Search Documents

A three?stages countercurrent fluidized bed prototipe reactor to neutralize the SO2from smelter gases has been developed. For gases with 8 vol-%SO2, at 800°C and for 4 h mean reaction time of the limestone, the capture of SO2 is 99%, with off gases with 0.07 vol-%. For 2 vol-%SO2, the total capture of SO2 can be obtained at 750°C and 4 h reaction time. The calcine obtained contain a blend of unreacted limestone and calcium sulphatewith minor amounts of residual lime.

Jan 1, 2006

By M. Illikainen

Limestone is used for neutralization of acid leachates in a number of hydrometallurgical processes. The aim of this study was to clarify how limestone ground to different particle sizes can neutralize sulfuric acid. The laboratory scale ball mill was used in grinding experiments carried out using ball sizes of 20, 30 and 40 mm and volumetric slurry densities of 30, 40 and 50 percents. Varied grinding times were used in order to produce limestone samples with different particle size classes on which the neutralization potential and rate were determined. The results of the study showed that the neutralization potential of limestone is not dependent on its particle size between 5 and 120 µm. However, the particle size strongly affected the neutralization rate of sulfuric acid: The smaller the particle size, the higher the rate of neutralization. Thus, when optimizing the cost efficiency of the process, the optimal degree of grinding should be considered taking in account the required residence time in neutralization phase.

Sep 1, 2012

By A. E. Desrosiers, R. L. Kathren, D. L. Haggard, J. M. Selby

INTRODUCTION The radiological health significance of thorium-230 stems from its tendency to separate from the uranium238 parent, concentrate in bone tissues, and to subsequently irradiate the radiosensitive tissues lining the bone surfaces and the bone marrow. Indeed, thorium-230 may be the radionuclide which contributes the major dose following intake of natural uranium (Hartley and Pasternack 1979). This is reflected by the most recent recommendations of the International Commission on Radiological Protection, which specify the limits shown in Table I for the annual intake of radionuclides by occupationally exposed workers (ICRP 1979). TABLE 1. Occupational Annual Intake Limits (microcuries per year) for Selected Uranium Nuclides and Daughters (ICRP 79) [Radionuclide Ingestion Inhalation] [Uranium-238 200 0.05 Uranium-235 200 0.05 Uranium-234 200 0.03 Thorium-234 300 200 Thorium-230 3 0.02 Radium-226 2 0.5] Clearly, the relatively low annual limit of intake for thorium-230 shows it to be of greater radiological concern than its parent radionuclides. Because of the greater toxicity and different metabolism of thorium-230, monitoring only for uranium-238 does not satisfactorily identify the possible hazard from thorium-230 nor does it provide any real indication of the metabolism or biodynamics of these two radionuclides. Thorium-230 has a half-life of 80,000 years and can be detected by direct counting of the alpha particles or photons emitted during its transformation to radium-226. The 4.69 and 4.62 MeV alpha particles are distinctive and specific indicators of thorium-230 and are emitted with abundances of 76% and 24%, respectively. The principal photon, a 68 keV gamma ray, is emitted in only 0.37% of the transformations and is, therefore, not useful for low level measurements. The other photons emitted have even lower yields, or, in the case of radium L x-rays, are non-specific and, hence, useless for quantification. High sensitivity measurements of thorium-230 currently are usually accomplished by wet washing of the sample substrate, quantitative chemical separation of thorium atoms, and, finally, direct measurement of the alpha particles emitted from a massless deposition. This procedure is complicated, expensive, and time-consuming, and subject to interferences from uranium, other actinides, and other thorium isotopes. Recently, the feasibility of low-level measurement of thorium-230 by neutron activation analysis (NAA) was demonstrated (Kathren, Desrosiers and Church 1980). Two principal variations of the NAA method were used in this study: 1) instrumental NAA technique and 2) post-irradiation radiochemical separations (RCS). Instrumental NAA procedure is a nondestrucive technique which is preferred because of its simplicity. The procedure is as follows: after irradiation with a known neutron fluence, the samples are transferred to a clean container and quantitative gamma spectroscopy performed. With the radiochemical separations procedure, the sample is initially treated as in the instrumental technique. However, after irradiation, a known amount of "carrier" is added to the sample. The element(s) of interest are then separated from the rest of the matrix by distillation, precipitation and extraction techniques. The resulting sample, now free of interferring elements, is then ready for gamma-ray analysis. The use of a "carrier" is to determine the loss of element-of-interest during the chemical separations process. The neutron activation cross section of thorium-230 has an epicadmium resonance value of 1,010 barns (Mughahghab and Garber 1976) and a thermal neutron cross section of 23 barns. The 25.52 hr thorium-231 produced releases two photons of significance: an 84 keV complex, (6.5% yield) and 25.6 keV (15% yield) (Lederer and Shirley 1978). The 84 keV complex is particularly useful for quantification since neither natural uranium, thorium, their daughters, or activation products emit photons in this region. However, the higher yield of the 25.6 keV photon may result in increased sensitivity if there are no other photons of similar energy emitted by other radionuclides in the sample. PRELIMINARY STUDIES Thorium-230 standard stock solution was prepared from a pure sample of the oxide purchased from Oak Ridge National Laboratory. From this stock solution a series of samples were prepared for irradiation in the TRIGA Mark I reactor at Reed College. Various dilutions were prepared as well as thorium-230 spiked urine samples. Irradiation times varied from 1 to 54 minutes in a neutron fluence rate of 1.84 x 1012 n/ cu m-sec. The neutron spectrum was abundant in thermal neutrons, having a Cd ratio of approximately 10. Treated urine samples were also analyzed by the NAA instrumental method. Analysis of untreated urine samples was not possible due to the high background

