Search Documents

By Stewart, J. B.

THE property at which this work was done consists of a large deposit of potash salts occurring in massive beds of rock salt, overlain by 600 ft. of salt-impregnated shales and marls. It is in the Province of Cataluiia, Spain, about 45 miles from the railway station of Mauresa and about a mile south of Suria. In addition to sinking the shaft, the program of construction work laid out by the European owners (not Spaniards) included a single-track narrow-gage railroad from Mauresa to the mine; one large office building and several large shop buildings, all of brick and concrete with steel truss roofs; two extensive benches for the future recovery plant; and a large village of stone dwellings for employees. The pay-roll showed approximately 1200 to 1500 men employed. After two years' operation, ending early in the autumn of 1920, the shaft had been sunk 325 ft. and still had an equal distance to go to reach the potash; all tunnels for the railroad were done and the road-bed $0 per cent completed; only a little more than the foundations were completed for all the large buildings, and the excavations of the benches were about 75 per cent done-while only a fair start had been made upon the employees' village. This was the state of affairs when the European owners decided to offer this property under a one-year option to an American syndicate, providing that they agreed to carry on the entire building program and to sink the shaft as fast as was consistent with the quality of work which they demanded, for they wished the shaft to endure at least 200 years.

Jan 1, 1926

By J. B. STEWART

T HE position of each hole of any series of holes was carefully located by the surveyor, plotted in plan and elevation, and numbers assigned to them. The second series was staggered halfway between the first and so on for each succeeding series. Two and a, half to three months was frequently required to grout a series of holes calculated to insure safety for sinking a distance of 10 meters or say 33 ft. Naturally the initial operation called for drilling and grouting two series of holes but thereafter each sinking campaign required only one series of holes as shown in Fig. 8. The pump handling about 75 gal. per minute corresponds to 46 tons of grout or 6 tons cement delivered as a fair over-all average for the 24 hours. Thus 600 to 800 tons of cement was used for a single section of 33 ft. depth of shaft. One campaign used nearly 1100 tons of cement. Some holes were effectually sealed with as low as 30 tons, while many required 60, and some 80 to 90 tons.

Jan 1, 1926

By Norman Braly

THE following is not offered as an extended paper on the subject of shaft sinking, but more as a description of the present practice of shaft sinking in the Butte district. The Anaconda company is sinking at present the following shafts: Badger State, Moose, Mountain Consolidated, Mountain View, Pennsyl-ania and Tropic. At the High Ore and Leonard mines the shafts are being deepened by sinking two compartments and will subsequently be enlarged to the full working size by raising alongside the compartments which are now being sunk. The following other companies are also sinking shafts: Butte-Alex Scott, Butte and Zenith City, Boston and Corbin, North Butte Mining Co. (at the Granite Mountain shaft), East Butte Co. (at the Pittsmont shaft), and the Rainbow Lode Development Co. Shaft Timbering. The shafts of the Butte district, generally speaking, are of three compartments arranged in a straight line, and the pump compartment is usually arranged for the use of an auxiliary hoisting cage, as well as for carrying pipe lines and electric wires. The Rainbow shaft is practically square, and of three compartments. The length of the shafts outside of timber will vary from 17 to 22 ft., and the width from 6 ft. 6 in. to 7 ft. Fir timber is used in all shaft work. This may be obtained from the Coast, when it is known as Coast fir, or from Idaho or Montana, when it is known as native fir. The native fir seems to be the tougher wood, but it is hard to obtain clear lumber in the lengths and sizes necessary for shaft work. Some of the shaft timber of the Anaconda company has been treated with creosote as a preservative, but this practice has not come into general use, as the ground of the camp is so heavy that the timbers usually crush before they rot. The size of timber most .used for shaft work is 12 by 12 in., while 10 by 12 in., 10 by 14 in. and 12 by 14 in. are used for some of the special pieces around the shaft. The new Leonard shaft is timbered with 14 by 14 in. wall plates throughout.

