Search Documents

In this U.S. Bureau of Mines report, proposed narrow-vein and longwall mining concepts using drill-split technology (described in part 1 of this series) and in situ liner concepts (described in part 2 of the series) are combined and applied conceptually to environmental problems. Proposed applications deal with (1) acid mine drainage (AMD), (2) solid waste disposal, (3) site remediation, and (4) pollution prevention through innovative industrial design. For control of AMD from abandoned hillside mine workings, it is proposed that source veins be re-mined, processed for residual values, then backfilled using an impermeable compound backfill mix. For solid waste disposal, "vertical landfills" are proposed, consisting of trash-backfilled underground rock quarries. Vertical landfill activities take place in in situ lined containments that geohydrologically isolate the mining-backfilling activities. Site remediation through the creation of in situ underliners, for the capture of toxic leachates, and pollution prevention through the underground storage of toxic, flammable, and explosive materials in in situ containments, are proposed.

Jan 1, 1995

By Charles V. Jude

This U.S. Bureau of Mines report presents a review and evaluation of existing and new backfilling materials and methods for their applicability to the problem of gate road stress reduction in deep retreat longwall coal mines. Candidate backfill materials include pulverized coal combustion fly ash, flue gas desulfurization, and fluidized bed combustion by-products from coal-fired electric power generation plants. Properties of both backfill and its component materials are presented, with particular emphasis on the unconfined compressive strength and elastic modulus of backfill mixtures. Hydraulic mix designs discussed in this report include high-water content slurry and low-water content paste fills. Three gate road stress-transfer-modification concepts are proposed to reduce abutment stresses in gate road systems. The first concept, packwalling, involves packwall construction behind the headgate shield inby the face and adjacent to the headgate pillars. The second concept, gob-filling, involves infilling a strip of gob inset from and parallel to the headgate using paste injection methods patterned after a technology recently developed in Europe. In the third concept, entry-filling, slurry fill methods are used to fill abandoned gate roads and crosscut entries inby the face.

Jan 1, 1995

By G. L. Mowrey, S. D. Maksimovic

An important element of the U.S. Bureau of Mines (USBM) mining research program is the development and evaluation of reliable coal interface detection (CID) systems. Commercially available CID sensors based on natural gamma radiation (NGR) are only applicable if the immediate roof is composed of shaley material. The USBM has made numerous underground and laboratory measurements using several NGR systems approved for installation on mining machines by the Mine Safety and Health Administration. In addition, two small handheld NGR instruments were used to make comparative measurements. Underground NGR measurements in 10 different coal seams, potassium-uranium-thorium radiometric analyses on samples from 16 seams, and chemical analyses of coal and rock for correlation with NGR counts were made. Laboratory test results on the effect of air gap and sample thickness, size, and weight on the NGR measurements, as well as general results of the various NGR systems, are discussed.

Jan 1, 1995

By D. J. MacDonald

This U.S. Bureau of Mines report reviews published information on synthetic berlinite (AlP04) and suggests experimental conditions requisite for its production. Berlinite is a piezoelectric material with potential use as a substitute for quartz in the crystal oscillators, which are components of electronic and electroacoustic equipment. Information gathered here (mostly from published sources) includes historical background, physical properties, end-use applications, criteria of quality, and physio-chemical factors involved in berlinite crystal growth. It is concluded that growing large high-quality berlinite crystal would require high-purity starting materials in an autoclave equipped with a noncorrodible liner and operated with temperature control of ±O.OO5 ac over a range of 250 to 350 ac.

Jan 1, 1995

By John E. Hamak

The identified helium resources of the United States were estimated by the U.S. Bureau of Mines at 617 Bcf, as of December 31, 1992. This includes 285 Bef of demonstrated reserves, 85 Bcf of demonstrated marginal reserves, and 37 Bcf of demonstrated sub-economic resources. The identified resources also include 166 Bcf of helium in inferred reserves and inferred marginal reserves and 44 Bcf in inferred sub-economic resources. The identified helium resources contained on Federal lands are approximately 172 Bcf, including 32 Bcf in underground storage in the Cliffside Gasfield near Amarillo, TX. Undiscovered helium resources in the United States are estimated at a most likely volume of 104 Bef, with a maximum volume of 249 Bcf and a minimum volume of 41 Bef. Also reported are 51 Bcf of helium in nonconventional and low-helium-content natural gases. Extraction of helium in the United States occurs mostly from natural gases produced from the Hugoton gas area in Kansas, Oklahoma, and Texas, and the Riley Ridge area in southwest Wyoming. Helium extracted from natural gas in the United States in 1992 was 3.3 Bcf. Some shortfalls in helium supply may occur in about 5 to 10 years.

