Search Documents

By Bill Zietlow

A micropile and soil nail underpinning system was installed to support a building immediately adjacent to a 25-ft deep excavation in downtown Salt Lake City, Utah. Both the building and the underpinning were instrumented to monitor deflections, rotation and crack growth. The underpinned structure consisted of a two story concrete masonry unit (CMU) building founded on shallow spread footings attached to a concrete high-rise building on spread footing two floors below grade. The face of the excavation was 10 in. in front of the underpinned building foundation wall. The underpinning system consisted of small diameter hollow bar micropiles installed with injection grouting techniques below the bottom of the excavation and attached to the underpinned structure by a concrete pile cap doweled into the existing footing. The lateral loads imposed by the soil under the underpinned structure were designed to be supported by the soil nail wall installed through the micropiles during excavation. The settlement monitoring instruments consisted of crack gages, optical survey prisms, high sensitivity vibrating wire water levels and biaxial vibrating wire tilt meters. They recorded maximum movements of approximately 0.1 in. of settlement, 0.05 deg. rotation (top of wall rotating away from excavation) and up to 0.08 in. of crack opening during the excavation until one month after the soil nails and shotcrete facing were completely installed. This movement was well within both the estimated settlement and the estimated settlement tolerance of the underpinned structure.

Jan 1, 2008

By Richard A. Forth

During the construction of the Island Line (ISL) in Hong Kong between 1982 and 1986 piled foundations of a building were encountered in a tunnel drive. As the tunnel alignment could not be changed work was temporarily suspended whilst grouting took place beneath the pile cap. The tips of the piles were then cut off. The normal precast concrete lining segments were replaced by the "stiffer" spheroidal graphite iron segments and tunnelling resumed. Settlement of the building was found to be under 10 mm due to the tunnel drive and no damage was reported to the building.

Jan 1, 2002

By J. Don Scott

Analytical predictions of the rate and magnitude of settlement of deposited oil sands tailings slurries generally overestimate how fast pore pressures will dissipate. Field deposits of nonsegregating tailings to mature fine tailings show continued high pore pressures near the surface which impede surface reclamation. In geotechnical analyses which predict the consolidation behavior of soft soils a finite strain theory is used. Effective stress-void ratio and void ratio-hydraulic conductivity relationships determined from laboratory large strain consolidation tests, are used in the finite strain predictions. This theory, however, cannot predict the full range of sedimentation, consolidation and pore pressure dissipation which occurs in large scale deposits of thixotropic tailings slurries. A new large strain consolidation model which assumes that the creep rate of the slurry exceeds the pore pressure dissipation rate is being investigated. This model is relevant for rapidly deposited, low permeability thixotropic slurries where the upwards drainage path increases by several meters a year, such as, in oil sand fine tailings ponds and nonsegregating tailings deposits. The model will be verified by analyzing the 10m high column of fine tailings at the University of Alberta which has been monitored for over 20 years and in which the excess pore pressures are still very high.

May 1, 2004

By Rudolph P. Frizzi

This paper presents different deep foundation systems and associated settlement records for high-rise building projects in the coastal areas of southeastern Florida. An introduction to the sedimentary soil and soft rock geology in coastal areas of southeast Florida is presented, and the deep foundation systems utilized include: piles of varying length, pile supported mat, preload and short piles, and drilled shafts. The implementation and associated settlement monitoring data of the different deep foundation systems are described through case histories involving 20 to 66-story buildings. In addition, the deep foundation systems and settlement monitoring results for twenty-one additional high-rise building projects in the coastal areas of southeastern Florida are presented.

