Search Documents

By Paykan Safe

This paper reviews various process off-gas cooling options available for sulfide smelting processes. Advantages and disadvantages of each, system are discussed along with the selection criteria for a reliable and cost effective :system. Various systems are presented to demonstrate typical process parameters for smelter off-gas handling systems and to outline operating difficulties associated with each system:

Jan 1, 1998

By J Mercuri, S Dunford, P Rothman, E Bartsch, J Snyder, D Newton, R Maron, D Cirulis

The purpose of a mineral comminution circuit with a ball mill running in closed-loop with a hydrocyclone classification cluster is to feed the downstream process with the target particle size. Maintaining the optimal particle size in the flotation feed can significantly improve plant cash flow. In particular, reducing the amount of coarse material is often a major challenge. Existing instrumentation to provide particle size measurement is considered standard equipment in most modern concentrator plants. However, availability is often very low, mainly owing to high maintenance requirements of the analyser and associated sampling system.CiDRA Minerals Processing has developed two novel and robust technologies that address this challenge by providing high reliability and very low maintenance systems for on-line measurement of coarse material in the overflow of individual hydrocyclones. The first system is non-invasive and measures pebbles and rocks greater than 6 mm. This paper focuses on the second system, which is a ruggedized wetted sensor design with no moving parts and provides a real-time trend of the desired target grind size parameter, such as percentage above 150 micron.Both systems have simple robust designs and measure in the primary overflow stream of the individual hydrocyclone. Individual hydrocyclone measurement enables identification of poor performing hydrocyclones in addition to providing a representative measurement of the whole hydrocyclone cluster. The systems do not require sampling and associated sample transfer piping circuits that are prone to plugging, thus avoiding high maintenance requirements.The wetted sensor will be described in detail along with its implementation in a robust control scheme in a major copper concentrator in North America. Plant data shows very high availability, achieved with very low maintenance, has enabled improved process control, thereby maintaining throughput and ball mill target power while reducing grind size.CITATION:Cirulis, D, Dunford, S, Snyder, J, Bartsch, E, Rothman, P, Maron, R, Newton, D, O’Keefe, C and Mercuri, J, 2015. Process optimisation using real-time tracking of coarse material in individual cyclone overflow streams, in Proceedings MetPlant 2015, pp 93–109 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By P. K. Parhi

The extraction of nickel has been carried out by the hollow fiber membrane technique using D2EHPA as the mobile carrier from the manganese nodule leach liquor after separation of Cu(II), Zn(II) and Co(II). The experiments were designed according to central composite design (CCD), which is a response surface methodology. The process parameters used for the experimental design were: pH, concentration of D2EHPA in the membrane phase, flow rate and H2SO4 concentration in the strip solution. Based on the analysis of variance, a reduced quadratic model was found to best fit the experimental data. The process parameters were optimized to maximize the nickel flux and the optimized conditions were flow rate: 630 mL/min; pH: 6.37; D2EHPA: 1.15 mol/L (1,150 mol/m3) and H2SO4: 2.39% (430.2 mol/m3), for a maximum nickel flux of 7.08 x 10-5 mol/m2.s, which was in good agreement with the actual Ni flux of 6.99 x 10-5 mol/m2.s.

By David Newton, Christian O’Keefe, Robert Maron, Jerin Russell, Paul Rothman, Dylan Cirulis

"The presence of unwanted coarse material in flotation feed streams negatively impacts both recovery and throughput of concentrator plants. The detection of this coarse material is a long-standing problem in mineral processing that has been poorly addressed by existing instrumentation systems. This problem has been overcome by the development of two new systems that detect in real-time the presence of coarse material in the overflow stream of individual hydrocyclones. They both use sensors mounted to the overflow pipe of the hydrocyclone and provide a robust and maintenance-free system measurement that enables corrective actions through operator intervention or automatic control strategies. One system is non-invasive and detects very coarse material 6mm or greater in size. The other system uses a wetted sensor and detects coarse material down to a lower size limit of approximately 100 um. Both systems have been commercially deployed. The systems will be described in detail. Validation data and typical plant data will be shown"

