Search Documents

Reduce dust on long wall faces by using a gob curtain to lower air leakage Into the gob and raise the airflow along the face. Approach A brattice curtain (gob curtain) Is hung between shield #1 and the rib in the headgate entry forcing the ventilating air stream to make the 90° turn and stay on the face side of the shields rather than leaking into the gob. How It Works Air leakage is greatest in the headgate area because the gob behind the first few shields remains open due to the roof bolts in the headgate entry. In addition to the open gob, there is a large gap between shield #1 and the rib. Prevention of air leakage behind the shields is accomplished by the Installation of a curtain between the first shield and the rib extending from the roof to the bottom. The curtain Is advanced with the shield line each pass and is helpful In maintaining a sufficient air quantity along the face. The biggest Improvement due to this curtain is seen in the first 25-30 shields where the Increased air volume lowers dust concentrations through dilution.

Jan 1, 1981

Reduce methane levels around the shearer machine during longwall mining by directing more of the available airflow along the face and over the shearer body. Approach To address the entire mining cycle, two techniques were combined to dilute and clear the methane liberated from the face by the shearer during cutting. The first is the modified shearer clearer system, which is used during the entire face pass. This is combined with the walkway curtain which is used only during the headgate cutout. How It Works Methane ignitions are one of the most potentially serious hazards facing longwall mine operators. The high rate of coal extraction on longwall sections can liberate a significant quantity of methane during a pass. The modified shearer clearer is used to dilute methane concentrations along the entire face for both cut directions. The shearer clearer system, originally designed as a dust control technique, uses a series of water sprays located on the shearer body to direct more airflow along the face and over the shearer. (See Technology News issues, #112, #118, and #221). The only change from the original shearer clearer design is the addition of three sprays to the return-side splitter-arm/ shearer interface. The additional sprays help to ventilate the area behind the shearer body.

Jan 1, 1985

By Henry Chumienski

Next to the paper industry, the steel industry is a major user of water. Without an adequate and reliable source of “good” water, steel cannot be produced. The use of water has a direct impact on steel quality and on our environment. Used improperly, water can also add unnecessary costs. Used properly, water can maintain and improve steel quality, enhance our environment and control or reduce the “total cost of operation”. Water needs to be more than just “wet and not lumpy”. Water quality needs to be based on the end use. This paper discusses ways to manage many of the water systems. With little or no capital investment it is possible to develop operating practices that protect your initial investment, ensure that the water systems do not have a negative impact on quality or your production costs and also minimize your chance of having an environmental incident.

Jul 30, 2018

Presentation Agenda ?Background ?OEM Recommendations before RCM ?Operating Context ?OEM Recommendations after RCM ?Reality of Failure ?RCM Deliverables ?Maintenance program optimization ?Spare part optimization ?Implementation ?Further Considerations -Three scenarios ?Summary and Conclusion Background ?P&H Mining?s LCM division performed a RCM study on a ?generic 4100 XPB shovel?in Milwaukee. ?P&H soon realized that the analysis required context -The recommendations were manufacturer knowledge based. -The outcome based on manufacturer requirements. -The strategy was not applicable to all machines, etc. Operator experience and ?local knowledge? are key to the success of an RCM analysis. P&H approached Teck Coal?s Fording River Operation to assist with ?Operating Context?. Teck provided operator and maintainer experience.

