Search Documents

By L. K. Jetter, C. J. McHargue

The use of axis charts for representing the texture of cold-rolled thorium sheet was compared with conventional pole figures. Four texture components were deduced from the axis charts and shown to be consistent with the pole figures. It was shown that consideration of the pole figures alone could lead to an apparent component which is the average of two actually present. It was also shown that the spread about the "ideal" textures and the amount of material associated with each could be readily obtained Fom the axis chart method. BECAUSE of the crystallographic nature of the deformation mechanisms in metals, plastic flow results in the alignment of certain crystallographic directions with the primary flow directions. In the study of the "preferred orientation" thus developed, one wishes to discern the distribution of the crystallographic directions with respect to some reference direction, usually a direction related to the fabrication procedure, such as the rolling direction. The pole-figure method, introduced by ever,' involves the plotting of the distribution of the poles of some family of planes on a stereographic projection which places the reference direction(s) at the north pole and/or in the center. By noting the angles between the reference directions and concentrations of poles on several such pole figures, one can deduce the crystallographic directions which are aligned with the reference directions. If the preferred orientation is relatively simple and well-developed, one to three pole figures may be sufficient for obtaining the desired information; if there are several texture components, more pole figures may be needed. A significant improvement in the method of representing the textures in wires and rods resulted from the introduction of the "inverse pole figure" or axis-distribution chart by Harris.2 Such a chart gives directly the distribution of the reference axis relative to the standard stereographic projection. There has been widespread acceptance of this method for the representation of fiber textures, and methods have been proposed for converting observed diffraction intensities into axis densities.2-6 The suggestion by Mitchell and Rowland3 and Jetter, McHargue, and williams5 that sheet textures could be represented as distributions of rolling, normal, and transverse directions have been criticized on the basis that they offer no significant advantage over a combination of two ordinary pole figures and that it has not been proved that sheet textures can be treated as quasi fiber textures.6 If the purpose of a texture determination is to study some property which is related to the orientation of a particular crystallographic plane or direction, then conventional pole figures certainly are sufficient. For example, the distribution of the slip planes in face-centered cubic metals (the (111) pole figure) serves to indicate the variation in mechanical properties of sheet. On the other hand if the study is directed at an understanding of the factors influencing texture formation, it is desirable to know not only the preferred orientation but the kind and degree of spread from it and the relative amounts of material in each component, if there are more than one. Axis charts give this information as well as the orientation distributions. Consider the procedure for deducing a texture component from a pole figure for the (111) planes

Jan 1, 1961

By H. C. Fiedler

A high degree of cuhe-on-edge grain orientation and good magnetic properties were obtained in Si-Fe strip processed from laboratory heats containing vanadium nitride inclusions. The higher the nitrogen content the greater was the restraint on normal grain growth and the greater was the ability to undergo secondary recrystal-lization. The degree of restraint in a heat containing magnanese sulfide inclusions was slightly greater than that in the lowest nitrogen vanadium nitride heat. The high rate of diffusion of nitrogen in the temperature range in which the texture is developed makes it necessary to retard the loss of the inclusions until the texture has been developed. MAY and Turnbulll have shown that to develop the cube-on-edge secondary recrystallization texture in Si-Fe it is necessary that inclusions, such as manganese sulfide, be present to prevent normal grain growth. They showed that the driving force for the growth of the secondary grains is inversely proportional to the diameter of the matrix grains, and that the function of the inclusions is to maintain a small matrix grain size. Fast3has developed cube-on- edge texture in Si-Fe by nitriding the hot rolled band. The silicon nitride thereby formed promotes secondary recrystallization during the anneal of the final gage strip. To obtain the best magnetic properties, the inclusions must be removed from the strip after the grain orientation has been developed. Nitride inclusions have an inherent advantage over sulfide inclusions in that the greater diffusivity of nitrogen as comared to sulfur permits the use of shorter times and or lower temperatures for the purification heat treatment. The purpose of the work to be described was to examine the usefulness of vanadium nitride inclusions in developing the cube-on-edge texture and to determine the magnetic properties of oriented strip made from heats containing these inclusions. A comparison is made with a heat having had iden-

Jan 1, 1962

By T. P. Floridis

It was deemed desirable to obtain an understanding of the vacuum desulfurization process. McKechnie1 has reported that the sulfur content of nickel- and cobalt-base alloys is reduced in vacuo. Keverian and Taylor2 have observed that vacuum melting causes desulfurization of iron-carbon-silicon alloys. Garnyk and samarin3 have desulfurized transformer steel by vacuum treatment. Experiments were conducted in order to investigate the desulfurization of liquid iron under reduced pressures, and to establish the effect of some alloying elements, and various crucible materials. A vacuum-induction furnace of 50-lb capacity was used. The charge was Armco iron. Silicon was added as 90 pct ferrosilicon, carbon as electrode graphite, and aluminum as high-purity aluminum metal. Magnesia and silica crucibles were used, their inside diameters were 5 1/2 and 5 3/8 in., respectively. The temperature was measured with an optical pyrometer and it was held at 1600 1 15°C. Samples were withdrawn with quartz tubes of 6 mm ID, without disturbing the furnace atmosphere. Pressures were measured with an alphatron gage. The experimental results are shown in Fig. 1. They indicate that: 1) Sulfur can be removed from liquid iron alloys by vacuum treatment; 2) The desulfurization is enhanced by the presence of silicon, carbon, and aluminum, all these elements increase the activity of sulfur dissolved in liquid iron;4 3) The pronounced effect of silicon indicates that probably a volatile silicon sulfide is formed, Alcock and Richardson5 have observed a similar phenomenon; 4) The same rate of desulfurization was obtained when the metal was contained in either magnesia or silica crucibles. Dr. J. Keverian has contributed many discussions and recommendations. M. S. Sutliff has helped in conducting the heats. The permission of General Electric Co. for this publication is gratefully acknowledged.

