Search Documents

By Alexander Anderson

In many oil fields a great variation in the production of adjoining wells has long been observed, and a certain proportion of dry holes, situated between prolific producers, has been regarded as normal without thorough investigation as to cause. Similarly, an occasional prolific producer has been found in a part of a field where all other holes have proven disappointing. Adjoining wells which showed an unreasonable difference in production have been surveyed, and the bottom of the poorest producer has been found to have lost sufficient vertical depth, through its drift, to diminish seriously its penetration in the oil zone. Again, the bottom of the good producer has been found to he more favorably situated by its migration up structure. Surveying of wells in California fields has shown many instances where the dry hole has drifted far off the structure to such a degree that no amount of deepening could ever convert it into an oil well. In other cases, edge wells have been found to drift into the field. At this time, in California, the surveying of oil wells is beginning to he accepted as a routine part of operating procedure. Some operators are surveying all of their new wells and, in some of the recently discovered fields, this practice is providing invaluable assistance in methodical development. The information that has been obtained from the surveying of many wells has convinced most operators that it pays to give careful attention to the drilling of wells. Chews are now usually cautioned to avoid reckless competition with each other. Whereas, formerly, certain companies demanded a large footage from their drillers, they now issue orders that a very moderate speed in drilling shall he maintained and that every care be taken to avoid practices likely to cause excessive deviation of the hole frorn vertical. As a result of these new instructions to drilling crews, a distinct decline in the average drift of the wells drilled by these operators has taken place and fewer dry holes are being drilled from good locations. To the petroleum engineer and the geologist, oil-well surveys provide the necessary data required for the construction of the correct cross-

Jan 1, 1929

By Morris Muskat

In preparing a well for pumping, observations are often made of the fluid level in the well bore or bottom-hole pressures at various times before equilibrium has set in. From a qualitative point of view one may immediately infer that if the rise in the bottom-hole pressure or fluid level is rapid the permeability of the sand about the well bore is large, and converse conclusions may be drawn if the rise is slow. However, a more quantitative estimate will give additional information of value, as will be shown in this paper. To derive such an estimate we may proceed as follows. Let h be the fluid height, above the sand face, at time t, and let yo be the average density of the fluid that enters the bore. The bottom-hole pressure, for a fluid height h will therefore be p = rogh, neglecting, of course, the friction drop in the well bore, while the fluid is rising, as may be justifiably done for most pumping wells. If a is the free area of the open-flow string—assumed to be uniform— the rate of production from the sand during the rise of fluid will be: where the last part of the equation merely indicates that, in general, the production rate Q must be considered as a function of the back pressure, and is determined by it alone. In fact, equation 1 shows that if the rate of rise of the pressure or fluid level is determined as a function of the height of rise, or p, for a number of values of the latter, this functional relation between Q and p will be immediately given. Conversely, if we know this functional relation, the rate of increase of p or h may be predicted, or, by observing the rate of rise of p or h some of the constants of the sand may be determined. Thus we may approximate the production from a well in a pumping state by that of a dead

