Search Documents

By Werner Burger

The last decade has witnessed a rapid development and application of slurry and EPB type tunnel boring machines. Both soft ground types are able to excavate tunnels in unstable ground conditions below the water table with positive face support. The most significant component of the excavation process is the cutterhead and tool con-figuration were the excavation and face support meets the geological challenge. The TBM downstream processes cannot take place unless the cutterhead and tools effectively do their job. This paper will review the current state of the art design for both slurry and EPB cutterheads and highlight both common as well as geological specific design features.

Jan 1, 2007

By Ian S. Ross

The emphasis in this paper is focussed on dry bulk car go or the same cargo converted to slurry form for ease of handling. It is this type of cargo which is of primary interest to the mining industry whose products it represents to a large extent. The design problems associated with the handling of liquid bulk and of unitized cargo are sufficiently different to be treated separately. This paper then will consider the port handling facilities of dry bulk commodities as part of a system consisting of (1) the movement of products to the port area, (2) the movement of products out of the port area and (3) the handling of products within the port area itself. Expanding within these three components of the total transportation system, the paper will discuss the various difficulties encountered concerning the mode of transport into the port area and the method of handling product from transport to stockpile. Secondly, and before discussing the port area itself and in order to complete the conditions under which the port must operate, the movement of products out of the port area will be covered dealing with such items as the accommodation of the ship, problem associated with the very large ships, optimum berthing arrangements and the need to consider the various costs associated with the vessel. Finally the paper will review within the port or interface area such items as stockpiles, method of recovery, inventory control and an outline of the common design difficulties encountered. In all cases the relative influence on the total transportation costs of each of these dry bulk transportation system components will be considered.

Jan 1, 1972

By Birger Schmidt

The design of underground nuclear waste disposal facilities poses new problems related to the requirement of long term safety against radionuclide migration. The degree and effects of rock disturbance caused by construction and by the long term thermal effects from the hot waste must be predicted with confidence. Computer modeling can, to an extent, be verified by accelerated near-surface tests. Credible extrapolation to deep, long-term conditions requires successful near-surface modeling verification, proper characterization of near-surface and deep rocks, and successful determination of in-situ stresses. Excavation induced disturbance may be assessed primarily by empirical evidence.

Jan 1, 1981

By P Andersson, P Marklund

Evaluation of different techniques for bottom fill stabilisation showed that frozen fill was the most economical method. In order to test the method a full-scale field test was performed in the Rehnstr÷m mine. The test was instrumented with temperature gauges and extensometers. Before the field test, frozen fill was tested at the laboratory. The mechanical properties of the frozen fill were determined by uniaxial compression and creep tests. A deformation model for the frozen fill was set up. Calculation procedure for design of spacing between the freezing tubes, time for freezing and calculation of the necessary capacity of the refrigeration plant was developed. These procedures were calibrated against the field test. The results of these investigations allow the following conclusions: From a mechanical point of view, frozen fill has excellent properties as a structural member and it also has excellent properties to support itself and the fill above. Methods for the thermal and mechanical design of freeze stabilisation have been developed and found adequate. The need to place the freezing tubes several years in advance of the future sill pillar mining, requires careful long-term planning and accurate documentation.

Jan 1, 1998

A wide range of materials are used in hydraulic backfilling operations and the pipeline flow behaviour of these mixtures varies considerably. It is shown that despite the large differences in constituent materials and flow behaviour, a common approach can be applied to analysing the flow of all hydraulic backfills. This is extended to include a rational design approach for backfill distribution systems. The use and limitations of pipe loop tests as a design aid is discussed. Backfill quality control is identified as a key area where improvement needs to be made to enhance the reliability of backfill system operation.

Jan 1, 2001

Provide mine personnel with a convenient means of determining the optimum installation geometry of roof trusses in bedded roof. Background Mine operators frequently ask the following questions concerning roof truss installations: 1. Where should the bearing plates or brackets be placed or where should the inclined holes be started? 2. At what angle should the holes for the inclined chords or angle holts be drilled? 3. What tension should be put into the inclined chords so as to achieve the most effective results for the effort and expense? Truss hardware manufacturers have responded to these questions with answers based on what seems to work best. While designs based on past experience are frequently reliable, there was a need for a rational approach that could accommodate a variety of conditions. The Bureau has developed a procedure that enables mine operators to optimize roof truss installations in bedded roof.

Jan 1, 1989

By D. G. Mirakovski, B. Krstev

The paper presents models of auxiliary ventilation systems with leaky ducts and algorithms for calculations of pressure loss, air leakage, and volume flow ratio and pressure fans. Two basic models are discussed: 1st model for a duct with leakage through the flange joints; 2nd model for a duct with an equivalent longitudinal aperture. The present analytical system has been successfully applied to developing of computer software named DAVentS. A. sample problem is used to illustrate efficiency and accuracy of DAVents software in solving most common problems in process of designing AVS.

