Search Documents

By M. E. Nicholson

The effect of boron on the austenitic transformation rate of iron is smaller than on low carbon steels. The influence of austenitizing temperature on B-Fe is the reverse of its influence on steels. THERE have been many studies made of the influence of boron on the hardenability of steel, but apparently none has been made of its influence on the y-a transformation of pure iron. There are several facts suggesting that boron should have a pronounced effect on the transformation rate of iron. First, Simcoe et a1.l indicated that boron reduces the nucleation rate of ferrite and bainite. Second, they showed, along with others,', " that the lower the carbon content of steel the greater the influence of boron on hardenability. If this trend extends to pure iron, the influence on rate of ferrite formation should be considerably greater for iron than for medium carbon steels. According to Rahrer and Armstrong," the multiplying factor for boron in pure iron should be about 2.40, compared with 1.50 in a 0.35 pet C steel. According to an extrapolation made by Grange and Mitchell,' the effect should be even greater, and the multiplying factor should be about 3.5 in iron. Many investigations of the boron influence'.7, 2, 5 indicated that boron is effective only when in solid solution. On the other hand, Chandler and Bredig" suggested that boron increases hardenability by combining with nitrogen, thereby preventing formation of AlN, which catalyzes the decomposition of austenite. If their hypothesis is valid, boron should have no effect on an alloy free from nitrogen. Digges et al." showed that so far as low nitrogen high purity Fe-C alloys are concerned this is not the case. No experiments, however, have been made on low nitrogen iron. To determine whether or not boron has an effect on low nitrogen iron and, if an effect exists, to determine whether it is as large as predicted from the investigations of boron treated steels, the following work was performed. Because of the rapidity with which iron transforms from austenite to ferrite at even a moderate degree of supercooling, it was decided to study the influence of boron on the transformation rate of iron by determining the effect of quenching rate on the temperature of the beginning of transformation. The technique, essentially that used by Greninger' and Duwez,H consisted of heating small specimens, 0.1 in. sq and 0.010 in. thick, in an atmosphere of purified helium with a resistance heater coil, and then quenching the sample in a jet of helium gas. At the time the jet was applied, the heating coil was removed from around the sample. The sample was suspended in the furnace on 30 gage chrome1 and alumel wires, one welded to each side of the specimen, which also served as a thermocouple for measuring the specimen temperature. Specimens were prepared from vacuum-melted iron obtained from the National Research Corp. which was rolled to a thickness of 0.060 in. and then decarburized in wet hydrogen for 51/2 hr at 700°C. This treatment also removed any boron present in the iron. The resulting iron contained 0.001 pet C. 0.0002 pet N, and 0.005 pet 0. One half of the piece was then boronized by surrounding it with 325 mesh boron powder and heating it for about 2 hr at 900°C in H,. The boronized iron was then homogenized at 1100°C for 24 hr. The iron boride case formed by boronizing was removed by grinding 0.010 in. from each side of the plate, and the piece was finally rolled to a thickness of 0.010 in. The resulting alloy contained

Jan 1, 1957

By D. J. DeLazaro, W. Rostoker, R. E. Riley, M. Hansen

At very low concentrations, carbon dissolves interstitially in molybdenum resulting in a linear expansion of lattice parameter with increase of carbon in solid solution. Geometrical consideration of the relative size of carbon atom to size of interstice approximately predicts the observed volume expansion. THE element carbon, occurring in molybdenum, either as an unavoidable impurity, or purposely added, markedly affects the mechanical properties of molybdenum. Several investigators1-" have noted the occurrence of molybdenum carbide at the grain boundaries of cast molybdenum, and Fischer and Rengstorff' have shown that this intergranular constituent can induce intergranular brittleness. The appreciable change, with temperature, of the solid solubility of carbon in molybdenum, found by Few and Manning," suggests other important effects upon mechanical properties. Finally the relative atom diameters of carbon and molybdenum (the ratio of atom diameters is 0.59) are indicative, by analogy with iron (ratio of carbon atom diameter to iron atom diameter is 0.65), of a possible interstitial solid solution. If carbon dissolves intersti-tially in molybdenum, anelastic effects and age-hardening effects, similar to those observed in other body-centered cubic metals, could be expected. However, from the work of Sykes, Van Horn, and Tucker," it might be inferred that carbon forms only a substitutional solid solution with molybdenum. These considerations made it desirable to study the effect of carbon on the lattice parameter of molybdenum in greater detail than heretofore. All heat treating was done in a high temperature furnace7 built specifically for heat treatment of molybdenum. The temperatures and times of heat treatment were determined from the a solubility limit for the Mo-C system." These heat treatments were carried out in argon which was purified with respect to N, and H.!0." Purification of the argon was accomplished by passing the argon over hot (750°C) titanium and then through a magnesium perchlorate drying tower. As many as six samples were run concurrently and quenched at different times without interrupting the furnace cycle. Both the purity of the furnace atmosphere and ability to quench samples from any temperature up to 4000 °F were of prime importance in the successful heat treatment of samples for the lattice parameter investigation. Carbon Analysis The Leco Combustion apparatus was used for carbon analysis. This apparatus is capable of an accuracy of & 0.003 pct for a 1 g sample in the range below 0.10 pct. However, it is felt the degree of accuracy is somewhat better than this limit in view of the consistency evident by cross checking a number of determinations. The Battelle Analytical Laboratory consistently reported check results to within k 0.001 pct C. X-ray Measurements The molybdenum wire specimens (20 mils) were carefully filed down to about 12 mils and then etched with nitric acid to 8 mils. Carbon analyses were made on specimens before reduction in size; however, since there was no evidence of surface carburization, it is probable that the carbon was uniformly distributed throughout the sample. The resultant specimens were strain free and small enough to minimize the error in the lattice parameter determinations due to X-ray absorption. Diffraction patterns were obtained with a Debye-Scherrer powder camera 114.59 mm in diam utilizing the Straumanis type asymmetrical film mounting. Nickel-filtered copper. Ka radiation and zirconium-filtered molybdenum Ka radiation were used. Line positions on the film were measured with a traveling microscope equipped with a vernier scale permitting measurement to 0.001 cm. The average of five readings was used to determine the position of each line. The lattice parameter for each specimen was determined from the data by the extrapolation method of Bradley and Jay, Y.e., the intercept at 90" of the straight line obtained by plotting the apparent lat-

