Search Documents

By N. S. Voiloshnikova

Large-scale continuous ?Resin-In-Pulp? process tests were conducted at Irgiredmet. The object for testing was the sample of oxidized gold ore from one of Siberian deposit. Weak-base ion ex-change resin PuroGold was used as adsorbent. The duration of ?Resin-In-Pulp? tests was sufficient for a completing of three cycles ?Adsorption/Elution?. Gold in feed was 0.95 mg/L. Gold in solid phase of adsorption tails? 0.065 g/t. Gold in liquid phase of adsorption tails? 0.026 mg/L. Total gold in adsorption tails ?0.11 g/t. Gold recovery ?94.3 %. The use of regenerated resin had practically no effect on gold losses with adsorption tails. Alkaline cyanide solution (NaCN-20g/L, NaOH- 5g/L) was used as eluent for gold elution from loaded resin. Elution temperature ?60 °C. Number of eluent bed volumes passed ?10. Loaded resin analysis was following (g/ton): Au? 1700~1250; Ag? 400~460; Cu? 250~450; Zn? 5100~9600; Fe? 860~1200. Elution efficiency: Au? 95.3%~97.8%; Ag? 84.0%~88.0%; Cu? 84.0%~88.0%; Zn? 97.0%~99.0%. Although high zinc resin loading was shown zinc was eluted efficiently. The adsorption properties of fresh PuroGold resin, PuroGold resin after 3 cycle ?Adsorp-tion-Elution?cycles in comparison with AM-2B resin were tested. It was shown from adsorption isotherms that selectivity of PuroGold resin slightly less in comparison with AM-2B resin mainly due to its higher zinc adsorption properties. It was founded on base of test results that adsorption properties of PuroGold resin was practically constant during three ?Adsorption/Elution? cycles. Gold may be efficiently recovered by resin tested. There were no difficulties during gold elution from loaded resin and its regeneration. PuroGold resin was recommended for industrial use in RIP process. Process design criteria were developed and plant design is on progress at the moment.

Jan 1, 2014

By James Howe

EVERY engineer and user of wire rope is desirous of information that will enable him to determine whether the performance of any particular piece of rope is satisfactory, and what conditions can be changed so as to increase the life of a rope. In most cases, it is far from easy to analyze the conditions of service and tell which is the greatest factor in determining the life of wire rope. If we start on a layout for an entirely new rope system, the task of making conditions satisfactory is simplified so far as the engineering details are concerned; but if the plant requiring wire rope is in operation, any change is likely to involve the expenditure of consider-, able money to replace and change over machinery that must be kept in constant operation, because a large monetary loss will result from a shutdown for even a few days. Often wire rope is kept operating under bad conditions, as the user thinks that it is cheaper and quicker to replace the rope than to make alterations in the hoisting machinery. A typical case is a metal mine operating in what is now almost the center of a large mining city, where it owns a few acres of mineral rights. It was expected that the shaft would go to a depth of 1000 ft. (305 m.), so a moderate sized rope, about 1 ¼ in. (31.7 mm.), was used on a 6-ft. drum with a 7-ft. head-frame sheave and rather short lead from drum to head sheave. This mine has gone deeper each year until, it is now 2500 ft. deep and the rope speed has been increased from 1500 ft. per min. to over 3000 ft. The original rope just filled the drum in one layer, now it overwinds three layers. The original ropes were probably 6 X 19 crucible steel and lasted from 12 to 18 mo.; now, the highest grade plow steel is used, yet the average service is only about 6 mo. The cause is not hard to find. If the engineers had known at the outset what would be done with this hoist, the design would have been very different. Conditions at this mine, from a wire rope standpoint, have gradually become worse and it is difficult to see how rope service on this hoist can be com-pared with the service of previous years with any fairness to the wire-

Jan 2, 1922

By H. Salamanca

HighService has developed different equipment using wireless technology and machine vision systems that were specially designed to allow 1) the online determination of the SAG mills liner's service life, 2) the automatic detection of a missing dipper tooth in mineral extraction shovels, 3) the reduction of accident risk potential in the mineral transportation within the mine, and 4) the reduction of collision risk potential between shovels and wheel dozers during mineral extraction. For the development of all these systems at HighService, extensive research has been done in radio frequency and image processing fields. The integration of both technologies with the expert knowledge of the company on the typical harsh environment conditions of the mining industry has led to the development of heavy duty equipment that tolerate the extreme mechanical requirements of SAG mills and electrical mining shovels.

