Search Documents

By C A. "Hawk" Hanger

"The paper that will be presented is an in-depth study of sequential blasting using standardnon-electric shock tube down hole timing along with surface M.S. connector timing.Included also will be a discussion on the advantages in fragmentation, digability, oredilution' and ground vibration versus the common practice of row by row blasting. Alongwith the written presentation, several visual illustrations will be included. The visuals willrefine the actual direction and predicted movement of the shot involved."

Jan 1, 1993

By Tom Treleaven

This guide presents numerous patterns that provide 8 millisecond separations between initiated charges. The guide is tabulated in seven sections to provide quick reference by number of decks or bunch blasting. The pattern is presented in the section where the highest number of decks works. It should be noted that patterns applicable to multiple deck shootings are also applicable for fewer decks.

Jan 1, 1997

By John Watson, Tom Treleaven

This guide presents nur-nerous patterns that provide 8 millisecond separations between initiated charges. The guide is tabulated in seven sections to provide Quick reference by number of decks or bunch blasting. The pattern IS presented in the section where the highe!$ number of decks works. It should be noted that patterns applicable to multipledackshwtings are alsoapplicsblefor fewer decks.

Jan 1, 1995

By Jae-Ho. Lee

For some electronic applications where a dispersed electrically-conductive particulate-phase is employed, the conductivity of the surface (or near-surface region) of the particles provides for the primary mechanism which determines its electrical conductivity. Particles of a less expensive material, which may have desirable thermal-expansion properties, when coated with silver offer a means of also obtaining desirable electrical properties and at low cost. The research conducted was focused primarily on the development of silver-coated tungsten particles for thick-film polymeric conductors. The ammoniacal electrolyte was formulated from silver-nitrate, glycine inhibitor and formaldehyde reductant. The reduction, and subsequent deposition, of silver occurred selectively on the surface of the tungsten particles. Coated particles were assessed by SEM imaging. The thickness of the silver coating was estimated to be approximately 100nm on the basis of a mass account and the coating being uniform. The electrical conductivity of a silver-coated tungsten-powder pellet was found to be similar to that of a silver-powder pellet, of identical geometry.

Jan 1, 1997

By R. Patrick

As a unique South African organisation, CSIR: Division of Mining Technology (Miningtek) strives to support the mining industry by improving health, safety and productivity through developing, adapting and transferring technology. Considerable effort is currently directed towards the development of potential non-explosive mining methods with the potential to allow continuous mining in narrow reef conditions. Besides improving productivity, continuous mining results in concentrated mining which has a significant impact on reducing infrastructural costs. Impact Ripping and Water Pulse Rock Breaking have been tried on gold mines, whereas Activation, Mini-Disc? cutting and the Plasma Holemaker are currently being tested on platinum mines. The organisation?s many years of experience in novel rockbreaking, together with its world-wide collaborator network, has placed it in a unique position to assist the mining industry and manufacturers in developing and/or adapting existing technologies for application underground. Currently a range of technologies are being investigated, which have reached different stages of maturity. The main technologies under investigation are; - Impact ripper system - Water pulse rock breaking - Activated undercutting rollers - Mini disc cutters - Electric rock breaking

Oct 1, 2001

By R. G. B. Pickering, H. H. Haase

Few innovations in the South African gold mining industry could have a more significant impact on improving profitability than non-explosive methods of mining. The far-reaching benefits of this approach are explained and the progress made through development work funded by the industry is described. Three methods are considered: impact ripping, sloting with abrasive waterjets and diamond saws, and breaking from drilled holes with waterguns and electric pulses. Of these methods, impact ripping is the most advanced and requires only minor refinements before production applications can be initiated. Although this method, based on current performance, is expected to yield considerably increased profits, it is predicted that it could perform several times better than at present with further development. The other methods of rockbreaking also show potential. Waterguns and electric rockbreaking would be attractive in unfractured rock for difficult geological conditions, and for confined areas such as gullies and development ends. Methods based on sloting could be combined with any of the other methods to enhance their effectiveness and thus yield further improvements in profitability; also, they could be used to advantage in specific applications. Al the discussed methods, therefore, deserve to be developed further.

