Search Documents

By P. Leo

Al-Mg-Si alloys are widely used as medium-strength structural materials; extrusion is the most common processing route. In the present hot deformation investigation of a 6060 alloy, the microstructure of the alloy has been analyzed in the as-cast state, after homogenization heat treatment and after hot deformation by tensile tests in the range 400-490°C and 10-4 to 10-2s-1 on both as cast and homogenized alloys. After deformation the microstructure of the as-cast alloy exhibited cavitation. The flow curves at the lowest test temperature T show a gradual softening after a stress peak, being more evident for the alloy deformed in the homogenized state in association with a high yield stress; at higher T a plateau is attained which is lower as T rises and strain rates decrease. For each fixed T, the ductility decreases as strain rate increases for the homogenized alloy whereas, for the as cast alloy, it rises with strain rate. Constitutive analysis gives Q = 240kJ1mol for the homogenized alloy in agreement with published values; this indicates a more rapid strength decline with rising T than Al, suitable for good hot workability along with the lack of cavitation.

Jan 1, 2011

By P. Bacher, L. Dubourg, M. Jahazi, G. Dezaise

Effect of friction stir welding parameters and natural ageing on weld properties are reported. Using a Taguchi design of experiment, attempt is made to systematically examine the influences of the welding speed, tool rotation speed, forge force, tilt angle and pitch ratio on the weld size and ultimate tensile strength of FSWed joints. One millimetre thick plates of AA7075-T6 were welded in lap joint configuration. Samples were characterized by optical microscopy, hardness and tensile measurements. Trends suggested by the results and directions for further investigation are discussed.

Jan 1, 2006

By I. M. Richardson, M. Janssen, I. J. Bennett, V. A. Popovich

The most critical processing step during the manufacture of screen-printed crystalline solar cells is firing aluminium and silver contacts, which generates residual stresses and solar cell bowing. In this paper, an alternative Ag contact formation mechanism is proposed and aspects related to electrical contact properties, residual stresses and layer delamination are investigated. It is found that there are two main processing parameters affecting the uniformity and delamination of the Ag/Si interface, namely the peak firing temperature and the silicon surface roughness. Silicon surface polishing gives a better wetting of the silicon surface by the glass layer, resulting in a good contact and lower incidence of large voids, compared to the case of highly textured surfaces. The non-uniformity in the glass layer and large voids at the Ag/Si interface (in the case of a textured surface) are expected to have a negative effect on the mechanical strength of the solar cell.

Jan 1, 2015

By Z. Zhang, M. -Y. Liu, X. -G. Chen, F. Breton

"The microstructures of AlSi10Mg foundry alloy in permanent mould (PM) and high pressure vacuum die (HPVD) castings were analyzed and compared. The as-cast microstructures of two castings mainly consisted of eutectic silicon particles, primary Mg2Si and Fe-rich intermetallic phases. The surface layer in HPVD castings, which has a unique feature and different structures, was carefully characterized. The dimension variation of microstructural phases along the cross section in PM samples is less than that in HPVD samples, although the size of microstructural phases in PM samples was much larger than that in HPVD samples. The mechanical properties of PM and HPVD samples were evaluated on as-cast and T6-treated conditions. The tensile properties of HPVD castings are remarkable better than those of PM castings on the as-cast condition. The T6 heat treatment greatly improves the tensile strength of PM castings while it has limited impact on the tensile strength of HPVD castings.INTRODUCTION The AlSi10Mg alloys are widely applied to the high pressure die casting (HPD) and high pressure vacuum die casting (HPVD). In the HPD process, the melt is injected into the die cavity under a high speed (30–50 m/s in the gate velocity for aluminum alloys), and solidified under a high pressure (up to 200 MPa in the cavity) and with a high cooling rate (up to ~103 Ks–1) (Gourlay, Laukli & Dahle, 2007; Ji, Wang, Watson & Fan, 2013). This results in a unique microstructure feature that is different to other casting processes under gravity. One major concern in HPD castings is porosity due to trapped air in the cavity (Ji et al., 2013), which seriously restricts the application of a heat treatment on the improvement of mechanical prosperities because of the formation of blisters on casting surfaces. For the process improvement, the high pressure vacuum die casting was developed in 1980s (Uchida, 2009). In this process, the melt is injected into the die cavity under reduced pressure (vacuum), which greatly reduces gas porosity in castings due to effectively avoiding the trapped air. Consequently, HPVD castings are heat-treatable without the formation of blisters on castings surface during heat treatment. The HPVD process has been widely applied to produce high quality structural castings in recent years attributed to reliable vacuum system development (Uchida, 2009). However, the microstructure features of HPVD castings are not systemically characterized yet."

