Search Documents

By Howard C. Pyle, John E Sherborne

Core analysis is a recent development in the field of petroleum technology. The earliest work on this subject was done in connection with evaluating and planning secondary oil recovery by water-flooding. Present-day analysis of sands of flush fields requires new and independent interpretations of the data provided by cored material. Particular attention is being paid to the development of rapid, routine methods for measuring physical characteristics of sandstone, such as permeability, porosity and grain size, as well as the sand's fluid content. Permeability may be defined as the fluid-passing capacity of a rock. For a sandstone to be permeable it must be possible to pass a measurable quantity of fluid through the material in a finite period of time. The common unit of permeability is the darcy, which may be defined as the rate of viscous flow, in milliliters per second, of a fluid of one centipoise viscosity through a porous medium having a cross section of one square centimeter, under a pressure gradient of one atmosphere (76.0 cm. Hg) per centimeter.' For convenience the subunit millidarcy, or one-thousandth darcy, is often used. Porosity is defined as the fluid-containing capacity of a rock and is usually expressed as a percentage ratio of the total pore volume to the rock or bulk volume. Since measurement of only the effective or communicating pore volume is often made, porosities are distinguished as total or effective.2,3 Net effective porosity is defined as the net pore volume available for oil and gas. Oil and water content of sand is measured and expressed either as the percentage saturation of the total pores or of the bulk rock. The oil content may also be expressed as the percentage saturation of the net effective pores. In connection with water-flooding, methods of core analysis were developed to furnish data that could be used in determining the quantity of recoverable oil14-6 and the probable rates at which various sands or divisions of a sand open to the wells would take water or produce oil. In flush fields, the analytical data are used to predict the productivity of a cored interval. They indicate the presence of oil, gas and water and may

Jan 1, 1939

By Howard C. Pyle, John E. Sherborne

Core analysis is a recent development in the field of petroleum technology. The earliest work on this subject was done in connection with evaluating and planning secondary oil recovery by water-flooding. Present-day analysis of sands of flush fields requires new and independent interpretations of the data provided by cored material. Particular attention is being paid to the development of rapid, routine methods for measuring physical characteristics of sandstone, such as permeability, porosity and grain size, as well as the sand's fluid content. Permeability may be defined as the fluid-passing capacity of a rock. For a sandstone to be permeable it must be possible to pass a measurable quantity of fluid through the material in a finite period of time. The common unit of permeability is the darcy, which may be defined as the rate of viscous flow, in milliliters per second, of a fluid of one centipoise viscosity through a porous medium having a cross section of one square centimeter, under a pressure gradient of one atmosphere (76.0 cm. Hg) per centimeter.' For convenience the subunit millidarcy, or one-thousandth darcy, is often used. Porosity is defined as the fluid-containing capacity of a rock and is usually expressed as a percentage ratio of the total pore volume to the rock or bulk volume. Since measurement of only the effective or communicating pore volume is often made, porosities are distinguished as total or effective.2,3 Net effective porosity is defined as the net pore volume available for oil and gas. Oil and water content of sand is measured and expressed either as the percentage saturation of the total pores or of the bulk rock. The oil content may also be expressed as the percentage saturation of the net effective pores. In connection with water-flooding, methods of core analysis were developed to furnish data that could be used in determining the quantity of recoverable oil14-6 and the probable rates at which various sands or divisions of a sand open to the wells would take water or produce oil. In flush fields, the analytical data are used to predict the productivity of a cored interval. They indicate the presence of oil, gas and water and may

