Search Documents

By Jean R. Garcia, Paulo J. R. Albuquerque, Renato P. Cunha, Osvaldo Freitas Neto

"Abstract Results obtained from in-situ load tests carried out on drilled displacement piles sunk in a porous, lateritic and unsaturated soil deposit, are analyzed in this paper. Three slow-maintained load tests were performed on deep instrumented piles with a diameter of 0.37 m and around 12 m long. The soil deposit consists of a superficial, silty clay “porous” layer 6 m thick, with an average standard penetration blow count (NSPT) of 4 and cone tip resistance and sleeve friction (qc and fs) of 1.5 MPa and 48 kPa, respectively. Under this layer there is a residual stratum 10 m thick, geotechnically consisting of a “porous” clayey silt with an average NSPT of 7 and qc and fs of 2.4 MPa and 202 kPa, respectively. The water table was reached at a depth of 17 m below ground level. The results of the field load tests yielded a maximum pile load (average for the tests) of 1428 kN, which is twice as high as corresponding experimental values from standard bored piles with similar geometric conditions. Exhumation of one of the tested piles was carried out after the test, in order to check integrity and shaft conditions. Numerical finite element analyses, using the commercially available French Code LCPC Cesar®, were performed in order to back-analyze the geotechnical soil parameters for a post execution pile condition. The results permitted a better understanding of the improvement of the subsoil given the intrinsic execution characteristics of this particular pile. It was also possible to note that drilled displacement piles have great potential to become an economically viable solution in tropical soils, given the enhanced behavior of such piles when compared to alternative (cheaper) techniques. In fact, it has several advantages which should make it a key foundation type in the Brazilian market in the future.IntroductionMost buildings in tropical soils use, as the main type of foundation, deep bored or auger type piles. These types of foundations can be performed in various ways, for example with or without soil extraction, with or without bentonite mud and so on. Two main processes maybe formulated: the first execution process is typified by bored pile types, continuous flight auger piles etc., which do not cause excessive soil displacement during excavation. With respect to the second process, one could mention, amongst others, driven piles (precast concrete or steel), Franki piles and drilled displacement piles, which do displace the soil during excavation by pushing the soil laterally around the hole in order to allow either the penetration of the pile or the excavator auger."

Jan 1, 2014

By Richard Givens, Thomas Baginski

Technological advancements in warhead designs and implementations have driven the development of arrayed initiation networks of highly accurate, highly reliable, and extremely safe detonators. Recent development efforts have produced advanced Exploding Foil Initiator (EFI) based systems that have been adapted for civilian use in commercial blasting applications.1,2,3,4,5 This novel, high technology system promises multiple improvements and advantages over the manufacturing, transportation, tracking, storage, inventory and field operation of current detonator systems. Ultimately the insertion of this technology would result in fielding a Non-Energetics Based Detonator (NEBD). Insertion of complementary technologies into the detonator’s supporting systems would greatly advance current detonator hardware/software.

Jan 1, 2011

By P. Asadollahi, M. Invernizzi

"This paper describes the innovative full-face conventional tunnel excavation technology, with its advantages in terms of savings and safety. The full-face approach has been developed throughout the experiences gained in tunnel construction. The innovative design approach is focused primarily on the deformation response of the ground acting first and foremost ahead of the face, which is analyzed, predicted and controlled by pre-confinement of the core. The advantage of this method is particularly evident in difficult grounds. This paper will present the outstanding benefits given by the adoption of the full-face approach in two projects, the “Sochi” and the “Visnove” tunnels. THEORY AND DESIGN ASPECTS OF THE FULL-FACE EXCAVATION The main challenges in tunnel and underground construction industry are gathering the design data from the ground that is being excavated and foreseeing the critical stage during construction, where the materials are in its most critical configuration. These challenges shall be addressed during excavation when the lining and the excavation disturbance have not yet reach the equilibrium. The in situ stresses in the ground are redistributed (forming an “arch-effect”) around the opening, with zones of increased stresses around the walls of the excavation (Figure 1). The distribution of the stresses can be close or far from the excavation profile, depending upon having a ground capable of withstanding the deviated stresses well or unable to withstand them, respectively. In the latter case, the ground will plasticize and deform in proportion to the volume of ground involved in the plasticization phenomenon. When the ground completely cannot withstand the stresses redistribution, it will cause the collapse of the excavation. While in the first case, the arch effect occurs naturally, in the second case, it does occur naturally only when the ground is stabilized properly. In the case of collapse, the arch-effect must be produced artificially operating on the ground prior excavation. The design should be based on the understanding of if and how the arch-effect can be mobilized during tunnel excavation and ensure that is formed by calibrating excavation and stabilization operations appropriately. The arch-effect is function of the medium that is being excavated, the action taken to excavate and the reaction expected following the excavation."

