Search Documents

By Ronald Gibala

THE Au-Ni alloy system is one of many binary systems in which the supersaturated solid solutions may exhibit a multistaged precipitation behavior during aging. In addition to the equilibrium phase separation, which was studied extensively years ago in the range 400" to 600",' there exists at least one earlier stage of precipitation, i.e., preprecipitation, which occurs below 300°C in quenched alls.-This note reports on some effects of composition on the preprecipitation in Au-Ni alloys as determined from resistivity measurements. The kinetics of the preprecipitation were studied in alloys of 15 to 85 at. pct Ni which were water- were found in alloys which after various quenching-and-aging treatments were slowly heated and cooled (1Z"C per hr) between room temperature and about 300°C. Two such heating-cooling curves for a 40 pct Ni alloy are shown in Fig. 2. Similar effects were observed in other 15 to 50 pct Ni alloys. These curves are characterized upon heating by two changes in slope indicated by A and B in the figure and upon cooling by a resistivity hysteresis of approximately the size of the original decrease in resistivity after the aging treatment. The inflection at B generally falls at about the same temperature for all heating curves for a given alloy and appears to be a critical temperature (T,) for the preprecipitation for that alloy. The values of T, for most of the 15 to 50 pct Ni alloys fall in the range 200" to 220°C. The position of the inflection at A depends upon the heat treatment prior to the heating-cooling run and perhaps the heating rate, which was held constant in these runs. The preprecipitates grown in by the appropriate aging treatments seem to decrease in size as the alloys are heated from A to T,, dissolve at T,, and do not reappear after cooling below T,. When similar heating-cooling treatments were performed on 60 to 85 pct Ni alloys, an entirely different behavior was observed. Typical results are shown in Fig. 3 for an 85 pct Ni alloy. In these

Jan 1, 1964

By A. U. Seybolt, R. A. Oriani

The pressure and composition of the solid solution of nitrogen in chromium has been investigated as a function of temperature. The partial molal heat of solution, the activity of nitrogen in solid solution, and the partial molal free energy have been computed. The enthalpy of three reactions is summarized: N + 2Cr(3) = Cr2N(4), H° = —28,500 cal per mol 1/2N2(p) + 2Cr(8) = Cr2N(3)1 ?HO = —23,500 cal per mol 1/2N2(p) = N, ?H° = 5,000 cal per mol. WORKERS who have investigated the problem of the preparation of ductile chromium have been concerned with the effects of minor amounts of impurities upon this refractory metal. In particular, gaseous impurities such as oxygen and nitrogen have been suspected of causing trouble because of many known cases where brittleness in transition elements has been definitely traced to these elements. In order to evaluate the possible effects of the nitrogen impurity in chromium, it appeared desirable to learn something of the dependence of the nitrogen solubility upon temperature and pressure. Previous Work Maier3 in 1942 in his treatise on sponge chromium reviewed the thermodynamics of the chromium nitrides Cr2N and CrN, both of which are well-estab- lished compounds, but which apparently have not been studied in much detail. Maier presented some free energy-temperature expressions for the reactions 2 Cr,N = 4 Cr + N2 [1] and 4 CrN = 2Cr2N + N2 PI based mainly on the work of Satoh2 and Sano." Pearson and Ende3 in 1953 briefly reviewed the thermodynamics of Cr-N using the same data available to Maier, and also derived a free energy-temperature expression for reaction 1. Of the two nitrides mentioned previously, the present investigation was only concerned with Cr,N, since this nitride is in equilibrium with the metal phase, at least over most of the temperature range, Blix4 in 1929 established the structure of Cr2N (close-packed-hexagonal) by X-ray diffraction methods, and indicated that its homogeneity limits extend from 11.2 pet to 15.1 wt pet N. At a temperature of 1200°C, 38 mm Hg from the Maier expression and 43 mm Hg from the Pearson

Jan 1, 1957

By J. J. Gilman

Rates of prisnzatic plastic glide ( {1010}<2110>) in pure Cd crystals have been measured at temperatures from 158° to 276°C. The glide rate is proportional to the 2.75 power of the applied shear-stress. The activation energy is 29.2 kcal per mol. It is suggested that the rates of prismatic glide in Cd and Zn crystals are determined by the strengths of the atomic bonds across the prism planes. ALTHOUGH zinc and cadmium crystals both have hexagonal structures with nearly the same c/o ratios, their mechanical behaviors are quite different. Whereas zinc becomes quite brittle below room temperature, and cleaves readily on (0001) planes, cadmium is very ductile even at 4.2°K, and cannot be cleaved at any temperature. As part of a search for the explanation of this difference in behavior, a study has been made of prismatic glide in cadmium. It complements a previous study of the same phenomenon in zinc.1 The primary glide plane in cadmium is the basal (0001) plane, and the primary glide direction is the direction of atomic close-packing <2110>. However, if a tensile stress is applied parallel to the basal plane, then the shear stress on the basal plane equals zero so basal glide cannot occur. At low temperatures, deformation by twinning occurs; but at high temperatures, it has been found in this study that gliding on prismatic planes (1010) occurs in the close-packed direction. This is completely analogous with the case of zinc, except that lower temperatures are required. EXPERIMENTAL The experiments were done in nearly the same way as for zinc.&apos; Therefore, only the differences in the two sets of experiments will be described here; for other details the reader is referred to the previous paper. Crystals 6 by 6 mm sq were used that were grown from "Super Purity" 99.999 + pct Cd purchased from the New Jersey Zinc Co. The crystals were grown with their basal planes parallel to both the rod axis and one of the flat sides of the square cross section, A close-packed direction in the basal plane was oriented parallel to the rod axis. Gage sections were carefully machined into the crystals, and the surface damage caused by machining was removed with the same chemical polishing reagent as had been used for zinc. Thus, specimens of the same form and size as the previous zinc ones were produced. The crystals were heated to the test temperatures in a silicone oil bath (fused salts were tried first, but they reacted badly with the cadmium). An Instron tensile-testing machine was used for applying stresses to the crystals at various constant strain-rates. RESULTS The general behavior of cadmium crystals is much the same as for zinc. Only the constants that measure specific properties are different. Just as