Jan 1, 1960

By H. T. Sumsion, A. U. Seybolt

The results of an investigation of vanadium-rich V-O solid solutions are presented, indicating the structure and lattice parameters of two solutions, a and ß, and their approximate temperature-composition existence. The a solution is the terminal body-centered cubic one, and contains up to 3.2 atomic pct 0. The ß solution has an ordered body-centered tetragonal structure, is formed at 1270°C, and exists from about 15 to 22 atomic pct 0. From the evidence available, the various phase boundaries have no appreciable temperature dependence. Evidence has been found for a polymorphic transformation in pure vanadium at 1550°C. IN an earlier investigation' dealing with the preparation of pure vanadium by calcium reduction of the oxide, it was found that small amounts of oxygen drastically reduced the ductility of the metal. Because this effect was so marked, it was decided to make a study of the solubility of oxygen in solid vanadium. This report deals principally with this solubility and the nature of the phase relationships in the vanadium-rich region, particularly at temperatures below 1300 °C. However, during the investigation enough data on the V-0 system were obtained to make it appear worthwhile to present a tentative phase diagram up to the composition VO. The only significant prior work found on this system are the contributions of Klemm and Grimm,' and Mathewson et al.3 Klemm and Grimm prepared a wide range of V-O compositions by powder techniques including the compositions VO.l, VO.2, VO.3 and VO4 (9.1, 16.8, 23, and 28.6 atomic pct 0, respectively). The first three compositions were found to consist of a body-centered tetragonal solid solution, while the last also showed lines of VO (NaCl structure). They found that the parameter c, increased and the parameter a, decreased with increasing concentration of oxygen. For their composition VO.27, or about 16.8 atomic pct O, they cite the values a, = 2.948A, c, = 3.53A, and c/a = 1.2. Klemm and Grimm made no attempt to determine the solid solubility limit nor to construct a phase diagram. They did, however, give some data on the homogeneity range of VO, and they proposed a structure for the body-centered tetragonal solid solution; these points will be taken up later. Materials and Preparation of Samples The vanadium used in this investigation was prepared in the laboratory by the method previously mentioned.' A typical analysis is as follows: Fe, 0.007 pct; Si, 0.02; Ca, 0.06; C, 0.224; O2, 0.044; N,, 0.0017; H2, 0.003; and V, 99.34 ±0.3 (assay). The vanadium assay is probably low by about the error given. The impurities total about 0.36 which, if subtracted from 100, gives a purity of about 99.6. At the time material was being prepared for this work no suitable technique was available for melting vanadium without appreciable contamination. The procedure adopted therefore was to cut the calcium-reduced regulii into slices which were then rolled to strip about 0.025 in. thick for oxygen diffusion. Pieces of rolled vanadium of approximately 0.025xY4xl in. and weighing about 0.3 g were suspended in a vertical fused-silica tube which was part of an ordinary gas absorption apparatus. The silica tube was heated by an electric resistance-tube furnace which could be raised around the silica tube or lowered away from it as desired. This apparatus had no novel features which require detailed description. Other than the silica tube and furnace, it consisted of a glass system evacuated by a liquid nitrogen trapped mercury diffusion pump, a mercury-operated gas burette, a McLeod and a Pirani gage, and a mercury manometer. It was also equipped with suitably located stopcocks for isolating various parts of the system; the vacuum ordinarily attained was between 10" and 10-6 mm of mercury. Oxygen generated by decomposing MnO2 was passed through anhydrous magnesium perchlo-rate before introducing it into the gas burette and thence to the absorption chamber.

Jan 1, 1954

By P. Chiotti, G. R. Kilp

IN the study of zinc-zirconium1 and zinc-uranium2 systems, vapor-pressure measurements were made in order to establish the equilibrium phase diagrams for a pressure of 1 atm. In each of these systems, only zinc has an appreciable vapor pressure over the temperature range investigated. The zinc pressure was measured over a sufficiently wide temperature and composition range to permit calculation of the standard free energy, enthalpy, and entropy of formation for the compounds ZrZn, ZrZn2, ZrZn3, ZrZn6, ZrZn14 , and U2Zn17. In these calculations the compounds were treated as line compounds. Although the exact composition range was not determined, metallographic and thermal data indicate that the solubility range for these compounds is small. It is to be noted that the compound initially reported to correspond to the formula UZn9, 2 has been shown by the crystal structure work of Makarov and vinogradov3 to correspond to the formula U2Zn17,. The crystal structure is similar to that for the compounds Th2M17, investigated by Florio,4 et al; here M represents iron, cobalt, or nickel. Therefore, thermodynamic calculations are based on the formpla U2Zn17 EXPERIMENTAL The dew-point method employed to measure the vapor pressure of zinc over uranium-zinc alloys has been described previously.2 The same procedure and apparatus were used in measuring the zinc pressure over zinc-zirconium alloys. In the case of alloys in the two-phase region consisting of a zirconium and the compound ZrZn, the Knudsen effusion method was employed to obtain a few values in the temperature range 600" to 560°C. In most cases, tantalum crucibles were used to contain the zirconium alloys. THERMODYNAMIC PROPERTIES OFU2Zn17 A least-squares treatment of the vapor-pressure data obtained for 35 and 65 wt pct U alloys in the temperature range 650° to 940°C gave lOg10PAtm = 7,713/T + 6.33 Here, as in following equations, T represents degrees kelvin and P represents the zinc vapor pressure in atmospheres. The probable errors for the two constants were calculated to be 60.68 and 0.0563, respectively. This relation represents the equilibrium dissociation pressure for the reaction U2Zn17 (s) - 2U(s) + 17Zn(v) The solubility of zinc in solid uranium is negligible and the only additional information required to calculate the free energy of formation of U2Zn17 is the free energy of vaporization of pure zinc. K. K. Kelley5 gives the relations, AF°= 30,902 + 6.03Tlog T + 0.275 X 10-3T2 - 45.03T

Jan 1, 1961

By Glenn R. Zellars, J. P. Morris

The carrier gas method was used to measure the vapor pressure of copper over liquid copper and Fe-Cu alloys. From these results, the activity of copper in the alloys was determined at 146°, 1550°, and 1600°C. Calculations of the activity of iron were made from the results for copper. The activities of copper and iron show strong positive deviations from Raoult's law. KNOWLEDGE of vapor pressures of liquid metals has both practical and theoretical value. Fuming of metal baths is directly related to vapor pressure, and the data should bc particularly important to the technology of vacuum metallurgy. Theoretical applications include determinations of heats of vaporization, heats of solution, and activity coefficients in alloys. Methods for measuring vapor pressures of metals have been reviewed by Speiser and Spretnak.' High-vacuum procedures, such as the Langmuir and Knudsen methods, have been used most widely in recent years. However, these methods are not applicable to vapor pressures greater than lo-' mm Hg and often cannot be used in the temperature range of greatest interest. The purpose of this investigation was to develop a procedure for measuring vapor pressures of pure metals and alloys that would be applicable to pressures greater than lo-' mm Hg. The transportation or carrier gas method has been used. Copper was chosen for the initial work because its vapor pressure has been established fairly well and the reliability of the technique could be ascertained. Applicability to alloys was studied by determining the vapor pressure of copper over liquid Fe-Cu alloys. Experimental Procedure The tests were carried out in a graphite-spiral resistance furnace. The charge consisted of 50 g of metal contajned in a covered sintered-alumina crucible 1/2 in. deep and 13/8 in. ID. Two sintered-alumina tubes led from outside the furnace to within the crucible, passing through close-fitting holes in the crucible cover and radiation shield. The arrangement of the crucible and the two alumina tubes is shown in Fig. 1. The small-bore tube (1/16 in. ID by 5/16 in. OD) served as the inlet for the carrier gas. The tip of this tube touched the metal surface and the flow of gas imparted a rippling motion to the metal. In this manner the gas was brought into close contact with the metal and became saturated with metal vapor. In most of the tests the flow rate of the carrier gas was 560 ml per min, measured at room temperature. Approximately half of this saturated gas was allowed to escape from the crucible through the second alumina tube (3/16 in. ID by 5/16 in. OD) and was discharged to the atmosphere through a