Jan 1, 2014

By Shenghui Guo, Jian Chen, Hongbo Zhu, Jinhui Peng, Linqing Dai, Qianxu Ye

"Response surface method (RSM) based on mono-factor experiment was applied for the process optimization of sintering of chromite fines by microwave. In RSM analysis, effects of binder addition amount, sintering temperature and holding time on the compression strength and shatter strength of the sinter were examined. Results showed that the optimal values of the above parameters were determined as follows: binder addition amount of 1.90% (in mass), sintering temperature of 1153? and holding time of 16 min. Under the optimized conditions, the compression strength was 11155.8? and shatter strength was 95.6849%. The results show that the process was optimized by response surface methodology is stable and feasible, and provide a new way for sintering of chromite fines.IntroductionChromite ore is the main feedstock for ferrochrome, and ferrochrome can be used as steelmaking additive to produce a variety of great strength, corrosion resistant and oxidation resistant special steel, which can be widely used in the aerospace, automotive, shipbuilding, military departments[1], and it has important strategic significance. At present, among the annual world's mined chromite the number of lump ore continues to diminish with its price rising sharply, while the proportion of ore fines been always increased, and the difference in prices between ore fines and lump ore is growing[2]. Despite the low price of chromite fines, and its rich in resources, it can be only used for ferrochrome smelting after agglomeration. Thus manufacturing blocks by using cheap chromite fines is an effective measure to reduce the cost of ferrochrome production and use the chromite resources[3]."

Jan 1, 2013

By Y. Tanaka, M. Maeda, S. Suzuki, C. Tokoro, T. Kato, K. Muto

Boron (B) co-precipitation was investigated with ettringite to establish a cost efficient method of removing B from acid mine drainage. For 25 mg/L of B solution, most appropriate pH for B removal was pH 11.5. The most appropriate amount of reagent for B removal within Japanese effluent standard (10 mg/L) was B:Al:Ca:SO4 = 1:3:9:4.5, which corresponds to the composition of Ettringite (Al:Ca:SO4 = 2:6:3). The effect of silicate, carbonate and temperature on efficiency of B removal is important as groundwater and hot spring water are often contaminated. When silicate and carbonate are present, more Al and Ca salts are needed for B removal since some aluminum and calcium precipitate with silicate and carbonate as kaolinite and calcium carbonate. These precipitates do not contribute much to B removal. As the temperature raised, the most appropriate pH for B removal decreased. B removal became less efficient as monosulfate precipitated more rapidly as ettringite.

Jan 1, 2015

By Frank Ladwig, Stephen Gos

Tailings and/or wastewater generated from gold extraction plants employing cyanida­ tion must often be treated to remove the cyanides and heavy metals for environmental reasons and/or gold extraction inhibition reasons, due to the presence of heavy metals like copper, which have a detrimen­ tal effect during cyanidation. In recent years, the treatment of effluents contain­ ing cyanides and heavy metals has been widely studied, Among chemical treatment methods, the use of hydrogen peroxide has been universally employed as a viable option. However, in some cases, effluents containing high concentrations of heavy metals and/or solids decompose the hydrogen peroxide, an undesirable side reaction. The addition of stabilizers or other peroxygen compounds together with hydrogen peroxide can, however, considerably reduce the rate of decomposition and thus result in detoxi­ fication costs, which are considerably less than the standard detoxification process using hydrogen peroxide. In some cases, the reaction rate can also be increased, resul­ ting in lower investment costs for new detoxification plants. This paper deals with the results of developmental work performed in the recent past and introduces some new processes with the aim of optimizing reagent consumption and costs.

Jan 1, 1992

By John M. Marek

INTRODUCTION This paper is for the mining manager, generally meaning mine superintendent, chief engineer, and others who have control over the mine operation responsible for feeding the insatiable beast called the mill or processing plant. The author is not from mine management but from the field of technical mine engineering consulting. This fact illustrates the authors gross inadequacy to comment on this subject. On the other hand, the consulting profession allows visits to many mine operations, worldwide, supplying many different commodities. The common complaints and misunderstandings that have been heard worldwide will be shared within the following few paragraphs. In order to discuss optimization, one must first define it. There certainly will be many papers in the following sessions that claim to optimize something, or other, based on a technical definition of cost, efficiency, throughput or some other quantifiable basis. DEFINE OPTIMIZATION Actual optimization of an operation is not as easily achieved as most of us in the technical world would like. Borrowing terminology from the technical world, the boundary conditions and the optimization function are usually not well defined. The problems in many cases do not lend themselves to quantification. Typical management procedures are to establish goals or strategies that set the approach or general boundary conditions to the overall plant. Three simple cases are listed below as possible corporate strategies to optimization of a mine-process plant complex. 1) Maximized discounted cash flow 2) Minimized long term cost of product 3) Maximized resource utilization This list seems simple when presented in the above context, uncluttered by constraints such as market position, capital availability, or environmental limitations. Sometimes the best approach is a prioritized combination of the above items. Typically, the Board or CEO has established these strategic priorities. They may