Jan 1, 1953

By J. W. Freeman, E. E. Reynolds, A. E. White

Fram a study of 63 systematic alloy modifications it was found that molybdenum, tungsten, and columbium, added individually or simultaneously, and increases in chromium cause major improvements in 1200°F rupture strengths of Cr-Ni-Co-Fe base alloys. Rupture strengths were a function of the effect of composition modifications on both the inherent creep resistance and the amount of deformation the alloy would tolerate before fracture. THIS paper describes the results of an investigation of a series of alloys with systematic variations of the chemical composition of the following basic alloy: C, 0.15: Mn, 1.7; Si, 0.5; Cr, 20.0; NI, 20.0: Co, 20.0: Mo, 3.0; W, 2.0; Cb, 1.0; N, 0.12; Fe, 32.0 pct. The 62 modifications of this alloy were produced under conditions which minimized all factors influencing properties at high temperatures except composition. Melting, fabrication, and heat treatment were carefully maintained constant. Stress-rupture properties at 1200°F were used as the primary criteria of evaluation of the alloy. The objective of the study was to obtain data for determining the fundamental role of the influence of alloying elements on properties of heat-resistant alloys at high temperatures. In addition the results should be useful in determining optimum chemical compositions, the sensitivity of properties to variations in composition, and the degree to which alloy content could be reduced while retaining worthwhile properties. It is difficult or impossible to develop correlations between properties at high temperatures and systematic variations in chemical composition from published data for wrought heat-resistant alloys developed for gas turbines.' ' The main reason for this is the extreme dependence of the properties on conditions of treatment of the alloys." In most cases variation in final treatments between alloys so influences the properties that the influence of chemical composition is obscured. In addition it is recognized Table I. Basic Alloy and Some Modifications Used Basic AllOy, Variations in Element Pct Composition, Pct C 0.15 0.08. 0.40. 0.60 Mn 1.1 0.03,0.25.0.50,1.0,2.5 S1 0.50 1.2, 1.6 Cr 20.0 10, 30 Ni 20.0 0, 10,30 Co 20.0 0. 10, 30 MO 3.0 0. 1.2.3, 5, 7 W 2.0 0, 1, 5, 1 Cb 1.0 0.2,4,6 N 0.12 0.004, 0.08, 0.18 Fe 32.0 that variations exist between heats of the same alloy which are related to melting practice and that there is a strong possibility that conditions of hot working influence response to final treatments. The development of heat-resistant alloys has been based on the gradual accumulation of data roughly related to composition from extensive testing programs. There is every reason to believe that in most cases the optimum compositions have been achieved by this procedure in the alloys commercially available. There are, however, very little data showing the influence of systematic variations of composition free from the influence of other factors, particularly for alloys of the type investigated. Several investigators of cast alloys have demonstrated compositional effects, notably Grant,1-6 Epremian,t Guy,8 and Harder and Gow.9 Sykes10 eviewed the work on the wrought alloy Rex 78 and the systematic variations of carbon, copper, molybdenum, and cobalt leading to the development of the stronger Rex 337A alloy. From the papers by Wilson11 and Henry12 it is possible to deduce the beneficial effect of substituting cobalt for iron in 0.45 pct C-20 pct Cr-20 pct Ni-4 pct Mo-4 pct W- 4 pct Cb alloys. Wilson mentioned but did not present the extensive compositional studies involved in developing these alloys. Binder" showed optimum properties for 3, 2, and I pct, respectively, for molybdenum, tungsten, and columbium in 20 pct Cr-20 pct Ni-20 pct Co-30 pct Fe alloys for limited systematic variations of these

Jan 1, 1953

By D. H. Thompson, A. W. Tracy

Season-cracking is a type of failure of brass that results from the simultaneous effect of stress and certain corrodants. The object of this paper is to present data that will aid in a more complete understanding of the mechanism of season-cracking and related phenomena. Results presented show that certain high copper alloys are susceptible to season-cracking or stress-corrosion cracking, and possible explanations are discussed. Starting at least as far back as 1906, many papers have been devoted to this subject but the symposium1 held in Philadelphia in 1944 is the richest source of information. In order to study season-cracking, several of the many variables were held constant so as to learn the effects of others. Season-cracking is generally understood to refer to the corrosion cracking of brass having internal stresses;²,³ it is a special case of the general stress-corrosion cracking. Inasmuch as applied stresses are more readily produced and controlled, they were used exclusively in this research and the resulting phenomenon must he called stress-corrosion cracking.²,³ Only constant tensile stresses were used. The agents believed to be most frequently responsible for season-cracking are ammonia. amines and compounds containing then]. Both moisture and oxygen also appear to he necessary. Therefore, an atmosphere containing ammonia, water-vapor and air was selected for these tests. Briefly, the work consisted of exposing sheet metal specimens, having a reduced section ¼ by 0.050 in., of copper-base alloys to the effect of static tensile stresses between 5,000 and 20,000 psi and simultaneous contact with a. continuously renewed atmosphere containing 80 pct air, 16 pct ammonia and 4 pct water vapor at 35°C. The gas mixture and the speci- mens were maintained above the dew-point. The time-to-failure in minutes was the primary measure of results. In order to limit the experiment to finite time, it was considered that a specimen which had neither failed nor undergone microscopically detectable cracking in 40,000 min. (4 weeks) while under a stress of 10,000 psi or more could be considered immune to cracking. This is merely a convenient limit and is not to be considered proof of immunity. Supplementary tests in the absence of stress using weight loss or microscopical appearance as measures of attack were made. Apparatus The apparatus used in this research is shown in Fig 1. To facilitate the description it may conveniently be divided into six parts: stress-producing units, test chamber, gas train, electrical controls, timers and gas analysis device. A stress-producing unit is shown in an exploded view at the left in Fig 2. At the right is an assembled unit with a specimen in place in the lower portion; it is this part that remains in the ammonia atmosphere during a test. The upper part contains a spring, a central threaded rod, a large nut and necessary washers, pins, and so forth. Stress is produced in the specimen by screwing down the top nut against the spring, thus putting a tensile load on the central rod and so on the specimen. The wrench that turns the nut by extending through the upper cap, is seen at the upper right of the figure. The magnitude of the load is gauged by measuring from the pin that extends through the side of the tube, to a fixed point on the large flange. Measurement is made with a vernier beam caliper, shown at the right of the figure. The necessary spring compression to give a desired stress is calculated from the calibration curve of the spring and the dimensions of the specimen. The test chamber, center Fig 1, consists of a thermally insulated steel box 32 in. long by 10 in. high by 7 in. wide. A horizontal baffle reaching nearly to each end divides the chamber equally. Below this baffle are inlets for air and ammonia, a heating coil and a fan. Thus the gases are warmed and mixed in the lower level and flow past the specimens in the upper level. A thermo-regulator and thermometer project into the upper space. The top is pierced by 12 ports flanked by 3/8 in. threaded studs. A test starts when a port is opened and a unit containing a stressed specimen is thrust through it and bolted down against a neoprene gasket. The test chamber is held at 35°C. The gas train, right rear Fig 1, carries ammonia and air continuously to the test chamber. Tank ammonia passes through two reducing valves, a needle valve, a flow meter and into the test chamber. The air from either the plant compressor or a small laboratory compressor passes through wool towers and flow controls to the flow-meter. It then bubbles through water at 34°C and through a heated line to the test chamber. Electrical controls, left rear, Fig 1, provide rectifiers and mercury relays for the test-chamber and humidifier-heating-control circuits and outlets for

Jan 1, 1950

By D. H. Thompson, A. W. Tracy

E. A. ANDERSON*—At the outset, I note that you are using a humid atmosphere containing ammonia but that you make no reference to the variable of carbon dioxide content. Edmunds in his work in this laboratory found very marked effects on the rate of failure due to variations in carbon dioxide in the environment. This point is, of course, strongly related to the overall corrosion rate problem since the role of the carbon dioxide seems to be to permit the formation of hygrogroscopic salts which give a controlled moisture film on the specimen surface, which in turn seems to support the intergranular penetration more consistently than would otherwise occur. (2) Your results with various copper binary systems are very striking. It is curious, however, that the time-to-failure minima all occur at percentages of the alloying element which are considerably below the solubility limits as given in the conventional equilibrium diagrams. If your theory regarding the presence of these impurities in some concentration in the grain boundaries is correct, then either the existing diagrams are not accurate in the room temperature region, or there is a difference in solubility in the grain boundaries as compared -with the grains. A study along these lines might be very revealing. (3) The undesirable effect of silicon in copper calls to mind our own observations on the influence of silicon on the stress corrosion cracking resistance of alpha brass. In this case, silicon was found to have a very marked beneficial effect, particularly when a heat treatment capable of producing a grain boundary constituent was used. I should appreciate it if in the discussion of your paper this point should arise, you would attempt to clarify the difference between the copper-silicon binaries and the copper-zinc-sili-con ternary alloys. D. H. THOMPSON and A. W. TRACY (authors' reply)—(1) We have no data on the constancy of the carbon dioxide content of the air used for the test atmosphere but have believed that the normal carbon dioxide content of the air was as constant as could be obtained by using Edmunds' method of removing carbon dioxide from the air and then adding a measured quantity. In any event, the test atmosphere was the same for all specimens in a test run. We agree with Mr. Anderson that the carbon dioxide content is important in the formation of a hygroscopic film on specimens. (2) We can imagine that there could be a concentration of solute atoms at the grain boundaries which would be so small that present methods would not detect it even if it exceeded the solubility limit of the alloy. There could be somewhat greater solubility at the grain boundaries for an interstitial solute. There is a possibility that phosphorus dissolves in this way but we believe that none of the other solutes studied does. In our present studies we hope to find out something about conditions at the grain boundaries of some of the systems mentioned in the paper. (3) Mr. Anderson points out that silicon brass, which has had a high temperature heat treatment followed by a quench. is highly resistant to stress-corrosion cracking. Although the test conditions used by Anderson* et al were different from our test conditions, it is noted that the silicon brasses which had not had the special heat treatment were less resistant to stress-corrosion cracking than copper containing approximately equal amounts of silicon. G. R. GOHN†—Nonferrous metallurgists and particularly, materials engineers, have been accustomed to thinking