Jan 1, 1957

By C. C. Herrick

The vapor pressure of indium has been measured by the torque-effusion technique, as a function of temperature between 1102o and 1422oK. For liquid indium, the vapor pressure (in atmospheres) can be represented by the equation -R In P = 5.782 x104/T - 25.29from 1000o to 1422oK. Extrapolation yields a calculated normal boiling point of 2329°K and a heat of vaporization at 298 oK of 58.09 kcal per mole by the third-law method and of 58.39 kcal per mole by the second-law method. Calculations indicate that the free-energy functions of Hultgren are to be preferred to those of Guruich. BECAUSE of the potential uses of liquid metals, it is important that convenient experimental methods be developed which will lead to a sufficient body of thermodynamic data so that reasonable estimates of properties of liquid metals can be made. Indium is particularly well-suited to investigation, since it remains liquid over a long temperature interval, it alloys readily, suitable containers for it are easily procured, and relatively few investigations of its thermodynamic properties in the region above 1000°K have been made. PREVIOUS RESEARCH The first determination of the vapor pressure of indium was made by Anderson,' using the Knudsen method and silica-lines stainless-steel cells. Kohlmeyer and spandau2 determined the normal boiling point, and a mass-spectroscopic investigation has been made by Lyubimov and Lyubitov.3 (Unfortunately, only an equation representing the data of the latter investigators has been available to us.) Hultgren et al.4 and Gurvich5 have published discordant tables of the free-energy functions for indium. EXPERIMENTAL METHOD The torsion-effusion principle has been described amply in the literature.8,7 With this method, one observes the angular deflection induced by effusion of vapor from a multihole effusion cell which is suspended from a filament producing a small rotational restoring force. The pressure within the effusion cell can be computed from the relation ziaifiai where k is the torsion constant of the filament, 6 is the observed angular deflection, and ai, fi, and qi are the area, force factor, and moment arm of the ith effusion orifice. The force factor f is analogous to the Clausing factor,' and corrects for the reduction in effusive force attributable to the finite geometry of the effusion orifice. Schultz and Searcy' have tabulated the force factors for various tube geometries. EXPERIMENTAL APPARATUS The physical arrangement employed in this study is shown in Fig. 1. The furnace elements are six Globar heat rods with 15-in. hot zones. Temperature is maintained to * 1°K by a Beck mechanism driving two 26-amp Powerstats in parallel. A Pt (Pt, Rh 10 pct) thermocouple serves as the sensing element. Four inner tubes act as vibration isolators; the air pressure required for maximum isolation was determined empirically, and is maintained by a solenoid valve. The tungsten fiber, 9 by 0.002 in., is joined to an 0.008-in. tungsten wire or graphite rod via a machined lightweight chuck.

Jan 1, 1964

By C. E. Birchenall, C L. McCabe

IN attempting to extend vapor pressure measurements of the type previously reported by Schadel and Birchenall1 for silver and by Schadel, Derge, and Birchenall' for silver-silicon to other systems, it was observed that the materials melted at indicated temperatures 10" to 15" below their accepted melting points. Further investigation revealed that the thermocouple readings were in error due to appreciable conduction losses along the reference thermocouple wires. If the wire diameter of the reference couple inserted into the Knudsen cell was reduced, the correction for the indicating couple changed in a manner tending to explain the melting behavior. When extrapolated to zero wire diameter from measurements with several reference thermocouples of different wire thickness, the melting point of silver then agreed with the indicated temperature at which silver chips were observed to coalesce into a sphere. Approximately the same calibration was given by observing the melting of small wires of silver or gold in the Knudsen cell connected in series with an ammeter, where the leads into the cell were very fine in order to minimize heat conduction. Unfortunately neither of these methods seemed to yield a sufficiently precise temperature calibration to match the apparent precision of the other aspects of the vapor pressure measurement. It was decided. therefore, to redetermine the vapor pressure of silver in another setup under conditions permitting precise temperature measurement. The vapor pressure of pure silver could then be used as an internal calibration of temperature in the older unit in making runs on alloys. This has been done; the present report is a correction to ref. 1. Experimental Procedure The apparatus, shown in Fig. 1, was very similar to that employed by Harteck,3 except that the orifice sizes were smaller and the residual pressure in the vacuum system was probably much lower. A small, sharp-edged hole, nearly circular in shape, was ground into the rounded end of a quartz tube. The orifice area was then measured by tracing the image at known magnification on graph paper and counting the squares enclosed. The silver specimen was sealed into the tube to make a Knudsen cell. A tantalum jacket surrounding the cell served to increase the uniformity of temperature. This assembly was placed in the bottom of a long quartz tube with an inside diameter of about 1 in., which was connected to the vacuum system through a ground joint sealed with picein wax well removed from the furnace. A thermocouple tube inserted through the top of the vacuum line reached into the tantalum jacket so that the thermocouple junction was immediately adjacent to the Knudsen cell except for the protection tube wall. A resistance furnace could be raised to cover the end of the quartz tube containing the cell in such a way that the cell was in the uniform temperature zone 13 in. from the end of the furnace. An ionization gage was included in the vacuum system in the cold lines of wide diameter, immediately beyond the ground joint. The vacuum system consisted of a mercury one-stage diffusion pump, backed by a Welch duo-seal mechanical pump. The pumps were separated from the reactor chamber by a dry ice trap. The ionization gage always read less than 10-5 mm Hg after initial outgassing and before each run was started. Each newly filled Knudsen cell was evacuated at high temperature overnight before the first weighing was made. The cell was returned to the system, heated for a measured time at constant temperature, cooled, and reweighed. The heating and cooling times were quite short since the hot furnace was raised to receive the reactor at the beginning of the run and removed again at the end. The tube heated or cooled quickly. The total mass loss was attributed entirely to effusion of silver vapor from the quartz cell, since empty quartz cells maintained constant mass through similar heating cycles. The vaporized silver condensed on the cold walls of the quartz tube extending above the furnace. Earlier studies in the induction heated unit had shown that the same vapor pressure was found for silver, whether the silver was in contact with the tantalum metal cell or with porcelain or quartz liners. The Pt-Pt-10 pct Rh thermocouple was calibrated against a secondary standard of the same material and found to agree with the published tables. Always operating in air at temperatures below 100O°C,