Jan 1, 1991

By R. G. B. Pickering, H. H. Haase

CONTRIBUTION BY D. O'CONNOR Mechanical extraction of rock has been a goal sought after for some decades in the South African gold-mining industry. There are factors distinct from the mode of mechanical extraction that may have considerable influence on its prospects for extensive adoption; the rockburst factor is one of these. REPLY BY H.H. HAASE AND R.G.B PICKERING We agree with Professor O'Connor that, in conventional gold-mining operations, a disproportionate number of seismic events occur in the period immediately following a blast; rockburst activity follows the same pattern, and it has been calculated that, if the rockburst peak were spread evenly across the day, the rockburst exposure of stope workers would nearly double.

Jan 1, 1992

By Natasa Mitevska

In the world, as well as in Republic of Serbia, conventional ore reserves are almost exhausted, so the problem of their shortage is more and more expressed. On the other side, there are many locations with significant reserves of polymetallic ores which present huge potential but cannot be classically processed. Each of these classes of materials has particular mineralogical characteristics which affect their processing. Because of that it is necessary to develop particular technology for each unconventional ore in order to extract valuable elements. The aim of investigation was to define technology for complex processing of the Blagojev Kamen sulfide concentrate by pyrometallurgical procedure in order to valorize valuable non-ferrous and precious metals present, and profit with absolute respect of environmental protection laws. The complex composition of the Blagojev Kamen sulfide concentrate with high content of non-ferrous (15.59% Pb, 9.05% Zn, 2.37% Cu) and precious (697 g/t Au and 744 g/t Ag) metals was the main factor for technological procedure and collector selection. Laboratory investigations are done in four series according to technological scheme: oxidizing roasting, charge preparation (flux addition and agglomeration), smelting under reducing conditions, lead bullion refining, Dore metal refining to final products. It is concluded that precious metals are concentrated in lead bullion (up to 97.95% of gold and 93.37% of silver), which has similar composition to lead bullion produced in lead metallurgy. In this case, simplified technology is used for lead bullion processing because of low content of arsenic, bismuth, etc.

Jan 1, 2006

AT the Non-ferrous Metallurgy session on Wednes-day afternoon, R. M. Roosevelt, vice-president of the Eagle-Picher Lead Co., presided. The paper "Sug-gested Improvements for Smelting Copper in the Rever-beratory Furnace," by G. L. Oldright and F. W. Schroeder, was presented by. Mr. Oldright. It was brought out that lessening of dusting of the charge would increase the life of the arch at present operating temperatures, but will not allow much higher tempera-tures to be used unless dusting can be entirely elim-inated. The best opportunity for improving rever-beratory practice lies in the use of still higher tempera-tures but this requires the development of refractories superior to those now used. There was an interesting discussion of the facts brought out. The paper. on the "Formation and Decomposition of Zinc Ferrite," by

Jan 3, 1928

By R. G. Bowman

Discussions of processes for the manufacture of white lead generally open with the statement that white lead is the oldest chemical pigment known to man. This fact is of more than historical interest; in the light of the present extensive use of white lead, it indicates that the compound possesses characteristics that make it unique among white pigments, and superior to all in its particular field. A greater variety of processes have been proposed for manufacturing white lend than for any other one chemical compound. Only a few of these processes have come into commercial use, however, and a large part of the present production here and abroad is made by the process used in ancient times. The outstanding disadvantages of the old process are that it is slow and laborious, affords no control of the product, and yields at best an impure material lacking in uniformity. Improved processes, sometimes classed all together as "quick processes," have had as their main object the shortening of the time required. Most of them accomplish this and some have yielded a superior product as well, but only two or three are now in use commercially. For centuries the manufacture and mixing of paints have been treated as an art, and the practice has been much influenced by tradition and precedent. There is a reluctance to abandon old materials for this purpose, and as few new uses for white lead have been developed, the adoption of the quick processes has been slow. The electrolytic production of white lead is not new, a large number of processes and forms of apparatus have been proposed and patented within the past 25 years, all directed toward the production of white lead, wholly or in part, by electrolysis. One or two of these processes were tried commercially but proved unsuccessful. Process The Sperry process, used by the Anaconda Lead Products Co., is the invention of Elmer A. Sperry, and was worked out to a commercial basis at the East Chicago plant. It resembles, in a general way, earlier methods, but embodies the features that make it possible to operate