May 1, 2010

By Justin Carl, Aliuddin Mohammad, Gordon Evans, Steven Bealby, Carlton Ray

"The District of Columbia Water and Sewer Authority (DC Water) is implementing the $2.2-billion DC Clean Rivers Project (DCCR) to control combined sewer overflows (CSO) to the Anacostia and Potomac rivers and Rock Creek, and to provide flood relief to the Bloomingdale and LeDroit Park neighborhoods in the District of Columbia. The long-term control plan complies with the requirements of a Federal Consent Decree entered into by DC Water, the District of Columbia and the United States, as represented by the U.S. Environmental Protection Agency and the Department of Justice. The Northeast Boundary Tunnel, a design-build project, will store combined sewage and deliver it to a system of downstream tunnels and ultimately to the Blue Plains Advanced Wastewater Treatment Plant (Blue Plains), where it will be treated. In addition, the Northeast Boundary Tunnel (NEBT) is a major project associated with the mayor’s task force to alleviate extreme flood events in Bloomingdale and LeDroit Park. The Northeast Boundary Tunnel Utility Relocations (NEBTUR) design-bid-build (DBB) project is an accelerated component of the Anacostia River System, as shown in Fig. 1. During dry weather conditions, the entirety of the sewage in the combined system is conveyed to Blue Plains.During storm events, when sewer pipe capacity is exceeded, the flow, which is a mixture of sewage and stormwater runoff, overflows into receiving waters through outfalls. There are a total of 47 active CSO outfalls along district waterways.The influx of storm runoff into the combined sewer has an additional impact on the communities of Bloomingdale and LeDroit Park. The sewer system is outdated and undersized. In these neighborhoods, when the capacity of the sewer is exceeded, localized flooding occurs and backups into adjacent residences are prevalent. In any given year, there is a 50-percent chance that flooding will occur in these neighborhoods."

Jan 9, 2017

By L. Darkwah

The use of explosives in coal mining inevitably results in oversize, midsize and undersize (fines) products due to fragmentation. The oversize can be broken into smaller sizes by further processing. However, the undersize have a negative affect on the efficiency of a mining operation. Therefore, limiting the amount of fines can be economically crucial. This paper concerns investigations aimed at reducing fines generation in coal mining. Inherent fractures were identified as one of sources of fines generation. This paper is centered on establishing a relationship between the fracture occurrence, the explosive properties and the blast outputs, which are evaluated in terms of the fines generated.

Jan 1, 1998

Explosives are used to mine coal. Any blast results in three size categories of products, namely over-, middle-, and under-size. Boulders can still be broken smaller in further operations after blasting. The under-size, for instance coal fines, negatively affects the mining efficiency. Their reduction ensures better returns. The paper concerns investigations aimed at reducing coal fines' generation. Inherent fractures are identified as one of source of fines. The discussion is therefore centered on establishing a relationship between the fracture occurrence, the explosive properties and the blast outputs evaluated in terms of the fines generated.

Jan 1, 1996

By J Say, M Hawtin, L Carlon, P Cann

Historically, production from sublevels of the Ernest Henry Mine (EHM) started from blind uphole rises at the end of slot drives. Where previous investigations considered removing these slot drives and starting production with independent ore drives, any development savings were consumed when drives were extended to minimise ore loss. Since 2017, EHM and Orica have been investigating opportunities to optimise drill and blast practices by implementing Orica’s Wireless Electronic Blasting System (WEBS). To reduce ore drive development metres, a novel design was proposed utilising the WebGen™ 100 system to combine a rise with pre-charged widening firings. Initially these new rise and widening firings achieved results similar to previous EHM designs, achieving on average 81 per cent of design height and width. Due to poor performance of the fourth trial a significant re-design was required. Modifications included drill hole re-positioning, in-hole primer relocation and initiation delay adjustments. Since the re-design a step change in rise performance has been observed with rise and pre-charged widening shots averaging 95 per cent of design height and width. With rise and widening performance exceeding expectations, the removal of slot drives has allowed a substantial reduction in lateral development. Development savings of 165 m and 169 m from the RL1325 and RL1300 levels have been achieved. Primary draw and ore recovery has also increased due to the later addition of pre charged forward stripping rings. Level design changes have also significantly improved the mining cycle by allowing for a reduction in required ground support, improved secondary ventilation, a reduction of critical path development, simpler production scheduling and less wear and tear on machinery. Future mine level designs now incorporate key learnings and are proving beneficial to a variety of scenarios including changing orebody boundaries at depth.

