Search Documents

By V. G. Matziaris

The differentiation between saturated and un-saturated soils becomes necessary due to basic differences in their nature and engineering behavior. The most important difference is the existence of a suction zone, above the water table, in unsaturated soils. Pore water pressure in this zone is always negative and the shear strength is greater than the one in saturated soils. This is due to an occasional and apparent component in the Mohr-Coulomb equation, which appears in unsaturated soils. In slope stability analysis of unsaturated soils, the factor of safety increases due to this occasional cohesion component of the shear strength. However, the suction zone tends to disappear because of rainfall. In these cases the factor of safety decreases and eventually the slope may fail. In this article, a parametric study of the effect of suction zone fluctuation due to precipitation in slope stability is examined. For this purpose a Combined Hydrology and Stability Model (CHASM) has been applied.

Jan 1, 2005

By I. J. A. Brackley

An investigation of the slope stability of a pit and failures of spoil dumps, carried out at Silicon Smelters quartz mine, Pietersburg, South Africa, is described. The major geological feature of the mine is the intensely foliated schist in the footwall, with exceptionally Iow strengths upon extensive discontinuities, and the similarly unusual strength properties of the dumped schist spoil. The selection of slope angles for the pit is described, and a proposal for the stabilization of the failing spoil dump by segregated dumping is explained.

Jan 1, 1985

By Jose M. S. Ramos

This paper describes the slope stabilization procedure at Cauê Mine, Companhia Vale do Rio Doce - CVRD, Itabira, State of Minas Gerais, Brazil. Cauê Mine, is a large open pit, to produce about 41 million tons of iron ore during 1974, and an intensive program of investiga Lion was carried out to provide the basic data for stabilizing its slopes, The ultimate rock slope in the W area will be about 400 m high with dipping angles decreasing gradually from top to bottom of the pit. The investigations started in 1969 and since then many geologists and engineers, from both CVRD and Geotécnica S/A., assisted by international consultants, have given their contribution to the achievement of solutions. It is hoped that this paper may contribute to the slope stability of other mines in tropical climate.

Jan 1, 1974

By J. M. Réjean Gagnon

"Quebec Cartier Mining Company is currently mining a low-grade iron ore deposit in northeastern Quebec. The Company is producing some 8,000,000 dry gross tons of concentrates per year, grading about 66 per cent iron. The pit, which is located on the keel or hinge line of a fold, will eventually be about 1,000 feet deep with a surface area of 8,000 by 2,600 feet. The most significant structural discontinuities in the mine are the natural bedding planes and secondary perpendicular joints. The exposed walls are subjected to a sub-Arctic climate and heavy blasting occurs approximately six times a month.QCM utilizes design and operating techniques to control rock fall. Steps are also being taken to analyze the ultimate over-all pit slope stability."

Jan 1, 1968

By Andre Zingano

An underground mine using room and pillar and retreat mining methods was developed during the 1950?s. In 2009 an open cast mine was opened in the same reserve with the objective of mining five coal seams including the one previously mined. Recently, a series of slope failures were detected at the open cast mine. The surface mine map was overlain on the underground mine map, and it was observed that the slope failures were located above a retreat mined area where the overburden had caved and the ground subsided. The deformation and displacement attributable to subsidence caused a loss of strength in the overburden strata. The objective of this paper is to study the causes of slope sliding (or failure) due to the ground subsidence of rock layers above oldmined out areas. A map was created to overlay the two mines -- the abandoned underground mine and the active surface mining. Two- and three-dimension numerical modeling was conducted to simulate the slope behavior and to verify whether the mine subsidence was the cause of slope instability. This study indicated that the subsided rock layers were the cause of slope instability and sliding.