Jan 1, 1939

By James A. Lewis

It is the purpose of this paper to show the importance of sand characteristics, when combined with other physical data, in evaluating production obtained by secondary recovery operations, and to indicate the benefits to be gained from the application of these principles to primary production. Introduction During the past 10 years there has been a growing interest within the industry regarding the movement of fluids through oil reservoirs. A number of research projects have been directed toward the development of the physical laws governing this movement. In the period 1933 to the present, correlations between laboratory analysis of cores, reservoir fluids and well performance have been established and have been applied to successful secondary water-flooding recovery operations; and to the completion, production, reconditioning and evaluation of wells in new fields. The application of these data to water-flooding, either natural or artificial, is comparatively new, but the principlcs involved were set forth in 1880 by John F. Carll,1 who said: The flooding of an oil district is generally viewed as a great calamity, yet it may be questioned whether a larger amount of oil cannot be drawn from the rocks in that way than by any other, for it is certain that all the oil can-not be drawn from the reservoir without admission of something to take its place. If one company owned all of the wells drawing upon a pool, and had accurate records of the depth and characteristics of the oil producing stratum in each well, it is quite possible that some system might be devised by which water could be let down through certain shafts, and thus the rocks be completely voided of oil and left full of water. As it is, however, no systematized plan of action can be adopted. The careless handling of one well. by which water is let down to the oil rock, may spoil several others belonging to different parties. A clashing of interests at once arises and is likely to result in disaster to the whole district. In judging of the probable effects of the intro-duction of water into any particular oil district several things are to be considered. (1st) The time of flooding—whether early in the progress of development, while yet a large percentage of oil remains unexhausted or at a later period after the supply has suffered from long continued depletion. (2nd) The structure of the rock—whether regular and homogeneous throughout, or composed of fine sand inter. bedding connected and irregular layers of gravel, sometimes lying near the top and at others near the bottom. (3rd) The shape of the area being flooded. (4th) The position of the point at which water is admitted. in relation to the location of the surrounding wells still pumping oil. (5th) The height (which governs the pressure) of the column of water obtaining admittance. (6th) The duration of the water supply. Although we may take exception to part of Carll's reasoning, particularly " and thus the rocks be completely voided of oil and left full of water," we must give him credit for pointing out the increased effectiveness of water encroachment in displacing oil from a sand and for his recording six of the present seven considerations necessary for evaluation of production of oil by water

Jan 1, 1942

By James A. Lewis

It is the purpose of this paper to show the importance of sand characteristics, when combined with other physical data, in evaluating production obtained by secondary recovery operations, and to indicate the benefits to be gained from the application of these principles to primary production. Introduction During the past 10 years there has been a growing interest within the industry regarding the movement of fluids through oil reservoirs. A number of research projects have been directed toward the development of the physical laws governing this movement. In the period 1933 to the present, correlations between laboratory analysis of cores, reservoir fluids and well performance have been established and have been applied to successful secondary water-flooding recovery operations; and to the completion, production, reconditioning and evaluation of wells in new fields. The application of these data to water-flooding, either natural or artificial, is comparatively new, but the principlcs involved were set forth in 1880 by John F. Carll,1 who said: The flooding of an oil district is generally viewed as a great calamity, yet it may be questioned whether a larger amount of oil cannot be drawn from the rocks in that way than by any other, for it is certain that all the oil can-not be drawn from the reservoir without admission of something to take its place. If one company owned all of the wells drawing upon a pool, and had accurate records of the depth and characteristics of the oil producing stratum in each well, it is quite possible that some system might be devised by which water could be let down through certain shafts, and thus the rocks be completely voided of oil and left full of water. As it is, however, no systematized plan of action can be adopted. The careless handling of one well. by which water is let down to the oil rock, may spoil several others belonging to different parties. A clashing of interests at once arises and is likely to result in disaster to the whole district. In judging of the probable effects of the intro-duction of water into any particular oil district several things are to be considered. (1st) The time of flooding—whether early in the progress of development, while yet a large percentage of oil remains unexhausted or at a later period after the supply has suffered from long continued depletion. (2nd) The structure of the rock—whether regular and homogeneous throughout, or composed of fine sand inter. bedding connected and irregular layers of gravel, sometimes lying near the top and at others near the bottom. (3rd) The shape of the area being flooded. (4th) The position of the point at which water is admitted. in relation to the location of the surrounding wells still pumping oil. (5th) The height (which governs the pressure) of the column of water obtaining admittance. (6th) The duration of the water supply. Although we may take exception to part of Carll's reasoning, particularly " and thus the rocks be completely voided of oil and left full of water," we must give him credit for pointing out the increased effectiveness of water encroachment in displacing oil from a sand and for his recording six of the present seven considerations necessary for evaluation of production of oil by water

