Search Documents

By D. Carr, C. Anderson, M. Deal, C. Larson

"Construction of the OceanaGold Haile operation’s process plant in Kershaw, South Carolina is currently under way, with ore through the mill expected in late 2016 and commercial production expected in early 2017. The process is designed to treat 6,350 tonnes per day with minor upgrades required to achieve 8,270 tonnes per day. Plant optimization during detailed engineering, combined with a focus on de-risking the process, has resulted in numerous process changes since the initial design. This paper describes the plant optimization and de-risking, it also presents a proven commissioning strategy modelled after OceanaGold’s Didipio operation, whilst identifying potential expansion opportunities. INTRODUCTION Haile Gold Mine is located in Kershaw, South Carolina, approximately 50 miles south of Charlotte, North Carolina. Gold was first discovered at the site in 1827, and the property has been through several operating periods since. The last operation employed heap leaching from 1985 through 1992. Since then, the property has been closed and fully reclaimed. Romarco Minerals acquired the property in 2007, and began an exploration program that delineated 2.02Moz. of gold in reserve at an overall grade of 2.06 g/t. OceanaGold acquired Romarco Minerals and the Haile Operation in October of 2015. OceanaGold operates under a risk management philosophy in all aspects of operation, both corporately and at each individual business unit, and has implemented numerous process changes to eliminate or mitigate risks identified in the initial design of the processing circuit, and provided increased opportunity for optimization and expansion. This paper describes the plant optimization and de-risking, it also presents a proven commissioning strategy modelled after OceanaGold’s Didipio Operation, and identifies potential expansion opportunities. INITIAL PROCESSING CIRCUIT DESIGN An extensive metallurgical test work program was undertaken by Romarco Minerals and third party laboratories during the initial design phase of the Haile project [1]. This preliminary test work provided the technical information as a basis of plant design. The initial flow sheet for the Haile processing circuit is shown in Figure 1 (see APPENDIX). The plant is designed to process 6,350 tpd (7,000 stpd) on an annualized basis. The process begins with a jaw crusher followed by a SAG and ball mill grinding circuit to reduce particle size to P80 74 µm. A flash flotation cell treats 50% of the cyclone underflow in the ball mill circuit. Grinding circuit product is sent to a rougher flotation circuit to recover gold-bearing pyrite. The flotation concentrates from flash and rougher flotation are reground to P80 13 µm using stirred media detritors (SMD’s). The rougher flotation tail is pumped to the carbon-in-leach (CIL) circuit for gold recovery. The reground concentrate is pre-aerated prior to being pumped to the CIL circuit. The CIL circuit is a hybrid circuit with eight tanks. Tank 1 leaches the pre-aerated concentrate only, and tanks 2 through 8 leach the combined flotation tailing and tank 1 discharge. The carbon strip circuit is a standard pressure Zadra system, followed by electrowinning, and refining using an induction furnace. CIL tailing passes through a cyanide recovery thickener prior cyanide destruction and then pumped to the tailing storage facility (TSF)."

Jan 1, 2017

There is a lack of information concerning the movements of water on the continental shelf, particularly with regard to data obtained regularly over significant periods of time. The Horace Lamb Centre for Oceanographic Research has recently deployed data acquisition systems on the sea bed off the coast of South Australia to record tides, swell, and ocean temperatures. Some of these early records are described. The swell data are pertinent to future offshore operations with drilling rigs, barges, and other equipment, while the temperature variations give evidence of significant bottom currents, apart from those due to swell.

Jan 1, 1971

By Nilsson C

Man has always been and will always be part of his environment, in ,a good, bad or indifferent manner. Until quite recently, this environment has been the atmospheric boundary layer above the land masses, and to a limited extent the air-sea interface of the oceans. Since the days when he lived in caves, he has built up a wealth of observations on these two environments,-with ever-increasing scientific precision which unfortunately until quite recently was completely insufficient for modern capabilities of data analysis. Consequently, in a sense, he has left in his wake thousands of years of missed, opportunities for making exact observations and increasing his understanding. The data of the past are lost and he has to be satisfied with what he can assemble from now on when his environ- ment, largely as a result of his actions, is exhibiting more and more rapid variations in time; in other words, time series of observations of phenomena are required, the length of which is critical for most purposes of analysis.

