorption columns. A small amount of gold was leached during the milling process, so that this solution simulates, to a certain extent, a low-grade solution representative of a heap-leach operation. A speciation of the feed solution was done to establish which metal complexes were present in the milling-in-cyanide solution. This information was necessary to interpret metal loadings on the resin, as base metal cyanide species and their respective charges have an effect on the final gold loading capacity of the resin. Equilibrium isotherms were established for both adsorbents to estimate the rate of adsorbent flow anticipated for this specific feed solution. Breakthrough profiles were obtained at two different superficial linear velocities for each adsorbent. Mass transfer zone heights determined from the test work and the elution/regeneration time requirements were used to size a 150 m3/h full-scale plant for both adsorbents. A counter current configuration of adsorption columns, using three columns, should be suitable to recover gold effectively and to produce an effluent with a gold concentration below 0.01 mg/l. Based on the results obtained from the breakthrough tests, a preliminary techno-economic comparison was done between the resin-in-solution and carbon-in-solution options for the recovery of gold from low-grade solutions. This study indicated that the capital expenditure for a carbon-in-solution plant would be about 33 percent higher than that of a resin-in-solution plant. The operating expenditure for a resin-in-solution plant is expected to be only 60per cent of that for a carbon-in-solution plant. Keywords: resin-in-solution, carbon-in-solution, heap leach.

Jan 1, 2000

By Setareh Afrouz, Emily Sarver, Cigdem Keles

The resurgence of severe lung disease among US coal miners since the mid-1990s has led to efforts to better characterize and monitor respirable dust exposures, particularly focusing on mineral constituents from rock strata surrounding the coal. A rapid analysis method for silica (quartz) mass using direct-on-filter Fourier transform infrared (FTIR) spectroscopy has been developed, which can also estimate kaolinite, a primary silicate mineral in many coal mines.

Feb 24, 2022

Rhyolitic rocks are volumetrically significant in the eastern part of the Coromandel gold province, yet deposits hosted by rhyolite (Kapowai, Broken Hills, Neavesville, Wharekirauponga and Waihi Beach) are generally low grade and subeconomic, especially compared with andesite-hosted deposits. In contrast, rhyolitic volcanic centres in Nevada host a number of economically significant epithermal gold deposits such as Round Mountain, Sleeper and Bullfrog. The Nevada deposits are associated with 27-20 Ma continental arc volcanics dominated by ignimbrites (eg Round Mountain), or younger 17-9 Ma bimodal rhyolite-basalt volcanism related to extensional basin-and-range tectonics (eg Sleeper). The Round Mountain deposit is localised on a caldera boundary fault and the mineralisation was deposited soon after eruption of the host rhyodacitic ignimbrite. In other Nevada deposits, hydrothermal systems are linked to the closing stages of flow-dome complexes and mineralisation is localised along normal faults associated with extensional basin-and-range tectonism. The style and composition of the mineralisation is similar in both the Coromandel and Nevada deposits and consists of sheeted and stockwork quartz veins, containing electrum as the main ore mineral and only minor sulphides (mainly pyrite) Likewise, the vein minerals were deposited from low salinity hydrothermal fluids in the temperature range of 200-270¦C. Both the Neavesville and Round Mountain deposits are geochemically anomalous in molybdenum. The deep oxidation of the Nevada gold deposits, dry climate and low level of competing land uses combine to make it economic to mine and process very low grade ore (0.2 - 2.0 g/t Au) by heap-leaching with cyanide solutions in most areas of Nevada. Although extensive low grade gold mineralisation is known at deposits such as Wharekirauponga and Neavesville, it is sub-economic because of shallow oxidation and land use conditions that are unfavourable for open pit mining and heap leaching.

