Search Documents

By Hsun Hu

Direct observations were made on the recrystalli-zntion of a cold-rolled (110) [001] crystal of 3 pct Si-Fe by annealing thin sections of the specimen inside the electron microscope during examination. Subgrain formation, presumably by polygonization, occurs rapidly, followed by a slow increase in the subgrain size before recrystallization can be detected. No migration of the subgrain boundaries was observed, and the formation of recrystallization nuclei by coalescence of subgrains is suggested. Re-c~ystallization characteristics of various texture components were individually examined. AS reported in a previous paper: orientations of the various deformation texture components in a 70 pct cold-rolled (110) [0011 crystal of 3 pct Si-Fe were completely confirmed by transmission electron diffraction patterns taken at various areas of the specimen. These orientations can be summarized as follows: Over most areas of the deformed crystal (111) planes are parallel to the surface. These areas correspond to either $- the two main defor: mation textures, the (111) [112] or the (111) [112].2-5 Within a few areas, (100) planes parallel to the surface are frequently found. These areas represent the minor deformation texture component, the (100) [Oll] type, which is derived from rotated Neumann bands.2'4'5 Only in very rare instances are (110) planes found parallel to the surface. This orientation corresponds to the very weak texture component of the (110) [001] type. In a pole figure, this (110) [0011 orientation is located within the orientation spread between the two main (111) [1121 type textures. Usually the electron diffraction patterns taken at various areas of the specimen are very simple ones, i.e., for any one area the pattern consists only of sharply defined spots of a single orientation. In some areas, however, more or less continuous rings of weaker intensities are superimposed on a simple pattern, indicating the presence of a wide range of additional orientations. In order to understand in detail the recrystallization of this cold-worked crystal, the recrywtallization characteristics of each of the various deformation texture components must be examined. This can best be done by using a high-temperature stage and transmission electron microscopy techniques, whereby small areas corresponding to the various texture components can be selected individually for examination. The present paper presents results obtained by this method. MATERIAL AND METHOD Specimens were prepared from a previously studied1 single crystal of a commercial grade 3 pct Si-Fe alloy with an initial orientation (110) [00l], cold-rolled 70 pct from 0.014 in. to 0.004 in. in thickness. Thin foils were prepared by electrolytic polishing as described in the earlier paper.' Specimens of this thin foil were then mounted in a high temperature stage similar to the one designed by Whelan.6 A direct current was used as the heating source. The temperature of the heating grid was calibrated by means of a Pt vs Pt-10 pct Rh thermocouple in a vacuum chamber (0.01 to 0.02µHg). Maximum variation within the temperature range of 250o to 000°C was about ± 25°C. After the desired areas were selected for examination, the specimen was heated to a low temperature for some time while the selected area was constantly watched. When no further change in structure and orientation could be observed, a higher temperature was applied. Photomicrographs and diffraction patterns were taken from time to time during examination, with the heater temporarily turned off* while the photographs were

Jan 1, 1962

By F. R. Morral, K. T. Aust

The preferred orientation and earing characteristics of ZS aluminum were studied. An empirical correlation was obtained relating earing behavior and variation of mechanical properties for face-centered cubic metals. Strain-ratio mecsurements for ZS were found to be in good agreement with Hill's theory of plastic anisotropy. DIRECTIONALITY in sheet metals may be revealed by earing in a cupping test, or by the variation of mechanical properties of tensile specimens taken at different angles to the rolling direction. However, no simple correlation appears to exist between earing and variation in mechanical properties in metals and alloys studied.1-5 Aluminum of commercial purity (known as 2S, with a specified minimum of 99.0 pct Al) cast by the direct casting process was chosen in the present investigation since ears at 45° or 0°, 90° can readily be obtained. Preferred orientation is often the principal cause of uneven metal flow, such as earing, and variation in mechanical properties. Consequently, the preferred orientation characteristics of 2s aluminum were initially studied using both X-ray diffraction and micrographic techniques. The variation of mechanical properties with angle to the rolling direction was next determined in an effort to clarify the apparent lack of correlation of earing behavior with mechanical properties for face-centered cubic metals. Strain-ratio*5,8 measurements were finally conducted to determine first, if the maximum values of the strain ratio occurred at the earing positions, and second, if Hill's theory of plastic anisotropy7 is applicable to other face-centered cubic metals such as aluminum. Detailed treatments, working, and heat treating are not given in this paper since this study is not concerned with the methods to produce earing, but to correlate earing with other properties and characteristics of the material. The percentage of earing was measured using the formula specified by the x—Y Aluminum Association, -------- X 100 = pct earing, where x is the height of the ear and y is the height of the valley from the bottom of the cup. Preferred Orientation Characteristics of 2S X-ray Studies: Beck and coworkers8 have determined that the rolling texture of 2s after 95 pct cold reduction may be approximately described by four equivalent ideal orientations near (123) [121]. Also, the recrystallization or annealing texture of 2s aluminum consists of four components of the (123) [l21] type, retained from the rolling texture, and of a (100) [001] or cube texture component." Fig. 1 illustrates the typical appearance of deep drawn earing cups with the corresponding X-ray diffraction patterns. The X-ray patterns were taken with copper radiation using the structure-integrating method'" in which the specimen is scanned during the X-ray exposure. The rolling direction was vertical and the rolling plane was perpendicular to the horizontal X-ray beam. It was found that an increase in the retained rolling texture component resulted in a greater 45" ear height, while an increase in the recrystallization texture component (i.e., cube texture) caused greater 0°, 90° earing. X-ray diffraction studies of 2s cold rolled to final thickness followed by a final anneal have shown that the rolling texture, and also the retained component of the rolling texture after annealing, are increased with greater cold-rolling reduction. The preferred orientation characteristics of 2s sheets given an intermediate anneal between cold rolling followed by a final anneal were found to depend on the position of the intermediate anneal during cold rolling. For instance, three identical samples of 2s homogenized ingot, each 1 in. thick, were given the following cold-rolling and annealing treatments: 1—50 pct reduction, intermediate anneal, 96 pct reduction to 0.020 in. and a final anneal; 2—75 pct reduction, intermediate anneal, 92 pct reduction to 0.020 in. and a final anneal; and 3—90 pct reduction, intermediate anneal, 80 pct reduction to 0.020 in. and a final anneal. The intermediate and final annealing treatments consisted of a 70°F per hr heating rate, held 6 hr at 800°F and air cooled. Typical X-ray patterns after each of these treatments are shown in Fig. 2. It was evident that after treatment 1, the retained rolling texture component predominated; after treatment 2, the retained roll-