Jan 1, 1995

By Robert F. Holub

The U.S. Bureau of Mines (USBM) has tested a personal dosimeter for measuring radon decay products that is manufactured by Tom Scurry Associates. The tests were made to determine the accuracy of the dosimeter system for record keeping of radiation exposures to radon decay products encountered in mining. The radioactivity-detecting head is based on a design developed by the USBM, and the associated air pump was developed by the manufacturer. The dosimeter system was tested in the USBM radon chamber. The detecting head uses CaF:Dy thermoluminescent phosphors and is mounted on a self-regulating air pump. Batteries supply power sufficient for an 8-h shift. The dosimeter system is worn on the miner's belt. Dosimeter calibration tests were performed by the USBM. In addition, the pumps were tested and evaluated under continuous flow conditions. The results of these tests indicate that the Tom Scurry Associates Model DOSI600 dosimeter is suitable for general use in mines where record keeping for natural radiation exposure is required.

Jan 1, 1995

By Joan K. Kuenzi

The purpose of this U.S. Bureau of Mines information circular (Ie) is to discuss how job analysis methods taken from different disciplines can be used together to form a more complete picture of jobs in the mining industry. "Job analysis" is a term used by many researchers, but use of the term is far from standardized. Authors of papers on this subject often state that there is confusion in how or why jobs are to be analyzed, what the resulting information is to be used for, and what the "job analysis" actually means. The process of breaking a job into elemental tasks and analyzing them is used to determine what skills and knowledge are needed to perform a given job, to improve efficiency, and to develop safer job procedures. All are valid reasons to analyze jobs, but the methods used to accomplish the analyses may be very different. In order to create a more complete picture of a job, it may be useful to incorporate methods and information from different areas of study rather than choosing one method for analysis.

Jan 1, 1995

By Fred N. Kissell

This U.S. Bureau of Mines report is a guide for the control of air contaminants during tunnel construction. Topics discussed are calculating air quantity requirements, types of ventilation systems, planning ventilation systems, control of methane gas, control of dust, control of diesel emission, ventilation to remove blasting fumes, measuring airflow, and measuring gases. This report does not provide detailed design information, but seeks to answer practical questions on air contamination issues.

Jan 1, 1995

By Christopher Mark

This proceedings volume contains papers presented at technology transfer seminars sponsored by the National Institute for Occupational Safety and Health (NIOSH) on New Technology for Ground Control in Retreat Mining. The seminars were conducted at five locations: Uniontown, PA (March 26, 1997), Norton, VA (April 8, 1997), Pikeville, KY (April 10, 1997), Charleston, WV (April 17, 1997), and Evansville, IN (April 22, 1997). The papers presented here describe several new, highly practical technologies developed by the NIOSH Pittsburgh and Spokane Research Centers3 to improve safety during pillar retreat operations. Two central issues are addressed: pillar design and mobile roof supports (MRS's). Proper pillar sizing is essential for safe pillar extraction. The Analysis of Retreat Mining Pillar Stability (ARMPS) program and its large data base of actual mining case histories are presented. LAMODEL, a second computer program, can be used for analysis of multiple-seam and other complex mining situations. Other papers address pillar design to avoid massive pillar collapses and the proper role of coal strength testing. MRS's have greatly improved safety where they are used for pillar line support. We studied the application of MRS's at 20 mines throughout the Eastern United States. Conclusions regarding the most effective section layouts, cut sequences, and support placements are reported. Field and laboratory tests of MRS's are also described.

Jan 1, 1997

By Nicholas Kyriazi

Significant portions of the present Federal regulations for certification of closed-circuit breathing apparatus (42 CFR 84) are not quantitative. The human-subject testing portion of the regulations specifies activities rather than metabolic work rates; however, heavy human subjects have higher oxygen consumption, CO2 production, and ventilation rates than lighter human subjects performing the same activities. This means that apparatus certified using different human subjects have effectively passed different tests. In addition, apparatus performance is monitored only during selected intervals of testing, and always during rest, rather than during the entire performance period. Further, testing is arbitrarily terminated at specific rated durations, leaving unknown the performance during the remaining duration. Duration itself is misleading to users who believe that the apparatus will last a certain time no matter how much they weigh or how hard they work. The actual duration obtained from an apparatus, however, is highly variable, being inversely proportional to the work rate at which it is used. In this report, recommendations are made to (1) replace the present regulations for certification of closed-circuit breathing apparatus with quantitative tests specifying metabolic work rate rather than activity,(2) continuously monitor relevant physiological stressors, (3) continue testing until exhaustion of the oxygen source, and (4) classify closed-circuit breathing apparatus by quantity of usable oxygen, i.e., capacity, rather than by duration. Physiology-based stressor levels are suggested as well.

