Search Documents

By C. M. Loeb, A. M. Gaudin, J. H. Brown

THE object of most size reduction operations in the mineral industry is to liberate the grains of valuable minerals in the ore from those of the gangue. This is usually accomplished by crushing and grinding the entire mass of ore until there is only a small probability that any single particle contains more than one mineral. During this size reduction only limited control exists over size or composition of the particles exposed to the breaking action, and there is no control over the paths followed by cracks generated during the operation. This lack of control usually results in overgrinding and in production of large quantities of very fine material. The first detriment, overgrinding, is costly in itself, but when combined with the second factor it is doubly so. Not only is the fracture of a free particle unnecessary—the fracture of these particles may also make subsequent separation operations difficult, inefficient, and wasteful. It has been pointed out' that if the object of size reduction is to liberate the valuable mineral component of the ore then, ideally, fracture should follow intergranular paths to the exclusion of trans-granular ones. This would result in liberation of the valuable minerals with as little size reduction as possible. This ideal comminution operation is referred to as intergranular comminution, and it was the object of the investigation to determine the extent to which it could be developed by heat treatments. There are many indications in the literature that heating rocks prior to crushing may be favorable. Reports by Holman,2 Yates3 and Myers' are pertinent. These investigators showed that heating certain rocks prior to crushing them did, in fact, improve their crushing characteristics in that fewer fines were produced, although the fact that intergranular comminution was being effected apparently was overlooked. In addition, Sosman noted that if there is appreciable anisotropism in the thermal coefficients of expansion of even a pure mineral, then considerable permanent separation of the grains of the rock can be expected as a result of heating the rock to a high temperature.' By the same token, if there are ap- preciable differences in the thermal expansion coefficients of the various minerals of a multi-component rock, similar results should be obtained by heating this rock. This has been tested, partially, by Brenner," who obtained patents covering the heat treatment of some pegmatitic rocks in order to facilitate comminution of these materials. It has also been demonstrated that this may occur in taconite." Also, the possibility of causing decomposition of one mineral in a rock as a means of promoting intergranular fracture has been considered. Seigle2 and Schiffman et al. have obtained patents on such processes as applied to calcareous iron ores. These reports all indicate that heat treatments prior to crushing may contribute materially to intergranular comminution, but they also indicate that no organized attempt has been made to determine the controlling factors of the method or to determine its applicability in general. The present article is a report on the initial phase of such an investigation. The authors have reviewed the claims of prior investigators and have attempted, also, to establish the factors that might determine the applicability of heat treatments in the mineral industry. In this work 2000-g samples of various rocks were heated in a small laboratory furnace and crushing and sizing operations were carried out in standard laboratory equipment. All samples of each rock were as nearly identical as possible in particle size, grain size, and composition and contained only lumps coarse enough to contain many grains each. Tests on Granite A number of tests were made on a coarse grained Finnish granite obtained in the form of coarse chips from a local monument yard. This rock exhibited little variation from piece to piece in either composition or grain size. The minerals contained were quartz, orthoclase, small amounts of hornblende, and minute quantities of mica. Grain size ranged from about 1 mm to about 3 mm. Temperature of the Heat Treatment: In some cases the granite was heated to a particular temperature and crushed, hot, immediately upon withdrawal from the furnace—in others the rock was allowed to cool before crushing, but without quenching to room temperature after heating. In most tests on granite the heating period was about 2 hr with the furnace at the highest temperature for about 1 hr. Cases in which these periods were varied greatly will be presented separately.

Jan 1, 1959

By H. L. Miaw, A. M. Gaudin, D. W. Fuerstenau

A quantitative method for evaluating density of slime coatings has been developed and applied to formation of iron oxide slime coatings on quartz and on corundum. Slime coating density is related to flotation recovery and to properties of the electrical double layer at mineral surfaces. IN spite of considerable study, the nature of slime coatings in flotation is still not completely understood. However, phenomena that control floc-culation and dispersion of colloidal systems are now interpreted in terms of electrical double layers.",' Colloids will flocculate even though the particles carry the same charge, but when two dispersed colloids of opposite charge are mixed. flocculation ensues even more rapidly. Analogous phenomena seem responsible for slime coating on minerals in flotation systems. To shed new light on the issue it was considered desirable to devise a tool that would measure slime coatings. The usual method has been to examine photographs of presumably representative surfaces, after. an intervening washing in running water. But such an examination is non-quantitative, and the changes in chemical environment represented by the washing may have removed the slime coatings that existed during flotation. To provide the possibility for a correlation with electrical double layer phenomena, the experiments were made with quartz, corundum, and iron oxide, for which elec-trokinetic data are available.'-" Since the properties of the electrical double layers of these oxides depend on the pH of the solution, pH will be the most important variable. Furthermore, because the zero point of charge for silica, iron oxide, and alumina occurs at pH 3.7, 8, and 9.5, respectively, the relative charge on the slime and mineral can be changed over wide ranges. Because of its practical importance in quartz flotation, iron oxide powder was chosen as the slime. Also, its uniform composition, contrasting color, and ease of analysis make experimentation simple. In this investigation, correlation was sought between the effect on flotation recovery of slime addition and slime coating density. Materials and Methods Details are available in a thesis by Miaw." The quartz was selected from pure Brazilian crystalline quartz, crushed, sized (65/150 mesh) acid-cleaned, washed, and stored in conductivity water. The corundum (synthetic alumina of high purity prepared by Linde Co., Chicago) was crushed, sized (65/100 mesh) deslimed, boiled in nitric acid, washed, and stored in conductivity water. The iron oxide slime, reagent-grade ferric oxide (—400 mesh) from Allied Chemical & Dye Corp., was heated to 160°C, cooled, and stored in a vacuum desiccator. In the electron microscope the slime particles appeared to be about 0.3µ in size, but their large specific surface (87,900 cm per g, by gas-adsorption method, using krypton) suggests that the actual particles are smaller than 0.3r. Had they been perfect nonporous spheres, they would have had a diameter of 0.13µ.

