Search Documents

By M. L. Requa

In the fall of 1910, the Nevada Petroleum Co., operating in the Coal-inga field in California, determined to drill a number of wells with rotary tools, in order to prove conclusively the relative value of the rotary as compared with the standard rig. At that time, the rotary was but little known in California and its proposed introduction met with considerable criticism on the part of the operators and quiet opposition among the standard drilling crews. There were few men available who were competent to handle a rotary outfit, and these few had had but little experience in California fields. Machines as then built were much inferior to those now used, being lighter in construction and of a poorer quality of material. The shells encountered at depths between 1,700 and 2,000 ft. seemed to be too hard to permit of successful drilling, and at these depths the rig was changed over to standard tools and by them completed. Because of the heavy depreciation, the time lost in converting from rotary to standard, and the comparatively small profit, it was concluded that unless in the future there was some material improvement in rotary rigs, nothing would be gained by drilling with rotary tools upon this property. Little or no drilling has been done upon the property since that time, but in the meantime a large number of men have been trained in the use of the rotary; in fact, many standard-tool men have abandoned standard drilling and, starting in as roustabouts, have become thoroughly competent rotary operators. The improvements in the machinery have been such as to remove many of the objections and the rotary drilling of to-day is in every way superior to that of 1910. In contrast, a well drilled recently by the Kern Trading & Oil Co., in the east side Coalinga field may be cited. The first 2,500 ft. was drilled in 24 days and it is confidently expected that the water string will be set with a rotary at 3,400 ft.—a record obviously far beyond that made in 1910 by the Nevada Petroleum Co. The records herewith are published with the hope that some one having more recent data will publish them so that comparison may be

Jan 1, 1915

By Robert W. Hunt

I have frequently stated that while the chemical composition of steel is important, yet even greater importance is connected with the mechanical and heat treatment of the metal. During the past year I encountered such a positive example of that fact that I deem it worth putting upon record. A prominent railway system divided an order for open-hearth steel rails between two steel works, both of which are under the control of the same corporation; giving to one about 18,000 tons, and to the other 7,500 tons of the same section and to be made under the same specifications. The rolling results obtained in the two mills varied so widely that a study of the figures is intensely interesting and serves to illustrate the advantages obtained by carefu1 ingot casting, and, quite as pertinently, the possible benefits of careful subsequent heating and rolling with moderate reductions in the rolling process. The smaller order was rolled complete in four installments during the same months that the larger order was being made in six separate installments; but, to permit of exact comparisons, the totals of the four installments (completing the order with the mill which I will call A) are given with the totals of the first four installments of the larger order, made by the mill designated as B. These rolling results are: Mill A. Mill B. Number of rollings,............................................ 4 4 Total number of rails rolled................................ 18,278 27,832 Percentage of rails cut to short lengths because of flaws near ends, etc......................................... 0.7 7.6 Percentage of rails made second quality for flaws, etc. 0.9 6.3 Percentage of rails scrapped for flaws, etc............... 0.6 4.5 Percentage of rails scrapped for failure at drop test... none 3.4 It should be stated that the figures given above cover all the reasons for putting the rails in the classes stated, Thus a part of the percentage of rails cut to short lengths may have been