Jan 1, 2018

By Wisecarver D. W.

Today the longwall is getting increasing attention in the United States as an excellent way to mine coal. This is not to say it is the best way in every mine because conditions, capital costs, and markets may well dictate another method. However, operators with working longwalls are often showing preference by phasing out room-and-pillar sections and replacing them with longwall. In the United States there are about 90 longwalls in operating coal mines and the number is increasing. In Europe, 95% of underground coal mining is by longwall compared with only 5% in the United States. In the Western States about 25% of the underground coal mines use longwall mining. There is logic behind the increase in longwalling. Compared to room-and-pillar mining, straight single-pass longwall has important advantages that show up in underground coal mining in any part of the country.

Jan 1, 1978

By A. Modi, C. Li, R. Kabwit, W. Y. Xinchao, R. Joshi

The KIMIN copper project can treat 1.7 million dry t/a copper-cobalt ore. It has three mills in operation, two using conventional milling in water and the third in raffinate. We introduce the project process circuit and the capital and operating costs of using the raffinate process compared with conventional milling in water. There is a capital saving of approximately 11.5% for major equipment by removing the pre-leach thickener. In addition, it also achieves an annual operating cost saving of USD 2.1 million due to an increase in 49% of acidic raffinate recycled and reduction in lime consumption. The features of CITIC’s new duplex stainless-steel ball mill ,as the key equipment of the system, are also introduced

Jan 1, 2023

By Anthony T. Eyton

Intelligent Systems: Advantages for Mining ? Increased safety (reduced risk to workers) ? Increased productivity (reduced downtime) ? Reduced maintenance costs ? Customized solutions for different mines ? Growing acceptance among mine managers A Typical Precarn Project ? Meets definition of intelligent systems ? Involves at least two Precarn members ? a technology developer partner and a user partner ? in a true collaboration ? Involves at least one university and may have various other players ? Leads to a demonstrated prototype ? Costs $2-4 million, and lasts 12-30 months ? Gets up to 40% of its funding from Precarn (max. $1 m) ? Produces new intellectual property -- owned by the project team

May 1, 2002

By A. Chamanara

The gross vehicle weight (GVW) of an ultra-class mining truck comprises the unsuspended weight below the struts plus the suspended empty vehicle weight, plus the payload. Theoretically, one third of the suspended total weight is supported by two front struts and two thirds by two rear struts. However, since the payload position is not fixed when placed in the truck body and varies from load to load, compounded by uneven haul road profiles, the truck structure experiences higher than normal stresses, which manifest in the reduction of the life of the truck via structural fatigue. The downstream effects are a decrease in production and increase in operational and maintenance costs. In order to control the dynamic forces causing the high stresses on the truck structure, both the haul road conditions and the load distribution in the truck body need to be investigated. The latter aspect is the prime focus of this paper. A field test has been conducted in an oil sands mine where the Caterpillar 797B trucks are loaded by a Bucyrus 495 shovel. The strut pressure readings are collected using the data-loggers on the trucks as well as the truck velocity associated with each reading. Rack, roll and pitch are the main key performance indicators (KPIs) that are calculated to study the adverse effect of an unbalanced payload and consequently the truck structure. Finally, the shovel bucket load passes within the truck body are simulated and a new method is suggested to improve the truck payload balance.

