Search Documents

By Jun Deng, Daohong Wu, Zhicheng Cao, Jingkun Tang, Luxing Feng, Xun Xue

The effect of reducing temperature, H2/CO mole ratio, and reduction gas flow rate on the metallization rate of oxide pellets were investigated at laboratory scale, with ludwigite iron concentrate used as raw materials. The reducing temperature varied from 850 to 950 °C, the H2/CO mole ratio changed from 1.5 to 4.5, the range of reduction gas flow rate was from 2 to 5 L/min. The results indicate that the metallization degree of pellets increase with increase of the temperature, H2/CO mole ratio, and gas flow rate. However, after temperature rises to 850 °C, metallization degree increases slowly. The effect of H2/CO on the metallization degree is not very obviously with the ratio of H2/CO increasing from 1.5 to 4.5. When the gas flow rate was increased from 2 to 3 L/min, the metallization degree increased greatly from 72.2 to 92.1%. In the flow range from 3 to 5 L/min, the metallization degree was increased slowly. The results obtained could be useful for comprehensive utilization of ludwigite iron concentrate by gas-based direct reduction method.

Mar 1, 2017

With rapid development of Chinese iron & steel industry, it is of significance to intensify the utilization of domestic complex iron ore resources. The tin, zinc-bearing complex iron ores are typical polymetallic and intractable ones because of the complicated intergrowth relations among the multi-elements, and they have not been efficiently utilized, presently. Based on the thermodynamic analysis of iron, tin and zinc oxides reduction by CO, the technological conditions of tin and zinc recovery and pellets preparation from tin, zinc-containing iron concentrates by selective reduction roasting are studied and a new comprehensive utilization process is developed in this investigation. Under the optimum conditions, the tin and zinc volatilization is respectively in excess of 80% and 70%, and the compression strength of roasted pellet is more than 2500 N/P. Moreover, the residual tin and zinc in the finished pellets is below 0.06%. The finished pellets can be used as high quality iron-making burdens for large-scale blast furnace.

Jan 1, 2014

By Song Jiang, Xianzhi Tan, Minjie Lian

"The ground water heat pump system lades underground hot water which can be heated or cooled by heat exchanger in water source heat pump air conditioner. This system replaces the model of heating of air-conditioning by refrigerator and boiler. In this paper, the formation conditions of hot water energy in Shan Dong are analyzed in order to achieve the purpose of energy conservation and emissions reduction by taking full advantage of water resources such as water pouring and return water of beatification during the productive process of underground metal mine. In order to analyze the issue better, the paper points out some ways and methods for geothermal water often used in underground metal mine. This paper also presents the advantages of the technology of water source heat pump that is applied into underground metal mine. Here is a case study of comprehensive utilization of water source in a certain underground metal mine in Ji Ning. This mine, according to its own actual situation, designs heat pump heat exchange system which is used for indoor heating of buildings and bath for staff. It turns out that the system can save 23% water per year, cut down 3.303 million KW electric energy, and reduce 4160t emission of carbon dioxide. It is concluded that the technology of water source heat pump has broad application prospects in underground metal mine. Therefore, the results show that it is an ideal way to change the present structure of cooling and heating source in metal mine.Introduction In recent years, overuse of fossil fuels has posed a grave threat onto the environment, which makes renewable energy a more important status in energy structure. Development and utilization of renewable energy has become an important direction. Water source heat pump technology is to use solar energy stored in water as cold/heat source to convert energy. Currently, this technology has been widely used in some advanced countries. However, due to facers of implementation technology and component costs, there is still a gap in water source heat pump technology between China and these advanced countries. According to (Blum et al 2011) that after in-depth study, water source heat pump technology has developed rapidly in China recently, and the gap is gradually reduced. Groundwater source heat pump system as a kind of high efficiency, energy-saving and environmentally friendly technology in recent years, more and more get the people's attention. At the same time, its practical application has also been rapid development. Based on (Ni et al 2015) that According to the relevant departments of the prediction, the technology will become the 21st century the most efficient heating and cooling technology."