Jan 1, 1996

By Y Lin, B J. Seligmann, M Hassall, S Micklethwaite

For multi-site mining companies, checking the quality and consistency of the data recorded in risk registers is important for confirming how well mine safety management systems have been implemented. However, this task is complicated by the differences in scope of the site, their particular nature, the complexity of the operations and many other factors that can introduce nuances to the characteristics of the risk registers. We present here an application of a technique called Causal Network Topology Analysis for comparing the quality and consistency of risk registers. By quality we refer to, for example: - missing causal relationships between risks - location of missing controls - focus of risk treatment strategies: prevention versus mitigation controls. By consistency we refer to how causally interdependent are the risk events. There are often causal interactions between the lines of a risk register that mean that the likelihood and consequence scores that are applied to each risk event are not independent. We measure this degree of interactions by: - proportion of independent scenarios per register - efficiency of risk treatment strategy comparison. This approach can indicate quality and consistency differences between registers irrespective of the actual details of the site or operation. This occurs by comparing aspects of the structure of a causal network extracted from how the risk events, causes, controls and consequences causally interact. In this work we compare pairs of registers to demonstrate the approach.

Apr 16, 2024

By Peter Grawenhof

Universal joint shafts and slipper spindles are commonly used in rolling mills to compensate the design- and process-related offset between the motors and work rolls. Although both types of shafts exhibit on the same kinematic principle, there are basic differences regarding the design concepts. These differences become noticeable on many levels and may become very distinct in terms of Life-Cycle-Costs (LCC). In this respect, a critical comparison between universal joint shafts and slipper spindles can be made.

Aug 16, 2017

By Peter N. Yanker

The two types of dryers used in the drying of copper concentrates are the rotary dryer and the spray dryer. The rotary dryer has until recent history been the traditional drying method used, Although spray dryers have been used in the chemical field for many years it is only recently that they have been accepted for drying of copper concentrates. The comparison made here will apply in a narrower sense to the drying of copper concentrates as fed into the reverbatory furnaces of the Smelter. To compare a rotary dryer and a spray dryer, which are two totally different methods and pieces of equipment, it is best to view them as systems each made up of certain elements

Jan 1, 1976

By J. G. Craig

This paper initially was to be on the design, construction and operation of the Lucky Friday mill. However, this subject has been pretty well covered in some of the mining publications in the past few years - specifically Mining Congress Journal for April, 1961 and Mining World for March, 1962- : In order to avoid too much repetition, we decided to present in this paper a comparison of the Lucky Friday mill constructed in 1959, and the Mayflower mill built by us in 1962. During the past three years Hecla Mining Company has constructed two relatively small mills: The Lucky Friday mill at Mullan, Idaho 750 T/day; and the Mayflower mill at Heber, Utah - 450 T/day. These mills were engineered, designed and constructed by Hecla, using principally our own personnel, with very little outside (contractor) labor employed. This paper presents a comparison of some of the interesting features of these mills, and where differences occur, it discusses the reasons for the various differences. It compares such points as the testing program, physical layout of the plant, construction costs, the grinding section, the flotation section, tailings disposal, metallurgy, recovery, grades, operating costs, etc. To help illustrate, and to compare these features, we will project pairs of slides showing each of the two mills. First a little background and history on the properties ---

Jan 1, 1964

By D. K. Denton, J. M. Girard, D. F. Scott, T. J. Williams

Personnel from the Spokane Research Laboratory, National Institute for Occupational Safety and Health, examined an underground pillar at the Homestake Mine, Lead, SD. Investigations involved strain relief and seismic tomography studies in the mine, and ultrasonic velocity measurements on pillar core in the laboratory. Measured octahedral normal stress was 37 MPa (5,366 psi); seismic P-wave velocities averaged 5.2 km/s (17,060 ft/s); and ultrasonic velocities at a pressure of 39.6 MPa (5,750 psi) averaged 6.3 km/s (20,669 ft/s). The difference between in-mine and laboratory velocities is attributed to the attenuation of seismic energy by mine fractures larger and more numerous than those in the samples of core measured in the laboratory. Using these results, researchers hypothesize that pillar rocks have the ability to withstand stress an order of magnitude greater than they currently sustain.