Jan 1, 2013

By E. Kalhan, C. Kincal

One of the biggest problems in open pit mining is slope stability. The avoidance of slope stability problems depends on a comprehensive assessment of environmental and operational factors such as geology, climate, and mining activities. In the light of these considerations, slope geometries should be determined in accordance with engineering principles. In this research, the slope stability of rock slopes in a mine opened in a gneiss geological unit has been studied. Production activities were ceased in 2019 due to the slope movements in the eastern part of the quarry. In order to safely continue the production, field works were primarily carried out. To assess slope stability, detailed discontinuity surveys were carried out on bench faces. Subsequently, kinematic and numerical analyses were employed to identify geometries that are expected to maintain stability under the prevailing geological structures and environmental constraints. Engineering geological studies such as scanline measurements in steps and investigation of potential failure mechanisms by kinematic analysis technique were carried out. Small module reactor and Q-slope rock mass classification systems were used to evaluate slope stability. Based on these classification systems potential unstable rock slopes were identified and thematic maps were created using geographic information systems. The most suitable slope geometries are suggested for these slopes. In addition, the improvement methods suggested by the rock mass classification systems were proposed for these slopes.

Sep 1, 2025

By J. L. Workman

The stability of spoil and highwall slopes are important to successful strip mining. This paper discusses soil parameters of importance in stability analysis. The common mechanisms of spoil failure are discussed. Modes of highwall failure are also outlined. The importance of water to stability is presented. Dragline mining methods most suited to creating spoil and highwall profiles that address stability needs are provided. It is concluded that groundwater and surface runoff must be well controlled, and that it will often be necessary to modify spoil and highwall configurations to achieve a stable overall slope angle.

Jan 1, 1996

By J. Andrew Leach, Robert T. Tape, Thomas G. Harper

A practical approach to elope stability design of heap leaches up to 90 m (300 ft) high is presented based on recent experiences with heaps throughout the Western U.S. Shear strength parameters for foundations, ore and liner systems are considered, with particular attention given to frictional contacts between geomembranes and clay or geotextiles. Stability of both ore and containment dikes is discussed including the effects of seismicity, staged dike construction, progressive heap development and in-heap solution levels. Design criteria and methods of analyses are presented along with techniques for improving stability.

Jan 1, 1987

By Peter N. Calder

The orientation of planes of inherent weakness (joints) with reference to an excavation in rock is the critical factor determining stability. The purely frictional 'residual' strength remaining following the breakdown of initial cohesion is the only strength which can be counted on to resist sliding for the long term. A simple method of resolving driving and resisting forces in three dimensions along joint intersections 'undercut' by the excavation is presented. Contrary to the case of slope failure in soils, it is shown how significant changes in the slope angle sometimes have no effect on the degree of stability pre-sent in rock slopes. Wall control by reorientation of the slope, the use of cable bolts and water diversion are briefly discussed.

Jan 1, 1970

By E. Topuz, G. Faulkner, M. Karmis, C. Haycocks

The Appalachian coal region of Virginia, southern West Virginia and Kentucky and the extreme eastern portion of Tennessee constitutes a unique area of surface coal mining activities. The area contains a number of contiguously placed coal seams, up to a total of fourteen in some places, which vary in thickness from a few centimeters to 2,5 meters. Much of this coal is of high quality, some being the highest grade metallurgical coal found anywhere in the world. The region may be broadly characterized physiologically as a dissected plateau with a relief above the valley floors of up to 500 meters and a dendritic drainage pattern. Up to six seams may outcrop in the hillsides above drainage, many of which have been subjected to contour stripping operations. Prior to the passage of the surface mining reclamation act, little effort was made to reclaim stripped areas. The passage of the strip mining act, including the controversial requirement for returning the land to its approximate original contour, has forced intensive recla¬mation efforts from the mining industry. The wisdom of this original contour requirement has been the subject of considerable debate and litigation, mainly because of its cost, inconvenience, and value of the land after it has been reclaimed. Regardless of whether recla¬mation is carried out, under current practices slope failures do occur. This in effect circumvents the intent of the law and can expose large unvegetated spoil areas, and contribute to hillside erosion and stream silting. Such failures must be eliminated if further costly reclamation efforts are to be avoided.