Jan 1, 1937

By W. H. Echols

An oil-emulsion mud, consisting of a mixture of oil-base mud and bentonitic water-base mud, has been used experimentally in drilling 8 of the 35 wells in the Sivells Bend field, Cooke County, Texas. Experience indicates the oil-emulsion mud can be controlled in much the same manner as a water-base mud, and the "drilling" functions of the two types of mud are comparable. The average water-loss for the oil-emulsion mud was 3.8 cu cm per well. When using oil-emulsion mud to drill the last 2000 ft of 7000 ft wells, the mud costs were approximately 2½ times that of water-base mud. There is nothing to indicate well productivities have been affected through the use of oil-emulsion mud. However, drilling time and bit footages were increased and the holes were maintained more closely to bit guage. The apparent advantages gained through the use of oil-emulsion mud in the Sivells Bend field do not appear to justify the increase in mud costs. Introduction until a comparatively few years ago most of the development of drilling mud was directed toward improving the functions of the mud as related to actual drilling operations. The industry has long recognized that one disadvantage of rotary drilling over cable-tool drilling is the possibility of injury to producing zones through the blocking effect resulting from the infiltration of water or mud into the sands. Recognizing this disadvantage, considerable attention has been diverted toward the development of muds that will improve the quality of well com-pletions through the reduction or elimination of water into the sands, but without sacrificing too many of their "drilling" functions and at a cost commensurate with the benefits derived from their use. This phase of mud research has already found practical application, for example, in the development of the Rangely field, Colorado, it appears the use of oil-base mud during drilling-in operations will contribute appreciably toward making this exploitation more profitable. Much of the discussion to follow will be better understood if a brief sketch of the Sivells Bend field is given. The Sivells Bend field, discovered by The Texas Co. in 1944 and still in the process of development, is in a large bend on the Texas side of the Red River about 85 miles north of Dallas. Geologically, the structure is an unsymmetrical anticline, with faulting having contributed to its development. The productive sands are of the Strawn series of Pennsylvanian age, the sands being lenticular in character and varying considerably in development from well to well. At Present there are 35 producing wells in the field, producing from seven different sand lenses. The productive sand lenses vary from 15 to 50 ft in thickness and the individual sands have average permeabilities of from 75 to 375 md. The presently productive sands are encountered at depths of from 6300 to 7300 ft, but testing has indicated that commercial production might be obtained from other sands as high as 5200 ft. Histories of older Strawn

Jan 1, 1948

By W. H. Echols

An oil-emulsion mud, consisting of a mixture of oil-base mud and bentonitic water-base mud, has been used experimentally in drilling 8 of the 35 wells in the Sivells Bend field, Cooke County, Texas. Experience indicates the oil-emulsion mud can be controlled in much the same manner as a water-base mud, and the "drilling" functions of the two types of mud are comparable. The average water-loss for the oil-emulsion mud was 3.8 cu cm per well. When using oil-emulsion mud to drill the last 2000 ft of 7000 ft wells, the mud costs were approximately 2½ times that of water-base mud. There is nothing to indicate well productivities have been affected through the use of oil-emulsion mud. However, drilling time and bit footages were increased and the holes were maintained more closely to bit guage. The apparent advantages gained through the use of oil-emulsion mud in the Sivells Bend field do not appear to justify the increase in mud costs. Introduction until a comparatively few years ago most of the development of drilling mud was directed toward improving the functions of the mud as related to actual drilling operations. The industry has long recognized that one disadvantage of rotary drilling over cable-tool drilling is the possibility of injury to producing zones through the blocking effect resulting from the infiltration of water or mud into the sands. Recognizing this disadvantage, considerable attention has been diverted toward the development of muds that will improve the quality of well com-pletions through the reduction or elimination of water into the sands, but without sacrificing too many of their "drilling" functions and at a cost commensurate with the benefits derived from their use. This phase of mud research has already found practical application, for example, in the development of the Rangely field, Colorado, it appears the use of oil-base mud during drilling-in operations will contribute appreciably toward making this exploitation more profitable. Much of the discussion to follow will be better understood if a brief sketch of the Sivells Bend field is given. The Sivells Bend field, discovered by The Texas Co. in 1944 and still in the process of development, is in a large bend on the Texas side of the Red River about 85 miles north of Dallas. Geologically, the structure is an unsymmetrical anticline, with faulting having contributed to its development. The productive sands are of the Strawn series of Pennsylvanian age, the sands being lenticular in character and varying considerably in development from well to well. At Present there are 35 producing wells in the field, producing from seven different sand lenses. The productive sand lenses vary from 15 to 50 ft in thickness and the individual sands have average permeabilities of from 75 to 375 md. The presently productive sands are encountered at depths of from 6300 to 7300 ft, but testing has indicated that commercial production might be obtained from other sands as high as 5200 ft. Histories of older Strawn