Aug 1, 2013

Jan 1, 1966

The following pages contain valuable information about the products and services offered by our advertisers

Jan 1, 1982

By Robert L. Kidd

ONE time or another placer mining attracts the attention of a large number of people, because of the possible low initial investment, low operating cost, and quick returns. Much has been said about sampling and operating placer deposits but many are still inclined to jump at a property without giving much, if any, consideration to proper sampling. This statement does not apply to experienced mining engineers but I am hoping that readers will tear out this article and pass it along where it will do the most good and thus help to preserve the reputation of legitimate mining. It would appear that some people have an ability to sink test pits in high-grade gravel that is positively uncanny. One pit showing high-grade values proves to some property owners and promoters that the entire property will do the same. This is

Jan 1, 1937

By Henry Howe

(New York Meeting, October, 1913.) The Equilibrium. Position of A 1.-Some of the most important data on this subject are collected in Table I. Definition of Ae 1-Just as we call A 1 of rising temperature Ac 1, and that of falling temperature Ar 1, so we may give the symbol Ae 1 to the equilibrium position of A 1. Preliminary Assumptions.-In deciding what weight to assign the various data, and indeed what data are to count, three assumptions should be made. These are: 1. The corollary from the phase rule, that the temperature of Ae 1 is constant and independent of the carbon content, though, of course, it may be changed by the presence of other elements. 2. That because neither in heating nor in cooling can the transformation begin before the temperature reaches Ae 1, though it may be delayed by lag till after the temperature has passed beyond Ae 1, therefore Ae 1 should be at or below the observed beginning of Ac 1 and at or above the observed beginning of Ar 1, and, a fortiori, it should be at or below the observed maximum of Ac 1, and at or above the observed maximum of Ar 1. It may be necessary to take these maxima into consideration in view of the experimental difficulty of detecting these beginnings.

Jan 6, 1913

By Paul Richardson

This paper discusses the drilling techniques and equipment used by Loffland Brothers Company to drill the AEC's UC-3 large diameter shaft in Nevada. Included are pictures and illustrations of the drilling-mud circulating system, the surface and downhole drill-string and the special heavy-duty mast and hoisting equipment required to do the job. The purpose and method of lining the large diameter holes along with the technique and materials used to backfill the lining to hole annulus are discussed briefly. Areas requiring improvement in both equipment design and technology for large diameter shaft drilling are discussed briefly. Shafts as large as 140 inches in diameter to depths of 5,000 feet can be drilled with existing equipment and technology.

Jan 1, 1969

The Canadian concept for nuclear fuel waste disposal is being assessed by AECL Research in a series of experiments at its Underground Research Laboratory (URL) near Lac du Bonnet. Manitoba, Canada. As pan of this research, the Mine-by Experiment has been designed to obtain information on rock mass behavior, the development of an excavation-induced damage zone and failure mechanisms around a circular bored tunnel. An iterative design approach was used to effectively reconcile the experiment objectives and construction logistics. This paper discusses the design considerations and construction methodology adopted on the project.