Jan 1, 1962

By D. C. Jillson

BRIDGMAN1,2 melted metals in a graphite or hard glass tube and lowered the tube through a furnace to make it cool from one end only. Because of the difficulty of eliminating all vibration of the mold, others have raised the furnace instead. Neither way seems as desirable as a setup with no motion of either the mold or the furnace. A furnace in which both the shape and the slope of the temperature gradient could be controlled and varied over a wide range and in which such a gradient could be moved from one end of the furnace to the other, freezing the specimen from one end to the other, at any desired rate, all by means of isolated external control, seemed to offer definite advantages. In addition to eliminating the possibility of vibration due to moving parts, it might also give better control over the direction and rate of heat flow. Such an apparatus was assembled and is shown schematically in fig. 1. Equipment Furnace: A clay-carborundum tube of 3 1/2 in. ID with a % in. wall thickness was used as the core. This had a main winding of No. 12 B.&S. gauge Nichrome V with some compensation for heat loss at the ends. Taps to this winding were made at points 12 in. from each end. Fig. 2 shows details of this winding and of the two end windings. Each end winding was wound over Micanite over the main winding. No. 15 B.&S. gauge Nichrome V was used for these, and again taps were supplied at two inter-mediat,e points on each. The tube was supported in an 18 in. OD black iron shell with brick insulation. The input to each of the windings was regulated by means of a variable transformer. Temperature Regulation: A chromel-alumel thermocouple located near the furnace wall in the center of the furnace was connected with a Celec-tray controller, type PIC, 300" to 900°C range, which opened and closed a shunt across an external variable resistance in the main winding circuit. An "anticipatory response" device also was incorporated to minimize the cyclic effect of the control mechanism. Eleven survey couples in a common pyrex glass protection tube were located near the furnace wall and spaced 2 in. apart. The couple leads went to a common reference junction box where they were connected to copper leads from a selector switch which, in turn, was connected to a type K potentio-meter. This arrangement permitted rapid temperature surveys. The knob on the controller dial was replaced with a threaded brass spool turned at a controlled rate by a thin iron wire one end of which was attached to a gear train and the other to a small weight heavy enough to prevent slipping of the wire on the spool. The gear train, driven by a 1-rpm Telechron motor, contained a series of different sized interchangeable gears and threaded drums permitting a range of travel speeds from 0.10 in. per hr up to a hypo-

Jan 1, 1951

By H. P. Leighly, F. C. Perkins

THERE have been several statements in the literature about the difficulty of producing single crystals of high-purity (99.99pct) by the strain-anneal method. Consequently, investigators tend to employ low-purity aluminum for their single-crystal experiments, or else resort to the Bridgman or other techniques which depend on solidification for the production of single crystals. The following paragraphs describe a solid-state method for the manufacture of single crystals of high-purity aluminum which should provide crystals with greater perfection than those formed by solidification. The starting material for this method of producing single crystals was secured from the Aluminum Corp. of America and has a purity of 99.99 pct, the balance being trace amounts of impurities. Specimens approximately 1 by 4 in. are sheared from sheet having a nominal 0.050 in. thickness. The specimens are given a preliminary anneal at 640°C for approximately 3 hr in order to remove fabrication strains and to produce an average grain size of about 1/4-in. diam. The specimens are then etched in Tucker&apos;s etchant (45 pct HC1, 15 pct HNO3, 15 pct HF and 25 pct H2O) to remove the oxide film. Critical strain is applied by wrapping each specimen about a 1 3/4 in. round and subsequently straightening it against a flat surface. The high-purity aluminum sheet is sufficiently soft that this operation can be accomplished by ordinary finger pressure. The specimens are immediately annealed again at 640°C for 3 hr and reetched for examination. Ordinarily, considerable growth of certain of the grains will have occurred, and occasionally a single crystal will be produced on the first attempt. The procedure of alternately straining, annealing and etching is repeated until the majority of a batch of specimens contains usable crystal sizes. Typical examples are illustrated in Fig. 1. The greatest changes in crystal sizes are produced in the initial treatments. As the average crystal sizes get coarser in the later treatments, the sever- ity of the strain must be increased in order to produce grain boundary- migration. This increase in severity is effected by decreasing the diameter of the round used for straining (to 1 1/2 in., for example) and/or wrapping the specimens about the round twice, with opposite faces in contact with the round, before flattening. Usually the strain treatments described are not severe enough to produce nucleation in coarse grain high-purity aluminum. The growth of grains occurs by strain-induced grain-boundary migration. It has been observed that the grain boundaries move most readily during the first hour or so of each annealing treatment and that the rate of movement decreases with extended holding times at temperature. Prolonged annealing treatments are therefore not usually beneficial. Similarly, the rate of growth of each crystal appears to depend upon the orientation of the crystal with relation to those of its neighbors. Frequently island grains are formed after the initial heat treatment as the result of slow grain-boundary migration. These sometime become stationary during later heat treatments. Twin orientation interfaces are frequently developed during annealing. These imperfections can usually be removed by increasing the severity of strain to produce actual nucleation of new grains of more favorable orientation at the imperfection interfaces. The largest single crystals produced in our laboratory by the above method measured 4 by 1 by 0.050 in. Examination of Laue back-reflection patterns from a limited area of the specimens, gave no evidence of polygonization. Probably there is some indication of polygonization in the original grain area provided a more sensitive technique is used for detection. Experiments to produce wider specimens were less successful, possibly because wider sheets increase the complexity of the strains induced by deformation and promote widespread nucleation. Grain boundary migration occurs preferentially in a direction parallel to the longitudinal axis of the specimen. The choice of specimen geometry with respect to the rolling direction of the sheet appears to be immaterial in regard to the production of single crystals.

Jan 1, 1961

By F. V. Lenel, M. V. Rose, A. B. Backensto

WHEN aluminum-flake powders are compacted and hot pressed and the resulting compacts are extruded or hot forged, a group of materials with unique properties is obtained. Not only do they exhibit high room-temperature strength of the order of some of the aluminum alloys, but they maintain this strength even after prolonged heat treatment at temperatures up to 900°F. Moreover, their strength decreases much less with increasing temperature than that of aluminum alloys of comparable room-temperature properties. Irmann,&apos;" who discovered and first described this group of materials, which was called SAP, showed that the room-temperature mechanical properties of the extrusions are a function of the oxide content of the powders and therefore the oxide content of the extrusions. The higher the oxide content, the higher are their tensile strength, yield strength, and hardness, and the lower their ductility. Lyle" investigated the relationship between mechanical properties at elevated temperature and oxide content in the course of the development work of the Aluminum Co. of America on materials, called APMP, similar to those developed in Switzerland. He found that at 600 °F, just as at room temperatures, tensile strength and yield strength increase and elongation decreases with oxide content. A careful study of his data (Fig. 3, loc. cit.) shows, however, that the scatter is more pronounced than at room temperature. Gregory and Grant&apos;s data on the creep5 and stress-ruptureb roperties of the one commercial grade of the Swiss SAP and the various grades of APMP indicate that creep strength and stress to rupture also generally increase with increasing oxide .content. Ever since this new group of materials was discovered, attempts have been made to explain the mechanism by which they obtain their high room-temperature and particularly their elevated-temperature strength. In most of the attempts the new material was considered as a dispersion of aluminum oxide particles in a matrix of aluminum. Ir-mann, Von Zeerleder, and Rohner&apos; applied a theory on dispersion strengthening developed by Rohners to the flake-powder extrusions. According to this theory the elastic limit S, of a dispersion would depend upon the average distance between the dispersed particles L according to the equation: 2 E ¦ a where E is the modulus of elasticity and a the distance between nearest neighbors in the lattice of the matrix material. Irmann and co-workers assumed