Jan 1, 1942

By Charles H. Fettke

The Bradford field of northwestern Pennsylvania and adjacent portions of New York state has attracted world-wide attention in recent years on account of the remarkable success that has been attained in the application of water-flooding as a means of increasing the extraction of oil from a pool that had almost reached the economic limit by ordinary production methods. It is one of the few large oil fields in which artificially conducted water drives have thus far proved successful, although many attempts have been made to apply them elsewhere. As detailed a knowledge as possible of the character of the producing sand in this field is therefore of considerable interest, not only from a scientific but also from a practical standpoint. Outside the Bradford field, such knowledge should aid operators in determining whether or not their sands are amenable to flooding. In the Bradford field itself flooding operations are not uniformly successful over the approximately 85,000 acres of productive area, due in many instances primarily to variations in sand conditions. A knowledge of just what these variations are would often be a great aid in overcoming the difficulties, or else would save considerable sums of money which might otherwise be wasted in experimenting in areas where the chances of success are very small. Realizing that more precise information in regard to the nature of the reservoir rock was essential to improvements in the methods of oil recovery, the Northwestern Pennsylvania Oil Producers Assn., by private subscription of its members, took a core of the Bradford sand from a well 1/2 mile west of Custer City, Pa., during the spring of 1925. The Forest Oil Co. also took a core of the same sand from a well about 8 miles east of Bradford at that time. The cores were submitted to the United States Geological Survey for study and A. F. Melcherl has published the results of porosity determinations on the Custer City core.

Jan 1, 1929

By Henry Emmett Gross

Two types of decline curves are considered and their applications are discussed. The first is the well-known semilogarithmic decline curve having the rate of production plotted on the logarithmic scale and the time on the horizontal scale. The other curve is the percentage of oil in the fluid versus cumulative production, and it is plotted on Cartesian coordinate paper. These curves are illustrated by carefully and adequately labeled graphs. Where conditions permit application of both types of curves for rationally determining the reserves of a well, both should be applied and the most conservative reserve should be chosen. Formulas are given for determining the economic limits. For a semi-l~~arithmic~decline curve the formula is: A = B X C X D X E X F or B = A/C ? D X E X F A = total monthly operating cost (average of past year), B = economic limit in barrels of oil per day, C = days in an average month = 30.4, D = market price of crude per barrel, E = 1-royalty, F = 1-gross production tax, G = water production in barrels per day at the economic limit, H =per cent oil in fluid at economic limit. The economic limit for a per cent oil in the fluid curve is: H = B/B+G X 100 The semilogarithmic decline curve is treated first. Straight-line extrapolations on semilogarithmic paper follow the compound interest compound discount law, hence the ensuing formulas derived from this law may be used in computing reserves for such extrapolations: [1___1/(1+Y)]

Jan 1, 1939

By Henry Emmett Gross

Two types of decline curves are considered and their applications are discussed. The first is the well-known semilogarithmic decline curve having the rate of production plotted on the logarithmic scale and the time on the horizontal scale. The other curve is the percentage of oil in the fluid versus cumulative production, and it is plotted on Cartesian coordinate paper. These curves are illustrated by carefully and adequately labeled graphs. Where conditions permit application of both types of curves for rationally determining the reserves of a well, both should be applied and the most conservative reserve should be chosen. Formulas are given for determining the economic limits. For a semi-l~~arithmic~decline curve the formula is: A = B X C X D X E X F or B = A/C ? D X E X F A = total monthly operating cost (average of past year), B = economic limit in barrels of oil per day, C = days in an average month = 30.4, D = market price of crude per barrel, E = 1-royalty, F = 1-gross production tax, G = water production in barrels per day at the economic limit, H =per cent oil in fluid at economic limit. The economic limit for a per cent oil in the fluid curve is: H = B/B+G X 100 The semilogarithmic decline curve is treated first. Straight-line extrapolations on semilogarithmic paper follow the compound interest compound discount law, hence the ensuing formulas derived from this law may be used in computing reserves for such extrapolations: [1___1/(1+Y)]

Jan 1, 1939

By Hallan N. Marsh

The subject of this paper is apt to bring to mind wells ranging from 6000 to over 8000 ft. in depth. However, it is uncommon to pump wells at depths greater than about 5000 ft. Fig. 1 shows the number of wells being pumped at various depths by one company in Southern California. A few companies have a very few wells pumping at depths greater than this. This paper will deal with wells between 3000 and 5500 ft. in depth. Most California oils at these depths are between 25" and 35" gravity. The subject is so broad that it will be necessary to omit many interesting phases, and to treat others very briefly. Power, power transmission equipment, power efficiency, counterbalancing, sucker rods, pumps and volumetric efficiency will be discussed. Power As a source of power, the 50/20-hp. electric motor is generally preferred. Input is generally between 10 and 25 hp. Due to the uneven-ness of the load, an input of 20 hp. on the low range is generally about all that these motors will carry without overheating, in spite of their overload capacity. In some cases the capacity of the motor limits the speed