Jan 1, 1950

By R. H. Frazier, C. H. Lorig, F. W. Boulger

This investigation establishes the effect of ferrite grain size resulting from various heat treatments on the transition temperature of a semikilled steel plate. Different austenitizing temperatures and various cooling rates were used. The ductile-brittle transition temperatures were determined by the Navy tear test and the keyhole Charpy test. THE data presented in this paper deal with quality characteristics of ship-plate material which were investigated in a research project sponsored at Battelle by the Bureau of Ships, Dept. of the Navy. Specifically, the object of this investigation was to establish the effect of ferritic grain size (resulting from various heat treatments) on the so-called transition temperature of ship-plate steel. Transition temperature is not a fixed property of steel. It is derived from a series of static or dynamic tests made at various temperatures and is qualified by specifying the type of test employed as well as the testing criteria. Because in earlier investigations of ship-plate quality1,2 the so-called Navy tear test and standard notched-bar tests (keyhole Charpy) proved to be useful in interpreting instances of brittle behavior of ship plate in service, these tests were used in the investigation reported in this paper. By definition,' in the Navy tear tests the highest temperature at which one or more of four specimens breaks with a brittle fracture (that is, when less than 50 pct of the fracture area has a dull fibrous texture) is termed "transition" temperature. In the Charpy tests, the 12 ft-lb level of energy absorption was used as a criterion indicating the "transition" temperature, although other levels of energy absorption were also used for comparison. Earlier work" on ship-plate steels indicated that the temperature at which ship plate is finished has a very significant effect on its notched-bar properties. Plates rolled in the laboratory, where the finishing temperature can be carefully controlled, showed a 16°F decrease in tear test transition temperature when the finishing temperature was lowered 200°F (from X" to Y°F). The same plates showed a drop of 10°F in the keyhole Charpy transition temperature from the same decrease in finishing temperature. Commercially finished plates' exhibit a similar trend. When the ferrite grain size of the hot-rolled laboratory plates was determined, a close relationship was found between the ferrite grain size and the notched-bar transition temperature." " he indicated relationship between grain size and transition temperature was in agreement with the findings on low carbon steels of Hodge, Manning, and Reichhold' despite the differences in composition of the steels. The cooling rate after rolling varies from one steel plant to another. This variation changes the micro-structure" and appears very likely to affect the notched-bar properties of the steel plates. In the investigation summarized in the present paper, heat treatments simulating finishing practices in the hot rolling of ship plate were used in order to vary the ferritic grain size. It is believed that the indicated relationship between grain size and transition temperatures of the ship-plate material will prove useful in estimating the effect of rolling temperature and of cooling rates from rolling temperatures on the notched-bar properties of semikilled steel plate. Material The semikilled steel plate used in this investigation was a ¾ in. hot-rolled plate from an open hearth heat. Other plates from this heat have been used on many other studies performed for the Ship Structure Committee," "," and the heat has been identified as project steel "A". The chemical composition of the plate1 was 0.25 pct C, 0.49 pct Mn, 0.011 pct P, 0.045 pct S, 0.04 pct Si, and 0.004 pct N.

Jan 1, 1956

Using 5-p Ni powder and 0.018 ,u A1203, oxide dispersion strengthened nickel alloys were prepared by mechanical mixing of powders, followed by compaction, sintering and extrusion. Processing variables such as cooling of the powder during mixing, electrostatic discharging, mixing time, amount of oxide, and so forth, were studied to determine the effects on room-temperature tensile and high-temperature creep-rupture properties and on the reproducibility of alloys. MECHANICAL mixing of metal and metal oxide powders provides one of the simplest and most inexpensive methods for preparing dispersion strengthened metal-metal oxide alloys;" however, because of large differences in specific gravity, powder particle diameters and other variables, difficulties have been encountered in reproducing alloys and alloy properties. Using 5-p Ni powder and 0.018 p A1203, the following variables were investigated: a) Blending techniques b) Blending time c) Volume fraction of oxide for the selected pow- ders d) Sintering of compacts before extrusion Cooling of Powders During Blending— Cremens and Grant had indicated that dry ball milling of the powder mixture gave superior results over other procedures. When ultra-fine metal and oxide powders became available and comminution was unnecessary or offered little gain, the use of dry mixing in a Waring Blendor gave optimum results.' In the current study, observations of the powder mixtures indicated that considerable heat was generated due to the high speed of the Waring Blendor (15,000 rpm). This heating appeared to produce some degree of clustering and pelletizing. To minimize such agglomeration, a Pyrex cooling coil was installed in the mixing vessel. A double coil, water cooled, proved to be quite satisfactory, providing a fair degree of cooling along with good erosion resistance. Discharge of Electrostatic Charge—Electron-microscopy showed that agglomeration was minimized by the cooling procedure but was not entirely eliminated. It appeared that some of the ag- glomeration had to be explained on the basis of an electrostatic attraction due to the high-speed blending operation. These charges had the effect of promoting the growth of alumina clusters. At the end of the blending procedure such clusters had an effective size which was as much as 50 times that of the individual powder particles and were very tightly bunched. Several methods were utilized to try to discharge the electrostatic forces to minimize the clustering. One successful method, utilized in alloy 17, involved continuous exposure during blending to a radium source of 50 millicuries at a distance of 1.5 ft from the container. A number of other methods were noted to work equally well. Fig. 1 shows the more open oxide structure which results from such a treatment, permitting the matrix metal to penetrate into the cluster more effectively. The combination of powder cooling and discharging led to noticeably improved structures. Fig. 2 shows a cross and a longitudinal section in alloy M-17, one of the best alloys, illustrating the marked decrease

