Search Documents

By T. W. Camm

Aristotle made the observation that man is a political animal. Engineers often like to think they are above the fray when it comes to organizational politics, but most organizational theorists believe politics is a fundamental dynamic in any group. This paper examines the various ways that people use power within organizations to negotiate the political interactions in the work place.

Feb 27, 2013

By J. R. Cooper

Since man began beneficiating ores, a limited number of factors influenced the type of treatment. The ore itself has always been a factor. The first form of concentration was probably hand sorting, and the grade of concentrate and recovery had to be considered from the start. The cost of labor as a factor in mill design did not attain importance until the period following World War I. Power was one of the cheapest commodities available, and consequently power consumption was ignored. That no longer holds true. The present work does nothing to simplify the work of the metallurgist, or designer. On the contrary it adds another element to the design considerations. And while this report concentrates on power consumption, the mill designer must take the other factors into account as well. This study is based on a compilation of data supplied by a number of Western United States copper operations, as well as information from equipment manufacturers. Although its conclusiones apply to other minerals and geographic areas, the information is more precise, when applied to similar ores. The discussion has been divided into sections covering crushing, grinding, and flotation as these are the principal power consuming functions.

Jan 1, 1977

By P. Somasundaran, C. C. Harris

The power consumption of stirred-media mills was studied using an approach developed from work on stirred reactors. Evaluated were the relationships of factors such as stirring speed and impeller and tank dimensions on the torque required to rotate disc and pin impellers immersed in dense particulate media. Data collected under carious experimental conditions were analyzed. The results were summarized and presented in the form of characteristic plots, general equations and dimensionless group correlations involving power and modified Reynolds numbers. Special attention was directed towards the rheological properties of the media, which was considered a non-Newtonian liquid, and hence the equation of power-law liquids was employed. A procedure for estimating the parameters of effective viscosity and scale-up guidelines (with respect to power consumption) are proposed.

Jan 1, 1996

Power consumption of stirred media mills has been studied by an approach developed from work on stirred reactors. Relationships between torque required to rotate both disc and pin impellers immersed in dense particulate media as a function of speed, impeller and tank dimensions, and other relevant variables are evaluated. Data collected during numerous different experimental conditions are analyzed. The results can be summarized and presented in the form of characteristic plots, general equations and dimensionless group correlations involving power and modified Reynolds numbers. Special attention is directed towards the rheological properties of the media, which is considered as non-Newtonian liquids and hence, the equation of power law liquids is employed. Procedure for estimating parameters of effective viscosity and scale-up guidelines with respect to power consumption are put forward.

Jan 1, 1994

By Lukas Pichler

The market trend of advanced high strength steel (AHSS) with demand for higher strength products is increasing continuously. The inline cooling technologies have established as the most powerful metallurgical tool to achieve these demands. However, the cooling capabilities of existing hot strip mills, plate and Steckel mills are often not adequate to generate high cooling rates and the cooling accuracy required for the production of AHSS. Hence there have been many developments for an intensive, highly flexible accurate homogeneous cooling technology. Considering the wide variety of strip and plate geometry, Primetals Technologies have developed Power Cooling Technology for strip and introduced MULPIC®4 Technology for the plate production. In this paper we shall discuss these enhanced technologies that provide the inline cooling requirement with examples from the recently commissioned machines.

Aug 17, 2017

By G. T. Lineberry

Power requirements for a piece of mobile mining equipment are largely dependent on the set of conditions in which they must operate. These conditions are isolated and key parameters are identified. The effect of operating conditions on power determination is investigated. A simulation technique is developed to predict ranges of power demands for off-highway haul units as an archetype, permitting the analysis of changeable operating conditions. This program uses given data, conditions, and probabilities and ranges to solve for individual components of power, which can then be summed. By adopting such a technique, a systematic and rational determination of power is made possible. The usefulness of this basic approach in the determination of power requirements for other mobile mining equipment is emphasized.

Jan 1, 1983

The development of Mount Isa Mines Limited power supply is traced through the history of the mine operations. As would be expected, growth of the power supply system follows closely the increase in mine output, although it will be seen that total kWh. produced per ton milled shows a considerable reduction in later years when the mine output showed a more rapid rate of increase. That this reduction is not more marked is possibly due to the increased community and Shire Council power usage per head of population.INTRODUCTIONThe geographical position of Mount lsa, far from any large regional power supply Authority, dictated the policy that the Company be responsible for the production and suppiy of all power required for the plant operation. The Company also, in November 1937, accepted responsibility for the supply of a part of the power requirements of the township of Mount Isa. The history of power supply to the Mine may be divided into several phases.1. The supply Of lighting and power during the first plant construction period 1929-1931.2. The construction of the first section of the Mines Power Station, comprising Nos. 1 and 2 turbo alternators and boilers.3. The addition of No. 3 turbo alternator and boiler.4. The addition of No. 4 turbo alternator and boiler.5. The addition of No. 5 boiler.6. The addition of a. 2 turbo blowers for air supply to the Copper Smelter converters; b. 1 turbo blower for air supply to the L.ead Smelter; c. 2 turbo compressors for compressed air supply to the Mine and surface plant.