Jan 1, 1954

By E. A. Gulbransen, K. F. Andrew

Weight loss measurements were made using a sensitive microbalance operating in a high vacuum system. The Langmuir equation was used to Calculate the vapor pressures of the several metals and alloys. Aluminum lowered the vapor pressure of i9,on in a 5.4 Al-94.6 Fe alloy, and of iron and chromium in a 4.8 Al-21.5 Cr-73.7 Fe alloy. The influence of oxide films formed on the alloys on the effective vapor pressures of the alloys was also studied. These studies were used to aid in the inte9,pretation of the high temperature oxidation of alloys based on iron, chromium, and aluminum. RECENT studies on the oxidation of chromium1 and the heat resistant alloy 5 Al-22 Cr-73 Fe showed transitions in the rate of oxidation at 900o and 1050oC respectively. The transition for chromium occurred at a temperature where the rate of evaporation of chromium from oxide-free surfaces equalled the rate of chromium atoms reacting with oxygen. This paper presents new vapor pressure studies on iron, chromium, and the specially prepared alloys 5.4 Al-94.6 Fe, 21.9 Cr-78.1 Fe, and 4.8 Al-21.5 Cr-73.7 Fe. The ternary alloy is similar in basic composition to the patented heat-resistant commercial alloy known as Kanthal. The binary alloys were studied to show the individual effects of aluminum on the vapor pressure of iron and of iron on the vapor pressure of chromium. The purpose of the proposed studies was to test the influence of metal volatility on the oxidation behavior of heat-resistant alloys based on iron, chromium, and aluminum. Since oxide films formed on the metal may limit metal transfer to the surface, the influence of oxide films on metal volatility was also studied. LITERATURE A) Vapor Pressure. The vapor pressure of iron has been studied by Jones, Langmuir, and Mackay,' Dornte and Nrton. Edwards. Johnston. and Ditmar. and McCabe, Hudson, and Paton. Stull and SinkeT have calculated a heat of sublimation at 298° K of 99.83 kcalper g atom. The vapor pressure of chromium has been reported by Bauer and Brunner,' Speiser, Johnston, and Blakburn, Gulbransen and Andrew,'' Vintaikin,o McCabe, Hudson, and Paton, and Kubaschewski and Heymer.12 Good agreement was obtained except for the early work of Bauer and Brunner.' Stull and Sinke7 calculate a heat of sublimation at 298°K of 95.0 kcal per g atom. Vapor pressure measurements on aluminum have been made by Brewer and Searcy,13 Bauer and Brunner,aand Farkas.I4 Stull and Sinke,7 giving Brewer and Seary's' data the most weight, derive a heat of sublimation of 77.5 kcal per g atom at 298 oK. B) Method. Two methods15 are used for measuring the vapor pressure of metals: 1) The Langhuir free evaporation method, and 2) the Knudsen effusion method, In the Langmuir method, used in the present work, the vapor pressure of the metal P is given by the equation: Here M is the molecular weight of the vapor species. T is the absolute temperature. (dw/dt) is the rate of sublimation in g per sq cm per sec and a is the condensation coefficient. a is a measure of the efficiency of condensation of molecules striking the metal surface from the vapor. If condensation results from each collision a is unity. This coefficient has been found to be unity,a, le for metals. These results establish the general validity of the Langmuir free evaporation method as applied to metals. EXPERIMENTAL A) Vacuum Microbalance Method. A modification of the Langmuir free evaporation method was used. Strip specimens were suspended from a sensitive microbalance operating inside of a high vacuum system. For alloys, microbalance methods17 must be used on large area samples at relatively low temperatures to minimize composition changes. The

Jan 1, 1962

By B. L. Averbach, E. E. Underwood

The vapor pressure of zinc in equilibrium with solid ß AgZn alloys has been measured by the dew-point method. The thermodynamic activities of silver, and the molar heats of formation have been calculated. Similar measurements have been made for the ternary alloys formed by adding gold to AgZn. An apparent particle size effect has been observed for AgZn filings. The vapor pressure of zinc over filings is 15 to 20 pct higher than over the solid alloys. STATISTICAL methods have been used to inter pret the thermodynamic activities of the components of a solid solution in terms of average equilibrium atomic configurations. In some cases, the atomic arrangements can be measured by X-ray methods, and the results are usually expressed in terms of short range order parameters. Only in the cases of Cu³Au and AgAu have there been sufficient X-ray and thermodynamic data to verify the assumed correlation between the X-ray and the thermodynamic measurements. In Cu³Au the agreement is good; negative deviations from Raoult's law are observed and the number of Cu-Au nearest neighbor pairs predicted on the basis of the thermodynamic treatments agrees quite well with the number of such pairs observed by the X-ray methods. The ß brass alloys present a different set of conditions. The ordering is so rapid in these alloys that the disordered state cannot be retained on quenching. In contrast, the disordered state in CuAu is easily retained on quenching. On heating, the ordered ß brass loses its long range order continuously as the critical temperature is approached; in Cuau the order decreases slightly on heating and then drops discontinuously to zero at the critical temperature. These differences indicate that the short range order configurations in ß brass systems may be of a different character than in Cudu systems. However, X-ray measurements of local order cannot be made in the Cu-Zn alloys because of the similarity in scattering factors. The alloy AgZn is isomorphous with CuZn, however, and recent experiments have indicated that there is a good possibility of observing short range order in this system. Another complication arises in the case of ß AgZn. The disordered body-centered cubic structure exists above 280°C. On quenching from above this temperature an ordered structure of the cesium-chloride type is formed. On slow cooling, however, a complex hexagonal structure, the 3 phase, is produced; and if an ordered quenched alloy is reheated the phase begins to form above 80°C. It is thus difficult to study local order by X-ray methods in single crystals of AgZn since the C phase formed on heating does not necessarily return to a single crystal of the original orientation. This problem has been met, however, by adding a few percent of gold to the AgZn. The gold suppresses the formation of the c