Jan 1, 1961

By R. H. Frazier, C. H. Lorig, F. W. Boulger

THERE are both advantages and disadvantages in using semikilled steels in place of killed steels. One advantage of semikilled steels is they provide a higher ingot-to-product yield. This is especially important to shipbuilders in the time of national emergency. By using semikilled steel for hull plates, a greater number of ships can be built from the same ingot tonnage. Consequently, if semikilled steel plates are adequate for the service, the advantage of the higher product yield is of considerable importance. The performance of hull plates is closely associated with the ductile-to-brittle transition temperature, and this, in turn, is strongly dependent on the composition of the steel. A low transition temperature is desirable because it indicates that the steel is less likely to fail at low ambient temperatures. Killed steels are known to have lower transition temperatures than semikilled steels. It is believed that the better qualities of killed steels in this respect are due mainly to the low oxygen contents of the steel. The principal deoxidizers, aluminum, silicon, and manganese, lower the oxygen content. Fundamental studies1-0 have shown that the oxygen content remaining after the addition of one of these three elements is influenced by the residual amounts of the other two present. In the current study, therefore, various amounts of silicon and aluminum were added to steels containing different manganese contents for the purpose of studying the influence of silicon and aluminum on the notched-bar properties of hot-rolled steels. Eleven types of steels were studied. The temperature at which the plates were finish-rolled was care- fully controlled at 1850°F. All plates were rolled to ¾-in. thickness, and tested in the as-rolled condition. The total number of steels prepared in the laboratory for this study was 95. The charge consisting of ingot iron and ferrosilicon equivalent to 0.10 pct Si was melted in a 200-lb induction furnace under an atmosphere of argon to insure low, uniform nitrogen contents. After the charge was melted and the desired temperature was obtained, the melt was partly deoxidized with either silicomanganese or aluminum. Aluminum was used for this purpose in only those steels with very low silicon contents, where the finished steel was to contain some aluminum. This initial deoxidizing addition was made to obtain consistent recoveries of subsequent additions of ferro-manganese, ferrosilicon, and aluminum. Carbon, in the form of graphite, was added, either just prior to tap or to the final aluminum addition. The entire heat of 200 lb was poured directly into a 6x6-in. big-end-up mold. The ingots of semikilled steel were capped with a steel plate. The killed steels, on the other hand, were poured with a hot-top containing 14 pct of the total volume of the ingot. The ingots were processed by heating to 2250°F, followed by forging to slabs 1¾ in. thick and 6 in. wide. After reheating to 2250°F, the slabs were rolled to 0.9-in. gage, using reductions of approximately 1/6 in. per pass. The 0.9-in. thick plates were immediately recharged in a furnace held at 1850°F. After 30 min in the furnace at 1850°F, the plates were rolled to ¾ in. in one pass. Following the final pass, the plates were stacked on edge on a brick floor, with a brick separating one from another, where they were allowed to cool in air. Drillings for chemical analysis were taken from the plates at locations corresponding to the top and bottom of each ingot. Carbon, manganese, silicon, phosphorus, sulfur, and nitrogen contents of each sample were determined. The analysis of each steel was carefully controlled so that the contents of

Jan 1, 1957

By F. Bonaccorso, G. Venturello, C. Antonione

A study of the effect of small amounts of interstitial impurities on recovery and re crystallization in high-purity iron (99.995 pct) has been undertaken. This paper gives results on the effect of carbon, introduced in small-dosed amounts @om 0.0005 to 0.0086 wt pct) by heating iron specimens of high purity m a static atmosphere of CO + ,. The materials prepared in this way, cold-worked 80 pct and subjected to a series of isochronal and isothermal annealings, were submitted to examinations by X-rays, micrographs, and hardness tests. It was observed that effect of carbon is remarkable in the sense of blocking recovery of mechanical properties up to the temperature at which re crystallization begins. On the contrary, carbon has a negligible effect on primary re crystallization temperature, when compared with the known effect of substitutional impurities. This is in agreement with the high mobility of interstitials. In effect, only a slight decrease, -20 pct, of the grain-boundary motion rate was noted, due to the interaction between the grain boundary and the carbon atoms. On the other hand, in the samples in which the carbon content is above the solubility limit at the temperature at which re crystallization occurs, a slight increase of nucleation frequency is noted due to the presence of precipitated carbides. ThE effect of purity on recovery and recrystalli-zation phenomena has been known for a long time; however, recently, new attention has been given to the problem since new methods for obtaining metals with extremely low impurity contents have become available. Most of this research work essentially concerns the effects of impurities which cause precipitates or give rise to substitutional solid solutions. The works of Bolling and winegard1 and Aust and utter' on lead, and Vandermeer and orddon' on aluminum, 01sen4 on nickel, and Abrahamson and Blakeney on iron should in particular be referred to. On the effect of this type of impurities a quantitative theory has been formulated by Detert and Lucke6 and has lately been discussed critically by Cahn7 and Gordon and vandermeer.' Interstitial solid solutions in iron have not as yet been studied. As the study of the effect of interstitials is of great interest both from a theoretical and practical standpoint, it was deemed useful to examine the effects of carbon, nitrogen, and boron on recovery and primary recrystallization of iron. There already is some work by Chaudron et al.,1-" on the effect of interstitials on iron; their work, however, mainly concerns secondary recrystallization. The present paper refers in particular to the effect of carbon. EXPERIMENTAL PART Preparation of Materials. The pure iron used for this research was obtained from FeCIS recrystal-lized and purified by extraction with isopropylic ether. From the ferric chloride purified in this manner, hydroxide was precipitated with a solution of very pure ammonia, and, by calcination in pure sintered alumina crucibles, oxide was obtained. Reduction of the oxide to iron sponge was performed in sintered alumina tubes with very pure hydrogen at 650°C; at the end of the operation temperature was increased to 900°C. Specimens for the experiments were obtained by sintering the sponge at 1480°C in pure Hz after a pre sinter ing treatment at 900° C. It is important to note that the treatment at 1480°C in Ha produces a further purification from more volatile elements such as zinc, cadmium, arsenic, lead, and tin. Details on the preparation and characteristics of this type of very pure iron are given in a previous work.'' Only the complete analysis performed by neutron-activation methodsz3 is given here, Table I. Some of the specimens prepared in this way were carburized in the 0 region with very low amounts of carbon by treating them at 700°C in a static atmosphere of Ha containing a definite amount of CO. The set-up used is described in Fig. 1. A gas-tight quartz tube containing the specimen to be carburized and an internal friction control specimen, after being evacuated, was filled with Hz

Jan 1, 1963

By G. Venturello, C. Antonione, G. Della Gatta

Results from work on the effect of inferstitials on recovery and recrystallization of' very pure iron (99.995 pet) doped with nilrogen up to 400 ppm are reported. Nitrided specimens were obtained by heating the iron in a static atmosphere of NH3 + H2. The samples were cold-rolled 80 pet, subjected to a series of isochronal and isothermal anneals, and submitted to examination by X-rays, micrographs, and hardness tests. Small additions of nitrogen show a strong effect in reducing recovery of' the mechanical properties of high-purity iron. At the temperatures of. the experiments, this effect proved greater than in the case of carbon. At 400°C pure iron recovers more than 50 pet of the total hardness increase, carburized iron vecovers 25 pet, and nitrided iron only 10 pet. On the other hand. the addition of nitrogen has, similarly to carbon, a very small effect on recrystallization; the effect is, however, slightly higher than that of carbon. When the concentration Of nitrogen is above the solubility limit in a iron at the temperattue of the experiments, an increase in the frequency of nu -cleation is also observed. THE object of the present work is to improve knowledge on the effect of interstitials both on recovery and on primary recrystallization of pure iron. In fact. at present there are no available data on the effect of nitrogen on high-purity iron. The only work which at present can be somewhat related to this problem is a work of Leak et al.1 in which grain boundary internal friction at high temperature in the presence of increasing amounts of nitrogen is studied by a torsion pendulum. The present work is a continuation of a previous one2 on the effects of carbon. EXPERIMENTAL PART Preparation of the Material. Pure iron was prepared following the same methods used in the pre- vious work2 and was nitrided using controlled quantities of ammonia in an apparatus similar to that used for carburizing. The apparatus consists essentially of a gas-tight quartz tube containing the specimens. The tube, maintained at constant pressure by means of a mercury seal, is placed in a resistance furnace. For nitriding, the NH3 + H2 atmosphere with a suitable concentration of NH3 was introduced into the tube, which had been previously carefully evacuated and degassed by heating at 600°C. The hydrogen used was carefully purified by passing it through a palladium filter. The ammonia required was prepared with the following reaction: CaO + 2NH4CI —CaCl2 + H2O + 2NH3 by heating the mixture of CaO and NH4C1 in a glass flask and then collecting the ammonia in a graduated Hempel burette. For each nitriding program a given amount of NH3 prepared by this method was introduced together with the H2 into the tube previously evacuated. Nitriding of the sample was then performed at 570°C for 48 hr. After this, to ensure a homogeneous distribution of nitrogen, the samples were further heated for 72 hr at 800°C. With this method which uses a static nitriding atmosphere, carefully controlled conditions of purity are obtained. Contrarily, with the conventional continuous-flow methods, using large quantities of circulating gas, there is a greater risk of introducing impurities into the samples. Furthermore, the required nitrogen concentration in the specimen is easily predetermined and obtained. A plot of the relation observed between the initial concentration of NH3 in the gas and the quantity of nitrogen introduced into the iron samples is given in Fig. 1. The data refer to samples of 1.2-mm thickness and to the nitriding conditions previously described. Furthermore, as a comparison, the data relative to two 0.5-mm-thick samples are reported. The presence of a reservoir in the cold zone of the reaction bulb made possible the gradual dissociation of ammonia on the sample in the hot zone. Internal-friction methods were used to determine the content of nitrogen dissolved in the iron samples. Some analyses were also carried out with chemical methods. The following table, Table I, shows a comparison of data obtained with chemical and internal-friction methods. The correspondence between chemical methods and internal-friction