Jan 1, 1959

By S. R. B. Cooke, H. S. Choi, D. H. Harraway, I. Iwasaki

The mineralogy of natural iron ore samples and their slimes have been investigated and the nature of slime interference in iron ore flotation has been studied. The results have been correlated with the flotation behavior of a natural ore sample. Various conclusions have been reached as a result of these studies. In the flotation of iron oxide ores, desliming is generally considered to be an essential step to successful separation, irrespective of whether the iron oxide or siliceous gangue minerals are to be floated, although some workers have found empirically that certain collectors and reagent combinations are less sensitive to the presence of slime than others. The detrimental effect of slime is considered to be twofold. First, the presence of slime presupposes a high reagent consumption because of high specific surface. When clays are present and when cationic collectors are used abstraction by ionic exchange may augment this condition. Attempts to compensate by the addition of large amounts of reagent result in only partial correction. Second, slime coatings on granular particles tend to interfere with the bubble-mineral contact. The nature of slime coatings in flotation is quite complex and has been the subject of considerable study; an attempt was recently made by Fuerstenau et al.' to relate the slime-coating density with flotation recovery and with the properties of the electrical double layer at the mineral surfaces. Although major constituent minerals in the oxidized iron ores of the Mesabi and Cuyuna ranges are hematite and goethite (limonite) as the iron oxides, and quartz and chert as the siliceous gangue, very little is known of the mineralogy and of the chemical and physical characteristics of the slimes, and still less of the interaction between slimes, collector, and the mineral surfaces. For pragmatic reasons iron ore slimes are defined as — 20p material, based upon the calculated settling velocity of a quartz sphere of the stated diameter, and of all other equal-settling mineral particles. Active slime interference with flotation is usually attributed to particles 5p in size or finer, the extent of such interference appearing to depend not only on the mineralogy but also on the size distribution of each mineral in the slime fraction. The objective of this work was to acquire a more specific knowledge of the constitution of iron ore slimes and of their role in flotation. The mineralogi-cal composition of natural slimes was obtained by differential thernal analysis (hereinafter referred to as DTA), electron microscopy, and chemical and X-ray analyses. Some flotation tests were made on natural ore samples. The surface properties of several constituent minerals were investigated by electrophoretic measurements and by determination of the adsorption of some typical flotation collectors. Finally, simplified flotation tests were made on granular goethite and quartz in the presence of various artifically prepared slimes; the results were compared with laboratory flotation tests made on natural ores. MATERIAL AND METHODS Mineralogy of Some Iron Ore Slimes: Samples of two wash-ore tailing::, hereinafter identified as A* and B, *Sample A of the present investigation 18 the same am ore A in ref. 3. of a wash ore C, and of a paint rock D, all from the Mesabi range, were selected for investigation on the basis of prior information concerning their flotation behavior. The two wash-ore tailings, when deslimed, were known to respond well to flotation, whereas the wash ore was high in goethite, tended to be slimy, and responded poorly to flotation. The paint rock also exhibited sliming tendencies, and was suspected to contain relatively large quantities of clay minerals because of its high A1203 content. Gruner states that the paint rock of the Mesabi frequently contains kaolinite. To ascertain the relative sliming tendencies of each sample a standardized desliming method was employed. All samples were ground through 65 mesh using jaw and rolls crushers. A 500-g sample of each

Jan 1, 1962

By D. H. Gieskieng

Published tables of jaw crusher capacities are compiled for the most part from field performance data, interspersed with interpolations, extrapolations, various safety factors, and other modifications. Such a table attempts to balance and equalize field data from widely Werent materials, with differences of crushability, efficiency of feeding, sizing of the feed, and so on. The tests described in this paper were undertaken with the objectives of checking previously reported capacities; of studying the effects of various factors upon the capacity, including jaw plate curvature; and, if possible, of deriving a general capacity equation. Such an equation has been derived from the data obtained in these tests. It is given together with factors for its use. While more accuracy than is usually required may be obtained by careful application of the equation, it is of simple form and provides a convenient reference plane upon which the potential capacity of various crushers may be compared, and with which operating adjustments may be made on existing installations. The principal deviation in these tests from the usual approach consists of a laboratory technique which has been developed for the production of selected capacity data. Recording instruments are connected to crushers in such a manner that a continuous record is produced which discloses the inherent maximum capacity of the crusher and shows capacity decreases caused by hangups. The capacity effects of various crushing conditions are made more evident by this arrangement. The recording instruments were first applied to a standard sized 10 by 7 in. Blake-type jaw crusher in the laboratory. Suficient tests were run on this with various combinations of setting, throw, speed, feed sizing, shapes of jaw plates, and other operating features, to establish the individual effect of each on the capacity. The instruments later were applied to much larger crushers in the field, through the excellent cooperation of the managements in the Mesabi Iron Range, and data were obtained which closely corroborated the established trends. The capacity equation resulting from the test work is made up of a series of factors, each representing the contributing effects of setting, speed, width of chamber, nip angle, feed density, type of jaw plates, stroke, and the overall operating technique. Fortunately, most of these factors were revealed to be in direct proportion to the capacity for straight plate chambers. This equation is also applicable to chambers using curved plates, with slight modifications resulting from the capacity limitation of the upper portion of the crushing chamber. The equation has been derived from tests covering a very wide range of feed density and hardness. It has been found valid, providing that the feed material is either nonpacking in character, as is usual, or allowance in designing the crushing chamber shape has been made to accommodate this characteristic. Preliminary investigation has shown that the equation is also applicable to single-toggle jaw crushers. Conditions of this are that the top of the flywheel rotate towards the top of the crusher opening, and that the horizontal motion of the swing jaw relative to the stationary jaw at the discharge opening be considered as the stroke. The relatively large upper chamber jaw motion would probably result in realiza-