Jan 1, 2003

By Swaminathan Srinivasan, Aaron J. Muck

"When an opportunity arises to combine state-of-the-art concepts with advanced modeling tools, engineers need to take what they know and apply forward thinking to geotechnical solutions to promote the state-ofpractice. Such an opportunity was seized during the design and construction of the Great American Tower in Cincinnati, Ohio. The forty-one story Great American Tower at Queen City Square – currently the tallest building in Cincinnati – has not only changed the downtown skyline, it is also contributing to the advancement of the state-of-the-art use of auger cast-in-place (ACIP) piles as settlement reducers. Predicted settlements of a traditional mat foundation were excessive, and the costs and construction time associated with traditional ACIP piles extending to bedrock were not preferred. A mat supported on a limited number of ACIP piles, with the piles primarily acting as settlement reducers, was evaluated as the preferred foundation type.Promoting the unique soil-structure interaction of the foundation system with confidence required the use of sophisticated numerical modeling tools. Traditional standard penetration test boring data (SPT) was initially used to develop a numerical analysis of the soil-structure interaction using FLAC 3D software. The model was further modified with cone penetration (CPT) and pressuremeter testing (PMT), along with actual load test results on several ACIP pile elements of varying lengths, but all tipping above bedrock. Through a combined design team effort, and detailed numerical modeling analysis, ACIP piles were recommended for reducing mat foundation settlement. Instrumentation during and post-construction confirmed design assumptions and predictions. Integrating sound geotechnical concepts, and using advanced geotechnical analysis and design methods, traditional mat and ACIP pile foundations were successfully integrated into a unique foundation support system.INTRODUCTIONThe Great American Tower at Queen City Square in Cincinnati, Ohio is located within a region dissected by historical geologic deviances associated with the meander of the Ohio River and glacial progression/recession. Combining a challenging geology, with the development of a high-rise office building afforded the design team an opportunity to combine state-of-the-art soil-structure interaction concepts and method with traditional geotechnical engineering concepts. Such a combination required a variety of field tests, collaboration with the design team and owner, and geotechnical-structural modeling during the design phase. During construction, in addition to materials testing and observation, a variety of instrumentation systems were employed. Together, the data was used to corroborate the design model and make adjustments during construction and further substantiate design assumptions following construction."

Jan 1, 2015

By Werner Bilfinger, Claudio Nahas, Marcelo Waimberg

"INTRODUCTION The so called Porto Maravilha Project consists of the re-urbanization of a 500 ha area in the Rio de Janeiro port region. Several changes in local infrastructure are being implemented, including a significant change in the road system, with the demolition of the former “Via Perimetral” viaduct and construction of 4 new tunnels: • Saúde tunnel - 35 m long (Waimberg et al, 2014); • “Binária tunnel” - 1012 m long; • “Via Expressa” twin tunnels - 1850 m long each way. The tunnels were excavated almost completely in rock using conventional drill and blast methodology and only some short stretches in weathered rock, associated to faults zones, residual soils and marine sediments close to the tunnel portals. During excavation of access shaft and “Via Expressa” and “Binária” tunnels significant ground settlements as well as settlements of buildings founded both on shallow and deep foundations were measured. These values could not be associated to conventional tunneling induced settlement troughs. This paper focuses on the “Via Expressa” tunnels, presenting a brief description of the project as a whole, its geological and geotechnical background, monitoring results, and a discussion of possible causes of the measured settlements. PROJECT DESCRIPTION The Porto Maravilha Project is an integrated multidisciplinary action on behalf of the Rio de Janeiro city council with support from the State and Federal Governments. In addition to creating new conditions for working, housing, transport, culture and leisure for the resident population, it also promotes expressive economic development in the region (Portonovo, 2015). Porto Maravilha Project is carrying out actions for the recovery of the region’s historical heritage, as well as promoting the population´s social and economic development. One of the main benefits of the Porto Maravilha Project is the construction of the new traffic system in the port area, consisting of the Express and Binário roadways. The new project, which will replace the current Perimetral Rodrigues Alves viaduct system, will increase traffic flow capacity by 27%."

Jan 1, 2016

By Fred C. Bond

A study of the settling and thickening of finely divided pulps was undertaken with the object of obtaining certain fundamental relationships, with resulting improvements in the design and operation of mechanical equipment. The subject has been treated in two parts: testing and batch thickening, and continuous thickening, including calculations of capacity and dimensions. Part 1. ? Testing and Batch Thickening The usual method of making thickening tests is to agitate the pulp with a plunger in a graduated glass cylinder and let it settle, while recording the time rate of settling. The settling rates corresponding to different pulp dilutions are found, the ultimate dilution obtained is measured, and the necessary thickener area in square feet per ton of dry solids per 24 hours is calculated, for each pulp dilution. The largest area found is used in selecting the proper thickener size.