Jan 1, 1983

By Marc C. Betournay, John E. Udd

"In this study, the authors investigated the stabilities of slopes cut predominantly into Trenton limestone in a large quarry in the Montreal region. Analyses of the bench and pit walls indicated that small-scale toppling, ravelling, and wedge failures are the most likely modes of instabilities. Because most of the joints dip steeply, however, the conclusion was made that relatively high walls could probably be justified.The field investigations were supplemented with the determinations of the shearing strengths of artificial discontinuities that were cut into samples of the limestone. The properties of a fine-grained limestone were found to be influenced very much by the magnitudes of the loads that were applied, while the properties of a crystalline limestone were found to be much less, or not load-dependent.The study is one of a number that are being conducted in this area.IntroductionExtensive quarrying has been done in the sedimentary strata of the Montreal area for a very long time. By any standards, it can be said that the Island of Montreal is a major mining area. At present, approximately 20 quarries are being operated in, or near, the city of Montreal.In addition to the millions of tons of limestone that are removed each year, a large number of excavations for foundations are cut into the sedimentary rocks.To date, however, very little information has been published concerning the engineering properties of the local geological materials. No mention is made of this aspect in the references which are presently available.Because of this lack of information, the senior author has initiated a study in which the strength properties of most of the rock types, and of the natural discontinuities contained in these, would be investigated. To date, the results of one other investigation have been published and other work is in process. It is hoped that the end result will be a comprehensive knowledge of the important strength properties of all of the rocks in the entire region."

Jan 1, 1983

By Burt Hartmann

The nation's ever-expanding construction and mining activity has placed an increasing demand upon engineers and geologists to design and construct stable slopes in earth materials-soil and rock. Man's attempt to handle these slope stability problems has been based primarily on practical experience and the resulting theories formulated to explain the phenomena. Too many instances occur when man is faced with a slope stability problem that has not yet been experienced and doesn't lend itself to solution by any existing theory. At this point he must extend himself in using his engineering judgment to arrive at a reasonable and safe design. As past experience has shown, all of the "safe designs" are not really safe. Sometimes they result in embarrassing failures. Measurements provide the key to understanding and controlling natural phenomena. We cannot hope to gain control of the slope stability problem until we understand the causes of slope failure, their behavior with respect to time and their relative magnitudes. Measurements required for an adequate definition of any slope problem must be of the highest reliability because of the importance of decisions which must be based on them. For this reason, direct measurements of movement, shear strength, water pressure, etc. of the unstable mass are preferable to indirect measurements of other physical properties. Movement instruments which can be positioned inside of the slope mass (within boreholes) are among the most useful in diagnosis and/or monitoring of slope movements. The higher the sensitivity and il-measurement precision possible with borehole instruments, the quicker the required information can be obtained and the more exactly may hazardous conditions be observed. A high density of measuring points in a single drill hole is deemed essential for diagnostic purposes. Behavior gradients may thus be obtained. The Pressure Meter (Fig. 1) can be used to measure a relative strength

Jan 1, 1968

By Trudinger JP

Mt. Newman Mining Company Pty. Ltd.3 oper ates the Mt. Whaleback iron ore mine in the Ham- ersley Iron Ore Province of Western Australia. The present rate of production of high grade hematite iron ore is 33 million tonnes per year. Mining is by open cut quarrying,with 15m high benches. The present quarry operations will be extended to a large oval pit to win over 1400 million tonnes of iron ore. The pit slopes will extend up to 500m in depth and the perimet- er of the slopes will exceed 15km. Sixty per- cent of the ore is below the water table, which presently lies 45m below the general plain level Dames & Moore, rock mechanics consultants designed the pit slopes during early mine devel- opment to ensure an economic and safe operation.