Jan 1, 1954

By A. R. Troiano, E. A. Steigerwald, F. W. Schaller

The kinetics of crack propagation in a hydrogenated high-strength steel at subzero temperatures indicated that cracking progressed in a discontinuous fashion. The delayed failure process thus involves a series of crack initiations rather than the continuous growth of a single crack. The incubation time required for the initiation of delayed failure was controlled by the diffusion of hydrogen. The activation energy for the process was 9120 cal per g-alom. As the test temperature was lowered the incubation time constituted a greater percentage of the total tinze to fracture, and al -50°F the incubation and fracture times were essentially coincident resulting in instantaneous, catastroplzic fracture. A unique feature of hydrogen embrittlement is the delayed failure process in which the material fails under the action of a sustained load even though it is capable of supporting a higher load for a finite period of time.')' Delayed failure of steel and titanium is characterized by an incubation time, preceding the initiation of a crack in a highly localized region, and the subsequent growth of the crack to ultimate failure.3-5 The kinetics of crack growth in hydro-genated high-strength steels have been studied through the use of resistance measurements and have an important bearing on the mechanism of delayed failure. Delayed failure is believed to be merely a facet of hydrogen embrittlement in which sufficient time is allowed during a test for hydrogen diffusion. The current theories employed to explain hydrogen em-brittlement can be grouped into two types. one6-8 explains the embrittlement on the basis of the pressure exerted by molecular hdrogen in lattice voids or defects while the other9-10 attributes the embrittlement to the influence of hydrogen in the lattice. The mechanism used to explain the nature of the crack kinetics in delayed failure is based on the stress-induced diffusion of hydrogen to the area of maximum triaxiality.3 When the hydrogen concentration in this region reaches a critical value, a crack is nucleated. This initial crack propagates instantaneously until stopped by the higher fracture stress of the adjacent material of lower hydrogen content. The continuation of cracking must then await the further diffusion of hydrogen to the new region of triaxiality near the base of the crack where another initiation will occur. From this mechanism it follows that crack propagation is nothing more or less than a series of initiations with limited fracture. The purpose of this investigation was to examine the kinetics of crack growth in an effort to determine whether or not the process was discontinuous. Studies of crack propagation were conducted at low temperatures to retard the diffusion of hydrogen which is presumed to be the rate controlling process in delayed failure. MATERIALS AND PROCEDURE Specimen Preparation—A commercial heat of air-craft quality SAE-AISI 4340 steel, designated as Heat G, was furnished by the Republic Steel Co. in the form of %-in. hot-rolled bars. The material had the following chemical analysis: Composition of 4340 Steel—G Heat C Mn Si Ni Cr Mo 0,395pct 0.82pct 0.29pct 1.76pct 0.85pct 0.25pct Notched tensile specimens with less than a 0.001 in. radius, Fig. 1, were used throughout the investigation. The specimens were heat treated to a 230,000 psi strength level according to the following sequence: a) Normalize bar stock at 1650°F for 1 hr, b) Stress relieve at 1200°F for 4 hr and furnace cool,

Jan 1, 1960

By L. D. Jaffe, H. C. Mann, E. L. Reed

The authors have recently published1 evidence that brittle transgranular fracture of polycrystalline metals does not originate at a point and propagate continuously across the material, but rather develops at numerous related points, leading to a series of micro-cracks which subsequently link up. Series of related microcracks were observed in steel specimens broken in fatigue—specifically, at the central portions which broke during the final sudden fracture. Microcracks of the type mentioned have also been reported by Baeyertz, Craig and Bumps'2 in steel broken under impact. % Some micrographs published by Irwin3 may possibly be interpreted as showing discontinuous brittle cracks. This paper presents additional observations of the authors on discontinuous crack propagation under various conditions. Impact Test Specimens The impact test specimens were cut longitudinally from a steel forging containing: The heat treatment consisted of oil quenching in a heavy section from 1600°F and tempering at 1260°F. The resulting yield strength was 78,000 psi, tensile strength 100,000 psi, elongation 20.0 pet in 2 in., and reduction of area 55.0 pet. Standard V-notch Charpy specimens were broken in a 217 ft-lb machine at a striking velocity of 16.8 fps. Energy absorption and fracture appearance of this material in the V-notch Charpy test are plotted as functions of temperature in Fig 1. After test, fractured halves of specimens appearing 0, 40, 80, and 100 pet fibrous (to the unaided eye) were electroplated with nickel, sectioned longitudinally (perpendicular to the notch at its midpoint), polished and etched with Cohen-Hurlich-Jacobson (C-H-J) reagent (picric acid plus Zephiran chloride in ethyl ether)4 or with Vilella reagent (1 pet picric plus 5 pct hydrochloric acid in ethyl alcohol).5 Fig 2 and 3 show cracks near the path of final fracture in the specimen rated 0 pct fibrous. Many of the cracks terminate at the boundaries of ferrite grains, some at boundaries of pre- existing austenite gzains. * A crack often starts near the end of another. Cracks within the same ferrite grains are parallel or approximately parallel in several cases. A large percentage of the cracks are branched. Fig 4 illustrated a group of cracks in the 40 pct fibrous specimen. Branching and parallelism are well marked. No more than three directions of crack have been observed on the polished surface in one ferrite grain. This is consistent with the evidence6 that brittle fracture of ferrite takes place on the cube face crystallographic planes: the {100} planes. The appearance of some cracks suggests that they have passed around a projecting corner of a second ferrite grain by going outside the plane of polish. In Fig 5 cracks in the 80 pet fibrous specimen may be observed. Some of

Jan 1, 1950

By I. R. Kramer

In his technical note entitled "Specimen Temperature During Electropolishing of Aluminum Crystals" Dr. Nakada 1 reported that the temperature of his aluminum specimen increased 65°C when it was polished electrolytically; he therefore concluded that the temperature of the specimens used in our work (Nakada's Refs. 4 and 5) similarly increased by this amount. From this he further concluded that the change in plastic-flow characteristics associated with the removal of the surface by electropolishing during deformation were due solely to a temperature effect. We believe that these conclusions are not justified. It is, of course, realized that the amount of the temperature increase is associated with the total heat transfer of the entire system, including the efficiency of the stirring action, heat flow through the grip on the specimen, and so forth. Of great importance is the type of electrolyte used for polishing. For example, in Dr. Nakada's experiment a methanol-perchloric acid solution was used. This solution has a relatively low conductivity and for the current densities of 0.3 amp per sq cm the electrical input appears to be 30 to 40 w. In our research a methanol-nitric acid solution was employed and for the size of specimen employed by Dr. Nakada the power never exceeded 7 w. There are major differences in his test apparatus which also appear to affect the temperature rise. In our case a steel specimen holder was used in order to provide a good heat sink and conduction path. The cathode was a coiled aluminum tube through which a coolant was passed to provide additional cooling capacity near the specimen. The stirrer was placed in a position to obtain maximum cooling efficiency. On the other hand Dr. Nakada used a teflon grip to support the specimen at one end only and a flat copper cathode, thus providing a much less efficient heat sink as compared with the metal grips used in our studies. The relationship between current density and the temperature increase for two sizes of aluminum crystals tested in our tensile apparatus is shown in Fig. 1. The temperature measurements were determined from a thermocouple spot-welded to the surface of the specimen. The thermocouple was protected from the acid by means of a thin film of stop-off lacquer which covered just the outer surface of the thermocouple junction. Whereas Dr. Nakada reported a time delay of 8 min to obtain thermal equilibrium, our temperature change occurred in less than 15 sec. This emphasizes the importance of the heat transfer in the entire system. However, readings were taken over a period in excess of 5 min to assure thermal equilibrium. The data given in Fig. 1 were also confirmed by determining the thermal expansion of the specimen in a sensitive creep apparatus. As may be seen, for the smaller specimen the increase in temperature is 8°C for a current density of 1.5 amp per sq in. The majority of our data on the effects of surface removal on the plastic behavior of aluminum were obtained at current-density values at or below this value. Above 1.5 amp per sq in. the temperature rise is uncertain; for under certain conditions, especially in the vicinity of 2 amp per sq in., the anode can become polarized and the current flow is erratic. This condition is easily recognized because wide fluctuations in the creep and stress-strain data make it virtually impossible to obtain reliable results, a condition which was always avoided in our work. The temperature increase for the larger specimen is less than that of the smaller specimens below a current density of 1.5 amp per sq in. At a current density of 2 amp per sq in. the temperature increased 13°C. The above temperature data are in accord with observations made during creep experiments. Using a transducer capable of detecting strain in the order of 10 -6, temperature changes in excess of 8°C were not detected when the current density was increased to as high a value as 1.5 amp per sq in. Finally we wish to point out that our experimental data cannot be explained solely in terms of a heat effect. For example in Fig. 1 of Ref. 2, the change in slope of Stage II as a function of the rate of re-