Jan 1, 1952

By P. K. Koh, H. A. Lewis, H. F. Graff

New data on the distribution of silicon between slag and carbon-saturated iron at 1600Oand 1700OC are presented which, in combination with previously published data, permit the determination of silica activities over a broad range of compositions in the CaO-Al2O3-SiO2 system. The distribution of silicon between graphite-saturated Fe-Si-C alloys and blast furnace-type slags in equilibrium with CO has been described in previous publications.1"3 In this past work the silica-silicon relation was established at temperatures of 1425" to 1'700°C for slags containing up to 20 pct A12O3. This paper presents the results of additional studies at 1600" and 1700° C which extend the silicon distribution data at these temperatures for CaO-A12O3-SiO, slags over a range from zero pct Al2O3 to saturation with Al2O3, or CaO.2Al2O3. The upper limit of SiO2 is set by the occurrence of Sic as a stable phase when the metal contains 23.0 or 23.7 pct Si at 1600" or 1700°C, respectively. The activity of silica over the expanded range is determined directly from the distribution data.3 Recently4-7 other investigators have studied the activities of SiO, and CaO, principally in the binary system, using different methods and obtaining somewhat different results. EXPERIMENTAL STUDY The experimental apparatus and procedure have been fully described in previous publications.1, 3 Six new series of experimental heats have been made, four at 1600° and two at 1700°C. Master slags of several fixed CaO/Al203 ratios were pre-melted in graphite crucibles, and these were used with additions of silica to prepare the initial slag for each experiment. Slag and metal were stirred at 100 rpm and CO was passed through the furnace at 150 cc per min. The initial sample was taken 1 hr after addition of slag at 1600°C or 1/2 hr after addition at 1700°C. The run was normally continued for 8 hr at 1600°C or 7 hr at 1700°C, and the final sample was taken at the end of this period. Changes in Si and SiO2 content indicate the direction of approach to equilibrium, and in a series of runs where the approach is from both sides this permits approximate location of the equilibrium line. Fig. 1 shows the results of such a series of 15 runs at 1600°C for slags of CaO/Al,O3 = 1.50 by weight. Figs. 2 and 3 record other series at 1600°C and Fig. 5 a series at 1700°C with fixed CaO/Al0 ratios. The results of the experiments at 162003°C have been reported in part in a preliminary note.3 In the experiments recorded in Figs. 4 and 6, the slags were saturated with A12O3 (or with CaO.2A12O3 within its field of stability) by suspending a pure alumina tube in the melt during the course of the run. The final slag analyses were used to establish the liquidus boundaries8 in the stability fields of CaO.2Al2O3 and of Al20,. ACTIVITY OF SILICA The free-energy change in the reaction has been calculated by Fulton and chipman2 from recent and trustworthy data including heats of formation, entropies, and heat capacities. The more recent determination by Olette of the high-temperature enthalpy of liquid silicon is in satisfactory agreement with the values used and therefore requires no revision of the result which is expressed in the equation: SiO2 (crist) + 2C (graph) = Si + 2CO(g.) [1] &F° = + 161,500 - 87.4T The standard state for silica is taken as pure cristobalite and that of Si as the pure liquid metal. Since the melts were made under 1 atm of CO and were graphite-saturated, the equilibrium constant for Eq. [I] reduces to K1 = asi /asio2. The value of this constant is 1.77 at 1600°C and 16.2 at 1700°C. Through K1, the activity of silica in the slag is directly related to the activity of silicon in the equilibrium metal.

Jan 1, 1960

By Gilbert Santoro

In this study tantalum carbide filaments of various compositions in the fcc region were prepared by heating a tantalum wire in a measured amount of hydrocarbon vapor. Such properties as tensile strength, transverse-rupture strength, microhard-ness, lattice parameter, electrical resistivity, and magnetic susceptibility were measured as a function of carbon content. Some of these properties showed a maximum or a minimum between a carbon-to-tantalum molar ratio of 0.80 and 0.85, the composition range at which the color changes from metallic gray to gold. The recent literature has shown that in the large homogeneity range for the fcc phase of the Ta-C system there is a marked variation for such properties as microhardness,' electrical resistivity, ' thermodynamic properties,z'3 lattice parameter and superconductivity. In addition to the technological interest of these variations within a single phase, important theoretical benefits may ensue from a continuous investigation of properties vs stoichiometry in tantalum carbide and other refractory defect compounds, for example the effect of the metal-metal distance and crystal structure upon bond formation and electronic structure. Whether there is a similar variation of the tensile strength is of practical importance. Of theoretical interest would be the knowledge of how the magnetic susceptibility varies with carbon composition. Both of these properties, as well as the transverse-rupture strength, were determined for tantalum carbide filaments in the fcc phase region. The lattice parameter, the electrical resistivity, and the microhardness were also investigated and compared with values appearing in the literature. EXPERIMENTAL PROCEDURE Material Preparation. Tantalum carbide specimens of various carbon content were prepared by statically carburizing high-purity tantalum filaments in measured quantities of pure hydrocarbon gas. The filaments, which were 10 mil in diameter and 20 or 40 cm long, were heated by their own resistance at temperatures from 1800" to 2200°C using alternating current in some cases and direct current in others. Tantalum wire from two sources was used. One had a reported purity of 99.96 wt pct Ta. The ingot from which this wire was drawn had been electron beam-melted as the final step in its purification. The reported purity of the other wire, which was prepared by a powder metallurgical process, was 99.88 wt pct Ta. The impurities of both tantalum sources are listed in Table I. Spec-trographic-grade toluene or research-grade propane was used as the source of carbon. The apparatus for the carburization of the filaments is shown schematically in Fig. 1. The system was evacuated to 1 x l0-' mm of Hg when using the electron beam-melted tantalum and to less than 1 p when using the less-pure tantalum. Neither the difference in the base vacuum, nor in the hydrocarbon gas, nor in the tantalum filaments resulted in any detectable difference in the properties studied in this work. However, only the carbides prepared from the higher-purity tantalum were used in the magnetic-susceptibility determinations. Once the base vacuum had been reached, the system was flushed with the hydrocarbon and re-evacuated. For any desired composition of the carbide, hydrocarbon gas was allowed to leak into a constant-volume flask to a predetermined pressure. These pressures were measured by a Cartesian diver-type mercury gage with a range from 0 to 20 mm and with a scale expanded to nine times. The hydrocarbon gas was allowed into the reaction tube and the filament was quickly raised to the reaction temperature. The slack in the filament due to thermal expansion was taken up by drawing out the movable electrode with a screw mechanism. The filaments were kept at temperature from a few minutes to 200 hr. In the majority of cases the heating time was 6 hr. The reaction tube was cooled by cascading water on its outer surface. By means of an ammeter and a voltmeter the electrical resistance at the reaction

