Search Documents

By Susan G. Bilhorn

A number of studies have been conducted in active and inactive mine environments using continuous monitoring and data acquisition systems to detect various parameters. In addition to the information obtained for research purposes, these monitoring systems can provide a means to remotely collect required information (such as radon daughter concentrations and air velocity) and control various conditions (such as fan operation and air door position) in numerous working sections of an active mine. Selection of detector locations and placement, which are critical to obtain the information and control desired while not inhibiting mine operations and influencing the detector readings, are covered in this paper.

Jan 1, 1984

By Stephen C. Tadolini, Thomas E. Marshall, Cecil Banta, L. J. Prosser, Anthony T. Iannacchione

The Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) endeavors to provide national and world leadership in the prevention of work-related illness, injury, and death. This is accomplished by using a scientific approach to gather information, assemble and create knowledge, then translate the knowledge and results into products and services. These products and services are then delivered to all personnel who can effect prevention. Obviously, the development and use of instruments to monitor mine roof conditions provides an opportunity to execute that mission. In the late 1990’s, based on observations at a number of underground limestone mines, only a few used roof monitors. Subsequently, NIOSH introduced the Roof Monitoring Safety System (RMSS) as an aid to roof inspection beyond traditional visual and sounding techniques. Initial expectations were that by gaining roof movement information, ultimately roof sag rates could provide indications of eventual failure. During this investigation, RMSSs were installed in 13 underground limestone mines in six states and this paper analyzes the data obtained at three of these mines. This paper also provides an overview of the system, data, analysis, and applications relevant to the RMSS.

By Panagiotis (Takis) Katsabanis, Lyall Workman, Jack Eloranta

The reduction of metallic ores to concentrate consumes a great deal of electrical energy. In the past two decades, a number of case studies have demonstrated a beneficial relationship between powder factor and grindability. However, changes in mill performance cannot be attributed to changes in feed size alone. Blasting energy and the distribution of that energy appears to affect subsequent comminution beyond crushing. This experience has prompted researchers to attempt to duplicate and quantify the mechanisms involved. To date, published reports indicate a measure of success. However, the blast engineer and the mill engineer still lack the tools and basic understanding necessary for full drill to mill optimization.

Jan 1, 2015

By William P. Lohden

INTRODUCTION It is recognized that, for a variety of reasons, some companies in the mineral industry today are by no means cash-rich and, in fact, are reporting a growing proportion of long-term debt in their capital structures. A review of recent balance sheets of small, medium-size, and some larger companies, indicates that a fair number still have substantial positions in cash equivalents such as U.S. government issues and other short-term money market instruments. In part, this paper concerns itself with companies which have sufficient cash and equivalents and/or cash generation to internally finance mining projects or expansions but which, for some reason, choose to borrow funds. Misconceptions which appear to frequently underlie so-called "leveraging" decisions are explored in this paper. Also considered arc' those circumstances under which any company, including one that is cash rich, should consider borrowing for a project in an amount beyond what would otherwise be necessary based upon its internal financing ability. I do not attempt to cover the raising of equity capital in public markets in this paper. OVERALL RETURN ON INVESTABLE CASH If you approach an individual with an investment which can be financed from savings, or by borrowing at a rate higher than one is earning on savings, that individual will quickly tell you that to pay interest at a rate higher than is being earned on savings would reduce overall income. Assuming that additional investment opportunities are not currently being considered, the individual concludes that a draw-down on savings, leaving a cushion for contingencies suited to individual circumstances, is the correct financial decision. For reasons discussed later, the simple mathematical logic leading to this conclusion tends to become obscured at the corporate level. When Leveraged Studies Are Inappropriate or Premature Surprisingly, I have heard of a number of companies that could afford to finance an investment solely with internal funds, which have made DCFROR (i.e. discounted-cash-flow rate-of-return) studies not only on a 100% equity basis but also on a leveraged basis. Certainly, a leveraged study would be appropriate if additional projects were competing for more capital than was available internally. Often, however, other projects are not far enough along to warrant a leveraged study and there is some danger that a project may be undertaken because it has an estimated acceptable rate of return, on a leveraged basis, that is not ultimately earned because some of the other projects are postponed or abandoned and borrowing is less than expected. For the above reasons, until it has been determined that (1) borrowing is a reasonable certainty for a particular project and (2) the timing and amount to be borrowed has been determined within a reasonable range of accuracy, I believe it is inappropriate and misleading to calculate DCFROR for a project other than on a 100% equity basis. Even when there are several projects currently competing for funds and borrowing will be required to finance one or more of them, using the common yardstick of calculating DCFROR on a 100% equity basis is a safer method to initially evaluate and compare the attractiveness of the projects. Many companies, whether they would have to borrow or not, will reject projects that on a 100% equity basis do not meet their minimum rate of return standards. Some companies which have to borrow will undertake a project provided the project's DCFROR on a leveraged basis meets its minimum return standards. The danger of this approach is that even moderate shrinkages of estimated cash flows could plunge return below

