Search Documents

By Tim M. Benson, Adam L. Lamanna, Carolina Martinez-Gutierrez, Mark J. Stephani

The Lower Concourse C Extension (LCE) 108-in Storm Sewer consists of a 2,797-foot long, 27 to 55-foot deep, 108-in I.D. storm sewer tunnel. Situated beneath active taxiways and a terminal apron at Hare International Airport (D), the tunnel diverts ows from existing storm sewers located within the footprint of a future satellite concourse. The project was delivered via Construction Manager at Risk (CMAR) as part of Chicago Department of Aviation’s (CDA) ongoing O’Hare 21 Capital Program. This paper presents project details, multiple stakeholder coordination, subsurface risks and challenges, TBM performance, and impacts to existing infrastructure.

Jun 23, 2024

By Abhishek Asthana

The incineration of Municipal Solid Wastes (MSW) is an attractive process for reducing the volume of the wastes and recovering their energetic value, which, however, requires to be strictly controlled in order to limit its impact on the environment. In this context, we have undertaken the mathematical modeling of the different sections of a typical incineration plant. The combustion of the waste bed, usually carried out on a moving grate, is at the core of the process. This paper presents the 2-dimensional, steady-state model that we have developed for simulating the MSW combustion. The model describes gas flow through the porous waste particle bed, the gas-solid reactions, conductive and radiative heat transfers, drying of the feed, its pyrolysis and the emission of volatile species, combustion of the pyrolysis gases, the formation of char and its gasification by water vapor and carbon dioxide, and the consequent reduction of the bed volume. Pyrolysis kinetics distinguish between cellulosic and non-cellulosic materials and are experimentally derived from our laboratory measurements. The calculated results give a deep insight into the various involved phenomena, an example being the complete consumption of oxygen in a large zone of the bed and the related appearance of a char gasification zone. The influence of various operating parameters, like the temperature and flow rate of primary air, is presented and explained. Finally, the effect of stirring the waste bed on the moving grate is also analyzed.

Jan 1, 2006

By E. Pribonic

Failure of a mine material hoist can cause injuries, fatalities and significant infrastructure damage, along with an associated loss of production. Principal causes of hoist accidents are overwind and underwind. Past and present means of arresting hoisting equipment are marginally effective and utilize destructive systems that are not reusable following an arrest. The use of permanent magnet eddy current arrestor technology is proposed; the history and fundamental science of the technology are presented, followed by real world examples and calculations of performance for failsafe, friction-free, instantly reusable eddy current arrestors as applied to stopping a 30-ton ore skip traveling at 16 metres per second. A comparison of existing arrestor types with the eddy current arrestor is included and limitations of the ECA are also discussed.

Jan 1, 2008

By H. Y. Sohn, M. Pérez-Tello, P. J. Smith, K. M. Riihilahti

A three-dimensional computer model for the Kennecott-Outokumpu flash converting process for copper matte is presented. The model incorporates the transport of momentum, heat and mass, and reaction kinetics between the gas and particles in a particle-laden turbulent gas jet. The k-E model is used to describe gas-phase turbulence in an Eulerian framework. The particlephase is treated from a Lagrangian viewpoint which is coupled to the gas phase through the source terms in the Eulerian gas-phase governing equations. Matte particles were represented as Cu2S·yFeSx. Based on experimental observation, the oxidation products were assumed to be Cu2O, CuO, Fe3O4, and SO2. A reaction mechanism involving the external mass transfer of oxygen to the particle surface and diffusion of the oxygen through the oxide layers of CuzO/Fe304 and CuO/Fe3O4 is proposed. Predictions of the mathematical model were compared with the experimental data collected in a large laboratory furnace. A reasonable agreement between the model predictions and the measurements was obtained in terms of fractional conversion of the oxidation reactions and of sulfur remaining in the reacted particles. The simulation of an industrial flash converting furnace was also performed. Higher oxidation rates, more even distribution of particles, and thus a more efficient use of the reactor volume are predicted with a burner having a distributor cone, than with a single-entry burner.