Jan 1, 1929

By W. V. Vietti

Actual field data from several wells are used to illustrate the application of the method of determining the average density of the fluid column in a flowing oil well in the Yates field, Pecos County, Texas. The depths of the wells in the Yates field vary from 900 to 1700 ft., depending on surface elevation and the location of the wells on structure. Production rates over 8000 bbl. per hour have been determined and many wells are capable of producing 2000 bbl. hourly. Gas-oil ratios are usually below 400 cu. ft. per barrel, but a few wells high on structure have produced over 3000 cu. ft. per barrel. Incidentally, tubing wells has cut these high ratios to as low as 400 cu. ft.' By common agreement of the operators all wells making ratios over 400 cu. ft. will be tubed. Daily production of the field is prorated to 110,000 bbl. from an open-flow potential of 5,000,000 bbl. based on hourly open-flow gages.

Jan 1, 1931

By Lynn G. Howell, Alex Frosch

In a previous article1 we have described a technique for measuring the relative intensities of gamma rays from the radioactive elements occurring naturally in geological formations along the walls of a borehole. The apparatus consisted of two Geiger-Müller tubes mounted inside a pressure-tight chamber. Each counter tube was coupled separately to an amplifier and a frequency meter at the surface by means of a multiconductor cable upon which the chamber was suspended. The output currents of the two frequency meters were recorded on a photographic paper as the chamber was moved in the hole. These traces showed remarkable correlation with the geologic formations, as evidenced by comparison with commercial electrical logs.2 Owing to the penetrating power of the gamma rays, logs may be taken in both open and cased boreholes. The apparatus has recently been changed somewhat. One of the counter tubes has been removed and a stage of amplification has been added inside the chamber. This arrangement seems to give a more favorable signal-to-noise ratio and satisfactory logs can be now made in cased holes and also in open holes as previously. Briefly described, the chamber moving in the hole is made of 3½-in. drill pipe and is about 10 ft. long. There is an additional extension about 2 ft. long at the top, inside which cable connections are made. The Geiger-Müller tube is mounted inside the bottom end of the chamber. Above this is the vacuum-tube amplifier with its batteries and transformer. In the top part of the chamber, small 45-volt batteries are mounted, which in part supply the high voltage for the counter tube. Additional voltage is supplied from the surface through the multiconductor cable upon which the chamber is suspended. Also, the output of the transformer in the single-stage amplifier is coupled to another single-stage amplifier at the surface through this cable. The surface amplifier is coupled to the Thyratron-controlled frequency meter, the tank circuit of which consists of a one megohm resistor across which is a bank of condensers varying in

Jan 1, 1940

By Alex Frosch, Lynn G. Howell

In a previous article1 we have described a technique for measuring the relative intensities of gamma rays from the radioactive elements occurring naturally in geological formations along the walls of a borehole. The apparatus consisted of two Geiger-Müller tubes mounted inside a pressure-tight chamber. Each counter tube was coupled separately to an amplifier and a frequency meter at the surface by means of a multiconductor cable upon which the chamber was suspended. The output currents of the two frequency meters were recorded on a photographic paper as the chamber was moved in the hole. These traces showed remarkable correlation with the geologic formations, as evidenced by comparison with commercial electrical logs.2 Owing to the penetrating power of the gamma rays, logs may be taken in both open and cased boreholes. The apparatus has recently been changed somewhat. One of the counter tubes has been removed and a stage of amplification has been added inside the chamber. This arrangement seems to give a more favorable signal-to-noise ratio and satisfactory logs can be now made in cased holes and also in open holes as previously. Briefly described, the chamber moving in the hole is made of 3½-in. drill pipe and is about 10 ft. long. There is an additional extension about 2 ft. long at the top, inside which cable connections are made. The Geiger-Müller tube is mounted inside the bottom end of the chamber. Above this is the vacuum-tube amplifier with its batteries and transformer. In the top part of the chamber, small 45-volt batteries are mounted, which in part supply the high voltage for the counter tube. Additional voltage is supplied from the surface through the multiconductor cable upon which the chamber is suspended. Also, the output of the transformer in the single-stage amplifier is coupled to another single-stage amplifier at the surface through this cable. The surface amplifier is coupled to the Thyratron-controlled frequency meter, the tank circuit of which consists of a one megohm resistor across which is a bank of condensers varying in