Jan 1, 1965

By G. N. Maniar

G. W. Healy (union Carbide Metals Co.)-The author's paper is a useful contribution to the store of maps of chemical activities of oxides in multi-component slag systems. It is also a good example of the utility of the Gibbs-Schuhmann technique for calculating activities in a system where that of one of the components has been measured. This paper Koh and Caugherty. This plot is reproduced by alor in X-ray Metallography. Because of this nonlinearity, preparation cf suitable standards and/or correction for absorption and enhancement are essential in microanalysis. However, our objection is not the conclusion that Dr. Aaronson has arrived at nor the technique he has used; but only to the foot-note credited to V. Macres. The level of chromium that he was concerned with (less than 3 pet) is so low that the deviation of uncorrected Cr-curve will be negligible. Besides Dr. Aaronson has used chromium intensity from martensite and set it equal the bulk chromium content of the alloy. Using this chromium-intensity as a reference, he has calculated the amount of chromium in the ferrite. This amounts to the same as using an internal standard. Since the chromium content in austenite and ferrite are almost the same, enhancement due to iron in both will be the same and therefore does not need to be corrected. together with the author's recently published one1 on the CaO-FeO-Fezo3 system will be most helpful to others learning to apply Schuhmann's method, which merits a far wider application than it has received to date and should greatly aid our understanding of equilibria between metal and oxide phases. As shown by okcen" its use may even be extended to sections of systems with any number of oxides. I have some questions as to the selection of equilibrium constants made by Dr. Turkdogan. He has chosen one for the formation of Fe2O3 from FeO and oxygen which gives Fea3 activities 50 pct higher

Jan 1, 1963

By S. J. Rothman, L. T. Lloyd

S. J. Rothman and L. T. Lloyd (Argonne National Laboratory)— Hagel's paperz0 discusses the question of the mechanism for self-diffusion in bcc transition metals. Recent work21"23 has led us to agree with him in reabandoning the ring mechanism in favor of a defect mechanism, most likely vacancies. On the other hand, we think that Hagel's attempt to group together all self-diffusion in bcc transition metals is wrong. We prefer the scheme of Peart, Graham, and omlin," who separate them into two groups. One group contains the anomalously behaved metals P titanium,', y uranium, and perhaps zirconim.' The other group contains a iron," this alloy was held at 1800°C for 2 hr before quenching, its structure was all a. B. C. Giessen, I. Rump, and N. J. Grant (Authors' reply)—We very much appreciate the discussion by Deardorff and Kato regarding the a to /3 transformation temperature of hafnium. In the W-Hf program, as well as in a current study of the system Cr-Hf, standard precautions were exercised against contamination, including vacua of less than 10"5 mm Hg and a weight control check of all specimens to insure an impurity rise of less than 100 ppm. Following receipt of the above discussion, a revision was made in the annealing process. Arc-cast specimens were etched with a 10 pct HF-90 pct HNO solution until 1 mm of surface, including a possible oxide film, was removed. Annealing was done in a hafnium container which provided a long diffusion path for gaseous contaminants. Finally, the heat treating time was shortened. Structural changes were noted to occur quite slowly. A 99.5 at. pct Hf alloy showed 70 pct /3 after 30 min at 1700°C and was 100 pct /3 after 10 min at 1715°C. After 24 hr at 1740C, the alloy was found to be 10 pct/3. This change is due to contamination; it was estimated that it corresponds to an increase of 60°C in the transformation temperature over a 24 hr period. The corresponding change in 30 rnin would be slight. Using the same hafnium as in the above publication, and three new alloys at 98, 99, and 99.5 at. pct Hf, the transformation temperature was indicated to be 1715" 15°C. Since this hafnium contained 4.4 at. pct Zr, a correction of 40 5C, based on an assumed approximately linear transformation temperature curve, must be made for pure hafnium. This yields a value of 1755 20°C in good agreement with Deardorff and Kato's value. Because the slope of the boundary is small, this permits a good extrapolation, and we regard the W-Hf alloys as well suited to check the Hf transformation temperature. niobirn,'' and molybdenum,22 whose activation energies correlate with the melting temperature and whose Do values follow Zener's predictions.28 We have no quarrel with Hagel's placing chromium into the second group; we disagree with his interpreting our data to make uranium fit into that group. Hagel considers that the measurements of self-diffusion in uranium below about 950°C represent combined volume and grain boundary diffusion. This contention is based on the curvature of the penetration plot for our 891°C run,4 which also has a nearly straight line plot of log c vs x. Hagel has extrapolated these characteristics to our 803.5C run and fitted his Arrhenius plot for self-diffusion in y uranium to our four highest temperature points only. We think this is wrong for the following reasons.

Jan 1, 1963

By D. K. Deardorff, Haruo Kato

D. K. Deardorff and Haruo Kato (U. S. Bureau of Mines)—We wish to refute the 1875" 20°C value that Giessen, et al., report as the transformation temperature of hafnium. Although these authors state that their work along this line will be reported later, we can't leave their value undiscussed, for we believe it to be 125°C too high. Our value of 1750° 20°C, which the authors mention, has been substantiated in our laboratories by the use of three other methods. The first method of substantiation was by heating and cooling curves using a hafnium/tungsten thermocouple, the couple having first been calibrated against a t/Pt-10 pct Rh couple. The second method was by quenching and metallography of dilute Hf-Ta alloys. The third cussion, it may be pointed out that the observations of Rogers referred to large unidirectional strains where the internal cracks or voids appeared only after a strain of 32 pct or more. On the contrary the internal fissures observed, as a result of fatigue cycling, occurred for a total extension of some 5 pct and furthermore followed the directions of the slip zones. Finally, it is not our contention, as implied in Dr. Alden's last paragraph, that the tensile stress is an important factor in crack propagation. Indeed, in connection with the reference to the companion report, special note is made of the fact that "Deformation was apparently concentrated in grains which have a slip plane nearly perpendicular to the specimen axis and thus near the plane of maximum applied shear." This dependence of the growth of fissures on the orientation of the slip planes with respect to the direction of maximum applied shear is clearly shown in work on the torsional cycling of single crystals which has been submitted for publication. method was by heating and cooling curves with W/W-26 pct Re thermocouple. Counting the original resistometric method, four different methods have yielded 1750" 20°C as the transformation temperature of hafnium. All our work on determination of the hafnium transformation temperature has shown that the specimen under test must be quickly heated to and through the transformation temperature if the lowest possible transformation value is to be determined; otherwise a higher value not representative of pure hafnium will result. Speed was emphasized in all methods. In our resistometric work the corresponding voltage, amperage, and temperature readings were taken quickly and the transformation temperature was usually reached within 5 min total heating time. In the thermal analysis work involving Hf/W or W/W-26 pct Re thermocouples the transformation temperature was attained within three minutes total heating time, this time being less because the two variables were