Jan 8, 1913

Discussion of the paper of Norman B. Braly, presented at the Butte meeting, August, 1913, and printed in Bulletin No. 80, August, 1913, pp. 1881 to 1906. GEORGE A. PACKARD, Butte, Mont.:-I would like to ask Mr. Braly if he has any information as to the relative efficiency of the sinking pump, using it as he refers to it, discharging the exhaust into the water column or otherwise. MR. BRALY :-I have never gathered any information on that point. It is a question of getting the work done. In driving the shaft, using that method, we find it easier on the men and everything else. In the bottom of the shaft, if you exhaust back into your column, it is a quiet. shaft. Another thing is the freezing: if you are sinking with air in your pump, you will find it is liable to freeze, and in that case as the air is still under compression it will not freeze the pump. The difference is very small if there is any. But, as might be expected, the pump is a little less efficient when exhausting the air into the column. MR. PACKARD :-I suppose all of us know what a pump in the bottom of the shaft is. My experience has been, although I have no figures, that the capacity of a pump is quite considerably decreased if you are pumping, say, from a depth of 200 ft. through a No. 7 Knowles pump, when you exhaust the air into a column, but, on the other hand, it is also my impression that we can raise the water to a little greater distance. I would like to get some figures from somebody who has made actual tests.

Jan 11, 1913

By J. Murray Riddell, George A. Morrison

THIS paper is a companion to the one by George A. Morrison on Mining a Deep Limestone Mine in Ohio.[+] Barberton is 8 miles west of Akron, Ohio, and 23 miles south of Cleveland. The underground mining of limestone at Barberton constitutes the world's deepest limestone mine. The stratigraphy is as follows: 0-20 ft. Loam, clay, sand and gravel. Water bearing. 20-40 ft. Fractured. sandstone. Water bearing. 40-110 ft. Sandstone with interbedded shale, slightly fractured. Water bearing. 110-314 ft. Sandstone with interbedded shale, slightly fractured. Water carrying. 314-2197 ft. Shale with occasional seams of sandstone, which varies in thickness from a few inches to 4 feet. Dry. 2197-2247 ft. Limestone. Dry. 2247-2742 ft. Dolomitic limestone. Dry. 2742-2767 ft. Salt. Dry. 2767- Dolomitic limestone. Dry. All of the strata dip to the southeast, about 0.5 per cent from the horizontal. The top 110 ft. of the crust is water-bearing. The rock strata are naturally fractured to a depth of 314 ft., sufficient to allow the passage of water. In the shaft-sinking operations, a stra was encountered at a depth of 520 ft., and flows of methane gas were pierced at depths of 1350 and 1952 feet. Specifications for the mine plant called for, in part, the sinking of two vertical shafts and a hoisting plant capable of producing at the rate of 300 tons per hour. No. I shaft is 550 ft. west of No. 2 shaft. Each shaft measures 8 by 17 ft. outside of steel. General features of the design (Fig. I) are: Principal set members, 6-in. H-section; connecting angles (studdles), 3/8 by 4 by 4-in. angle irons; spacing of sets, 8 ft. centers; spacing of bearer sets, generally, 160 ft.; bearers, of 12-in. I-beams. Each bearing set featured a concrete ring about the periphery of the shaft, steel to rock, and 8 ft. in height; permanent guides, 6 by 10-in. long-leaf yellow pine, 85 per cent heart. THE SHAFT-SINKING OPERATION The preliminary shaft-sinking work consisted of driving interlocked steel piling about the exterior of the shafts to depths of 35 and 32 ft., respectively, and of such horizontal dimensions as to ultimately permit the pouring of a concrete collar 2 ft. in horizontal thickness. Following the pouring of a shaft collar, a temporary wooden headframe for shaft-sinking purposes was erected. The head-frame, while ordinary, featured: (I) a storage pocket of 300 cu. ft. capacity with truck servicing facilities, and (2) pneumatically operated dump doors, which were actuated by the hoistman, thus caring for the dumping of the "ball-and-chain"