By Mark R. Bowie

Air-fall tuffs have been altered to zeolite via reaction of volcanic glass with local pore solutions at the six localities discussed in this paper. These are in the southern Basin and Range Province of Arizona and New Mexico, and in the Trans-Pecos and Coastal Plain regions of Texas. Zeolitization occurred in either closed- hydrologic, open-hydrologic, or hydrothermal groundwater systems. The tripping Spring Valley (DSV) chabazite in Arizona and the Buckhorn clinoptilolite in New Mexico originated in a late Cenozoic network of closed-hydrologic, lacustrine basins extending from southeast Arizona into southwest New Mexico. At DSV, two potentially commercial chabazite-rich tuffs are interbedded with lacustine mudstone. The main zeolite tuft contains up to 90 percent chabazite. The upper zeolite tuff averages approximately 67 precent chabazite. At the Buckhorn deposit, two clinoptilolite-rich tuffs are interbedded with lacustrine m udstone in the upper part of the Gila Conglomerate. The lower zeolite tuff contains up to 90 percent clinoptilolite. The upper zeolite tuff contains over 60 percent clinoptilolite. The Casa Piedra clinoptilolite is in the Trans-Pecos region of Texas. It formed during the Tertiary in a closed basin containing a playa lake. The Casa Piedra tuff averages about 60 percent clinoptilolite. Air-fall tuffs of the Cuchillo Negro, New Mexico and Tilden, Texas clinoptilolite deposits were zeolitically altered by either percolating ground waters in open-hydrologic systems or locally by ponded, saline, alkaline solutions. Cuchillo Negro tuffs are Tertiary and average approximately 50 percent clinoptilolite. Clinoptilolite-rich tuffs of Ebcene age have been mined from four quarries at the Tilden deposits. Tufts from the Kuykendall and Buck Martin quarries contain approximately 50 to 60 percent clinoptilolite. Low temperature, SiO2 - rich, hydrothermal solutions altered air-fall tuff to clinoptilolite and chabazite in the Foster Canyon area of the Tertiary Cedar Hills and Seldon Hills volcanic-vent zone in southcentral New Mexico. Poster Canyon tuffs contain up to 60 percent zeolite and average 40 to 50 percent clinoptilolite. The dominant mineral in the zeolite tufts at the six deposits studied is generally microcrystalline and either chabazite or clinoptilolite. Lithic fragments, unaltered volcanic glass, other zeolites, quartz, calcite, opal-CT, cristobalite, feldspar, evaporites, clays, and mafic minerals are also constituents of the tufts.

Jan 1, 1987

By J Rayo

Andean countries (Chile, Peru, Bolivia and Argentina) have 42 semi-autogenous mills (SAG) in operation and there are more than 30 projects in the pipeline that consider SAG mills. At the end of the next decade, the total amount of SAG mills in this area will likely be close to 100.There is a lot of reliable operational information collected by JRI Ingenieria Sociedad Anonima, the author’s engineering company, for more than 20 years and processed by statistical software, to be used as a reference for design basis of future projects or to improve operations by comparison. JRI Ingenieria Sociedad Anonima has reliable information related to the performance of more than 50 per cent of the Andean SAG plants.The paper presented considers a set of graphs that summarise the collected and verified SAG plants technical data. The figures will show key parameters as circuits and equipment data, energy consumption, technical availability, utilisation rates, throughput variability, pebble productions, steel consumption and others.The data is compared with typical design basis of several engineering companies and the main differences are analysed and/or commented on.CITATION:Rayo, J, 2014. Comparison of semi-autogenous mills operations in Andean countries, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 283–296 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By E. F. Nelson

The 1970s have witnessed the completion and successful start-up of several new non-ferrous metallurgical operations in the Western Hemisphere which utilize large semi-autogenous mills in the grinding circuits. These facilities' are arranged either as single-stage circuits, or in a two-stage configuration n with ball mills. Another major concentrator, designed with an autogenous mill, ball mill, crusher (ABC circuit), is presently under construction and scheduled for start-up late this year. The large primary mills employed in these circuits have high diameter-to-length ratios and are designed to accept a very coarse feed, i.e., the product of a primary gyratory crusher, or run-of-mine ore. This characteristic obviates the need for a secondary-tertiary crushing plant or, in selected cases, even a primary crusher, which is a basic requirement in feed preparation for conventional grinding mills. This paper discusses three such grinding circuits and, presents operating data for two of them: the Island Copper Mine of Utah Mines, Ltd., near Port Hardy, British-Columbia,- and the Pueblo Viejo Cyanide Leach Plant of Rosario' Dominicana, S.A. on the island of Hispaniola. The design criteria for the Cyprus Bagdad Concentrator under construction' at Bagdad, Arizona, are also included. Data pertinent to these circuits are tabulated in the Summary.