Jan 1, 2018

By R. G. S. Mussi

An inclined cooling plate is utilized as a modification in the compocasting process of magnesium alloy and the mechanical properties of the composites obtained are studied in this work. Based on crystal separation theory, molten AZ91D is poured onto an inclined plate in order to produce solidification nuclei inside the fluid metal, and is mechanically stirred while reinforcement is added. Particulate SiC was utilized as reinforcement in quantities varying from 0 to 15%vol. Dispersion of the reinforcement was observed by macro and microstructure analysis. SiC was properly mixed into matrix until 15%vol., and Vickers hardness tests were carried out for the composites produced. Results obtained for hardness were shown to increase with reinforcement addition and comparable to those of traditional compocasting. Utilization of Inclined Cooling Plate produced good inclusion and homogenization of SiC through an AZ91D matrix, at lower temperatures and shorter times than traditional compocasting.

Jan 1, 2006

By Sangjian Zhang, Zhu Xiao, Lairong Xiao, Rushi Chen, Mei Fang, Zhou Li

The copper-graphite metal matrix composites were fabricated by two different production methods: directly sintering with copper and graphite (Cu-Gr composite), and in-situ sintering with cuprous copper and graphite (Cu2O-Gr composite). During the in-situ reaction sintering, a redox reaction occurs at the interface of the Cu2O particles and Gr particles, resulting in the improved physical and mechanical properties of Cu2O-Gr composites. Compared with Cu-Gr composite, Cu2O-Gr composite has a higher compression strength at any given graphite content due to the improved interface bonding and uniformly distributed fine graphite particles in the matrix. Increasing graphite content decreases the mechanical properties of the copper-graphite composites. The compression strength of Cu2O-Gr composite is 50-100 MPa higher than that of Cu-Gr composite. INTRODUCTION Copper-graphite composites have been widely used in industry due to their low density, relatively high strength and hardness, good thermal and electrical conductivity, arc ablation resistance and self- lubrication ability (Grandin & Wiklund, 2018; Han & Xu, 1999; Huang et al., 2017). Electric sliding contact friction pair in the high-speed railway system and motor brush in electric contact components have a very high demand on electrical conductivity and self-lubrication ability of materials. The electric devices need to bear both mechanical load and high electric current. Copper-graphite composites with good mechanical, electric and self-lubrication properties are the best candidates for application in multifunctional electric sliding contact frication components. The relative sliding speed of friction pair is developing towards 100 m/s or even faster, which can withstand the electric flow of more than 800 A, and it is often accompanied with vibration and impact (Guo & Ding, 2008). Conventional wear-resistant materials can no longer meet the current requirements and this promotes the development of copper- graphite composites with excellent comprehensive properties (Ding, Chen, Zhu, Zhang, & Zhou, 2009; Yasar, Canakci, & Arslan, 2007). There are many ways to fabricate copper-graphite composites, mainly including powder metallurgy method, liquid immersion infiltration method, rapid sintering method and electrodeposition method (Kalin & Poljanec, 2018; Kim, Lee, & Han, 2014; Liu et al., 2018; Wang et al., 2018). Each method has its own advantages and disadvantages, and the powder metallurgy method is the most commonly used one due to its simple process, high economic benefit, and industrial production applicability. The common steps of the powder metallurgy method are as follows (Samal, Parihar, & Chaira, 2013): firstly mixing the copper (copper alloy) powders and graphite with a certain ratio, following by die-forming, and then sintering at the high temperature with or without pressure. The advantage of copper-graphite composites is that the graphite distributed in the copper matrix uniformly and it can form a carbon diaphragm preventing the wear of the composite (Fu & He, 2010). However, the bonding strength of the interface between the copper matrix and the graphite is relative low as the combination between them is mechanical interlocking but not metallurgical bonding (Ma et al., 2008). It is meaningful to develop new fabrication technology of copper-graphite composites with better interface bonding, which could provide guidance for the design of copper-graphite composites with excellent comprehensive properties.