Jan 1, 1970

By Hewitt Wilson

A review is given of the nomenclature, sources, imports, statistics, common methods of preparation, and testing of mineral pigments. A description of the Deer Park-Spokane colored-clay district and the laboratory methods of preparation of these colored clays, others, and siennas follows. The mineral pigments were prepared by washing or grinding the original material as received and by calcination of the yellow ocher and brown sienna with and without manganese dioxide to produce red, brown, and black colors. These prepared powders were tested for fineness, oil absorption, and color as compared with well-known brands of commercial pigments. Similar tests were made with several basalt red clays occurring in the neighborhood of Salem, Oreg., and Kalama, Eatonville, and Clay City, Wash. The color particularly was studied, since this property is the most important commercial characteristic of the minerals. PURPOSE OF INVESTIGATION Since the development of the clay industry in the Pacific Northwest, some curiosity and interest have been aroused by the red and yellow clay or ocherouslike material that has often been found associated with the commercial clay deposits. These include the red and yellow "paint pots" near Deer Park and Spokane in eastern Washington, a red clay at Clay City, another close to Eatonville in western Washington, and red basalt earths near Salem, Oreg., and along the Columbia River near Kalama, Wash. Several companies have been organized to produce pigment colors from two of these deposits but have either discontinued or never started operations.

Jan 1, 1929

By S. D. Bearden

Color enhances expression and communication in all physical objects experienced in life. Pigments provide color and in some applications have a specific additional function. Natural iron oxides are widely distributed throughout the world but only a few deposits are sufficiently pure and possess acceptable color and brightness properties to merit their processing into pigment form. Ochre, the common name for goethite ore, is the best and most under used material in the buff colored pigment market. The geological occurrence of ochre in the basal Shady Formation of the Cartersville Mining District (Georgia) is described. Exploration, processing, and product applications of New Riverside Ochre Company, Inc. are discussed. An overview of the worldwide pigment market is presented with emphasis placed upon the North American activity in iron oxide production and application. The purpose of this paper is to increase the awareness of ochre and its potential market in the colored iron oxide pigment industry, encourage research on the origin of ochre deposits, and stimulate interest in new applications of this unique substance.

Feb 27, 2013

By M. Pope

By 1950, packaged oil and gas fired boilers were on the market for capacities up to 30,000 lbs./hr. By 1962, capacities were up to 100,000 lbs./hr. and even higher when separate heat traps (economizers and air preheaters) were attached to the boiler packages. During this period, complete packaged coal fired boilers were developed into the 10-15,000 lbs./hr. range. Oil and gas fired plant designs became very compact, "basementless", and far: less costly than the coal fired plants of any capacity. Coal fired plants remained large and expensive, required field erection of boilers and required basements. With the spectacular strides made in automation, oil and gas plants became far less costly to operate, requiring only the part-time attendance of a single operator. Some advances were made in coal fired plants, but not to the degree attained by the fluid fuel competition.

Jan 1, 1965

By George A. Lamb

Forecasters, in estimating long-term energy requirements and supplies, have predicted a bright outlook for coal. Some predictions have annual coal output reaching 800 million tons by 1980, almost twice the average of the last five years. These projections assume that ultimate consumer energy products will be supplied adequately not only in volume but also by kind and type. The consumer energy schedule shifts continually as it reflects the changing demands for numerous uses. Its appearance, expressed generally in proportions of solids, liquids, gases and electricity, is quite different today from what it was in 1940. It may change even more by 1980. Thus, the shares that coal and the other energy sources will have In total supply will depend upon how well each source can be processed into products that will be accepted by consumers.

Jan 7, 1963

By J. L. Bruce

For a number of years, from an economic standpoint, the ventilation of the Colorado mine of the Davis-Daly Copper Co. has been a difficult problem. The development through the main hoisting shaft was pursued for a number of years and to a depth of about 2500 ft.( 762 m.)before large bodies of good commercial ore were opened up. This lack of early success in exploration restricted expenditures for ventilation, with the result that the present orebodies were opened up at a depth of 2500 ft., and in country rock f relatively high temperature, without adequate means f supplying the development faces and the stopes with cool or fresh air of low humidity and suitable velocity. During the progress of development, two or three connections were made at higher levels with the workings of adjoining operations, but these were of a makeshift and unsatisfactory character and afforded no means for carrying downcast air from the surface, in anything approaching a direct course, to the working faces. During the latter part of 1917, arrangements were made with. the Anaconda Copper Mining Co., whereby, during the year 1918 and the early part f the year 1919, a crosscut was driven eastwards on the 2500-ft. level of the Colorado shaft and connection was made by means f an up-raise of approximately 200 ft. to a crosscut driven westwards from the 2800-ft. level of the Belmont mine, this crosscut at the top of the raise being driven at Davis-Daly expense by the Anaconda Copper Mining Co. This connection, in conjunction with a No. 11 Sirocco fan installed near the Colorado shaft, provided the Colorado mine with a maximum of approximately 30,000 cu. ft. per min. of relatively fresh air, most of which came in a fairly direct route from the downcast Belmont shaft through the No. 11 fan to the 2500-ft. level stopes. After passing through these stopes and the stopes of overlying levels, it passed through the main crosscuts on higher levels back to the Colorado shaft, which provided the upcast for this current of air. The improvement