Jan 1, 1977

By Benno Ring

"When designing segmental lining at a cross passage, modern solutions try to bear the loads transferred around the opening within the rings by using shear elements in the ring joints. Commonly used shear systems providing coupling are cam & pocket, shear keys, bicones and steel dowels. These solutions have advantages and disadvantages, but most importantly they have limits in their capacity to stabilize the lining at cross passages. With the help of 3D-FE-analyses for an opening of one segmental ring these different solutions are compared taking various ground conditions into account. As a result the capacity of the individual system is determined. Notice is made regarding the applicability of the system as well as the consequences for the design and the verification. INTRODUCTION The design of the lining at a cross passage is among the most difficult tasks when designing TBM-tunnels. At one time the bedding of the lining disappears due to the excavation behind the lining, at another the ring-structure is interrupted when parts of the lining are removed for the opening. The trick is to transfer the loads around the opening into other segments and to areas of the lining which are still supported by the ground. In the rings immediately at the cross passage this creates a distribution of forces within the segments that strongly deviates from that of the regular lining. The design needs to consider the boundary conditions of the respectively chosen solution for stiffening of the opening and its peculiarities in the modeling as well as in the verifications. In the past segments of steel or an internal strutting of steel (DAUB 2013) placed around the later openings were commonly used, see Figure 1. The application of a strutting from the outside to the rings is restricted to such circumstances when for example a connection from a shaft to the tunnel can be made in suitable ground conditions (Ring and Glomp 2012). Though steel segments provide a robust solution, they are expensive due to their laborious manufacture, the high proportion of construction steel required and the time consuming installation in the tunnel (Häfliger 2013). A strutting of steel requires extensive design and verification. The resulting structure usually weighs several tons and must be erected as well as demounted within the confined space of the tunnel, requiring suitable transport and assembly equipment. The cross section remains restricted, thus causing a bottleneck for TBM operations and hindering the works and installations for the cross passage works."

Jan 1, 2016

By Yanxu Shen, Cheng Liu, Zhijie Chen, Hao Chen, Huimin Gao, Zijie Ren

Fluorite, a kind of critical non-metallic minerals, is the primary source of industrial fluorine. Sodium oleate (SO) is commonly used as the collector of fluorite ores. However, because of its some features (such as the low solubility, high solidifying point, and poor dispersion of SO) at low temperatures, it profoundly inhibits its collecting ability as well as the flotation performance. Herein, we have developed a low-temperature-resistant collector for the efficient flotation separation of fluorite from quartz. The advantages and disadvantages of the SO and sodium petroleum sulfonate (SPS) were analyzed by comparing the performance under different temperature conditions. The results of flotation tests suggest that SPS exhibited much better collecting performance than SO under low temperature. The flotation mechanism of the two collecting agents were further analyzed by contact angle measurements, zeta potential measurements, Fourier-transform infrared spectroscopy (FT-IR), and flotation kinetics. The results indicated that both collectors can selectively undergo electrostatic and chemical adsorption with fluorite, with no adsorption on quartz surface. The sulfonic acid group in SPS is a hydrophilic functional group, which has a relatively higher solubility in water. Therefore, the water solubility of SPS is better at low temperatures.

Sep 30, 2021

By Michael L. Nave

Belt Conveyors are an important method for transportation of bulk materials in the mining industry. The control of the application of the starting torque from the belt drive system to the belt fabric affects the performance, life cost, and reliability of the conveyor. This paper examines applications of each starting method within the coal mining industry.