Jan 1, 1999

By Michael J. Pazuchanics, Thomas J. Fisher, John J. Sammarco, Jeffrey H. Welsh

This report (An Introduction to Safety) is the first in a nine-part series of recommendations addressing the functional safety of processor-controlled mining equipment. It is part of a risk-based system safety process encompassing hardware, software, humans, and the operating environment for the equipment's life cycle. Figure 1 shows a safety framework containing these recommendations. The reports in this series address the various life cycle stages of inception, design, approval and certification, commissioning, operation, maintenance, and decommissioning. These recommendations were developed as a joint project between the National Institute for Occupational Safety and Health and the Mine Safety and Health Administration. They are intended for use by mining companies, original equipment manufacturers, and aftermarket suppliers to these mining companies. Users of these reports are expected to consider the set in total during the design cycle. • 1.0 Safety Introduction.—This is an introductory report for the general mining industry. It provides basic system/software safety concepts, discusses the need for mining to address the functional safety of programmable electronics, and includes the benefits of implementing a system/software safety program. • 2.1 System Safety and 2.2 Software Safety.—These reports draw heavily from International Electrotechnical Commission (IEC) standard 61508 and other recognized standards. The scope is "surface and underground safety mining systems employing embedded, networked, and non-networked programmable electronics." System safety seeks to design safety into all phases of the entire system. Software is a subsystem; thus, software safety is a part of the system's safety. • 3.0 Safety File.—This report contains the documentation that demonstrates the level of safety built into the system and identifies limitations for the system’s use and operation. In essence, it is a "proof of safety" that the system and its operation meets the appropriate level of safety for the intended application. It starts from the beginning of the design, is maintained during the full life cycle of the system, and provides administrative support for the safety program of the full system. [ ]

Jan 4, 2001

By Thomas J. Fisher, John J. Sammarco

This report (System Safety 2.1) is the second in a nine-part series of recommendations addressing the functional safety of processor-controlled mining equipment. It is part of a risk-based system safety process encompassing hardware, software, humans, and the operating environment for the equipment’s life cycle. Figure 1 shows a safety framework containing these recommendations. The reports in this series address the various life cycle stages of inception, design, approval and certification, commissioning, operation, maintenance, and decommissioning. These recommendations were developed as a joint project between the National Institute for Occupational Safety and Health and the Mine Safety and Health Administration. They are intended for use by mining companies, original equipment manufacturers, and aftermarket suppliers to these mining companies. Users of these reports are expected to consider the set in total during the design cycle. • 1.0 Safety Introduction.—This is an introductory report for the general mining industry. It provides basic system/software safety concepts, discusses the need for mining to address the functional safety of programmable electronics, and includes the benefits of implementing a system/software safety program. • 2.1 System Safety and 2.2 Software Safety.—These reports draw heavily from International Electrotechnical Commission (IEC) standard 61508 [IEC 1998a,b,c,d,e,f,g] and other recognized standards. The scope is “surface and underground safety mining systems employing embedded, networked, and nonnetworked programmable electronics.” System safety seeks to design safety into all phases of the entire system. Software is a subsystem; thus, software safety is a part of the system’s safety. • 3.0 Safety File.—This report contains the documentation that demonstrates the level of safety built into the system and identifies limitations for the system’s use and operation. In essence, it is a “proof of safety” that the system and its operation meet the appropriate level of safety for the intended application. It starts from the beginning of the design, is maintained during the full lifecycle of the system, and provides administrative support for the safety program of the full system.