Jan 1, 1944

By R. J. A. Fricker

IT is the purpose of this essay to give a reasonably complete description of shaft sinking under a rock pentice in a small Northern Ontario gold property. Hallnor is in many ways an exceptional mine, but the sinking operations here described are but typical examples of the excellent practice for which Canadian mines and mining engineers are justly famous the world over. The worth of the subject lies, therefore, nor in its originality, but in its soundness; not in the spectacular, but in the economical and safe. Attention is particularly drawn to the excellent safety record and to the exceptionally low overall sinking cost. INTRODUCTION Prior to April, 1939, the Hallnor No. 1 shaft had been sunk vertically to a depth of 997 feet below the surface. It is a three-compartment shaft, 19 ft. 10 in. by 7ft. 7 in. outside the timbers (see Figure 1).

Jan 1, 1941

By J. Fred, Johnson

THIS TALK is a digest of some of the information contained in tables, one on practices and one on costs of shaft sinking, in Bulletin 357 of the U. S. Bureau of Mines written by E. D. Gardner, Supervising Engineer of the Bureau at Tucson, and myself. The table of practices contains information on 43 shafts and the table of costs contains information on 25 shafts. These various shafts were sunk between 1917 and 1930 so they may be termed modern practice with costs applicable in the United States, Canada and Mexico. In the compilation of this material the statistics on shafts which were concreted have been eliminated, as these figures were entirely out of line with corresponding figures for timbered shafts. It is my experience that where costs are divided between sinking and concreting the tendency is to load the costs onto the larger item of concreting. Thus a shifting of costs making an addition of 10 per cent in concreting costs may suffice to make a deduction of 40 per cent in sinking costs. Fine work is done (on the books) and everybody is happy. Most shafts are sunk with three shifts of men per day. Each shift consists of men who are miners, muckers, or timbermen, as chance may call for during their shift. Where pumping or high fixed costs do not necessitate three shifts it is cheaper to sink on two shifts. It is desirable for speed and economy in any case to work out a cycle of operations for each 24 hours. In this way men are hired for their ability as machinemen, muckers, or timbermen; they know exactly what to do and there is no passing the buck to the next shift.

Jan 1, 1933

By Sastry Putcha, Santosh Mummaneni, Avasarala Swamy

"Inspection of bored pile hole bottom prior to placement of concrete is one of the most crucial element of foundation design and construction, especially for end bearing piles. Pile hole bottoms that are not cleaned well for sediments could potentially result in settlement. Although many projects have specifications in-place for drilled pile hole inspection, they are rarely implemented as the current available tools are either unsafe or cumbersome and costly, thus making it very unattractive for owners and contractors. Further, sometimes the post-construction nondestructive quality control testing such as PIT or sonic logging on piles resulted in unanswered questions related to soft bottom. This generates costly disputes with additional testing including concrete coring and possible repairs. Currently, there are several bored pile bottom inspection devices in USA, namely, SID, DID, and SQUID which can either provide video and photo documentation or measure sediments.“ShaftCam”, a patented advanced Digital Borescope, was invented to address the issues related to pile hole bottom inspection with its ability to measure sediments as well as photo and video documentation. Shaftcam device consists of 8-inch diameter bell with a camera, led lights, air hose connection and penetrometer with digital measurement that are connected to a control power box and laptop through a cable. The bell is fitted with a round clear open fiberglass skirt to form an open chamber. A simple motorized winch frame allows the user to lower the ShaftCam equipment gently to the bottom of the shaft at the desired location. Once the bell with camera is lowered to the bottom of the hole, air is pumped into the clear chamber to displace the water/slurry/polymer and get a clear view of the hole bottom to record the conditions and measure the sediment thickness and resistance. The skirt can also be enclosed and lowered to the desired location to allow for inspection of shaft walls.ShaftCam weighs less than 15 lbs. (6.8 kgs) in water and allows for inspection of the hole by one person in less than 30 minutes. Use of ShaftCam has saved significant time and money and thus allowed owners and contractors to readily accept and implement the quality control measures in many projects in USA over past few years."