Jan 1, 1914

By W. H. Bassett, C. H. Davis

In the commercial annealing of cartridge brass there are four points regarding which definite data are essential. They have to do with the correct interpretation of grain count in its relation to annealing temperature and, incidentally, to Brinell hardness. These points are: 1. The comparison of the grain sizes of two cartridge-brass mixtures: 69 copper, 31 zinc, 0.376-in. (9.5-mm.) gage; and 68 copper, 32 zinc, 0.130-in. (3.3-mm.) gage 2. The comparison of the grain sizes of annealed metal that had previously been reduced by rolling varying amounts; for instance, 20.0, 36.6, 50.9, and 59.1 per cent. 3. The determination of standards for grain sizes on annealed brass of the composition 68 per cent. copper, 32 per cent. zinc and 69 copper, 31 zinc. 4. The comparison of grain size with Brinell hardness on identical samples of annealed metal. In their comprehensive and thorough investigation of the recrystal-lization of cold-worked alpha brass on annealing,l Mathewson and Phillips have discussed the relations between temperature of anneal, degree of deformation, and structural alteration in alpha brass. They have also shown certain comparisons between the ordinary physical properties and the grain size of annealed brass. The purpose of the present investigation is mainly concerned with the grain size of cartridge brass, its relation to Brinell hardness, and the publication of sufficient data to enable those engaged in the inspection of such material to have a correct foundation upon which to work. The first alloy was taken from regular mill stock that had been rolled from 0.580 in. to 0.376 in. (14.7 mm. to 9.5 mm.) gage, a reduction of 35.1 per cent. This bar (No. 1) had the following composition: Copper, 69.20 per cent.; zinc, 30.76 per cent.; lead, 0.02 per cent.; iron, 0.02 per cent. The second alloy was also taken from mill stock of 0.325 in. (8.25 mm.) gage and was rolled as shown in Table 1, in order to get four bars reduced two, four, six, and eight B. & 5. numbers respectively. This second alloy

Jan 1, 1919

By J. Brian Eby

Contact metamorphism of coals is any physical or chemical change in the character of a coal directly attributable to heat of surface or intrusive igneous rocks. Coal beds so affected are found in the United States, England, Alaska, Mexico, New Zealand, Greenland, and other countries. Particularly in the United States, there is a wide occurrence of contact altered coals; conspicuous examples are found in Colorado, Utah, New Mexico, Illinois, and North Carolina. During a recent examination of coal beds on Yampa River, in northwestern Colorado, the author had an opportunity to make some detailed observations on the contact metamorphism of coals. In this field, coals over an area of 20 sq. mi. have been affected by dikes, sheets, and sills;' samples of the coals were systematically collected and analyzed,2 with the view of obtaining more specific data on the character of these alterations. The investigation was threefold in purpose: to secure information on the lateral effects of a dike cutting a coal bed, on the range in vertical effects on coal beds overlying sheets or sills, and on the range in the vertical effects on coal beds underlying sheets and sills. Favorable field conditions, such as fresh outcrops and newly dug prospects, made possible many of the field observations and collections. The coals studied in this field belong chiefly to the Mesaverde and 11Laramie" formations. The Mesaverde coals, on the average, are blocky low-rank bituminous coals; the "Laramie" coals, which are considerably younger, are of subbituminous rank. The coals of both formations, in the northeastern part of the Yampa field, have been greatly affected by basalt intrusives, yielding all variations of carbonized coal from natural coke to the unaffected material. The igneous rock that directly affects the coals is a fine-grained olivine basalt that is intruded, in sheets up to 200 ft. thick, into the coal-bearing

Jan 1, 1925

By William R. Webster

The unusual interest taken in the papers on steel at the New York (1922) meeting showed that the time is ripe for the renewal of the general discussion of the physics of steel, on the same lines that wete used formerly and produced such good and lasting results. The curves shown in Figs. 1 to 4 and the appendix were added to my paper1 after the February meeting, but, unfortunately, Figs. 1 and 3 were transposed; the curves on page 252 are for bessemer steel and belong on page 254; while those on page 254 are for open-hearth steel and belong on page 252. These errors are evident at once on referring to the data in Tables 1 and 2, pages 227 and 228. The curves for each 0.05 per cent. of carbon and manganese in basic open-hearth steel are given in Figs. 1 and 2; these lines for the lower carbons and manganese are comparatively uniform. Figs. 3 and 4 give similar lines for carbon and manganese in bessemer steel. The large break in the carbon lines from 0.55 per cent. to 0.60 per cent. is caused by much higher silicon in the steels of 0.60 per cent, carbon and over that are used for springs, etc. The estimated ultimate strength of pure iron, and the increase in strength by carbon, phosphorus, and manganese, with the different views regarding the same, were given and diseussed. All of this can be considered as an introduction to the practical use that is now being made of such data in selecting the heats of steel best suited to give the required physical tests called for in the finished rolled material. The chemical composition of the steel, of course, tells only a part of the story, as many other factors that have an influence on the physical properties of the steel must be considered, and controlled as far as is possible. Some of these have already been referred to, but there are other important ones to be considered and discussed.