Jan 4, 2001

By Fred N. Kissell

This handbook describes effective methods for the control of mineral dusts in mines and tunnels. It assumes the reader is familiar with mining. The first chapter deals solely with dust control methods, regardless of the application. It is a brief tutorial on mining dust control and will be of help to the reader whose dust control problem does not conveniently fit any of the mining equipment niches described in later chapters. The subsequent chapters describe dust control methods for different kinds of mines and mining equipment. This includes underground coal and hard-rock mines, as well as surface mines, stone mines, and hard-rock tunnels. Because dust sampling has so many pitfalls, a chapter on methods used to sample dust is included. For those occasions when there is no practical engineering control, a chapter on respirators is also included. Except for those listed as ?future possibilities? in the longwall chapter, the dust control methods described are practical and cost-effective for most mine operators. If controlling dust were a simple matter, dust problems in tunnels and mines would have been eradicated years ago. Unfortunately, most underground dust control methods yield only 25% to 50% reductions in respirable-sized dust. Often, 25% to 50% reductions are not enough to achieve compliance with dust standards. Thus, mine operators must use several methods simultaneously, usually without knowing for sure how well any individual method is working. In fact, given a 25% error in dust sampling and day-to-day variations in dust generation of 50% or more, certainty about which control methods are most effective can be wanting. Nevertheless, over the years, some consensus has emerged on the best dust control practices. This handbook summarizes those practices.

Jan 1, 2003

By Dean H. Ambrose

A computer model was created that generates contact data by means of simulation while altering several variables associated with the machine and its operator. These variables include work environment, the operator's anthropometry, work posture, choice of risky work behavior, and the machine's appendage velocity. In the model, a contact means two or more objects intersecting or touching each other, e.g., the appendage colliding with the operator's hand, arm, head, or leg. This report documents the code development of special features of the computer model, random virtual human motions and behaviors, which made it possible for researchers to study hazardous interactions, such as contacts between the operator and machine. The original idea for random virtual human motions began with the need for a model that, when simulated, would experimentally mimic machine and human actions that could cause actual injuries or fatalities in the workplace. Injury incident investigation reports do not usually contain enough information to aid in studying this problem, and lab experiments with human subjects are also not feasible because of safety issues and ethical issues. Early investigation that evaluated the feasibility of random motions resulted in a primary programming structure and building blocks for code expansion. Basic motions and standard derivation data provided random parameters for the operator's movement in the random motion code. Experimenting with basic motions in preliminary models helped researchers devise a random motion technique that worked with xyz motion parameter values from basic motion parameters. Both values were the building blocks used in motion commands that comprised the core of the random motion code. When the code is executed in a three-dimensional computer model, it generates realistic starting positions for the operator's (virtual human) body and body parts and realistic motions mimicking a work sequence with a valid range of variation in movements. Researchers developed several rules for the random motion technique that, when applied, will maintain directional integrity of a virtual human's basic motions. From previous research, researchers formulated the algorithm that determines the behavior during machine operation. The decision algorithm was needed by the random motion code to randomly select what behavior to use for a simulation execution for a realistic representation of the operator's motions and risky behaviors during work tasks. The operator's chance of avoiding the moving appendage was also a concern to ensure that data reflecting a near-miss would not be considered a contact. Therefore, to filter a database obtained from simulations for actual contacts, it was necessary to track the operator's field of view and determine from this information when the appendage is in and out of the operator's view. NIOSH researchers successfully applied random motions and risky behaviors to examine the speed range of a roof bolter machine appendage for different workplace scenarios and compare statistically which is most likely to cause contacts (and possible injuries) to miners. Researchers in this study believe that the use of such simulations, treated with advanced statistical procedures, are extremely useful tools to evaluate the hazards of tasks where it is not possible to perform experiments with human subjects.

Jan 3, 2004

By Launa G. Mallett, Kathleen Kowalski-Trakofler, Robert H. Peters, Charles PH. D. Vaught, Peter Keating, William J. Wiehagen