Jan 1, 1963

By T. S. Lundy, J. Askill

J. Askill and T. S. Lundy (Oak Ridge National Laboratory)—Moore has proposed a simple correlation between the activation energy for solute diffusion in fee metals and the atomic volume of the diffusing species using both tracer and chemical-diffusion data. The first point we wish to make is that it is wrong to attempt such correlations without separating the two types of data. Activation energies obtained using tracer techniques cannot, in general, be directly compared with those obtained from chemical-diffusion experiments. A knowledge of the variations of chemical potentials with composition is necessary and chemical-diffusion data must be corrected for such variations, even for dilute alloys, before a comparison is possible. Secondly, for nickel, iron, aluminum, and lead, Moore neglected a number of recently published works, e.g., Al26 and Mn54 in aluminum,46 cr51 in nickel,47 and Fe55 in iron.48 These and others should have been used. If one considers only the tracer diffusion data, there is left no simple correlation of the type proposed by Moore. For example, in the case of solute diffusion in aluminum the only reliable tracer data listed by Moore are for zinc and aluminum. The nickel, cobalt, and iron data of Agarwala49 are representative of near-surface diffusion-not bulk diffusion. In conclusion we suggest that for tracer diffusion data in these fee metals there is no justification for proposing any simple correlation of activation energy with atomic volume using the limited data that are presently available. R. H. Moore (author's reply)—The writer has proposed a simple correlation which is useful in estimating the internal consistency of diffusion data. The accuracy of the correlation is, of course, a function of the number of data available. Lundy and Askill take issue with the writer's decision to include data for the systems: nickel, iron, aluminum, and lead, taking the view that the data are insufficient to establish the correlation. The writer agrees that the data are insufficient and has cau- tioned the reader that the correlation is tentative in these instances. Inclusion of these systems is justified by the interesting trends the correlation reveals. For example, the distinction between interstitial and substitutional diffusion may be clearly established, Figs. 4 and 6, and the behavior of transition elements and nontransition elements is indicated to parallel the behavior illustrated by the silver and copper systems. Lundy and Askill have singled out the aluminum system for special criticism. The writer chose to discuss the data for diffusion of iron, nickel, and cobalt in aluminum in the terms used by the original authors9 and has included the comments of Balluffi.l0 The writer did not intend the reader to conclude that data for these elements should correlate with data for the nontransition elements as Lundy and Askill have evidently assumed. Iron, nickel, and cobalt form intermetallic compounds with aluminum, so the activity coefficients of these elements may be expected to deviate markedly from unity. This may account for the low frequency factors observed by Hirano.9 The nontransition elements, on the other hand, yield relatively simple phase diagrams with no evidence for intermetallic compound formation as in the case of iron, nickel, and cobalt. In dilute solution, Henry's law should be closely obeyed, the activity coefficients should not deviate markedly from unity, and the effect on the activation energy should not be large. The accuracy of the correlation applied to these systems will improve as the data is extended. It does not seem unreasonable to conclude that its extension should be encouraged.

Jan 1, 1965

By R. I. Jaffee, R. W. Wood, H. R. Ogden, D. N. Williams

D. W. Morgan, D. H. Polonis,and R Taggart (Uuivevsity of Washington)—Dispersion hardening in titanium-copper alloys is of particular interest to us in view of our current research activities in phase transformations in this system. We should like to raise questions concerning several points in the paper. The flow sheet for fabrication and heat treatment (Authors' Fig. 2) indicates that 0.045 in sheet is treated in air for a period of 30 min at 1625' F. Were any surface coatings used to reduce oxygen contamination at this stage? One might ask the same question about the 8-hr annealing at 1400F. Contamination during fabrication and heat treatment of such thin sections could be considerable without some protection. Although the authors state that no analyses were made, they note that contamination masks the distinction between base strengths of the different alloys. In this connection, what fabrication and heat-treatment procedures were used in obtaining the comparison specimens of unalloyed titanium? It would seem that oxygen contamination must cast doubt on the reliability of the proposed strength-mean free path relationship deduced from the data (Authors' Fig. 5). It is usual to evaluate dispersion hardening on the basis of yield strength rather than ultimate tensile strength, and accordingly we have replotted the authors' Fig. 1 to include yield strength. The yield strength data do not justify a discontinuity of 3 p at either 70" or 1000 OF. Can the authors substantiate their conclusion 1) with additional evidence? Otherwise it seems that they have succeeded only in pointing out the possibility of a linear relationship between yield strength (or Uts) and the logarithm of the nleall free path, comparable with that demonstrated for iron-carbon alloys (Authors' Ref. 2). Work in our own laboratories has shown that the hardness of the phase Ti,Cu is 235 Vpn, and that of a 1.5 pct (at.) (2 pct wt) supersaturated solid solution of copper in titanium is 190 Vpn. This small difference in hardness would suggest that Ti2Cu should not be a very effective dispersion-hardening phase. D. N. Williams, R. W. Wood, H. R Ogden, RI. L Jaffee (authors' reply)— This discussion brings out some interesting points with respect to the interpretation of our results, and also raises some questions regarding the experimental technique. We shall consider the latter questions first. Contamination during heat treatment was prevented by performing all heat treatments in argon-filled Vycor capsules. Fabrication was done in air, with the usually observed scaling. Scale was removed

Jan 1, 1962

By I. R. Kramer

I. R. Kramer (Martin Co.)—In a recent paper Nakada and Chalmers24 reported some observations of effects of surface conditions on the stress-strain curves of aluminum and gold single crystals. It is of interest to compare these observations with the results published previously in this journal and to comment on their general conclusions. In brief, Nakada and Chalmers concluded that the removal of the surface layer of a prestrained specimen lowered the stress-strain curve for aluminum but not that for gold. Further, they concluded that the surface work hardening of aluminum is confined to a depth not more than l0-3 cm. In our results25 published previously, it was pointed out that when prestrained specimens of aluminum and gold were polished to reduce the thickness upon reloading the initial flow stress decreased markedly. Further if a sufficient amount of metal was removed, the yield point failed to appear. With continued application of the load the stress-strain curve became coincident with that of the virgin crystal. We have found this behavior in some 100 determinations to hold consistently for gold, aluminum, and copper in both single and poly-crystalline specimens. The amount of strain required before the curves coincided depends upon the amount of metal removed but it is usually less than 0.01. This type of behavior is the same as that reported for metarecovery by other investigators.29 For aluminum specimens which have been prestrained and then heated to temperatures above 50°C we have consistently found that the stress-strain curve was typical of the orthorecovery28 type. In this case the stress-strain curve always lies below that of the virgin specimen. With respect to Ref. 24 the curves for aluminum are always below that of the virgin curves, while those for gold become coincident. This observation indicates at least for aluminum that the specimens must have been heated to a temperature high enough to cause recovery by an alteration of the internal dislocations. In addition, a recovery would be expected because of the removal of the surface work-hardened layer. Nakada27 had reported that, with his particular apparatus in which a perchloric acid polishing solution was used, the temperature of the specimen increased 65°C. The curves presented in Ref. 24 for gold do not permit one to detect the initial flow stress upon reloading after the surface-removal treatment. In fact, contrary to the method used by Nakada and Chalmers, the change in the stress-strain curve produced by a surface-removal treatment cannot be described in terms of a decrease in stress at strains much higher than that at the initial flow stress because of the coincidence of the curves at the higher strain values. With regard to the depth of the work-hardened surface layer, our data show for aluminum single crystals (7.5 by 0.3 by 0.3 cm) that the initial flow stress remained constant after 12 x 10-3 cm had been removed from the thickness. This depth was independent of the prior strain. For gold crystals this depth is somewhere between 10 x 10-3 and 20 x 10-3 cm. Y. Nakada (author's reply)— Kramer states,28 "for aluminum specimens which have been prestrained and then heated to temperatures above 50°C, we have consistently found that the stress-strain curve was typical of the orthorecovery28 type. In this case the stress-strain curve always lies below that of the virgin specimen." However, Cherian et a1.26 discovered that aluminum polycrystals annealed at 32" and 100°C showed the metarecovery behavior. They showed that the orthorecovery behavior did not appear until the crystals were annealed at 150°C. Kramer suggests28 that the drop in the flow stress of aluminum crystals after the surface removal by electropolishing24 may be due to the recovery caused by the temperature rise which may occur during the electropolishing.27 However, as indirectly stated in Ref. 24, the current density used in these electro -polishing experiments was 0.15 amp per sq cm. According to ref. 27, this current density should cause a temperature rise of only 40°C. This may cause the metarecovery but not the orthorecovery. Furthermore, as stated explicitly in Ref. 24, the surface removal was accomplished by chemical etching as well as by electropolishing. The results were the same for both electropolishing and etching. During the etching, the specimen temperature did not rise above 35°C. Some aluminum crystals were placed in water at 35° C for 30 min. These crystals did not show the decrease in flow stress. Therefore, it is quite clear that the flow-stress drop after the surface removal is not caused by a high-temperature recovery. However, as Kramer points out,28 it is quite possible that the internal dislocation structure may have been altered because of the removal of the highly work-hardened surface layer. However, how much this rearrangement contributes toward the flow-stress decrease is not known at present.