Jan 1, 1991

By S. Thibeault, P. Filiatreault, B. Straight, D. Castendyk, L. Cameron

"Unmanned aerial vehicles (UAV), or drones, capable of collecting and retrieving water samples from pit lakes, tailings ponds and other mine water basins will revolutionize environmental programs by lowering sampling costs and reducing safety related risks. Costs typically include a boat and associated equipment, boat transportation, road maintenance, water safety devices, water safety training, and additional staff. Typically, the total cost can exceed $20,000 USD per sampling event (excluding lab analyses). Hazards include potential for drowning, unstable pit walls, and unconsolidated sediment surrounding tailings ponds. Hatch has developed a novel device for aerial drones which currently enables the collection of water samples from depths up to 390 ft (119 m). This system only requires a pilot, a sample technician, and a safe operations point overlooking the water body. Hatch anticipates this will reduce monitoring cost by at least 50% while improving safety, reducing staffing requirements and accelerating data acquisition. This manuscript demonstrates profiling and sample collection from a 95 ft (29 m) deep reservoir and a 377 ft (115 m) deep pit lake, and highlights the potential of this emerging technology. INTRODUCTION Working on or near water at active, closed, or abandoned mine sites is inherently dangerous. Between 1996 and 1999, the United States Mine Safety and Health Administration (MSHA) reported 17 fatalities involving drowning at US metal, non-metal, and coal mines (MSHA, 2000). Open pit mines which fill with water following mine closure, called pit lakes, present numerous risks to environmental monitoring teams including drowning, hypothermia, falls to the ground from the top of high walls, and rock avalanches resulting from steep, unstable pit walls. Some pit lakes are simply not easily accessible for ongoing monitoring. However, the routine collection of water samples from the entire water column on at least an annual basis is required to monitor the evolution of water quality over time, to verify the accuracy of numerical predictions, and to manage lake water chemistry in order to produce “treatable” influent to water treatment plants, and ultimately, produce acceptable site discharge water quality. As a product of these risks and the need for water sample, mining companies spend considerable expense on pit lake safety as part of monitoring. This includes training personnel for “on water” duties and hazards, purchasing or hiring specialized equipment and personnel (such as boats, boat operators, personal floatation devices, and mustang suits), stabilizing pit walls and maintaining safe access roads to the lake surface, employing spotters with direct communication to emergency medical services to watch sampling activities (because cell phones and radio signals can be blocked by pit walls), and utilizing redundancy to prepare for unexpected incidents and accidents. For example, one Canadian mining company requires pit lake water samplers to hold Marine Emergency Duties (MED) training to ensure the entire boat crew is sufficient and competent for the safe operation of the vessel, and uses three boats for water sampling: two on the water at all times, and one on the shoreline, ready to deploy. The costs of these safety mechanisms greatly adds to the overall expense associated with pit lake sampling. Consequently, environmental programs may need to reduce the frequency of pit lake sampling in order to keep monitoring programs within an acceptable budget"

Jan 1, 2017

By Staff

One hundred thousand miles of flying over the North country without a single air casualty; much of it over virgin territory probably never before visited by white men; some of it over regions that abound with possibilities for minerals; all of it effective, for exploration and the establishment of bases and supply-stations, and for the carrying of men and their tools and provisions- this, briefly, is the record of Northern Aerial Minerals Exploration, Limited, a Canadian company organized Jess than nine months ago, which has been functioning, without interruption, during spring, summer, and now into winter. Our planes have ranged from the Alaskan boundary on the west to the Labrador coast on the east, and from the Transcontinental railway north to the Arctic circle. Our prospectors, carried on trips of hundreds, and occasionally thousands, of miles, have gone over large sections of country which were never before explored, and at the end of the prospecting season the Company finds itself in possession of several groups of important gold claims, which look most promising. In addition to this, we have been in contact with deposits of almost every known mineral.

Jan 1, 1929

By BARRY BANNATYNE

Ombrotrophic Sphagnum peat bogs have a characteristic signature on both colour injrared film (750 nm to 3,000 nm response) and Daedalus injrared line-scanner images (thermal infrared 3 to 5 microns and 8 to 14 microns response). This remote sensing method was used to survey bogs in southeast Manitoba to delineate targets for surface exploration. Target bogs all have a surface growth of Sphagnum; underlying dead Sphagnum ranges from 1 to 6 m thick. Large Sphagnum reserves exist in the Caribou cluster of bogs, and in /979 a bog first identified by infrared sensing was brought into production.