Jan 1, 1993

By J. Rajesh Kumar

The extraction equilibrium study of tetravalent platinum was carried out using tri-octyl/decyl amine (Alamine 336) and bis(2,4,4-trimethylpentyl) monothiophosphinic acid (Cyanex 302) in kerosene from hydrochloric acid media to investigate their extraction capacity, since they have different donor atoms, ?N? and ?S?. Their distribution equlibria were studied as a function of acid, extractant, diluents and temperature. The title metal shows the inverse behavior at higher acid concentrations. Extraction of tetravalent platinum increases with increase of extractant concentration. The plot of log D vs. log [Extractant], mol.L-1 is linear with slopes 1±0.3, indicating the association of one mole of extractant with the extracted metal species. Stripping of metal from the loaded organic (LO) with mineral acids and bases such as hydrochloric, sulphuric, nitric acids and ammonia, hydrogen peroxide, sodium hydroxide, thio- urea were studied. Regeneration and recycling capacity of Alamine 336/Cyanex 302 and extraction behavior of associated elements was also studied.

Jan 1, 2009

By Asmaa Yassien

Finite element models were developed to study the effect of tensioned and fully-grouted bolts on the stability of the mine opening in a three-entry development system using a typical geological column for the Pittsburgh Coal Seam. The models were used to study the effect of each bolt type on the stress distribution in the immediate roof, yield zone development and the vertical deformations. Comparison of all of those features show that the effect of a tensioned bolt on the stress distribution in the immediate roof is restricted to limited areas, whereas the fully-grouted bolt has a much wider effect on the stress distribution. Both types of bolts can reduce the yielding and deformation in the immediate roof to different degrees. The fully-grouted bolt reduces the sliding along the bedding plane more than the tensioned bolt. Both types of bolts were able to maintain the bedding planes without separation. The induced forces in both types of bolts are analyzed. A rapid increase in the shear force and bending moment occurred in the fully¬grouted bolt due to the relative motion of bedding planes.

Jan 1, 2002

By Matthias Baeßler, Markus Herten, Ernst Niederleithinger, Steven Georgi

"Abstract: BAW and BAM have performed a large scale comparison and calibration test on static and dynamic load capacity evaluation of bored piles in glacial sandy soil. The test was performed using eight piles at the BAM test site for technical safety at Horstwalde 50 km south of Berlin. The test area has been prepared and investigated in great detail using boreholes, cone penetration tests, pore pressure sensors and geophysical methods to assure controlled conditions for all piles and tests. The piles (10 m length, 0.9 m diameter) are mainly friction piles (low toe resistance) and have been checked by integrity testing. Five piles have been tested by five contractors using the dynamic method in a blind experiment, the other ones piles by static load and/or later on by the dynamic method. Some piles have been equipped with additional fibre optic instrumentation which proved to be robust and helpful in interpreting the results of static, dynamic and integrity tests. We have experienced a deviation of the dynamic load test results gathered in the blind experiment from the static values of up to 20% in most cases, sometimes even up to 30%. This can be related to the known soil inhomogeneities, interpretation and modelling in CAPWAP and method inherent uncertainties. In cases where the static values were known by the testers for calibration, the deviations were significantly smaller. It has to be taken into account, that the two static load tests showed different results as well. Due to the low toe resistance, use of a big drop weight (11 tons) and large drop heights most piles suffered from cracking, which was clearly seen in follow up integrity tests and confirmed by excavation. The piles are available for further research.IntroductionBored piles are used in many construction projects of the German waterways authorities, e. g. bridges, piers or locks. Their load carrying capacity varies with pile type and geometry as well as soil type, parameters and structure and is thus not easy to calculate in advance. Dynamic pile testing as a cost effective addition or replacement for expensive load tests is accepted in many places (Beim and Likins 2008) but still doubted in others. Inspired by the international prediction event for piles in residual soil carried out in the frame of ISC’2 (Viana de Fonseca and Santos 2008), governmental research institutes have designed an experiment in a geological setting typical for glacial and post-glacial areas in northern Germany. Some results have already been presented by Niederleithinger et al. (2012), Herten et al. (2013) and Baeßler et al. (2013). It was intended to perform a blind test for load capacity estimation using dynamic pile testing on six drilled shafts involving five test crews. Two other piles would have to be tested thereafter using static and dynamic methods."