Jan 1, 1965

By M. van Swaay, C. E. Birchenall

A. S. lBrling (Johnson, Matthey & Co. Ltd., Laboratories)— Because of its initial emphasis upon the production of membranes by powder metallurgy and by normal casting and rolling techniques, this paper is of considerable interest to those concerned with the design and application of industrial diffusion units. As the subsequent performances of the three grades of palladium were not compared in detail, it can perhaps be concluded that specific permeabilities were very similar. A short table in which the absolute diffusion rates obtained by the Authors with their three grades of palladium were compared with those of other investigators18-25 would, however, have been of particular value in view of the very variable results obtained with this membrane material. The Authors state early in the paper that the permeability of the thoriated samples decreased in much the same way as that of the nonthoriated samples. Later, they emphasize that sintered palladium without thoria was very susceptible to poisoning and did not respond as well as the other materials to the decontamination treatment. These results, which suggest that sintered membranes are less effective than those produced by normal methods, have considerable industrial implications, and amplified experimental details would be very welcome. The results of the Authors differ in one important respect from those of other investigators. Thus, no "bleeding" was required to maintain a constant rate of diffusion, although Davis, Darling, and De Rosset found this to be necessary. Davisz3 found that "bleeding" was necessary even when the hydrogen had already been purified by diffusion through a palladium tube, and it would be of value to know the purity of the gas stream emerging from the purification train shown on Fig. 1 of the Authors' paper. The Authors show that diffusion rates varied according to the square root of the pressure difference providing that the palladium membrane was not contaminated in any way. This finding is in agreement with the results of those workers2,18,19,23,24 who diffused their hydrogen through the membrane into a partly or completely evacuated system.Those workers who did not find this square-root law dependence did not have a partial vacuum on the downstream-side of the membrane.'' The difference between the two experimental con- ditions appears to be significant, as the absolute diffusion rates per sq cm of diffusion area are lower when the square-root law dependence is not observed. While the effect could be attributable to poisoning of the membrane it is conceivable that a positive pressure on the downstream side of the membrane might influence the mechanism of diffusion. In view of the capricious behavior of palladium, factors of this type, which are likely to influence its industrial significance, should be carefully considered. M. van Swaay and C. E. Birchenall (authors' 9-eply) — Our Eq. 191 may be compared with several others for hydrogen diffusion in palladium: D = 5.95 x exp (-5770/1)' D = 3.55 x 10"3 exp (-5550/)' D = 4.3 x 10"3 exp (-5620/1')' Other values are given in the literature, but in many cases surface poisoning may have affected the results. No analysis was performed on the hydrogen gas stream after purification. It should be noted that the presence of liquid nitrogen traps near the heated membranes may have set up convection currents and provided the equivalent of "bleeding." The question of whether a partial vacuum existed on the downstream side of the membrane is not clear. Does it imply that there is something unique about the permeability measured near one atmosphere pressure? We do not believe that there is. When square root pressure dependence is not observed, diffusion rates are not measured. Is "absolute diffusion rate per sq. cm. of diffusion area" equivalent to permeability? The terminology is new to us. In any case we doubt very much that pressures of the order of several atmospheres can affect the mechanism of diffusion.

Jan 1, 1962

By W. Bonfield

A study has been made of the dislocation substructures produced in hot-pressed beryllium specimens strained to various levels in the range from 800 x 10-6 In. pev in. to fracture. A number of distinctive dislocation configurations were observed in this region which had not been noted at lower levels of strain. These included dislocation-dislocation interactions to form networks, dislocation "walls", subgrain boundaries and complex arrays, interactions between dislocations and large beryllium oxide particles, and the generation of dislocations from certain particles. The nature of these differences in substructure and their relation to the stress-strain characteristics of polycrystalline beryllium are discussed. In a previous study1 of the plasticity of commercial-purity, hot-pressed beryllium a transition was found in the deformation characteristics in the mi-crostrain region. The initial plastic deformation could be represented by a parabolic stress-strain equation, but above a critical stress there was a complete departure from this relation and a reduction in the strain-hardening rate. The dislocation configurations produced by various levels of micro-strain in this region were examined by transmission electron microscopy and a general correlation was established between the observed transition in deformation characteristics and the dislocation structure of the material. The two stages in the micro-strain region distinguished in these experiments were designated as Stage A' and Stage B'. Stage A' type deformation generally was noted up to a plastic strain of -80 x 10"6 in. per in. and Stage B' type from -80 x 10-6 to -800 x 10'6 in. per in. The discovery of two stages in the microstrain region naturally posed pertinent questions as to the existence of any further distinct stages in the subsequent plastic deformation. The purpose of this paper is to present a study of the dislocation configurations produced in similar beryllium specimens strained to various levels in the range from -800 x 10 in. per in. to fracture and to discuss the relation between substructure and the stress-strain characteristics. It is concluded that this region of strain can be considered as a distinct stage in the plastic deformation of polycrystalline beryllium. Tensile specimens of gage length 1 in. and cross section 0.18 by 0.06 in. were prepared from commercial-purity, hot-pressed QMV beryllium and then annealed at 1100°C for 2 hr. 2 followed by a careful chemical polishing procedure.3 The specimens were strained at a constant rate to various levels of strain in the range from -800 x 10-6 in. per in. to fracture (at 0.5 to 2 pct elongation), using the Tuckerman strain-gage technique1 to measure plastic and total strain. Thin foils were obtained from the strained and fractured specimens by chemical polishing3 and were examined using an RCA-EMU 3 electron microscope. Considerable care waS taken to avoid both accidental deformation during the preparation of the thin foils and excessive heating during their examination. Selected-area diffraction patterns were determined for each micrograph. Tilting experiments were also performed whenever appropriate to establish the dislocation zero-contrast position and hence determine the Burgers vector. This operation was sometimes not possible due to the rapid contamination of the foils which occurred in the electron microscope. RESULTS AND DISCUSSION To enable the distinctions between the dislocation arrays at high and low strain levels to be adequately made, the main characteristics of Stage A' and Stage B' deformation are briefly reviewed. 1) Stage A'. In the annealed starting condition there was a variable density (5 x 107 to 3 x 10' cm per cu cm) of isolated dislocations within a grain. The initial deformation in a tensile specimen was heterogeneous, with the dislocation density increasing in a few grains to 5 x 10g to 1.5 x 101° cm per cu cm. The deformation occurred exclusively on the basal plane by the movement of one or more 1/3 (1130) type dislocation systems. The dislocations were long and regular in form and nearly all the intersections exhibited a simple four-point node configuration. No interactions between glide dislocations and beryllium oxide particles were observed. 2) Stage B. In Stage B' there was a large increase in the number of grains exhibiting dislocation movement and also a change in the nature of the deformation, in which jogged dislocations and elongated loops became the characteristic feature. The splitting up of the elongated loops into smaller loops and the possibility of source action from the re-