Jan 9, 1921

The subject of octanes and knock in petrol engines is of general interest, not only to the engineers and chemists in the petroleum and automotive industries, but also to the motorist who wishes to see some light through the haze of propaganda regarding "super" petrols. A mixture of petrol vapour and air will explode when a spark is passed through it if it contains more than one and a half per cent. or less than six per cent. of petrol vapour by volume. In a petrol engine the mixture has to be within the explosive range before it will operate. When the spark is passed it 'ignites the petrol vapour-air mixture which burns with rapid but finite progress of the flame front 'through the unburnt gases in much the same manner that a charge of dynamite is consumed. The turbulence of the gases in the cylinder under normal operating conditions more than doubles the velocity of the flame front and enables the combustion to be completed by the end of the working (expansion) stroke:KNOCKIf the cylinder head 'is poorly designed or is covered with a deposit of carbon, it is possible for "hot spots" to develop, and these can ignite the mixture before the spark is passed. This pre-ignition gives rise to an engine knock but is accompanied by a dull thud rather than the ringing knock associated with the true "knocking" found in a petrol engine and attributed to the detonation of the mixture. Until a few years ago it was thought that this detonation was due to a shock wave produced by the rapid combustion of the mixture, and sufficiently intense to cause ignition of...

Jan 1, 1951

By Robert D. Brown, Robert B. Parsons

"The mining industry may have survived the October 28 federal budget relatively unscathed, but the same certainly cannot be said of the petroleum sector-and many mining men are left wondering if their industry will be the next one to be singled out for special attention, as federal and provincial governments seek additional revenues and pursue nationalistic or provincial policies.Higher taxes, higher prices, a potpourri of ""incentives"", and a -""Canadianization"" policy mark the principal features of the new National Energy Program released by the government along with Finance Minister MacEachen's budget address.This month, Tax Notes examines the federal budget. with appropriate emphasis on the National Energy Program and its possible future implications forthe Canadian resource industries.IntroductionMost of the Canadian mining industry (tar sands miners excepted) heaved a sigh of relief on the evening of October 28, 1980, as Finance Minister MacEachen confounded the prophets in his budget address by not raising personal or corporation taxes and by making only relatively modest changes in the general tax system. Instead, he concentrated on a sweeping new energy policy. Unfortunately for that important sector of Canada's mining industry which is involved in mining the country's vast tar sands reserves, either now or in the future, the National Energy Program that was introduced along with the budget 'has serious implications."

Jan 1, 1981

By Daniel Tao, Jike Qiao, Hao Ren, Feifei Ji, Gonglun Chen

The floatation of niobite was studied using a number of collectors at various dosages and solution pH’s. Octyl diphosphonic acid was found to be an effective collector for niobite flotation with good selectivity. A flotation recovery of 91.2% was obtained with 140 mg/l octyl diphosphonic acid at pH’s less than 5.0. Infrared absorption spectroscopy (IAS) and X-ray photoelectron spectroscopy (XPS) were used to characterize the interactions of niobite with octyl diphosphonic acid. Species distribution diagram of octyl diphosphonic acid and niobium species was used to elucidate the flotation behavior of the mineral with octyl diphosphonic acid. A chemical adsorption mechanism of niobite with octyl diphosphonic acid was proposed. Keywords: octyl diphosphonic acid, electrokinetic measurements, niobite flotation, XPS.

Jan 1, 2005

By Milton Camino Ramos

MARSA forma parte de los yacimientos vetiformes de la franja metalogenética aurífera del Batolito de Pataz, y políticamente se encuentra ubicado en la provincia de Pataz, La Libertad. En este sentido, el presente texto describe los resultados del programa de exploración 2010-2011, donde se dio el descubrimiento del primer cuerpo mineralizado del yacimiento, el cuerpo Esperanza, entre otras ocurrencias. Asimismo, se muestra que los cuerpos mineralizados de la franja metalogenética de Pataz, se formarian en estructuras de primer orden con evidencias de reactivacion, cuyo sistema estructural funciona como entrampamiento y en varias etapas de mineralizacion.

Sep 12, 2011

By Fidel Vera Rosas

La presente investigación señala algunos acontecimientos producidos durante el proceso de mineralización del yacimiento San Cristóbal, Junín a través de mantos, vetas y cuerpos irregulares en la zona. Ademá de estos tres tipos de ocurrencias, se prevee la diseminación del cobre, cuyo estudio aún no está definido.