Jan 1, 1981

By K. V. Godfrey

With the increasing need to exercise better control over mill circuits has come a requirement to develop rapid, accurate means of measuring circuit parameters. One of the most important parameters is the assay of the material in the circuit (or about to be introduced to the circuit). To date, most on-stream analysis has been performed using X-ray fluorescence equipment. Neutron activation offers an alternative method in certain circumstances, and one which has several interesting advantages. Recognizing the need for a simple, safe neutron activation unit suitable for on-stream analysis in the mineral industries, Atomic Energy of Canada Limited has designed, built and tested the SHERLOCK system. One prototype (SHERLOCK I) is located in Ottawa and is now used primarily in research. A second prototype (SHERLOCK III) is located in Vancouver at the laboratories of B.C. Research. This unit is being used for some development research and for evaluating the unit in specific applications. Most of the work completed to date has been aimed at proving the technique and in developing some of the parameters needed to design systems for a milling plant. Funding for the work has been through research grants and through sponsor¬ship by interested companies.

Jan 1, 1971

By J. S. Kirkaldy, W. J. Slater, G. R. Mason

Activation analysis for copper and manganese in 10 mg samples machined from aluminum-base diffusion couples has been used in the study of ternary diffusion in the Al-Cu-Mn system. The accuracy, economy and convenience of the method are considered to be very competitive with other methods for analysis of such small samples. Neutron-activated aluminum-zinc alloys in the range from 10 per cent to 100 per cent zinc have been equilibrated with a known volume and the vapors subsequently condensed and collected. The vapor pressures relative to pure zinc (the thermodynamic activities) have been determined at 550°C' by recording the relative count of /'-rays from zn65 in the collected samples. The method is a sensitive one, although subject to serious obstacles to experimental accuracy.

Jan 1, 1961

By Dalton. J. L., H. P. Dibbs

An account is given of investigations into the application of two neutron methods to the on-line analysis of slurries. One deals with the application of the neutron moisture gauge principle to the determination of the water content of iron oxide slurries, and the other with the application of gamma radiation from thermal-neutron-capture to the determination of the composition of aqueous slurries of iron oxide, copper oxide, zinc oxide and sulphur. Linear relationships were found between the composition of the slurry and the neutron count-rate in the first study, and between the slurry composition and the prompt-gamma-ray count-rate in the second study. A mathematical relationship has also been developed which relates changes in the prompt-gamma-ray counts from hydrogen to changes in slurry composition.

Jan 1, 1973

By E. C. de Beer

"SynopsisA number of important areas in nuclear fuel cycle, at both the front end and back end, offer ideal opportunities for the application of non-destructive evaluation techniques. These techniques do not only provide opportunities for non-invasive testing of e.g. irradiated materials, but also play an important role in the development of new materials in the nuclear sector. The advantage of penetrating radiation used as probe in the investigation and testing of nuclear materials makes X-ray and neutron radiography (2D) and tomography (3D) suitable for various applications in the total nuclear fuel cycle. The unique and different interaction modes of the two radiation probes with materials provide several opportunities. Their complementary nature and non-destructive character makes them most suitable for nuclear material analyses, analytical method development, and the evaluation of the performance of existing nuclear material compositions. This article gives an overview of the X-ray and neutron radiography/tomography applications in the field of nuclear material testing, and highlights a few of the success stories. Several selected areas of application in the nuclear fuel cycle are discussed to illustrate the complementary nature of these techniques as applied to nuclear materials.IntroductionDuring the development of new materials for the nuclear industry, materials testing and characterization are of the outmost importance to maintain safety standards and reliability. No compromise on safety in the workplace in any area within the total nuclear fuel cycle can be tolerated, and therefore most in-situ material characterization and testing is conducted by certified and qualified personnel schooled in destructive and non-destructive testing (DT and NDT) methods. Certification and qualification in NDT can be obtained through many training centres in South Africa in accordance with European, American, and other international standards (SGS, n.d.; SAIW, n.d.; African NTD Centre, n.d.)."