Jan 1, 1964

By W. A. Backofen, G. Y. Chin, W. F. Hosford

The effect of machine stiffness on discontinuous flow and fracture of the 2024 aluminum alloy was studied in tension at 4.2OK. An increase of machine stiffness was found to decrease the amount of elongation and drop in load during discontinuous flow, thereby postponing fracture to larger strains and higher stresses. The possibility of utilizing stiffened tools in deformation processing to suppress shear fracture originating from unstable flow was indicated. The problem of nucleating discontinuous flow and the role of the effective mass of the system in discontinuous flow were also considered. AT low temperatures the plastic flow of metals is often discontinuous, with sudden load drops and elongations.1,3 Basinski1,4 has presented strong evidence that discontinuous flow, at least in aluminum alloys, occurs under nearly adiabatic conditions. During testing the load may drop suddenly and flow become localized when the thermal softening, due to heat generated in plastic straining, is greater than the strain and strain-rate hardening. This instability criterion is more easily satisfied at low temperatures because 1) the volume specific heat is reduced so that relatively large temperature increases are possible in straining, and 2) the flow stress is relatively temperature-dependent. The important role of adiabatic shear in ductile fracture processes has been emphasized,5-1 and consideration has already been given to the influences of thermal and mechanical properties on the tendency of a material to undergo adiabatic shear.17677 By focusing attention on how the mechanical loading system influences low-temperature discontinuous flow, additional insight into adiabatic shear and its effect on fracture may be gained. EXPERIMENTAL PROCEDURE Because of its low thermal conductivity, the 2024 aluminum alloy exhibits a highly consistent discon- tinuous-flow behavior at 4.2°K and was therefore chosen as the material for study. Machined specimens of 0.113 in. diam and 1.125 in. gage length were solution heat-treated at 490°C for 3 hr, quenched into cold water, and immediately immersed in liquid nitrogen until just before testing. Testing was done at 4.2°K by immersion in liquid helium at a crosshead drive rate of 0.03 in. per min. As normally used (hard-machine basis), the spring constant of the testing machine was k = 25,000 lb per in. By inserting beam springs in series with the specimen, this value could be lowered by a factor of about 100. Details can be found elsewhere.? As a result of variable machine stiffness, the actual strain rate ranged from about 3 x 10 5 to 3 x 10-4 per sec from one test to another, as well as within any one test. However, preliminary tests had established that the tensile curves were not altered significantly by this strain-rate variation. Fig. 1 shows a typical load vs plastic-elongation curve for a solution heat-treated 2024 aluminum alloy specimen pulled in the standard hard machine (k = 25,000 lb per in.) at 4.2"K. The elastic extension has been subtracted. Plastic flow proceeded smoothly from yielding at approximately 22,000 psi (load = 220 lb) to a strain of about 4 pct at which point the flow became discontinuous. The magnitude of the load drops as well as the plastic elongation per drop increased with increasing strain until the specimen finally broke abruptly. The load-elongation behavior of a sample tested with a relatively soft machine under otherwise identical conditions is given in Fig. 2. In general, there

Jan 1, 1964

By H. I. Aaronson

Isothermally formed plates of proeutectoid a, lengthen at approximately the rates predicted by the Zener-Hillert equation, indicating that their lengthening kinetics are controlled by the volume diffusion of chromium in the ß matrix. Solution annealing treatments in the vicinity of the transus introduce a second mode of transformation, in which the lengthening rate is at least 1.8 x 104 faster than predicted by this equation. Little or no volume diffusion appears to accompany the latter transformation. The Presence of oxygen is evidently a Prerequisite for the occurrence of this reaction. X HE effects of thermal history prior to the initiation of transformations which proceed by nucleation and diffusional growth are currently evoking considerable interest. The rate of nucleation (but not the rates of growth) of pearlitel and of bainite,2 and the over-all rates of aging reactions in Al-cu3 and Al-si4 alloys have been shown to be appreciably dependent upon thermal history in the solid-solution region"' or in the two-phase region prior to the onset of pre~ipitation.3,4 In none of these reactions, however, was the transformation mechanism changed by variations in the temperature-time path used to reach the reaction temperature. Preliminary experiments reported by M. K. McQuillan5,8 and a systematic investigation by Farrar and Margolin7 have disclosed that the transformation behavior of hypoeutectoid Ti-Cr alloys is considerably more sensitive to thermal history. Qualitative evidence strongly suggests that not only the rate of nucleation but also the rate of growth and even the mechanism of the ß — a reaction can undergo remarkable changes when a solution annealing treatment in the vicinity of the ß/a +ß, or transus temperature, is interposed between a high-temperature solution anneal (conventionallq at 1000°C) and the isothermal reaction treatment. The present investigation was undertaken in an attempt to ascertain the nature and origin of these effects. Study of the changes in the kinetics and morphology of the ß - a, reaction produced by varialtions in thermal history was the primary means employed for this purpose. EXPERIMENTAL PROCEDURE The compositions of the alloys used in this in~esti~ation are given in Table I. These alloys were homogenized for 5 days at 1050° C in evacuated (2 x 10 -5 mm of Hg), zirconium-gettered fused quartz capsules. The capsules themselves were enclosed in a porcelain chamber evacuated with a mechanical pump during the homogenization anneals. Upon completion of homogenization, the alloys were cooled to room temperature and then reheated to 550°C for 3 1/2 days in order to transform the alloys to a finely divided mixture of a and TiCr2, and thus provide an approximately constant initial mi-crostructure. Individual specimens were sealed in evacuated and internally gettered Vycor capsules and heat treated as previously described.8,9 EXPERIMENTAL RESULTS Ti-10.64 Pet Cr. This investigation was largely performed on the 0.64 pet Cr alloy. The "base"