Jan 1, 1963

By A. L. Pranatis, G. M. Pound

Changes in length of copper foils of varying thickness and grain size were measured under such conditions of low stress and high temperature that it is believed that creep was predominately the result of interboundary diffusion of the type recently discussed by Conyers Herring. The surface tension of copper was calculated and results confirmed previous work within the limits of experimental error. Under the assumption of viscous flow, viscosities were calculated as a function of temperature and grain size. Predictions of the Nabarro Herring theory of surface grain boundary flow were borne out fully and the Herring theory of diffusional viscosity is strongly supported. ONLY a relatively few techniques for obtaining the surface tension of solids are presently available. Of these, the simplest and most straight forward is the direct measurement of surface tension by the application of a balancing counterforce. Thin wires or foils are lightly loaded and strain rates (either positive due to the downward force of the applied load or negative if the contracting tendency of surface tension is sufficiently greater than the applied stress) are observed. By plotting strain rates against stress, the load which exactly balances the upward pull is found and a simple calculation yields a value for the surface tension. The technique is of comparative antiquity, and solid surface tension values were reported by Chapman and Porter,' Schottky; and Berggren" in the early part of the century. Later, the filament technique became fairly well established as a method for determining the surface tension of viscous liquids, and Tammann and coworkers,'. " Sawai and co-worker and Mackh howed good agreement between the values of surface tension for glasses and tars obtained by the filament technique and by more conventional methods. With the increased confidence in the technique gained in these experiments, the method was applied to solid metals and the first reliable values of surface tension of solid metals were reported by Sawai and coworkers10' " and by Tammann and Boehme." More recently, Udin and coworkersu-'" have reported the results of experiments with gold, silver, and copper wires. Similar experiments with gold wires were carried out by Alexander, Dawson, and Kling.'" The excellent review articles of Fisher and Dunn" and of Udinl@ should be referred to for detailed criticism of the foregoing work and for discussion of underlying theory. In all the foregoing calculations, it is assumed implicitly that the material contracts or extends uni- formly along the length of the specimen and also that it flows in a viscous fashion, i.e., that strain rates are proportional to stress. For an amorphous material, such as glass, tar, or pitch, the assumptions are quite valid and good agreement is obtained with values of surface tension measured by other techniques. The values reported for metals, however, are occasionally regarded with misgiving, since it can be argued that, because of their crystalline nature, true solids can not deform in a viscous fashion. If this is true, then the results reported for solid metals over a long period of years are of only doubtful value. Thus it is clearly necessary that a mechanism be established that would explain both the viscous flow and the uniform deformation that has been assumed. Such a mechanism has been proposed by Herring."' Briefly, he suggests that, under the conditions of the experiment, deformation takes place by means of a flow of vacancies between grain boundaries and surfaces. This is a direct but independent extension of the theory proposed by Nabarro" in an attempt to explain the microcreep observed by Chalmer~.In a condensed form the Herring viscosity equation is TRL there 7 is the viscosity, T the absolute temperature, R and L grain dimensions, and D the self-diffusion coefficient. In its complete form, all constants are calculable and it includes such factors as grain shape, specimen shape, and degree of grain boundary flow. When applied to existing data, good agreement was obtained between predicted and observed flow rates. The theory received provisional confirmation from the work of Buttner, Funk, and Udin" who observed viscosities in 5 mil Au wire much higher than those in the 1 mil wire used by Alexander, Dawson, and Kling.'" More significant were the completely negligible strain rates found by Greenough" in silver single crystals. Opposed to these observations were those of Udin, Shaler, and Wulff'" who found indications of viscosity decreasing as grain size increased. Thus, complete confirmation of the theory was lacking in that the data to which it could be applied contained only a limited number of grain sizes. Hence, it was proposed that a series of experiments be carried out with thin foils of varying grain size up to and including single crystals, where, according to the Herring theory, deformation would occur only at almost infinitely slow rates.

Jan 1, 1956

By R. D. Fisher, A. G. Metcalfe, F. A. Crossley

AN investigation of the application of magnetic stirring to the consumable arc melting of aluminum and nickel demonstrated that grain refinement could be obtained when there was sufficient stirring force. Also, it was found that grain refinement could be obtained in aluminum by alternately reversing the polarity of the current through the magnetic stirring coil. The effect of the latter was to periodically reverse the direction of rotation of the molten metal.' Because of their promise, these findings were applied to conventionally cast aluminum. Shortly after this work was begun, Kondic2 reported experiments in which aluminum cast with 40° C (72° F) of superheat exhibited a grain size of 10 to 20 grains per cm2. When interrupted rotation was applied during solidification by mechanical means, a grain size of 800 to 1000 grains per cm2 was obtained. Magnetic Stirring Applied to Conventional Casting— The applicability of magnetic stirring to producing grain refinement in conventionally cast metal was evaluated in the following way. Three pounds of aluminum were cast into a clay-bonded graphite mold. The mold was surrounded by a magnetic stirring coil of 1000 turns. A direct current of 200 amp was passed through the casting by means of a graphite electrode which was immersed from the top. A current of 5 amp was passed through the stirring coil. The aluminum (1100 or 25) was superheated to 1600° F (871° C) and fluxed by passing chlorine gas through the melt for 2 min prior to casting. Two additional castings were made for comparison: 1) a conventional casting of metal superheated to 1600° F and 2) a similar casting through which 200-amp current was passed during solidification, but without current in the magnetic coil. Macrosections of these three ingots are shown in Fig. 1. Very remarkable grain refinement resulted in the magnetically stirred casting. It may be noted that the casting through which 200-amp current was passed has a coarser structure than the conventional casting. It would appear that this is due to the additional heat input generated by the current to the former casting. Mechanical Rotation Applied to Conventional Casting—A casting temperature of 1600° F was used throughout. Some 1 1/2 -lb castings rotated at 150 rpm were predominantly columnar with small areas of coarse, equiaxed grains close to the lower mold wall. Following these, a series of 3-lb castings was made. Macrosections of these ingots are shown in Fig. 2. The imposed rotational speed was 250 rpm. Turbulence or acceleration in the solidifying liquid was the significant factor. Fine grain size resulted in the material solidified during the period of acceleration of the liquid to the imposed rotational speed. When uniform rotational motion was achieved, the grain structure reverted to columnar. The final casting shown in the lower right-

Jan 1, 1962

By Harvey Cline, Donald P. Ferriss

THE violent outgassing of commercial tungsten and other refractory metals when melted in an electron beam zone refining apparatus1"3 is dealt with experimentally by one or both of two approaches. One is to provide a suitable emission current control1,2 the other is to purify the metal in the solid state before melting.4 The first of these is usually sufficient, but the authors chose also to investigate the source of the troublesome gases and to devise means of solid-state purification. Some further insights into the use of tungsten as a structural material at temperatures near its melting point were also revealed in the course of the work. One may speculate on the causes of gas formation in tungsten at high temperature by inferences from the literature and an examination of the impurities in commercial wire. Davenport5 observed microporosity in both tungsten and molybdenum filaments heated to several hundred degrees below their melting points. Studying the function of oxygen in molybdenum welds, Perry, Spacil, and wulff8 attributed similar porosity to the disproportionation of Moo2 to molybdenum metal and Moo3. Tungsten dioxide also disproportionates7 above 2000oC to yield WO3 vapor at considerable pressure. Commercial tungsten contains some 5 to 20 wt ppm O and a similar concentration of carbon depending on the details and precautions of processing. Therefore, evolution of CO is also a strong possibility as a source of gas at high temperatures. Furthermore, even for activities in the order of 0.01, it may be calculated that the pressure of CO at 3000°C would be over 4000 psi, which is in excess of the tensile strength of tungsten at this temperature.9,10 Powder metallurgy tungsten contains some 0.02 pet Fe and 0.002 to 0.005 pet of the elements Ni, Si, Al, Ca, Mn, Mg, and Mo; at temperatures over 2800°c, therefore, these elements will exhibit appreciable vapor pressure, though small compared to that of WO3 and CO. Some of these impurities may react to form high-pressure monoxides such as SiO and A10. Finally, dissolved and occluded nitrogen is an ever-present source of high-pressure gas. Commercial Type 218, General Electric filament wires, 0.025 in. diam, were heated by resistance in 10 -4 mm of Hg and in argon or hydrogen at pressures from 50 µ to atmospheric. For temperature determinations in vacuo, the Jones - Langmuir8 current-temperature relationship was employed. For gaseous atmospheres, the burn-out temperature was assumed to be the same as in vacuo so that a small, constant correction could be made for temperatures below burn-out conditions (i.e., local heating to failure). Several dozen experiments may be summarized by pointing out some structural observations. At 3050oC in 1 atm of A, porosity is very evident after 30 min, as shown in Fig. 1. For the section in Fig. 2, failure occurred 200°C below the melting point and many voids have grown in the grain bound-