Jan 1, 1946

By Jan Steinhoff

The design options of a gravity separator are still limited and rely on the study of settling behavior. A methodology will be presented where an experimentally given inlet droplet size distribution (DSD) is the basis for the calculation of the dispersion layer in a gravity separator. A pilot-scale continuous gravity separator is presented and CFD (computational fluid dynamic) results are validated. A transmitted light measurement technique for the determination of the DSD is presented up to a holdup of 15% dispersed phase. The resulting DSD was in the range of 20–2000 μm depending on flow rate and phase ratio. Furthermore, correlations of the real DSD with the settling behavior of the dispersion in a settling cell are discussed. The new approach to the description of gravity separators will be presented and the applied CFD methods showed good results with the system water/paraffin.

By A. A. Gustafson

IN diamond or churn drilling for the prospecting of ore bodies, two products can be used for quantitative analyses; i.e., the core and the cuttings, or sludge. Some operators prefer an assay of core; others insist that the sludge be sent for analysis. Both must recover the sludge for check samples or for assays if there is no core recovery for any particular section of the diamond-drill hole. The Freeport Sulphur Co. found that numerous cumbersome sludge boxes or barrels were inconvenient and delayed drilling. The sludge settled slowly in the ordinary shallow, rectangular diamond-drill boxes and its total removal from the container was difficult, time-consuming and unsatisfactory; and sampling of deposits of which the metal contents are easily concentrated, as in ores containing cinnabar, gold and silver, is subject to error if the boxes are not thoroughly cleaned. Mr. Charles Ballard, dredge superintendent at Freeport's operation at Grande Ecaille, Louisiana, developed a portable cone while he was in charge of prospecting a mercury property near Tonopah, Nevada, in 1040. Ballard later improved the design while the settler was being used at a manganese property in New Mexico. The operation is based on the "free settling" of comminuted particles in a quiescent liquid. The ordinary sludge box discharges over a lip 8 to 12 in. wide and consequently the water has sufficient velocity so that the discharge water is never clear. The cone settler used by Freeport Sulphur Co. discharges over the entire circumference, which gives a discharge lip of 9 ft. in the size of cone used at the cinnabar and manganese prospects. Consequently, the velocity of the discharge water is slow enough so that all fine material settles and the discharge water is clear. When the drilling of a sample interval is complete, the sludge can be drawn off by the time the driller is ready to cut another sample. Thus, only one cone is needed per drill. The cone has been used by Freeport successfully in churn-drilling a manganese deposit, in diamond-drilling a mercury deposit, and in diamond-drilling a deposit of ore containing tin, copper, gold and silver. The cone is greatly superior to the old methods of collecting sludge and is now used on all Freeport drilling campaigns in the western states, both for surface and underground drilling. Fig. I shows the important details of a cone designed for average operating conditions, 30 in. in diameter and 36 in. high. Abnormal conditions may require some revisions in design. Fig. 2 shows a working drawing. A hose or pipe larger than the one used to convey water from the pump to the swivel head of the string of rods is connected to the stuffing box at the collar of a diamond-drill hole. The usual T-connection is used. It is not necessary to use a stuffing box if the top of the cone can be placed lower than the collar of the hole. Then the return water and cuttings can be made to flow by gravity. This hose or pipe discharges the cuttings of the drill bit and the return

Jan 1, 1943

By V. F. Swanson

A mathematical model for free and hindered settling of minerals was developed. This paper describes how to apply the model in designing systems, such as fluidized bed, elutriation, mixing pumping systems, involving solids and fluids.