Jan 1, 1958

By S. J. Sindeband

J. WULFF*—It seems to me that the author could improve the quality of his high temperature material by using less nickel as a cementing agent in hot pressing. Furthermore, to avoid the presence of undilfused nickel which would not be oxidation resistant, permit me to suggest that he use a nickel-chromium powder containing a small percentage of boron. This would give him a liquid phase at a lower temperature and accelerate both sintering and homogenization. The commercial alloy known ascolrnonoy contains sufficient chromium to be heat resistant and sufficient boron to be of low melting point. Such an alloy may be applicable as a cementing agent in increasing the quality of Mr. Sindeband&apos;s alloys. Finally 1 believe the author unfair to himself in expecting a porous material to have properties equivalent to one of 100 pet density. S. J. SINDEBAND—Dr. Wulff&apos;s point is well taken. Early in the program we realized the fact that we were having difficulty with these low-melting alloys, and we had hoped, since the colmonoy alloys of which you speak are at the nickel-rich end of the diagram, that by going to the other end of the diagram (chromium boride-rich) we would not have this difficulty. Thus we tried to use very small percentages of binder; but for reasons which are not exactly apparent we found that when we did this it was necessary to raise the pressing temperature to a point which we were unable to attain. For all compositions which we tried using nickel, or for that matter any nickel iron or cobalt containing material as a binder, we found that we would get low melting boride phases, which as you point out are the commercial "strength" of the hard-facing materials. 1 personally believe these owe a great deal of their behavior and even hardness to the nickel boride which is considerable evidence when an alloy of chromium boride is made with nickel. Nickel boride itself is very hard. We did try pure chromium as a binder and found there was considerable difficulty in handling it, particularly since we could not just hot press under

Jan 1, 1950

By P. W. Ramsey, D. P. Kedzie

INCREASING demand for improved strength-weight ratios made on aircraft structures has resulted in a gradual increase in the tensile strength requirements for steels used in such applications. As the cyclic loads often are more critical than static loads, and the fatigue properties are generally the design criteria, the question arises as to whether an improvement in fatigue properties accompanies the increased tensile strength. The present investigation was undertaken to determine the relationship between fatigue and tensile properties for an aircraft quality steel in the 155 to 280 ksi (1000 psi) tensile strength range, using the Prot method of fatigue testing. Procedure and Results After preliminary work to establish proper heat treating procedures for this heat of aircraft quality electric furnace steel (a Ni-Cr-Mo-V steel," AMS- Prot Fatigue Testing Method—The determination of the endurance limit by the conventional Wohler method can be time-consuming and easily require 20 specimens when statistical variance is to be established. This is also true when endurance limit loads are determined on actual parts or subassem-blies, and the desirability of a reliable accelerated method has been evident for some time. The primary advantage of the Prot method of fatigue testing is in reducing the number of specimens and the time required for each test. Unlike the Wohler method, every Prot specimen tested con- tributes to the determination of the endurance limit, and the authors have been able to duplicate Wohler results obtained with 20 specimens with only half the specimens and a fourth of the total cycles. This new technique for defining the endurance limit was proposed in 1948&apos; by Marcel Prot and consists of progressively increasing cyclic stress until fatigue failure occurs. By varying the load rate, a, a useful relationship is found to exist with failure stress, so that for steel the failure stress appears to

Jan 1, 1958

By R. D. Reiswig

An increasing amount of high-temperature metall~?~gical research is carried out in resistively heated tube furnaces in which a bare specimen is suspended by a fine wire at the midpoint of the tube. It is shown that the assumption of near-blackbody conditions on the surface of the sample may give rise to errors in optical pyrometry of 50°C or more. A number of papers published in the metallurgical literature in recent years have described the use of high-temperature tube furnaces for heat treatments, melting-point determinations, and other work. Typically, the tube is of a refractory metal with open ends, is heated by the passage of an electric current, and has concentric cylindrical radiation shields outside it. In at least one of these,&apos; the specimen is contained within a crucible having a small hole in its lid through which optical-pyrometer measurements are made under essentially blackbody conditions. In another design,* the specimen is inside a muffle which is concentric with the heater tube and which contains a number of washerlike longitudinal radi- ation shields to reduce axial temperature gradients and to give conditions near the specimen closer to those of a black cavity. Yet another design3 employs a wire specimen coaxial with the heater tube. Blackbody conditions are simulated by passing current from a separate supply through the wire until it "disappears" against the background (the inside of the heater tube) as seen through a radial spy hole in the tube. Good agreement with known melting points is achieved when an optical pyrometer is used under such disappearance conditions as the melting point is approached. That this latter method works so well is due, evidently, to considerations such as those mentioned by Dike4 and others.5-8 A more common method than the above, however, has been the suspension of an uncovered specimen by a fine wire in a resistively heated tube with open ends. A radial spy hole about midway between the ends of the tube permits optical-pyrometer observations on the specimen, the inside of the tube, or both. So observed, the specimen typically appears to differ but little in brightness temperature from the inside of the tube. According to De vos9 the radiation from such a spy hole in an empty tube of reasonable 1ength:diameter ratio (e.g., 10 or greater) should be essentially blackbody radiation. For these reasons, apparently, descriptions of work carried out in such furnaces usually include a statement to the effect that conditions surrounding