Jan 1, 1940

By Dale Nix

DuRing the past year approximately 400 depth pressures have been recorded in the Yates field. Of these, 315 were "shut-in depth pressures," observed for the purpose of adjusting well potentials without making open-flow tests. The "shut-in depth pressures" were distributed one to each well and determined under as nearly uniform conditions as possible. Therefore, there is a scarcity of data applicable to production problems, other than the adjusting of well potentials. A few of the data obtained have been used in an attempt to solve some of the producing problems. These applications, however, merely indicate partial solutions and their review herein is to emphasize the variety of problems to which depth-pressure data can be applied, rather than to present conclusive solutions. Very little had been accomplished in the development of instruments to determine pressures within the well bore, when it was decided to obtain such information in the Yates field. Through the combined efforts of the Yates Engineering Committee and several producing companies, three methods of determining pressures in the well bore were soon developed: (1) the "compressor" method, (2) the "volume chamber" method, (3) the "depth-pressure recorder" method. "Compressor" Method.—A small volume compressor is used to inject gas into the tubing. The rate of injection is low so that the frictional losses will be reduced to a minimum. During the test, the pressures at the top of the tubing and casing are observed on recording pressure gages. .As the compressed gas depresses the fluid in the tubing, the pressure on the casing decreases while the tubing pressure increases. The tubing pressure becomes a maximum when the fluid level reaches the bottom of the tubing; and the casing pressure usually rises quickly as the gas breaks around the bottom of the tubing. The sum of the maximum pressure recorded at the top of the tubing and the pressure exerted by the weight of the compressed gas column is equal to the depth pressure at the bottom of the tubing. The procedure can be reversed;

Jan 1, 1932

By C. P. Walker

Determining the distance to remote objects by observing the time required for sound to traverse the intervening space is an old practice. Attempts have been made to use this method for determining the fluid level in oil wells but as far as the writer is aware it was not found to be practicable, because vibrations in gas in the audible frequency range do not travel as well and as far as low-frequency pressure waves, which are capable of transmitting a greater amount of energy than can be transmitted by audible waves. Wood, in his book "Sound," states that in a given medium the range of sound transmission will vary inversely as the square of the frequency. The fact that the sound from a whistle having a low tone has a much lower attenuation rate than that from a whistle of high pitch is well known. Also, the pressure waves caused by cannon fire often rattle windows at points so distant that no sound of the cannon is heard. In 1932 P. E. Lehr and H. T. Wyatt, of the Shell Oil Co., experimented with the principle of the concussion, or pressure-wave echo, method of determining fluid levels in oil wells. They released compressed gas into the top of the casing, thereby creating a pressure wave, which traveled down the well and back again. Their experiments proved conclusively that, with the proper apparatus for recording the echoes and determining the velocities at which the waves travel, the method could be used successfully for determining fluid levels in oil wells. Wells are often equipped with from one to three tubing catchers and these together with the top of the liner are frequently above the fluid. Each of these obstructions reflects a part of the pressure wave. In such wells there may be, therefore, as many as five pressure-wave reflections. Thus it is obvious that in order to identify the various reflections and to determine therefrom the fluid level in a well it is necessary to obtain a graphic record of these reflections.

Jan 1, 1937

By Charles C. Rodd

Prior to 1938, proration procedure in Kansas required the physical testing of wells in order to set up a basis for allocating production. Subsequently the use of liquid-level data and bottom-hole pressure data was authorized on certain types of wells as a basis for calculating well capacities, thereby permitting wells to be tested at low rates and with small volumes of production. This paper gives some attention to the equipment used for obtaining liquid-level data but in general it is devoted to the theoretical and physical factors involved in well testing by drawdown methods. These tests are divided into two classifications: (I) liquid-level data used directly to calculate capacities, and (2) liquid-level data and liquid-level measuring equipment used in connection with other data to determine bottom-hole pressure. Equations and calculations for both types are shown. Well capacities calculated from fill-up data have not been used generally but offer a simple means of testing some wells. Theoretical factors and calculations for such tests are shown. In the state of Kansas, proration laws required that the "ability of a well to produce" be given consideration in state allocation orders and for many years this was the only factor used in prorating the allowed oil. The "ability of a well to produce", was the quantity of oil that could be obtained from a well in a prescribed period, usually 24 hr. Early in the history of State-regulated proration, Kansas operators realized that, unless some restriction were placed upon equip- ment, the competition between producers to obtain large well "potentials" might result in a race to install the largest pumping equipment. Consequently, restrictions were placed upon the size of tubing and length of pump stroke that could be used in pumping wells during potential tests. Later, restrictions were placed also upon the size of tubing and chokes that could be used in flowing walls. Despite the restriction setup, better pumping equipment was designed and installed, pumps were improved, and various devices were invoked to obtain high rates of production for short periods of time. By 1937 pumping cycles of forty to forty-five 54-in. strokes per minute were not uncommon, and numerous wells had produced at the rate of 3500 bbl. per day for short periods. Such production was far beyond any rate that could be long sustained. Equipment necessary to take "potentials" was several times larger than that needed for normal producing purposes, and repairs and replacements required by the high pumping speeds were excessive. Also, many operators suspected that the high rates of production main tained during '"potential" tests were conducivc to early water encroachment. By 1938 large-scale physical testing of wells in Kansas ended, the use of the bottom-hole pressure gauge had become common, engineers and operators were becoming familiar with the term ''productivity index," and bottom-hole pressure was being used as a factor in allocation in many areas. There were many drawbacks, however, to large-scale use of