Jan 1, 1965

By K. R. Janowski, H. Conrad

As part of a program to establish the effect of crystal imperfections on laser output, a detailed study was made of the dislocation structure of ruby crystals obtained from varioius sources. Using KHSO4 as an etchant, a detailed mapping of the dislocation structure on the (0001) and the (1150) planes was carried out. A less extensive study was made of the rhombohedral planes. The average dislocation density on the basal plane was 1.5 to 3 x 106 cm&apos;2 and on the (1120) planes -5 x 10&apos; cm-2. Howe7!er, considerable variation existed between areas on a given plane. The subboundaries in the basal plane tended to lie along [1100] type directions while those on the (1120) plane tended to lie: a) parallel to the basal plane, b) along truces of the (1101) plane, and c) along normals to the traces of the (0001) planes. The orientations suggest that mang of the dislocations lie on the (0001), (1701), and (1150) planes A Laue back-rellection nnalysis Of c-axis wander in one crystal revealed a gradual increase in misorientation from me end of the crystal to the other, with a maximum variation of 1°35&apos;. Slight etching of a mechanically polished crystal revealed mumerous polishing scratches, suggesting the existence of a plastic flow layer. It is recognized that chromium concentration, lineage, and other crystalline imperfections play a role in the efficiency of ruby lasers.&apos; Consequently, it is desirable to establish in detail the imperfection structure of ruby crystals to be used as lasers. Some exploratory work along this line had already been done by Barnes&apos; and Dils and Martin.&apos;" How- referred to as the morphological system, as described by Kronberg.4 The Miller indices given in the present paper will be based on this morphological system. In this system, the three common growth planes are the (0001), the {1120}, and the {1101}.5 Since these planes are of high stability, it is expected that they are most suitable for study by the etch-pit technique. In the present investigation, a detailed mapping of the dislocation structure was carried out for the (0001) and the (1130) planes. A less extensive study was made of the etch-pit structure on rhombohedra1 planes. An analysis of dislocations in sapphire (the ruby host) was first made by kronberg,4 who postulated that slip on the (0001) plane occurred by motion of dislocations with Burgers vector 1/3 <1150> and that these dislocations might dissociate into quarter partials. An etch-pit technique using boiling phosphoric acid was developed by Scheuplein and Gibbs6, 7 for identifying dislocations intersecting the (0001) planes and the planes near (2021) in sapphire. Al-ford and Stephens8 were able to reveal dislocations on the (0001) and {1120} planes in sapphire and ruby by etching in fused potassium bisulfate (KHS04) at 675°C. The termini of basal dislocations [(000l), <1120>] were revealed by Palmour and Kriegel9 on {1120} and {1010} by thermally etching sapphire. Bond and Harvey10 were able to decorate dislocations in sapphire by adding 1 pet by weight of ZrO2 to the Al2O3 powder used in the growth of the crystals by the Verneuil technique and then heating the grown crystals for 4 hr at 1500°C. They found, using optical transmission microscopy, that many dislocations had straight segments which were parallel to one of the six [1120] directions in the basal plane. Single dislocation lines curved smoothly from one alignment to the other, turning through angles of 60 to 120 deg. Also observed were isolated hexagonal loops, approximately 10 µ in diameter, the sides of which lay along the same directions as did the longer dislocations. MATERIAL AND ETCHING PROCEDURE The ruby specimens used in this study (all containing approximately 0.04 pet Cr) had been obtained from four different sources: Linde Co., Meller Co., Valpey Crystal Corp., and those grown at Aerospace Corp.* For the initial phase of this study, several specimens were cut from the slab shown schematically in Fig. 1 which had previously been cut from a disk boule obtained from the Linde

Jan 1, 1964

By E. W. Hart, W. R. Hibbard

The room temperature flow characteristics of a series of Cu-Cr alloys are found to be related to the amount and characteristics of the chromium-rich precipitate. The results are consistent with the theory of Fisher, Hart, and Pry, which considers the trapping to dislocation loops around precipitate particles. THE use of dispersed phases for hardening metals, particularly high temperature alloys, has been practiced for several years. Current theories describing the effects of dispersions on the basis of dislocation theory have been proposed by Mott and Nabarro.l-4 rowan," and Fisher, Hart, and Pry.8 These theories recently have been discussed by Hart,&apos; who pointed out that the experimental data available for comparison with theoretical calculations for overaged alloys are confined to studies by Gensamer, Pearsall, Pellini, and Low,8 Shaw, Sher-by, Starr, and Dorn,9 and some hitherto unpublished data on Cu-Cr alloys which will be described herein. Certain difficulties were associated with the interpretation of the first two studies. Gensamer, Pearsall, Pellini, and Low were concerned principally with interparticle spacing and did not document particle sizes. Shaw, Sherby, Starr, and Dorn included all the data in their report which was necessary for the theoretical evaluation, but their study is subject to some question1" due to difference in prior history of various specimens and due to systematic differences in particle characteristics" which appeared to be associated with differences in the magnification of their microscopic examination. The current study was undertaken to obtain critical data in a manner which avoids some of these limitations. Specimens of eight Cu-Cr alloys remaining from a previous investigation&apos;&apos; were available in the form of 100 mil sheet of the compositions shown in Table I. At 200 mil this material had been previously an- nealed ½ hr at 1000°C, water quenched, and cold rolled 50 pct. Samples were further cold rolled to a thickness of 20 mil for a total reduction of 90 pct. Sheet tensile specimens of standard geometry with a gage length 2½ in. long and 0.20 in. wide were machined from this sheet. These specimens were then annealed in a dried N2-H2 atmosphere for the times and temperatures indicated in Table I. This anneal served two purposes: 1—to obtain a fairly uniform and nearly constant grain size of 0.015 to 0.022 mm average diameter, and 2—to precipitate a fairly uniform, nearly spherical over-aged dispersion of essentially pure chromium. A typical microstructure illustrating the grain size and the uniformity of the dispersion is shown in Fig. 1. A typical dispersion illustrating the range of sizes and shapes of the particles is shown in Fig. 2. The tensile specimens were tested in the Instron equipment described in ref. 11 at room temperature at a strain rate of 0.04 in. per in. per min. Three tests were run on each alloy with sufficient repro-ducibility that a single true stress-true plastic strain curve could be drawn through the three sets of data for each alloy. Typical curves are shown in Fig. 3.

Jan 1, 1956

By R. M. Goldhoff, J. W. Spretnak

IN connection with establishing the mechanism by which boron enhances the hardenability of heat treatable steels, this research work has been undertaken. Spretnak and Speiser1,2 indicated the need for studying high temperature effects in boron steels and, chief among these, the possible nonhomogeneous distribution of boron in iron grains. The occurrence of this effect may be of significance in explaining the mechanism of enhancement of hardenability by boron as well as in explaining some of the observed characteristics of boron steel behavior. Primarily, then, this work was undertaken a) to establish whether or not boron is adsorbed in ? solid solutions, b) to determine the nature of any such adsorption effects, i.e., whether it is positive or negative as well as its temperature coefficient, and c) to establish the magnitude of any such effect. While past literature on this specific subject is rather sparse, a number of authors have postulated that the observed temporary loss of hardenability as well as the occurrence of the characteristic boron constituent in these steels is due to the nonuniform distribution of boron in austenite.3-0 Experimental Techniques Attempts to obtain direct evidence of grain boundary effects in boron steels have been unsuccessful, both by using the technique of Chalmers&apos; in which small concentrations of solute made radioactive by irradiation are detected by autoradiographic means, and by means of studying cleavage fractures with the electron microscope.8 The present study attempts the design of experiments to measure the effect of boron on properties which might be subject to variation because of grain boundary effects. A study of the theoretical aspects of grain growth indicates that such studies may be pertinent. Another valid type of experiment involves the measurement in polycrystalline materials of properties whose values depend on the bulk of the grain, being negligibly influenced by grain boundaries. One such property is the lattice parameter measured by X-ray diffraction. The value of the lattice parameter reflects the average conditions which obtain over a relatively large number of atoms in a fixed crystalline lattice, and is therefore mainly dependent on bulk grain material. Measurement of lattice parameter variation over the austenite range of temperature in iron with and without boron should give evidence of concentration variations in the bulk grain material if adsorption effects are significant. Finally, use is made of the Grange and Garvey3 metallographic test for boron in which a characteristic boron constituent can be developed in austenite grain boundaries. The very occurrence of this phenomenon suggests grain boundary enrichment of boron and a study of the occurrence of this constituent and its varation with austenitizing temperature should help to detect grain boundary effects. Materials One lb ingots of pure iron, an Fe-B alloy, an Fe-C alloy, and an Fe-C-B alloy were prepared. The melting technique included an initial melting of electrolytic iron under vacuum followed by remelting under hydrogen and, finally, by melting under argon with the addition of alloying elements. Each ingot was surface machined between meltings. A quantitative spectrographic analysis was obtained on the pure ingot and, in addition, oxygen, nitrogen, and carbon were determined by the vacuum fusion method. The results of these analyses are given in Table I. Semiquantitative spectrographic analyses were performed on the alloy ingots, while quantitative determinations of the alloy additions were obtained. These analyses are shown in Table 11. The cast ingots were subjected to the following sequence of fabrication treatments: forging to 5/8 in. bars, swaging to 0.300 in. rounds, drawing to 0.025 and 0.010 in. wire. Portions of each ingot were retained in the swaged condition for experimental use. For certain portions of the work typical commercial steels were used. These materials were supplied by the Republic Steel Corp., Canton, Ohio, and correspond to AISI 8640 and AISI 86B40 compositions.