Jan 1, 1985

By C. Cunningham

The process of initiating opencast blasts through long cables is onerous. An obvious alternative is to replace these with radio controlled firing apparatus. Such devices appear from time to time and with the advance of telecommunications, more are likely to appear. However, there are two crucial and seemingly intractable obstacles to overcome: firstly, the problem of malfunction of the system, which can either fire prematurely or go into a state of suspense in which it is unknown whether firing might unexpectedly occur, and secondly, the problem of terrorism, as such a system could provide the capability for an off the shelf remote bomb. The issues of accessibility and electronic reliability when linked to explosives in a mining environment have to be demonstrated to be adequately covered before serious consideration should be given to these systems, up to now largely confined to military applications.

Jan 1, 2003

By W. M. Colwell

When it comes to the analysis of gold bearing ore, there are literally dozens of variables that contribute to the final "true value" of a given sample. Initial sample selection, splitting size and method, inherent nugget gold, pulverization method, and analytical method variations are but a few. However, it seems that the inherent nugget gold particle is targeted as the primary reason for intra and inter-laboratory variations in assay. The following study will show that this is not always the case. A series of tests were undertaken for the Aurora Partnership-Aurora Project to solve inter-laboratory variations in the analyses of blasthole cuttings. Initial concern was centered on the probability that free gold occurrence was resulting in erratic results for the mine's cyanide shake assays and outside laboratory fire assays. Comparison of fire assay and cyanide shake assay was sporadically consistent with previously demonstrated extraction percentage for the cyanide method. The goal was to delineate the factors that ensure consistency in analyses; implement, where needed, Good Laboratory Practices; and reestablish acceptable analytical method correlation.

Jan 1, 1993

By Robert J. Russell

The importance of grinding as a unit operation in all industry has caused much effort to be expended toward improving the facility with which grinding can be done. Endeavor has continued nearly 100 years to formulate laws governing crushing and grinding. This has not been without controversy. However, grinding is an experimental science and our useful knowledge originates in experience. The recorded experience is grinding history. Today, many types of size reduction equipment, each with variations, are available to industry. Frequently, more than one type of grinding equipment will meet a requirement of grinding. However, an economic evaluation of installation and operating costs generally indicates a preferred type. The selection of grinding equipment requires' a consideration of the purpose in grinding, the characteristics of the material to be ground, equipment available for grinding, and the manner in which it can be applied best.

Jan 1, 1960

By Earl M. Frizzell

This paper addresses considerations for the use of artificial support of pit walls in surface mines, a new project of the Bureau of Mines. Results to date indicate that a polymer-coated cable with embedded grit could provide good anchorage for stabilizing benches and highwalls, and an electronic method of recording discontinuities in the field is being reviewed and developed for application to mining. The objectives of the work in progress are to define the engineering parameters and evaluate the concepts for artificial supports in order to provide safe working environments when pit slopes are steepened to increase ore recovery and reduce overburden handling.

Jan 1, 1986

By R. P. H. Willis, A. G. du Plessis, R. B. Wilson

This paper reviews issues to be considered in choosing primary access and transportation options for platinum and other mines. It proposes appropriate criteria and a methodology for deciding on the optimum primary access option for any particular orebody. Also included are generic parameters that can be used to facilitate the process of choosing the optimal access option.