Jan 1, 1950

By D. H. Gieskieng

THE advent of curved jaw crusher wearing plates made an approach other than segmental layout analysis desirable for prediction of capacities. For some time it had been known that the drawing board capacities of crushers using these plates had to be considerably modified by complicated experience factors to achieve agreement with results. Because these apparent capacities could be readily increased severalfold by minor crushing chamber shape changes, it was necessary that the utmost precaution be taken in predicting capacities of jaw plates modified for nonchoking, special wear characteristics, or any other reason. To this end the laboratory and field tests outlined by the author in a previous paper1 were made on Blake-type jaw crushers. The results of these tests were summarized in a simple first degree equation applicable to crushers using either straight or curved jaw plates. This equation first outlines the maximum capacity potential of a given crusher, then reduces this figure in accordance with installation circumstances by means of a realization factor. It was found subsequently that this equation, with the addition of an eccentric throw factor, is applicable to standard types of single-toggle or overhead eccentric jaw crushers as far as maximum capacity potential is concerned. However, these crushers have realization factor curves somewhat different from those outlined for the Blake type. While this paper is concerned principally with standard type single-toggle crusher capacities, the evaluation of data obtained with these machines is simplified by comparative reduction to the 10 x 7 in. Blake-type equivalents upon which the summary of the preceding paper was made. Convertibility of data from one type of crusher to the other also tends towards confirmation of both. The agreement of these data is sufficient to be considered complimentary. Consequently the feed factors, f, previously reported for Blake crushers are slightly adjusted to an average with the single-toggle crusher results. Blake-type equation: C = f.d.w.y.t.n.a.r [I] Single-toggle type equation: C = f.d.w.y.t.n.a.e.r [21 where C is the capacity in short tons per hour through the crusher, f is a feed factor, dependent upon the presence of fines in the feed, and the surface character of the jaw plates used. Values of f : Smooth Plates Corrugated Plates With normal fines 0.0000414 0.0000319 Fines scalped out 0.0000368 0.0000252 Large pieces only . 0.0000312 0.0000215 d is the apparent density of the broken product in pounds per cubic foot. (If the true specific gravity of the feed is known, 40 pct voids may be assumed and d becomes 37.4 times sp gr). w is the width of crushing chamber in inches. y is the openside setting of the crusher, in inches. In the case of corrugated jaw plates it is measured from the tip of one corrugation to the bottom of the valley opposite. t is the length of jaw stroke in inches at the bottom of the crushing chamber. It is the difference between open and close-side settings. n is rpm, or crushing cycles per minute, a is the nip-angle factor. It is unity for 26" and 3 pct greater for each less nip-angle degree. A nip-angle of 20" has an a value of 1.18, and an angle of 30" has an a value of 0.88, see Fig. 1. r is the realization factor. It is unity for perfectly uniform choke feeding and usually less for actual operating conditions according to the method of feeding used and the probabilities of hang-ups involving the size of feed and crusher opening. Approximate values are given by the curves in Fig. 2. These values are further reduced by intermittent feeding, e is the throw or diameter of gyration of the single-toggle crusher eccentric in inches. As evident in Fig. 1A, variation of feed size will generally have little effect on nip-angle if both jaw plates have flat areas. Jaw plates having continuous curvature, as in Fig. 1B will have different nip-angles, depending upon the size of feed. For test work as described in this paper this effect was accounted. For general compilation of capacities for average feeds it is suggested that the nip-angle be taken at the various settings computed, at an arbitrary level, such as is indicated in Fig. 1C. Data Evaluation To bring the Blake and single-toggle type crusher capacity test results to common terms for evaluation, all data are converted to terms of 10 x 7 in. Blake-type performance at conditions of 100 lb per cu ft, 10 in. chamber width, 250 rpm, 0.65 in. stroke, 3-in. openside setting, and 18° nip-angle. (The nip-angle of the 10x7 in. Blake is 18° at 3-in. setting.) The single-toggle crusher performances are also divided by the eccentric throw to bring this effect to unity. As outlined,' laboratory and field tests made on Blake-type crushers ranging from 10 x 7 in. to 60 x 48 in. were summarized along the foregoing conditions of speed, stroke, etc. This resulted in groups of data which correspond to feeds with fines, feeds

Jan 1, 1952

By C. H. G. Bushell

The author maintains that selectivity in flotation depends in part on differences in rates of flotation. The rate of flotation should be directly proportional to the frequency of particle-bubble collisions. In this paper, it is suggested that floatable particles of the mineral must be distinguished from nonfloatable particles. Success in flotation is entirely a matter of selectivity. All minerals can be made to float. The problem is to make one mineral float and leave the others in the tails. For a typical ore, with all minerals naturally hydro-philic, a collector which is adsorbed by only one mineral and not at all by the others would give perfect separations. The hydrophobic, collector-coated mineral would separate cleanly from the remaining minerals. In practice, no such highly specific reagents are known. All standard collectors adsorb on most minerals to some extent, and selectivity then becomes a matter of extent of adsorption rather than adsorption on some minerals and not on others. Flotation is therefore a compromise process: if enough reagent is used to float all the desired mineral, the concentrate will be low grade; conversely, high grade concentrates can be attained only at low recovery. With many minerals coated with collector to varying degrees, selectivity appears to depend in part on each mineral floating at a different rate. The study of flotation kinetics is therefore a basic requirement to quantitative understanding of the process. REVIEW OF PREVIOUS THEORIES Before a particle enters the froth it must strike a bubble and adhere to it. Flotation rate will therefore depend on the number of particle-bubble collisions

Jan 1, 1962

By L. J. Erck, T. E. Ban

A discussion of laboratory procedures used to determine pellet quality and to simulate handling and firing conditions. Strength-temperature relationships in pelletizing; effect of chemical additives on agglomeration; and crushing, abrasion, and impact resistance of the pelletized products are discussed with respect to five different iron ore concentrates. IN most routine experimental work on products and processes, method:; of operation and product evaluation are established from accurately controlled laboratory tests. With particular emphasis on the pelletization of fine iron ore concentrates, standardized procedures of laboratory production and product testing have been established at Cleveland-Cliffs Iron Co. Research Laboratory at Ishpeming, Mich. A program of this nature was used for investigating the agglomeration characteristics of various iron ore concentrates. The factors which control the process were studied and subsequently controlled for these investigations. Pelletizing as applied to iron ore agglomeration involves the preparation of spheroidal masses from a fine moist concentrate, followed by high-tempera-ture firing to produce a final product. The preparation of moist spherorids is generally designated as balling. This produces the so-called green pellets or balls. After, these have been fired they are called pellets. Balling is accomplished by rolling moist concentrates in a revolving drum until small spheroids form by a snow-balling action. These balls are then heated in a shaft furnace, or a modification of this device, to a temperature high enough to cause agglomeration within the individual balls while they descend countercurrent to hot oxidizing gases. By this process the lour strength balls are converted through various chemical and physical-chemical processes into hard pellets. With correct balling and firing, the pellets are strong, resist abrasive action and handling treatments, and provide a suitable blast furnace and open hearth feed. In 1950 Tigerschiold and Ilmoni developed a working hypothesis to explain the formation and stability of green pellets.' Their work was presented on the basis of geologists' discoveries concerning the soil-water system and C. V. Firth's early postulates of green pellet formation.' Fundamental reactions oc-curing within fired pellets have been described by Cooke and Ban, who showed the microstructure changes caused by different firing temperatures." All these investigators have provided scientific clarifications of agglomeration by the pelletizing process and have opened avenues for greater development. Mineral grain growth and ceramic bond formation are the two basic phenomena imparting coherency to particles within a fired pellet of iron ore. Each of these is established by the transfer of thermal energy to the mineral particles. Grain growth mechanisms are chiefly physical reactions wherein smaller particles consolidate into larger ones, with resulting decrease in surface energy conforming with the second law of thermodynamics. Ceramic bond formation is a chemical reaction usually between basic and acid metallic oxides of the gangue and ore minerals. CaO, MgO, A1203, and FeO of Fe3O4, react in varying proportions with SiO, or Fe2O3, to form a great series of compounds or amorphous solid solutions. These product bond iron mineral particles together by a bridging action or by direct reaction with the surfaces of the particles. The result of the grain growth-ceramic bond formations is a consolidated, coherent compact of gangue and iron minerals formerly held together by much weaker bonds of interstitial water and forces common to dry, unconsolidated particles.4 With respect to iron ore agglomeration, these high temperature bonding reactions have been described by Schwartz, who referred to the bonds in sinters," and by Cooke and Ban, who referred to the bonds in fired pellets." The extent of the bonding phenomena and the consequent strength of fired pellets is governed by