Jan 1, 1962

By F. H. Vitovec, D. W. Hoeppner

Pusk-pull fatigue tests were conducted on copper tricrystals of 99.988 pct purity to ascertain the role of grain boundaries in the initiation and propagation of fatigue cracks. Significant differences in behavior were found for specimens which possessed different transverse-boundary misorientation. In speciwens with low boundary angles cracks initiated within the transverse boundary, while higher angles led to transcrystalline fatigue failure. It is suggested that at low angular misorientation moving dislocations may interact with dislocations of the boundary or dislocations present in adjacent pains on favorably oriented glide planes, thus initiating a fatigue crack. MANY fatigue studies have been concerned with fatigue-crack initiation within grains and the mechanism causing initiation and propagation1-3 Although the initiation of fatigue cracks in or near grain boundaries of pure metals has been observed and reported in the literature, the mechanism of this phenomenon has received little attention.4"11 EXPERIMENTAL PROGRAM Testing Procedure. To investigate the role of grain boundaries regarding initiation and propagation of fatigue cracks, copper tricrystals were tested in push-pull. Axial-stress tests were used to avoid the stress gradients introduced by stressing of some other nature. Copper was selected as the most suitable test material since extensive work has been done on the formation of fatigue-induced slip in copper. Tricrystal specimens were used to provide a grain boundary geometry with one boundary transverse to the principal stress axis and one or more boundaries nearly coincident with the direction of maximum resolved shear stress. The boundary energy and the slip characteristics in the vicinity of the transverse boundary depend on the relative orientations of grains across the boundary. Testing was done at room temperature, at a frequency of 700 cpm, in an atmosphere of either air or argon. It is known that the incidence of grain boundary cracking increases with increasing temperature and decreasing frequency.4 The fatigue machine applied a uniaxial tension-compression load to the specimen by a flat spring which was actuated by an adjustable eccentric. Use was made of an adjustable head and a load cell which had strain gages mounted at 120-deg intervals around its periphery, thus providing a means for eliminating any detectable superimposed bending moment. A clip gage was mounted between the gripping heads to record the cyclic strain amplitude applied to the specimen. Each specimen's hysteresis characteristics were recorded by supplying the load and strain signals to an oscilloscope. Microstructural changes were observed and recorded with an optical microscope which was mounted on the fatigue machine. Immediately prior to insertion in the machine, each specimen was chemically polished. Extreme care was exercised while inserting the specimen in the test machine to avoid either bending the specimen or introducing a mean load. Each specimen was stressed in the tensile direction first and subsequently the load was reversed. Specimen Preparation. Tricrystal fatigue specimens of 99.988 pct Cu were grown from the melt using a modified Bridgman technique. Ingots about 1 in. high were grown to the configuration shown in Fig. 1. Upon sectioning the resultant ingot, several specimens were provided with an identical shape and grain boundary orientation. Except for plane sectioning and final polishing, this method eliminated machining the specimens. The apparatus used for growing the tricrystals is shown in Fig. 2. A spectrographically pure graphite mold, Fig. 3, was inserted in a vycor tube which was mounted on a vertical zone-refining table. Prior to insertion in the tube the mold was assembled as follows. The insert and graphite rods were fixed in position in the mold. The copper was then placed in the mold and the entire mold assembly was positioned in the vycor tube, Fig. 2. At this point the tube was sealed, evacuated, purged with helium gas, and finally placed under a slightly positive helium pressure. The heating coil was then adjusted to melt the copper charge, after which it was raised at a speed of 4 in. per hr. It is also possible to use

Jan 1, 1964

By P. J. Soltis

Direct as well as indirect evidence of a-phase ordering was found in a "near-a" type titanium alloy, Ti-8Al-1Mo-1V. The annealed alloy showed an anomalous decrease in second-stage creep rate at 950°F (510°C) and 47,500 psi. Anomalous increases were noted in initial yield stress after 500 hr creep exposure and in tensile strength after 1100 hr creep exposure. Debye-Scherrer X-ray diffraction patterns obtained on fine-grained polycrystalline speci-ment showed much line broadening and development of superlattice lines after 500 hr at 510° C. Examination with the light and electron microscopes failed to reveal phase changes in thermally exposed material, but detailed metallography is presented illustrating the plastic and fracture characteristics of the alloy. Electron-metallographic evidence is presented, however, which shows the nature of the nucleation and growth of ordered regions from the disordered a in annealed material. In the original phase diagram of the binary Ti-Al system constructed by Ogden et al.1 aluminum was shown to be soluble in a titanium over a wide temperature range at concentrations up to about 30 pct. Subsequently, a number of papers2-7 have appeared which indicate the existence of either intermetallic compounds and/or ordered phases in the a field up to 25 pct Al. In the most recent of these, Goldak and Gordon paw7 have determined unequivocally the ordered hexagonal D019 structure for Ti3Al in a 25 pct Al alloy. No superlattice lines were observed above 1112°F (600°C). Previously, the embrittle-ment encountered by Crossley and Carew4 in low- temperature heat treatments of binary Ti-Al alloys low in aluminum had been attributed to the appearance of a new phase in light micrographs. In the present work, direct as well as indirect evidence is presented showing the existence of a-phase ordering in what is essentially the binary Ti-8A1 alloy containing small percentages of the ß stabilizers molybdenum and vanadium, i.e., the "near-a" Ti-8Al-1Mo-1V alloy. Although Bohanek and Kessler8 have shown that this alloy has good stability at temperatures up to 1100°F (593°C), the present work shows instability at 950°F (510°C) where long exposure times were used. Light and electron microscopy proved very useful in revealing the mechanical behavior of ordered a and led to the conviction that ordered "near-a" alloys may have remarkably good properties and useful engineering applications.

Jan 1, 1965

By P. G. Shewmon

If interfacial equilibrium is maintained at the interface between a growing precipitate and the supersaturated matrix, so that solute diffusion alone determines the growth rate, the precipitate shape should evolve toward that characteristic of the dendrites found in solidification. However, this shape is rarely observed in precipitation reactions proceeding at high temperatures where interfacial equilibrium is usually felt to prevail. Thus some other stabilizing factor must enter, to keep the interface smooth. It is shown that a slow interfacial reaction (low interfacial mobility) will stabilize the interface, while transformation stresses have a IN studying the kinetics of phase transformations such as solidification or proeutectoid precipitation at high temperatures, it is customary to assume that equilibrium exists across the interface and that the rate of the reaction is determined by the rate at which heat and solute diffuse to and from the interface. In the case of precipitation, such an assumption predicts an almost infinite rate of initial growth. It is generally stated that the rate cannot be infinite and that during some initial period the rate must be determined not by solute diffusion but by an interfacial reaction, i.e., transferring atoms across the interface. The duration of this much weaker stabilizing eFfect and impurities tend to enhance instability. It is also concluded that a sets an upper limit on the wavelength of the perturbation that can give instability. Thus initially all flat or smoothly curved particle interfaces will be stable even if their growth is diffusion-controlled. Proeutectoid precipitation in the Fe-C system is considered in some detail and it is shown that the experimental results can only be rationalized if the growth rate of ferrite in steel transformations is determined by a slow interfacial reaction for all hut a few orientations between the two phases. initial period has never been clearly established, but it is generally assumed to be too short to affect any measurable results.' Several authors have pointed out that in the case of interfacial equilibrium any bump in the surface will grow out ahead of the planar interface due to the higher gradient in front of it.2j3 Thus the interface will be unstable with respect to an irregular interface with points (plates) propagating rapidly out ahead of the interface into the supersaturated phase. Recently, Mullins and Sekerka have given equations for the stabilizing effect of surface tenion.~ They found that for particles with a radius of curvature of 1 p or greater the stabilizing effect of surface tension will be completely overcome by a supercooling, or supersaturation, of as little as