Jan 1, 1962

By C. M. Schwartz, J. R. Bridge, D. A. Vaughan

THERMAL expansion coefficients of a uranium were originally reported' on the basis of X-ray diffraction measurement of lattice constants at 25°, 300°, and 650°C. These data have been reproduced by Katz and Rabinowitch.' CuK radiation had been used in this work, with consequent crowding of the patterns. Considerable overlap of the back-reflection lines was observed as the temperature was raised. Subsequent reexamination of the data led to the conclusion that errors had resulted from failure to obtain unequivocal indexing of the high angle reflections at elevated temperatures. The measurements have been repeated, using FeK radiation, which provided sufficient dispersion to assure proper indexing of the reflections, at each temperature level. The unit cell dimensions were re-determined at ten temperatures, from 25" to 650°C. Schuch and Laquer easured the macroscopic contraction from room temperature down to —253°C, and reported a negative value from —210" to —253°C; they suggested the possibility of the occurrence of a phase change. In the present work, the lattice constants of uranium have been measured down to —253°C, to test this hypothesis. Filings were prepared from a single piece of pure uranium bar stock. They were carefully cleaned with a magnet and pickled in nitric acid to remove traces of iron from the file. They were then annealed at 600°C in a sealed evacuated silica tube. The annealed filings were pickled in strong nitric acid to remove any oxide layer, washed in water and alcohol, quickly dried, and sealed in evacuated thin-walled silica capillary tubes. If properly sealed, the sample could be heated to the a-ß transforination temperature without significant buildup of the diffraction pattern of oxide. The high temperature X-ray diffraction camera was modified from the design of Hume-Rothery and Reynolds.' The thermocouple used to record the specimen temperature was calibrated from lattice-constant measurements of a standard silver specimen, using the Hume-Rothery and Reynolds values for silver over the temperature range from 25" to 700°C. Temperatures were reproducible to 210°C. Temperatures to —210°C were attained by passing precooled gas over the sample. The gas from the cooling train was directed over the sample capillary tube and thermocouple by means of a chimney of 1-mil polystyrene. The 36-gage Cu-constantan thermocouple had been calibrated by

Jan 1, 1957

By A. J. Jacobs, G. Katz

MANY of the studies of intermetallic compounds containing uranium were performed during the early 1940's under the aegis of the Manhattan Project. Subsequently, much of this work was declassified and published after 1949. In some instances this early work, completed with relatively impure materials, represents the only source of X-ray diffraction powder data available in the literature. In the case of the intermetallic compound U,Fe some discrepancies in the powder pattern exist in the literature. Since this compound has been prepared in this laboratory, it is believed that the publication of the indexed powder pattern would help clarify the conflict in the literature. In studies of the U-Fe system, Gordon and Kauf-mannl and Grogan and Clews2 independently reported the intermetallic compound U,Fe in 1950. The crystal structure was described by Baenziger, Rundle, Snow, and Wilson3 in 1950. It is isostructural with U,Mn, U,Ni, and U,Co and crystallizes in a body-centered tetragonal lattice. The lattice constants determined by Baenziger et al. are: giving an X-ray density = 17.7 g cm-3 for 4 mol per unit cell. The compound used in this study was prepared by melting a stoichiometric mixture of the constituent metals in an argon-arc furnace using a nonconsum-mable tungsten electrode. Before the argon of 99.98 pct purity was introduced into the furnace, it was passed through CaC1, to remove water vapor and afterwards through a stainless steel tube containing calcium turnings heated at 600°C for the removal of nitrogen and oxygen. The purity of the uranium used was better than 99.9 pct and that of the iron was 99.97 pct. Before and during melting a zirconium getter was used to further purify the argon atmos-

Jan 1, 1962

By C. Altstetter

THE work herein reported is restricted to the carbides which occur in quenched and tempered AISI 43XX steels with carbon contents up to 0.40 pct and silicon additions of up to 3 pct. In view of the instability and extremely small size of the carbides formed at low tempering temperatures, the technique for successfully preparing specimens for X-ray diffraction will be outlined. The alloys listed in Table I were obtained through the courtesy of the United States Steel Corp. in the form of 1/2-in. rounds forged from 100 lb. induction furnace heats (except for 4337 which was a commercial heat). The stock was normalized and then swaged and drawn to 15 mil wire with anneals at 1200F between passes. The wire was austenitized for 45 min in evacuated vycor capsules and quenched into iced brine with simultaneous smashing of the capsule. Tempering was done in air with a water quench after tempering. The carbides were extracted in a simple cell using a solution of 1M KC1 and 0.5 pct citric acid with an initial current density of 0.1 amp per sq cm. One end of a short length of wire was immersed in the solution, and the current at constant voltage was noted as a function of time. After about an hour the current dropped sharply because of the decrease in specimen cross-section. At this point it was found that the dissolution could be stopped and that the very fine wire which then resulted was just large enough to permit handling of the extracted precipitate still clinging to it, yet so small that it diffracted and absorbed only a negligible amount of the X-radiation. This rod of residue with a convenient handle of undissolved wire was rinsed in distilled water. alcohol, and acetone. Then it was dipped in a thin solution of cellulose-acetate cement and dried in vacuum. The resulting specimen was straight, uniform in density, easily handled, but most important, was completely sealed and never exposed to air. Furthermore, the residue had never been subjected to strong acids or rough handling such as in the extraction-replica technique or in the complete extraction to a powdered residue. It was found that improperly coated specimens were pyrophoric, turning to oxide with a dull red glow as they were exposed to air and yielding patterns of Fe2O3 and Fe3O4. The steels containing 3 pct Si were especially difficult to prepare for this reason. The specimens were put in a 57 mm Straumanis camera with double pinholes or slits and irradiated with filtered-chromium radiation. Readable patterns were obtained in less than an hour. A preliminary finding of some note was that for both tempered and as-quenched specimens of steels 4337 and 4337 (1.5 Si). M23C6 patterns were found along with the patterns of other constituents of the residues. This result was somewhat surprising in that previous investigators had reported that this carbide did not appear in a 0.38 pct C, 0.48 pct Mo steel1 or in chromium steels of less than about 10 pct Cr.2 Although the total amount of carbide-forming alloying elements is less than 2 pct, due to their mutual interaction and the action of the plastic deformation in promoting equilibrium, this carbide was able to form even in the steel containing 1.5 pct Si. M23C6 was not detected in the 4337 (3.0 Si) steel and the lower-carbon steels were not investigated in this condition. It is very likely then that the steels studied herein underwent a fourth stage of tempering during the anneals at 1200°F. This result has significance in that even a small amount of undissolved M23C6 in a low-carbon, low-alloy steel would exert a large effect on its hardenability. Its presence would also influence the mechanical properties by decreasing the carbon content of the matrix. Annealing in vacuum for 1 to 4 hr in the austenite field removed all traces of MZ3C+ The results on carbide precipitation during tempering, summarized in Table I, are in agreement with those of Klingler et al.3 for the higher carbon steels. For the AISI 4337 steels it is noteworthy that in the steels with added silicon the E carbide persists to longer times and higher temperatures and that silicon delays the formation of cementite. The results for the lowzr-carbon steels parallel those of the higher-carbon grade. The appearance of E carbide in the AISI 4315 is significant. There is considerable disagreem-nt in the literature as to whether this carbide forms in the tempering of steels containing less than about 0.2 pct C. Following the detection of E carbide in a 0.18 pct C plain-carbon steel,4 its occurrence in a steel containing chromium and molybdenum should be expected. The fact that the low-carbon steels have the same carbide-precipitation sequence as the high-carbon steels has bearing on the larger problem of the exact tempering reactions in all steels. Following the suggestion of Roberts et al.,' the first stage has been generally assumed to result in a metastable equilibrium of c carbide and martensite of about 0.25 pct C. From this it was concluded that a steel having less than 0.25 pct C should then be under-saturated with respect to c carbide and should not precipitate this carbide upon tempering. In view of the experimental findings of c carbide in steels hav-