Jan 1, 1943

By Charles C. Rodd

Prior to 1938, proration procedure in Kansas required the physical testing of wells in order to set up a basis for allocating production. Subsequently the use of liquid-level data and bottom-hole pressure data was authorized on certain types of wells as a basis for calculating well capacities, thereby permitting wells to be tested at low rates and with small volumes of production. This paper gives some attention to the equipment used for obtaining liquid-level data but in general it is devoted to the theoretical and physical factors involved in well testing by drawdown methods. These tests are divided into two classifications: (I) liquid-level data used directly to calculate capacities, and (2) liquid-level data and liquid-level measuring equipment used in connection with other data to determine bottom-hole pressure. Equations and calculations for both types are shown. Well capacities calculated from fill-up data have not been used generally but offer a simple means of testing some wells. Theoretical factors and calculations for such tests are shown. In the state of Kansas, proration laws required that the "ability of a well to produce" be given consideration in state allocation orders and for many years this was the only factor used in prorating the allowed oil. The "ability of a well to produce", was the quantity of oil that could be obtained from a well in a prescribed period, usually 24 hr. Early in the history of State-regulated proration, Kansas operators realized that, unless some restriction were placed upon equip- ment, the competition between producers to obtain large well "potentials" might result in a race to install the largest pumping equipment. Consequently, restrictions were placed upon the size of tubing and length of pump stroke that could be used in pumping wells during potential tests. Later, restrictions were placed also upon the size of tubing and chokes that could be used in flowing walls. Despite the restriction setup, better pumping equipment was designed and installed, pumps were improved, and various devices were invoked to obtain high rates of production for short periods of time. By 1937 pumping cycles of forty to forty-five 54-in. strokes per minute were not uncommon, and numerous wells had produced at the rate of 3500 bbl. per day for short periods. Such production was far beyond any rate that could be long sustained. Equipment necessary to take "potentials" was several times larger than that needed for normal producing purposes, and repairs and replacements required by the high pumping speeds were excessive. Also, many operators suspected that the high rates of production main tained during '"potential" tests were conducivc to early water encroachment. By 1938 large-scale physical testing of wells in Kansas ended, the use of the bottom-hole pressure gauge had become common, engineers and operators were becoming familiar with the term ''productivity index," and bottom-hole pressure was being used as a factor in allocation in many areas. There were many drawbacks, however, to large-scale use of

Jan 1, 1943

By E. V. Foran

Among the many newer disclosures that have accompanied the petroleum industry's progressively deeper exploratory drilling is the increased frequency with which the operators are encountering reservoirs of which the products at the time of discovery exist wholly or predominantly in the gas phase. The popular term "distillate pool" is most often used within the industry when referring to this type of reservoir, and in this paper the term is used in that sense. These pools have been observed in many different surroundings. In some places the entire reservoir is filled with the wet gas containing its water-white condensible products in the gas phase but apparently with no dark oil or other hydrocarbon liquids in the reservoir. The 8200-ft. horizon in the Big Lake field in West Texas is a good example of this type. At other places the wet, or distillate-bearing, gas may form a large gas cap directly overlying and in contact with an extensive reserve of dark oil. Oklahoma City, Kettleman Hills, the 8500-ft. horizon in the Big Lake field, and many others are examples of this type. There are also many places in which the wet distillate-bearing gas fills nearly the entire reservoir space, while the dark oil occupies only a narrow, bandlike zone, which marks the boundary of the reservoir along its lowest productive contour. The heavier components of these deep pool gases are generally water white in color, a large portion of which are condensible in a conventional oil and gas separator, when operated under pressures of the order of 400 to 800 Ib. per sq. in. Although the water-white products recovered in the separator sometimes have end points of 650" F. and higher on standard Engler distillation, they occur only in the gas phase in the reservoir. It is entirely possible that even some small amounts of dark colored reservoir components may occur in the gas phase when the temperature is 300" F. and pressures exceed 6000 Ib. per sq. in. Close approaches to these conditions have been encountered in the deepest producing wells. The condensible content of the deep reservoir gases of the many pools that have been tested or produced to date shows a wide variation in both condensible content, per 1000 cu. ft. of gas, and physical character.