Jan 1, 1984

By Oscar Weiss

An aerial magnetometer survey was carried out by the author's geophysical organization over the Vredefort dome, where Witwatersrand beds are wrapped around a granite plug 25 to 30 miles in diameter. The well- known magnetic shales of the Lower Witwatersrand system (to be referred to as LWW) give strong negative anomalies over the out-cropping portion of the dome. This is unusual as these same shales -cause positive anomalies over large areas near Johannesburg and along a strike of 130 miles between the East Rand and Klerksdorp. It is suggested that the negative polarization is caused by heat and stresses connected with the doming. This negative polarization of sedimentary beds, which usually cause positive anomalies, is a good example of how "magnetic lows" can be caused by "structural highs." Significant magnetic anomalies should be tested by gravity and seismic methods irrespective of the sign of the anomalies.

Jan 1, 1949

By George S. Rice

ARIAL maps of prospective mineral-bearing territory have become almost indispensable in all the branches of exploration, and have proved particularly useful in the great oil area of the Southwest. About nine years ago aerial photographic mapping in this area was begun. The early product was lacking in scale accuracy and other control features, which limited its effective use. Since then, the evolution of the technique of such mapping has been steady, with several mapping companies collaborating with five of the leading oil companies, and aerial maps have been prepared covering practically the entire area.Improvements in cameras, film, and developing equipment and practice have resulted in more uniform and clearer photographs, but the outstanding development has been the accuracy obtained with respect to scale and all other control features. Maps are no

Jan 1, 1936

By R. H. Swallow, George Hess

Aerial photography was once a crude, uncertain tool. Today it is a precision mapping instrument which saves important time and money for strip mining and other industry. Aerial photography began in the boxkite days of aviation. The Army first used it for rough reconnaissance photographs. Then, in the early Twenties, industry began to use aerial photographs of their plants and facilities for advertising or annual reports. The quality of these pictures was not very good by today's standards, but this work began the development of better cameras, better lenses, better photographic techniques.

Jan 1, 1949

By Gerard Matthes

WITHIN the last three years, aerial mapping has made wonderful progress. Its three sources of development in North America may be enumerated as follows: (1) The work of the U. S. Army Air. Service and Corps of Engineers at the McCook Experimental Field, Dayton, Ohio. This is generally regarded as the backbone of this class of endeavor in the United States. (2) In Canada, a great deal has been accomplished in a practical way by methods that have not even been tried out in the United States. Under the leadership of the late Doctor Deville, the Dominion Land Surveyors have turned out reconnaissance maps of large areas at very, small cost. (3) Private capital has contributed a great deal toward development of aerial mapping in a practical way in the United States. Prominent in this regard stands the Fairchild Aerial Surveys, Inc. which has spent large sums in research and development work, especially in the construction of aerial cameras. Its camera is, at present, the official camera of the U. S. Army and Navy Air Services, also, of the Canadian and Brazilian governments. Aerial photographic surveying is a flexible process and adapted to a variety of uses. To date, it has proved. of direct practical value for engineering projects such as reservoir and power transmission surveys, railroad location, drainage, harbor front studies; also, for many commercial purposes, tax assessment, city planning, forest surveys, and lawsuits. In a few instances, aerial photographs have been used successfully by geologists as base maps on which to record field observations, thereby dispensing with pacing and compass surveys. There is reason to believe that, eventually, the aerial map will find wide application in the work of geologists. The reason for advancing this opinion is that aerial maps have, in other fields, proved more complete as regards detail than maps made by standard processes of surveying and drafting, and often are more accurate than the latter. At the present time, five distinct uses are being made of aerial photographs: There is the "oblique" photograph taken at an angle with the horizon; it is used extensively for illustrations in newspapers, magazines, and advertisements. Also, for reconnaissance purposes, it has been found of great practical value. For illustrating reports of engineers and geologists, it offers many obvious advantages. In the Canadian Surveys, maps have been compiled from oblique photographs.

Jan 3, 1925