Jan 1, 1962

By F. von Gemmingen, E. J. Fasiska, L. Zwell

EARLIER studies of the dependence of creep on structure1 and of the dependence of creep rupture on creep behavior2 did not include detailed discussion of the phases present in the specimens under examination. It is of interest to determine the nature and amounts of such phases present since it is well known that these are dependent on composition, heat treatment and creep conditions.3 This investigation has therefore been undertaken to identify these constituents and to determine their relative amounts. This report presents the results of this investigation and describes an improved "extraction replica" technique developed in the course of the work. The composition of the Type 316 austenitic stainless steels studied in this investigation is given in Table I. The specimens were solution treated at 2000°F for 1/2 hr and water quenched. Those specimens subjected to prestrain at room temperature Methods for extracting precipitate particles from materials for electron and X-ray diffraction analysis have been described by Fisher,4 Smith and Nutting: and Booker and coworkers.6'7 Electrolytic extraction methods have been described by Andrews and Hughes.8 The first two methods have been used at this Laboratory, but have not proved satisfactory for many problems requiring X-ray diffraction analysis. It has been difficult to remove the replicas or to avoid tearing them during removal. These difficulties are overcome by backing the replica with a water-soluble plastic such as Dupont 51-05 Elvanol (polyvinyl alcohol). The backing increases the thickness of the replica so that it can be mechanically stripped from unloosened particles without folding or tearing. This procedure eliminates the stripping of wet replicas, which usually have a low tear strength. By stripping replicas after drying, it is possible to extract partially loosened particles which otherwise would remain imbedded in the metal. The modified method is as follows: after the specimen is polished, it is etched for 60 min in modified glyceregia consisting of 30 ml glycerol, 7 ml nitric acid, and 4 ml of hydrochloric acid. The sample is then washed, air dried, and coated with a 20 pct Baker and Adamson 1611 collodion (85 pct amyl acetate by volume) film. After the collodion film is dry (about 15 min), the sample is again etched in the modified glyceregia for 50 min, washed with isopropyl alcohol (to prevent dissolving the collodion) and air dried. A very thick coat of polyvinyl alcohol (about 50 pct solution "Elvanol Dupont 51-05" in water) is poured over the sample and is permitted to dry for about 24 hr. The composite film containing the precipitates is then stripped from the specimen and floated, polyvinyl alcohol side down, in water (at about 50°C) until the polyvinyl alcohol dissolves. This usually takes about 15 min. Should any of the polyvinyl alcohol remain on the replica, it does not give a crystalline diffraction pattern and therefore does not hinder identification of the precipitates. The extraction replica, floating in water, is picked up on a glass fiber and mounted in the Debye-Scherrer camera for X-ray diffraction analysis. Concentration of the etchant, and also etching time, had to be increased for several of the samples. Fig. 1 shows two extraction replicas taken from different areas of spec. M74-37; X-ray analysis showed a strong diffraction pattern of M23C6 and a medium one of u phase. A

Jan 1, 1962

By J. A. Berger, R. J. Towner

The pjPocesses of polygonization and subgrain growth were followed in slightly stretched 99.99 pct A1 single crystals heated for cumulative times at 400°, 500°, and 600°C. Changes in sub-grain size and boundary angle were determined from measurements on X-ray micrographs. CAHN1, 2 studied polygonization in stretched and heated aluminum single crystals of 99.99 pct A1 using various techniques, including etch pits, Laue patterns, and a slight restretching of heated specimens to reveal small changes in lattice orientation by the direction of new slip lines. He found that kink bands, which had well-defined boundaries lying in a plane perpendicular to the slip direction (at least in the early stages of deformation), formed during stretching. Also, he noted that bending occurred about the <211> axis lying in the (111) slip plane perpendicular to the <110> slip direction. His studies of polygonization were largely confined to the kink bands rather than to the weakly bent matrix regions between bands. The minimum temperature required to bring about polygonization was established at about 450 "C. Guinier and Tenevin used a focusing Laue X-ray diffraction technique to study polygonization in aluminum single-crystal specimens of 99.99 pct purity. Stretching the crystals 5 pct in tension caused a widening of the focused Laue spots. After heating for 4 hr at 450°C, their method revealed no change in the specimen. Above 450°C polygonization was detected and further annealing near 600°C led to subgrain growth. They concluded that the orientation of the crystal relative to the axis of deformation had no marked effect on polygonization. Gay and Honey-combe4 using an X-ray microbeam technique found that polygonization did not occur in a stretched aluminum crystal heated at 250oC, although some decrease in the yield strength occurred. When the temperature was raised to 475oC, the asterism became broken up as a result of polygonization. Honeycombe5 noted that reflections on X-ray mi-

Jan 1, 1961