Jan 1, 1961

By David De Klerk, Maximilian Richter, Thirunavukkarasu Pathmathas, Indresan Govender

We consider the average power dissipation distribution for dense granular flows of an idealised mono-sized charge (5 mm glass beads) in a 300 mm diameter tumbling mill operated in the cascading-to-cataracting Froude regime. By combining the inherent frictional nature of particles within a dense flow regime and noting that tumbling mills are typically characterised by collisional and turbulent stresses, we derive the power dissipation distribution for athermal boundary conditions. The input data to the model (velocity, solids concentration, pressure and flow depth) are obtained directly from non-invasive measurement using a nuclear imaging technique: Positron Emission Particle tracking (PEPT). The power dissipation due shear stresses is shown to be the dominant mode of dissipation in the tumbling mill with up to two orders of magnitude difference between pressure induced dissipation and shear.

Jan 1, 2014

By C. D. Woodward

THE Anaconda Copper Mining Co. purchases 25,000 kw. of electric power for its mining operations at Butte Mont. This power is delivered, over duplicate feeders, in the form of 60-cycle, 2400-volt, three-phase current, to five compressor plants, where most of the energy is used for driving air compressors. At the compressor plants are located the switching apparatus for controlling the 2400-volt power and distributing it to the various mines. At these points, also, there are a number of motor-generator sets for converting the alternating current to 275-volt. direct current for the haulage systems. Pole lines convey the power from the compressor plants to outdoor transformer substations at most of the mines. When it is not economical to distribute the power at the lower voltages in the mines, transformers and motor-generator sets are placed at strategic points .underground. All power is purchased on a maximum-demand basis, therefore there is installed at one of the compressor plants an eight-element totalizing graphic wattmeter. This instrument records simultaneously the value of all power taken at the numerous points of delivery, which not only eliminates the diversity factor but permits load dispatching between compressor and pumping plants, and thus materially reduces the maximum demand from the power system. As most of the mine hoisting is done, by 90-lb. compressed-air winding engines, the air-compressor equipment for the winding engines and mining operations is quite extensive. The standard air compressor has a rating of 7500 cu. ft. per min. of free air, and most of the compressors are directly connected to synchronous motors. The synchronous motors are designed for 80 per cent. leading power factor, thus facilitating power-factor correction of total mine load. Consequently by cooperation with the power company, the voltage of the power received at the compressor plants is constant.

Jan 2, 1922

By B. K. Mishra, A. Datta

Estimating the power draw of a ball mill is of great importance from both operational and control standpoints. There are many factors that affect the power draw, and its prediction is particularly difficult in an operating plant. The important factors that affect power draw are the mill dimensions and operating parameters. Although mill dimensions remain the same for any given mill, the operational factors, such as ball load, mill filling and mill speed, may vary. This makes the modeling effort extremely cumbersome. It is for this reason that an artificial neural network is considered for the development of a black-box-type model to predict power draw. In this work, a total of 48 sets of plant data are used. Using these data, a neural network is built and trained. The trained network is used to predict power that is found to be in good agreement with operating mill power for many situations. In addition, the results of simulations are also com- pared to those obtained from a discrete-element method- based power-draw model.

Jan 1, 2000

The first part describes a model (the C model) based on the motion of the grinding charge. The charge is treated as a continuum, which allows analytical solutions to the equations that are developed. The C model is equally applicable to ball-, semi-autogenous and autogenous mills and contains a description of the power draw of both the cylindrical section and the cone-ends. Differences between the power draw of grate- and overflow-discharge mills are described from consideration of the different shapes and compositions of their charges. A large database of industrial mill data is used to demonstrate the accuracy of the model. Part 2 describes a simpler, empirical model (the E model) whose performance is based on that of the C model. The same database was used to assess the predictive capabilities of the E model. The model was shown to be only slightly less accurate than the C model despite its much simpler structure

Jun 18, 1905

By A. R. MacPherson

The procedure to arrive at an energy efficient autogenous grinding plant is carried out in the following steps: First Step - Determine power requirements to grind a particular ore. This work carried out on small samples ground in a 450 mm diameter Aerofall Hill and the results are checked against a standard Bond Index test. Second Step - A bulk sample from the ore zone is ground in a 1.8 m diameter pilot mill. This work is carried on until the power objectives as indicated from the first step have been realized. Third Step - Correlate the pilot mill data, with the data from the numerous samples ground in the small 450 mm mill and arrive at design criteria for the commercial plant. Ensure commercial mill design will be suitable to obtain similar results as those obtained in the pilot mill.