Jan 1, 1948

By E. L. Davis

There have been many attempts to devise formulas for flowing efficiency and flow friction of oil-gas mixtures in oil-well flow tubes. Actually, however, flowing efficiency is rarely any real concern of the oil producer and flow-friction formulas contain so many unknown variables as to be of little, if any value. The production engineer is generally concerned with producing as much oil as possible with a minimum expense per barrel, and with the lowest possible net gas-oil ratio. These ends frequently are opposed to each other and the gas-oil ratio usually is sacrificed. In competitive operations, such as in town-lot fields, high current production is the sole interest. In conservative operation the greatest possible amount of oil obviously should be produced by natural flow unless the net formation gas-oil ratio can be improved by circulating gas. In practice this condition frequently exists. It would be a great advantage if the flowing condition of a well could be analyzed to determine the best possible producing status. Anticipating the death of a well so that gas-lift could be started immediately after the death, or preferably before, would save both production and expense. Frequently it happens that circulating gas fails to help a flowing well, or will not flow it after it has stopped flowing naturally. A knowledge of the laws governing flow would save considerable expense in testing such cases. A predetermination of probable pressures and amounts of circulating gas needed to flow wells and give best possible producing conditions would help in designing compressor installations. The optimum producing status of an oil well generally may be obtained by the conditions that subject the producing formations to the least possible back-pressure. This pressure is made up of the weight of the fluid column, frictional resistance to flow and the reaction from the acceleration of the fluid mass. A mathematical calculation of these components to arrive at a condition giving a minimum summation is impractical. Formulas would be complex and the results untrustworthy because it is impossible to assign proper values to the many variables involved.

Jan 1, 1931

By Joseph Jensen, J. B. Stevens

The history of the normal oil field is supposed to show an oil graph starting high in flush production, descending more or less steeply into the curve of settled production and dropping gradually to the vanishing point of economical operation. Together with this, somewhere in the early history of the field, there appears from a vanishing point a graph showing the production of water. During the period of settled production this graph rises higher and, toward the close, unless extensive work is done in the line of correction, rises far above the oil graph to the point at which the cost of operation terminates profitable pumping. Fields that start out with a high relative content of water are generally very short-lived. Fields that never develop a water problem are exceedingly rare. The McKittrick oil field, Kern County, California, with 840 acres of proved ground, 300 wells and a present recovery per acre of 94,598 bbl. from 1898 to Aug. 1, 1930, presents a study which is an apparent reversal of the outlined normal history. Though the history of the field now covers over 30 years of operation, it is still too early and the conditions too unique to project the graph of production to completion. The present conditions and directions of change are most interesting, in that the curve of oil production is remarkably flat and the curve of water invasion, after reaching an appalling height, has shown a definite reversal and a continued decline for 10 years. Early drilling in the McKittrick field was in or prior to 1898. Development continued steadily to 1918 when the present limitations of the field were determined. Shut-offs, according to accepted practice of the time, were made by driving the shoe into a shale stratum or into a tamped-in bridge of sand, rosin and clay. Records of early days speak of three waters: (1) surface water which was fresh; (2) an intermediate sulfur water, encountered below the top oil or tar sand; (3) bottom salt water. In different portions of the field any one of these waters let into a well by faulty completion might require immediate correction to obtain satisfactory production. In many wells,

Jan 1, 1931

By R. M. Leibrock, C. W. Ziemer, R. P. Vincent

The Stanolind flowmeter, which employs a hot-wire anemometer connected in a Wheat-stone bridge circuit, has proved useful for determining the relative productive ability of individual sand members of gas wells. The operation of this instrument in measuring gas velocities in the well bore above each producing member has provided both a direct and accurate means of analyzing reservoir performance. Results of tests conducted with the well flowmeter in the Hugoton gas field of western Kansas have indicated some rather unusual production characteristics. In two cases it was found that all or the greater part of the total gas produced was coming from one section in wells where four "pay" sections had been perforated individually. These actual measurements contradict in many instances the indications of data obtained from electric logs and from core analysis; the fact that these latter sources often give incorrect results, demonstrates the necessity of a method, such as is provided by the well flowmeter, for accurately determining the amount of gas coming from each producing member. Introduction In any gas well where a number of pay sections have been perforated individually and are producing to a common outlet, the question arises as to the relative amounts of gas being passed through each set of perforations. In the past it has been the policy to depend on core analysis to estimate relative productivities, or, where the sections were not cored, to obtain some idea of production characteristics from electric-log studies. The weaknesses in these methods are readily apparent and indicate the need for more reliable means of measuring gas flow from each zone. The Stano-lind flowmeter* was developed for this purpose. Preliminary tests were made with the instrument in the Katy gas field near Houston; however, the bulk of the routine work with the well flowmeter has been confined to the Hugoton gas field in western Kansas, where results obtained have been encouraging. A description of the instrument, the field technique employed in testing, and a few of the results obtained in the Hugoton area are discussed in this paper. Description or Instrument The well flowmeter is 1¾ in. od and 7 ft long; it is entirely self-contained, can be run through tubing as small as 2 in. id in wells with high pressure (4500 psi) and temperature (210°F) and is lowered on a wire line commonly used for other instruments of the bottom-hole type at falling rates up to 500 ft per minute. It will detect gas flow as low as 10 ft per minute linear velocity, and yet withstand and record velocities of 1000 ft per minute without damage to the detecting element. Killing the well is not required nor desirable for running a production profile when using the instrument, and it is necessary to stop flow for only a short time. The detecting element of the instrument is a hot-wire anemometer connected in a