Jan 1, 2015

By K. S. Olson

My reaction when first asked to present this paper was; "What could I possibly say that would hold the audience?s attention for 15 minutes? What could I offer that anyone familiar with the Nevada Barite Industry wouldn't already know?" Well, quite frankly I can't. The industry has certainly been anything but exciting for the past 10 years and, in fact, quite depressing. The challenge, for those few of us left in it, has been to keep it alive. At times it has felt like a doctor must feel with a terminally ill patient. All I can do is recap the past ten years, review the present state of the industry, and offer a few personal opinions and observations as to where I think we are headed.

Jan 1, 1993

By L. Hoffman, F. Seymour, S. Hoerger

Newmont has a large integrated operation in Northern Nevada with numerous mines, stockpiles, and processing facilities. There are over ninety defined metallurgical ore types and over sixty defined gold recovery process options. To take better advantage of the available synergies, a complete Nevada wide mine plan and process model along with a mixed Integer and Linear Programming optimization tool has been developed and implemented. This system is maintained and operated by a Nevada Planning Group. Standard in-house planning software tools and methods have been implemented at all mine sites. While increasing the effectiveness of planning in Nevada, these changes have allowed a significant reduction in overall Mine Engineering staff.

Jan 1, 1999

By S. Hoerger

Newmont has a large integrated operation in Northern Nevada with numerous mines, stockpiles, and processing facilities. There are over ninety defined metallurgical ore types and over sixty defined gold recovery process options. To take better advantage of the available synergies, a complete Nevada wide mine plan and process model along with a mixed Integer and Linear Programming optimization tool has been developed and implemented. This system is maintained and operated by a Nevada Planning Group. Standard in-house planning software tools and methods have been implemented at all mine sites. While increasing the effectiveness of planning in Nevada, these changes have allowed a significant reduction in overall Mine Engineering staff.

Jan 1, 1999

The optimisation and validation of shearer cutting methods is a time consuming engineering task. Many different parameters, of which not all can be controlled, can vary. The easiest solution, to increase the installed power and the longwall length, is not always the best. A different cutting method can increase the capacity without the need of new machines. The Department for Mining and Metallurgy Machinery at RWTH Aachen University therefore developed ProSL, the simulation tool for shearer and longwall operations. ProSL enables the engineer to create his own cutting methods and compare it with other methods. Machine-data can easily be varied to see the impact on the method. The research shows that sophisticated longwall methods increase the productivity of the system. The paper presents the results of the calculation with ProSL and shows how higher efficiency and lower costs can be achieved.

Dec 6, 2010

By E. h. Erwin Gaertner

Before dealing with the technical equipment of this paper a short survey of the Rhenish Brown Coal Area is given in order to illustrate the special geologic and environmental conditions in this region, which led to the development of the mining technics, used today.