Jan 1, 1991

By Christoph Miller

About 80 years ago the mining industry saw an advertisement of a machine manufacturer: ?One man ? one machine?, meaning the productivity gain by using a pneumatic rock drill instead of manual tools. Mechanization in mining had started. In the 1950's and 1960's when mechanization progressed the word could be transformed into the meaning of ?one man ? one drill rig?. During the 80's automatic functions were added to the machines. Automation started. In the 90's, the first autonomous machines were seen, transforming the advertisement from the 1920's into ?one man ? multiple machines? operated from a remote control room. Soon, the productivity gain achieved by pure automation will also be flating out meaning that the margin cost of further productivity gain will be inefficiently high. What next? In mining operations there is still a high potential of unused productivity lost by ?trivial? things like organization, logistics and operational management. Changing the focus from mechanization and automation towards optimizing the overall mining process will unleash another big potential for cost cuttings and for enhancing efficiency of production. Optimizing an overall process is a task of much higher total complexity compared to an isolated machine automation focus. And a successful process integration requires the collaboration of machine vendors, infrastructure suppliers, IT services and the mine itself. It requires a number of of important preconditions to be fulfilled: ? Integrated IT systems with seamless interfaces between all components and peripherals involved ? Real time information access in all locations ? Real time overview of all operational aspects A crucial aspect for all of these issues is a seamless communication both above and also under ground and IT interfaces which are easy and price efficient to implement. This paper highlights ways to achieve productivity gains by process optimization. It also discusses needs for industry wide activities in order to enable cost efficient performance of mine process optimization projects.

Oct 1, 2009

By G. X. Du

Improving reaction effectiveness of asbestos tailings and acid is main means to increase the productivity of magnesium hydroxide and amorphous silica and to reduce production costs. In this paper, the process optimization of acid-leaching reaction process of asbestos tailings is reported. Through the orthogonal experiments of four influence factors, such as acid consumption, reaction temperature, reaction time and initial acid concentration in the leaching reaction. The experiment results indicated that the optimal process parameters were as follows: reaction temperature was 95?, reaction time was 1.5h, acid consumption was 218.9g hydrochloric acid(37%) per 100g asbestos tailings and initial acid concentration was about 25%. The influence significance sequence of the four factors was as follows: reaction temperature > reaction time > mass concentration of hydrochloric acid > hydrochloric acid consumption. Under the optimum process conditions, the leaching rate of MgO was 97.3%, total iron 98.15% and Al2O3 57.9%.

Jan 1, 2014

By Hampshire MJ

The tailing retreatment project rated at 10 000 t/day commenced operations in October 1982. The operation consists of dredging, feed preparation, cyanide leaching and carbon-in-pulp (CIP) gold recovery followed by Zadra atmospheric stripping and electrowinning. For the first two years the operation was adversely affected by excessive cyanide consumption and low gold extraction. Investigations demonstrated that the very fine, or slime, fraction of the tailing was the dominant consumer of cyanide and dissolved oxygen. The plant flowsheet was subsequently modified by inclusion of 80 - 100 mm dia. cyclones for slimes separation and a 31 m dia. thickener for water recovery. Treatment of deslimed feed in the CIP plant has reduced sodium cyanide consumption from an average 1.85 kg/t to 1.15 kg/t. The reduced oxygen consumption by the CIP plant feed has resulted in higher dissolved oxygen levels, frequently reaching supersaturation after 4 to 5 h contact time. This has allowed much improved gold extraction from the existing CIP plant capacity. Gold extraction from the mixed pyritic siliceous tailing has improved from an average U prior to desliming to a current 57%. Investigations are continuing on the recovery of gold from the discarded slimes.

Jan 1, 1986

By A. J. Paul

Traditionally, 16"/50 caliber projectile shells have been fabricated from forged steel. The Naval Surface Warfare Center (NAVSWC) has determined that cost savings of approximately 60% (-$4.7M/year) as well as improved shell fragmentation can be achieved by casting these shells from austempered ductile iron. One of the technical concerns arising out of this material substitution is the role of the casting process in controlling the quality of the cast shells. Optimizing the process through proper orientation of the mold, placement of chills, superheat, etc., can minimize shrinkage porosity and, consequently, flaw size. For this purpose, the mold filling and subsequent solidification of the projectiles was simulated using a 3-D, fully transient, coupled fluid flow and heat transfer model based on finite differences. Several casting orientations were investigated and the casting parameters were varied to optimize the process and minimize casting defects. A comprehensive software tool, which was developed using state-of- the-art visualization techniques, has been used to analyze the process of casting. Emphasis is placed on the use of this visualization tool as an aid to the foundry engineer for process optimization.