Jan 1, 2004

By J. R. Budden

The growth and oxidation characteristics of any bacterial culture are ultimately determined by the nature of the sample being treated. The most important parameters in the application of bio-oxidation are bacterial cell number, growth rates, oxygen uptake and rate of oxidation. Cells present in the solution of an established culture were counted directly using a microscope, related to a protein value, and then used to determine the total cell number (in solution and on the solids). Protein determination of total cells enabled the growth rates on slurry to be calculated. The cell number and culture growth is related to the iron and sulphide contents of the sample. To illustrate these considerations a moderately thermophilic culture was used to treat ore and concentrate samples obtained from Australian mines.

Jan 1, 1990

By D. J. H. Walker, W. H. Gibson

The inclination of any pit wall composed of stacks of benches is limited by the overall quality and structural complexity of the rock mass in which the slope is situated. For a bench stack angle that satisfies the stability criteria, various combinations of bench height, bench face angle and berm width can be used in the slope design. The bench face angle and berm width geometries must be chosen to fit the bench stack angle but must provide a berm that will be capable of catching the volume of failed wedge material from the bench faces above. Other considerations for bench height and berm width are equipment size, ore selectivity and blasting design. This paper studies the effects of different slope configurations on slope performance as it relates to wedge stability, volume of rock safely contained on berms, and rockfall. Optimisation of the geometry is carried out based on the need to minimise the volume of failed material which limits the effectiveness of the berm. This will reduce the number of rocks that can continue to fall further, reaching geotechnical safety berms or pit ramps, that put safety of personnel and equipment at risk. For general study it is most effective to investigate and compare the performances of each of a wide range of geometrical combinations of bench height, bench face angles and berm widths that fit a variety of different bench stack angles. These analyses were conducted for a predetermined bench stack height and three different bench stack angles.

Jan 1, 2006

By I. M. Stewart

In a proposed rulemaking regulating asbestos, nonasbestos varieties of Tremolite, Anthophyllite and Actinolite would be excluded from the regulations controlling permissible exposure to asbestos fibers. This proposed rulemaking is perceived as improving the scientific basis of the regulation of asbestos because it recognizes that there are no scientific data, either mineralogical or health related, which support the regulation of nonasbestos Tremoiite, Anthophyllite and Actinolite in the same manner as asbestos fibers. However, the proposed regulation, while representing a major advance in the treatment of AT A for regulatory purposes, does not provide an adequate analytical method for distinguishing between asbestos and nonasbestos particles, nor an adequate description of the regulated minerals. This paper addresses those topics, recommending that OSHA include an appropriate mineralogical definition, and implement a discriminate counting procedure to distinguish asbestos from nonasbestos particles.

Jan 1, 1992

By B. C. B. Pretorius

A heat load analysis of the very hot sub-shaft area of Loraine gold mine situated near Welkom, South Africa, showed. that the heat that needed to be removed to give acceptable wet-bulb temperatures at the working faces could not be done by the normal ventilation air alone, but would have to be complemented with extensive refrigeration. The paper outlines the considerations in selecting the cooling system adopted for this shaft.

Jan 1, 1980

By Edward A. Vitunac

The emerging importance of pneumatic conveying systems for bulk materials is largely due to the economic advantages such systems frequently exhibit when compared to alternate methods. Included in these advantages are relative simplicity, ease of installation, flexibility, ease of maintenance, cleanliness, safety and ease of automation to the degree desired. In general, installed costs favor a pneumatic system when compared to competing mechanical systems if the transporting distances are long or to and from many points. In addition, supplemental use such as cooling, heating, or drying may supply the incremental value required to justify its selection.1 The main disadvantages of a pneumatic system are the greater horsepower required per unit weight of material conveyed, material limits in abrasiveness, and density. In addition, material breakage tends to increase at changes of direction and at any obstruction such as that caused by the imperfect butting of two pipe sections in the conveying line. Classification of the material at the discharge may also cause problems in dusting and segregation. Materials weighing less than 4 lb per cu ft tend to cause feeding and collecting problems although they can be conveyed easily. Material between 4 lb and 20 lb per cu ft can be handled with fewer problems, but flow rate is hard to predict. The 20-60 lb per cu ft range offers best results, whereas materials of over 60 Ib per cu ft tend to drop out of the air stream and settle in the pipeline unless careful pro- visions are made to prevent this.2