Jan 1, 2017

By Yuanbo Zhang

Zinc leach residues produced by hydrometallurgical zinc plants contain many valuable elements (zinc, iron, lead, gallium, indium silver, etc), while they have not been utilized effectively hitherto. In this paper, a new process of flotation-reduction roasting-magnetic separation to recover these valuable elements from zinc leach residues is developed on a basis of mineralogy investigations of them. The results show that silver concentrate with grade of 4321.6 g/t and recovery of 80.69% have been obtained, using 1750 g/t Na2S as conditioner, 750 g/t ammonium dibutyl dithiophosphate and SN-9 (assistant collector) as combined collector and 100 g/t terpenic oil as frother, if zinc leach residues with 523 g/t silver are floated at pH = 5.0. When the flotation tailings are subjected to reduction roasting at 1100? for 2 h, the volatilizations of zinc, lead and indium are over 96%. After roasted products are treated by wet-grinding and magnetic separation, the grade of gallium and gallium in the concentrates achieved respectively reaches 1805 g/t and 1536g/t, and the recovery of them is high to 94.67% and 93.20%, respectively.

Jan 1, 2006

By Christine P. Viecelli

As Phelps Dodge Corporation addresses the environmental challenges of the 1990's, water management has become a key element in an overall waste minimization strategy. The Phelps Dodge Hidalgo copper smelter has implemented a comprehensive water management program that includes management of both fresh and process water utilized by its pyrometallurgical operation. Two major technological strategies are being implemented. They are the design, construction and operation of a raw water pre-treatment facility to allow increased evaporation within cooling towers thereby minimizing blow down, and the use of a brine concentrator to treat and recycle significant quantities of process water. The end result of this program is a significant reduction in raw water pumped from the underlying aquifer into the facility as well as a decrease in process water which must be impounded or otherwise treated.

Jan 1, 1992

By Henry P. Van Ormer

This paper discusses some basic fundamentals in compressed air system design and layouts that should always be considered in planning or evaluating a compressed air distribution system in Construction and Mining. Often times, mining operations use central air or "power house" type systems that more closely resemble a typical industrial or plant compressed air distribution system. This paper does not attempt to cover this type of system.

Jan 1, 1975

By Marc Piard

In a cool mine, tapping high-pressure lines through reducing valves lowers the temperature beyond remedy. It is the writer's suggestion that, for low-pressure work, law-pressure air ,should be generated in a compressor installed underground adjacent to the work, and that the jacket-water of the compressor should be utilised for re-heating purposes. Such a system of compressed air distribution, designed especially for service in cool mines, is described in the following notes. The suggested system includes a three-wire pole line from the sub-station to the opening nearest to the working face, with a cable connection extending to the latter from the openings; an electrical centrifugal unit; a reservoir excavated in the ground; and a distribution line, re-heated by jacket-water. As regards the reservoir, it may be pointed out that in many mines there are blind or abandoned tunnels that could be used for the purpose. The centrifugal type of compressed air machine is a comparatively new departure, and it was formerly considered that such a machine, operating at less than 1,000 kilowatts per unit, would be commercially impracticable. At the present time, however, these machines are being built in Europe for as little as 400 kilowatts per unit, and as much as 110 lb. per sq. inch pressure. One advantage which these centrifugal machines have over other types is that they may be driven by plain induction motors, without the help of special starters-a consideration of the first importance where the electrical regulations are severe.

Jan 1, 1926

By Robert P. Moodry

It was attempted to revitalize an old sulfide leach dump by increasing the oxygen content within the dump. Compressed air was introduced into the old dump. This was accomplished by drilling 300 foot angle holes into the dump surface with an Aardvark drill which holes are then cased with 1-1/2 inch perforated PVC pipe. Compressed air is injected through these cased holes during a 10 day rest cycle. The second case consists of bedding perforated polyethylene pipe at the interface between the old dump surface and the next Lift of a new dump. Compressed air is then blown through the bedded perforated pipe on a continuous basis while leach solution is applied.

Jan 1, 1976

By Lanny Pasternak

"This article is directed at plant production, engineering and maintenance personnel. Seldom does any industrial operation take the time to study the costs involved in the generation of what is probably their most expensive plant utility energy source.IntroductionIn the typical industrial plant in Canada, a 200 hp, 900 cfm, air compressor costs about $60,000* per year to operate (Fig. 1). In 1989 when BC Hydro embarked on their industrial energy management program Airflow Energy Ltd. were asked to spearhead the “Efficiency Compressed Air” portion of that program with a mandate to perform onsite overview surveys and physical hands-on testing of some 300 selected industrial plants throughout British Columbia for compressor efficiencies and wasteful air leaks (Fig. 2). The program duration lasted until 1995, during which time a tremendous amount of data were amassed relating to equipment types, clients’ operating habits, end-use applications and operating costs.During the past six years, Airflow Energy also performed somewhat similar surveys but on a smaller scale in Alberta, Ontario, the United States and the Republic of China. It was no surprise to find some inherent equipment concerns related to efficiency as well as neglected energy wasteful air leaks, so British Columbia was not alone and the problems appear somewhat universal."