Jan 1, 1948

By R. M. Leibrock, R. P. Vincent, C. W. Ziemer

The Stanolind flowmeter, which employs a hot-wire anemometer connected in a Wheat-stone bridge circuit, has proved useful for determining the relative productive ability of individual sand members of gas wells. The operation of this instrument in measuring gas velocities in the well bore above each producing member has provided both a direct and accurate means of analyzing reservoir performance. Results of tests conducted with the well flowmeter in the Hugoton gas field of western Kansas have indicated some rather unusual production characteristics. In two cases it was found that all or the greater part of the total gas produced was coming from one section in wells where four "pay" sections had been perforated individually. These actual measurements contradict in many instances the indications of data obtained from electric logs and from core analysis; the fact that these latter sources often give incorrect results, demonstrates the necessity of a method, such as is provided by the well flowmeter, for accurately determining the amount of gas coming from each producing member. Introduction In any gas well where a number of pay sections have been perforated individually and are producing to a common outlet, the question arises as to the relative amounts of gas being passed through each set of perforations. In the past it has been the policy to depend on core analysis to estimate relative productivities, or, where the sections were not cored, to obtain some idea of production characteristics from electric-log studies. The weaknesses in these methods are readily apparent and indicate the need for more reliable means of measuring gas flow from each zone. The Stano-lind flowmeter* was developed for this purpose. Preliminary tests were made with the instrument in the Katy gas field near Houston; however, the bulk of the routine work with the well flowmeter has been confined to the Hugoton gas field in western Kansas, where results obtained have been encouraging. A description of the instrument, the field technique employed in testing, and a few of the results obtained in the Hugoton area are discussed in this paper. Description or Instrument The well flowmeter is 1¾ in. od and 7 ft long; it is entirely self-contained, can be run through tubing as small as 2 in. id in wells with high pressure (4500 psi) and temperature (210°F) and is lowered on a wire line commonly used for other instruments of the bottom-hole type at falling rates up to 500 ft per minute. It will detect gas flow as low as 10 ft per minute linear velocity, and yet withstand and record velocities of 1000 ft per minute without damage to the detecting element. Killing the well is not required nor desirable for running a production profile when using the instrument, and it is necessary to stop flow for only a short time. The detecting element of the instrument is a hot-wire anemometer connected in a