Mar 15, 2021

By S. Pinard, J. MacLellan, G. Ehlert

"The Kidd Creek concentrator is looking actively for alternative technology as means of reducing operating costs in their concentrate handling section. The use of pressure and vacuum filters to eliminate the multiple hearth dryers would have the most beneficial effect. The dryers which constitute the greater portion of concentrate drying costs consume about 35,000 m3 per day of natural gas.After the evaluation of various filters by Kidd's technology group, it was clear that, because of the low final moisture requirements of 5.5 to 6% H20, few filters were able to achieve this target economically. Lately attention has focused on the Andritz hyperbaric filter. Testwork has shown that target moistures can be achieved with an appreciable reduction in operating cost.1.0 INTRODUCTIONThe Kidd Creek Concentrator is located 28 kilometers east of Timmins, Ontario. The ore is hauled by the Kidd Creek Railroad to the concentrator where it is milled to produce separate copper and zinc concentrates.Projected concentrator feed for 1991 is 3,750,000 tonnes of ore grading 3.3 % Cu and 4.7 % Zn. The concentrate production is expected to be 458,080 dry tonnes of copper concentrate at a grade of 25.7 % Cu and 265,020 dry tonnes of zinc concentrate at a grade of 54 % Zn.Currently, there is active investigation toward cost reduction through implementation of new technologies. One area which has been extensively evaluated is the concentrate dewatering and drying section. In that section, the multiple hearth concentrate dryers represent the largest source of operating costs, mainly through maintenance and energy costs (electricity and natural gas). The replacement of these dryers with filtration technology that could produce the required concentrate dryness would represent substantial savings.In September of 1990 filtration testwork carried out by Andritz Ruthner showed that Kidd Creek copper and zinc concentrates could be filtered to below 6 and 8 % moisture respectively. In late May 1991 the laboratory testwork was duplicated on siteand one month later a 5 m2 pilot filter was tested on site. Based on the pilot test results, an economic evaluation was performed. It indicated that a reasonable payback could be realized if hyperbaric filters were to replace the existing concentrate drying section."

Jan 1, 1992

By Michael S. Wieland

Delay detonators that are damaged by cross-hole wave interactions degrade blasting work and raise the risk of incidents. Damaged detonators impose risk, because they can retain sensitive explosives that respond to stray energy during recovery, inspection or disposal. Laboratory techniques were developed to rank the ruggedness of delay detonators under replicated field-shooting conditions. The hazards are tremendously magnified if trial detonators are installed directly in secondary explosives to rank initiation strength. Therefore indirect ranking techniques were sought that mitigate the risks without compromising the worthiness of the method. Four types of hardware fixtures, referred to as simulators, were developed to yield distinct forms of transient compression. The shock and rift versions generate compression pulses representative of in situ waveform components. The waiting time, until the trial detonator functions, duplicates typical delay periods. The trial detonator is mounted within water, which has a density and inertial resistance comparable to most blasting explosives. The work output from the trial detonator explosion is registered as fixture wall-expansion. This work output determines malfunction results, regardless of which type of simulator is used.

Jan 1, 1997

By S. D. Viljoen

The use of ceramics to protect equipment subjected to wear in abrasive and corrosive applications has been accepted by most plants as the industry norm. Little is, however, known about alternative special ceramic based products which are available for the protection of plant assets. With careful engineering, impact resistant ceramics can be used in high impact zones using modern ceramic technology. Properly selected and properly installed, ceramics will provide a tough wear resistant lining for protection against abrasion and impact. Basalt, on the other hand, is widely used in coal washing plant process pipes with varying degrees of success. Basalt is normally not used for the lining of bends, ?T? pieces or reducers due to the reduced wear resistance compared to alumina ceramic. The advantage is a much reduced initial capital cost. A patented ceramic composite non-return valve solved an old problem encountered in the operation of medium sumps. The design approach overcomes the lack of functionality of alternative designs and reduces valve wear while preventing medium settlement during plant shutdown periods. Direct bonded ceramic pulley lagging is becoming the industry norm, eliminating most of the problems encountered with conventional pulley lagging systems.