Jan 1, 1964

By D. H. Shaffer, W. F. Harris, W. M. Hickam, M. H. Loeffler

Experiments have been performed on the quantitative addition to niobium of enriched isotopes 018 and 017 at the 0.1 - 40 micro-gram level and their subsequent recovery. A measured quantity of molecular oxygen of known isotopic concentration is added to niobium metal by oxidation. Recovery of the enriched isotopes as carbon monoxide is by the vacuum fusion technique. Quantitative determinations of the enriched isotopes are made in standard volumes at constant temperature using accurately calibrated micromanometers and the mass spectrometer as pressure measuring instruments. THE presence of low concentrations of nonmetallic impurities in metals can often adversely affect the physical properties of the metal. The increase in hardness and the embrittlement of refractory metals due to oxygen is well known. In metallurgical studies dealing with the diffusion rates or the effect of oxygen on the physical properties of refractory metals, it is often necessary to add small quantities of oxygen to the metal and later recover the total quantity present. It is desirable, therefore, to establish the accuracy with which microgram quantities of oxygen can be added to niobium and recovered by vacuum fusion. The successful addition of microgram quantities of oxygen to metals by the usual manometric techniques and the subsequent recovery by vacuum fusion is difficult because of the uncertainty in the accurate determination of the quantity of oxygen originally present in the metal and because of the chance of contamination by atmospheric oxygen. In order to minimize these uncertainties earlier workers have added quantities of O16 at levels much higher than the oxygen concentrations that are of interest.&apos;-3 In order to eliminate the uncertainty associated with the O16 additions to metals at low microgram levels, experiments have been performed on the quantitative addition of oxygen highly enriched in O17 and O18 at the 0.1 to 40 pg level to niobium and the subsequent quantitative recovery of the isotopes by vacuum fusion. Since the natural abundance of O17 is 0.04 pct and of 0" is 0.2 pct this enriched oxygen provides a uniqueness from interference not achieved in earlier work.&apos;-= A measured quantity of molecular oxygen of known isotopic concentration is diffused into the metal. Recovery of the isotopes in the form of carbon monoxide is by vacuum fusion. The total quantity of gas is determined in standard volumes at constant tempera- ture using accurately calibrated Consolidated Electrodynamics micromanometers and the mass spectrometer for pressure measurements. The molecular and isotopic composition is determined mass spectrometrically. APPARATUS A schematic of the oxygen addition apparatus is shown in Fig. 1. Take-offs are provided for the attachment of the isotope container and for sample bulbs which are used to transfer samples to the mass spectrometer. Metal valves are used throughout the system including the sample bulbs in order to achieve a vacuum of 10"6 mm Hg. Evacuation is accomplished with a 3-stage oil-diffusion pump backed by a mechanical pump. A liquid nitrogen trap is used to remove condensables and to prevent oil vapor from entering the system. A micromano-meter is used for pressure measurements. The furnace assembly is shown in Fig. 2. It consists of a quartz tube joined to the apparatus through a 40/W joint with Apiezon W low-pressure wax. The furnace cap, also a 40/W pyrex joint, is provided with a pyrex hook. The sample is suspended from this hook with a platinum wire. The total volume of the furnace section is 435 ml. All volumes were determined by expanding a known volume of gas at a known pressure into the evacuated system and re-measuring the pressure. Both the micromanometer used on the oxygen addition system and the micromanometer used on the mass spectrometer were compared to a precision

Jan 1, 1961

By R. W. Kraft, F. D. George, F. D. Lemkey

From a conszderation of the geometrically possible ways in which an array of lines or linear features in three-dimensional space can depart from a statistically random arrangement, a system was developed to describe and measure different types of anisotrypic arrangements of lines in opaque solids. The technique was applied to a specimen of unidirectionally solidified Al-Cwll, eutectic which contained microstructural imperfections termed lamellar faults. Experimental data obtained from photomicrographs of different facets of a grain of this alloy were then analyzed using this system. It was deduced that the defects, which are essentially linear in natuve, were predominantly parallel to one another but not parallel to the nominal growth direction probably because of some lateral heat flow during solidification. InGOTS of lamellar eutectic alloys which have been unidirectionally solidified under growth conditions which prevent colony formation consist of large elongated grains in which the lamellae are approximately parallel to one another. Deviations from a parallel lamellar structure within a grain are caused by extra lamellae which form occasionally during the solidification process. Three-dimensional analyses of such specimens have revealed that one extra platelet produces two defects, termed 1amellar faults, which can and do grow more or less independently of one another.&apos; The faults are analogous in many ways to edge dislocations in crystals. If a lamella of one phase is considered to be basically two-dimensional, e.g., a surface, then a fault can be defined as the locus of points which delineates an edge (or half the periphery) of one extra lamella as it grows and forms bridges and saddles in an otherwise parallel arrangement oi lamellae, Fig. 1. Were it not for the fact that bridges and saddles occur in the structure, the extra platelet could be defined as the unit defect and the concept of linear faults of positive and negative character around the periphery of the extra platelet would be unnecessary. If an extra platelet is merely inserted (actually it is grown in) between other parallel platelets, the fault line around the periphery of the extra platelet would circumscribe one and only one platelet, namely the extra one, and the faults would lie in a plane parallel to the lamellae. But when an extra platelet merges with adjacent ones and each side grows independently of the other, it is no longer topologically possible to delineate "the extra plate." A fault circuit which either closes on itself or passes out of the specimen still occurs although it no longer will be coplanar with the lamellae. In fact, it is usually not even Planar even if the lamellae are. Under these conditions a concept that a specimen contains N extra platelets of a given size per unit volume would be very artificial and consequently meaningless. Therefore, because of the topological complexity of the alloys, it was deemed necessary to define one-dimensional