Jan 1, 1923

By William R. Webster

The unusual interest taken in the papers on steel at the New York (1922) meeting showed that the time is ripe for the renewal of the general discussion of the physics of steel, on the same lines that wete used formerly and produced such good and lasting results. The curves shown in Figs. 1 to 4 and the appendix were added to my paper1 after the February meeting, but, unfortunately, Figs. 1 and 3 were transposed; the curves on page 252 are for bessemer steel and belong on page 254; while those on page 254 are for open-hearth steel and belong on page 252. These errors are evident at once on referring to the data in Tables 1 and 2, pages 227 and 228. The curves for each 0.05 per cent. of carbon and manganese in basic open-hearth steel are given in Figs. 1 and 2; these lines for the lower carbons and manganese are comparatively uniform. Figs. 3 and 4 give similar lines for carbon and manganese in bessemer steel. The large break in the carbon lines from 0.55 per cent. to 0.60 per cent. is caused by much higher silicon in the steels of 0.60 per cent, carbon and over that are used for springs, etc. The estimated ultimate strength of pure iron, and the increase in strength by carbon, phosphorus, and manganese, with the different views regarding the same, were given and diseussed. All of this can be considered as an introduction to the practical use that is now being made of such data in selecting the heats of steel best suited to give the required physical tests called for in the finished rolled material. The chemical composition of the steel, of course, tells only a part of the story, as many other factors that have an influence on the physical properties of the steel must be considered, and controlled as far as is possible. Some of these have already been referred to, but there are other important ones to be considered and discussed.

Jan 1, 1923

By A. B. Kinzel

Since the exposition of the behavior of certain iron alloys by Sykesl involving the existence of an austenite loop and the discovery of such a loop in the chrome-iron system by Bain,2 there has been much conjecture both on his part and on the part of metallurgists in general as to the exact shape and location of this loop. In previous work commercial steel has been used and the microscope has been employed to locate the critical points so that the position of the loop has been quite approximate. Numerous attempts have been made to measure the critical points of the carbon-free alloys but all of these for one reason or another have failed. A satisfactory method for studying these phenomena is presented here. MateRial The first difficulty in this study was to obtain pure chromium-iron alloys. This has been overcome by melting in a vacuum electrolytic iron and chromium analyzing 99.84 Cr, Fe and C. A pure magnesite crucible was used and the melt allowed to solidify in the crucible. A typical analysis is chromium, 10.10 per cent., carbon, 0.006 per cent., silicon and manganese nil. To overcome the problem presented by segregation, ingots were made into wire 0.04 in. in diameter. This was accomplished by hand-forging the ingots into rods, using an oxyhydrogen flame for heating, in order to avoid carbon. Subsequently the rods were swaged to wire, the heating being carried out in hydrogen. Thus local segregation was eliminated although differences in analysis between portions 50 ft. apart were noted. An electric-resistance method was first tried to determine the critical points, but due to the physical defects in the wire this failed. Bain had previously shown the presence or absence of critical points in a qualitative way by observing the sag in a catenary. The author has devised the following method which gives an accurate determination of the critical points from expansion-temperature curves of suspended wire, a special telescopic dilatometer being used for the purpose.