Jan 1, 2007

By Steven Bradshaw, Edson Charikinya

The application of high power microwave energy to secondary crusher products has been shown to induce micro fractures and cracks in the ore. This suggests that heap leaching could benefit from microwave-induced fractures, as the extent and kinetics of heap leaching processes depend on the accessibility of grains to lixiviants, which can potentially be improved through microwave treatment. The density and pattern of microwave induced cracks and how these cracks subsequently affect heap leaching recovery has not yet been investigated. The objective of this study was to apply X-ray micro computed tomography (X-ray CT) to investigate microwave induced cracks in large cone and HPGR crushed sphalerite particles within 3D space. The ore particles were microwave treated in a single mode microwave applicator coupled to a switched mode power supply and a water cooled microwave transmission sub system operating at 2.45 GHz. The ore particles were treated at specific absorbed microwave heating energies of between 2 and 3kWh/t by treating at 6 kW of forward power for treatment times of 1 s. X-ray tomography analysis was conducted on fine (-5+4.75) mm, medium (-16+9.5) mm, and large (-25+19) mm sphalerite particles before and after microwave treatment at voxel resolutions of 5 µm, 15 µm and 25 µm respectively. Image segmentation, thresholding and spatial registration techniques were used to study crack patterns in 3D images of HPGR and cone crushed particles. Analysis of the X-ray CT images after microwave treatment shows considerable micro crack formation within the Cone and HPGR crushed particles. The cracks pattern showed interphase cracks propagating across all phases, with no evidence of preferential cracking. A greater density of microwave induced cracks was observed on fine (-5+4.75) mm particles compared to the medium (-16+9.5) mm and (-25+19) mm large particles. The results showed overall increased particle porosity following microwave treatment.

Jan 1, 2014

Particles for heap leaching in conventional circuits are prepared using Cone crushers. Cone crushers are used to crush the ore to the size range between 12-25 mm for heap leaching operations. Leaching from these relatively coarse particles occurs only at the surface and in subsurface regions, which are accessible from the surface by cracks and pores. Since leaching is active in accessible areas, the method of comminution that forms multiple cracks and pores would offer an advantage for heap leach. An investigation was performed in this study to assess if the HPGR forms more cracks and pores than a Cone crusher. X-ray computed tomography (CT) was used to characterize the degree of cracks and pores formed by these two comminution devices that can be used for heap leaching feed preparation. In order to compare the effect of the comminution method on crack network generation, a bulk sample of the zinc ore was crushed by the HPGR at three different pressure settings (45, 95 and 120 bar), the sample ore was also crushed with a Cone crusher for comparison purposes. Products from the Cone crusher and HPGR experiment were then screened into five size fractions ((-25 +19), (-19+16), (-16+9.5), (-9.5+5), (-5+4.75) mm), Subsamples from the ((-25 +19), (-16+9.5), (-5+4.75) mm) size fractions were analysed. The spatial distribution of the crack network of sphalerite particles was characterized using a highresolution industrial X-ray CT system. This paper describes the use of image analysis techniques including image segmentation, which uses a combination of thresholding and other methods to characterize and quantify crack and mineral dissemination in the sphalerite particles after comminution with the HPGR and Cone crusher. The results are validated with those obtained using traditional techniques such as physical gas (with N2) adsorption, mercury intrusion porosimetry, SEM and QEMSCAN.

Jan 1, 2012

By J. T. Kalala

Particles for heap leaching in conventional circuits are prepared using Cone crushers. Cone crushers are used to crush the ore to the size range between 12-25 mm for heap leaching operations. Leaching from these relatively coarse particles occurs only at the surface and in subsurface regions, which are accessible from the surface by cracks and pores. Since leaching is active in accessible areas, the method of comminution that forms multiple cracks and pores would offer an advantage for heap leach. An investigation was performed in this study to assess if the HPGR forms more cracks and pores than a Cone crusher. X-ray computed tomography (CT) was used to characterize the degree of cracks and pores formed by these two comminution devices that can be used for heap leaching feed preparation. In order to compare the effect of the comminution method on crack network generation, a bulk sample of the zinc ore was crushed by the HPGR at three different pressure settings (45, 95 and 120 bar), the sample ore was also crushed with a Cone crusher for comparison purposes. Products from the Cone crusher and HPGR experiment were then screened into five size fractions ((-25 +19), (-19+16), (-16+9.5), (-9.5+5), (-5+4.75) mm), Subsamples from the ((-25 +19), (-16+9.5), (-5+4.75) mm) size fractions were analysed. The spatial distribution of the crack network of sphalerite particles was characterized using a highresolution industrial X-ray CT system. This paper describes the use of image analysis techniques including image segmentation, which uses a combination of thresholding and other methods to characterize and quantify crack and mineral dissemination in the sphalerite particles after comminution with the HPGR and Cone crusher. The results are validated with those obtained using traditional techniques such as physical gas (with N2) adsorption, mercury intrusion porosimetry, SEM and QEMSCAN.