Jan 1, 1999

By G. K. Ruhlandt, C. W. Kim

"A 3-D Finite Element Method program called ""SOLCAST"" has been developed to simulate the casting solidification process. Using the temperature recovery method to evaluate the latent heat of fusion and applying a new combination of the time integration scheme, SOLCAST reduces the computational time significantly compared to an existing commercial FEM program, and produces accurate results comparable to experimental casting results. Prediction of casting shrinkage porosity for A390 aluminum alloy will also be discussed. To make this FEM program useful for foundry engineers, this program was connected to a commercial pre- and post-processor.IntroductionBecause of recently increased competition, foundrymen must produce high quality castings more economically. Therefore, casting solidification analysis prior to casting production is an attractive way to reduce costs and development time.Although the actual casting solidification process is a very complicated phenomena, foundrymen could predict where shrinkage defects would occur based on a transient conduction heat transfer analysis that includes the liberation of latent heat. A numerical analysis is generally required to solve the heat diffusion equation with the latent heat diffusion term, because casting shapes are very complicated and pure materials are rarely used.Different numerical methods have been applied to the casting solidification analysis 1. Among them, a finite difference method 2 and a finite element method (FEM)3 are most commonly used.Each simulation method has one or more basic difficulties which are different for each method. These difficulties are:(1) Modeling casting shapes on a computer.(2) Time consuming computation.(3) Uncertain material properties."

Jan 1, 1986

By B. I. Hop

The f10wfield set up by the standard Hydro gas purging unit has been predicted by a numerical model. In addition turbulent trajectories of gas bubbles released from the rotor are predicted. Here the deposition rate of inclusions on the bubble surface is allowed to depend on local conditions. Bubbles passing regions with strong pressure gradients, such as close to the rotor, will experience large slip velocities and large deposition rates. This model can deal with any distribution of bubble sizes and inclusions. The results found from the multidimensional flow predictions are discussed in relation to what can be obtained from a much simpler metallurgical engineering approach. The differences between these two approaches to predict the same process will be discussed. The model predictions are compared to experimental results for removal of SiC-particles from aluminium.

Jan 1, 1996

By E. Saez, M. Bellet, T. Coupez, O. Jaouen

"The paper presents a 3D finite element solver for non-steady state fluid flow. The thermomechanical simulation package REM3D® has been initially developed to model Stokes' flow for polymer injection. The mechanical module is based on a Eulerian velocitypressure formulation. The spatial discretization uses P 1+IP1 tetrahedral elements. The front tracking module consists of the resolution of a transport equation, thanks to a space-time discontinuous Galerkin formulation. It includes mesh adaptation, which permits a dynamic refinement at the front, thus controling the numerical diffusion. The same approach is used to solve heat transfer. In this paper, we focus on the specific adaptations done to treat Navier Stokes flow. The treatment of inertia is detailed, as well as the implementation of sliding conditions at mould surface, using conservative normals. Industrial applications are presented.IntroductionThe study of the mould filling stage in casting processes requires the ability to simulate complex non steady-state three-dimensional flows. Most commercial software use the volume of fluid (VOF) method, associated with a Eulerian formulation, see for instance the series of conferences ""Modelling of Casting, Welding and Advanced Solidification Processes"" [1-3]. The VOF method [4] consists in solving the conservation equation dF / dt = 0 for a variable F - the volumic fraction of fluid - whose value is 1 in filled regions and 0 elsewhere. Two fluids are actually considered: the molten alloy and a gas in the empty regions. This method suffers generally from numerical diffusion in the resolution of the free surface tracking equation, which is of pure advective type. The precision of the computation is then strongly dependent on the mesh density. Since the mesh is fixed (Eulerian formulation) this implies that in case of complex flow the user must have a priori a fairly good idea of the flow characteristics in order to capture properly the critical features of the flow. In addition, the method can hardly handle the discontinuity of the material viscosity at the interface. To prevent this difficulty, the viscosity value is smoothed around the interfuce, adding once again some inaccuracy. Since the value F = ½ is supposed to represent the free surface, it results in a smeared fluid surface. An alternative to the fixed mesh methods are the methods in which the mesh covers the fluid domain only, as proposed by Navti and Lewis [5-6], or Gaston and Bellet [7]. Based on updated Lagrangian schemes, they must be associated with an ALE formulation (arbitrary LagrangianEulerian) in order to reduce the number of full remeshing operations."