Jan 1, 1962

By Stanley L. Lopata, Eric B. Kula

The problem of preferred orientation has been considered in quantitative phase analysis by X-ray diffraction techniques. The average intensity of a diffraction peak can be obtained by integration over the whole pole figure, or by random rotation of the specimen in the X-ray beam, or by a combination of both. For rod or wire, where the pole figure shows rotational symmetry, the intensity is measured along a radius of the pole figure. Where no symmetry is present, rotational symmetry is imparted by rapid rotation of the sheet around its surface normal during measurement. These methods are applied to the determination of aus-tenite in an Fe-31 pct Ni rod and Fe-28 pct Ni sheet. X-RAY diffraction techniques are frequently used for quantitatively determining the relative amounts of two or more phases present in a structure.1,2 Briefly, the method requires a measurement of the intensity of a Bragg reflection for each phase. The method is based on the principle that the intensity of a Bragg reflection, IA, is directly proportional to the volume fraction of the given phase present, CA: T KRACA/2µ [1] where K is a constant independent of the diffracting phase, RA can be calculated and depends on the Bragg angle ? and the particular reflection measured, and µ is the linear absorption coefficient of the mixture.&apos; For a mixture of two phases A and B, IA = RAcA [2] IA/IB=RAcA/Rbcb and CA+ CB = 1 [3] This allows the volume fraction of a phase to be calculated directly from the measured integrated intensities of the two phases present. This method is frequently used for quantitatively determining retained austenite in steels, but can be used for the quantitative determination of in titanium alloys, as well as phases in other alloy systems. The intensities are generally measured by diffracting only from planes whose normals are perpendicular to the specimen surface, with the implicit assumption being made that this intensity is typical of reflections from planes whose normals lie at other angles to the surface. If the specimen contains a texture or preferred orientation of the crys- tallographic planes by virtue of previous mechanical working, however, this measured intensity is correct only if the intensity level fortuitously is one times random. Examination of pole figures for actual rolled sheet shows that the intensity level at the center of the figure is seldom at the random level, and can very easily differ by a factor of five or more, leading to a commensurate error in the calculated amount of the phases. Textures have been commonly found in materials which are cold-rolled or recrystallized after cold rolling. This problem is becoming of greater importance since structural materials in use today, such as the high-strength stainless steels, frequently are further strengthened by cold rolling, and hence contain textures. Although high-strength carbon-containing alloy steels generally do not contain textures, some of the newer thermomechani-cal treatments will impart a texture even in these cases. In the case of hexagonal metals, such as titanium, probably every wrought sample will show some anisotropy. Since the standard X-ray techniques are inapplicable in all these cases, there is a clear need for some method of taking this anisotropy into account. The specific problem is to obtain the integrated intensity of a Bragg reflection for each phase, averaged over all orientations of the sample with respect to the X-ray beam. This can be done either by purely mechanical means or by a mathematical averaging. Mechanically, a small spherical speci-

Jan 1, 1965

By J. H. Waxweiler, L. C. Ikenberry, R. J. Bendure

Carbon which is present as insoluble carbides in austenitic stainless steels can be measured quantitatively by dissolving the steel in iodine-methanol and analyzing the residue for carbon. Severe sen-sitization was observed in Type 302 due to precipitation of only 0.003 pet carbon. Both cold work and the presence of delta ferrite caused a marked acceleration in rate of carbide precipitation. Carbide precipitation rates in 17-7 PH were stzulied for the austenite conditioning and also the aging heat treatment. CARBON and its compounds exercise a major influence on the properties of stainless steels and their response to thermal treatment. Sensitization in 18-8 type stainless steels has been the subject of numerous investigations throughout the years. Bain, Aborn, and utherford," and Binder, Brown, Frankss all studied the effects of heating austenitic stainless steels in the temperature range of 1000° to 1500°F. The primary purpose of most of these studies was the investigation of susceptibility to in-tergranular attack in acids due to these sensitizing heat treatments. Intergranular precipitation of carbides was always associated with intergranular attack but it was recognized2 that severe attack could occur with but minute quantities of precipitated carbide. Mahla and ielsen utilized the electron microscope to make a significant contribution in illustrating the appearance and method of growth of chromium carbides during sensitizing heat treatments. However, as they stated, their studies of residues could not be used to obtain a quantitative measurement of the amount of carbon which was actually precipitated. The aim of the present investigation was to devise a relatively fast, simple method for the quantitative measurement of carbides in stainless steel. EXPERIMENTAL WORK The initial investigations were made to determine the best means of separating carbides from the matrix. A number of dissolving media were tried using both chemical and electrolytic attack. Qualitative examination of the extracted residues by X-ray diffraction indicated that solution in iodine-methanol would furnish a good means of separation. Consequently, further work was pursued along this line. The method is quite simple. The sample in the form of millings or nibblings is dissolved in iodine-methanol solution at room temperature (6-g iodine, 25-ml methanol per g of sample). The insoluble residue containing the carbides is separated by suction filtration through an ultra-fine glass filter disc. This is a very fine filter medium that will retain particles as small as 0.1 to 0.2 p in diameter. After washing with methanol and drying, the filter disc and residue are placed in a conventional combustion carbon-tube furnace and the carbon determined gravimetrically. Using this technique it was found that reproducible insoluble carbon values were obtained. However, since such small amounts of insoluble carbon were obtained on Type 302 after sensitizatipn at 1250°F and 1500°F, the values were confirmed by a second method. In the second method the sample was dissolved with copper potassium chloride and filtered through a millipore paper. This treatment dissolves the matrix but leaves undissolved practically all of the carbon irrespective of how it is present in the steel. The amount of insoluble carbon present as chromium carbide is determined by calculation from the analysis of the residue for chromium and iron. The derivation of the formula used for this calculation is discussed later. The values obtained by the indirect copper-potassium-chloride method were in agreement with those obtained by the iodine-methano1 method. See Table I. It should be pointed out that the sensitivity of the direct combustion method is not too high when the amount of carbide present is small. This is due primarily to inherent blanks and to analytical errors such as weighing. For this reason it cannot be stated with any degree of certainty that there is a significant difference between values of 0.002 and 0.005 pct. Having confirmed that the iodine-methanol extraction gave a quantitative measurement of the precipitated carbides in Type 302, exploratory tests were conducted on Armco 17-7 PH stainless steel. Samples from commercial Heat 54807 were solution annealed at 2000°F, water quenched and heated at 1250" and 1500°F, and water quenched. The analysis of Heat 54808 is as follows:

Jan 1, 1962

By O. W. Simmons, L. W. Eastwood, C. M. Craighead

Eighty-four quaternary titanium-base alloys from the following systems were investigated: 1. Titanium-chromium-carbon-nitrogen. 2. Titanium-chromium-carbon with copper, vanadium, molybdenum, manganese, iron, or nickel. 3. Titanium-chromium-nitrogen with vanadium, molybdenum, or nickel. The tensile properties, minimum bend radii, hardnesses, response to heat treatment and aging treatment, and phase relationships of these alloys are reported. HIS paper is the third in a series describing J- titanium-base alloys. The first paper describingdescribed titanium binary alloys, and the second contained data on a large number of titanium ternary alloys. Eighty-four heats, comprising three groups of quaternary titanium-base alloys, are described in this paper as follows: 1. Titanium-chromium-carbon-nitrogen alloys. 2. Titanium-chromium-carbon alloys containing copper, vanadium, molybdenum, manganese, iron, or nickel. 3. Titanium-chromium-nitrogen alloys containing vanadium, molybdenum, or nickel. The methods of preparing, fabricating, and testing the alloys are described in the paper Binary Titanium Alloys. Quaternary Titanium - Chromiurn - Carbon -Nitrogen Alloys The properties of titanium-chromium-nitrogen and titanium-chromium-carbon ternary alloys have been described in the paper Ternary Alloys of Titanium. Because small amounts of nitrogen and carbon both appear to be somewhat beneficial, these additions have been investigated fairly completely in quaternary alloys containing chromium at the following levels of composition: 2.5, 3.5, and 5.0 pct chromium 0.25 and 0.5 pct carbon 0.1 and 0.2 pct nitrogen Mechanical Properties: The mechanical properties of these alloys are listed in table I. Fig. 1 and 2 show graphically a comparison of the tensile properties and hardnesses of quaternary alloys with those of the titanium-chromium binary alloys. Fig. 1 shows the comparison at 0.25 pct carbon, whereas fig. 2 shows the comparison at 0.5 pct carbon. It is concluded from these data that 0.25 pct carbon and 0.1 pct nitrogen are desirable additions to the 5 pct chromium-titanium base. It is further concluded that most of this improvement is produced by the nitrogen and that carbon is either harmless or mildly beneficial, at least up to 0.25 pct. Structure and Transformation Range: The effects of carbon and nitrogen on the transformation range of the titanium-chromium alloys were determined as part of the routine investigation. Additions of 0.25 pct carbon and 0.1 pct nitrogen had no appreciable effect upon the transformation range. However, the addition of 0.25 pct carbon and 0.2 pct nitrogen definitely raised the beta solvus temperature, as shown by fig. 3.