Jan 1, 2002

By Samer Sadek, David I. Smith, Wai-shing Lee, Jeffrey L. Rice, Avelino Alonso

INTRODUCTION East Side Access (ESA) Contract CQ028 is located in the New York City Borough of Queens. The contract involves construction of a 230-meter (760-foot) long open-cut excavation with a permanent deck supporting Amtrak yard tracks over a semi-circular TBM launch wall on the east end, and the 36.5-meter (120-foot) long Northern Blvd. Crossing on the west end. The Northern Boulevard Crossing will be mined under an existing New York City Transit (NYCT) five-track subway tunnel; Northern Boulevard, a heavily traveled five-lane truck route; and an existing NYCT three-track elevated line; connecting to an existing open-cut shaft adjacent to the existing 63rd Street Tunnel bellmouth. When completed, Contract CQ028 will provide access for future Manhattan and Queens tunnel contracts. The footprint of the open-cut was determined by the geometric requirements of the future Plaza Interlocking facility to be constructed within in another future ESA contract. See Figure 1. This paper discusses design risk mitigations for the key elements of the contract, namely the Northern Blvd. Crossing and the semi-circular TBM Launch Wall. PROJECT OVERVIEW The Metropolitan Transportation Authority Capital Construction Company—East Side Access Project for the Long Island Rail Road will provide Long Island commuters with direct access to Manhattan’s East Side via a new rail line between the Harold Interlocking in Queens and Grand Central Terminal in Manhattan. The project connects the unused lower level of the existing tunnel under the East River at 63rd Street to new connecting tunnels in Queens and Manhattan. Contract CQ028 Scope and Construction Schedule This contract consists of the excavation of an open-cut from the east side of Northern Boulevard, through an existing MTA-owned rail yard and into the western limits of Amtrak’s Sunnyside Yard. The contract will connect to a completed open-cut

Jan 1, 2007

Deep level block caving as a mining method is becoming more popular due to the fact that it is the lowest cost per ton underground extraction system. However, many block caves do not achieve their full potential due to draw horizon instability. In this paper five design rules are given to overcome this problem. The design rules described are applicable for slusher and trackless block caves where the operational depths exceed 500 metres.

Jan 1, 1999

By J Hudson

Autogenous (AG) and Semi Autogenous (SAG) grinding mills are the conventional selection for large-scale grinding circuits. It is accepted that these forms of comminution are not the most energy efficient available. This efficiency combined with escalating energy prices, steel prices and the requirement to process larger, lower grade deposits has necessitated that better comminution techniques are found to challenge the dominant position of AG/SAG mills in the grinding circuit. Recent advances in high pressure grinding rolls (HPGR), particularly in terms of roll surface protection have meant that, depending on the application, an economic alternative is available to the large diameter AG/SAG mills. Mining companies now recognise the potential benefits of HPGR and so they need proper assessment in the design of new or upgrade of existing grinding processes. Of course, the answer to the question AG/SAG or HPGR is not straightforward and the impact of the grinding process on the whole metallurgical process needs to be evaluated. Clearly this is a complex decision to make and requires substantial metallurgical knowledge, test work, and objective analysis. The perceived downstream processing benefits will differ between different plants depending on the ore type and processing conditions. The optimal design of the comminution circuit requires that a robust methodology is followed to objectively characterise the ore, size the equipment and determine the downstream processing benefits. The paper gives a brief comparison of the capital and operating costs for both grinding systems, and then outlines the appropriate test work that is required to make an informed decision.

Jan 1, 2006

By Kia Riihioja, Mike Higgins

A major difference between electronic and pyrotechnic detonators is that, in almost all but the simplest of blast layouts, computer software is required to plan a blast using electronic detonators. While it may be possible to program delay times without software, using only the manufacturer’s control hardware, the full potential of electronic detonators can only be realized through software. Until recently, the only software available has been provided by the suppliers of the electronic detonators. These usually have just enough features to create a hole layout and to assign times to the detonators in the holes. The software is also able to communicate only with the manufacturer’s detonators. This means that the client may be compelled to change several parts of the blasting process when a different delay system is adopted, from design through to implementation and reporting, even though these may be sub-optimal at the client’s mine. While many authors have demonstrated improvements in blasting outcomes using electronic detonators, very few have discussed how the delay times were calculated. Where the calculations are discussed, it is also obvious that the delay times must be monitored and re-evaluated as conditions in the mine change. For example, the principles of superposition and scaled distance, burden relief and energy cooperation between holes should be checked constantly for different locations within the mine, changes in rock properties, or even for differences between design and actual hole positions. The most common methods in blast design software to calculate delay times are inter-hole interval, relief contour and direct editing. Although they are simple in concept, they can result in fundamental errors if they are not applied correctly. The software for electronic blast designs should be capable of not just a timing calculation, but also of showing, to some degree, the impact and interaction of the calculated times.