Jan 1, 2019

By S. Xu

Magnesium alloy AM50 is of interest to automotive cradle application because of it excellent castability and good ductility. In this work, microstructure and mechanical properties of both low pressure die cast (LPDC) and high pressure die cast (HPDC) AM50 test bars are characterized. Microstructure was examined using optical microscope, scanning electron microscope (SEM) and transmission electron microscope (TEM). Phase identifications were performed using energy dispersive x-ray spectrometer (EDS) and TEM diffraction. It has been found that LPDC produces much coarser microstructure than HPDC. At the same time, the HPDC samples are more heterogeneous in microstructure and composition close to grain boundaries. Particles with various dimensions and morphologies of two different intermetallic phases, Mg17A112 and A18Mn5, were found in all the samples. Mechanical tests were performed under conditions similar to those related to an engine cradle application. LPDC samples show lower strength but better creep resistance than HPDC mainly due to the difference in grain sizes and grain boundary microstructure between LPDC and HPDC. Creep curves are well described by the empirical Andrade equation. Tensile-compressive yield and creep asymmetries were found in AM50, i.e. better deformation resistance in tension than in compression. The average yield asymmetry ratio for all the samples is 0.87. Microstructural examinations on the samples tested in tension, compression and creep showed that the deformation mechanisms in AM50 were slip plus twining at temperatures up to 125°C. The examinations indicate the important role of twining in the asymmetry phenomenon. The creep results indicate that dynamic precipitation of the Mg17A112 phase during testing is not the mechanism directly responsible for the creep asymmetry in AM50.

Jan 1, 2004

By M. Fairman

The effect of welding speed on the microstructure of friction stir processed (FSPed) AZ31B-H24 magnesium alloy was studied using light microscopy, image analysis, and microhardness tests. The grain size of the magnesium alloy was observed to increase after FSP from about 3.5 µm in the base alloy to about 8 µm in the stir zone. The aspect ratio decreased from 1.60 to 1.55 towards the center of the stir zone. The changes in the grain size and shape caused the microhardness of the samples to drop significantly across the FSPed region from 75 HV in the base alloy to below 55 HV in the stir zone. Decreasing the welding speed increased the grain size due to a greater input of heat energy. The faster heating rate due to the lower welding speed caused a deeper penetration of the annealing effects of FSP. It was also observed that the annealing effects caused by FSP were less pronounced with increasing distance from the interface between the sample and pin tool shoulder. The Hall-Petch type relationship of the micro-indentation hardness as a function of the grain size was observed to hold true after FSP.

Jan 1, 2007

By V. Schwinn, P. Fluess, N. Cauderlier, J. Bauer

From a strategic and economic point of view, the development of fine grain high strength steels for long distance pipelines is intensified world wide to satisfy the demand for natural gas in the future.The project related property profiles based on strength, toughness, crack arrest and sometimes resistance against HIC at defined design temperatures require an effective structural refinement using advanced steelmaking and processing in the rolling mill. The microstructure of modern line pipe steels ranges from ferritic pearlitic to ferritic-bainitic and structures where bainite is the dominant component, possibly upgraded by secondary phases. This paper illustrates microstructures and properties of recent orders on line pipe steels both for onshore and offshore application using different processing routes in the plate mill. Examples will be given for SAWL 485 offshore grades, X65 HIC and X70 HIC onshore grades, respectively. Finally, production results of a recent X80 order will be presented.