Jan 1, 2010

By B. S. Xakalashe, M. Khama, Q. G. Reynolds

Pre-reducing chromite with hydrogen offers significant benefits, including reduced energy consumption in downstream smelting and lower carbon dioxide emissions. To leverage these advantages, it is essential to develop computational models that facilitate the design, optimisation, and control of the process. Full scale models such as 3D computational fluid dynamics models are often used to investigate the multi-scale flow physics in heterogeneous reactors. However, these models impose prohibitive computational expense in the modelling of heterogeneous reacting flow systems. The high computational expense prevents the use of high dimensional systems in real time control and online optimisation of reacting flow systems. In order to facilitate incorporation of predictive models in the heterogenous reacting flow systems control loop, computationally efficient reduced order models are required. Owing to these requirements, a reduced order model for pre-reduction of chromite with hydrogen was developed with the view to rapidly predict the performance indicators for pre-reduction of chromite with hydrogen. The Thiele modulus method was used to develop the reduced order model, and the model results were compared to isothermal pre-reduction experimental results at a range of pre-reduction temperatures from 1200 oC to 1400 oC. The model predicts the degree of reduction, diffusion of gases through the product layer, unreacted core radius of the grain radius, and local and global conversion. The final conversion across all temperatures as predicted by the reduced order model deviate from the experimentally calculated conversion by a maximum relative error of 2.7% while the initial conversions differ significantly, reaching a maximum error of 65%.

Aug 3, 2026

By John R. Jr Tripi, Paul N. Worsey

Split round blasting is commonly practiced in underground uranium mining in the Big Indian ore belt located in Southeast Utah. The technique is used to prevent ore dilution by separately blasting the ore from the face.

Jan 1, 1985

By David D. Gallagher

Customer demand for greater efficiency and reduced operational costs on modern overland conveyors has focused attention on the conveyor belt's rolling resistance properties. Studies have indicated as much as 60% of the power losses on a long horizontal conveyor can be attributed to the indentation of the pulley cover rubber as it passes over idlers. This paper will compare tan delta values of different compounds with large scale rolling resistance test data from the University of Hannover. Results will then be compared to actual power consumption data gathered on several long overland conveyors using identical belt construction except with different pulley cover compounds. Concluding comments will be made indicating substantial operating cost differences based on the rolling resistance of the cover compound.

Jan 1, 2000

By Michel Rodrigo Luiz, Glaudistoni da Silva Félix, Osmar Duarte Junior

This article deals with a project to reduce the preparation time and threading the coils in the input section of a pickling line coupled to the cold strip mill (PLTCM) at ArcelorMittal Vega. The project developed serves for the detection and elimination of bottlenecks in the input section. The project was conceived by the philosophy of the Theory of Constraints (TOC) and Lean Six Sigma (6 sigma), here seen as sequencing serial / parallel in the preparation and threading the coils. In this context, a proposal to modify the automatic sequencing and reduction of interruptions due to failure of the automation / equipment confirmed its effectiveness reducing the total time preparation time and threading the coils in the entry section by 15%. This project was developed without investment costs, bringing gains on the order of US$613,769.00.

Oct 1, 2019

One-half fare return rate again available to members of the Institute and dependent members of their families. DON'T FORGET YOUR RAILROAD CERTIFICATE Over 300 members of the A. I. M. E. and dependent mem-bers of their families attending the last annual meeting se-cured return railroad tickets at half price by means of the railroad certificate, thereby saving several thousand dollars. DIRECTIONS 1. Be sure to obtain your railroad certificate when pur-chasing your railroad tickets for the meeting or you will lose money. 2. Purchase your tickets at regular one-way adult tariff fare between the dates specified for your territory in the accom-panying table. 3. Present your certificate for valida-tion at Institute headquarters in New York immediately after registration. Certificates will be validated on Feb. 21 and 22 between 9 a. m. and 5.30 p. in. 4. You must use your return half-rate tickets not later than Feb. 27. 5. Use the same route for both going and return trip. PLEASE REMEMBER THIS 1. Unless-250 certificates are validated at headquarters it will be impossible for anyone to secure the reduced rate. 2. Unless you secure a certificate you cannot take advantage. of the half-rate return fare, even if the necessary 250 certificates are validated.