Jan 1, 1992

By M. S. Prasad, K. J. Reid, M. P. Katsoulis

The State of Minnesota is interested in stimulating the development of clay resources and recently supported a two-year project to collect data on geological, mineralogical, processing, economic and environmental aspects of such potential developments. This paper presents the various process options adopted on bulk samples collected from the Minnesota River Valley area, which is a primary deposit and contains a major silica fraction. A standard test flowsheet involving degritting, dispersion. HGMS and cycloning was developed and for some samples yielded an acceptable filler grade product. Secondary streams containing relatively high grade kaolin but of coarse size were also obtained. Improvement in particle size distribution and in physical properties related to paper product specifications (brightness, viscosity) were obtained by size-reduction processes. Market and economic considerations for kaolin consumption in the upper Midwest are analyzed. Current markets for paper grade kaolin in Minnesota are briefly discussed.

Jan 1, 1992

By M. S. Frasad

The State of Minnesota is interested in stimulating the development of clay resources and recently supported a two year project to collect data on geological, mineralogical, processing, economic and environmental aspects of such potential developments. This paper presents the .various process options adopted on the bulk samples collected from the Minnesota River Valley area which is a primary deposit and contains a major silica fraction. A standard test flowsheet involving degritting, dispersion, HGMS, and cycloning was developed and for some samples yielded an acceptable filler grade product. Secondary streams containing relatively high grade kaolin but of coarse size were also obtained. Improvement in particle size distribution and in physical properties related to paper product specifications (brightness, viscosity) were obtained by size reduction processes. Market and economic considerations for kaolin consumption in the upper Midwest are analyzed. Current markets for paper grade kaolin in Minnesota were briefly discussed.

Jan 1, 1990

By C. W. Chao, M. Melashvili, F. Hilário

The processing of a bulk concentrate containing copper as chalcocite, enargite, bornite and chalcopyrite along with pyrite and precious metals of silver and gold was studied. A leaching study was undertaken to examine the application of the atmospheric acid leaching process to a bulk copper concentrate for copper recovery followed by cyanidation or thiosulfate leaching for gold and silver recovery. The extraction of copper exceeded 90% under some conditions and the recovery of gold and silver reached a maximum of 44 and 45%, respectively. A sample of bulk concentrate was roasted in air to oxidize the sulfides with release of sulfur dioxide followed by acid leaching of the roaster calcine and cyanidation of the acid leach solution. The copper extraction reached over 92% and the gold extraction exceeded 88%. The sulfur dioxide may be captured for acid production. INTRODUCTION The processing of a large primary copper deposit in Indonesia is under investigation. One of the possible routes for processing involves flotation of a bulk copper-gold concentrate followed by treatment by an atmospheric leach/SX-EW process for copper recovery. The atmospheric leach residue would then be leached for recovery of gold and silver. A second route involves roasting of the concentrate followed by acid leaching and SX-EW for copper recovery. The leach residue from the roaster calcine would then be leached for recovery of gold and silver. The roaster off-gases could be used for sulfuric acid manufacture, enabling the production of a valuable by-product. The Cobre Las Cruces (CLC) process (Munoz, Garcia, & Delgado, 2017) was designed to treat a resource of copper discovered close to Seville, Spain. The process was developed by Outotec with MK Gold (original project owner). INMET Mining subsequently purchased the deposit from MK Gold and built the copper processing facility. The CLC process is similar to the Mt. Gordon Copper process; except that OKTOP reactors have been installed instead of a low temperature, low pressure autoclave process. The plant was designed to treat 1.3 mtpa of ore at a grade of 6.2% Cu to produce 72,000 tpa of cathode copper over a 15 year project life. The main gangue mineral at Cobre Las Cruces was pyrite. The Cobre Las Cruces ore is therefore similar to a rougher flotation concentrate containing copper minerals and pyrite. The roasting of a rougher flotation concentrate can be designed to produce hematite, basic copper oxides and sulfur dioxide off gas. The acid leaching of the basic copper oxides may produce soluble copper for SX-EW recovery of copper. The sulfur dioxide off-gas may be used to make sulfuric acid.