Jan 1, 2004

By Pedro Jorge Walburga Keglevich de Buzin

A presença de elementos residuais nas sucatas ferrosas pode influenciar a qualidade do aço produzido na aciaria elétrica. Além disto, o cloro existente nos materiais orgânicos que acompanham as sucatas leva a problemas de ordem ambiental. Por este motivo, o acompanhamento destes contaminantes através de métodos de amostragem de sucata se torna uma tarefa importante na aciaria elétrica. Neste trabalho são apresentados alguns procedimentos de amostragem de sucata, bem como uma análise comparativa de sucatas processadas por moinhos do tipo shredder e sucatas sem processamento. Os resultados mostraram um aumento da densidade e a redução do teor de contaminantes (matéria orgânica, alumínio e aço inox) para a sucata processada por shredder em comparação com a sucata sem processamento. Complementando, é apresentado um perfil da concentração de cloro em diversos materiais orgânicos comumentemente encontrados nas sucatas.

Oct 30, 2017

By K. A. Heasley

The objective of this paper is to back analyze the August 6th, 2007, collapse at the Crandall Canyon Mine in Utah, in order to better understand the geometric and geomechanical factors that contributed to that collapse. In this work, the LaModel boundary-element program, along with the best available information, is used for the back analysis. To initiate the analysis, a six-step base model of the mining in the Main West area was developed. This base model included a step for each of the critical stages in the mining of this area. Next, calibrated values for the critical input parameters, rock mass stiffness, gob stiffness and coal strength, were developed and optimized based on the best available information. Finally, the model was used to simulate the final mining scenario. As a result of this back analysis, a number of conclusions can be made concerning the mine design and the August 6th collapse: 1) overall, the area was primed for a massive pillar collapse because of the large area of equal-size pillars, 2) the abutment stress from the active retreat sections and the adjacent longwall panels were significant contributors to the collapse and 3) from the modeling alone, it is not clear exactly what triggered the August collapse, although the active mining is a reasonable assumption.

Jan 1, 2010

By S W. Robertson, A Vercuil, P Craven

Mintek is currently developing a design approach for the heap leaching of low-grade primary copper sulphide material. Since the leaching of chalcopyrite requires elevated temperatures, the generation and management of heat within the heap is crucial. Furthermore, the precipitation of iron needs to be managed to prevent premature blinding of the heap, and acid consumption needs to be limited to contain cost and limit the dissolution of gangue impurities. Standard column tests using jacketed 1-m and/or 6-m columns do not allow accurate prediction of temperature changes and heat generation in an actual heap. Mintek therefore utilizes a computer model to calculate the energy balance and heat generation with time, based on the measured sulphide oxidation rates in the column. The temperature in the column is then adjusted to reflect the computer-predicted temperature in an actual heap. Using this approach, an overall copper extraction of 70% was achieved in 120 days, using 1-metre columns, when treating an ore blend containing 1.36% chalcopyrite, 0.23% chalcocite, 0.07% covellite, 3.8% pyrite and silicate gangue (92%). The chalcopyrite contribution to the total copper content in the feed was 75%. This was followed by 6-m columns using a similar approach, and the column results will be validated on a 23,000 tonne test heap. Key Words: heap; bioleach; chalcopyrite

Jan 1, 2005

Banks' focus in using cash flow methods can differ markedly from that of equity investors. This paper attempts to explain and describe bankers' approach by: ò outlining the fundamental difference between banks' and investors' risk / return profiles. ò describing lenders' consequent use of cash flow methods in mineral valuation. areas. explaining lenders' specific treatment of key risk Fundamental to understanding banks' appraisal of mineral projects is the appreciation that lenders have a basically different risk profile and outlook from those familiar to equity investors. Lenders do not normally participate in any project upside. The economics of lending dictate that banks can only accommodate a low probability of loan default and consequently banks' principal focus in mineral ""valuation"" is ensuring an acceptably comfortable probability of debt repayment. A simple conceptual explanation of lenders' risk / return position is outlined.