Jan 1, 1954

By W. J. Carlson, I. lwasaki

Manganese and silica in nonmagnetic tailings from the direct reduction-magnetic separation step were so closely associated that no physical concentration methods were effective. Dilute sulfuric acid dissolved manganese and iron rapidly; manganese in the form of silicates was virtually insoluble in sulfuric acid solutions, thereby governing the maximum extraction attained by leaching. Autoclave leaching at elevated temperatures and at high oxygen pressures reduced the iron extraction to less than one tenth without affecting the manganese extraction. There was an indication that autoclaving solubilized the manganese silicates appreciably. Elimination of iron from leach solutions was carried out by aerating the solution in the pH range of 6.5-7; a platinum-calomel electrode pair provided a reliable indicator for the end point of iron removal. The purified leach solutions were free of interfering impurities for the recovery of manganese as metal, dioxide, or carbonate. Manganiferous iron ores of the Cuyuna Range, Minn., are too low in iron content to be directly useful as iron ores, and too low in manganese content to be termed manganese ores. Common methods of physical beneficiation such as gravity concentration and flotation have not been successful in upgrading this material. The R-N process, when applied to manganiferous iron ores,1'2 produces sponge iron by direct reduction of iron oxides, while leaving manganese as manganous oxide. From fine grinding and magnetic separation of the reduced ore, a tailing is produced which is relatively rich in manganese and low in iron content. The nonmagnetic tailing can readily be leached with acids and then further processed to recover manganese in various forms. In this way, two processes, neither of which would be an economic solution to the Cuyuna ore problem by itself, may be combined to produce two marketable products, thereby rendering the over-all process economically more attractive. This article reports on the results of a leaching study on the nonmagnetic tailings, both in a batch agitation vessel and in an autoclave; on the problems involved in the purification of leach liquors by aeration; and on the recovery techniques used to produce manganese metal by electrolysis, manganese dioxide either by electrolysis or by autoclaving, and

Jan 1, 1968

By E. O. Wagner, V. F. Parry, W. S. Landers

Development work has shown that the yield of primary tar from coal is proportional to the heat in the volatile matter of the coal and that the yield of tar from noncoking coals may vary from 10 to 45 gal per ton on the ash-free and moisture-free basis. Pilot plant operations have proved that 100 to 135 pct of the bench-scale carbonization-assay yield of tar can be obtained. FOLLOWING investigations by the Denver Bureau of Mines on drying fine coal in the entrained state,'. ' Texas Power & Light Co. employed the fluidized technique to upgrade Texas lignite for use in power plants. Because of the rapidly rising cost of natural gas in Texas the company agreed to cooperate with the Bureau of Mines in studying further the upgrading of lignite by low-temperature carbonization, since potential value of the tar would help offset the cost of fuel. Considerable interest was aroused, therefore, when Aluminum Co. of America decided to use dried lignite in its 240,000-kw power plant at Rockdale, Texas, operated by Texas Power & Light. Carbonization of coal before burning in a power plant is not new. Plants in Germany have been operated for many years on carbonized brown coal and lignite briquets produced in large integrated plants. Large-scale experiments in carbonizing pulverized coal with hot flue gases were made 30 years ago at Milwaukee," and many inventors have proposed other processes. In the U. S., technical and economic problems have prevented successful operation of large plants on carbonized coal. but new techniques of handling solids in fluidized beds may overcome these difficulties, particularly if the higher volatile noncoking coals are used. Any bituminous material will decompose when heated to about 900°F to yield primary tar, gas, and char. The quantity of tar obtained from various coals depends on their rank and volatile content and to some extent on rate and method of heating. The liquid products derived from thermal decomposition of peat, brown coal. lignites, oil shale, and noncoking bituminous coals can be easily liberated by rapidly heating these materials in a fluidized bed at about 500°C (932°F). Since it takes only a few minutes to heat small particles of fuel to carbonizing temperature in a fluidized bed, processing plants can be built to handle up to 50 tph at relatively low cost. The pioneering development work being conducted at Rockdale, Texas, by Alcoa and Texas Power & Light will solve many engineering problems of such operations. The Bureau of Mines at Denver has studied the carbonizing properties of several hundred coals by small scale assay at 500°C, deriving a simple correlation between the potential yield of tar and the proximate analysis. This correlation, shown in Fig. 1, compares the heat in the volatile matter of the coal with the potential yield of primary tar. The yield of primary tar varies from 12 to 50 gal per ton of pure coal." About the same amount of heat is needed to * MAF equals moisture-and-ash-free basis. distil any dry coal at 500°C, and the time required to carbonize a given particle size is about the same for any coal. It is therefore obvious that coals rich in volatile matter will show the greatest profits when processed. Texas lignites are rich in volatile matter, which contributes some 5700 Btu per lb of MAF coal, and the potential primary tar and oil yield from this lignite averages 12 pct by weight or 27 gal per ton from the pure lignite. Texas lignites are considerably richer in potential tar than lignites of North Dakota and Montana. During 1950 the Bureau of Mines conducted many experiments on carbonizing fine dry coal in the entrained state, publishing a report4 n major features of pilot and commercial-size units required to carry out the process. Additional experimental work has been done at Denver and the pilot plant has been improved, particularly the facilities for studying removal of fine dusts from tar vapors and gases at high temperatures by electrostatic precipitation. A number of materials have been carbonized, including sawdust, peat, brown coal, Brazilian oil shale, lignites, and the lower rank bituminous coals having noncoking properties. Straight coking coals cannot