Jan 1, 2005

By Sandeep Singh Sandhu, Karanvir Singh Ghuman, Manjit Singh

"Cobalt based super alloy stellite 6 was weld cladded on AISI 304 L stainless steel using SMAW process in order to improve the wear resistance for tyre crusher blades. Microstructure characterization and micro hardness testing was performed on stellite 6 cladding. The suitable parameters viz. 80 Amp current with arc weaving technique was selected by performing bead on plate experiment were further used for depositing multipass multilayer cladding to achieve full filler chemistry at the top surface. Further GTAW process was used for re-melting the top surface of the cladding. Comparative evaluation of the claddings showed that TIG re-melting resulted in increased microhardness and wear resistance in comparison to as cladded specimens even with lesser deposition of material. It was observed that TIG re-melting improved the hardness from 603 HV0.5 kg to 712 HV0.5 kg. Micro structures of stellite 6 contained cobalt solid solution matrix along with inter dendrite chromium carbides which resulted in the increased micro hardness values. Pin on disc abrasion tests were carried out at room temperature and the worn out surfaces were characterized using SEM and EDS.INTRODUCTIONThe crusher blades are used in many industries for crushing various types of material and its wider applications in tyre rubber crushing mills, metal-powder crushers industries etc. Most of the crusher blades are damaged by the wear and impact loading conditions. It is because of metal to metal abrasion and the temperature also plays a vital role in blunting the cutting edges of these blades. The wear is the major cause which leads to loss of material and thus the productivity that can never be recovered (Kotechi et al., 1992). The wear can be reduced by coating of various super alloys which could reduce the behavior of metal degradation even in aggressive environments. Cladding of cheaper low alloyed material with expensive superalloys to enhance the performance of components at low cost has been investigated by many scholars (Deng et al., 2010, Kennametal, 2007, Lolla et al., 2014, Singhet al., 2014, J.N et al., 2003, Ramkumar et al., 2012). Many researchers have reported that cladding is an application of build-up deposits of specialized alloys to resist abrasion, high temperature corrosion and impact loadings. Cladding is used for providing required mechanical strength properties as well as inhibition of oxidation and other corrosive degradation. Coatings are used to protect the heat affected areas like tubes of fluidized bed combustor etc. (Kirchbner et al., 2008, Wang et al., 1994, Hocking et al., 1993, Ananthapadmanabhan et al., 1991, Staia et al., 2001). Coating techniques are widely used for the protection of turbine engine and boiler tubes against high temperature corrosion attack, power generation equipment, chemical process equipment, aircraft engines, pulp and paper processing equipment, bridges, rollers and concrete reinforcements, orthopedics and dental, land-based and marine turbines, ships. Coatings of stellite 6 are widely used in steam turbine blades and boiler tubes for power generation because of an excellent combination of impact, wear and other properties. It can maintain its properties even at high temperature and in harsh environments (Kobayashiet al., 1999, Alam et al., 2009, Munehru et al., 2009). The loading and unloading conditions experienced by the material may induce the surface cracks which lead to its breakage and leaving large pits in the surface (Meng et al., 1995). Many researchers have reported that the properties of cladded layers can be increased by various techniques such as controlling the current variations, dilution, heat input, laser and other re-melting processes, addition of special alloying elements, speed of weldingetc(C.M Anaet al., 2002, Kumaret al., 1999, Luo et al., 2012, et al., Madadi et al., 2011, Shin et al., 2003, Kuzucu et al., 1997, Sudha et al., 2008, Sawant et al., 2017, Houdkova et al., 2016, Ciubo"

Jan 1, 2017

By S. Yue, P. Vo, M. Jahazi

The flow behaviour and microstructure development of a near-alpha titanium alloy during beta working has been investigated. Typical cogging conditions were simulated through compression testing of IMI834 at temperatures of 1025°C-1100°C, strain rates of 0.01 s-1 - 1 s-1 and post-deformation heat treatments up to 4h. Using a synthesis of available literature models, a finite element model has been developed and validated through quantitative measures of flow stress-strain data and beta grain characteristics. Flow behaviour was analyzed through a self-consistent method while the microstructure development was considered with regard to the kinetics of beta recrystallization. Deformation at beta or high alpha/beta working temperatures (T>l025°C) produced minor flow softening with complete grain refinement achieved through metadynamic recrystallization.