Jan 1, 1994

By W. A. Sweet

THE furnace I am now about to describe was designed to obtain and maintain very high temperature. Knowing the cost of the gas furnace that was in successful operation here and abroad, I approached the subject with some misgivings as to my ability to attain anything like success, or even to reach a point of advancement. There seemed to be a field for a furnace of moderate cost for small mills, or where a particular heat was wanted, but the work was not enough to warrant the outlay necessary to build any gas furnace yet brought before the public. The section, Plate V, represents the furnace as I now build it for

Jan 1, 1875

By Etsuro Shibata

The saturated solubility of chromium oxide and the valence of chromium in the slag are important matters when considering how to effectively utilize chromium-containing slags. The experimental data of various types of slags cited in the literature were arranged according to the optical basicity in order to evaluate the effects of the oxygen potential and the slag composition. The saturated solubility of chromium oxide and the Cr2+/ Cr3+ ratio tend to decrease with the increase of the optical basicity of the slag at an oxygen potential below 10.5 atm. However, at an oxygen potential of 0.21 atm, the saturated solubility and the Cr6+/Cr3+ ratio tend to increase with an increase of the optical basicity. A practical approach was suggested to reduce chromium in the stainless steel slag and simultaneously recover it as a ferroalloy by the direct smelting reduction of chromium oxide in the molten slag using some reductant in a small furnace.

Jan 1, 2003

By L. Uotinen, M. Rinne, R. Mishra

Underground mining gives rise to geotechnical hazards. A formal geotechnical risk assessment can help to forecast and mitigate these hazards. Frequentist probability methods can be used when the hazard does not have many variables and a lot of data is available. However, often there is not enough data for probability distributions, such as in the case of new projects. The risk assessment is often subjective and qualitative, based on expert judgement. The purpose of this research is to present the use of Bayesian networks (BNs) as an alternative to existing risk assessment methods in underground mines by combining expert knowledge with data as it becomes available. Roof fall frequency forecasting using parameter learning is demonstrated with 1141 sets of roof fall data across 12 coal mines in the USA. The prediction is nearly identical for individual mines, but when multiple mines are evaluated it is difficult to find a single best fit distribution for annual roof fall frequency. The BN approach with TNormal distribution was twice as likely to fit the observed data compared to the Poisson distribution assumed in the past. A hybrid approach using BN combining multiple probability distribution curves from historical data to predict annual roof fall is proposed. The BN models can account for variability for multiple parameters without increasing the complexity of the calculation. BNs can work with varying amounts of data, which makes them a good tool for real-time risk assessment in mines.

Jun 1, 2021

By M. Y. Levesque

The Australian Government?s Energy Efficiency Opportunities (EEO) program launched in 2006 obliges companies that use more than 0.5 PJ (petajoule) or roughly 139 GWh (gigawatt hour) per year to conduct an energy assessment in order to identify measures to improve energy efficiency. The opportunities identified by the mining sector were assembled in the Mining Significant Opportunities Register that permitted companies not yet embracing and adopting an energy management program to see what those who are, were doing and how much energy was saved, and helps disseminate best practice. The measures can be filtered by company, year, category or equipment type. The creation of a central repository of energy efficiency initiatives is valuable but this existing database could be improved; fields identifying the energy and carbon emission savings associated with a given initiative are a surprising omission. Consequently it does not permit the relative effectiveness of different measures for energy and carbon reductions to be readily assessed. A review of energy management efforts implemented in the mining industry, published in peer reviewed journals, corporate sustainability reports or industry publications during the last 40 years has revealed many examples of best practice. However, the lack of a standardized reporting framework in any of these sources has made it difficult to assess the effectiveness and compare the adopted energy management measures ? just as is the case with the Australian register. In an attempt to address these issues, an improved database structure has been created for energy management measures from the mining industry which identifies energy and financial savings arising from energy management initiatives, classifies applications to specific processes or equipment, and recognizes leaders in the mining industry with respect to energy management. The structure of the register includes the key data relevant to energy management in mining that is absent in the Australian version. The mining industry energy management database has been made available in the public domain where stakeholders can examine the best practice examples. Mining energy champions may also contribute to the register by providing case studies; a standardized entry template affords a quality assurance dimension that is absent in other reporting initiatives. Adoption of this database with its standardized reporting mechanism will enhance transparency of the mining industry in energy matters and help it maintain its social license to operate.