Jan 1, 2012

By D. M. Abbott

The problem with best practices occurs when they do not work. This happens when the seldom-stated assumptions underlying the practice are not met. This paper provides some examples for the mining industry: (1) when core splitting is inappropriate, (2) when the use of fire assays for placer samples is inappropriate, and (3) when high-grading may be acceptable. Geologic conclusions are, in the final analysis, expressions of judgment predicated upon knowledge and experience. A geologic conclusion, however, purports to be more than an arbitrary determination—it is reached as a consequence of method. No specific method is required, but the method used must be an orthodox method, in accordance with orthodox definition of terms, and the one best adapted to the dealing with the questions asked about the property in question. Whether the so-called “best practice” is really applicable to the job at hand must be decided on the basis of professional scientific judgment. When one decides to deviate from a published “best practice” for sound scientific reasons, describe in detail in the report what the so-called “best practice” is, why it was inappropriate for the project, and why the method used was better. If one becomes aware that a “best practice” is being proposed, actively urge those proposing it to include in its description the underlying assumptions that must be met in order for the “best practice” to be valid.

Jan 1, 2014

By J. E. Tobey, David R. Mitchell, J. H. Kerrick

DETAILED knowledge of purchase specifications established by coal consumers is essential to the successful design and operation of a coal-preparation plant. ANTHRACITE Specifications should be considered by both the consumer and the producer as guide posts outlining a certain path for both to follow. Plants differ, therefore specifications must differ to meet the varied requirements. Specifications are not of themselves a "cure all" or an assurance of complete satisfaction in fuel utilization. Specifications should not be regarded as a license to engage in an orgy of buying any and all coals that may happen to fall within their limits. This would lead to the-indiscriminate mixing of coals which may vary in their burning characteristics. Different coals of equal grade tend to be individualistic in their burning characteristics. Rather, specifications should be used to help simplify coal selection, to reduce the actual number of coals used over a given period; in other words, to have a stabilizing influence on coal or customer turnover. In the final analysis, the use of too many coals per year in a plant is costly to both the consumer and the producer. Too many sources usually result in higher operating and maintenance costs for the consumer and higher sales costs for the producer. Finally, the statement included in the report accompanying the comprehensive Coal Selection Charts prepared by the Coal Committee of the National Association of Purchasing Agents, and released in 1938, is significant. This Committee worked diligently for a period of 15 years seeking to find a scientific and reliable method for selecting coals. The two following paragraphs are quoted from its report: More important is the fact that no ready-made classification or set of specifications can possibly replace the judgment and resourcefulness of an experienced combustion engineer, or fuel technologist, nor the usual need for full scale plant tests under the exact conditions of use before a final decision is made . . .

Jan 1, 1943

By J. E. Tobey, David R. Mitchell, J. H. Kerrick

DETAILED knowledge of purchase specifications established by coal consumers is essential to the successful design and operation of a coal-preparation plant. ANTHRACITE Specifications should be considered by both the consumer and the producer as guide posts outlining a certain path for both to follow. Plants differ, therefore specifications must differ to meet the varied requirements. Specifications are not of themselves a "cure all" or an assurance of complete satisfaction in fuel utilization. Specifications should not be regarded as a license to engage in an orgy of buying any and all coals that may happen to fall within their limits. This would lead to the indiscriminate mixing of coals which may vary in their burning characteristics. Different coals of equal grade tend to be individualistic in their burning characteristics. Rather, specifications should be used to help simplify coal selection, to reduce the actual number of coals used over a given period; in other words, to have a stabilizing influence on coal or customer turnover. In the final analysis, the use of too many coals per year in a plant is costly to both the consumer and the producer. Too many sources usually result in higher operating and maintenance costs for the consumer and higher sales costs for the producer. Finally, the statement included in the report accompanying the com¬prehensive Coal Selection Charts prepared by the Coal Committee of the National Association of Purchasing Agents, and released in 1938, is significant. This Committee worked diligently for a period of 15 years seeking to find a scientific and reliable method for selecting coals. The two following paragraphs are quoted from its report: More important is the fact that no ready-made classification or set of specifications can possibly replace the judgment and resourcefulness of an experienced combustion engineer or fuel technologist, nor the usual need for full scale plant tests under the exact conditions of use before a final decision is made ...