Jan 1, 2006

By G. Avramovic-Cingara, H. J. McQueen

The microstructure of commercially pure aluminum was investigated by using polarized optical microscopy (POM), orientation imaging microscopy (OIM), and transmission electron microscopy (TEM) techniques. Specimens were deformed in torsion at 400°C and equivalent strain rate of 0.1 s-1, to various strains of 0.2, 0.5, 1, 4, and 6. The results indicate that POM can usefully reveal grain and subgrain structures over a large field in aluminum. TEM is most suitable to study dislocation substructure and evolution of subgrains. While TEM microscopy and OIM are capable of resolving individual subgrains, OIM can not reliably distinguish subgrains with small misorientations, particularly in samples with low strain. On the other hand, the OIM technique is very useful in the analysis of many regions surrounded by high, medium, and low angle boundaries (HAB, MAB, LAB). Various misorientation maps were studied using different data processing methods. The analysis revealed that the subgrain size is relatively insensitive to strain. The fraction of low LAB ( < 5°) decreased and HAB (>15°) increased conversely with increasing strain, whereas MAB (5-15°) remained stable. The development of an increasingly bimodal grain boundary misorientation distribution is consistent with the predominance of dynamic recovery (DRV) in the evolution of microstructure, combined with geometrical dynamic recrystallization (gDRX), now called grain-refining DRV.

Jan 1, 2006

By Timothy W. Skszek, Adrian S. Sabau, Hebi Yin, Xiaoping Niu

The microstructure evolution during solution treatment plays an important role in mechanical properties of heat-treated aluminum alloys. In this paper, models were reviewed that can predict the microstructure evolution during the solutionizing process of the aging heat treatment of aluminum alloys. The dissolution ofMg2Si particles has been modeled as a diffusion process of Mg in the a-Al matrix. The evolution of volumetric fraction of fragmented silicon as a function of time and temperature was also considered. The growth and coarsening of silicon particles during the heat treatment was considered. It was found that constitutive equations and required property data for most of the phenomena that need to be considered are available. Several model parameters that need to be obtained from material characterization were identified. Pending the availability of these model parameters, this comprehensive model can be used to describe the microstructure evolution of aluminum alloys in order to optimize the solutionizing heat treatment for energy savings.

Jan 1, 2013

By Yongyong Gong, Qijie Zhai, Zhichen Zhang, Qixin Li, Zhishuai Xu

"Microstructure of semisolid slurry of Al-4.5wt.%Cu alloy was investigated with pulse magnetooscillation (PMO) treatment, the results showed that the PMO treatment can refine the crystal structures of Al-4.5wt.%Cu alloy significantly. The discharging frequency of PMO had a great effect on the solidified structure transformation of semisolid slurry of Al-4.5wt. %Cu alloy, and the primary a-Al particles become much finer and rounder with an increase of discharging frequency. However, over a certain discharging frequency, the grains of primary a-Al become coarse.IntroductionOver the last decade, a lot of attentions have been paid on metal rheoforming process [1-4], since it has higher mechanical properties of formed components, strength to weight ratio and age hardenablity. Nevertheless, semi-solid forming is always performed at high solid fractions (40%-60%), so it has the limitation of viscosity, a tends to be difficult to pour semisolid slurry into the hole of the shot sleeve. Therefore, a series of novel semi-solid slurry preparation methods and rheoforming techniques have been invented, such as, semisolid vibration treatment [5], rheocasting [6], pulsed magnetic field process [7], annulus electromagnetic stirring [8], via ultrasonic vibration process [9], equal channel angular extrusion (ECAE) process [l0] and straininduced melt activation (SIMA) process [11].The electromagnetic field is characterized by its effective grain refinement, green, convenient manipulation and without contamination of melt. The mechanisms of dendrite was fragmentation by electromagnetic field have also been largely proposed [12-14]. The broken dendrite arms then undergo a coarsening process to provide the globular structures and obtain much finer and rounder a-Al particles. When compared with other external electromagnetic techniques, Pulse Magneto-Oscillation (PMO) has obtained more fuvors, owing to narrower pulse width and much lower energy consumption. Furthermore, the PMO treatment can reach finer grains with shorter time treatment [16, 17]. This work aims to study the effects of different discharging frequency ofPMO treatment on the microstructure transition of the semisolid slurry of Al-4.5 wt.%Cu alloy."