Jan 1, 1957

By G. A. Vissac, R. G. Minet, N. E. Sylvander

R. G. Minet—The authors' description of the remarkable progress made in the last few years in applying the fluidized solids technique to the problem of lignite drying and carbonization clearly demonstrates that engineering techniques available today may make many processes practical and profitable which a few years ago were considered otherwise. As pointed out in the article, the future of the carbonization step hinges on the value and utilization of low temperature tar. On paper, at any rate, this tar looks like a valuable raw material for the chemical industry to use. Some 50 to 60 pct may be converted to pitch for electrodes, roofing, road tars, and other valuable products; the 25 to 30 pct tar acids could conceivably form a basis for a new low cost resin or plastic of the phenolformalde-hyde type. Yet these materials are so new and dissimilar from available sources that much work must be undertaken by the chemical industry before they will be accepted. Now that the work of Dr. Perry and his colleagues has made a large supply of low temperature tar a real possibility, I would expect the chemical industry to accelerate its work in this field. On the basis of certain data available in the literature it appears possible to produce a more aromatic tar, although in smaller yield, by operating at temperatures in the range of 1300" to 1500°F. Operating a fluidized bed process for lignite at these conditions should be technically possible, at least, and could produce a tar having more familiar characteristics. I wonder if Dr. Parry would care to comment on such a possibility. Incidentally, in our own work on carbonizing coking coals in fluidized beds, using Ohio, Pennsylvania, and West Virginia high volatile bituminous coals, we have obtained yields which agree with the correlation given for tar yields vs moisture and ash-free volatile Btu. Our data are slightly under the line, but certainly in the range of the correlation. We have also obtained evidence in support of the authors' statement as to the effect of air on the process. In our pilot plant all the heat required for carbonizing is released by internal combustion of char in the fluidized bed in normal operation. We are also equipped to obtain all carbonization heat by external electric heaters on the shell of the carbonizer while introducing only an inert gas to the process. We note no difference in tar yield or characteristics between the two operations. In the case of the gas, however, it appears that some hydrogen is consumed by the air combustion. We would be interested in hearing in a little more detail about the hot dust and char handling problems at Sandow. Have the authors found char subject to spontaneous combustion? Have they ever tried a coking coal in their pilot plant? V. F. Parry (author's reply)—Production of a more aromatic tar by operation of the carbonizer at 1300" to 1500°F does not appear to be economical. 1) The capacity of a reactor operating at 1500°F would be 30 to 50 pct less than the capacity at 932 °F and the cost of processing would increase materially. 2) The cracking of tar vapors in a reactor requires appreciable time to complete the reactions and it is doubtful that considering the very short time of residence of tar vapors within the reactor (4 to 10 sec after evolution) the basic character of the tar would be changed significantly. This is indicated from the data reported in Table XIV. 3) General studies have shown that it is advisable to operate at the minimum temperature to produce the maximum tar and minimum gas. 4) Operating problems and the maintenance of vessels and reactors, and the hazards of handling hot char, increase with the temperature of carbonization. It is technically possible to operate at temperatures as high as 1500°F, but in my opinion it is not economical or desirable. We believe that the primary tar must be won in the simplest way and then processed alone to change its character for production of desired products. It is interesting to have confirmation of our observations on the reaction of air with the products of carbonization. The major reaction is with the char, fol-

Jan 1, 1957

By S. J. McCarroll

Fig. 1—The belt shown at right carries filter cake to mixing station over calciner. Crude ore conveyors appear in right background. THE Three Kids mine, some six miles east of Henderson, Nev., is in a typical southwest desert area, with high dry summer heat and cool to cold winter seasons. The manganese deposit was located during World War I.' During this period 15,000 to 20,000 tons of ore assaying up to 41 pct manganese were shipped. Interest in the deposit was not revived until the middle thirties, when experiments on the ore were initiated. Test work indicated possible recovery of only 70 pct by flotation, but in 1941 additional work was done at the Boulder City pilot plant of the U. S. Bureau of Mines and also by M. A. Hanna Co. As a result, the Manganese Ore Co. was formed and a plant utilizing the SO2 process was constructed. Numerous operation difficulties ensued, and the plant. was closed when the manganese situation in the country eased. In 1949 Hewitt S. West initiated negotiations to acquire the plant. In 1951 Manganese, Inc., was formed and contract entered into with the General Services Administration to supply 27 million units of metallurgical grade manganese in the form of nodules to the national stockpile. A second contract was made to upgrade 285,000 tons of stockpile ore. Test work was undertaken by the Southwestern Engineering Co. and likewise by the Boulder City pilot plant at the U. S. Bureau of Mines. Results obtained indicated the commercial feasibility of the flotation process. Construction of the plant, which is shown in Figs. 1 and 2, was started in June 1951, and operations on a break-in basis began in September 1952. Apart from the usual starting difficulties two major disasters caused serious setbacks, one a kiln failure in February 1953, and the other a fire that destroyed the flotation building in June of the same year. The nodulizing section of the plant resumed operation in November, and the flotation section in January 1954. The ore minerals are chiefly wad,* with minor amounts of psilomelane, and occur in sedimentary beds of volcanic tuff. The ore is overlain with beds of gypsum which outcrop or may be covered with surface gravel. Intermediate beds of red and white tuff occur frequently with lenses of red and green jasper and stringers of gypsum and calcite. Small amounts of iron are present; lead content averages about 1.0 pct and minute amounts of copper and zinc are found. Barite, celestite, and bentonite are present. Since these are made up of minute asicular crystals, moisture content is very high, averaging about 18 pct. Ore reserves have been estimated at 3 million tons averaging 18 pct Mn2 and up to 5 million tons after grade is dropped to 10 pct Mn. A good part of the orebody was stripped of overburden by the previous operating company . Approximately 50 pct of the ore, representing more than 60 pct of the manganese, can be mined by open-cut methods. A system for underground min- . ing has not yet been decided on. Open-cut mining with benches of 20 ft has proved satisfactory. Although the ore is soft and appears dry and dusty it has a certain resilience, probably due to the porosity and moisture which makes drilling and fragmentation difficult. Wagon drills have been abandoned in favor of the Joy 225-A rotary drill which will put down a 43/4 -in. hole at the rate of 2 ft per min. Holes are spaced in a pattern with 8 to 9-ft centers. Forty percent powder has been used, but better breaking to 2-ft size is obtained with low velocity bag powder of 30 pct strength. Loading is done with one 21/2-yd shovel, and cleanup follows with one D-7 bulldozer. The ore is hauled with Euclid trucks about 1000 ft from the pit to a blending pile, where the daily mine production is spread in layers by bulldozing until approximately one month's mill feed is accumulated. A new pile is then started and mill feed is drawn from the first pile by one 13/4-yd shovel and Euclid trucks, with a haul of approximately 500 ft. Mining is performed by an independent contractor with engineering and supervision by the company staff. Early test work indicated that the manganese could be floated with soap, a wetting agent, and fuel oil to give a recovery of better than 75 pct with a grade of 43 pct Mn. The concentrate when nodulized with coke would upgrade to 46 pct Mn or over, and the lead volatilized to 0.6 pct residual.