Jan 1, 1900

By William C. Paschen

Damen Avenue to Roosevelt Road, the Tunnel and Reservoir Plan (TARP), a Deep Tunnel Project for the Metropolitan Sanitary District of Greater Chicago consists of 25,189 lin. ft. of 32 ft. tunnel with 1 ft. 0 in. concrete liner throughout. The 17,100 ft. main tunnel connects at both ends with two other Deep Tunnel contracts. A branch tunnel connecting to the mainstream tunnel, commences approximately 4,140 ft. from the construction shaft and runs 8,089 ft. south and terminates at the Racine Avenue Pumping Station. Shaft work consists of one 28 ft. 6 in. diameter construction shaft, one 3 ft. 6 in. diameter access shaft and 25 drop shafts-four of which have vent shafts. The drop shafts vary in diameter from 4 ft. 0 in. to 17 ft. 0 in. All shafts vary in depth to invert from 225 ft. to 235 ft. Work has been underway for 16 months and as of this writing the construction shaft and access shaft are complete. Seven shafts have been excavated and concreting operations have started in four of them. The starter tunnel is complete, the mining machine has mined 250 lin. ft. and the muck removal system is in full operation. The contractor for the project is a joint venture of Paschen/Morrison-Knudsen/Kenny. Paschen Contractors, Inc., Chicago, Illinois is the sponsor. The total contract amount is $107,837,300.00.

Jan 1, 1979

By C. E. McWhorter

IN underground mining recent trends toward mining large tonnages of low-grade ore have created, among other things, a need for cheaper and more flexible ore transport. A relatively new development has been the adaptation of shaker conveyors to meet this need. Although widely used in coal mining, only in the last few years have shaker conveyors been used in underground metal mining. The equipment consists of a driving engine, either electric or air powered, upon which is mounted a drive trough supported in ball-bearing frames. The trough line, or conveying medium, is made up of a number of sections, each section connected to another, usually with bolts. The length of each trough section is controlled by the length that can best be handled underground, but is usually from 9 to 13 ft over-all. The length of a complete conveyor line is determined by the character and weight of material to be handled as well as by the size of the ore body. Trough lines vary in lengths from 100 to 300 ft and the trough has a cross-section area of 127 sq in., and is 22 in. wide by 6 ½ in. deep.

Jan 1, 1948

By R. D. Satterley

THE Sherwood mine is an iron-ore mine owned and operated by the Inland Steel Co. in the Iron River district of the Menominee Range in Michigan. The property consists of an 80-acre tract in the village of Mineral Hills, about a mile north of the city of Iron River. The ore mined is a reddish brown, nonbessemer hematite and limonite. The ore bodies lie in a large syncline having an east-west strike and are associated with a rock structure that is folded in a complex manner. The two 40-acre tracts run north and south and the shaft is at about the center of the north forty. The shaft is 1286 ft. deep, with the principal operating level at a depth of 1000 ft. from surface. A new level at a depth of 1200 ft. is in process of development. The ore body at the 1000 ft. level is east and west at approximately the line between the north and south forties and at this elevation is from 50 to 250 ft. wide and extends above the level at varying heights of from 50 to 250 feet. The 1000-ft. haulage drift extends south from the shaft, through the east-west ore body to the slates on the south side of the body. The ore body was intercepted in the drifting at about 800 ft. from the shaft and was about 200 ft. wide at that point. A crosscut was extended to the east and west property lines along the south boundary of the ore body. This east-west ore body is laid out in areas 80 ft. wide for stoping with pillars 40 ft. wide. With this plan a stope is approximately 80 by 200 ft. and has a pillar on both sides that is approximately 40 by 200 ft. The ore has a height of from 50 to 250 ft. above the elevation of the level, therefore the height of the stopes varies in accordance with the height of the ore body at each location. From the crosscut, two main raises, each 6 by 7 ft., are put up into each 80 ft. stope area (Fig. I). One of the main raises serves as a manway and the other as an ore raise, through which the ore is transferred from the stope to the tramming equipment. The original layout was for scraping of the ore from under the stopes into the ore raises. The ore raise is put halfway (east and west) along the 80-ft. stope area and usually is in iron formation. The manway and ore raise are on approximately 15-ft- centers. These main raises are put up to a height of from 22 to 30 ft. above the level floor, then from the top of the ore raise a scraper drift (8 X 8 ft.) is driven across the width of the ore body, which is in the neighborhood of 200 ft. From the scraper drift, mill raises are put up at 12 ½ -ft. centers, staggered on opposite sides of the drift, and these are extended 23 ft. above the elevation of the scraper-drift floor. The sublevel connecting the top of these mill raises is called a mill "sub." Other sublevels are developed parallel to the scraper and mill subs at 25-ft. vertical intervals above the mill sub. The mill sub and the other subs above the mill sub are known as sublevels or dog drifts, and are 4 ft. wide and 6 ft. high. These dog drifts