Jan 1, 2014

By Ahmad F. Souri, Murad Abu-Farsakh

"In this study, the static lateral resistance of vertical and battered pile groups was analyzed using 3D finite element analysis. The battered pile group finite element model was verified using the results from a case study performed on the M19 pier foundation of the I-10 twin span bridge in Louisiana. The vertical pile group model was created by adjusting pile inclinations of the verified battered pile group model. The finite element models utilized nonlinear constitutive models for materials behavior and a soil-pile interface model. The results showed that the battered pile group had greater lateral resistance than the vertical pile group with 60-70% lower pile cap displacement. The largest lateral load share was found in the middle rows in the battered pile group, while it was in the leading row for the vertical. The soil resistance profiles showed that the vertical pile group mobilized greater soil resistance compared to the battered pile group.INTRODUCTIONThe lateral resistance of a pile-soil system depends on both pile stiffness and soil reaction. The soil reaction is a nonlinear function of deflection, depth, pile stiffness, and soil stiffness and strength. The lateral capacity of single piles is evaluated at the maximum deflection limit, and can be predicted using established methods such as the p-y curve method (e.g., Matlock 1970, Reese et al. 1974), elastic solution by Poulos and Davis (1980), the strain wedge model (Ashour et al. 2004), and the finite element method (e.g., Yang and Jeremic 2002, Comodromos and Pitilakis 2005, Isenhower et al. 2014). For pile groups, the lateral capacity of a pile-in-group is less than the isolated single pile case because the soil in front of the pile-in-group is weakened by the overlap of stress zones from surrounding piles. The latter is referred to as the shadowing or group effect (Fig. 1). Prediction of the lateral capacity for pile groups is based on the p-y curve method for single piles with the use of empirical factors called “p-multipliers”. The p-multipliers accounts for the shadowing effect, and are a function of pile-pile spacing and soil type (e.g., Brown et al. 1987, 1988, McVay et al. 1995). Moreover, the lateral capacity of pile groups is also influenced by vertical load, piles arrangement, and slenderness ratio (e.g., Rao et al. 1998, Patra and Pise 2001, Ilyas et al. 2004, Hussien et al. 2012).Battered piles refer to piles installed at an angle with respect to the vertical to increase their lateral capacity. The greater lateral resistance is achieved by the additional axial reaction in the pile. Battered piles are called “negative battered” when inclined in the load direction, and “positive battered” when inclined opposite to the load direction (Fig. 1). Previous studies concluded that the lateral resistance is highest in positive battered piles followed by negative battered and vertical piles, respectively (Murthy 1964, Meyerhof and Yalcin 1993, Zhang et al. 1999)."

Jan 1, 2017

By Patrick J. Hannigan

A comparison of 40 statically and dynamically load tested piles was performed to evaluate the variation between testing methods. This evaluation indicated an agreement of 10% to 15% could be obtained when the available static resistance is fully mobilized by both methods and when time dependent capacity changes are minimized. Dynamic pile testing recommendations for minimum induced impact force, ram weight to pile weight ratio, and considerations for time dependent capacity changes are presented.

Jan 1, 1987

By Alan B. Wagner

Data from seven instrumented pile load tests in Milwaukee, Wisconsin and two other instrumented load tests reported in the literature, one in Evanston, Illinois and one in Houston, Texas were reviewed. The data were for pipe piles having diameters from 9-5/8 inches to 18 inches, driven to depths between 36 and 96 feet. These data were used to develop a relationship between effective vertical stress and unit side friction and unit end bearing. These relationships were based on readily measured soil parameters, undrained shear strength, Cu, and Standard Penetration Test (SPT) values. This Beta (ß) and Nt approach and four other methods were then used to calculate the bearing capacity of the nine cases analyzed. The results from each of the methods are compared with the measured results.

Jan 1, 1991