Jan 1, 2004

By Michael Hughes, Selva Selvamohan, Ray Costa

"Cutoff walls are commonly used to mitigate underseepage problems for levee remediation projects. At abrupt changes in seepage cutoff wall depths there is a potential for water to flow around the back of the deeper cutoff wall leading to elevated seepage pressures on the landside that could result in exit gradients exceeding design criteria. This condition is referred to as end-around-effects and is a complex problem that requires detailed and time consuming 3-D numerical modeling to represent accurately. This paper presents a simple approach for assessing end-around-effects using the results of 2- D seepage analysis to determine if lateral extension of the deeper portion of the cutoff wall is required. This simplified approach provides a pragmatic solution to a complex 3-D problem. The presented procedure was used as part of the Feather River West Levee Project in Yuba City, California, to assess end-around-effects at 26 locations. The results showed that wall extensions of up to 100 feet were needed at only 2 locations.INTRODUCTIONAs the lead geotechnical consultant for the Feather River West Levee Project, AECOM were responsible for designing levee remediation works for approximately 35 miles of levee protecting the area around Yuba City, California, and communities to the north and south. Due to land use constraints, seepage cutoff walls were the main remediation alternative selected to address underseepage issues for the project.As part of the design review process, the California Department of Water Resources (DWR) requested AECOM to look at 26 locations along the levee alignment where the depth of cutoff wall changed abruptly from shallow to deep, or vice versa. At these locations there was the potential for seepage pressures to pass behind the deeper section of cutoff wall and stress the blanket layer landward of the cutoff wall. A condition referred to as end-around-effects.End-around-effects involve complex 3-D ground conditions that have traditionally been addressed by laterally extending the deeper section of cutoff wall an arbitrary distance based solely on engineering judgment. In discussions with DWR, AECOM developed a simple procedure to provide a more objective assessment of end-around-effects without the need for detailed and time consuming analysis. This procedure allows the engineer to make an informed decision of whether end-around-effects are a problem at the location of a cutoff wall transition rather than laterally extending the deeper section of cutoff wall an arbitrary distance based on engineering judgment alone."

Jan 1, 2015

By Rimas Pakalnis

This paper describes a focus of work presently being conducted at the Rock Mechanics Research Group at the University of British Columbia. The underhand method under consolidated fill ensures a high recovery under an engineered back that is comprised of cemented rock fill and/or cemented paste fill. This method of mining is generally necessary either due to a weak rock mass comprising the immediate back and/or high induced back stresses. A major concern in the design of sill mats is the loading and strengths associated with the overlying sill mat. This paper reviews past practice coupled with present observations and measurements from over ten(10) mines throughout North America. It outlines areas of concern in terms of design requirements.

Apr 1, 2005

By Nicolas Gatelier, Sophie Laurent, Thierry You

Hard-rock caverns for hydrocarbon storage are a very particular type of underground facility controlled not only by local administrative and regulatory constraints that can be very specific, but also by the possible risks of geotechnical or geomechanical failure. Each such facility throughout the world is a prototype that needs to be adapted to very different site conditions. The straight forward application of design methodologies from relatively similar fields (mines, tunnels) can be very useful, but risks holding back the scientific and technical improvements needed by an engineering industry in full development. Here we look at various case histories and at problems that have been raised where recent attempts at standardization would appear to have been ill adapted, and where storage designers, through experience and judgment, may still provide innovative engineering solutions.

Jan 1, 2015

By G. R. O?Neil

The justification for a "ligand- selective' approach to fine mineral beneficiation via flocculation is established initially. Special emphasis is placed upon the need to identify non-selective, interfering and complicating adsorption effects. Specific strategies directed towards the design and synthesis of complementary selective flocculants are detailed using a number of different polymers and chelating agents as examples. In this regard, the affinity of polymer-bound ligands for metallic cations, ligand concentration, possible modes of attachment, the application of spaced-out ligands and other considerations in the preparation of selective flocculants are highlighted.

Jan 1, 1983

By Chu E. Ho

Field load tests on deep slurry stabilized bored piles have shown that end bearing resistance was unreliable due to soft toe conditions caused by debris accumulation at the bottom of the hole during pile installation. This is true whether bentonite or polymer slurry was used. Skin friction resistance was less affected by the slurry and is more reliable. A design strategy is proposed which ensures that an adequate factor of safety against the ultimate shaft resistance is maintained for any chosen design working load, such that a pile settlement of 12mm would not be exceeded.