Jan 1, 1958

By Voyle R. McFarland, Robert A. Burmeister, David A. Stevenson

The distribution of lead between phases in the Ag-Sb-Te system was studied using microautoradio -graphy. Two compositions were investigated, both containing an intermediate phase Known as silver antimony telluride as the major phase, and one containing AgzTe and the other SbzTes as the minor phase. For both compositions, two thermal treatments were used: nonequilibrium solidification from the melt and long equilibration anneals of the as-solidified structure. For each composition, lead was segregated in the minor phase of the as-solidified structure, but was distributed in the matrix after anneal. The electrical resistivity and carrier type were insensitive to the distribution of lead in the two-phase structure. ThERE has been considerable interest in the Ag-Sb-Te system because of its thermoelectric properties. The major interest has been in compositions on the vertical section between AgzTe and SbzTes, particularly the 50 mole pct SbzTes composition AgSbTez (compositions are conveniently expressed as mole percent SbzTes along the AgzTe-SbzTes section). One of the major problems in the proper evaluation and utilization of this material is the inability to control the electrical properties through impurity additions: all alloys prepared to date have been p-type, even with the addition of large amounts of impurities. It has been shown Wit all the compositions previously studied contain an intermediate phase of the NaCl st&apos;ructure as a major phase (denoted by b) and a second phase, either AgzTe or SbzTe3, as a minor phase.&apos;-3 One explanation for the unusual electrical behavior of this material is that the impurity additions have a higher solubility in the second phase than in the matrix; the impurity would segregate to the second phase, leaving the bulk matrix essentially free of impurity.4 In order to investigate this mechanism with a specific impurity element, the distribution of lead between the two phases was determined using autoradiography. Lead 210 was chosen because of the suitability of its 0.029 mev 0 particle for autoradiography and also because of the interest in lead as an impurity in this system.5&apos;6 EXPERIMENTAL PROCEDURE Two compositions were taken from the vertical section between AgzTe and SbzTes, 50 mole pet SbzTes (Viz. AgSbTez) and 75 mole pct SbzTes, in which AgzTe and SbzTes appear, respectively, as the minor phase. Lead containing radioactive lead (pb210) was added to the above compositions to provide a concentration of 0.1 wt pct Pb. The material was placed in a graphite crucible in a quartz tube which was then evacuated and sealed. The samples were melted and solidified by cooling at a rate of 8°C per min and then removed and prepared for microa~toradiography. After autoradiographic examination of these samples, they were again encapsulated and annealed in an isothermal bath at 300°C for a number of days and prepared for examination. An alternate method of preparation employed a zone-melting furnace; the molten zone traversed the sample at a rate of 1.2 cm per hr and the solid was maintained at a temperature of 500°C both before and after solidification. This treatment had the same effect as solidification at a slow rate followed by an anneal for several hours at 500°C. In order to obtain the best resolution, thin sections of the alloy were prepared by hand lapping to a thickness of approximately 20 p. Other samples were prepared for examination by lapping a flat surface on the bulk sample. The resolution, although somewhat better in the former procedure, was adequate in both instances and the majority of the samples were treated in the latter fashion. A piece of autoradiographic film (Kodak Experimental SP 764 Autoradiographic Permeable Base Safety Stripping Film) was stripped from its backing, care being taken to avoid fogging due to static-electrical discharge. A small amount of water was placed on the sample, the film applied emulsion side down on the surface of the sample, and the sample and the film dipped into water in order to assure smooth contact. After drying, the film was exposed for 2 to 5 days, the period of time selected to give the best resolution. The film was developed on the specimen and fixed and washed in place. Two major factors must be considered in establishing the reliability of an autoradiograph: the in-

Jan 1, 1964

By W. A. Backofen, G. Y. Chin, W. F. Hosford

The ductile fracturing process was studied in single-crystal and poly cvystalline aluminum deformed in tension over a temperature range from 295° to 4.2°K. At temperatures as low as 77°K, the fracture of "inclusion-free" material, including zone-refined aluminum, was by rupture (-100 pct RA). At 4.2 OK, fracture was brought on by adia-batic shear. Metallographic examination did not disclose any voids or slip-band microcracks, thus negating for inherently ductile metals any mechanism of void nucleation by vacancy condensation or of cracking due to dislocation pile-ups. In Izigh-purity aluminum not treated to be inclusion-free, fracture at temperatures as low as 45°K was of the double-cup type and a result of void formation. The reduction-of-area decreased as temperature was lowered, corresponding to the earlier appearance of voids. Such behavior was rationalized in terms of a larger increase, with decreasing temperature, in the .flow stress relative to the strength of the inclusion-matrix interface. Evidence for low-temperature adiabatic shear was found in discontinuous flow at 4.2"K, in the transition to a localized shear fracture at low temperatures, and in the suppression of shear fracture with an elastically hard pulling device. A simple analysis for the initiation of adiabatic shew permitted a general correlation of the various contributing factors. It has been pointed out that the duration of shear depends upon effective mass and elastic stiffness of the deformation system. IT has long been recognized that fracture* may Throughout this paper, the term "fracture" is taken to mean any process that results in the separation of a material into two (or more) parts. Thus rupture as it may be encountered in a tension test leading to 100 pct reduction-of-area is included in this category. occur in a ductile mode, and that the process can be of great practical as well as general interest. Much information about ductile fracture has also been accumulated over this period, but only recently has an understanding of mechanism begun to appear. Ludwik,&apos; in 1926, first reported fracture in a tensile specimen starting with a central crack in the necked section. Since then, other studies have disclosed that such cracks may form by the coalescence of voids nucleated in this region where hydrostatic tension is highest.2-4 Rogers and Crussard et al.&apos; have emphasized void formation and reori-entation along localized shear bands as a mode of crack propagation. pines6 has considered the tensile rod as a bundle of fibers joined by weak interfaces, which subsequently separate to allow individual fiber contraction. The notion of cavity growth and coalescence by purely plastic processes was discussed by Cottrell: who added that the tensile reduction-of-area ought not to be sensitive to temperature. On the other hand, it has been observed that the reduction-of-area is greatly increased if tests are carried out at high temperaturesa or under high hydrostatic pressure.&apos; Fracturing anisotropy in wrought products lends support to the idea of void formation from preexisting flaws strongly aligned by earlier processing.&apos;&apos;-l2 There is evidence that many voids result from the fracturing of inclusions or separation at the inclusion-matrix interface Another possibility is that voids grow out of pore volume produced in the initial solidification and never fully removed in later working. In general, a structure 3f particles, pores, and weak interfaces can be expected, at least in materials of engineering interest. Vacancy condensation has been suggested as an alternative mechanism of void formation for materials considered to be inclusion-free.13 Yet experience has shown that tensile reduction-of-area increases with purity, to the extreme of rupture as so often observed in single crystals. Adiabatic shear has an important bearing on ductile fracture. It occurs when the decrease of flow stress, as a result of local temperature rise from heat generated during straining, becomes larger than the increase due to strain and strain-rate hardening. As demonstrated by experiments on punching of plates,14 a large temperature rise may be brought about by rapid straining. Adiabatic flow as a result of the high strain rate reached in an ordinary tensile specimen just prior to separation may account for the cone formation in cup-and-cone fracture;14 evidence of such local heating has been presented.15 For geometrical reasons, however, pure sliding along the conical surfaces is unlikely, and separation under tensile forces is probably an important accompanying feature of the shear.7 In deformation processing operations, a high shear-strain rate may exist at boundaries between plas-