Jan 1, 2000

By Lucas Nana Wiredu Damoah, Lifeng Zhang

"Increasing demand for Solar Grade Silicon (SoG-Si) due to rising interest in renewable energy has lead to increased SoG-Si Top – cut scraps generated from the multi-crystalline silicon making process. Due to the high cost of SoG-Si and the potential to use the top-cut scraps as feedstock material, there has been increased effort to develop cost effective and efficient technologies. As a result, several methods to recycle the top-cut scraps are currently been applied, and researched. These include settling under gravitation field, which is a slow process to be industrially applicable. Natural settling of inclusions by gravitational force is a slow process and not attractive to the industry. Recent experiments on Top-cut SoG-Si scrap under high frequency, high voltage, electromagnetic field showed that SiC inclusions settled within a short time to the bottom of the crucible and the characteristic rod-like morphologies of Si3N4 inclusions in SoG-Si were not detected. This study investigates the enhanced settling of SiC inclusions and the behavior of Si3N4 particles under the influence of high frequency, high voltage, electromagnetic field in Top-cut SoG-Si.IntroductionThe photovoltaic industry depends on silicon based PV materials either as single-crystalline silicon, or multi-crystalline Si (MC-Si), or amorphous Si [1] for over 90 % of its market share. [2] MC-Si produced by directional solidification of solar grade silicon melt dominates the silicon PV market. During the directional solidification process, SiC and Si3N4 particles within the melt are pushed by the solidification front to the top of the ingot which is the last to solidify. Therefore the top of the ingot is cut generating what is known as top-cut solar silicon scraps. The Si3N4 particles are mainly from the coating material at the inside surface of the silica crucible and from air absorption during the solidification process. The SiC particles mainly stem from the carbon reduction process of the primary production of silicon [3]. Due to the growth of the PV industry as a result of global demand for clean, reliable, and affordable energy [4], there is the need to develop new methods to compliment exiting ones to recycle SoG-Si waste (e.g. top-cut) for sustainability."

Jan 1, 2012

By H. L. Monroe

Meramec Mining Company, owned 50% by St. Joseph Lead Company and 50% by Bethlehem Steel Corporation,- is engaged in the mining, concentrating and pelletizing of iron ore from the Pea Ridge Mine which is located in the rugged, wooded Missouri Ozarks about 15 miles from the town of Sullivan or 75 miles southwest of St. Louis. The orebody was delineated in the middle 1950's by the St. Joseph Lead Company during the Company's intensive exploration program to discover new lead orebodies to replace the declining reserves of the famous Southeast Missouri Lead Belt. An airborne magnetometer survey was run by the U.S. Geological Survey, the Missouri Survey and several mining companies, (of which St. Joseph Lead Company was the principal supporter). The survey was published in 1950 and disclosed an anomaly in the vicinity of Pea Ridge. In 1950 test drill holes disclosed that under some 1300 feet of sediments there did exist an iron deposit of probable commercial significance. No further action was taken until 1956 when additional drill holes confirmed beyond reasonable-doubt-that this was a major iron ore discovery.

Jan 1, 1965

The Malvern Hills coal project is now in an advanced stage of development with the stripping of overburden from above former underground workings in which a 3 m seam of subbituminous C coal with very low ash and sulphur was previously mined. The main seam dips at 45¦ to the south-east, along with other adjacent potentially recoverable thinner seams, and the strike extent of past coal mining in the Malvern Hills approaches 10 km with most extraction by underground methods. Overburden and interburden is predominantly weak mudstone, with only very minor sandstone, whilst a 1 - 2 m thick veneer of Last Glaciation loess covers the area. The coal product from the present mine site will supply the local industrial market, with production planned to peak at about 20 000 tpa. Settling pond design has been based on several different approaches, including an estimate of likely inflows from the contributing catchment of about 5 ha under predicted storms having a ten year recurrence interval. A pond of about 1000 m2 in area has been constructed with its invert in mudstone bedrock, and soil slopes have been lined with lime-stabilised clayey loess silt incorporating a gravel armour layer. The pond outflow takes place via a 2 m high 1.8 m diameter concrete dewatering tower, with a skimmer arrangement to lower the pond by approximately 500 mm between storm events. The overflow water discharges to the main stream above a natural wetland, which will act as a secondary polishing pond, and this is to be enhanced in conjunction with the neighbouring forestry company. Discharge consents specify turbidity and pH as the controlling criteria, and both will be monitored at the settling pond discharge point as well as at the entry to the main stream. Investigations to date indicate that the pH of water exiting from previous underground workings is in the range 6.8 to 7.2, and that acidic drainage will not be an issue with this mine site. No dispersive clays have been identified in assessing the overburden and batter materials, although erosion during storm events is expected and all drains will ultimately be routed through the main settling pond to ensure adequate control of runoff-generated sediment. Reestablishment of vegetation on cut and fill batters remains a priority, and ongoing monitoring will ensure satisfactory long-term performance of the pond system.