Jan 2, 1928

By J. Eric Nylund

"Intensive mechanization and automation in the LKAB, Kiruna Mine in Sweden have resulted in substantial rise in productivity and decrease in production cost. Capital investment in a modern mine today averages a considerable amount per miner and costs increase with requirements for more efficient methods and equipment. Equipment reliability becomes more and more important. Equipment maintenance requirements are directly proportional to equipment reliability and grade of availability. Weaknesses in the equipment result in unnecessary costs with regard to maintenance which can add up considerably per year, but of more importance are the costs caused by equipment breakdown. These breakdowns disturb or interrupt the production and often cause damage to other parts of the system. This paper discusses the important parameters involved in mine car wheel wear and the design principles of wheels, axle suspension and track.IntroductionTrains operating in an underground mine do not follow the same standard of performance as trains operating on surface railways. The differences in speed, curve radius and environment require different methods of calculation for underground train systems, and when judging the parameters involved one must keep in mind these differences at all times.While surface railway technology was given all possible attention over the last century no one was seriously looking into underground rail haulage in the sense of rail vehicles performance on the track until LKAB in 1975 started to question the methods of calculations used. Even though LKAB by then attained mine car maintenance cost that was 1/6 to 1/10 of other mining companies they were not pleased with the situation. The objective for the ensuing engineering work was to derive the reasons for wear and breakdowns. Once those reasons were established, the design of a completely new generation of mine cars could start. The result of these efforts were beyond all expectations. The maintenance cost on mine cars had been reduced to 1/15 of prior car generation which already had comparatively low cost.The most significant cost savings were made on wheel maintenance, which earlier represented 50% to 55% of car maintenance. Wheel life was increased from an average of 3 to 30 years or more.The LKAB theories around wheel wear are described in the following report."

Jan 1, 1987

By J. T. Price

The study was undertaken to investigate the effect in the charge to a blast furnace of zinc and alkali contents, which tend to form accretions and scaffolds in the upper sections of the furnace. Commercial iron oxide pellets were reduced in a CO:N2, 40:60 gas mixture in a 5-cm by 5-m counter-current reactor (Rist-type apparatus) designed to simulate blast-furnace conditions. Pellets from a commercial magnetite concentrate were prepared in the laboratory with zinc (1% ZnO) and alkali (1% KOH) additions to the concentrate. Reducibility, crushing strength and swelling tests were carried out and the results compared with test data from pellets prepared without additions. The results indicated normal behaviour for those pellets containing zinc, whereas those containing alkali swelled catastrophically under the same reducing conditions.

Jan 1, 1977

By Phillip J. Maddex

After the presentation of a co-authored paper, "The Cost of Transporting Ores and Raw Materials in World Markets", at the February SME meeting, one questioner commented, "You have been talking about the large shipper and ship loads. What does the small shipper do?" This paper will attempt to answer that question, at least in part. Probably the questioner hoped to hear about specific new tools and new techniques that he could apply. But one paper could only scratch the surface of the vast fund of information available; so rather than talk specifics we should take basics, that is, people, management and technology.

Jan 1, 1967

By Pierre DePasquale, Ricardo Chavez

Lowering of quarry energy consumption participates to answer both environmental and financial issues. The “EE-Quarry” European project, supported by the European Commission (EE stands for Energy Efficient), develops a new and highly effective modelling and monitoring Energy Management System technique to improve Energy Efficiency and move to a low CO2 emission rate in the nonmetallic mineral industry. Within this global quarry project, blast design, as the first link in the chain, has to be optimized in order to satisfy requirements of downstream operations. The authors have been developing and implementing an operational methodology using continuous field measurements and field adaptation methods for blast design. It drives the drilling and blasting work, aiming at a more energy efficient and environmentally friendly operation. Based upon actual local conditions (rock-mass assessment, face geometry, borehole deviations, etc.), blast patterns are optimized through a specific hole-by-hole blast design software. It provides a better and more consistent energy distribution, to achieve a better rock fragmentation, while avoiding explosive overconsumption. The software also calculates total energy inputs and the drilling and blasting contribution to Greenhouse Effect. Coupled with methodical fieldwork and variable density explosives, it has been leading to a real reduction in energy costs and greenhouse gas emissions. As the project is now reaching its final stage, demonstrations were conducted in various quarries around Europe. Several simulations were carried out and compared to the site data, in order to propose enhancements for the different phases (extraction, loading, hauling, crushing and transport) while bearing in mind the environmental impact of the quarry. This blasting methodology allows to assess the carbon footprint of drilling and blasting in conjunction with the downstream operations, thus to evaluate the global carbon footprint of quarrying. Copyright ©

Jan 1, 2015