Jan 1, 2014

By Kathie Mcgregor, Muhamad Firdaus, Nathan A. S. Webster, Yvonne Durandet, W. John Rankin, M. Akbar Rhamdhani

There is a growing interest in recycling/recovery of rare earth elements from permanent magnets. A number of processing techniques are currently being developed but are highly sensitive to the oxidation state of the material. The oxidation microstructure of NdFeB magnets is studied at high temperatures (773-1173 K) to understand oxide formation mechanisms and support the development of viable recycling strategies.

Mar 1, 2017

By Kan Song, Lin Liu, Hengzhi Fu, Jun Zhang, Haijun Su, Xiaojiao Jia

"Al2O3/YAG/ZrO2 eutectic in situ composite has been regarded as new generation of high temperature structural material due to its excellent performance even close to its melting point. The directionally solidified Al2O3/YAG/ZrO2 eutectic ceramics are prepared by recently developed Laser Floating Zone Melting (LFZM) apparatus in which a splitter mirror is used to obtain two beams with the same quality from one CO2 laser. With the two laser beams irradiate the sample from opposite directions, the sample is zone melted. The apparatus configuration and the solidification processing are described in detail. The solid/liquid interface morphology is studied and the mechanism of microstructure formation especially the characteristic of eutectic cellular is discussed. It is shown that YAG and ZrO2 phases play a leading role during the ternary eutectic growth. Meanwhile, the relationship between the solidification microstructure and the processing parameters are investigated.IntroductionAl2O3/YAG/ZrO2 ternary eutectic in situ composite, due to its excellent high temperature mechanical properties, is now considered to be a promising candidate material as a replacement of nickel based super alloy for new generation aero space engine turbine blade [1]. They exhibit flexural strength of 360-500 MPa from room temperature to 2073K in air atmosphere [2]. The compression creep strength at 1873K is 433MPa with the strain rate of 104/s [3]. However, because of the high melting point and complex physical properties, there remain still many difficulties for its application. One of the bottlenecks is the poor understanding of the relationship between microstructure and solidification conditions."

Jan 1, 2012

By Abdelmalek Bouazza, Aamir Mahawish, Will P. Gates

Bio-grouting by means of microbial induced calcite (calcium carbonate) precipitation (MICP) to improve mechanical properties of granular soils has gained much attention in recent years. The biogrouting process offers an alternative and environmentally friendly approach to conventional soil improvement techniques, such as cement. Bio-grouting by urea hydrolysis has been extensively applied to tackle various geotechnical problems. However, it has yet to be applied to improve engineering properties (compressive strength) of a coarse cohesionless material with the aim using it as sand/stone columns within soft and very soft soils. This paper investigates the effect of using light, moderate and heavy biochemical treatments on the unconfined compressive strength (UCS) of coarse sand columns. In addition, the microstructure of the bio-cemented coarse material has been analysed by X-ray computed tomography (XRCT). The experimental results revealed that the UCS could reach up to 200kPa, 1000kPa and 5500kPa for light, moderate and heavy bio-cemented coarse sand columns, respectively. The microstructure investigations showed that the deposited calcium carbonate can be identified using XRCT imaging and can be associated with the gain in UCS values. Various microstructure properties, such as void ratio, dry density and porosity were also identified and compared with the laboratory data.

Jan 1, 1900

By Henry Rawdon

THE METHOD of demonstrating the structure existing in a metal or alloy at high temperatures, by etching a polished sample after it has been heated to the desired temperature, is quite familiar to metallographists. The usual procedure1,2 is to heat the specimen, previously polished for microscopic examination, to the desired temperature, in a neutral atmosphere (hydrogen or nitrogen), then admit the etching gas. (chlorine, hydrochloric acid or similar gas) for. a few seconds, and finally, after flushing out the etching gas with the neutral one, cool the specimen in the neutral atmosphere. The pattern produced by etching at a definite temperature is usually taken as a record of the microstructure prevailing at that temperature. It has frequently been pointed out that changes in composition of the surface metal occur during the preliminary heating in the neutral atmosphere, so that the appearance produced&apos; by the etching at high temperature may not exactly represent the condition of the interior of the specimen. To overcome this uncertainty, the heating has sometimes been done in vacuo,3 the etching gas being ad-mitted when the desired temperature was reached, then pumped out and the specimen cooled in vacuo.