Jan 1, 1948

By R. J. Schilthuis, T. V. Moore

In a previous paper,' the results of some experimental work on the measurement of slippage in the flow of oil and gas mixtures through vertical pipes were presented. The data obtained were correlated and equations were deduced from which the performance of the experimental gas-lift could be predicted with reasonable accuracy. However, attempts to apply the equations to the calculation of pressure drops in actual flowing wells yielded erroneous results. At the time the results of the experimental work were published, no satisfactory explanation could be offered for the failure of the empirical equations to express properly the performance of wells. However, recent work has led to the development of a new hypothesis which presupposes certain conditions affecting the flow of oil and gas in wells. When the proposed equations are corrected to allow for these conditions, an agreement between the observed and calculated performance of the actual wells is obtained which in most cases is quite satisfactory, although it is subject to certain limitations. In this paper, the method of calculating the pressure drop in actual wells is considered, and the application of the method to the design of tubing is discussed. (For nomenclature used in this discussion, see Table 1.) Factors Affecting Slippage and Efficiency At the outset, a few of the principle factors affecting slippage and efficiency in the gas-lift discussed in the previous paper will be reviewed. In the flow of the mixture of oil and gas in a vertical pipe, slippage is the phenomenon of gas moving upward with a. linear velocity greater than that of the oil. Under steady conditions, if given quantities of oil and gas enter the tubing per unit of time, the same quantities of oil and gas per unit time must, on the average, pass every section of the tubing; otherwise, there would be accumulation or depletion of the oil or gas at some sections, and the flow would be unsteady. Therefore, if the gas is to flow at a greater linear velocity than that of the liquid,

Jan 1, 1933

By R. W. Brauchli

The author has made a statistical analysis of the relations between recovery and length of cores, diameters of cores and of drill pipe, and cost of coring under different contractual conditions. The data are presented in tabular form. The length of the core appears to play a minor part in the percentage recovered, with a tendency to lower percentages with increased core length; approximately 50 per cent of the length cored is normally recovered if the cores are more than 2 in. in diameter. The diarneter of the core has a more pronounced influence on the recovery; 1 3/8-in. cores average 29.1 per cent, 2 1/8 -in. core 53.4 per cent and 3 1/8-in. cores with 6 5/8-in. drill pipe 68.5 per cent. Where 31/8-in cores were taken with smaller diameter drill pipe, i. e., 4 1/2 - in. drill pipe in 8 1/4-in. hole, the recovery dropped to 49.8 per cent, indicating that the more rigid drill pipe favors good core recovery, a conclusion also borne out by the results obtained in using large drill pipe for smaller diame-ter cores. Surprisingly good recoveries were obtained from both the Johnson and Simpson sands; shale, limestone and dolomite each gave less then average recoveries. No serious fishing jobs resulted from coring operations. Attention is called to the need of a core drill which will make it possible to drill a full-sized hole while coring, and thus reduce the cost of cores. Data pertaining to core drilling should be consistently recorded, such as, diameter of drill pipe and collar, diameter of core, recovery, size of cutter heads, type of core-barrel, coring time, speeds of rotation and of pumps, weight on core-barrel, etc.

Jan 1, 1933

By A. B. Stevens, C. J. Coberly

The absolute porosity of a rock or sand may be defined as the volume of the interparticle space expressed as a percentage of the total rock volume. The effective porosity as contrasted with the absolute porosity is the volume of the interparticle spaces which intercommunicate with passages of sufficient size to permit the entrance or recovery of gas or oil, also expressed as a percentage of the total rock volume. A knowledge of effective porosity is of prime importance in estimating the ultimate recovery to be expected from oil and gas-bearing formations. The determination of the effective porosity of a rock includes the measurement of two values: (I) the volume of the rock as a whole, and (2) the volume of the grains and sealed pore space. This paper deals with a new apparatus which has been called a "hydrogen porosimeter" for determining the volume of the grains and the sealed pore space. This volume is determined by means of the pressure relations established in the instrument by the introduction of a known quantity of hydrogen. The Hydrogen Porosimeter The apparatus used in this work consists of an upper chamber for measuring the gas, a lower chamber for holding the sample to be tested, a gage for measuring the pressures, a tank of hydrogen, and the necessary connections. (Figs. 1 and 2.) Of the several gases that might be used for this work, hydrogen has been chosen for three reasons: (1) it deviates less from the gas laws than most gases; (2) it readily penetrates the sample; (3) it is absorbed less than most gases by the solids and liquids with which it may come in contact. Method of Operation After placing the sample to be tested in the lower chamber, the apparatus is thoroughly flushed with hydrogen to remove all air from the system, which is then brought to atmospheric pressure Po. The valve connecting the two chambers is next closed and the pressure in the upper chamber is brought up to a pressure PI by admitting gas from the tank.