Jan 1, 1965

By J. W. Spretnak, G. W. Cunningham

A study has been made of the growth and disappearance of voids in the interface of pressure bonded copper. The formation of visible voids is primarily due to spheroidization and coalesence of microvoids produced during the application of pressure. The microvoids could be prevented from forming by the application of high pressures or by increasing the ductility of the copper. Migrating grain boundaries were found to be more effective in void removal, than stationary grain boundaries. DURING the course of an investigation on the mechanism of pressure bonding, it was found that voids formed in the bonding interface which inhibited migration of the interfacial boundary and grain boundaries in the bond region. Therefore, an effort was made to determine the nature of the voids and how they form, grow, and disappear. This paper reports the results of such an investigation. The existence of interfacial voids is not solely a characteristic of massive components of metal which have been bonded by the application of heat and pressure, but is a phenomenon which has been observed in sintering as well. Simonsen attempted to study the sintering process by hot-stage microscopy and thereupon observed the formation of interparticle porosity as sintering proceeded. It was assumed that the porosity was due to grooves created at the location where grain boundaries joined the surface of the particle. Pranatis, Castelman, and seigle2 have also observed voids along the areas of contact in wound-wire specimens used for sintering studies. They did not discuss the point in detail since this behavior was not general, but they did suggest that the voids might develop as a result of stresses along the interparticle contact area. In previous investigations on pressure bonding, workers3 have suggested that voids may exist in the region where mating surfaces are placed in intimate contact, but the existence of the voids was not verified and no attempt was made to study the growth and disappearance of these voids. Durst noted the existence of pores in roll-clad structures prepared by cold reducing two sheets to force them in contact and then annealing to improve the bond. Since his unbonded regions contained a gas which he assumed to be insoluble, he proposed a mechanism which consisted of spheroidization of the unbonded regions and a growth of the contact area, but no speculations were made regarding disappearance of the gas filled pores. One interesting comment made by Durst was the suggestion that flattened voids with sharp corners which are produced during roll bonding will have a greater driving force for spheroidization than the more rounded pores created by pressing metal powders and thus spheroidization and neck growth will occur at lower temperatures. In this study it was necessary to demonstrate conclusively that voids can actually exist in the interfacial bond area. Experimental work was then directed toward a study of the mechanism whereby the voids grow and subsequently disappear.

Jan 1, 1963

By F. H. Wilson, E. W. Palmer

Brass mills are familiar with a recurring problem which reveals itself during deformation of annealed metal as an opening up of cracks which are suggestive of a grain boundary pattern. A typical example is seen in Fig 1, which shows part of the convex surface of a cartridge brass disc which was slightly dished by the punching operation. Another illustration of the same type of defect was found in the surface of a finished cartridge case which split open on firing. These cracks, shown in Fig 2, were away from the split but indicate the presence of the type of weakness which permitted the splitting. Usually the weakness consists of separate cracks, the lengths of which are of the same order of magnitude as the grain size prior to the final anneal. Their typical appearance in a polished section is shown in Fig 3. This structure was found below the surface of a fractured tensile-specimen that had been cut from a large cartridge blank showing the defects on its convex surface. While the pattern formed by these cracks suggests a grain boundary origin, the cracks bear no relation to the currently existing grain structure. Thus Fig 3 shows that the grains have grown up to cracks already present. Since it is doubtful that the cracks were present in the metal before the anneal, they must have formed during the anneal but prior to recrystallization. The term "fire-cracking" has been generally applied to cracking that occurs during an anneal under the influence of internal stress, but refers more specifically to obvious macroscopic cracking attributable to the presence of a low melting phase, usually lead. Since the type of cracking described above may occur when the lead content is very low, we have considered it a somewhat different phenomenon, and have called it "inter-granular parting." While most examples involve cartridge brass, intergranular parting has also been observed in the fabrication of large seamless tubes from discs of both 85/15 red brass and 70/30 cupro-nickel. Similar cracking in nickel silver was investigated by Jones and Whitehead,1 who showed that it could occur during healing or cooling. That which occurred on heating they called "fire cracking," and they suggested that, a transformation at about 320°C might account for its occurrence. It was felt in this laboratory that the observed parting was probably one aspect of the general observation, first made by Rosenhain and Archbutt,2 that a tendency toward intergranular fracture under tensile stress increases with increasing temperature and decreasing rate of strain. In this case the stress involved would be internal. The rate of strain would be exceedingly slow, a localized internal creep. Reference to the literature uncovered no efforts to extend the observations of Rosenhain to conditions involving only internal stress. Accordingly, an exploratory research, sufficient in detail to satisfy us as to the probable truth of this explanation of the observed intergranular parting, was undertaken. The internal stresses present during the early stages of an anneal (prior to recrystallization) would be from two sources: residual stresses developed during deformation, and thermal stresses caused by uneven heating and expansion. Thermal stresses would vary widely according to shape, size and manner of heating, and can be considered as supplementary to residual stresses. It seemed necessary to determine the stress and temperature conditions under which parting would occur in a relatively short time, and then to establish whether or not in- ternal stresses may persist to an extent adequate to cause parting at such temperatures. (Jones and Whitehead1 and Moore and Beckinsale3 made tests which indicated that stress relief required an appreciable time.) During the course of the research the desirability of studying the effect of grain size became apparent, and this factor is one of the major variables of our investigation. Intergranular Parting under Tension at Elevated Temperatures In early experiments, hard 70/30 brass tensile specimens, with unknown residual stresses, held for 10 min. at applied stresses from 30,000 to 40,000 psi at temperatures from 300 to 350°C, showed no macroscopically visible cracks when unloaded and cooled, but cracks very similar in appearance to those observed in commercial practice were revealed in these specimens by pulling them to fracture. Annealed specimens, on the other hand, showed no cracks in such experiments, apparently because they deformed plastically at stresses below those necessary to cause parting in a reasonable time. Hence, the specimens used for this study were first strengthened by cold tensile elongation, giving them an unavoidable residual stress pattern (determined largely by grain size and orientation) which would, however, correspond in direction, at least, to the stress pattern obtained under stress at temperature. A variation in these residual stresses might be expected with variations in grain size, but following any given anneal the reproducibility of stress pattern should be as good as that of the grain size measurement. With no information as to the effect of the amount of prior deformation, tests were conducted on specimens given the same cold elongation, using a stress applied at temperature which was a constant proportion of the stress required to produce this elongation. In

Jan 1, 1950

By Peter Greenfield, Paul A. Beck

Thirty binary systems of vanadium and chromium group transition elements with second and third long period transition elements were explored in regard to the intermediate phases formed. It was found that the phases predominating in these systems are s, AB type with ordered a-tungsten or C8 structure, close-packed-hexagonal with small unit cell dimensions and, finally, phases isomorphous with 1-manganese. IN recent years, considerable information has become available concerning the intermediate phases in binary systems of the transition elements. Thus, the s phase has been found to occur in most of the binary systems of vanadium, chromium, and molybdenum with the group of elements manganese, iron, cobalt, and nickel.' It was observed that, while the rr phases formed by chromium with manganese, iron, or cobalt possess a considerable temperature range of stability, particularly in the Cr-Co system, the corresponding s phases with molybdenum are limited to a temperature range of less than 400" above about 1200°C. Goldschmidt' reported v phases of tungsten with iron and cobalt, and these are apparently stable only at (and above?) 1400°C." Exploratory work in this laboratory with Fe-W and Co-W alloys of approximately 60 atomic pct W annealed at 1300°C did not produce X-ray patterns suggesting the presence of a phase. It appears then that the phases of iron and cobalt with the chromium group elements decrease in stability as the two components are chosen from long periods further removed from each other. From the available information, it might be concluded that the controlling factor is the increasing difference in atomic radii between the components. In contrast to the a phase, the phases formed by iron and cobalt with chromium group elements' are stable only when the latter have large atomic radii (molybdenum and tungsten); the corresponding phases with chromium do not occur. When the difference in atomic size becomes still larger (r,/r,, approaching the ideal value of 1.225), the u and p phases are replaced by Laves phases (AB,), as in the alloys of iron and cobalt with columbium," tantalum." and titanium."-" However, atomic size certainly cannot be the sole determining factor, since, for instance, in contrast to the very stable (Mo, Co)p phase, no such phase occurs in the Mo-Ni system even though the atomic diameters of cobalt and nickel are nearly the same. Similarly, chromium and cobalt form a a phase in a wide temperature range," but the corresponding s phase in the Cr-Ni system is missing. It has been shown that the composition of the u phase in various binary and ternary systems of transition elements in the first long period may be correlated in a fairly quantitative manner with the number of electron vacancies. The influence of electronic structure is probably present also in binary and ternary phases' and to some extent, apparently, even in Laves phases." " Although the absence of phases in the Cr-Ni and Mo-Ni systems has not as yet been explained on the basis of electronic structure, it appears reasonable to suspect a connection. One of the great difficulties in arriving at well founded rules in regard to the alloying behavior of transition elements lies in the lack of reliable information concerning the details of their electronic structure in the metallic and alloy form. The theoretical penetration of this field appears to be beset by very considerable difficulties, even when the complications due to alloy formation are disregarded. Another great source of uncertainty is the scarcity of phase diagram information even for binary systems of the transition elements so that only a very limited basis is provided for generalizations as to the occurrence of intermediate phases. For instance, very few binary phase diagrams of second and third long period transition element systems have so far been published. The present work was undertaken in order to survey the various types of intermediate phases occurring in 30 binary systems of elements of the group vanadium, columbium, tantalum, chromium, molybdenum, and tungsten with the elements rhenium, ruthenium, rhodium, palladium, and platinum. For most of these binary systems phase diagrams are very incompletely or not at all known, as will be further reviewed.*