Jan 5, 1968

By Edward A. Vitunac

The emerging importance of pneumatic conveying systems for bulk materials is becoming recognized by more persons responsible for materials management as consultants, at the corporate level and at the plant level. They have learned that the economic advantages of a pneumatic system are frequently decisive when compared to alternate methods. Included in these advantages are relative simplicity, ease of installation, flexibility, ease of maintenance, cleanliness, safety and ease of automation to the degree desired. In general, installed costs favor a pneumatic system when compared to competing mechanical systems if the transporting distances are long or to and from many points. In addition, supplemental use such as cooling, heating, or drying may supply the incremental value required to justify its selection. (1). The main disadvantages of a pneumatic system is the greater horsepower required per unit weight of material conveyed and material limits in abrasiveness and density. In addition, there is a tendency to increase material breakage at changes of direction and at any obstruction such as the imperfect butting of one, piece of pipe to another in the conveying line. Classification of the material at the discharge may also cause problems in dusting and segregation. Materials weighing less than 4 pounds per cubic foot tend to cause feeding and collecting problems although they can be conveyed easily. Material between 4 and 20 pounds per cubic foot can be handled with less problems but flow rate is hard to predict. The 20 to 60 pounds per cubic foot range offers best results; whereas, over 60 pounds per cubic foot, materials tend to drop out of the air stream and settle in the pipe line unless careful provisions are made to prevent it. (2).

Jan 1, 1967

By Don Conrad, Tom Friend, Bill Wiehagen, Lynn Rethi

On-the-job training (OJT) is a very common method of teaching job skills. Much of the training is done by experienced workers. This paper discusses small investments that can help improve the effectiveness of OJT. Effective OJT involves some structure and planning in the transfer of responsibility for task performance from the trainer to the novice. Assisting the OJT trainer could involve helping develop up-to-date job analyses and offering strategies for teaching and evaluating job skills. The scope of this paper addresses (1) organizational considerations supporting structured OJT, (2) general strategies for structuring OJT, (3) a typical approach for conducting OJT, (4) characteristics and duties of OJT trainers, and (5) limitations of OJT as a teaching method. Health, safety, and operational skills can be connected through training. Haul truck operator training is used to illustrate some of the concepts discussed in this paper.

Jan 1, 2002

The results of a series of physical model studies of the stability of jointed rock slopes carried out some years ago are described. These models were tested under centrifugal loading. Four ?geological? structures were tested; all had the same joint orientations and strengths, but the relative spacing of the joints was different. The results showed that the mechanisms of failure of the slopes varied for the different models, and the gravitational loads at which failure developed also varied. The following conclusions are drawn from the results of the physical model tests: ?the mechanism of slope failure is by progressive deformations throughout the slope ?the ratio of the spacings between the different sets of discontinuities exerts considerable influence on the slope failure ?in the models tested, the intact material strength had no noticeable influence on the stability of the jointed rock slopes(note that for hard rock, similitude conditions indicate a prototype slope height of 300 to 400 m, and therefore intact rock failure might not be expected under simple gravity conditions, i.e. no tectonic stresses) ?rock slope failures are three-dimensional and in general are not amenable to two-dimensional simplification ?knowledge of the orientations of discontinuities in the slopes does not allow prediction of a unique failure surface, nor of a volume of failure. The volume of failure is determined to a large extent by the plan configuration of the slope.