On-the-job training is a common means of training or retraining workers and the practice may seem simple and straightforward. Doing it effectively however requires more thought and preparation than simply having someone follow an experienced worker around and watch what they're doing. Over the years, various techniques and practices have evolved that pass on the skills and knowledge of a trainer or coach in a manner that leads an inexperienced trainee to really absorb the information being taught. On-the-job training thus becomes less a haphazard show-and-tell and more a real transfer of information. The goal of this document is to describe how to develop or manage an on-the-job training program so that information is passed on from trainer/coach to trainee efficiently and effectively. By efficient is meant the best use of time and resources of all those involved in the training process, and by effective is meant that the trainee truly learns the skills and internalizes the knowledge needed to perform the job well. The first part of the document discusses topics to think about when developing a formal on- the-job training program. A structure based on coaching is suggested. Then a workshop designed to prepare trainers as coaches is described. Workshop materials include an instructor’s guide and trainee workbook. These materials can be used to train coaches and to assist trainees as they go through the learning process. Content related to specific jobs can be added to these materials to create targeted on-the job-training manuals. Structuring a formal on-the-job training program It is likely that some form of on-the-job training (OJT) is being conducted at your workplace. The formality of that training can range from a structured program to an informal “follow Joe around” method. If your program is completely unstructured, it may not be meeting current training needs. Worse, it may perpetuate bad habits and create “trained” employees who are not given the same information or evaluated to the same standards. Wiehagen et al. comment that, “Success in using unplanned OJT is usually dependent on the luck of the draw, that is, whether the informal trainer is competent at the task he or she is teaching, is motivated to teach, can organize the job into logical components, and knows something about good practices in teaching and evaluating” (2002, p. 27). It is only through planning a structured OJT program that consistency can be created and maintained. At the least, all trainees who have successfully completed such a program can be expected to perform at an established level—they will know what they must do to be successful.

Jan 7, 2005

By John J. Sammarco

This report (System Safety Guidance 5.1) is the sixth in a nine-part series of recommendations and guidance addressing the functional safety of processor-controlled mining equipment. It is part of a risk-based system safety process encompassing hardware, software, humans, and the operating environment for the equipment’s life cycle. Figure 1 shows a safety framework containing these recommendations. The reports in this series address the various lifecycle stages of inception, design, approval and certification, commissioning, operation, maintenance, and decommissioning. These recommendations were developed as a joint project between the National Institute for Occupational Safety and Health and the Mine Safety and Health Administration. They are intended for use by mining companies, original equipment manufacturers, and aftermarket suppliers to these mining companies. Users of these reports are expected to consider the set in total during the design cycle. • 1.0 Safety Introduction (Part 1).—This is an introductory report for the general mining industry. It provides basic system/software safety concepts, discusses the need for mining to address the functional safety of programmable electronics (PE), and includes the benefits of implementing system/software safety program. • 2.1 System Safety (Part 2) and 2.2 Software Safety (Part 3).—These reports draw heavily from International Electrotechnical Commission (IEC) standard IEC 61508 [IEC 1998a,b,c,d,e,f,g]and other standards. The scope is “surface and underground safety-related mining systems employing embedded, networked, and nonnetworked programmable electronics.” System safety seeks to design safety into all phases of the entire system. Software is a subsystem; thus, software safety is a part of the system’s safety. • 3.0 Safety File (Part 4).—This report contains the documentation that demonstrates the level of safety built into the system and identifies limitations for the system’s use and operation. In essence, it is a “proof of safety” that the system and its operation meet the appropriate level of safety for the intended application. It starts from the beginning of the design, is maintained during the full life cycle of the system, and provides administrative support for the safety program of the full system. • 4.0 Safety Assessment (Part 5).—The independent assessment of the safety file is addressed. It establishes consistent methods to determine the completeness and suitability of safety evidence and justifications. This assessment could be conducted by an independent third party. • Safety Framework Guidance.—It is intended to supplement the safety framework reports with guidance providing users with additional information. The purpose is to assist users in applying the concepts presented. In other words, the safety framework is what needs to be done and the guidance is how it can be done. The guidance information reinforces the concepts, describes various methodologies that can be used, and gives examples and references. It also gives information on the benefits and drawbacks of various methodologies. The guidance reports are not intended to promote a single methodology or to be an exhaustive treatment of the subject material. They provide information and references so that the user can more intelligently choose and implement the appropriate methodologies given the user’s application and capabilities. The guidance reports comprise parts 6 through 9 of the series and are listed below: [< 5.1 System Safety Guidance (Part 6).—This guidance supplements 2.1 System Safety. < 5.2 Software Safety Guidance (Part 7).—This guidance supplements 2.2 Software Safety. < 6.0 Safety File Guidance (Part 8).—This guidance supplements 3.0 Safety File. < 7.0 Independent Functional Safety Assessment Guidance (Part 9).—This guidance supplements 4.0 Independent Functional Safety Assessment.] [ ]