Jan 1, 1955

By J. W. Peirce

Advances in instrumentation now make it possible to measure accurately flaw of such difficult-to-mea-sure liquids as mining slurries. A mass flowmeter, which introduces no restrictions in the line, will measure the mass flow of slurry equal to the volume flow times the mms/unit volume. In the mass flowmeter system a volume flow measurement is electrically multiplied by a density measurement in order to give mass flow. Fig. 1 shows a typical mass flow measuring system. The volume flow is measured by a magnetic flowmeter and the density is measured by a gamma gauge cell, neither of which have any restrictions in the line. Consequently, there is no clogging and no more loss of head than there would be in a similm length of standard pipe. None of the parts extend into the flowing stream and there are no moving parts in the measuring elements. PRINCIPLE OF OPERATION OF THE VOLUME FLOW TRANSMITTER The magnetic flowmeter, which is used for the volume measurement, operates on the principle of a generator (Fig. 2). This principle states that when a moving conductor cuts lines of force in a magnetic field, a voltage is induced in it. Moreover, if the dimensions of the conductor remain constant, then the induced voltage is directly proportional to the velocity of the conductor. Since the voltage is strictly a function of flow velocity, the transmitter output can in no way be influenced by such factors as temperature, viscosity, turbulence, or conductivity. The linear output is detected by flush mounted electrodes (as shown) and transmitted to a potentiometer flow receiver. Magnetic Meter Construction: The metering tube is constructed of nonmagnetic stainless steel. (See Fig. 3.) To prevent shortcircuiting of the generated voltage, the tubes are lined with a suitable liner, depending upon the corrosive, erosive or other properties of the liquid or slurry to be measured. A uniform magnetic field is produced by two saddle-shaped coils of insulated copper wire. A laminated iron core focuses the magnetic field at a 90' angle to the flowing liquid. The voltage generated by a flow of liquid through the magnetic field is detected by two point electrodes mounted flush with the inner wall of the metering tube, 180' apart. Electrodes are made of Type-316 stainless steel or other material suitable to the application . Volume Flowmeter Operation: The millivolt output of the metering transmitter is transmitted to a potentiometer-type receiver (Fig. 4). The self-balancing, self-standardizing receiver has a drive unit for circuit rebalancing. The measurement change imposes an unbalanced input on the twin windings of the drive unit. The resulting unequal pull on a segmental rotor provides the motion which drives a pen, while simultaneously and steplessly repositioning a rebalancing element. Changes in conductivity have no effect on the accuracy of the measurement or the calibration of the instrument. The minimum conductivity values are determined by the length of the transmission cable and the size of the transmitter. They can be as low as five micro mhos, since there is such a small load on the electrodes. Because the meter electrically averages all of the incremental velocities in an irregular flow profile, it is ideally suited for turbulent flow and suspended solids. Straight runs of pipe are therefore not required. The transmitter can be installed close to

Jan 1, 1962

By A. M. Gaudin, J. H. Brown

In a survey of the effects of heat treatment on the comminution of various rocks, it was found that unusual size distributions often characterize the broken products, and that this is related to a great increase in intergranular fracture1. It is the purpose of the present paper to contribute to an understanding of this effect. In a thesis by one of use, critical consideration was given to many mechanisms which could conceivably be responsible for the increased intergran-ular fracture. It was shown that neither gross chemical changes nor intergranular corrosion are required. Among non-chemical mechanisms the most likely appeared to be (1) Uneven expansion due to thermal gradients, giving spalling (2) In a manner similar to that prevailing in metals, the appearance at high temperature of intergranular weakness. (3) Unequal thermal expansion of adjacent grains. Experiments were designed and conducted to permit a choice among the many alternative mechanisms and in particular among the three listed here. EXPERIMENTAL MATERIALS Tests were made on the materials listed in Table 1. Of each material, only lumps similar in composition and grain size were used. The three marbles listed in Table 1 were analyzed to assure that their chemical compositions did not differ greatly (Table 2). On the basis of the chemical analyses, of differential thermal analyses, and of X-ray powder diffraction patterns, it appeared that the marbles were very similar except for their grain sizes.

Jan 1, 1961

By D. C. Seidel, M. C. Fuerstenau, R. J. Roman

The existence of a surface charge on the alkali halide salts is shown, and a flotation mechanism involving surface charge and collector solubility is developed. Data suggest that KC1 is positively charged and that NaCl is negatively charged in saturated brines, and that the neutral molecule RNH,Cl is the collector in the amine-KC1 system, RSO, is the collector in the sulfonate-KC1 system, and RCOONa) is the collector in the fatty acid-NaCl system. A number of hypotheses have been advanced to explain the mechanism of soluble salt flotation; one of these involves exchange between collector ions and surface cations. With this mechanism Gaudin1 suggested that the differences in flotability of halite and sylvite with primary amines are due to the ionic size of the RNH;, Kt, and Na t ions. Fuerstenau and Fuerstenau expanded this hypothesis to include many other alkali halide salts. Several exceptions to this hypothesis are known. That is, this model does not explain why salts containing the same cation, or why salts of different degrees of hydration, respond differently to flotation. For example, why NaI is floated with an amine whereas NaI .2H,O is not. Further, no correlation between ionic size and flotation response can be made with sulfonate or car-boxylate as collectors. In addition, this hypothesis does not explain the effect of magnesium or lead activation, nor does it offer any explanation of the role of temperature in salt flotation. Rogers and Schulman3 realized some of the inadequacies of the ion exchange mechanism and proposed another mechanism based on the heat of solution of the salts. They concluded that weakly hydrated salts can be floated with alkyl amines and sulfonates, that strongly hydrated salts can be floated with fatty acids, and that excessively hydrated salts cannot be floated at all. Their work was not limited to the al-

Jan 1, 1969

By J. R. Johanson

With the continuing development of automatic operations, it is important that reliable discharge rates through hoppers and bins be obtained for bulk solids. In most applications a feeder is used to control the feed rate. The selection of this feeder size is usually based on the rated ability of the feeder to move material without regard to the capability of the material to flow through the opening in the hopper onto the feeder. The dis charge rate through a given hopper opening may vary from zero to a theoretical maximum depending on the flow properties of the material. This paper presents an equation for the maximum discharge rate for a bulk material as a function of the hopper shape, the opening size and the flow properties of the material. Discharge-rate tests on various materials indicate good agreement with calculated values for opening sizes from a fraction of an inch to several feet. As part of a program to develop improved design criteria for bulk storage and handling facilities, a specific study of the methods involved in calculating the rate of discharge of bulk solids from hoppers and bins has been made. This study is closely related to earlier work done on the prevention of flow problems through the choice of proper design geometry of hoppers and bins1. The present paper is an extension of this earlier work, and therefore many of the concepts previously derived and explained will be used without explanation. Two types of flow will be considered: plane-strain flow in a wedge-shaped hopper and axial-symmetry flow in a conical hopper. The literature contains many studies on discharge rate for regular-shaped dry particles2*3 such as glass beads, lead shot and coarse dry sand. However, the work is empirical in nature, and it is difficult to extrapolate the given information to apply to moist, sticky materials typical of many industries. Some studies4 have shown a decrease in discharge rate with an increased moisture content of the material. However, no attempt was made to correlate the discharge rate with moisture. The method of calculating discharge rate presented in this paper was derived analytically from the basic knowledge of the flow of frictional, cohesive, granular solids, The equation includes the effect of material cohesion (stickiness), hopper configuration, opening size and bulk density of the material. THEORETICAL WORK The basic assumptions made in deriving the discharge rate equation are as follows: 1) The material is a frictional, cohesive, granular solid. 2) The flow is considered continuous and without significant density change. 3) The material at the hopper opening forms a continuously failing arch that is in dynamic equilibrium. 4) The strength of the material in the arch, which must be overcome for the arch to fail, is caused by the pressure in the flowing mass near the hopper opening. 5) This pressure at the hopper opening can be calculated5. If we consider the dynamic equilibrium of an arch of uniform thickness such as that shown in Fig. 1,