Nov 20, 1978

By Alberto Benavides

El presente texto señala los aspectos geológicos de la ocurrencia de la plata en el Perú a través de un cuadro donde se muestra las principales producciones peruanas en orden ascendente, así como se analiza la ubicación de estos yacimientos como la importancia de estos en la historia y actualidad. Fuera de estos grupos tenemos: Quiruvilca, Alianza,Yauricocha, Santa Luisa Pachapaqui, Cacachara y San Juan de Lucanas.

Jan 1, 1984

By Walter Ccallo, Dante Soberón

El Batolito de la Cordillera Oriental, comprende una diversidad de rocas intrusivas, las cuales varían composicionalmente desde gabros a granitos alcalinos de la serie calcoalcalina. Durante su emplazamiento han sufrido procesos de fraccionación y contaminación en la corteza, dando como resultado granitos metaluminosos y peraluminosos. Los trabajos realizados por el INGEMMET, han permitido la agrupación de las diferentes rocas en unidades y súper unidades, conllevando a determinar tanto las características petrogenéticas, como las relaciones con las mineralizaciones polimetálicas y de elementos estratégicos para cada unidad.

May 1, 2008

By J. L. Pacheco, J. B. Vilca

El presente estudio [Cu-Fe Skarn occurrences at Portachuelo Fm., Pariatambo facies – Ica, Peru] comprende las ocurrencias de Skarn Cu-Fe localizadas al este de la región Ica, Perú, dentro de un área de minería artesanal. Consiste principalmente en rocas calcáreas de la formación de Portachuelo, evidencia de las secuencias marinas; rocas volcanoclasticas de la formación de Copará, evidencia de eventos de volcanismo, y rocas ígneas del Batolito de la Costa.

May 1, 2008

By Michael G. Nelson

Control of the feed provided to mineral processing facilities is a continuing challenge. Much effort is currently being devoted to overcoming these problems. These projects are usually described under the general headings of Mine-to-Mill Integration or Mine-Mill Optimization. It should be possible to combine the knowledge of ore type, mineralogy, and other characteristics (located in the mine modelling system), with the advanced capabilities of state-of-the-art mill control systems, to achieve an improved level of control in mineral processing, allowing optimization of the mill processes on an almost realtime basis. This is not happening because mill feed it is often treated as a uniform material, when in reality it varies in composition and characteristics. The University of Utah is investigating the use of odor sensors for maintaining traceability in ore production and processing. Odor sensors now used in food processing, environmental monitoring, and other applications can detect the presence of very small amounts (0.1 - 500 ppm) of some molecules. An assortment of such molecules could be used to ?tag? blocks of ore as they are mined, according to their respective characteristics. Then, as the ore came into the mill, an array of ?electronic noses? could be used to assess its characteristics in real time.

May 1, 2004

By P J. Hawke, M F. Flis

The Hamersley Basin of Western Australia holds significant tonnages of detrital iron deposits. Formed by a cyclic weathering and eroding sequence of nominally barren banded iron formation, they may form rich proximal accumulations of iron cemented gravels distal from any obvious hard-rock iron mineralisation. While generally small, they nonetheless represent excellent economic targets as they are near surface and easy to mine. The relatively high density of iron detritals, when compared with their sedimentary hosts, makes the gravity method the primary method of exploring for these blind deposits. Identification of possible trap sites is used as a precursor to gravity surveying, with magnetics used as an ancillary method prior to drilling. Application of the gravity method in this terrain is not straightforward. Detrital trap sites are best developed next to the spectacular cliffs that form the range fronts to the Hamersley Ranges. Precise terrain corrections and use of first vertical derivatives are routinely applied to gravity data in an effort to map every possible gravity high that may reflect the presence of a detrital accumulation. Extensions to Hamersley Iron Pty LimitedÆs BS2D deposit were discovered by the routine application of gravity. This methodology has been used to create a model by which exploration for detrital deposits continue to the present day.

Jan 1, 2002

H. Van F. Furman, Denver, Colo. (communication to the Secretary): There are some statements in Dr. Carpenter's interesting paper which appear to require explanation, if not modification.

Jan 1, 1901

Beverley S. Randolph, Frostburg, Md. (communication to the Secretary): It has always appeared to me that each coalseam has its peculiar character or habit, due to the conditions of its formation, by virtue of which it is either persistent or variable in its section over extended areas. One seam will hold its thickness, chemical character, number and position of partings, beds of slate, etc., over a large area, while another will be found to vary in some of these characteristics every few feet. As the position of the outcrop is an accident of the topography, depending on folding and erosion which have taken place since the bed was formed, no one opening in the outcrop, or, in fact, anywhere else, can supply reliable evidence as to the general character of the seam. To determine the character of an untried seam, a number of sections are necessary from widely separated points, in order to show such variations as may exist. Should material variations be developed, more numerous sections are necessary, in

Jan 1, 1901