Jan 1, 2002

By D. A. Trotter, G. J. Goddard

"This paper describes a method of deciding on various design parameters for a sublevel caving layout. Layout design curves are obtained from the output of a computer optimization program. The program uses mathematical relationships derived from the theory of gravity flow of material to optimize the large number of interdependent design variables which are involved.IntroductionIn the design of an efficient sublevel caving mining system, a large number of interrelated variables need to be considered. Although many papers discuss individual variables, very little exists in the literature to show how these variables interact to achieve optimum results. This can lead to trial and error in sublevel caving design, which can prove costly, particularly because sublevel caving is a mining method which requires integration with sublevels above and below. With no pillars being left, experimental stopes cannot be isolated for study. Unfortunately, the complexity of layout design and the costs associated with trial and error have caused many planning engineers to choose more tried and tested mining methods.Sublevel caving works best to extract low-value ore surrounded by incompetent rock. All phases of the mining method can be highly mechanized, allowing low operating costs and high production rates. Good safety records are achieved, as workers are always in 'good' ground and the method is regular, making it comparable to an industrial process."

Jan 1, 1981

By A Kemp, I Taylor, S C. Lamoureux

Detailed landform designs were completed for six (integrated) iron ore waste rock dumps at a Western Australian iron ore mine site to meet closure objectives and to optimise material movements for closure. The designs were based on specific physical and geochemical properties of waste material and the design was undertaken to enhance long-term stability of the dumps and optimise material movements, and therefore minimise closure cost. Construction of the re-shaped waste rock dumps have been completed. Following construction, surface material characteristics were found to deviate from those used in the design assessment. Materials present at surface following re-shaping were generally finer textured than those sampled for modelling. It is anticipated that the embankment slopes may experience increased rates of surface erosion compared to the rates predicted from modelling and used in design. The finer textured material is thought to be generated from exposing finer material that has migrated into the coarser matrix over time or that was not present in the sampled top surface of the landforms. This is due to armouring processes over time and this phenomenon is likely to recur following further wet seasons. The majority of the waste materials present in the waste rock dumps were subgrade banded iron formations (BIF) and chert, which are generally competent and geochemically inert. Some waste material was known to have an elevated risk of erosion but present in relatively small quantities. The presence of a large number of dolerite dyke swarms indicates appreciable volumes of dolerite were produced as waste from the pits. This material has an elevated risk of being highly erodible/dispersive. Clays and shales are also likely to be present in the dumps and are considered to be less competent material (relative to the BIF/chert). This paper presents the process from upfront materials assessment through detailed design to construction of the rehabilitated waste rock dumps, and post-construction sampling and testing to validate model findings.CITATION:Kemp, A, Taylor, I and Lamoureux, S C, 2017. Design to closure – construction of detailed rehabilitation designed iron ore waste rock dumps based on upfront site specific assessment, in Proceedings Iron Ore 2017, pp 353–358 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

The design of solvent extraction plants has been generally based on the assumption of steady operating conditions in both the settler and the mixer units. However, recent experience in both large and small plants has shown this not to be the case. Mixer transients include start up aqueous locking and partial phase separation in secondary mixers, which both lead to reduced plant capacity or overflow of upstream mixers. Analysis of the hydraulic pressure profiles has generated new design methods to eliminate the effects of the partial or complete phase separation. Changes to the method of specification and selection of primary and secondary mixers have been made to eliminate the onset of partial separation during operation. The observation of settler operation has shown that it is also a dynamic process, even under "steady-state" conditions. Four transient phenomena have been identified that lead to internal circulating flows, poor disengagement of fine secondary haze and erratic and high entrainment levels in the discharges. A, first approximation analysis has shown that there are significant pressure differentials within settlers, and these change along the length and with the phase separation rates. A technique to control the effects of these transients was developed that allows plant performance to be improved beyond "standard" expectations. The design and selection of the settler internals is described. Key words: Solvent extraction, Mixer-settlers, Phase separation, Entrainment, Mixer transients

Jan 1, 2003

By G. Miller

The design of solvent extraction plants has been generally based on the assumption of steady operating conditions in both the settler and the mixers. Recent experience with both large and small plants has shown that this is not the case. Mixer transients include start up aqueous locking and partial phase separation in secondary mixers. Both of these lead to either reduced plant capacity or overflow of upstream mixers. Analysis of the hydraulic pressure profiles has generated new design methods to eliminate the effects of the partial or complete phase separation. Further, changes to the method of specification and selection of both primary and secondary mixers have been made to eliminate the onset of partial separation during operation. Observation of settler operation has shown that it is also a dynamic process, even under ‘steady state’ conditions. Four different transient phenomena have been identified that lead to internal circulating flows, poor disengagement of fine secondary haze, and erratic and high entrainment levels in the discharges. A first approximation analysis has shown that there are significant pressure differentials within settlers and these change along the length and with phase separation rates. A technique to control the effects of these transients has been developed which allows plant performance to be improved beyond ‘standard’ expectations. The design and selection of the settler internals is described.

Jan 1, 2001