Jan 1, 1965

By S. C. Sun

With the aid of emulsifiers, intense high-frequency sound waves are capable of emulsifying any collector in water. The data show also that ultrasonically emulsified collectors are more effective in floating minerals than the nonemulsified collectors. THE use of ultrasonics in forming emulsions is not new. As early as 1927 Wood and Loomis reported preparation of emulsions with ultrasonics. In 1935 Rschevkin and OstrawskyV escribed the use of great ultrasonic power in producing fine emulsions of various oils and paraffin in water. Recently Oyama and Tanaka3 employed ultra-emulsification to increase the effectiveness of sodium ethyl xanthate in flotation of chalcopyrite and galena. An emulsion is a two-phase system consisting of two incompletely miscible liquids, the one being dispersed as finite droplets In the other. The dispersed liquld is known as the internal or discontinuous phase, and the surrounding liquid is termed the external or continuous phase. There are two types of emulsions; one is oil-in-water (O/W) and the other water-in-oil (W/O). The word oil refers to the liquid other than water. Circumstances exist in which the emulsion type is not clearly defined, and the internal and external phases both contain portions of the opposite phase. This is said to be a dual emulsion. Among the many hypotheses, 5a, B proposed for the formation of emulsions, the Bancroft's adsorbed film or double interfacial tension theory is widely accepted. Bancroft 7, 8 deduced that in the process of emulsification the interfacial tension between oil and water is lowered by the formation of an emulsifying film, which contains the adsorbed molecules and/or ions from the emulsifying agent and the two liquids. This film has two interfacial tensions, one with the water and the other with the oil, which are not necessarily equal. The difference in interfacial tension between the two surfaces of the film is chiefly responsible for forming different types of emulsions. For example, if the interfacial tension between water and film is less than that between oil and film, the film will become convex on the water side, thereby tending to form an oil-in-water emulsion. On the other hand, if the interfacial tension between water and film is greater than that between oil and film, the film will become concave on the water side, thereby tending to make a water-in-oil emulsion. In line with this theory, emulsifying agents soluble in water have the tendency to form oil-in-water emulsions, while those soluble in oil form emulsions of the reverse type. Apparatus and Experimental Procedure: The ultrasonic apparatus shown in Fig. 1 consisted of a hypersonic generator (A), Brush Development Co. model Bu-204; a hypersonic transducer bowl (B) whose resonant frequency is 400 kc per sec; and a round-bottomed glass tube (C) of 2.2 cm ID and 21 cm in length. The acoustical output power of the hypersonic transducer bowl was standardized with a Hewlett Packard vacuum tube voltmeter, model 41 0B, across the hypersonic generator output. The glass tube, containing the materials to be emulsified, was placed 1 cm above the central surface of the transducer bowl, which was filled with water as shown in Fig. 2. Ultrasonic emulsification was performed in three steps, although a one-step method has been used: 1) emulsifying the predetermined amounts of col-

Jan 1, 1956

By R. L. Bleifuss

The object of this study was to evaluate the oxidized taconites of the western Mesabi iron range and to establish a correlation between the various basic taconite types and their concentratability. The initial work included a study of the original mineralogical and stratigraphic facies of the fresh taconite and traced the oxidation and leaching patterns developed during the conversion of this material to oxidized taconite. Subsequent studies have extended this work to include the semitaconites and also the wash and heavy media ore types widely developed in the area. Each basic original mineralogical facies or taconite type produces during alteration an equivalent secondary oxidized facies which has a unique mineralogical composition and texture. These control the concentratability of the oxidized taconites. Actually the influence of the original mineralogical composition of the iron formation extends even further and determines whether the most likely product of oxidation and leaching will be a wash ore or a heavy media ore and even to the direct shipping ores where the ratio of hematite to goethite is largely determined by the original taconite type. The relationship between original taconite, oxidized taconite, semitaconites, and wash and heavy media ores is briefly summarized in Table I. The terms are not precise and in some instances tend to overlap. The table is intended to point out only the essential differences between the various materials. The original taconite was dominantly composed of mixtures of magnetite, iron carbonate, iron silicate, and quartz (chert). In a few thin stratigraphic units, hematite was present as an original constituent. The alteration of the original taconite to oxidized taconite has resulted from the circulation of ground waters through an initial fracture system related to minor structures in the iron formation. The chemical reactions have involved the oxidation and decomposition of original minerals such as magnetite, iron carbonate, and iron silicates to hematite or goethite. The alteration at this early stage is characterized by pseudomorphic replacement of the original minerals by oxidation products although retaining the major textural features of the original taconite. There was very little secondary migration of iron at this stage and the total iron content of the rock has been only slightly increased. Further alteration of this material to form a semi-taconite, a wash or a heavy media ore, involves extensive removal of silica in solution and significant redistribution of iron units. Wash and heavy media ores are developed by the growth of coarse secondary iron layers, dominantly goethite, coupled with the removal of silica in solution and decomposition of the cherty layers. This paper is concerned primarily with the materials classified as oxidized taconites which are characterized by oxidation of the original mineral constituents with little secondary enrichment. The area studied, shown on the index map, Fig. 1, extends some 30 miles along the strike of the Biwabik formation roughly from Hibbing to Coleraine. This study was greatly facilitated by the basic stratigraphic and mineralogical studies of Gruner1 and white2. The bulk of the material in this presentation represents a portion of the author's contribution to a study sponsored by the Great Northern Railway on the oxidized taconites of the western Mesabi.3 METHOD OF APPROACH A total of 106 drill holes, representing some 30,000 ft of drilling, were examined and sampled. The drill holes were logged and some 1500 composite samples were prepared for chemical analysis and bench scale metallurgical tests. These samples were analyzed for total iron and ferrous iron; and magnetite iron was determined by a standard Davis tube test at minus 200 mesh. Standard reduction roast tests using 150-gram samples of minus 10 mesh material were made on these 1500 composite samples with a mixture of H2, CO2, N2, and H2O at a temperature of 650°C. This roasted material was pulverized through 150 mesh and concentrated in the Davis tube. The iron recoveries and concentrate grades obtained on the roasted products were used to assess the concentratability of the oxidized taconites. Detailed mineralogical work was done on thin sec-