By Howard Scott

The great advances made in mechanical engineering during recent years through the use of alloy steels, as illustrated by the development of the airplane and automobile, may be ascribed primarily to the application of nickel as an alloying element. The ternary system iron-carbon-nickel has a wide industrial application and forms, further, thefundamental basis of the even greater class of the widely used quarternary steels such as nickel-chromium, nickel-silicon, and nickel-vanadium. As is not uncommon with such cases of virile growth in an industry, the application of the alloy steel in a largely empirical manner has outstripped its scientific development so that a fertile field for metallographic research still remains. In this field, the basic nickel steels require first consideration and are the subject of the present investigation, which is offered as a preliminary to the study of the more complex alloys of industrial importance Of the principal tools of metallography—microscopic examination, determination of mechanical properties, and thermal analysis—the last has developed much more slowly in its application to industrial needs so that the situation often exists that heat treatment operations are based on empirically determined temperatures; that is, temperatures deterrnincd without regard to the actual transformation characteristics of the alloy. This situation is undesirable as there is no uniform standard for comparison of results. It is due, outside the usual difficulties involved in temperature measurements, to the pioneer character of much of the published work; to the lack of definiteness of the Ac, transformation,1 particularly in low-carbon steels; to the failure to define operating conditions completely; and to the paucity of information correlating thermal characteristics with results of heat treatment.

Jan 1, 1922

By Howard Scott

The great advances made in mechanical engineering during recent years through the use of alloy steels, as illustrated by the development of the airplane and automobile, may be ascribed primarily to the application of nickel as an alloying element. The ternary system iron-carbon-nickel has a wide industrial application and forms, further, thefundamental basis of the even greater class of the widely used quarternary steels such as nickel-chromium, nickel-silicon, and nickel-vanadium. As is not uncommon with such cases of virile growth in an industry, the application of the alloy steel in a largely empirical manner has outstripped its scientific development so that a fertile field for metallographic research still remains. In this field, the basic nickel steels require first consideration and are the subject of the present investigation, which is offered as a preliminary to the study of the more complex alloys of industrial importance Of the principal tools of metallography—microscopic examination, determination of mechanical properties, and thermal analysis—the last has developed much more slowly in its application to industrial needs so that the situation often exists that heat treatment operations are based on empirically determined temperatures; that is, temperatures deterrnincd without regard to the actual transformation characteristics of the alloy. This situation is undesirable as there is no uniform standard for comparison of results. It is due, outside the usual difficulties involved in temperature measurements, to the pioneer character of much of the published work; to the lack of definiteness of the Ac, transformation,1 particularly in low-carbon steels; to the failure to define operating conditions completely; and to the paucity of information correlating thermal characteristics with results of heat treatment.

Jan 1, 1922

By M. W. Ditto

THe conversion of the beehive coke plants, in this country, to byproduct plants has been slow, because the coal supplies were near the centers of the steel industry. With the growth of this industry, especially with its development around Chicago, it became necessary to transport large tonnages of coal from the eastern districts and then convert it into coke. The losses due to transportation costs were partly offset by the value of the byproducts recovered. To save the transportation costs, it was desirable that the coal deposits of Indiana and Illinois be utilized. This coal had always been classified as non-coking; it was also considered unsuitable for the metallurgical field because of the high ash and sulfur contents. The conditions, however, were promising enough to start experimental and development work, which crystallized in the design of the Roberts coke oven. The fundamental features of most coke ovens, with respect to the application of heating gas and the recovery of byproducts, are the same and, in the last few years, the tendency has been toward the better application of heating to the walls, higher thermal efficiency, and, by the control of heating conditions, the increase of byproduct yields. Structural features also have been improved and the use of high-grade refractory material has allowed the use of higher temperatures with the resulting higher rated capacity per oven per day. Great improvements have been made in both recuperators and regenerators, particularly with reference to the individualizing of each oven with respect to its adjacent oven, so that each can be operated as a unit if desired. The highest development of the flue type of oven has been applying individual regenerators for the recovery of waste heat. After some research work, it was found that the high-volatile Illinois coals could be utilized for coke by obtaining the better application and control of the heating conditions in the oven. Most of this high-volatile coal that had been used gave a good coke structure under certain conditions. The fact that coke was occasionally made from this coal, demonstrated the possibiity of making coke from it at all times pro-