Jan 1, 1943

By J. E. Tobey, David R. Mitchell, J. H. Kerrick

DETAILED knowledge of purchase specifications established by coal consumers is essential to the successful design and operation of a coal preparation plant. ANTHRACITE Specifications should be considered by both the consumer and the producer as guide posts outlining a certain path for both to follow. Plants differ, therefore specifications must differ to meet the varied requirements. Specifications are not of themselves a "cureall" or an assurance of complete satisfaction in fuel utilization. Specifications should not be regarded as a license to engage in an orgy of buying any and all coals that may happen to fall within their limits. This would lead to the indiscriminate mixing of coals which may vary in their burning characteristics. Different coals of equal grade tend to be individualistic in their burning characteristics. Rather, specifications should be used to help simplify coal selection, to reduce the actual number of coals used over a given period; in other words, to have a stabilizing influence on coal or customer turnover. In the final analysis, the use of too many coals per year in a plant is costly to both the consumer and the producer. Too many sources usually result in higher operating and maintenance costs for the consumer and higher sales costs for the producer. Finally, the statement included in the report accompanying the comprehensive Coal Selection Charts prepared by the Coal Committee of the National Association of Purchasing Agents, and released in 1938, is significant. This Committee worked diligently for a period of 15 years seeking to find a scientific and reliable method for selecting coals. The two following paragraphs are quoted from its report: More important is the fact that no ready-made classification or set of specifications can possibly replace the judgment and resourcefulness of an experienced combustion engineer or fuel technologist, nor the usual need for full scale plant tests under the exact conditions of use before a final decision is made.

Jan 1, 1950

By Sam F. Harrison

Most hydraulic system malfunctions make their presence known by sending out warnings that are loud and clear to the initiated mechanic, according to Aeroquip Corp. service engineers. To detect problems in many systems, they suggest that the use of four senses-sight, smell, hearing and touch-and a knowledge of how to interpret the information gathered are all that's needed to identify hydraulic malfunctions.

Jan 3, 1978

By H. I. Smith

THE technical and safety press have devoted much space in support of or in opposition to the use of booster and auxiliary fans in coal mines. The Mine Safety Board of the U. S. Bureau of Mines has given the matter consideration, and the Mine Ventilation Committee of the A. I. M. E. is now seeking a discussion of the merits and demerits of such fans to guide it in formulating recommendations. In this paper, I will set up some principles on which I believe most engineers will agree and from which we may work toward a decision, though as to what that decision shall be there may be a difference in opinion. Before stating the points on which I believe. there is accord, I will distinguish between booster and auxiliary fans.

Jan 1, 1927

By Jing Zhou

2-hydroxy-3-naphthoy hydroxamic acid code name F203 is a good collector of cassiterite, 1-hydroxy-2-naphthoy hydroxamic acid code name ZJ-3. F203 and ZJ-3 are similar series of isomers. They have similar naphthye, and similar series of functional OH and ?CONHOH, but the seat of OH and ?CONHOH group are different, on the F203 is 2.3; on the ZJ-3 is 1.2, ortho position too. According to Isomeric principle ZJ-3 is a good collector of cassiterite slime too. Using ZJ-3 as collector flotation -10µm occupies 90%, grade 1.16% Sn cassiterite slime of Da Chang Chehe concentration plant, pass one coursing flotation, two cleaning and one scarenging flotation, and obtains grand 18.26% Sn, recovery 92.68% cassiterite concentrate. The result proves the Isomeric principle of flotation reagents is correct again. This principle may supply to synthetize new flotation reagents reference. Keywords: F2O3, ZJ-3, cassiterite flotation, Isomeric principle, Isomeric principle of flotation reagents

Sep 1, 2012

By R. D. Hancock

The loading and selective properties of a number of commercial and experimental resins developed for the extraction of base metals were evaluated. Particular applications that ",:ere considered included the extraction of copper from artificial dump liquors, the treatment of Iow-grade copper, nickel, and cobalt liquors, and the removal of nickel from a cobalt electrolyte. Reagents that showed promise were two experimental resins developed at Mintek containing pyridyl imidazole active groups and two Dow resins, XF4195 and XF4196.