Jan 1, 1964

By M. Earl Volin, M. Adnan Goksel

The hydro thermal agglomerating process described (U.S. Pat. No. 3,235,371, 1966)* is different from the cotzventional high-temperature processes. Green pellets or briquettes made with mixtures of moist iron-ore concen- trates and burned or hydrated lime fines are hardened in an azttoclave at 198°C and under steam pressure for 112 to 5 hr, with or without previous drying. Under the neutral conditiotzs, oxidation of magnetite does not occur as in the conventional processes. The resulting azzlomerates-- are hard and resistant to abrasion and weathering, and they do not disintegrate in the Under test. The equipment required for the process is not complicated, and favorable operating costs are projected because of the low temperamre and efficient heat recuperation. A low capital investment makes the process attractive even when the annual pellet production is below a million tons.

Jan 1, 1970

By R. Adair, W. R. Hudspeth, W. T. McDaniel

D. C. Ralston (U. S. Bureau of Mines, Washington, D. C.)—Flake mica can be beneficiated by a wider variety of methods than almost any known mineral. However, most of these methods are not recorded. It is therefore a pleasure to find a written record of another application of a new method of beneficiation. The fact that the Humphries spiral gives a concentrate containing the mica flake mixed with the slime and small grit has forced a further separation by screening, in which the finest of the flake will pass through. Fine flake has its uses and if mixed with slimes or clay is recoverable reliably only by flotation. This loss must be charged against the spiral. On the other hand, the new muscovite mica paper recently brought out by General Electric Co., can be made only with grit free flake larger than 50 mesh. It is of interest to learn from the authors whether the washing of the flake on a 50 mesh screen can take the grit content below 1 pct, to meet this new demand. Must another degritting process be used on the flake, like electrostatic treatment of the dried material? H. D. Snedden (The Humphreys Investment Co., Denver)—When recovering mica in the spiral, gangue particles coarser than 16 mesh can be rejected more readily when operating at a high pulp density (35 pct solids) or a low volume rate (—15 gpm). A launder screen as used by Lehigh Coal Co. has proved very satisfactory to partially dewater the mica concentrate and to reject any gangue slimes it may contain. Under certain conditions mica cleaning in the spiral can be improved by reagentizing the spiral feed, the object being to insure wetting of the gangue minerals and to agglomerate or prevent wetting of the mica particles. R. B. Adair (authors' reply)—The grit content of the mica recovered on Humphreys Spirals varies with the fineness of the launder screen used to clean the mica product. Normal practice has been the use of 80 mesh screen, which will produce a mica product of acceptable grit content for most purposes. By using a 50 mesh screen, and increasing the screen area per ton of feed, it is felt by the authors that a mica of 99 pct plus purity could be obtained. This statement would hold only in the case of mica feed which was well de-laminated, and free from "clay balls," (semikaclinized feldspar), which tends to follow the mica through the process.

Jan 1, 1952

By Jack White

MUFULIRA Copper Mines, Limited, conducted tests on the concentrator in 1942 to determine which type of ball mill, that is, Conical Trunnion overflow or Cylindrical Grate discharge, produced the greater quantity of finished product at the lowest cost. All the data which follows applies to Mufulira ore and to the particular degree of grinding produced with the classifiers installed at Mufulira concentrator. JACK WHITE, Member AIME, is Concentrator Superzntendent, Mufulira Copper Mines, Ltd., Mufulira, Nortltern Rhodesia. Sun Francisco Meeting, February 1949. TP 2729 B. Discussion of this paper (2 copies) may be sent to Transactions AIME before Feb. 28, 1950. Manuscript received Feb. 28, 1949. Test Procedure: The test was carried out using ball mills No. 1 to 9 (conical trunnion overflow) as the standard with which to compare No. 10 (cylindrical grate discharge mill). The conical trunnion overflow ball mills are 10 ft diam by 72 in., and the cylindrical grate discharge mill is a No. 99. Each mill runs in closed circuit with a Dorr type DSFX classifier 8 ft wide by 30 ft long. The feed is considered as being identical to all ten units. The figures for the test were derived as follows. Dry Tons Milled: For No. 10 unit (cylindrical grate discharge mill) this figure was taken from the ball mill weightometer, which was corrected for error, and then for moisture content. The weightorneter was checked twice a week during the test, and the error did not exceed 3 pct at any time. The moisture was obtained from a 24 hr moisture sample taken by the ball mill operator hourly, and placed in a closed bucket. The sample was cut where the conveyor drops the feed into the ball mill chute. The Mill Sampling Department made a daily moisture determination on this sample. To obtain the dry tons on units No. 1 to 9 the No. 10 figure was deducted from the month's dry tons milled figure, which, in turn, was taken from the crusher weightometer tons corrected for weightometer error and moisture. All tons reported in this test are short tons of 2000 lb. Ball Mill Hours: This was taken daily from the Shift Boss reports giving actual running hours for each unit. Screen Analyses: Coarse Heads (Ball Mill Feed): The monthly composite coarse heads screen analysis, done by the Mill Sampling Department, was used for the minus 200 mesh in the feed to the mills. F. X. Classifier Overflow: The ball mill operators took an hourly 24 hr sample of the overflows of units No. 1 to 9. This was a hand sample, but cut with a special cutter, and is believed to be very reliable. On No. 10 unit, an hourly 24 hr sample, and an hourly shift sample were cut in the same way. These five samples were split, filtered, and dried by the Research Department and were then wet screened on a 200 mesh screen. The average of the three shifts samples on No. 10 unit had to check the 24 hr sample within 1.5 pct to be acceptable. A weighted composite was cut each day from both 24 hr samples, and at the end of each month it was screened as follows: Wet screened through 325 mesh, the plus 325 then screened on a rotap for 15 min through 65, 100, 150, 200, and 325. This was done in duplicate. All splitting, drying, and screening of samples was done by one of the Mill Research staff, to insure accuracy. F. X. Classifier Overflow Densities: These were taken from the Shift Boss reports. Densities were taken by the ball mill operator every hour. Circulating Loads: These were taken a number of times during the test both by direct method (weighing a measured portion of classifier rake sand, and deducting moisture) and by calculation using the formula:

Jan 1, 1951