Jan 1, 1923

By M. W. Ditto

THe conversion of the beehive coke plants, in this country, to byproduct plants has been slow, because the coal supplies were near the centers of the steel industry. With the growth of this industry, especially with its development around Chicago, it became necessary to transport large tonnages of coal from the eastern districts and then convert it into coke. The losses due to transportation costs were partly offset by the value of the byproducts recovered. To save the transportation costs, it was desirable that the coal deposits of Indiana and Illinois be utilized. This coal had always been classified as non-coking; it was also considered unsuitable for the metallurgical field because of the high ash and sulfur contents. The conditions, however, were promising enough to start experimental and development work, which crystallized in the design of the Roberts coke oven. The fundamental features of most coke ovens, with respect to the application of heating gas and the recovery of byproducts, are the same and, in the last few years, the tendency has been toward the better application of heating to the walls, higher thermal efficiency, and, by the control of heating conditions, the increase of byproduct yields. Structural features also have been improved and the use of high-grade refractory material has allowed the use of higher temperatures with the resulting higher rated capacity per oven per day. Great improvements have been made in both recuperators and regenerators, particularly with reference to the individualizing of each oven with respect to its adjacent oven, so that each can be operated as a unit if desired. The highest development of the flue type of oven has been applying individual regenerators for the recovery of waste heat. After some research work, it was found that the high-volatile Illinois coals could be utilized for coke by obtaining the better application and control of the heating conditions in the oven. Most of this high-volatile coal that had been used gave a good coke structure under certain conditions. The fact that coke was occasionally made from this coal, demonstrated the possibiity of making coke from it at all times pro-

Jan 1, 1923

By H. M. Howe, A. G. Levy

§ 1 Introduction.—This paper gives the results of our micro-graphic determinations of the position of Ae3 in a series of 14 hypo-eutectoid steels of varying carbon content, one of them very rich in phosphorus, and of SEe for one hyper-eutectoid steel. We have proceeded chiefly by noting the temperature at which the reabsorption of the pro-eutectoid element is found to be complete after a 30-min. holding, but in part also by noting the temperature at which its precipitation begins. Observations on these same steels by Messrs. Burgess, Crowe, and Rawdon, of the United States Bureau of Standards, are given in a paper1 issued simultaneously with this, while in a third paper2 one of us compares these data with those of earlier observers. These three papers are treated as one whole by numbering their sections, tables, and illustrations continuously, and by setting the folding plates of micrographs at the end of the last paper. The Composition of the Steels Experimented On is given in Table I. § 2. Notalion and Definitions.—Following Osmond's development of Tschernoff's notation, in which " Ac3 " is the upper limit of the hypo-eutectoid part of the transformation range as observed in heating up, and " Ar3 " is that same limit as observed in cooling down, and following the usual custom of calling the upper limit of the hyper-eutectoid part of that range " SE," we may go farther and call this latter limit " SEc" when observed in heating up and " SEr " when observed in cooling down. Further, we may call the equilibrium position of these lines, i. e., the position which they would have in pure iron-carbon alloys if all

Jan 1, 1914

By W. S. Ayres

I. Introduction. This cavern was discovered Oct. 32,1904, by Mr. Charles 8. Deutschman, in company with whom I made, May 29 to June 3,1905, at the request of Mr. Howard Douglas, Superintendent of the Canadian National Parks, the first exploration of it for the Canadian government. The results were stated in a paper, orally presented, with lantern-views from my photographs, at the British Columbia Meeting of the Institute, Victoria, B. C., July 5, 1905.* The present paper embodies also the results of a second examination, made Oct. 25 to 29, 1905. The accompanging map, Fig. 1, will serve as a guide to the following description. 11. Location. The cavern is situated at snow-line, at the head-waters of Cougar creek, on the west slopes of the Selkirks, about 2 miles north from Ross Peak water-tank, and 5.5 miles west from Glacier station, on the main line of the Canadian Pacific Railway. It was then reached by an arduous climb from the water-tank, up the ravine of Cougar creek, for 8,000 ft. (2,000 ft. of altitude) over rock- and snow-slides, and through a thick tangle of alders. But an easy and very picturesque trail has, during the past summer, been opened by the government from Glacier station, which is also a hotel of the railway company. Figs. 3, 3 and 4 represent views, not heretofore published, of the grand scenery of this region, so rapidly becoming the object of attraction to thousands of tourists from all parts of the world. These views, as well as those shown in Figs. 5, 6, 7, 8