Jan 1, 1982

By William G. Pariseau, Mark K. Larson, Heather E. Lawson

Rational design based on engineering fundamentals is essential for the layout of safe, stable shafts and tunnels. Shafts and tunnels including winzes, raises, adits, and crosscuts are lifelines to the underground and must be secure. The contribution of this paper describes a significant extension in existing software previously developed for five important design problems in strata-bound mines such as coal, trona, salt, potash, and some large, lead-zinc mines. This extension in software allows analysis to proceed in three easy steps: (1) preparation of a strata properties file, (2) generation of the finite element model, a mesh, and (3) finite element program execution. Circular, elliptical, and rectangular shaft sections are available for a single shaft, twin shafts, and shafts in a row. Spacing of twin shafts and shafts in a row is a free parameter (pillar width). Tunnel shapes are the same as shafts but include the conventional arched back section. Dipping strata of variable thickness, depth and orientation relative to the excavation of choice are allowed. The analyses are three-dimensional. An elastic-plastic material model based on associated rules of flow and an N-type yield condition for isotropic, transversely isotropic, or orthotropic rock are used for all strata. Example analyses from several hardrock mines are provided to illustrate the three-step process including mesh plotting and plotting of selected results. The goal of this software is to advance mine design technology for improved miner health and safety.

By William G. Pariseau, Mark K. Larson, Douglas R. Tesarik, Heather E. Lawson

"This contribution describes development and application of a user-friendly finite element program, UT3PC, to address three important problems in underground coal mine design: (1) safety of main entries, (2) barrier pillar size needed for entry protection, and (3) safety of bleeder entries during the advance of an adjacent longwall panel. While the finite element method is by far the most popular engineering design tool of the digital age, widespread use by the mining community has been impeded by the relatively high cost of and the need for lengthy specialized training in numerical methods. Implementation of UT3PC overcomes these impediments in three easy steps: First, a material properties file is prepared for the considered site. Next, mesh generation is automatic through an interactive process. A third and last step is simply execution of the program. Examples using data from several western coal mines illustrate the ease of using the application for analysis of main entries, barrier pillars, and bleeder entry safety.INTRODUCTIONRational design of safe underground entries and crosscuts, barrier pillars, and bleeder entries begins with a site-specific analysis of stress. An analysis of stress identifies the critical regions of high-stress concentration where yielding is likely and additional or more focused ground control measures are needed. This analysis also identifies regions where stress concentration is low, and risk mitigation is less urgent. Displacements induced by mining, including roof sag, floor heave, and pillar squeeze, are also of importance to stability. The popular finite element method is well-suited for such analysis and has been in use for studying coal mine engineering problems since the late 1960s (Dahl, 1969). The method has been taught in undergraduate engineering curricula for many years and offers an alternative to existing design procedures based mostly on rules of thumb, empirical methods based on mine data, and predigital-age concepts of strata mechanics. However, despite the versatility of the finite element method, usage has been limited, mainly because of the cost of the software and the required training in numerical methods.The program UT3PC (Pariseau, 2017) has evolved from early two-dimensional versions in the era of mainframe computers. These early versions were still quite limited using only a few hundred elements that required overnight turnaround times. Recent versions of UT3PC are convenient and efficient desktop programs that use several million elements. With the advent of personal computers in the mid-1980s and subsequent increase in computer speed, expanded memory, and lower costs, applications for mining increased in three-way cooperative projects among industry, the former U.S. Bureau of Mines, and academia. The Spokane Research Center of the U.S. Bureau of Mines, in cooperation with the University of Utah, developed a two-dimensional desktop finite element program, UT2PC, available to the mining community in 1991. This was a short course offered at the 1991 SME Annual Meeting in Denver, CO."