Jan 1, 1996

[ ]

Jan 1, 1938

[ ]

Jan 1, 1938

By Y. Duraisamy

This paper presents the compressibility of tropical peat reinforced with cylindrical cement column. When a cement column installed vertically in peat, its compressibility was reduced because of the hardened skeleton matrix formed by cement particles bonding with adjacent soil particles in the presence of pore water. The effects of diameter, number of columns and cement proportions in cement columns on the compressibility have been investigated in this study. The results indicated that compressibility index Cc and Ca decreased with the increase in diameter of the cement column. Specimens with 45 mm and 60 mm diameter of cement column were cured for 28 days, after which they were subjected to Rowe Cell Consolidation test. Based on the results obtained, it shows that cement columns can successfully reduce the compressibility of tropical peat.

Jan 1, 2007

By S. K. Shaha, A. Gryguc, S. B. Behravesh, B. Williams, M. Wells, H. Jahed

Warm forging to near final product geometry shows promising benefits in terms of microstructure refinement and texture modification. In the present study, Semi-closed die forging was performed on extruded AZ80 magnesium alloy at a forging temperature of 400 °C and various forging ram speeds. Compression tests were performed to investigate the influence of forging at various deformation rates on the performance of extruded AZ80 magnesium alloy. The microstructural analysis showed that the extruded AZ80 possesses a grain structure typical in wrought magnesium alloys, with sharp basal texture. In contrast, the forged samples had a recrystallized microstructures and a spatially varying textures and crystal orientations resulting from the complex flow behaviour within the closed die forging. Furthermore, once forged, a significant increase in the material isotropy, homogeneity as well as failure elongation were observed. An increase in UCS of 9% was observed in the forging direction, while the UCS in the extrusion direction was similar to that before forging. The changes in UCS can be attributed to both the refined grain microstructure and crystal reorientation. Successful microstructure recrystallization occurs for strain rates which traverse several orders of magnitude, and in general, UCS isotropy increases with increasing strain rate. It is believed that forging cause’s grain refinement and texture modification which act to enhance the mechanical performance (UCS, fracture strain and superficial hardness) for the forging conditions investigated in this study.

Mar 1, 2017

By David S. Cahn

For many years the green and dry compressive strengths' of pellets have been, considered as possible criteria of pellet performance during induration. Although widely quoted throughout the industry, little attention has been given to standardizing the unfired pellet compressive strength test or to determining the characteristics of the test. The purpose-of this study was to compare the constant deformation rate test with that using a constant loading rate in addition, the dependence of these tests on such pellet properties as size, weight, and method of balling was to be investigated.

Jan 1, 1967

By Peter J. Scales

The recovery of water for re-use in minerals processing is an important issue in the reduction of water use in mining, as is the dewatering of tailings to reduce the propensity of ?wet? tailings dams. It is common in these dewatering operations to use thickeners whereby polymeric flocculants are combined with the dilute feed to the thickener to aid sedimentation and the subsequent consolidation of particulate materials. Thickeners are the workhorses of water recovery and tailings dewatering and although the basics are well understood, there is still no ability to reliably predict the throughput and underflow density from a thickener based on traditional sedimentation tests and flux analysis. The reasons for the discrepancy between full-scale operations and predictions based on laboratory tests are numerous, including difficulties in mimicking the flocculation conditions experienced in the field and the shear conditions in the thickener. The latter effects are little understood and hard to quantify and include effects due to flocculated aggregate densification, complimentary shear and compressional effects and aggregate break-up. Developing a set of test protocols to quantify the effects of densification, shear in compression effects and aggregate breakup and the subsequent contributions of each to compressional dewatering in a thickening environment has been completed for a simple model polymer flocculated particulate suspension. The data and analysis shows that aggregate densification is a dominant contributor to the difference between observed and predicted behavior based on laboratory tests. A major consideration in the analysis is the fact that common thickener operations are permeability limited and although the various effects are all important, the one that results in the fastest water release is dominant. Of interest also are the shear rate, concentration, and time dependence of the aggregate densification process. A basic model of the process has been developed along with network yielding tests conducted using rheometry. Keywords: compressional dewatering, gravity thickening, rheometry, aggregate densification, raked batch settling