Jan 1, 1926

By G. H. Wigton

The oxidized ores of the Chief Consolidated Mining Co., in the Tintic mining district, have never yielded to metallurgical treatment by any standard method except smelting. These ores occur in comparatively small, irregular, siliceous replacements in limestone, and carry silver, lead, and gold as the principal valuable metals. But smelting methods are unsatisfactory, as the lead smelters heavily penalize the largc amount of silica in the ore, and the copper smelters do not pay for the lead in the ore; therefore, an alternative treatment method was sought. In 1916, a metallurgical research department was organized under the direction of the writer. Many standard metallurgical methods were investigated but, on oxidized ore, none yielded extraction great enough to make its use feasible. During some chloridizing-roasting experiments in 1916, made in an assay muffle, the writer noted that large proportions of the silver, lead, and gold were volatilized from certain oxidized ores. The possibility of volatilizing the metals and collecting them in the form of a concentrated fume was then studied. But, as it was shown that satisfactory chloride-volatilization would be limited to a furnace feed with a high fusing temperature of the non-volatilizable constituents, and as the results obtained in a rotary kiln with the admixture of common salt with the ground ore were inferior to muffle tests, further volatilization experiments were discontinued until 1920. During this internal, an expcrimental sulfidizing and flotation plant was operated. After the cessation of attempts to float the oxidized minerals, chloride-volatilization experiments .were resumed. The highly infusible flotation tailing from the operation of the flotation mill was used for furnace feed. The first tests made on flotation tailing mixed with 10 per cent, common salt showed nearly complete lead and gold volatilization but considerably less volatilization of silver than in muffle tests. In attempts to increase the silver extraction, the percentage salt in the furnace feed was varied, and it soon became apparent that the use of smaller percentages of salt raised the fusion temperature of the furnace charge and thus

Jan 1, 1926

By J. J. Mulligan, F. F. Colcord, E. F. Kern

The electrolytic separation of silver and gold has been practiced by the refineries in the United States for a good many years, and probably because of frequent visiting between officials of plants and the consequent exchange of views, operations in the various silver and gold refineries are very similar. We find, for instance, they practically all use electrolytes of approximately the same composition, which, no doubt, is more the result of experience than of studies of electrolytes. At the new electrolytic parting plant of the U. S. S. Lead Refinery, Inc., East Chicago, Ind., considerable attention has been given to the composition of electrolytes, especially to their conductivity and their effect on the character of the silver deposit. We are not aware that anything has been recently published on this subject and are, therefore, presenting such data as we have with the idea that, although it will not be wholly new, it may stimulate interest in the subject. Effect of Copper Content on Conductivity The first work was to determine the specific conductivity of silver nitrate and copper nitrate solutions. Concentrated solutions of silver nitrate and copper nitrate were prepared by dissolving analyzed chemically-pure salts in distilled water, and determining the silver and copper in each. Definite amounts of the concentrated solutions were taken, mixed and diluted to a definite volume. The silver and the copper were determined in each of these solutions and the conductivity was then determined. The plotted results are shown in Figs. 1 and 2. The effect of increasing quantities of silver and copper is readily seen. A comparison of the two sets of curves shows conclusively the benefit of holding the copper content of the electrolyte above 5C g. per liter, as its effect is to increase greatly the conductivity in an approximate propor-