Jan 1, 1975

By M Edgar, G Pattemore, M Auad, K Job, A Job, S Gale

In recent decades, significant advances have improved the modelling techniques for predicting slope failure. Predicting failures is vital in open pit mining due to the significant risk posed to personnel and equipment from unstable pit walls. Failures not only cause harm and damage to people and equipment but also cause delays to production and subsequently increase operational costs. Coupled with improvements in modelling techniques, utilisation of advanced scanning systems, such as high-definition imagery from UAVs has enabled faster and more precise mapping and modelling. However, one key element required for accurate slope stability modelling and monitoring is the ability for mine geotechnical engineers to have an accurate understanding of the mineralogy and moisture content of slopes, in real-time. To address this challenge, research has been undertaken to utilise hyperspectral imaging across a broad spectrum, combined with high-definition imagery, and LiDAR to scan slopes for minerals and moisture content. In addition to accurately mapping mineralogy and moisture, the data must be collected autonomously and remotely to ensure ongoing safety. The results show that there are many direct and indirect benefits from this new technology, including the ability to monitor slopes at a safe distance and in real-time, improved accuracy of modelling, detection of risks, and improving the automation workflow for geotechnical engineers. The paper presents recommendations for the implementation of the technology in open cut mining environments.

Jun 22, 2022

By D J. Clark, S Hewson, T Li

Cadia Hill Pit is a gold copper porphyry deposit hosted in monzonite. The pit slope design is primarily based on structural controls related to faults and shears with largely massive rock masses between the structures. The slope design attempts to achieve an optimum configuration at a bench to overall scale, considering economics and safety implications against the geotechnical and structural conditions. To date the slopes have been mined at interramp angles of up to 60¦ over heights of 120 m. Limited slope and batter failures that have occurred are structurally controlled and occur rapidly. The pit-mining schedule requires concurrent mining of part of the final pit walls and the progressive interim cutbacks. Engineering and operational solutions to hazard reduction and risk management issues have been implemented wherever viable to æengineerÆ out the hazard and mitigate the risks. However, comprehensive management plans and operating procedures have also played a vital role. This paper details the management plan and the operating procedures that have been developed and implemented to mitigate the risks associated with rock falls.

Jan 1, 2003

By Carl D. Broadbent

The goal of slope mechanics is to achieve efficient and safe pit slopes. In the case of ultimate mine slopes the objective is to minimize the stripping ratio by steepening the slopes to their maximum stable limit. On the other hand, the inclination of working slopes is normally established by operating space requirements and the function of slope mechanics should be the continuous surveillance of slope conditions to assure long-term stability and to provide timely warning of impending slides so that corrective measures may be incorporated in production planning. In 1956 Kennecott instituted a program to provide the resources necessary to develop and maintain a slope mechanics capability, including technical knowledge, engineers, and instruments. Although the goal has not been fully achieved, very significant progress has been made. Other papers (3, 4, 7, 8, & 12) have described the purposes and detailed results of the most recent study carried out at the Kimbley Pit. The study has provided valuable experience and has given the industry a three dimensional picture of the stability variables that influence a mine slope. The study has better defined those areas which require further investigation and has indicated those design and analytical techniques which can be used with confidence. In effect, the study has paved the way for the next step; that of refining the design process and applying it for profit.

Jan 1, 1968

By N Harries

The management of risks associated with slope instability is an essential process in the safe and economic operation of open cut mines. The æslope stability radarÆ (SSR) has been developed to better manage those risks. The SSR can remotely scan a rock slope to continuously measure any movement of the face. The system can detect and alert users of wall movements with submillimetre precision. The high level of movement precision and broad area coverage of the rock face can allow for a better understanding of the geomechanics of slope deformation, including magnitude of potential failures and additional warning time of impending instability. Additionally, radar waves adequately penetrate through rain, dust and smoke to give reliable measurements, 24 hours a day. SSR systems have been deployed in many mines in Australia, Indonesia, Africa, Chile and the United States. Greater than 100 rock falls and waste dump failures (from several tonnes to millions of tonnes) have been monitored, and on every occasion precursor æwarningÆ movements were recorded by the SSR. This technology enables a radical change in the management of risks in open cut mining. This paper presents recent case studies of how the SSR technology has provided safety and productivity benefits to large open cut metalliferous mines.