Jan 1, 1945

By F. V. Hicks

THE similarity of mining practices in bituminous coal fields through-out America is due to the fact that certain fundamental conditions are encountered in all fields. The problems of labor, housing and mining are somewhat similar whether the mine is in Pennsylvania, Illinois, Wyoming or the State of Washington. Each field has had its particular problems, resulting in advantages or disadvantages over a competing field. This might take the form of a wage differential, a better natural condition more favorable to cheap production, or proximity to a market that allows freight rate advantages, etc. In any event, no matter how favorably situated, the mining companies that have been slow to recog-nize and accept the advantage of mechanization, clinging too long to the old hand methods, have found themselves unable to meet competition. Throughout the Wyoming coal fields, production methods have so changed in the last decade as to be almost unrecognizable to an old-time coal miner who has had no connection with the industry during; that period. The old contract system, with its peculiar labor relationship between employer and employee, based upon the long-established custom that the miner's working place was his castle, and that it was his privilege to carry on operations within that place largely in his own way and to his own liking, is a condition that has passed away. The present-day, 100 per cent mechanized mine bears but little resemblance to the old. A change -in system has naturally altered the old-time labor relationship. Contract labor has been almost entirely eliminated and a straight day-wage basis established, with certain classes of work calling for different rates, which places the entire personnel of the underground operating force more directly under the direction and supervision of the mine foreman and his assistants. The transition from the old order to the new has gradually done away with the system of penalties, personal- rights and privileges existing under the contract system, which were so controversial in the past that the average mine management was constantly involved in labor disputes in fields where organized labor was employed.

Jan 1, 1936

By P. Bevilacqua, G. Ferrara, M. C. Williams, T. P. Meloy

Tabling is an old environmentally friendly separation unit operation. This paper models shaking tables and explores the action and design of riffles on shaking tables. By reassessing riffle shape and riffle patterns, significant improvements in tabling performance appear feasible. While table sales appear at their nadir, a high-tech environmentally friendly table may have a significant market in the coming decade. Riffles on a shaking table impact particle separation. Particles are affected by riffles and their exit position on the table is dramatically changed, Riffle shape determines how much the riffle will influence a given material. Moreover, riffle patterns influence the concentration of a given material and its exit points on a table. This effect of riffle placement and design is modeled in a spreadsheet. Major performance and separation improvements may he expected by improved table design. Two physical laws of tabling have been derived. These laws aid in the design of sophisticated high-tech tables.

Jan 1, 1995

By T. P. Meloy

Riffles on a shaking table have a major effect on particle separation. This effect is modeled in a spreadsheet.