Sep 1, 2012

By M. Hesham El Naggar, Osama F. E. Drbe

"Abstract: The use of micropiles has greatly increased the last twenty years, including applications involving low capacity micropile networks, seismic retrofitting, underpinning of existing foundations and high capacity foundations for new structures. This paper presents a field study of the behaviour of single hollow core micropiles in firm to stiff lean clay. Eight micropiles were installed using hollow bars (76 mm OD and 48 mm ID) with air/water flushing technique and advanced to a depth of 5.75m: six micropiles were installed using 228 mm (9 in) drill bit and two micropiles were installed using 178 mm (7 in) drill bit. All micropiles were instrumented with linear potentiometers to measure the vertical displacement of the micropile head and vibrating wire strain gauges to measure the axial strain at three points along the micropile length. Twelve full scale tests were conducted on the eight micropiles, four monotonic compression, four cyclic compression and four tension tests. Only the results of micropiles tested under monotonic compression is presented in this paper. The full scale load tests and a comparison of the performance of the micropiles with 228 mm and 178 mm drill bit are presented and discussed in terms of load-displacement curves, bond strength and tip resistance. The results showed that the proposed values of bond strength in FHWA give a conservative design of the hollow core micropiles. The micropiles constructed with 228 mm drill bit performed marginallybetter than the micropile with 178 mm drill bit in terms of the ultimate capacity.IntroductionMicropiles have been defined in a variety of ways, but can universally be classified as small diameter (less than 300mm), bored, and grouted in place piles (FHWA, 2005; Bruce et al., 1999; and Scherer et al., 1996). They can sustain axial (compression and tension) and/or lateral loads. Dr. Fernando Lizzi used micropiles in 1952 for underpinning of historic buildings damaged during World War II (Bruce D. A., 1988). Since then, micropile applications have expanded rapidly to include underpinning for existing foundations, in situ reinforcement, and seismic retrofitting and foundations for new construction. In particular, micropiles have graduated from use in low-capacity micropile networks toapplications as single high-capacity foundation.Micropiles capacity is affected by the construction technique, which involves drilling, placing reinforcement, and placing or pressurizing the grout. For example, the drilling method influences the degree of bonding between the grout and the ground, and the placement of reinforcement and the choice of grouting method have an impact on the development of the bonding. Bruce et al. (1997) showed that grout/ground bond is most affected by the grouting method. Based on the type of pressure applied during the grouting process, micropiles are classified as follows (FHWA, 2005): Type A: grout is placed under gravity pressure only using either sand-cement mortars or neat cement grout. Type B: pressures typically in the range of 0.5 MPa to 1 MPa are applied in order to inject the neat cement grout into the drilled hole while the temporary drill casing is withdrawn. Type C: involves two-step process; neat cement grout is first placed in the hole under gravity pressure head only as in type A, and prior to the hardening of this primary grout, a similar grout is then injected via a preplaced sleeved grout pipe at a pressure of at least 1 MPa. Type D: like type C, this type is a twostep process: neat cement grout is placed in the hole under gravity pressure head only (but pressure could be applied in some cases), additional grout is injected via a sleeved grout pipe at a pressure of 2 MPa to 8 MPa once the primary grout has hardened. In some cases, a packer is used inside the sleeved pipe, enabling specific horizons to be treated. Recently, Type E micropile is proposed, which involves"

Jan 1, 2014

By X. W. Yi, Z. J. Li, G. W. Ma

In this paper, the compressive strength and failure patterns of reinforced cemented paste backfill (CPB) were studied aiming to promote the stability of backfilled stopes. The concept of ductile backfill was proposed and a series of unconfined compression tests were carried out on both non-reinforced and reinforced cemented paste specimens. Portland cement (3% to 5% by weight of tailings) and five different types of ductile materials (0 to 0.5% by weight of solids) were employed in this experiment for the specimen preparation. The test results showed that inclusion of ductile materials enhanced the unconfined compressive strength (UCS), reduced the post peak stress loss and transformed the failure behaviour of specimens from classical brittleness to ductility. The strength of CPB reinforced with different proportions of polypropylene fibres was compared. The stress-strain curves illustrated that both cement and fibres contributed to the increase of UCS, but higher strain values at the peak stress were achieved by fibre reinforcement. CT sliced images acquired from X-ray computed tomography (CT-scan) demonstrated that the reinforced specimen developed irregular crevices at the edge of cross sections and gained the capacity of bearing large displacements owing to the mobilised tensile strength of fibres. It leads to the potential of avoiding unexpected falling blocks of CPB when adjacent mining occurs. This finding highlights a strategy to improve the self-supporting capacity of the fill mass with less cement usage and reduce the ore dilution rates when excavating to adjacent stopes.