Jan 1, 2019

Process Options for Difficult Arid-Region Nickel Laterites In the absence of the discovery of significant nickel sulfide deposits, the future of Australia's nickel industry will increasingly depend on cost effect processes for low-grade nickel laterites. The problems encountered with the West Australian HPAL plants, resulting in three of the four plants being shut down, have caused the industry to revisit atmospheric leaching options, particularly heap leaching. West Australian laterites are characteristically very varied in grade, chemical composition and mineralogy with the result that, thus far, one process does not fit all laterites. In this paper the leaching of an especially refractory ore is compared using column leaching of whole ore and atmospheric leaching and HPAL processing of ground ore. The key characteristic is the resistance of the goethite phase to acid attack with low-to-moderate temperature leaching conditions. The refractory characteristic is attributed to the stabilising influence of chromium and aluminium and possibly manganese substitution in the goethite crystal structure and goethite morphology. A significant three-fold increase in both nickel and cobalt extractions under atmospheric leaching conditions was achieved by the relatively simple modification of bubbling sulfur dioxide into the reaction vessel to create a reducing environment. Recoveries increased from <30 per cent to 90 per cent nickel and 86 per cent cobalt after 10 hours of leaching at 95¦C. An even greater improvement was achieved under ambient conditions by heating the ore to temperatures above 250¦C for 30 minutes. Subsequent leaching at ambient temperature gave an eight-fold increase in both nickel and cobalt recoveries after 14 days bottle rolling. Both methods could be optimised and implemented in such a way as to increase laterite reserves in conjunction with a heap leach operation but may be better suited to vat or closed tank processing.

Sep 13, 2010

By A. Kontopoulos

Refractory sulfide gold ores or concentrates require an oxidation pretreatment step to yield the contained gold amenable to the subsequent leaching step. The process options for oxidation pretreatment can be broadly classified as follows: roasting, high or low pressure oxidation bacterial oxidation, chemical oxidation, each with a number of alternative suboptions. Roasting and high pressure oxidation are being applied on an industrial scale; the stage of development of the other options range from preliminary laboratory to advanced pilot plant- In this paper, the major technical, environmental and economic aspects of the above processes are being discussed. Future industrial trends will also be considered. Particular emphasis will be placed on the treatment of arsenical ores and concentrates, where safe plant operation as well as, handling and disposal of the arsenic containing products and/or effluents 'and residues is of paramount importance.

Jan 1, 1990

By P. A. Laxen, P. J. van Staden

Alternative procedures for the recovery of gold from old sand dumps are discussed, with emphasis on the use of heap leaching. The modification of material to improve its permeability prior to heap leaching is not currently receiving much attention in South Africa. The channeling of solutions through heaps and the high consumption of reagents sometimes ascribed to heap leaching can, as shown by the results described in this paper, be lessened by desliming of the sand prior to heap leaching and the treatment of the resulting slimes fraction by agitation leaching and carbon-in-pulp. This combined procedure results in a higher overal recovery of gold. Alternatively, the sand can be heap-leached as it is after agglomeration with lime and cement, which improves the mixing and neutralization of the material, as well as lessening the probability of channeling.

Jan 1, 1988

By James E. Hoffmann

This paper briefly reviews the conventional technologies employed for the treatment of copper refinery electrolyte bleed. The strength and weaknesses of conventional practice will be reviewed and a number of process options to address the weaknesses of present process technology will be described and evaluated. The effect of process selection upon energy consumption and the environmental aspects of process effluent control will be discussed.

Jan 1, 1997

The treatment of nickel ores and concentrates and the subsequent processing to recover separate products of nickel and cobalt is one of the major interests at present in the mining industry. The increasing demand for nickel, and more recently also cobalt, has led to increased exploration for ore sources. Major discoveries have resulted in Canada and Australia. These deposits, as well as others already known, are presently being developed and the process technology tested and evaluated for applicability to the different mineralogical types - mainly sulphide, arsenide and oxide laterites. Concentrates may be treated by either hydro- or pyrometallurgical processes, while the nickel laterites are best suited to hydrometallurgical processing. However, if hydrometallurgy is used, once the ore or concentrate is leached the resultant solutions are then amenable to similar separation technologies for purification and recovery of high purity nickel and cobalt products. Solvent extraction, together with other separation processes such as precipitation, can produce high purity solutions of nickel and cobalt. The final products of these solutions may be nickel and cobalt cathodes, metal powders precipitates or salts, depending on the final process of electrowinning, hydrogen reduction, precipitation, or crystallisation Respectively.

Jan 1, 1996