Jan 1, 2006

By Warren L. Howes

LITERALLY hundreds of designs of mill liners are in use in current grinding operations, varying in contour from smooth to the roughest of surfaces, and in materials from scrap rail to alloy steels. A certain amount of variation in materials can be expected, owing to differences in local market conditions and the character of ores. However, when one attempts to rationalize the designs in current operations of a parallel nature, there is little that can be called standard practice. Designs and opinions of designs are as divergent as day and night. Somewhere in this maze there must be clues to better practice. The purpose of this paper is to examine the factors for consideration in liner design, and to propose a vigorous campaign of exploration in this phase of grinding operations. The paramount considerations in the choice of mill liners for a grinding operation are: (I) durability, in view of the cost, and (2) developed grinding capacity. Because of the strategic nature of grinding circuits in controlling the production of most mining operations,1 grinding capacity usually is the greater consideration. GRINDING CAPACITY Mill liners affect grinding capacity in two ways: (I) by establishing dead space within a mill shell, which could be usefully occupied by live grinding media, and (2) by controlling the grinding action of the media. The extent to which liner thickness affects the potential volume of live grinding media, and thereby the grinding capacity, is shown in Table I. In a ball mill 7 ft. in diameter, for example, an inch of liner thickness reduces ball volume and corresponding grinding capacity by 5 per cent. With grinding capacity at a premium, this makes consideration something more than first cost of liner materials. A low-cost, voluminous material, made extra thick to secure adequate life, can be very expensive in terms of grinding capacity. On the other hand, in increased grinding capacity, a long-wearing material in a thinner pattern can save many times its value. [ ] From the standpoint of mechanics, the function of mill liners is to provide the means of driving or tumbling the load of grinding media. In this respect, an internal-spur gear-and-pinion assembly resembles a rotating mill shell with its contained load of grinding media, the mill-shell liners

Jan 1, 1945

By G Gosson

An important requirement in every geological quality control program is that the identity and grades of the control samples (duplicates, certified reference materials (CRMs), and blanks) must remain æblindÆ to the analytical laboratory. Once the entity to be controlled is aware of relevant details of the control process, such as the identity of the control samples, the objectivity may be lost and the control may no longer be completely valid. Whereas the blind insertion of field duplicates and coarse blanks can be easily conducted at site, simultaneously with the sampling process, the rest of the control samples should be inserted into the batches during or after sample preparation and prior to assaying, in order to ensure a proper assessment of precision, accuracy and assay contamination, independent of the internal quality control of the laboratory. Such a procedure raises the concern that blind insertion of crushed or pulverised material in sample batches prior to assaying could represent a breach in the chain of custody principle, as samples would have to be temporarily returned to the custody of a non-laboratory person in charge of the insertions. In this seemingly conflict scenario, what should we give up? Do we maintain the strict chain of custody, knowing that the laboratory will be aware of the identity of some of the control samples, or that some duplicates will not be true same-batch duplicates? Do we ignore chain of custody issues to maintain the anonymity of the control samples and insert blind same-batch duplicates, CRMs and blanks? Is it possible to do blind insertions without breaching the chain of custody? Current NI 43-101 and JORC requirements, as well as real-world QA/QC and sample security practices, are discussed in light of AMECÆs approach to the solution of this apparent dilemma.

Jan 1, 2008

By J. M. Rios

This paper exposes the reasons that led the Empresa Nacional Minera del Sahara, S.A. (ENMINSA) to the selection of a conveyor belt system for the transport of phosphate rock over a distance of 100 kilometers. ENMINSA was created in 1962, with the main objetive of the exploitation of phosphate rock deposits in the Spanish province of Sahara, in North West Africa. Poor grade outcrops were known previously. A detailed geological research carried over the province led ENMINSA to the discovery of deposits not exposed, and of much higher grade. The sector known as Bu-Craa was chosen as the most promising, and was explored by means of drill holing and shafting. The important amount of information obtained permitted a detailed evaluation of the capacity and grade of the rich ore contained in the Bu-Craa area. Simultaneously with the systematic reconnaissance of the Bu-Craa deposits, ENMINSA developped the study of the technical and economical problems required for the beneficiation of the rock, which comprised five main groups of projects: rock exploitation; beneficiation plant; rock transport from the mine site to the Atlantic coast; storage, handling and loading facilities by the sea- side, and power plant. Once determined the location of the marine loading facilities, which to date are in an advanced stage of construction (figs. 1 and 2), the studies conductive to the selection of the best transport system from the mine to the ocean, along 100 kms. distance were undertaken.

Jan 1, 1968