Jan 1, 1993

By Mick Fritz, Ryan Gilmore

The Center for Disease Control [CDC] is in the midst of a twenty year project, part of which includes demolishing existing buildings and erecting taller, more modern structures within the same foundation foot print. Controlled Blasting Inc, a large and experienced construction drilling and blasting company in Metro Atlanta, was contracted to provide the drilling and blasting for the new building foundations. Working on a construction site, in this type of environment, creates many challenges for the drilling and blasting crews.

Jan 1, 2008

By J. A. Smith

The topic assigned me by the Chairman of the Institute, "Safety Practices in Franklin and Williamson Counties, Illinois," I fear will necessarily resolve itself into a paper on shale dust, its application and the results obtained. I returned .only last week from a three weeks trip through these counties at which time, through the courtesy extended me by the operators, I had ample opportunity to visit and inspect many of the largest mines in the field, some of which are among the largest in the United States. With the exception of shale dust and ventilation, I see but vary few instances where the Illinois mines are further advanced in safety precautions than the western mines, and in some respects I believe the operators of the West are further advanced in safety methods than their eastern brothers. Great care is exercised in handling of all ventilation currents. This is an aboslute necessity, as this field is quite gaseous, and the peculiar geological structure of the overlying and underlying strata makes airtight seals very

Jan 1, 1924

"Ground control research in underground coal mines has been ongoing for over 50 years. One of the most problematic issues in underground coal mines is roof failures associated with weak shale. This paper will present a historical narrative on the research the National Institute for Occupational Safety and Health has conducted in relation to rock mechanics and shale. This paper begins by first discussing how shale is classified in relation to coal mining. Characterizing and planning for weak roof sequences is an important step in developing an engineering solution to prevent roof failures. Next, the failure mechanics associated with the weak characteristics of shale will be discussed. Understanding these failure mechanics also aids in applying the correct engineering solutions. The various solutions that have been implemented in the underground coal mining industry to control the different modes of failure will be summarized. Finally, a discussion on current and future research relating to rock mechanics and shale is presented. The overall goal of the paper is to share the collective ground control experience of controlling roof structures dominated by shale rock in underground coal mining.INTRODUCTIONThe National Institute for Occupational Safety and Health’s (NIOSH) Office of Mine Safety and Health Research (OMSHR), formerly the United States Bureau of Mines, has been conducting research on ground control safety for over 50 years. The overall objective of the research is to reduce underground mining injuries and fatalities by characterizing roof conditions, improving roof support performance and application, and optimizing pillar design and mine layout. Underground mining has one of the highest fatal injury rates of any industry in the United States—more than five times the national average compared to other industries (CDC, 2012). Roof fall injuries can be severe, resulting in lacerations, bone fractures, amputations, and death. Non-injury roof falls can also be problematic, resulting in lost production, delays, blockage of primary escape routes, disruption to ventilation, and hazardous rehabilitation conditions.Coal mining is increasingly subject to more adverse geological conditions. Weak roof can be found in all coal mining regions in the United States, but there are a few geographically isolated areas with higher roof fall rates contributed to by particularly poor roof conditions, as represented in Figure 1. This figure shows that when non-injury roof fall rates are normalized to production, the Illinois Basin and Central/Northern Appalachia regions have the highest rates. These isolated regions have inherently weak roof even before mining has occurred, and this roof is easily damaged during the mining process. The weak roof in these regions consists primarily of shale. Shale can be troublesome in underground coal mining because it can appear massive but easily splits along bedding planes and is often moisture-sensitive."