Jan 1, 1964

By R. L. Fleischer, W. F. Hosford

Tensile data for coarse grained aluminum Polycrystals suggest that the "grain size" effect is not due to dislocations piled up at grain boundaries but rather is primarily a relative size effect due to surface crystals being weaker and less confined. STUDIES directed at interpreting hardening of poly-crystalline metals normally identify their strain hardening properties with those in some particular type of single crystal.1"4 The recent recognition in face centered-cubic metals of a nearly linear stage with rapid hardening occuring at comparable rates for both polycrystals and single crystals, suggested that the same process or processes determine both cases and hence that there exists some justification for the use of single crystals to understand polycrystals. Further evidence for the above view may be found by an approach initiated by Chalmers:5 By using bicrystals of controlled orientation it is possible to begin to assemble a polycrystal and also to study grain boundary effects in detail. In this way it has been found that a single grain boundary affects easy glide but not the subsequent stage II hardening.6 This result suggests that a sensitive way to observe grain boundary effects in polycrystals would be to vary grain size and measure easy glide. As will be seen, easy glide is only possible for coarse-grained samples, and hence the results will serve to fill in the gap in measurements between single crystals and bicrystals on one hand and fine-grained polycrystals on the other. One problem inherent in comparing single crystals with polycrystals is the uncertainty as to what slip systems are acting in a polycrystal. To compare the two types of samples, rates of shear hardeninn---L. on the acting -planes are needed. and these may be computed only if it is known what particular systems are active. The acting systems were examined for a coarse-grained polycrystal and it will be shown that the systems supplying the preponderance of slip can be determined with little ambiguity. EXPERIMENTAL PROCEDURE Twelve samples of aluminum were prepared by chill casting into a heated graphite mold, followed by annealing at 635° ± 5°C for 24 hr with an 8-hr fur- nace cool, and finally either etching7 or electropol-ishing.&apos; The samples, with a 7 to 10 cm length between grips and 4.4 by 6.6 mm in cross section, were deformed at a strain rate of about 3 10 -3 . per min in a tensile device which has been described elsewhere.5 The composition was reported by Alcoa as 99.992 pct Al, 0.004 pct Zn, 0.002 pct Cu, 0.001 pct Fe, and 0.001 pct Si; nine samples were deformed while immersed in liquid helium and three in air at room temperature. The stress-strain curve for one of the samples (P-1) deformed at 4.2 "K has been reported previ~usl~.~ This sample was selected for determination of active slip systems. Eighteen of the crystals were examined by optical microscopy to determine the angles of slip line traces and by X-ray back reflection to determine orientation. By this means the slip planes were determined and the resolved shear stress factors for possible slip systems could be computed. Finally each sample was sectioned so that after etching, the number of crystals could be counted for each of ten newly exposed surfaces. The average of these ten values will be termed n, the number of crystals per cross section. Values of 11, varied from 1.9 (nearly bamboo structure) to 12.7. Sketches of typical cross sections appear in Fig. 1. RESULTS AND DISCUSSION: SLIP SYSTEMS 1) Determination of Acting Slip Planes—The stress axis orientation and operative slip planes in eighteen crystals of sample P-1, as determined by slip line traces and crystal orientation, are summarized in Fig. 2. For one of the crystals two planes had a common trace. so that the traces alone did not distinguish which plane or planes were slipping. However it was found that the stress resolving factor for the primary system was 0.386, .while that for the most stressed system in the other plane (indicated bv the dotted arrow) is 0.138. It will be assumed tgerefore that only the primary plane acted. Since the orientations were determined after extending the samples 4 pct, the stress axes may be rotated from their original value by as much as 2 deg in some cases. It is interesting to note that in five crystals only one slip plane acted, in eight two acted, and in five three planes were observed—an average of two slip

Jan 1, 1962

By M. J. Marcinkowski, A. Szirmae, R. M. Fisher

Room -temperature hardness measurements obtained from single and polycrystalline samples of a 47.8 at, pet Cr-Fe alloy which were aged for various times al 500°C show a two-fold increase over that of the unaged alloy after annealing for 1000 hr. A detailed examination of the deformation markings in the neighborhood of the hardness imbressions reveals that twinning becomes an increasingly more important mode of deformation as aging proceeds. this observation is shown to be inconsistent with the Proposals that the transformation is eve of order-disorder On the other hand, the results are in agreement with previous observations of Fisher et al. of a coherent chromium-rich precipitate which forms in an iron-rich matrix as a result of a miscibility gap in this alloy system as proposed by Williams . Using the coherent precipitate hypotlzesis as a model, a detailed analysis of the various possible strengthening contributions to both the slip mid twinning stresses is made. In the case of&apos; slip, lattice friction within the chromium-rich phase and the chemical energy associated with the interface between the two phases contribute about 60pet to the total strength. The contributions from coherency strains and modulus differences are thought to contribute the remaining 40 pet of the strength but are difficult to evaluate because of uncertainties regarding the flexibility of the dislocation line. All of the factors have nearly the same or else a smaller effect on the twinning stress in the aged alloy. Twinning is never observed in the unaged alloy because the twinning stress is much higher- than that for slip. With increased aging times, the various contributions to the total stress for both twinning and slip increase, but most of those for slip increase much more rapidly, so that, in the fully aged alloy, it surpasses the stress for twin propagation. When a twin is nucleated by the chance occurrence of an internal stress concentration during a test, the subsequent twin burst results in a low hardness reading. FeRNTIC Fe-Cr alloys from about 15 to 80 at. pet Cr content show considerable change in properties such as hardness, electrical resistivity, saturation magnetization, and so forth, after aging in the vicinity of 500°C.* The most marked change is a large increase in hardness accompanied by a sharp decrease in ductility, so the phenomenon has often been referred to as the 475°C (885°F) em-brittlement problem. Changes in microstructure are rather subtle and most investigators have not been able to observe any X-ray diffraction or metal-lographic changes during aging. There is little doubt that the phenomenon is inherent to the Fe-Cr binary system and is not directly related to the formation of a phase. Two distinct schools of thought have developed during the past decade concerning this problem. Masumoto, Saito, and sugiharal have concluded, from their own specific-heat measurements, that atomic ordering occurs in this temperature range. Pomey and Bastien2 have also attributed the changes in physical properties with aging in the neighborhood of 500°C to atomic ordering. In addition, Takeda and Nagai3 claimed to have found X-ray verification for superlattices corresponding to the compositions FesCr, FeCr, and FeCr3. However, all known attempts to observe superlattices in Fe-Cr alloys using neutron diffraction, which should be much more sensitive, have been unsuccessful. These have been reported by Shull et al.4 for 25 at. pet Cr, williams5 for 75 at. pet Cr, and Tisinai and samans6 for a 28.5 at. pet Cr. steel. The second and more prevalent opinion ascribes the 475°C embrittlement phenomenon to the formation of a coherent precipitate due to the occurrence of a miscibility gap in the Fe-Cr system below about 550°C. This latter concept was first indicated by the results of Fisher, Dulis, and Carroll,7 who were able to extract fine particles about 200Å in diameter from samples of 28.5 at. pet Cr steels aged from 1 to 3 years at 475°C. The extracted material was found to be nonmagnetic, to have a bee structure with a lattice parameter between that of iron and chromium, and to contain about 80 at. pet Cr. Williams and paxton8 and williams5 confirmed these results and first explicitly proposed the existence of a miscibility gap below the a region in the equilibrium diagram. Alloys aged within this gap

Jan 1, 1964