Jan 1, 1933

By J. D. Exner

With the introduction of rotary drilling in the Gulf Coast area, some thirty-two years ago, and its subsequent spread to other producing localities in the United States, there has been a constant change in the design of equipment. Only the general features remain, namely the rotating drill stem and the circulating mud. Only recently have the properties of mud and their behavior received attention from petroleum engineers, but circulating problems in present deep drilling demand further study and understanding. It is the purpose of this investigation to determine the relative changes in the apparent viscosity of muds with changes in temperature and to discover other physical effects due to heat. Very little information has been published regarding the effects of temperature on the viscosity of drilling muds. Maustl states: "The viscosity of most muds is decreased on heating, but the interesting thing is that the degree of flocculation is also increased on heating. There will be a greater tendency to seal off formations at high temperatures than at low temperatures." With regard to the effect of temperature on viscosity and yield point, Herrick2 states: "The variation of yield point and viscosity of mud with temperature.....is not very clearly brought out by the data available. Both appear to decrease slightly with increasing temperature up to 200' F." The experimental results presented in this paper further emphasize this point. Two types of viscosimeters are available for measuring the apparent viscosities of drilling muds: the efflux tube type as used by Herrick3 and Marsh, and the torsional type such as the McMichael or the Stormer viscosimeters. Because of its extensive use in measuring the apparent

Jan 1, 1933

By H. C. Fowler

No exact demarcation can be made between producfion engineering and engineering research projects which interest production engineers because the results of today's engineering research make possible many of the applied production engineering methods of tomorrow. A corollary of the development of fundamental research is that so-called practical research becomes necessary. Assuming engineering research to include all subjects related to oil and gas production on which knowledge is being increased through experimentation and through analyses of data obtained from both the laboratory and the field, a review of the work of 1932 shows that the fundamental concepts of at least three major problems have become better understood—bottom-hole pressures, solubility of gas in oil, and fluid movement—and that the established data on the relationships of oil and gas have been applied to obtain more efficient and more economic production of both. Engineers no longer are concerned primarily with the initial development of devices for obtaining the pressures at the bottom of wells. Advancement in the technique of obtaining reliable pressure readings in wells has been rapid. One of the first public suggestions regarding apparatus for obtaining precise information at the bottom of oil wells was made before the Petroleum Division of the A.I.M.E. in 1928. Even during the early development stages in East Texas, reservoir pressures were estimated from well-head observations. Soon, however, a number of proved devices and methods were available, and today bottom-hole pressures in many fields are being recorded and studied as an essential part of the production programs. The research now turns to interpretations of data, obtained with these devices, in terms of reservoir energy and to the development of methods whereby the oil and gas will be withdrawn in accordance with rational and equitable programs based on oil-gas-energy relationships. The term ((bottom-hole pressures" should not be interpreted as indicating the full scope of all research on this problem. By using pressure (and temperature) data obtained in related vertical-flow studies,

Jan 1, 1933

By Stanley Gill

The apparatus is composed of sections of small diameter, seamless steel tubing welded into a continuous flexible tube. At the bottom end a 1/4-in. pipe nipple with a 10 to 15-lb. weight is attached, together with a registering thermometer and a pair of ball check valves. The entire length of tubing is coiled in a single layer upon a drum 4 ft. in diameter which can be attached to the platform of a truck and provided with devices for winding and unwinding the tubing. Connections are made with the upper end of the tubing through a stuffing box, thence to a gas manifold to which a pressure gage is connected. Hydrogen gas is carried in standard 2-ft. cylinders and readings are taken by admitting gas into the tubing from one (or both) of the hydrogen cylinders until the pressure has been built up above that to be measured. At this time the gas supply is cut off. Excess gas escapes through the open end of the tubing and when equilibrium is reached, the pressure is read at the surface gage. Corrections are made for the weight of the column of gas. The advantages claimed for the apparatus include accuracy and the ability to measure the pressures at any number of points without removing the gage. Among the disadvantages of the apparatus are the somewhat bulky size of the equipment and its relatively high initial cost.