Jan 8, 2005

By Edward J. Chuhta, Joseph E. Chilton, Robert J. Timko

in underground mines to measure worker exposure to various gases such as methane, carbon monoxide, and nitrogen dioxide (NO2). Even in relatively small concentrations, NO2 can produce harmful side effects in underground workers. Mines using equipment powered by diesel engines, carrying out explosive blasting operations, and performing extensive arc welding and/or cutting work will have measurable quantities of NO2 released by these processes. Workers in these areas often use gas monitors to warn of excessive gas concentrations and to help them determine when to increase ventilation air that will dilute these gases, thus minimizing exposures to this gas. Portable gas monitors, used to measure NO2 levels, must be calibrated before each use. Calibration is typically performed using a small portable pressurized cylinder containing a certified gas mixture. The certified NO2 standard mixture, usually 10 ppm NO2 concentration, is diluted with either air or nitrogen gas. To determine the stability of commercially available portable gas standards, two different cylinders containing NO2 in nominal 10-ppm concentrations were examined. One cylinder was diluted in air, the other, in nitrogen. Baseline NO2 mixtures were generated using a standard liquid NO2 permeation tube operated at a constant temperature. Final dilutions of the test gas mixtures were made with air or with nitrogen using a mass flow-controlled gas dilution system. This study showed that, when a permeation-type NO2 generator is used, the electrochemical sensors in portable NO2 monitors provide identical results for gas mixtures whether they are diluted with air or with nitrogen. Two different gas monitors, one with a two-electrode sensor and one with a three-electrode sensor, were used to measure gas concentrations in the two commercially available cylinders. One month after the cylinders were delivered, the NO2-in-nitrogen cylinder, stated to contain 10 ppm NO2, measured 8.13 ppm. The NO2-in-air cylinder, also stated to hold 10 ppm NO2, measured 6.88 ppm. Therefore, before using NO2 gas cylinders to calibrate monitors, it is recommended that their concentrations be verified either by manufacturer recertification or by comparing the stated cylinder gas concentrations to a laboratory-based permeation tube-generated standard.

Dec 1, 2005

By Dana C. Reinke

Water well drillers are exposed to high levels of noise while working. NIOSH researchers have found that water well drillers are exposed to levels above 85dB (A) while performing certain tasks during a typical drilling job. Noise levels consistently over 85dB (A) during an 8–hour work shift are hazardous and can lead to hearing loss in workers. Finding ways to reduce noise exposure is difficult because of many factors. The work environment is constantly changing due to the location of jobs and environmental factors. The types of drill rigs required for drilling are expensive. Equipment can range from new to used (10 to 30+ years old). Drillers and owners can work together to prevent noise–induced hearing loss, and measures can be taken to reduce exposure to hazardous noise.[ ] Preventing hearing loss occurs through three stages. The first stage is removing noise from the source (i.e., drill rig). Various parts of a drill rig create noise besides the drilling rod. NIOSH researchers have examined noise levels of drill rigs. Some of the loudest parts of the drill rig include the compressor, engine, and cooling fan (Fig. 1). While removing the noise source from a worksite is ideal, the process would be expensive and difficult.[ ]

Jan 9, 2005

By Dana C. Reinke

Jan 1, 2005

By Fred N. Kissell

This handbook describes effective methods for the control of methane gas in mines and tunnels. It assumes the reader is familiar with mining. The first chapter covers facts about methane important to mine safety, such as the explosibility of gas mixtures. The second chapter covers methane sampling, which is crucial because many methane explosions have been attributed to sampling deficiencies. Subsequent chapters describe methane control methods for different kinds of mines and mining equipment, primarily for U.S. coal mines. These coal mine chapters include continuous miners and longwalls, including bleeders. Coal seam degasification is covered extensively. Other coal mine chapters deal with methane emission forecasting and predicting the excess gas from troublesome geologic features like faults. Additional coal chapters contain methane controls for shaft sinking and shaft filling, for surface highwall mines, and for coal storage silos. Major coal mine explosion disasters have always involved the combustion of coal dust, originally triggered by methane. Thus, a chapter is included on making coal dust inert so it cannot explode. Methane is surprisingly common in metal and nonmetal mines around the world, as well as in many tunnels as they are excavated. Accordingly, a chapter is included on metal and nonmetal mines and another on tunnels. Proper ventilation plays the major role in keeping mines free of hazardous methane accumulations. The ventilation discussed in this handbook, except for the chapter on bleeder systems, deals only with so-called face ventilation, i.e., ventilation of the immediate working face area, not ventilation of the mine as a whole. The omission of whole-mine ventilation was necessary to keep this handbook to a reasonable size and because a huge amount of excellent information is available on the subject.2

Jan 1, 2006