Jan 1, 1939

By E. V. Foran

Among the many newer disclosures that have accompanied the petroleum industry's progressively deeper exploratory drilling is the increased frequency with which the operators are encountering reservoirs of which the products at the time of discovery exist wholly or predominantly in the gas phase. The popular term "distillate pool" is most often used within the industry when referring to this type of reservoir, and in this paper the term is used in that sense. These pools have been observed in many different surroundings. In some places the entire reservoir is filled with the wet gas containing its water-white condensible products in the gas phase but apparently with no dark oil or other hydrocarbon liquids in the reservoir. The 8200-ft. horizon in the Big Lake field in West Texas is a good example of this type. At other places the wet, or distillate-bearing, gas may form a large gas cap directly overlying and in contact with an extensive reserve of dark oil. Oklahoma City, Kettleman Hills, the 8500-ft. horizon in the Big Lake field, and many others are examples of this type. There are also many places in which the wet distillate-bearing gas fills nearly the entire reservoir space, while the dark oil occupies only a narrow, bandlike zone, which marks the boundary of the reservoir along its lowest productive contour. The heavier components of these deep pool gases are generally water white in color, a large portion of which are condensible in a conventional oil and gas separator, when operated under pressures of the order of 400 to 800 Ib. per sq. in. Although the water-white products recovered in the separator sometimes have end points of 650" F. and higher on standard Engler distillation, they occur only in the gas phase in the reservoir. It is entirely possible that even some small amounts of dark colored reservoir components may occur in the gas phase when the temperature is 300" F. and pressures exceed 6000 Ib. per sq. in. Close approaches to these conditions have been encountered in the deepest producing wells. The condensible content of the deep reservoir gases of the many pools that have been tested or produced to date shows a wide variation in both condensible content, per 1000 cu. ft. of gas, and physical character.

Jan 1, 1939

By Joseph Jensen, F. W. Hertel

Many fields have been zoned by nature with shales and intermediate waters between oil zones. Limitations thus imposed have been the basis on which a field was developed. In contrast thereto, in the Ventura Avenue field, nature proved more generous. Always expecting to find such similar limitations, operators drilled deeper and deeper into the oil zone without finding any distinctive shale bodies other than the Gosnell shale and only one intermediate water, which became the point below which the final water shut-off of each well was made. Thus, on top of the structure, about 3300 it. of oil-bearing zone has been penetrated below this intermediate water—a distance of 4000 ft. below the Gosnell shale. At first it seemed that the greater penetration in the zone, the better the well. The error of this assumption became evident as time passed. Other pressing attendant problems requiring consideration also developed. In the spring of 1929, the Associated Oil Co., still having a large undrilled area, adopted a method for developing this land by dividing the oil formation into zones, so as to drill two classes of wells and to prepare for others, if conditions in the future justified or required such action. Wells now completed are considered as permanent completions in the zone or class for which they are drilled, and are not looked on as a ready means for deepening or accepted as a temptation for deepening to get some flush production quickly. Provision has also been made to avoid future water problems. The most striking demonstration resulting from such work is the fact that the top of the structure is far from being the point at which the largest oil recovery is made. Wells on the flank of the structure invariably produce with lower gas-oil ratios and secure much larger oil production. Zoning of Oil Sands The Gosnell shale separates the upper light 50 gravity oil from the lower 30 gravity oil below. As the light oil zone is of practically no importance at present, it is not being exploited. The development pro-