Jan 1, 1957

By S. E. Haszko

Fused alumina or silica crucibles were used as the containing vessel. X-ray powder photographs were taken with CrKa radiation and the use of Straumanis type Norelco cameras of 114.6 mm diam. Crystallographic data for these compounds are shown in Table I. These results are in agreement with others of this series reported previousiy by Wernick and Geller.l The abnormally large atomic volume of Eu and Yb metal3 is manifested in EuA12 and YbAl2, when one compares them with the compounds reported in Ref. 1. However, the behavior of Yb in the Ni compound is the same as that observed in Ni5Yb having the Cu5Ca structure.4 Thus, it appears that Yb has a valence closer to 3 only in the Ni compounds; i.e.. the 2s and Id electrons are lost to the conduction band. 1,4 Europium in EuAl2, appears to have a valence closer to 2. In previous work.' X-ray patterns of ingots of NdCo2 indicated a multiphase material with faint indication of the presence of a phase having the MgCu2 structure. It was thought that NdCo2 formed peri-tectically from the melt, resulting in a multiphase system when cooled under nonequilibrium conditions. An X-ray pattern of a sample from a melt cooled more slowly than in past work showed that the major phase was NdCo2. The lattice constant, Table 1, is in excellent agreement with the value one can predict from the data of Ref 1. One of the other phases was identified as Co,Nd. The author wishes to thank J. H. Wernick for his guidance in this work, and D. Dorsi for the preparation of these compounds. 'J. H. Wernick and S. Geller: AIME Trans., in press. 'J. H. Wernick and S. E. Haszko: to be published. 'F. H. Spedding and A. II. Daane: Progress in Nuclear Energy, Series 5, Eds.: H. M. Finniston and J. P. Howe, McGraw-Hill Book Co., 1956. 'S. E. Haszko: to be published. 'J. H. Wernick and S. Geller: unpublished work. 6J. 11. Wernick and S. Geller: Acla Cryst., 1959, vol. 12, p. '162. The Influence of Hydrogen on the Lattice Parameters of Ti-Sn Alloys A. Coucoulas and H. Margolin A reinvestigation of the lattice parameters of Ti-Sn alloys by the present authors has revealed consistently higher c and a values than those obtained by Worrier. The difference is most pronounced in the c-parameters which are, therefore, used as a basis of comparison. This discrepancy was not due to air contamination, since precautions were taken to exclude this possibility. Specimens for Debye-Scherrer photograms were prepared by arc-melting 15-g buttons of Bureau of Mines titanium and 99.99 pct Sn, with compositions of 6, 8, 10, and 12 at. pct Sn. These buttons were forged under an oxygen-acetylene torch to 1/8-in. sq rods to produce relatively fine grained material. Scale and some surface were ground off, and the rods, after wrapping in molybdenum and titanium sheet, were vacuum annealed 15 min at 800 °C to remove hydrogen. Heat treatment of one of the samples at 875°C to produce ß and reveal a at the surface showed no surface contamination. Following the vacuum treatment, the specimens were wrapped in molybdenum and annealed for 1week at 800°C under two atmospheres of argon. After water-quenching, the rods were ground so that the thickness tapered to 0.1 mm at the tips. The ground specimens were then recapsuled as previously and reannealed 1 hr at 800°C to remove cold work. The

Jan 1, 1961

By James A. McGurty, Walter J. Koshuba, Samuel G. Gordon, Gilbert E. Klein

ONE of the problems encountered in working with metals at elevated temperatures is the instability resulting from solid-solid diffusion at a -common interface. A determination of the nature and magnitude of this phenomenon is important as related to structural properties of materials potentially useful in high temperature applications. This paper is concerned with the solid state reaction between metallic molybdenum and beryllium at elevated temperatures. In the older literature,' there were no known inter-metallic compounds in the system Be-Mo, and the list of beryllium intermetallics was rather small. New compilations have been made by Smithells' and by Taylor," listing all the then known beryllium binary intermetallic compounds. In addition to these, some new phases have just been reported' in the system Zr-Be and some further compounds of the type MBe,3 have been currently described. The new compound MoBe,, which is reported upon in this paper differs considerably from the above mentioned MBe13 group, and will be discussed in detail. Diffusion Study The nature of the solid diffusion at a Mo-Be interface was determined by sealing a beryllium rod inside a molybdenum capsule and heating at a temperature of 2000°F' (1100°C) for 100 hr. The molybdenum capsule was fabricated from % in. swaged molybdenum rod obtained from the Fansteel Metallurgical Corp. The beryllium metal was obtained from Brush Beryllium Corp. as % in. cold-drawn rod. This material assayed 99.05 pct Be and contained as impurities 0.84 pct Be0 and 0.19 pct Be2C. The molybdenum capsule was % in. in OD x 2 in. long. To prepare it, a concentric hole 0.250 in. + 0.001 in. — 0.000 in. in diam was drilled and reamed in one end of a rod to a depth of 1 '/2 in. A 1 in. long beryllium rod 0.250 in. + 0.000 in. — 0.001 in. in diam was pressed into the molybdenum capsule. A molybdenum plug 0.250 in. & 0.001 in. in diam x 9/16 in. long was then used to seal the beryllium in place. The capsules were placed in a molybdenum resistance furnace and heated at 2000°F (1100°C) for 100 hr. On cooling, the specimens were cut and examined metallographically. Fig. 1 is a micrograph at X250 of a portion of the interface from a transverse section. Four phases are clearly visible, with sharp boundaries between them. Phase A is a section of the molybdenum capsule; phase B is the molybdenum-rich intermetallic composition MoBe,; phase C is the beryllium-rich compound MoBe13; phase D is a section of the beryllium rod. All phases were readily polished to a high metallic luster. The molybdenum-rich phase has a pronounced purple tinge. The beryllium-rich phase (C) is only slightly darker than the pure beryllium. In polarized reflected light, however, it shows striking birefringence between crossed Nicols. The black areas represent flaws or pores in the material. A small representative amount of powdered material from each of the phases was carefully removed under the microscope with a diamond tool. With this material, powder X-ray diffraction patterns were made for the identification of each phase. Table I lists the X-ray diffraction spacings and corresponding indexes characteristic of these intermetallic compounds. Synthesis To establish the formula of the new intermetallic compound, X-ray diffraction patterns were made from powders obtained from solidified melts of known composition. The syntheses were made by

Jan 1, 1952