Jan 1, 1981

By Frederick C. Pearson, Albert Brown, Emil R. Ermert

EARLY in 1946 the Shen-Penn Production Co., a subsidiary of the Philadelphia and Reading Coal and Iron Co., was organized to operate the Shenandoah Stripping, one of the largest open-pit anthracite mines in the world. This mine is located in the Western Middle Field near Shenandoah, Schuylkill County, Pa., and involves the removal of approximately 60,400,000 cu yd of overburden to permit the recovery of 9,200,000 gross tons of rough cleaned coal from an area 8000 ft long and 2700 ft wide, with a maximum depth of 400 ft. Operations began in August 1946, and within the next few years 31,811,000 cu yd of overburden and 2,994,000 gross tons of rough cleaned coal had been removed. During the early days of open-pit mining operations, steam was the primary motive power. However, as the size of the equipment increased, so did the problems of fuel, water, labor, and maintenance. Because of its efficiency and convenience, electric power rapidly replaced steam. Later the modern diesel engine was developed, and today practically all stripping equipment is either electric, diesel-electric, or diesel-powered. In locations where electric power is not readily available or where operations are scattered over a large area, diesel power is favored. At Shenandoah operations are highly concentrated in a relatively small area, and this fact, coupled with the availability of ample electric energy, indicated the selection of electric-powered equipment. Since this was a new company, it was necessary to purchase every item, from the smallest tools to stripping shovels. Although the organization period was hampered by the postwar scarcity of materials, an excellent opportunity was afforded to set up a thoroughly modern plant. This paper will describe the power facilities, with particular emphasis on the more unusual features. The substation is a major item in a power distribution system, and a simple arrangement utilizing high quality equipment is an excellent investment. With this in mind, a 3000-kva unit type substation was selected and installed. This unit is made up of three sections, which are assembled simply by bolting together the various sections and connecting the power leads, see Fig. 1. The transformer proper, rated at 3000 kva, is oil-filled and nitrogen-sealed, having a 66,000-v Delta primary and 4160-v Wye secondary with a grounded neutral and 46-ohm ground resistor. The function of this resistor will be described later. Electrical energy is purchased from a public utility and is delivered to the main substation at 66,000 v over one or the other of two incoming lines. These lines terminate on a high voltage switching section on which high voltage fuses and Thyrite lightning arresters are installed. The outgoing feeder switching unit is made up of the following: 1-An auxiliary compartment consisting of potential and current transformers with necessary terminal blocks for connecting to power company metering equipment. 2-Another auxiliary compartment containing a control transformer, battery, and battery charger for the furnishing of power for tripping and reclosing of power circuit breakers. The assemblies in these auxiliary compartments are mounted on carriages that can be rolled in and out with ease. Potential transformers are readily accessible for inspection and fuse replacement. When withdrawn from the operating position they are completely de-energized and grounded. 3-Two feeder breaker compartments, each with a 1200-amp, 5000-v, solenoid-operated magneblast air circuit breaker, voltmeter, ammeter, overcurrent relays, and a ground relay. These power circuit breakers can be quickly and safely withdrawn or repaired. A built-in isolating mechanism is used for lowering the breaker to a transfer truck for repair or inspection or as a means of disconnecting the breaker from the source of power as an added precaution when working on power lines. Thus inspec-

Jan 1, 1952

By Jean-Luc Beaudoin

"In addition to the actual energy consumed, billing is dependent on the peak load and the power factor. The lower the power factor goes, the higher will be the penalty the consumer pays. The principles of a power factor regulator, the two ways of improving the power factor and methods for calculating the capacitor values required will be described.The rate structure of the utility company is founded on three cornerstones: the energy consumed during a given period of time and two penalties imposed when the power factor is low or the power demand is high. Even though the normal consumption of a customer might be 10 kW, with a peak demand of 20 kW only once a month, the wiring and associated equipment at the input to the customer's plant will have to accommodate this peak demand. The power company has no means of forecasting these demands and cannot therefore provide the additional equipment necessary. So it exacts a penalty, and the customer must take all possible steps to avoid these peak power demands. This can be accomplished by using an automatic peak load regulator which will selectively disconnect the loads which are not essential in the operation of a plant .The principles of such a controller will be described.Principles of power factor regulatorsThe operating principles of a power factor regulator will now be described. It might be asked why the power factor of an electrical installation in a mine, or a factory, should be corrected at all, but there is a simple answer. In addition to the actual energy consumed, the billing is dependent on the peak load and the power factor. The lower the power factor goes, the higher will be the penalty the consumer pays."