Aug 1, 2013

By B. G. Kelley

The MIDREX® Direct Reduction Process was developed during the 1960s by the Midland-Ross Corporation, which had pioneered shaft furnace technology and stoichiometric gas reforming for use in processing minerals. In 1969, the first MIDREX® Direct Reduction Plant was built in Portland, OR. Since then, 49 additional modules have been sold in 18 countries. For the last ten years, over 60 percent of the world's direct reduced iron has been produced in MIDREX Plants. During the quarter century since commercialization, many technical improvements have been made, including larger shaft furnaces, in-situ reforming, greater heat recovery, improved catalysts, and hot briquetting. Midrex continues to enhance the technology in the areas of economy-of-scale, energy efficiency, alternate fuels, and raw material flexibility.

Jan 1, 1998

By Russ Darr

New methods and techniques in the field of hydrogeology are being developed constantly. One of these advances has been brought about through the use of inexpensive microcomputers. The formulas used in this paper and developed by Theis, Jacob, Glover, Keck, and Dupuit are not new. The methods by which these formulas can be solved are now available to all who wish to get faster, less expensive, and more reliable answers. These methods involve the solution of standard groundwater formulas using microcomputers. Examples and case histories of these methods are presented

Jan 1, 1980

By Theophilus Mensah, Kwame Awuah-Offei

Engineers face significant challenges when determining what geometry provides the most profitable and safe stope for extraction. Several techniques and optimization algorithms have been developed in recent years, but most fail to find optimal solutions because they are heuristic or LP-based without efficient geometric constraints. This paper presents a two-dimensional binary linear programming (BLP) model for determining the optimal combination of blocks in a stope that maximizes the economic value of the layout of stopes for a sublevel deposit. The work draws from Queyranne and Wolsey’s (2017 & 2018) formulations of tight constraints for bounded up/down times in production planning problems to formulate novel and efficient geometric constraints along with geotechnical and grade constraints for the BLP stope layout optimization problem. Results from the model indicate that it is possible to formulate efficient shape constraints in LP-based approaches. The model used for the numerical example contained 144 valuable blocks out of 774 blocks, which translates into an economic value of $53.21M. The BLP model selected 60 valuable blocks and 13 waste blocks that met all constraints translating into a maximum economic value of $34.4M in 1.83 hours within a gap tolerance of 0.00%.

Jun 25, 2023

By J. E. Wey

Extraction of cobalt from cobalt sulfide and cobaltite flotation concentrate from the Blackbird Mine, Idaho, was investigated using an adapted strain of Thiobacillus ferrooxidans. Cobalt extractions as high as 100% were realized in the inoculated experiments, whereas only 4% extraction was obtained in the sterile run. The influence of pulp density on the rate and extent of cobalt extraction was also determined. It was found that the extraction of cobalt followed predominantly the indirect mode of bacterial activity. In this process, ferric iron oxidizes cobaltite to cobalt sulfate and ferric arsenate while being reduced to its ferrous state; the bacteria continuously re-oxidize ferrous to ferric iron. Electrochemical measurements using cyclic voltammetry suggested that cobaltite oxidation involved a number of intermediate reactions.

Jan 1, 1993

By COREY C. BRAYTON

OUR first air travel began at Barranquilla on a trip to the platinum dredging-operations at Andagoya. The fare is based on a minimum weight of passenger, and I will have to admit that the minimum is too low. To make this trip by boat would have necessitated going back to the Canal, thence down to Buena Ventura, and up the San Juan river, which would have taken, counting delays, two or three weeks. The time by Scadta airplane was six hours. We stopped at Cartagena for a day to look over that historic city. The route from there lay along the north coast to the mouth of the Atrato river, then up this river, over the jungle, and over a divide some 300'ft. in elevation and down the San Juan river a few miles to Andagoya at the junction of the Condoto. The General

Jan 1, 1930