Jan 1, 2007

By Neal Harries

Ground movement is normal in open cut mining operations, mainly caused by excavation response and blasting. Movement of the ground can be acceptable provided it is not unexpected and catastrophic. However, in steep mine walls and the very large open pits being developed today the consequence of slope collapse can be catastrophic. Such risks can be minimized at the planning stage by reducing slope angles, but this carries a very high cost. Also, instabilities which develop whilst mining can lead to ore reserves being quarantined, which represent a high cost to the mining operation. In spite of such safety measures, unexpected failures have occurred in the past. These issues motivated the development and production of the slope stability radar (SSR). There are currently over 80 GroundProbe SSR systems deployed in metalliferous and coal mines in 17 countries. The unexpected failure of rock walls at mining sites is a major cause of death and serious injury. Slope failure is also one of the major causes of economic and production losses. An unexpected wall failure can bury critical equipment. It also disrupts the mine plan. It is common to cease mining for several days or weeks following a wall collapse due to uncertainty over stability. Direct economic losses in remediation alone can easily exceed $1,000,000 per incident. The economic costs of injury or fatality are much higher including closure of mines during the incident investigation process. Massive wall failure can result in direct and indirect costs measured in millions of dollars. This paper will present some recent case studies of the SSR operation in open cut mines in North America, including Thompson Creek Mining Company (Idaho), Smoky Canyon Mine (Idaho), and a general case study on extreme cold weather use of the SSR.

May 1, 2009

Slope stability is a critical safety and production issue for open cut mines. The æslope stability radarÆ has been developed to remotely scan a rock slope to continuously measure the movement of the face. The system can detect and alert movements of a rough wall with sub-millimetre precision, and with reliability and resolution. The advantage of the slope stability radar over other monitoring techniques is that it provides full area coverage without the need for mounted reflectors or equipment on the wall. In addition, the radar waves adequately penetrate through rain, dust and smoke to give reliable measurements, 24 hours a day. The measurement technique is tolerant of vibrations and overcomes the need for a highly stable footing required by traditional surveying systems, making it easy to move from one location to another. The system is self-powered and designed for minimal maintenance. Radar displacement images, co-registered with digital photography images, are transferred from the radar site in the pit to the mine office via a radio telemetry link. Custom-written software provides mine managers and geotechnical engineers with a complete picture of slope movements over defined time intervals. The time-history of the movement of any selected points or regions on the slope can also be displayed. Also provided is the ability to set movement thresholds that will trigger alarms at the radar site or mine office. The system has been used at numerous coal and metalliferous mines in Australia, and has provided real-time monitoring of slope stability during active mining operations. More than 20 rock wall and spoil failures have been captured by the system, and on every occasion adequate warning was provided to mine operators. The high level of movement precision and broad area coverage of the rock face provides a better understanding of the geodynamics, which leads to extra warning time. This technology enables a radical change in the management of risks in open cut mining operations.

Jan 1, 2003

By Jorge Cárdenas, Diego Gamarra

In previous phases of the mine, a landslide resulted in several losses in production delays. The stability of slopes in a mining operation is critical for the sustainability of the operation, as they are exposed to vibrations and damage caused by blasting. Therefore, it is essential to implement controls and innovative technologies to reduce these vibrations levels. This study focuses on the application of low-energy emulsions with lower densities than conventional explosives, developed to reduce vibrations and the energy delivered to the rock mass adjacent to the near blast holes as a buffer row. Near field studies were carried out by embedding triaxial geophones. Vibrations were recorded, and mathematical models of vibration associated with different types of explosive mixtures were generated. This allowed us to determine the benefit of implementing low-density explosives in reducing vibrations compared to Heavy ANFO explosives. The application of low-energy explosives with densities ranging from 0.7 to 0.8 g/cm³ and Relative Bulk Strength (RBS) of 51-65 allows for a 40% reduction in vibrations compared to the detonation of Heavy ANFO explosives.

Jan 21, 2025