Jan 1, 2003

By J F. Seale

The design of the settling pond for the Malvern Hills opencast coal project was based on a primary requirement to control runoff and sediment generated from the immediate 6 ha mine catchment, which included two seepages from old underground workings. The pond has been particularly effective in controlling turbidity in the outflow water, with the consent limit of 50 NTU being met on all but one occasion and normal levels of discharge less than 10 NTU. Water quality testing carried out at the time of consenting indicated that there were no acid-generation issues with the proposed mine site in dominant mudstone strata of the Broken River Formation, and that water from the old mine workings was near-neutral in terms of pH and well-buffered. However, it became apparent over the very dry summer of 2003 - 2004 that slaking of the exposed mudrocks in the mine batters was resulting in significant acidity generation, and outflow pH levels were well below the consent limit of 6.5 during and following periods of rainfall. Although these acidity problems have been remediated in the short-term by the use of lime products, it is clear that a programme of lithotype characterisation for AMD should have been undertaken and this has now been implemented. Design of long-term acid drainage control measures is being carried out, and will probably be based around the use of hydrated lime for pH control with enhancement of natural wetlands.

Jan 1, 2004

By T. Kalliomäki, A. T. Aji, M. Lundström, J. Aromaa

The settling properties of anode slime in copper electrorefining have crucial effect on copper cathode quality. Anode slime settling is affected by electrolyte composition and temperature, electrolyte circulation, and the sizes and density of the slime particles and agglomerates. Typically, the industrial copper electrolytes contain 40–60 g/dm3 Cu2+, 130–220 g/dm3 H2SO4, 0.04–25 g/dm3 Ni2+, 0.005–30 g/dm3 As, and have operating temperature of 55–70°C. In optimal electrorefining process, the settling rate of anode slime is sufficiently high to avoid the risk of getting the slime entrapped in copper cathodes. In this research the settling properties of copper electrorefining bottom slimes, mainly consisting of Cu, Ni, Ag, Se, Pb, As, Bi, Sb and Ba compounds, were studied by settling rate tests. The tests were conducted in water and synthetic electrolytes with known viscosities and densities. In addition, the effect of agglomeration was taken into account – it was observed that breaking the agglomerates which existed in the as-received slimes decreased the particle sizes on average 56–73%, which decreased the settling rate. The results of this study provide detailed information of anode slime settling and thus clarify the conditions causing cathode contamination risks in copper electrorefining. INTRODUCTION Settling rates of Cu-ER anode slimes affect the purity of cathode copper and faster settling rate decreases the contamination risk (Davenport et al., 2002; Shi & Ye, 2013). The settling rates are affected by the properties of anode slime particles (Wills & Napier-Munn, 2011; Aaltonen, 2014; Kiviluoma, Aaltonen, Aromaa, Lundström & Forsén, 2016) as well as viscosity and density of the electrolyte (Davenport, King, Schlesinger, Biswas, & Robinson, 2002; Shi & Ye, 2013). Thus, it is crucial to find out how the viscosity and density affect the settling rates. Small spherical particles with diameter below approximately 50 µm obey Stokes’ law (Equation 1) (Wills & Napier-Munn, 2011). v = gd 2 (ρS – ρF) (18η) -1 (1) where v is terminal velocity (m/s), g acceleration due to gravity (m/s2), d diameter of particle (m), ρS density of particle (kg/m3), ρF density of fluid (kg/m3), and η dynamic viscosity (Pa∙s). The approximate effects of kinematic viscosity (ν = η / ρS), density (ρS) and particle sizes on settling rates defined for small anode slime particles based on Stokes’ law are presented in Figure 1. However, Stokes’ law does not take into account other than spherical shapes, and it is only applicable for small particles. Consequently, the real settling rates of the particles are lower than these (Wills & Napier-Munn, 2011). Moreover, some of the anode slime particles are larger than 50 µm (Aaltonen, 2014).