Jan 1, 1926

By Horace Tharp Mann

Jan 1, 1926

By M. H. Merriss

In the last few years, there have been developed at the plant of the Nichols Copper Co., Laurel Hill, 'Borough of Queens, New York City, improvements in electrolytic copper refining by the series system that have materially increased the flexibility and economy of that system. The purpose of this paper is to discuss, as of interest to refiners and to those who have copper to refine, as well as to the engineering profession in general, the changes' that have taken place resulting in wider application and increased efficiency of the series system. Copper is electrolytically refined in two ways, which are spoken of as the "multiple system" and the "series system." In both systems, the electrolytic tanks are in series electrically. In the multiple system the electrodes in a single tank are in multiple or in parallel, thus: There are two important adaptations of the series process, one represented by the series electrolytic tank room at the Baltimore Copper, Smelting & Rolling Co., Baltimore, Md., and the other by that of the Nichols Copper Co.'s plant. At Baltimore, the anode is rolled to perfect

Jan 1, 1926

By G. D. Van Arsdale

This paper describes a series of experiments leading to the development of a method for leaching the mixed ores of the Inspiration Consolidated Copper Co., containing chalcocite and silicates of copper, by the use of solutions acidified with sulfuric acid and carrying ferric sulfate. Iron is added to the solutions and ferric iron is regenerated electrolytically to a percentage high enough to act as an effcient solvent. The decreased yield is partly compensated for by a higher current density. An important problem in modern copper metallurgy, particularly in the Southwest, has been to obtain good recoveries from what are commonly known as mixed ores; that is ores in which the copper occurs partly as oxide and partly as sulfide compounds. The dividing line between mixed ores and ores commonly accepted as concentrating is not definite. In other words, much ore now being concentrated carries considerable copper in non-sulfide form, on which recoveries are not so good as on ores carrying less of these constituents. While treatment by concentration may be commercially profitable on ores carrying oxide copper within certain limits, there are large deposits for which the application of concentration could not be considered, and yet which have not been considered amenable to leaching because they carried too much sulfide. The Inspiration Consolidated Copper Co. has large amounts of such mixed ores, and this paper is an account of the experimental work by which a method was developed for their treatment, and for which a large plant is now being erected by the Inspiration Co. It is not claimed that the method is a general solution of the problem of mixed-ore treatment but it is apparently well adapted for leaching the ores of the Inspiration Co., for which it was designed. The work done has covered preliminary laboratory and test-plant investigation, and a pilot-plant run, extending from March to the middle of December, 1923. Thoroughly consistent and satisfactory results were obtained continuously for more than six months in the pilot plant; and it is believed that the results and probable costs that can be had on a large scale have been definitely proved. The method, however, was designed for local conditions; and while the basic principles are general, there are ores on which it will not work and other ores for which considerable modification may be required.