Jan 1, 2017

Enable prospective in situ leach mine operators to evaluate the economic potential of an ore body by using a user-friendly, computerized in situ copper oxide leach mining cost model. Background As part of its research on in situ leach mining technology, the Bureau of Mines produced a 5-volume contract report that mining companies can use to design an in situ mining operation for copper oxide deposits. Written for the Bureau by the Science Applications International Corporation (SAIC) in 1988, the generic design manual also contains a computerized cost model for evaluating the economic feasibility of in situ leach mining for any specific copper oxide deposit. The cost model is to be used with Volume II of the contract report. But because of certain complexities associated with running it, the Bureau found that the model could be improved by making it more user friendly. Approach The approach taken by Bureau researchers to make the original model more user friendly was to incorporate a HELP function to define input parameters, and to enable the display of output on the monitor. An accompanying handbook, U.S. Bureau of Mines Information Circular (IC) 9284, contains further details on running, the 1990 model.

Jan 1, 1991

Here are the details . . . . . of how a $2.5 million research gamble, now backed by five years of intensive development in cooperation with the Chemical Construction Corp. resulted in a hydrometollurgical process that yields pure metal powders from sulphide concentrate - a process that offers potential savings of $2.5 million a year.

Jan 6, 1953

By Milton Glicken

The airborne geophysicist is a busy man these days. In his plane he may have the airborne magnetometer, the airborne scintillation counter, and the airborne electromagnetic surveying system. Each of these is an independent tool, but all require additional auxiliary equipment for locating the aircraft in space: recording altimeters and Shoran or aerial cameras. Now there is still another piece of equipment, the airborne magnetic gradiometer, an accessory to the magnetometer. To understand its uses, consider the function of the magnetometer itself. Aside from detecting magnetic ore, the airborne magnetometer finds greatest use in spotting intrusions of igneous material. Where there is enough contrast in magnetic susceptibility of igneous rock and adjacent formations, it outlines the intrusion. Certain minerals also influence the magnetometer directly, but with the exception of magnetite and possibly one or two others, their effect is weak and can be detected only when there is sufficient ore and the magnetometer flight passes very close to it.

Nov 1, 1955

By Roland D. Parks

Corundum, little publicized as an industrial abrasive, has, in its small way, contributed greatly to the production of many specialized items vital to our war program and to Our allies. Optical elements Of the highest quality for range finders, bombsights, and scientific instruments; precision metal parts for torpedoes and airplane engines; quartz crystal plates for military radios; armorplate and malleable castings for tanks and guns; and eyeglasses for everyone; these are some Of the products that corundum has helped to produce in the quantities needed and on time. Unlike metals and many other raw materials, corundum is not incorporated into any Of these finished products. It is simply a grinding medium used to produce the desired finish or precision; an operating supply or tool, so to speak. With a Mobs' scale index of 9, corundum ranks next to the diamond in hardness among the natural minerals and is superior to emery and garnet. The gem varieties of corundum, including the Oriental ruby and sapphire, are frequently more highly prized as jewels than the diamond. It is the intent Of this paper to deal Only with a description of the corundum industry, the administration of wartime control, and certain economic aspects as seen by the author. Several references are listed to assist anyone who wishes further information on the geological occurrence of the mineral. Ore Production and Consumption For the past two decades, south Africa has been the world's sole producer of corundum ore. A possible exception is Russia, where, it is understood, there was considerable production during the thirties for domestic consumption but for which statistics are lacking. The United States is the world's principal consumer of corundum ore; imports lor the period 1934 through 1940 averaging 3000 Short tons per year, The years 1935 and 1936 were close to the 5000-ton mark, and imports during 1941, the last prewar year for which statistics have been released, were approximately 6000 Short tons. Again lacking statistics on Russia, the United Kingdom ranks second, but far below the United States in consumption of ore. Historically, corundum has been found in some 35 countries throughout the world, but the principal deposits are in South Africa, Canada, Madagascar, Russia and the united States. Deposits are generally small and subject to rapid exhaustion. Thus, the United States was the principal world producer for the period 1870 to 1900, when operations ceased except for two years during World War I. India was a producer of ore from 1898 through 1921, with peak output in 1916 through 1918 Canada came into production in 1901 with substantial output of ore and finished grain until 1914; the production thereafter was smaller until 1921. Madagascar has produced ore since 1910 but has had important output in only a few scattered years. South African production started in 1912

Jan 1, 1948