Jan 1, 1975

By E. V. Koporulina, E. L. Chanturiya, M. V. Ryazantseva, E. S. Zhuravleva

"The morphology of the surface of sphalerite, galena and chalcopyrite and the adsorption of butyl xanthate under conditions of preliminary treatment of minerals by the products of water electrolysis were studied using atomic force microscopy (AFM) and Diffuse Reflection Infrared Fourier Transform Infrared Spectroscopy (FTIR). It was determined that practically all types of treatment by electrochemically modified water (a product of non-diaphragmatic treatment, anolyte and catholyte) lead to an increase of surface roughness of the studied minerals due to formation of small rounded shape particles. In contrast to that, after treatment of chalcopyrite by anolyte, its surface becomes smoother. Various effects of treatment by the water electrolysis products on the adsorption of chemical and physical forms of butyl xanthate on the studied sulfides were established. As a result, the efficiency of the complex of AFM and FTIR methods, as one of the ex-situ approaches for monitoring the surface state of sulfide minerals and direct investigation of BKx adsorption products was demonstrated.INTRODUCTION In mineral processing, copper-zinc sulfide ores are one of the most complex products in view of their mineral composition, fine dissemination, complex inter-growth and the proximity of the technological characteristics of copper, zinc and iron sulfides. For the most complete disintegration, fine grinding of ores to a size of 0.074-0.044 mm is necessary. Consequently, the main method for processing of such ores is flotation, which bases on the difference in physical and chemical properties of the mineral surfaces, in particular, degree of wettability. The separation of copper and zinc minerals and their separation from ferrous and other sulfides, sulfosalts and rock mineral is a very difficult task (Chanturiya, 2000). For the successful separation of copper and zinc minerals in the appropriate selective concentrates, it is necessary to find conditions for the most complete liberation of ore and rock-forming minerals and for increase the contrast in physical and chemical properties of their surfaces. Despite significant progress in the processing of copper-zinc sulfide ores, the problem of the selectivity of the separation of the main ore minerals has not yet been fully solved and requires innovative approaches (Chanturiya, 2015). To date, various methods of preliminary energy processing of complex ores are used: magnetic pulse treatment, impact by high-voltage nanosecond pulses, electrochemical effects (including products of water electrolysis (Chanturiya et al., 2014; Bunin et al., 2015; Chanturiya et al., 2014a; Chanturiya et al., 2016), processing with flotation reagents, etc. Electrochemical treatment of water in various modes allows to obtain products of electrolysis with different oxidation-reduction properties: acid anolyte with a high oxidation potential and dissolved oxygen content, an alkaline catholyte with high reducing properties and a product of non-diaphragmatic treatment with enhanced reduction properties."

Jan 1, 2018

By Tyler Roberts

New Afton mine is an 11,000 tonne per day block caving operation, located 8 km west of the city of Kamloops, British Columbia. Due to the nature of block caving and the weak rock mass at New Afton, the mine has faced and overcome many blasting challenges during its ramp-up to commercial production. As New Afton Mine continues to grow the demand for drill and blast precision has continued to grow as well; any misstep incurs delays in achieving full production capacity. The block cave mining method used at New Afton employs single-shot draw-bells, fired with very little void and blind undercutting, allowing little margin for error. New Afton has made continuous improvements to its blasting strategy by reacting quickly to real-time problems and employing sustainable, repeatable solutions to overcome its unique blasting requirements. Examples of these solutions include: increasing blast hole diameter, casing production drill holes, developing pre-loading procedures and developing strategies for remotely blasting under-broken remnants in both draw-bells and undercutting. Increasing the blast hole diameter has alleviated initial problems with hole plugging in the highly jointed rock mass at New Afton. This has reduced drill-cleaning time significantly and enabled New Afton to meet blasting targets. PVC hole casing was trialed when blasting in extremely fractured ground, where drill holes continually plugged. The casing allowed the drill holes to remain open long enough to load and blast. Calculations were carried out in order to achieve the same explosive energy in the cased holes as a typical blast. Results were generally positive, but more testing is required. Production flexibility and scheduling reliability have been maintained at New Afton by developing a pre-loading procedure for the production undercutting. In doing so, New Afton has been able to keep productivity high by having a flexible production schedule that is not reliant on a specific piece of equipment or production drive to remain productive; this flexibility is because the mucking of undercut material can occur at any stage of the drill/blast/muck cycle. New Afton has developed a strategy for blasting remnant under-break in its draw-bells and undercutting by remotely drilling holes near to the under-broken section and then loading the toes of these holes with emulsion, the remainder of the hole is then filled with grout. The holes are grouted in order to prevent damage to permanent pillars between draw-bells (where the majority of the recovery holes need to be located). Several critical areas were recovered using this technique with little to no damage to the remaining permanent pillars. Innovative blasting solutions have allowed New Afton to overcome obstacles in order to become a producing operation. Moving forward, New Afton looks to continue its trend of innovative drilling and blasting techniques when faced with out of the ordinary situations.

Aug 1, 2013

By Sean Masse

New Gold?s New Afton Mine, located 8 km (5 miles) west of Kamloops, British Columbia, is a 4.5-Mt/a (5-million stpy) block cave mine, making it the highest tonnage underground hard rock mine in Canada. The reserve is estimated at 52.5 Mt (55.9 million st) with grades of 0.65 g/t (0.02 oz/st) gold and 0.93 percent copper (2012). Commercial production was achieved in July 2012 and nameplate production was achieved ahead of schedule in September 2012, with the cave breaching to surface in 2013. The mill has a SAG and a ball mill with a froth flotation circuit.