Jan 1, 1933

By K. B. Nowels

The attainment of efficient flooding to a large extent depends upon a knowledge of fluid movement through porous media and the pressures used in controlling this movement. Little has been understood con-cerning the fundamental principles involved in the forced drive of water-flooding and an attempt will be made to present some data which may be of interest. Considerable data and technical information pertaining to natural and artificial water-flooding have been presented in the past by Torrey, Umpleby, Fettke, Panyity and others. Their papers have thoroughly covered the description of past and present-day methods of oil recovery by flooding in the Bradford field, especially an article by Torreyl in the Petroleum Engineering Handbook. A bibliography of papers devoted to watcr-flooding, published in Mr. Torrey's article, is appended to this paper. No attempt has been made, therefore, to describe the installations and procedure necessary in flooding, thus permitting the writer to deal exclusively with the mechanics of water movement in flooding operations and its relationship to well spacing. Artificial water-flooding will probably always be the most successful in oil fields described by Herold as being under "capillary control"" and will probably be useless in fields naturally under hydraulic or volumetric control. The natural water drive in an oil field under either of these two controls may give efficient recoveries, as a result of the regulated encroachment of edge water. Such a "natural flood" resulting from the influence of edge water must not be confused with the term as used in this paper, however. Any reference to "natural flood" will here refer to the old method of flooding formerly used in the Bradford field. This was discovered largely by accident and utilized the hydrostatic pressure created by a column of water standing in a watered-out oil well in forcing the oil to an adjacent producing well. The same principles are involved in either natural or artificial flooding, and the latter method simply

Jan 1, 1933

By E. A. Stephenson

In spite of tremendous handicaps notable advances in production engineering have been achieved during 1932. The technique of deep well drilling has continued to progress, notably in California and at Big Lake, Texas. In the latter field a method has been devised by which two grades of oil in contact with each other are produced without intermingling. In rig design many improvements have been made whose objective is to facilitate deep drilling with reduced power losses and increased life of the equipment. Flush joint casing and drill pipe have been improved further, careful tests indicating that the drilling time can be reduced by from 5 to 20 per cent where flush-joint pipe is used. Slow-speed pumping has come into wider use, with further increases in over-all efficiencies. A number of improved well pumps also have been developed and are being tested. One of the most important of these is a positive displacement pump of the rotary type, directly connected to an electric motor placed in the bottom of the hole, and adaptable to various sizes of tubing and casing. In some localities the trend is towards the replacement of electric motors and large-cylinder engines by multiple-cylinder gas engines. Experiments have been conducted and critical analyses made of flow conditions in wells equipped with various styles of tubing which give promise that tubing may be designed to fit individual well conditions. In those wells producing at less than maximum capacity, the gas-oil ratio has been shown to depend on the rate rather than on the method of production, or the design of equipment. Important factors in the design of screened pipe have been carefully analyzed and made the basis of a method for determining the required mesh. Remarkable progress has been made in the use of subsurface pressure data. In East Texas particularly, use of such data is providing a means for the control and equalization of water encroachment and is also pointing the way to a sound means of allocating to individual tracts an

Jan 1, 1933

By R. M. Barnes, A. H. Bell

The ideas set forth in this paper are proposed for consideration and discussion as the result of recent study of various plans for control and proration of gas and oil production from Kettleman North Dome oil field. They would be applicable to any oil field during its flush production stage. The problems of development and proration are so Fig. 1.—Ideal Cross-section, Kettleman North Dome Oil Field. intimately connected in Kettleman Hills and in many other flush fields that they have both been covered in this paper. Many are of the opinion that Kettleman North Dome oil field should be considered as containing only one zone to its present total penetrated thickness of nearly 1500 ft., and that the hydrocarbon content of this zone gradually changes from dark and relatively low-gravity oil with relatively low gas-oil ratios on the flanks and plunges to mostly light-colored and high-gravity oil with high gas-oil ratios in the higher structural positions, somewhat according to the idealized section shown in Fig. 1. At least the lower 400 ft. contains dark oil in the higher structural positions.