Jan 1, 1926

By N. H. Jensen, B. L. Sackett, Carlos Bardwell, Simon Jacobson

Lead smelting has been an important industry in Utah for many years. The first lead smelting was done, over 60 years ago, at the Rollins mine in Beaver County, by burning heaps consisting of alternate layers of wood and high-grade carbonate ore. The lead thus obtained was molded into bullets. With the development of the mines, the problem of cheaper handling of the ore became important. The only outlet for this ore was Swansea or the Atlantic Coast but to ship to either cost $150 per ton or more for treatment and handling. From 1864 to 1871, experimenting was done with blast, Scotch hearth, and reverberatory furnaces, with the blast furnace surviving as the standard plant. The first crude furnaces were circular or hexagonal in shape, and were made of adobe and stone, which quickly burned out. They were small, about 21/2 ft. in diameter, and smelted from 3 to 10 tons in 24 hr. The metal had to be tapped from the bottom of the crucible, necessitating a shut down of the furnace during this process. This procedure caused salamanders to form around the tap hole when the furnace was started again, which frequently resulted in freezing. The campaign lasted until a tap of bullion was made. The first successful plant of the crude stone type was operated in 1870. From 1870 to 1872, there was a smelter building craze in the state. During that period, about 20 furnaces were built, chiefly near the mines, and their operation was limited and sporadic. The work was then placed in the hands of trained metallurgists, who standardized on the rectangular form of furnace. In 1871, Daggett, at the Winnamuck mine in Bingham, installed water-jackets around the smelting zone of the furnaces. These furnaces were circular; the diameter at the tuyere line was 3 ft. 6 in. and at the charge floor 5 ft. 3 in. The height from tuyere line to charge floor was 14 ft., height of tuyere line above top of crucible was 3 ft. 8 in. Furnace capacity was about 14 tons per day, with a campaign of about 16 days. Cost of smelting was about $44 per ton. The ores making the

Jan 1, 1926

By G. L. Oldright, F. S. Wartman, H. E. Keyes

The economic manufacture of sulfuric acid by the ordinary chamber process usually involves production on a large scale and a plant that is costly to construct. The nature of sulfuric acid makes it costly to transport any great distance. For these reasons, the metallurgist has not found it feasible, at times, to beneficiate ores amenable to leaching, and a need exists for a local process that will produce acid cheaply on a small or large scale. To leach ores containing residual sulfides, an oxidizer, such as ferric sulfate, is needed in solution. Precipitation with scrap iron is one of the cheapest methods of removing some metals from solution, giving a plant of low first cost and supplying a source of cheap ferrous sulfate. The other ingredient needed for the process is SO2 roaster gas, the addition of which, as described below, will give both ferric sulfate and sulfuric acid. Where roaster gas is a waste or obnoxious product, the expense for materials is still further lessened. The use of ferric sulfate and sulfuric acid as a solvent lends itself well to the utilization of scrap iron as a precipitant, and the stages of the process fit in well together as an economic whole. Applications The hydrometallurgist usually thinks of ferric sulfate as a partial solvent for some of the sulfides of copper alone, as most work has been done on this metal. The processes of Hannay and Christensen, for leaching unroasted galena with ferric chloride made by anodic oxidation, show the added solvent action given by "ic" salts when added to brine solutions. It was found by R. D. Bradford (in some work to be published soon by the University of Utah) that, by the addition of a ferric salt to a brine solution, the silver as well as the lead in an unroasted semi-oxidized ore could be largely dissolved. The "ic" salt in the case of silver has evidently the same effect as the case of cupric sulfate when

Jan 1, 1926

By Arvid E. Anderson, Frank K. Cameron

The weathering of copper-bearing ores with the formation of a water soluble salt and the recovery of the metal by leaching and evaporation precipitation, are processes long known, which have at various times been utilized with more or less commercial success. It is commonly assumed that the technical principles involved are quite simple and their application to a particular case easy. If these assumptions were true, we should anticipate a long list of uniformly successful leaching operations, which is not the case, and one would be justified only in calling attention to either unique or peculiar features of any particular enterprise; whereas, in studying the problems of the recovery of copper from the old workings of the Ohio Copper Co. in the light of available descriptions of other leaching projects, we have not found the assistance hoped for to guide us to the best realization of our own opportunities. It appears desirable, therefore, to call attention to these guiding principles, together with a description of the facts of accomplishment. Justification lies in the fact that the leaching and precipitation of copper at the Ohio Copper Co. mine in Bingham Canyon, Utah, is successful. This success is measured by an average monthly production of 600,000 Ib. of copper at an average operating cost, to date, of 3.85 cents per pound at the company's workings, or 6.32 cents per pound after paying shipping and smelter charges on the finished copper. A total of 17,076,099 Ib. of copper had been shipped to the smelter from the beginning of operations, August, 1922, to April 1, 1925. Probably these results can be bettered with further study and realization of the factors involved and the devising of methods of meeting them. It is now an assured fact that the enterprise will have a relatively long and continuously profitable life and that its reserves will not, nor cannot, be suddenly and permanently depleted. It is particularly noteworthy that the financing of this enterprise has been entirely from its earnings. The few hundred dollars necessary for the first experiments and production were obtained by the sale of used, and no longer needed, equipment from a mill belonging to the company; and all funds since required throughout the growth and development of the enterprise, from a few troughs with a production of 2000