Jan 1, 2014

By O. A. Bascur

The problem of setting the proper control objectives and/or having several objectives to be met in the implementation of grinding control strategies can be resolved. The design and implementation of a distributed control system for safe operation of a grinding circuit while maximizing profit is presented. An optimal recovery/throughput target for a desired grind is accomplished by advanced control strategies at the DCS level. A mill load constraint control technique provides stable operation with a substantial increase in throughput, while the desired grind index is maintained by an inferential grind control technique without using a particle size analyzer. The integration of crushing/grinding and flotation in the overall design was the key to the success of the project. This synergistic effect was obtained by implementing a computer -plant management system in the concentrator. The overall philosophy of keeping the implementation simple but not simpler was used.

Jan 1, 1989

By B. R. Arvidson

Sharper separation and improved control of the top size increases the fine particle product yield. As the milling circuit recycle stream is reduced, the overall capacity is increased. In some cases, a doubling of throughput is realized, although 25 to 30% increase is more typical. Alternatively, the energy demand may be reduced, although the best economic improvement results from higher capacity. A comparison with a high-pressure roller mill circuit shows that an optimized ball mill circuit retrofitted with the new air classifier has lower energy consumption. The new air classifier features low energy demand and substantially lower maintenance compared to similar equipment. Design and operation of this recently patented classifier are discussed. Several industrial installations will be described.

Jan 1, 1999

By Jan Klein

"The last decade of the 20th century saw the development of one of the last missing geophysical tools for mineral exploration: the Airborne Gravity Gradiometer. It is possible that Airborne Induced Polarization, one of the stillelusive systems, will make its debut in the next few years. In this sense, the paper point out are the most recent and important improvements in geophysical technologies for mineral exploration. Airborne techniques are followed by the systems used on the ground and in boreholes. New equipment and data processing and modeling software are referred to. Brief remarks are made about developments that can be expected in the years to come, these will be mainly focussing on deep search in rugged and conductive terrains. "

Apr 24, 2001

By P. J. Mackey

New and emerging, as well as proven technologies for the smelting of copper, nickel, lead and zinc are briefly reviewed. The number of new technologies available today is greater than at any time in the past, and interest and development activities remain high despite the economic dif-ficulties faced by the non-ferrous metallurgical industry. Part of the impetus is provided by the realization that only the most cost effective producers will remain competitive, and that new technology is one key to cost effectiveness. The commercially proven "new" copper smelting processes can now be considered to be conventional- technology, and are expected to dominate copper smelting for acme time. There is a growing. interest in continuous copper converting, although direct smelting and converting to copper in one vessel remains the- ideal. There is little activity in nickel smelting. After many years. of development, it appears that several new direct lead smelting processes will soon be a commercial reality. The electrolytic zinc process is expected to continue its dominance, although there is a renewed interest in pyrometallurgical approaches. One of the new zinc processes, and a molybdenum smelting process, illustrate the possibilities of using plasma technology in non-ferrous metallurgy. In the area of complex sulphides, there is perhaps less interest in the treatment of bulk con¬centrate, and more in the treatment of so-called dirty copper concentrates. Much of the technology ancillary to smelting has remained relatively unchanged, and more effort must be made to advance the technology in areas such as materials handling, gas cleaning and sulphur fixation, and energy recovery. More attention to engineering design is also needed. Escalating capital costs may make mini-smelters attractive, but imaginative technology and innovative engineering will be required to make them cost effective. Finally, a glimpse is offered of the smelter of the future.

Jan 1, 1983

By Eric Yoshimitsu Sako

One of the main difficulties in the operation of trough and runners at Arcelor Mittal Tubarão (AMT) Blast-furnace no.02 is the reduced amount of time available for repair procedures. The consequence is that the castable installation must often be performed during hot conditions and the installed castable could easily detach from the base material during the early stage of operation, exposing the previously oxidized base material to molten iron and corrosive slag attack. When events like this happen, emergency repairs must be executed, resulting in increased refractory unit consumption and an unplanned shutdown of unit operation. Considering these targets, Nippon Crucible Co. and Saint-Gobain HPR Brazil have developed a high-performance Al2O3-SiC-C composition based on an entirely novel anti-oxidation technology. Oxidizing reactions could be attenuated by adding an oxidant inhibitor and a water reducing agent. As a result, the open porosity was significantly reduced, resulting in an improvement of campaign life in terms of pig iron throughput when compared with the regular castable. An analysis of this life improvement showed successful results for the material after 250 days of campaign. The main reason for such successful results was that the deterioration caused by the oxidation was significantly less and that this change made on the high cohesive structure of the base material was maintained for a long time. The attained results allowed Arcelor Mittal Tubarão to achieve longer trough campaigns, and avoid any unplanned stoppages with zero breakdown risks.

Oct 30, 2017