Jan 1, 1931

By Carl J. Christensen

This paper presents the development of diamond coring of the Weber sand section in the Rangely Field, Colorado. The description and operation of the diamond-coring equipment is included as well as the economics and results obtained by its use. Diamond coring is compared with the other methods used for drilling the Weber sand. Two types of diamond coring are discussed. The first and the one used most extensively is the regular 6 ?x 3¾-in. diamond bit and bottom hole 50-ft barrel. The second type, which has also been used successfully by Stanolind, consists of a 4 13/16 x 2 11/32-in. cutting bit and reverse circulation coring equipment. The first type will be referred to as regular or conventional diamond coring while the latter type will be referred to as reverse circulation diamond coring. Introduction Diamond coring has been used for many years in mines, quarries, surface coring at dam sites, laboratory work, and so on, but, until recently, had never been used very extensively in coring oil sands and other oil-bearing strata. It was demonstrated early in its development that hard forma-tions could be cut rapidly and that core recoveries far exceeded those obtained with conventional hard rock bits and quite often 100 pet recovery was obtained. However, the poorly constructed diamond-coring equipment and resulting high costs of early diamond coring slowed down its progress. Early in the development Of the Rangely Weber field, Rio Blanco County, Colorado, the Rangely Engineering Committee selected key wells that were to core the Weber section in its entirety. These cores were to be analyzed and various sections tested to gather sufficient information so that accurate reservoir studies could be made. The number of wells selected were kept at a minimum inasmuch as the productive Weber section, which is found at an approximate depth of 6000 ft, is thick, being as much as 600 to 700 ft on top of the structure. The Weber section is also comparatively hard to drill. For instance, one well took 60 days to core 490 ft of Weber sand with conventional coring equipment. It was noticed, however, that Core Labora-verse diamond plug cutter could quickly cut a plug from. one of these hard cores. This fact led to the serious consideration of diamond coring the Weber sand. The first diamond coring at Randy was performed by Stanolind in August 1946 andl although we experienced some difficulties, the results definitely indicated that diamond coring would be successful at Rangely for .coring the Weber sand. As more wells were cored and the equipment improved somewhat, diamond coring became less expensive than drilling the Weber sand with the conventional rock bit. In less than one Year diamond coring has definitely Proved its usefulness in oil-field drilling operations in the Rocky Mountain area where formations quite often drill very hard. The practice of spot coring in hard oil-bearing formations with conventional coring equipment is giving way diaimond coring of the entire sections, thus givng an operator the complete picture.

Jan 1, 1948

By Carl J. Christensen

This paper presents the development of diamond coring of the Weber sand section in the Rangely Field, Colorado. The description and operation of the diamond-coring equipment is included as well as the economics and results obtained by its use. Diamond coring is compared with the other methods used for drilling the Weber sand. Two types of diamond coring are discussed. The first and the one used most extensively is the regular 6 ?x 3¾-in. diamond bit and bottom hole 50-ft barrel. The second type, which has also been used successfully by Stanolind, consists of a 4 13/16 x 2 11/32-in. cutting bit and reverse circulation coring equipment. The first type will be referred to as regular or conventional diamond coring while the latter type will be referred to as reverse circulation diamond coring. Introduction Diamond coring has been used for many years in mines, quarries, surface coring at dam sites, laboratory work, and so on, but, until recently, had never been used very extensively in coring oil sands and other oil-bearing strata. It was demonstrated early in its development that hard forma-tions could be cut rapidly and that core recoveries far exceeded those obtained with conventional hard rock bits and quite often 100 pet recovery was obtained. However, the poorly constructed diamond-coring equipment and resulting high costs of early diamond coring slowed down its progress. Early in the development Of the Rangely Weber field, Rio Blanco County, Colorado, the Rangely Engineering Committee selected key wells that were to core the Weber section in its entirety. These cores were to be analyzed and various sections tested to gather sufficient information so that accurate reservoir studies could be made. The number of wells selected were kept at a minimum inasmuch as the productive Weber section, which is found at an approximate depth of 6000 ft, is thick, being as much as 600 to 700 ft on top of the structure. The Weber section is also comparatively hard to drill. For instance, one well took 60 days to core 490 ft of Weber sand with conventional coring equipment. It was noticed, however, that Core Labora-verse diamond plug cutter could quickly cut a plug from. one of these hard cores. This fact led to the serious consideration of diamond coring the Weber sand. The first diamond coring at Randy was performed by Stanolind in August 1946 andl although we experienced some difficulties, the results definitely indicated that diamond coring would be successful at Rangely for .coring the Weber sand. As more wells were cored and the equipment improved somewhat, diamond coring became less expensive than drilling the Weber sand with the conventional rock bit. In less than one Year diamond coring has definitely Proved its usefulness in oil-field drilling operations in the Rocky Mountain area where formations quite often drill very hard. The practice of spot coring in hard oil-bearing formations with conventional coring equipment is giving way diaimond coring of the entire sections, thus givng an operator the complete picture.

Jan 1, 1948