Jan 1, 2015

By Peter Zhang, Daniel Su, Mark Van Dyke, Heather Dougherty

The integrity of shale gas wells in longwall chain pillars under the influence of longwall mining is a safety concern for both coal and gas operators. Previous modeling studies of gas wells in longwall pillars have shown that a FLAC3D model can predict longwall-induced stresses and deformations in gas well casings with reasonable accuracy. The predicted casing deformations can be verified by multi-finger caliper survey. This study concerns the influence of longwall mining on eight shale gas wells in a shale gas well pad located in the chain pillars between two adjacent longwall panels under 1,030 feet of cover. FLAC3D modeling was performed to predict longwall-induced deformations in gas well casings based on site-specific mining and geological conditions. Small deformations less than 0.5 in were predicted in the intermediate casing above 600 ft depth, and very small casing deformations less than 0.15 in were predicted below 600 ft due to high abutment pressure and high frictional resistance along the weak bedding interfaces. After the first panel was mined, a 56-arm caliper survey was performed on one of the wells to measure the longwall-induced casing deformations in the intermediate casing. The predicted casing deformations were then compared with the measured deformations, which indicated that the prediction was generally in good agreement with the measurement in terms of deformation locations and magnitudes. Findings from this study provide valuable information not only for stability assessment of shale gas wells in longwall chain pillars but also for developing engineering guidelines to preserve casing integrity through adequate pillar and casing design.

By D. Moronkeji, R. Maharidge, D. A. Curry, B. J. Davis, U. Prasad, J. Franquet

"Proper shale characterization is crucial in shale gas drilling, exploration, completion and production. Unlike porous sandstone and carbonate reservoirs, the challenge with shales comes from their micro- to nano-darcy permeability ranges and the anisotropy of their mechanical and hydraulic properties. Most porosity-dependent logs are not sensitive enough to capture the true behavior of shales. Consequently, mineralogy and other strength and stiffness-related properties must be determined to characterize magnitudes and variances in shale mechanical and flow properties. In addition, these properties must pass quality assurance/quality control (QA/QC) practices to give confidence in their use in subsequent log calibrations, during geomechanical modeling, or in fracture design models. This paper presents a technique to integrate shale properties that are measured by various methods, and a methodology to perform QA/QC on the data before application.Shale properties originate from various sources, including downhole and laboratory measurements. Physical samples for laboratory testing are usually limited to a few depths. Lab tests are often costly, and replicating in-situ conditions can be difficult or impossible. In addition, results frequently show wide scatter, reflecting inherent depth variability and lateral heterogeneity. Wireline logs provide nearcontinuous data, but rarely yield direct measurements of rock strength properties. Although geomechanical and fracture models use log data, calibrating it with reliable and previously verified lab-measured properties is important. This paper presents a process to perform QA/QC on lab-measured data using various crossplots.Ten mechanical, microstructural and physical properties are graphically displayed to visually characterize shale strength behavior in ambient and in-situ conditions, whether measured or modeled statically or dynamically. These properties are often sourced from different departments. The properties are integrated but are individually subject to the previously mentioned uncertainties. Pairs of property values are crossplotted and compared with correlations from the literature or previously established with qualified data from related formations. Conformance with these correlations gives confidence in the data, whereas outliers are flagged as questionable. Repeating the process with questionable data crossplotted against other parameters for the same depth highlights the property with the greatest uncertainty. The determination of its value is investigated to locate the source of the inconsistency and establish a more reliable value. Where this is not possible, the user has a rational basis for rejecting that property value."

Jan 1, 2015

By J. B. NEALEY

THE common method of shale mining, drilling, shooting and steam-shovel loading, is fast giving place to a comparatively new method which is purely mechanical. This machine is known as the shale planer and takes a cut from a very large face, 50 ft. or more in height. As shale deposits are usually stratified, the quality varying with the stratification, a very uniform product is obtained with this planer, for its "cut" is across the entire face, vertically. This planer was designed and built some 15 years ago by J. M. Powell, president of the Indiana Drain Tile Co., Brooklyn, Ind. Unevenness in mixing the material from the different layers in the shale deposit of this company was causing considerable fluctuation in the firing- shrinkage and color of the ware produced, thus lowering the quality. Some method of maintaining a uniform proportion was vital and this planer was therefore devised. Its capacity was approximately 175 tons daily: cut, mixed and loaded.

Jan 1, 1929