Jan 1, 1951

By Sidney Fischler

Large striation-free single crystals of bismuth have been grown from the melt by rapid freezing. Zone-refined bismuth, together with doping impurities if desired, is placed in a shallow flat-bottomed graphite boat and melted in air with a propane hand torch. The torch is then withdrawn in a manner which causes the melt to freeze direction-ally. Crystallization, which resuires only a few minutes, usually results in the formation of a single crystal even when a seed crystal is not used. Crys -tals of any desired orientation may be grown by using oriented seeds. Undoped crystals grown by this method have residual resistivity ratios greater than 200. THE growth of large single crystals of bismuth by either the Czochralski or horizontal zoning technique is not entirely satisfactory. Specifically, difficulties are encountered in producing single crystals of the required dimensions in all desired orientations, and striations caused by low-angle polysynthetic twins are frequently present in the crystals. In addition, both methods are time-consuming and require special apparatus of some complexity. A simpler method has now been developed for growing large striation-free bismuth single crystals of desired orientation in a short time. Fig. 1 shows a typical setup consisting of a rectangular graphite boat which contains zone-refined bismuth, a 1/8-in.-thick flat quartz plate which covers the entire inner bottom of the boat, and three additional quartz plates about 1/4 in. thick which are used to separate the bismuth from the graphite everywhere except at a small area at the left of the boat. The graphite boat is 1 in. high, and its sides and bottom are about 1/8 in. thick. The quartz plates should be smooth and clean. The graphite boat is heated from the right with a propane torch, as shown in Fig. 1, until the bismuth is completely melted. The melt has the shape of a triangle with a narrow neck at the apex farthest from the torch. The melt is frozen direc-tionally by gradually moving the torch toward the right, away from the boat. The bismuth in contact with the graphite, at the left end of the neck, freezes first. The freezing interface then moves down the neck into the main bulk of material, where it develops a convex shape ideal for the continuation of single-crystal growth. The interface continues to move through the melt until the entire bulk is solid. The entire procedure may be completed, in air, in a matter of minutes. The technique described almost always yields a single crystal whose basal plane is nearly perpendi,cular to the bottom of the graphite boat. In earlier experiments, in which the bottom of the melt was in direct contact with the graphite boat, single crystals were grown with basal planes parallel, perpendicular, or at some intermediate angle to the bottom of the boat. At times the orientation of the bulk of the material differed from the orientation of the material in the narrow neck. In these cases, a nucleation site initiated the growth of a differently oriented crystal, and the thermal conditions favored the new orientation over the initial one. The thermal conditions depend on a number of factors, including the heating technique, the placement, shape, and thickness of the quartz plates, the thickness of the walls and bottom of the graphite boat, and the quantity of bulk bismuth employed. All of these factors, plus the initial orientation and the presence and effectiveness of nucleation sites, will determine the orientation of the final large single-crystal slab. When a crystal of specific orientation is desired, an oriented section of a rapid-freeze crystal is shaped by spark cutting and grinding for use as a seed. To grow a doped crystal, the desired impurity is placed in the graphite boat together with the bismuth chunks and seed. Crystals doped with mercury, cadmium, lead, and selenium have been grown. The rate of freezing is so great that the distribution coefficient of any impurity approximates unity. On a gross scale, therefore, impurities should be more homogeneously distributed in rapid-freeze crystals than in Czochralski or zoned crystals. Because of the possibility of constitutional supercooling, however, it is quite possible that impurities are not homogeneously distributed on a microscopic scale in the rapid-freeze crystals. Generally the single crystal slabs which have been prepared are initially 5 to 7 mm thick. Thicker crystals may be obtained by using one of these slabs as a seed. The slab is placed in a graphite boat resting on a large aluminum block, either air- or

Jan 1, 1964

By Robert Parker

Measurements of the latent heat of transformation from a to 0 titanium were made using a pulse-heating technique. Rapid heating was accomplished electrically by discharging a low-inductance capci-tor hank through a thin-strip specimen. Both high-purity titanium and titanium containing 2700 ppm of 0 were studied. An electrical-resistivity technique and a plot of energy input us temperature rise were used to monitor the phase change. It was concluded that: 1) the latent heat of transformation is 800 i 48 cal per mole; 2) phase change occurred in less than 200 sec; and 3) the percentage phase change that occurs is linearly a function of the energy available for phase change. In addition, this experiment provides a simple and inexpensive method for determining specific heat of electrical conductors over large temperature ranges. The chief advantages of this technique over past pulse-heating experiments are: 1) static measurements of capacitor-bank voltage capacitance and specimen resistance can be made quickly and accurately to determine the energy supplied to the specimen; 2) the specimen is heated so rapidly (10 µ sec) that there is no appreciable heat loss during the heating. THE purpose of this paper is to illustrate the use of the capacitor bank as a tool for basic experimental investigations and to determine the rapid phase-change kinetics of titanium. The capacitor provides a number of unique properties: 1) rapid heating rates in the order of l09oC per sec can be obtained; heating rates as slow as l04oC per sec are available by merely adding a given amount of inductance to the circuit; 2) the energy input can be precisely determined and can be varied from several joules to millions of joules, depending on the bank capacitance and voltage; 3) the specimen can be heated uniformly through the thickness and length or non-uniformly, as desired; 4) the apparatus is simple and inexpensive and can be easily altered; 5) the form of the specimen can be wires, sheets, foils, rods, and cylinders; 6) there is great precision in the timing of events; 7) this technique may be readily used in conjunction with rapid cooling.