Jan 1, 2015

By Y. Sugiyama, K. Kitazono, T. Miura, K. Matsuo

"Impact energy absorbing system for automotive is an important technology. Open-cell porous aluminum alloys were manufactured through Powder Bed Fusion (PBF) process. Compressive properties of the porous aluminum alloy depend on the cell structure as well as the porosity. The authors manufactured two ordered cell structures, truncated octahedron and rhombic dodecahedron, and one disordered cell structure, random Voronoi structure using a 3D-CAD software. Compression tests revealed the anisotropic deformation of the porous aluminum alloy with ordered cell structure. On the other hand, the porous aluminum alloy with disordered cell structure showed relatively isotropic and uniform deformation, which is suitable for energy absorbing applications. Therefore, controlling the disordered cell structure designed by Voronoi diagram enables to develop the advanced porous aluminum alloy having various mechanical properties.INTRODUCTIONAdditive manufacturing (AM) process enables to manufacture near net-shape mechanical parts. The AM technology is typically focused on titanium alloys due to their high specific strength and biocompatibility (Attar, 2014). Recently, aluminum alloy parts can be manufactured through selective laser melting method (Leary, 2016). Metal foams or porous metals are lightweight cellular materials having closed-or open-cell structures (Banhart, 2001). Aluminum foams are focused on as an energy absorbing material for transport industries (Baumeister, 1997). The purpose of the present study is to investigate the optimal cell structure of open-cell porous aluminum alloy manufactured through AM process. Most previous researches on the AM aluminum lattice structure has been considered ordered and periodic cell structures. On the other hand, classical aluminum foams manufactured through cast or powder metallurgical processes have disordered and heterogeneous cell structures (Körner, 2000). The authors use a concept of Voronoi diagram (Moukarzel, 1993) in order to manufacture various cell structures."

Jan 1, 2018

By Marc. A. Meyers

The analysis of the phenomena involved in the determination of the compressive strength of iron-ore agglomerates leads to the identification of the important parameters. It is shown mathematically that the pellet rupture strength is proportional to the cross-sectional area. Fracture is initiated at the center of the pellets by the tensile stresses developed by the compressive loads normally to the compression axis. The variation in strength between individual pellets of identical composition and subjected to identical treatments is due to internal voids of varying sizes, that act as stress-concentration sites. Two novel testing procedures are proposed. The first consists of testing the pellets between two plates having three steel spheres each. This configuration simulates much better the environment actually encountered by the pellets. The second procedure consists of a thick-walled cylinder in which a piston penetrates; a large group of pellets is tested simultaneously, as the stress versus strain plot is being recorded. This latter test presents significant advantages over the conventional testing procedure; the main one is that one single test is sufficient to characterize the mechanical response of the pellets.

Jan 1, 1981

By Eduardo Luiz Sales Marinho

A Fábrica de oxigênio da AMT produz gases O2 e N2, utilizados no processo de produção de aço. Neste processo de fracionamento de ar, existe um compressor de ar que é responsável pela captação do ar atmosférico. Este compressor é do tipo centrifugo de 4º estágios de compressão, fabricação Hitachi, e tem capacidades de vazão de 114.000 Nm³/h e pressão de descarga 5.4 Kg/cm². Em Novembro de 2012, foi realizada inspeção no compressor e identificado trincas nas pás do impelidor do 4º st e perda de espessura de parede das pás do impelidor do 3º st de compressão. Houve perda da confiabilidade de operação do equipamento, sendo necessária uma ação para correção do problema. Depois de identificado a causa raiz das trincas,foi decidida a compra de dois novos impelidores com modificações no material para aumentar a resistência à corrosão. Na aquisição dos novos impelidores havia duas possibilidades: 1) Adquirir novos impelidores junto ao fabricante original do equipamento; 2) Adquirir novos impelidores por processo de engenharia reversa (levantamento de desenhos da peça desgastada para fabricação de uma nova) em conjunto junto com empresa especializada. Este trabalho irá mostrar os critérios e considerações que levaram a AMT decidir pela compra de novos impelidores por “Engenharia Reversa”, bem como, suas vantagens e riscos assumidos.

Sep 25, 2017