Jan 1, 2019

Hindered settling devices (teeter bed, up-current) are widely used in the mining industry to classify mineral streams into various size fractions and to separate minerals. In the coal industry these devices are extremely successful in separating coal of low densities from shale and pyrite. In the beach sand and in the iron ore industry, this equipment is used to beneficiate minerals either as stand alone units or lately as classifiers in spiral circuits. The challenge that these applications give to metallurgists is to be able to simulate the equipment by using mathematical models with or without the aid of small bench scale tests. In any green fields and many brownfields projects, limited amounts of samples make pilot plant tests difficult. Although there are mathematical approaches available, the accuracy is of such a nature that it can not be used for design purposes. This refers to the use of StrokeÆs law, NewtonÆs and the so called intermediate law as is widely published. Research done by the author indicates that in most applications none of the above laws apply. Using the original data as published by Perry and Chilton (Chemical Engineering Handbook, pp 5-64, 1973) and re-plotting it indicates that the settling velocity of particles is a function of (particle diameter)n where n varies between 1.2 and 1.6 which is different from that predicted by the intermediate law that suggests that n = 1.18. Another way of describing the relationship between the drag force and the Reynolds number is done by iterating between settling velocity and the Reynolds number. This needs more computer time but the accuracy obtained from this does add value to simulations. A small but simple test is suggested to determine the settling velocity of particles to enable metallurgists to determine variations from the theoretical calculations to determine the influence of viscosity and particle shape.

Jan 1, 2008

By A. K. Majumder

Particle motion in fluids is a subject of considerable practical importance to engineers working in fields such as hydraulics, river mechanics, chemical engineering and mineral processing. Many mathematical models have been proposed to predict the terminal settling velocities of particles in a fluid medium. The selection of an appropriate mathematical model has, therefore, become a challenging task for practicing engineers. This paper reports on an attempt to identify some of the useful models found in the literature for predicting particle-settling velocities in a fluid under free- and hindered-settling conditions. From this study, it was concluded that there is no well-accepted model validated by experimental data available for predicting particle hindered-settling velocities in a suspension of polydisperse and polydens particles. Collective efforts should, therefore, be made towards developing a hindered-settling model, as this is an absolute prerequisite for many model structures in mineral processing and other engineering disciplines.

Jan 1, 2007

By Arvindh Gupta

BC Hydro proposed to improve the stability of the existing Seven Mile Dam with 54 corrosion protected, re-stressable anchors comprising 92/0.6? strands each, in phase 2 of the program. Being globally the largest capacity anchors ever build, coupled with extra ordinary specifications, the project was a challenge for the entire post tensioning industry. The paper discusses the challenges associated with the anchor material supply as per specifications, extensive research and development carried out by Con-Tech Systems ltd. to overcome the challenges and contribute in making the project a success. The substance of this article is published in the Aug/Sep issue of ADSC magazine.

Jan 1, 2004

In the seven years that have elapsed since the AIME World Symposium on Mining and Metallurgy of Lead and Zinc, there have been a number of significant milling innovations and trends implemented in lead-zinc flowsheets to either improve grade and recovery or to control escalating mill costs. First, mill controls and instrumentation, which only had a foot in the door in 1970, have become increasingly common. In Australia, research into automatic crushing control has been implemented by Mount Isa Mines, and in virtually any large lead-zinc mill worldwide, an assortment of on-stream x-ray analyzers, grinding circuit controls, level detection devices, and reagent metering methods can be found. The increased circuit control offered to mill operators by this new technology points to more efficient flowsheets, as well as to a greater dependence upon computer-controlled operation.

Jan 11, 1977

By Michael R. McPhie

Topics of Discussion 1. The Global Mining Initiative (GMI) and MMSD North America (Brief) 2. Task 2 of MMSD North America ? A Test for Sustainability 3. The Seven Questions and their Application 4. Key Recommendations and Next Steps GMI = Global Mining Initiative Significant international collaborative effort supported by more than 30 of the world?s largest mining/minerals firms which sought to involve all communities of interest. Three major streams of activities: 1. Mining, Minerals and Sustainable Development Project (MMSD) ? 4 regional Process (North America, Southern Africa, South America, Australia) 2. Creation of ICMM (formerly ICME) 3. Major conference in Toronto in May, 2002

May 1, 2002