Jan 1, 1965

By A. E. Powers, J. F. Libsch

THE simultaneous influence of time and temperature upon the tempering process in steel is well known. Hollomon and Jaffe¹ have expressed the effect of time and temperature upon the progress of tempering by a single parameter, T (c + log t); where T is the absolute temperature; t, the tempering time; and c, a constant characteristic of the steel and treatment. It was found that when hardness data for plain carbon and low alloy steels were plotted vs. this parameter, a master tempering curve was obtained which satisfied all the data for a given steel and a given hardening treatment. Roberts, Grobe, and Moersch² successfully applied the tempering parameter to various tool steels, including high speed steel for tempering times ranging from 6 min to 100 hr. The influence of tempering time and temperature upon the physical properties of high speed steel has also been extensively investigated.&apos;" Recently, the use of induction heating for very rapid tempering treatments has received attention. The authors% have shown that tempering treatments of only a few seconds duration may be successfully applied to plain carbon and low alloy steel. However, the influence of such short tempering treatments in high speed steel has not been explored. Since high speed steel is a highly alloyed steel exhibiting physical reactions during tempering that are often relatively slow and large in magnitude, it is an interesting steel for the study of tempering reactions. It was the purpose of the present investigation, therefore, to study the early progress of reactions leading to secondary hardness in high speed steel, type 6-5-4-2, and to determine if induction-tempering treatments of a few seconds duration are able to produce results equal to those of more conventional long-time tempering cycles. Experimental Details The chemical compositions for two different heats of W-Mo high speed steel used in this study are given in Table I. Table II summarizes the heat treatment given various groups of specimens cut 21/2 in. long and centerless ground to ¼ in. diam. Hardening treatments consisted of preheating to 1600°F (870°C) for V2 hr and then oil quenching from 2250°F (1230°C). Heat I was subjected to the high temperature in a salt bath for 3 min, while specimens of heat II were austenitized in a carbon-block muffle furnace for 10 min. Specimens of series E were immediately refrigerated to — 318°F (— 195°C) in liquid nitrogen following the hardening treatment to transform the major portion of the retained aus-tenite. Specimens of series F and G were subzero cooled to — 100°F (-75°C) in a dry ice-alcohol mixture. Induction tempering was performed with a Lepel high frequency converter operating at a frequency of approximately 300,000 cycles per sec. Heating cycles were controlled and recorded for each specimen using a chromel-alumel thermocouple, percussion welded to the surface of the specimen, and a modified high speed instrument with a timer previously used and described.&apos; Temperature oscillation of the specimens, while being held at the tempering temperature, was ± 15°F (8°C). Tempering Treatments: After hardening, specimens were tempered between 900" and 1500°F (480" and 815°C) to study the progress of retained austenite decomposition and secondary hardening. The specimens tempered in salt for 1 hr (series C, G, and I) were considered to represent conventional treatment and are used for comparison with rapid tempering treatments. Several induction-tempering cycles were employed: 1—flash tempering, i.e., induction heating to the tempering temperature and immediately cooling (series A, E, and F); 2—induction heating for 60 sec at temperature (series B); and 3—double-induction tempering by two successive heating and cooling cycles (series D). All specimens tempered by induction were heated at an initial rate of 450°F (250°C) per sec except those of series E, which were heated at an initial rate of 1300 °F

Jan 1, 1952

By S. E. Haszko

SEVERAL new XGa2 intermetallic compounds, Table 1, where X is a rare earth, having the AlB, structure were prepared as part of a continuing study of the magnetic and structural properties of rare-earth alloys.&apos; In this note, the crystallographic results of these compounds are presented. Chart, Eq. 121 for the data in Fig. 1 can be adequately represented by The corresponding standard free-energy change is AF; = -4.576 T log K = -20,900 + 10.20T [5I At low nitrogen concentrations the ratio of mole fraction to weight percentage is a constant so that the mole fraction X of nitrogen is given by X = 0.0392 [%NJ. At low values of X, the activity and the concearation approach each other, hence K, = 0.0392 K,, where K, is expressed in terms of the mole fraction of nitrogen. Hence Eqs. [4]. and [5] become