Jan 1, 1982

By AIME

Annual production of more than 4,000,000 tons of 0.74 percent copper ore and coincident handling of over 5,000,000 tons of waste at the open-pit mine of Castle Dome Copper Co. near Miami, Ariz. takes a lot of power. Manufacturers have ever co-operated with mining companies in providing the required equipment to suit the problem. Power equipment suppliers have done much to make possible the economic and profitable production of copper from low-grade ores. In the future, as mining operations will necessarily handle even lower-grade ores, the ability of the manufacturer to supply the power and mechanical equipment to produce more metal at a fair and reasonable price will be the good right arm of the miner. About 27,000 tons of concentrate is produced from the 4,000,000 tons of ore.

Jan 1, 1948

By M. M. Williams

ALBERTA has been generously endowed with oil, natural gas, coal and water power, thus giving power producers a wide choice in the type of plant and fuel which can be used. Therefore, with such a variety of energy sources to choose from, why was coal selected as the primary fuel at Calgary Power's Wabamun steam plant? This part of the paper will cover the circumstances that led the Company to decide in favour of coal. The second part, to be presented by C. F. Doerr, will describe how the Wabamun coal mine has been developed to supply the large fuel requirements of the power plant. Before considering the Wabamun plant, we require a general under-standing of? the Company's electric system and load. Power is fed into a 5,100-mile high-voltage transmission grid from eleven hydroelectric plants and from the Wabamun steam electric plant. These plants have a combined generating capacity of 820,000 horse-power. Of this total, the hydro

Jan 1, 1963

By Michael F. Gleason

In 1986, Gold Fields began negotiations with a large Nevada electrical power utility to supply power for its Chimney Creek Mine In northern Nevada. After the long negotiations reached an impass over various costs associated with the power line, a decision was made by Gold Fields to generate its own power. Self-generation is not uncommon overseas, but it is rare for any but very large or very small operations in the United States. Surprisingly, under certain conditions a mine can generate its own power profitably and Gold Fields has found that the associated operating and maintenance problems are minimal. The following report details what factors went into this decision and how it works. Hopefully, it can serve as a guideline for those who may find themselves in a similar position.

Jan 1, 1990

By M. F. Gleason, S. Burns, J. R. Arnold

In 1986, Gold Fields began negotiations with a large Nevada electrical power utility to supply power for its Chimney Creek mine in northern Nevada. After the long negotiations reached an impasse over various costs associated with the power line, a decision was made by Gold Fields to generate its own power. Self-generation is not uncommon overseas, but it is rare for any but very large or very small operations in the United States. Surprisingly, under certain conditions a mine can generate its own power profitably, and Gold Fields has found that the associated operating and maintenance problems are minimal. The following report details what factors went into this decision and how it works. Hopefully, it can serve as a guideline for those who may find themselves in a similar position. History In the spring of 1986, Davy McKee Corp. was contracted by Gold Fields Mining Corp. to provide design engineering and construction management for the chimney Creek Mine. Chimney Creek is located about 50 mi northeast of Winnemucca, NV in a remote part of Humboldt County. The nearest industry using utility power was the Pinson Mine, about 13 mi from the proposed plant site. The existing electric line was not capable of carrying another mine the size of Chimney Creek, which required 29 million kwh per year. There were three options available to Gold Fields for the power supply: 1 )Power could be supplied by the public utility from a coal-fired plant about 30 mi away by constructing a new line to the mine,

Jan 1, 1991

By Xin Zhang, Xu Zhang, Hao Bai, Ning Li

Organic Rankine Cycle (ORC) is an effective technology for low-grade waste heat power generation. In this paper, the thermal-dynamic performance of ORC system, in which low-temperature waste heat (from 40-140oC) is used as heat source, was evaluated with software RefProp8.0. The result indicates that in the range of low temperature, the working fluids like R601, R601a, R600a, R141b, R245fa and R245ca have better thermal performance. Furthermore, pilot-scale experiment using R245fa as working fluid was conducted, which validated the operation of the system for low-grade waste heat recovery. Finally, the economic feasibility of ORC has been analyzed for an ORC system using the waste heat from quenching water of blast furnace slag (80oC). According to the analysis, the project is reasonable in economy because the recovery period of investment is less than 4.2 years and environment-friendly since the CO2 emissions can be reduced by almost 43650.68t annually.

Jan 1, 2016

By Callinan AN

Broken Hill Proprietary Company Limited have recently commissioned a 14 Megawatt power station adjacent to its underground coal mining operation at Appin NSW. The power station is fuelled by methane gas extracted from the coal seams 500 metres below the surface. The methane is compressed and cooled prior to its injection into the combustor of a single shaft gas turbine. The turbine is coupled through a reduction gearbox to an alternator. There is sufficient power generated to cover colliery load, with any excess being exported to Prospect County Council, which is the supply authority for the south western region of Sydney.

Jan 1, 1987