Jan 1, 1926

By Francis C. Krauskopf, Carl E. Swartz

Metallurgists differ considerably in their opinions regarding the effect, if any, of small amounts of iron pyrites, or other iron compounds on zinc sulfide ores during the roasting operation. As a result, the literature on this subject expresses many conflicting ideas. The ore, previously crushed to pass through a 1-mm. screen, dries in the roasting kiln, losing water up to 200° to 300° C. At 150° C. iron pyrites begin to lose sulfur. As the temperature increases, while the ore is passing to the hotter part of the furnace, the sulfur burns to sulfur dioxide, leaving the metals as zinc oxide and ferric oxide. These two substances then interact to form zinc ferrite, a compound, yellow brown in color, having the general characteristics of a spinel. Like magnetite, another spinel, zinc ferrite is insoluble in alkalis and dilute acids. As a result, when leached with 10 per cent. sulfuric acid solution, zinc values tied up in this compound remain behind History In the electrolytic recovery of zinc from its ores, the roasted ores are usually leached with a 10 per cent. sulfuric acid solution. When the zinc ore contains iron pyrites as an impurity in an appreciable amount, the actual yield of metallic zinc is much lower than a theoretical calculation would indicate. Further, losses of zinc are, in a rough way, directly proportional to the amount of iron pyrites or other iron compounds present. When the iron is present in the ore in an isomorphous relation to the zinc, as in the case of a marmatite, a greater amount of zinc remains insoluble than when present as a true pyrite or marcasite. Work on the insoluble residues obtained from leaching of the calcines shows that the zinc lost is intimately tied up in this residue. Some investigators have suggested a definite compound, such as zinc ferrite; others merely a mixture of zinc and iron compounds. As early as 1851, Pelouze(')' prepared calcium ferrite by fusion of calcium oxide and ferric oxide. Ebelman, 2) about the same time, prepared

Jan 1, 1928

By A. S. Dwight

Taking up first the lead field, flotation concentrates offer serious difficulties in handling and in preparing for the blast furnace, quite aside from the problems presented to the furnaceman by the necessity of smelting smaller tonnages of material higher in grade and usually basic in character, with the consequent changes in flux requirements and furnace operation. As received at the smelter, these concentrates are always wet and usually of the consistency of sticky mud. Difficult enough to handle in warm weather, they are worse in winter, when it may be necessary to blast them out of the cars. They hang up in bins and chutes and stick to conveyors, requiring the constant attention of the operators. If dried they become like wheat flour, involving heavy dust losses in handling and in furnace operations. Roasting in hearth furnaces is more difficult than with coarser materials. Dust losses are increased and, what is more serious, the moist concentrates tend to form balls or nodules, which harden and pass almost unaltered through the furnace with consequent high sulfur in the product, while the unballed fine particles lie on the hearth in a dense bed, practically impenetrable to the oxidizing gases, so that roasting takes place only on the surface of the bed. A more prolonged roasting period is therefore required and the capacity of a given furnace is decreased. They are entirely too fine to be charged into the blast furnace, even if thoroughly roasted; excessive flue-dust losses, irregular operation and slowing up of the furnace would be the obvious result. Consequently, it was early recognized that flotation concentrates would have to be put in coarser condition for smelting and the universal method adopted has been the Dwight & Lloyd process of sintering. This did not usually

Jan 1, 1928