Jan 1, 1962

By R. E. Cech, J. H. Hollomon

KURDJUMOV and Maksimova reported experiments with manganese steels and high carbon steels&apos; and with an Fe-Ni-Mn alloy&apos; in which mar-tensite was formed isothermally over a range of temperatures. They found in some cases that mar-tensite formation could be suppressed by rapid quenching to liquid nitrogen temperature. From their microstructural observations of martensite formed isothermally, they concluded that the rate controlling step is nucleation rather than growth. Kulin and Cohen,3 in an attempt to reproduce these experiments, found that with a steel having the same composition as that reported by Kurd-jumov and Maksimova, the transformation to martensite was essentially complete above the temperature range of Kurdjumov and Maksimova&apos;s isotherms. The possible reasons for this disagreement were not considered. Recent papers by Das Gupta and Lement4 and Kulin and Speich5 report the formation of isothermal martensite in a high chromium steel and in an Fe-Cr-Ni alloy, but neither paper can be considered a verification of the original Kurdjumov and Maksimova results. Further, in neither case were the authors able to suppress the formation of martensite entirely. Because of the important bearing the Kurdjumov and Maksimova results have to an understanding of the mechanism of martensite reactions it was felt that an experimental investigation directly concerned with checking the validity of their results was in order. This paper describes the results obtained on the isothermal transformation over the temperature range from —79" to —196°C of an alloy of iron, nickel, and manganese. Experimental Apparatus A 15 lb heat of an alloy containing 73.3 pct Fe, 23.0 pct Ni, and 3.7 pct Mn was melted by induction and cast under argon. The ingot was forged to 1-in. bar and a portion rolled to 1/16x1 1/2-in. strip. This strip was pack-homogenized 300 hr at 1100" in a helium-filled sealed iron tube. The composition after homogenization was 73.2 pct Fe, 22.94 pct Ni, 3.73 pct Mn, 0.05 pct C, and 0.015 pct N. The strips were cut to 1/2-in. width for dilatometer and metal-lographic specimens. Only the center portion of the 11/2-in. strip was used in the present investigation. The dilatometer employed was similar in design to one described by Flinn, Cook, and Fellows." A concentric fused auartz rod and tube assembly with hooks for holding the specimen was mounted so as to transmit the specimen dilation to a 1/10,000 in., 1/10 in. travel dial gage. The dilatometer proper was mounted by means of extension arms to a counterweighted sliding member on a vertical standard. This method of mounting permitted rapid transfer of the dilatometer from the austenitizing furnace to the quenching bath and low temperature chamber. A small electrical vibrator on the dilatometer kept frictional effects of the quartz members at a minimum. The austenitizing unit was a vertical, molybdenum-wound, hydrogen atmosphere furnace maintained at a constant temperature ±3°C by means of constant power input. A 12-in. stainless steel jacketed copper liner having 1/2-in wall thickness acted to equalize the temperature in the hot zone of the furnace. This liner, closed at the bottom end and open at the top to permit entrance of the dilatometer and specimen, was kept filled with dry nitrogen gas. A chromel-alumel thermocouple was placed inside the tube to determine the temperature. The 4-in. dilatometer specimens in the chamber varied less than 1/2° across the specimen length except for a 1 1/20 drop at the end nearest the open end of the furnace. The low temperature isothermal holding bath was a double Dewar arrangement similar to one described by Turnbull7. The outer bath was filled with a refrigerant at a temperature lower than the desired holding temperature. The inner bath was filled with Freon "11" or "12" or a mixture of both, depending upon the holding temperature. This inner bath which tended to be cooled by the outer bath was kept at a constant temperature by introducing a small amount of heat with a manually controlled electric heater. Stirring was accomplished by bubbling dry air through the bath. A Leeds and North-rup type K potentiometer was used to measure the inner bath temperature as indicated by a five element copper-constantan thermopile. The bath temperature was maintained within ±0.2°C of the desired temperature by occasionally adjusting the heater current so as to keep the Leeds and Northrup galvanometer at zero deflection with a constant setting of the potentiometer. Isothermal tests were usually continued for 300 to 400 min and another reading made at approximately 1000 min if the bath, unattended overnight, had not deviated in temperature more than 5°C. Transformation curves are drawn dashed (Fig. 1) through the time region where temperature was not controlled precisely. Experimental Procedure Dilatometer specimens of 1/2x1/16-in. strip were cut to 41/2-in. length and holes were drilled for the quartz hooks with proper spacing to give a 4-in. measured length. A thermocouple consisting of 0.012-in. diameter chrome1 and alumel wires was spot welded to the specimen and threaded between the dilatometer rods to binding posts near the dial

Jan 1, 1954

By P. G. Shewmon, F. N. Rhines

THE determination of the self-diffusion coefficient of magnesium has been made possible recently by discovery1-1 of a radioactive isotope, Mg28 having a half-life of 21.3 hr,1 and subject to manufacture in useful quantity. In the present research this material was condensed from the vapor phase upon a surface of high purity magnesium. The progress of diffusion of the tracer atoms into polycrystalline magnesium was followed by machining layers and measuring the change in the intensity of radiation as a function of the distance of each layer from the surface. The self-diffusion coefficient was found to be 2.1 X 10-8 sq cm per sec at 627°C, 3.6 X 10-9 sq cm per sec at 551°C, and 4.4 X 10-10sq cm per sec at 468°C; the activation energy is about 32,000 cal per mol. Experimental Procedure Since there was no other published measurement of a diffusion velocity in any magnesium-base material, is was necessary to employ a number of new experimental techniques. The short half-life of Mg28 made it necessary to complete the entire experimental procedure within three or four days. This meant that the work had to be done where a cyclotron was readily accessible and that all operations, prior to the diffusion heat treatment, had to be so designed as to minimize their time requirements. Unusual problems were imposed also by the chemical reactivity of magnesium, its high vapor pressure, and the fact that no satisfactory method for elec-trodepositing magnesium on magnesium is presently available. Finally, the machining and handling of the easily air-borne radioactive-magnesium chips involved certain health hazards, resulting in the need for further experimental restrictions. Preparation of Mg28 The Mg28 was produced in the Carnegie Institute of Technology syncrocyclotron by the neutron spallation of chlorine.5 his involved bombarding a 2 gram crystal of high purity NaCl with a beam of 350 mev protons for a period of 2 hr, after which the crystal was dissolved in warm water and the Mg28 was concentrated and purified by chemical means (see Appendix). About 50 microcuries of Mg28 thus were obtained in the form of magnesium oxinate (8 hydroxyquin-olatc?), which was ignited in air to produce MgO. This in turn was reduced to magnesium metal vapor, by the method of Russell, Taylor, and Cooper," in the vacuum apparatus shown schematically in Fig. 1. Here the essential part is a tantalum ribbon, slightly dished to receive the MgO. The ribbon, pre- viously outgassed at high temperature, is heated to about 1700°C by passing an electric current through it, whereupon tantalum oxide is formed, magnesium vapor is released almost instantaneously, and condensed partly upon the diffusion sample. Diffusion-Sample Preparation: Hot-extruded magnesium rod, 21/32 in. round was used in making the diffusion specimens. The magnesium analyzed as follows: 0.004 pct Al, 0.027 pct Fe, 0.040 pct Mn, 0.0004 pct Cu, 0.0002 pct Ni, and less than 0.01 pct Ca, 0.0004 pct Pb, 0.0011 pct Si, 0.001 pct Sn, and 0.001 pct Zn. A brief study of the crystal texture of this material revealed a sharp fiber texture with the (001) plane roughly parallel to the extrusion axis. Cylindrical samples 1/2 in. long by 5/8 in. were machined from this rod, the end faces dressed on 3/0 emery, and lightly etched with 20 pct HC1 in water. These samples then were annealed for at least twice the intended time of diffusion, at the intended diffusion temperature, in order to stabilize the grain structure at about 1 mm average diameter. The annealing treatments were conducted in argon in the same apparatus and in the same manner as the subsequent diffusion treatments, which will be described presently. Thus, a strain-free plane surface was produced, but there remained a layer of MgO which had largely to be removed before the layer of Mg28 was deposited. Most of this layer was taken off by two light passes over 3/0 emery paper. The balance of the oxide and a thin layer of metal were then removed by etching 5 to 10 min in 4 pct nital (4 pct HNO3 and 96 pct ethyl alcohol) made with absolute alcohol. There followed immediately three quick rinses in: 1-49 1/2 pct methanol, 49 1/2 pct acetone, and 1 pct formic acid, 2-50 pct methanol and 50 pct acetone, and 3-pure benzene. This procedure is essentially that of Sturkey.7 The resulting surface, which was of almost elec-tropolished brightness, remained plane and was free of cold work. It could be kept clean by storing under benzene, or in a desiccator; short exposure

Jan 1, 1955