Jan 1, 1933

By C. V. Milikan

Allocation of allowed production in a prorated field by the use of bottom-hole pressures is a method which is sound in theory. Thus far it has had limited application because the experience in correlating bottom-hole pressures with the depletion of wells or fields is not sufficient to interpret all the pressure changes. With additional data and more general knowledge of bottom-hole pressures their use in proration will probably become common. Bottom-hole pressure is the pressure at or near the bottom of a well. It is usually determined at the face of the producing horizon. Bottom-hole pressure measured while the well is producing, may be called the bottom-hole producing pressure or bottom-hole flowing pressure. If the well has been shut in or shut down long enough for the pressure in the producing horizon within the drainage area of the well to equalize, it may be called the reservoir pressure. The allowable production from a prorated field may be allocated to the individual wells or leases by three methods: 1. Bottom-hole producing or flowing pressures. (a) The potential capacity of a well to produce. (b) A uniform differential pressure while producing at the allowed rate. 2. Reservoir pressures. 3. A combination of bottom-hole producing pressures and reservoir pressures. In most prorated fields the allowed production is allocated to the individual wells or leases in proportion to their individual potentials. This method is based on the theory that there is a direct relationship between the permeability and the porosity of the reservoir. More directly stated it means that there is a direct relationship between the amount of oil in the reservoir and the rate at which it will move through the reservoir. While in general this relationship is true, it may vary considerably in different wells. Furthermore, in many wells the capacity of the reservoir to deliver oil to the well is greater than the capacity of the flow string to deliver oil to the surface. It is especially true where the potential is determined by flowing through tubing or by pumping.

Jan 1, 1933

By Clifford S. Wilson

ScReened pipe is designed with the view of restraining the fine, free-running sands of the production zone from entering oil wells. Its successful use is dependent on a number of factors. The nature and effects of some of these factors can be determined through experiment and observation, but some of the elements that have a distinct bearing on the use of screened pipe can be evaluated only by estimate. The important subsurface conditions which affect the use of screened pipe are: 1. Depth of production zone. 2. Extent of production zone. 3. Reservoir pressure. 4. Character and relative quantity of oil and gas. 5. Character of sediments: a. Cossolidation of beds. b. Variation in beds. c. Grain-size gradation of sands. d. Free-running characteristics of sand from different levels. Aside from the use of mechanical equipment and tools, the measures to be taken in the installation of screened pipe involve: 1. Size of liner. 2. Length of liner. 3. Design and mesh of screen. 4. Portion of liner to be screened. 5. Manner of setting liner. 6. Preparation of or washing of the well before or during the setting of the screen. 7. Manner of bringing in the well. 8. Manner of flowing the well. Values applicable to the actual subsurface conditions that exist at any well can only be approximated. The accuracy of the estimate will be measured by the amount and quality of the evidence at hand and the personal factor of ability to interpret the evidence fairly, whether

Jan 1, 1933

By F. G. Tickell, R. C. McCurdy, O. E. Mechem

The behavior of fluids in the voids of a rock is fundamental to the study of many of the problems of oil-field development and production. For it is by virtue of these openings between grains that oil and gas are able to move through the rock, to be contained by the rock, and to pass from the rock into the well. The capacity to contain fluids is measured by the porosity of the rock, and the ease of fluid movement is governed by the permeability. When the engineer wishes to estimate the amounts of oil and gas in an underground reservoir he is often concerned with the porosities of the rocks and, when dealing with problems relating to rate of production, he is more likely to be interested in the permeabilities of the rocks. Rocks are permeable because they are porous, but they may be porous without being permeable. Clays are very porous, and yet they are impermeable from a practical standpoint. Attempts have been made1 to correlate permeability with porosity for certain rock members but, where a definite relationship between these two properties is found to hold, it is purely fortuitous and local. Porosity and permeability do not necessarily bear any quantitative relationship to one another. The porosity of a substance is the percentage of void volume to bulk volume. The petroleum engineer is usually interested only in the inter-granular voids that are accessible to fluids. In measuring porosity he does not wish to include scaled openings. The measurement he desires is one of "available porosity," otherwise called "apparent porosity." The porosity of a natural aggregate of solid grains, such as a sandstone or clay, is governed by: (1) Grain-size distribution, (2) angularity of grain, (3) colloidal content, (4) degree of compaction. It is not difficult, for unconsolidated rocks, to measure the effect of any one of these when it alone is varied, and then to predict what the effects on porosity will be for such single variables. It is very difficult, however, if not

Jan 1, 1933