Jan 2, 1920

E. E. THUM,* Salt Lake City, Utah (written discussion?).-While the present paper is confined exclusively to the microstructure of fusion welds, it may be of interest to draw attention to certain appearances existing in resistance welds such as spot or butt-welded joints produced by the Thomson process. For instance, a butt weld between two pieces of carbon tool steel (carbon about 0.90 per cent.) will show concentric ellipsoids of the various materials from pearlite to martensite. The surfaces of demarcation are quite well defined, the center of the ellipsoid being at the intersection of the axis of the piece and the plane of the weld. Often these unannealed welds show a troostitic center; evidently this core was not quenched as rapidly as the surrounding shell. Such specimens are beautiful samples for instruction purposes. An annealed butt weld of this kind will show a very well defined central ellipsoid of decarburized, materials. It is interesting to consider the reason why this change takes place. It must be understood that the heat is on the metal for a very short time, possibly 30 sec. It is therefore evident that the decarburization, or migration, of the carbon takes place with extreme rapidity. Since no blowholes are evident in a well-made butt weld, the deoxidizing air and the products of combustion must migrate with the highest speed; second, the carbon might migrate back into the stock; or, last, a large proportion of the pearlite may be extruded with the hot metal, which forms a fin at the plane of weld. Examining these possibilities in detail, it is not probable that such deep-seated decarburization, extending with maximum effect to the very center of a 2-in. round bar, is done by reaction with the oxygen of the air. This would postulate entrance of oxygen and egress of carbon oxides in large quantity without leaving behind traces in the form of oxides or

Jan 5, 1919

GEORGE F. COMSTOCK (author&apos;s reply to discussion*).-Mr. Thum&apos;s description of the effects of butt welding and spot welding on the micro-structure of steel are interesting and timely. The speed with which the changes noted by Mr. Thum must take place is indeed remarkable, but the writer has noted a similar very rapid diffusion of carbide in annealing a t a rather high temperature certain samples of soft sheet steel containing massive cementite segregated on a small scale. The massive cementite in such steel can be dissolved and distributed very quickly if the proper temperature is attained. Mr. Thum&apos;s explanation of the structure he found in the spot welds seems entirely reasonable, but the mystery of the decarburized material in the butt weld is one that might well be the subject of further research. The possibility of decarburization by air ,might perhaps be worthy of a little more consideration than he gives it, for the oxides formed would be gaseous on account of the presence of carbon, and hence not visible in the microscope, and the effect of the pressure might be to squeeze the carbon oxides, which would normally form blow-holes, out of the metal or possibly into such small volumes as not to be noticed The removal of carbon by liquation and squeezing into the fin would be an effect similar to the "bleeding" of a steel ingot that is rolled while the center is still liquid, giving a soft low-carbon interior in the finished section while the segregate was removed in cropping the pipe. This effect in Mr. Thum&apos;s butt welds could, however, only be obtained if the weld was heated to near the melting point of the steel, and if the carbon was considerably segregated in the bars at the start, for the first effect of the high temperature would be to promote diffusion rather than the contrary segregation and Equation. It is gratifying to learn from Dr. Ruder&apos;s remarks that his researches have resulted in no disagreement with the few points brought out by the writer&apos;s experiments. In addition to the three forms in which nitrogen may occur in iron that he mentions, it would seem that a fourth form is often found; This is apparently a eutectoid, like pearlite, and sometimes almost as coarse as the massive cementite seen in soft steel sheets that have been annealed for a long time. One of the things needed in the metallographic study of steel is an etching reagent that will distinguish definitely between nitride in this form and the more common pearlite or cementite.

Jan 6, 1919