Jan 1, 1908

By R. S. Archer

In the microscopic examination of aircraft-engine parts made of heat-treated alloy steels, the writer has been forcibly impressed by the failure of the usual etching processes to disclose any but gross defects in heat treatment. It seemed particularly desirable to bring out the grain size of the steel, which is indicated in the ordinary etching processes chiefly by the change in orientation of structure from grain to grain. After various attempts, a fairly successful method has been found, which is here presented in the hope that it may be of use to those who have occasion to examine these steels in the hcat-treated condition. The specimens worked with have been mostly chrome-nickel steels heat treated (that is, hardened and tempered) to a Brinell hardness of around 300. A few experiments with other specimens will be referred to later. Briefly, the method employed consists in etching the steel about 10 min. in a fresh solution of picric acid in ethyl alcohol, and then rubbing off the smudge of carbonaceous matter on moist broadcloth. Different samples of almost identical analysis, heat treatment, and physical properties (including resistance to impact) respond quite differently to this treatment. In some, the grain boundaries are developed quite readily, while in others, especially in those whose grain is unusually fine or in which the final hardening heat has not quite obliterated the previous crystallization, the results are more obscure. The exact time of etching to secure the best results also differs for various samples, and the greatest success is usually attained by a process of "tinkering." Such a process is illustrated in a series of micrographs, the first six of which were taken at a magnification of 300 diameters. The properties of the steel are as follows: Carbon, per cent............... 0.42 Brinell hardness.............. 293 Nickel, per cent................ 1.35 Yield point, pounds per square Chromium, per cent............. 0.90 inch........................ 131,000 Copper, per cent................ 0.025 Maximum strength, pounds per Manganese, per cent............ 0.74 square inch................. 144,500 Phosphorus, per cent............ 0.024 Elongation in 1 in., per cent... 28 Sulfur, per cent................ 0.036 Lod impact, foot-pounds...... 51 Reduction of area, per cent...... 57.3

Jan 1, 1920

By M. H. Merriss

Some years ago, at the plant of the Baltimore Copper Smelting & Rolling Co., the receipt of large quantities of copper blister running high in lead, nickel, and arsenic resulted in the formation of a great amount of very foul slag, in the anode furnaces. A typical analysis of this slag was: Gold, oz. per ton......... 0.09 Arsenic, per cent.......... 0.60 Silver, oz. per ton......'.. 13.20 Antimony, per cent........ 0.50 Copper, per cent......... 19.50 Silica, per cent............ 28.30 Lead, per cent........... 11.90 FeO, per cent............. 19.20 Nickel, per cent.......... 4.60 CaO, per cent............. 1.60 The problem was to get out the copper in marketable form, to save the gold, silver, and particularly the nickel, and to get rid of as much as possible of the lead, arsenic, and other elements that were valueless to the Baltimore plant. In a copper refinery that does not take custom material for matte smelting, the usual method is to smelt the anode slag with coke in a reducing furnace, the black copper thus formed being sent back to the anode furnaces; this was the custom at Baltimore. An average anode slag will contain, perhaps, 40 per cent. copper and such small quantities of lead, nickel, etc., that smelting will get rid of most of these impurities in the black-copper furnace slag. To treat such an impure slag in this way, however, would result in a large nickel loss, and would send back to the anode furnaces all the lead and nickel not so lost, where it would be slagged off again and returned to the black-copper furnace as a slag still more concentrated in impurities. The result would probably be a constantly increasing amount of anode slag containing a likewise constantly increasing percentage of impurities. To avoid such a disastrous closed circuit some other process had to be devised. A small multiple-tank room, built for impure copper as an adjunct to the main series electrolytic refinery, was available, so the following standard process was suggested:

Jan 1, 1924

By H. M. Howe

§ 24. Introduction.—This paper discusses the chief existing data as to the temperature, in iron-carbon alloys, of Ae3, the upper limit of the transformation range when in equilibrium, as distinguished from Ac3, the temperature at which the end of the transformation is noted in heating up, and from Ar3, that at which its beginning is noted in cooling down. The former is in fact carried above Ae3 and the latter below Ae3 by lag. I touch incidentally on the influence of manganese on Ae3 (§ 29, p. 614). The sections, tables, and illustrations are numbered consecutively with those in the accompanying papers by Howe and Levy on Determination of the Position of Ae3 in Carbon-Iron Alloys, and by Burgess, Crowe, and Rawdon on Thermal and Microscopical Examination of Professor Howe's Standard Commercial Steels, to which the present paper forms a sequel. § 25. The contradictoriness of our present evidence is shown by grouping it together in Fig. 14. For instance, both Goerens and Meyer (Series 2) and Meuthen (Series 12) used practically stationary temperature, and thus reduced the influence of lag very greatly; yet Ae3 for 0.32 carbon steel according to the former investigators is 894", but according to Meuthen it is at or below 770°, a discrepancy of 124" or more. In view of our ability to measure these high temperatures within a few degrees, the existence of such a discrepancy is as unwelcome as it seems needless. I attack the thankless task of bringing some order out of this chaos. In Part 11. (§§ 29 to 39) I consider the chief causes of error. In Part III. (§§ 40 to 48) I apply certain corrections to some of the existing data, review those data, weight them, and calculate a prob-

Jan 1, 1914

By Lawrence Veiller, D. Eppelsheimer

D. Eppelsheimer, * Middletown, Ohio.—The housing of employees has so many and so varied aspects that in order to reach even an approximately correct solution it is necessary to have in mind a few fundamental principles; but it is not possible as yet to write these housing principles in the clear and correct form that is possible with many of our natural laws. Manifestly, the problem depends first on the kind of people it is necessary to house. What is suitable for the Southern unattached negro is not suitable for the married skilled American. The influx of colored labor has affected quite a number of what were satisfactorily housed communities. The second important factor is the relative proportion of the number of employees to the total employable population of the community in which the industry is located. The employer of a hundred men in a large city has little responsibility in the matter of housing his employees. If he employs 75 per cent. of the employable population in a community of 27,000, as is the case of the company with which the writer is connected, it means a large responsibility. In the establishment of an entirely new plant in a more or less isolated place, the responsibility becomes greater. As engineers, we design and write the specifications for the machinery to accomplish a definite purpose, and proceed to house it, provide the necessary buildings with their accessories in the way of cranes, or heating systems, or sprinkling systems, as the case may be. There is no reason why the operating force should not be built up in very much the same way: design the organization, write its specifications so that the employment department can secure the proper men, and then house that organization with just as much thought and care as is given the plant. In the plant, the various machines will work along certain definite lines and accomplish certain results; but even if we start with the proper organization it takes considerable time to get that organization working together. One of the most important elements to this end is the proper housing of the organization. A man usually spends more time at home than at work. Proper surroundings and a comfortable, convenient house of good appearance exercise an influence that cannot be denied, and an employee situated in such surroundings is far more inclined to follow the policies of his employer and take an active part in furthering them than one dissatisfied with his home and surroundings, which feeling

Jan 1, 1919

By H. E. Doerr

The writer has been unable to find much information relative to tests made to determine the effect of forging on the specific density of steel. The opinion, however, among men engaged in the business, seems to be that forging greatly compresses or consolidates the steel. While such is doubtless the case with spongy or porous steel, the following experiments indicate that there can be little or no change in the density with steel initially free from cavities. Ten ingots of basic open-hearth steel cast as shown in Fig. 1 were used in the experiments. All the specimens were 0.53 carbon with all other elements the same, the analysis being determined from drillings taken midway between the center and outside of the upper end, as shown in Fig. 2. The specimens were selected from over one thousand ingots so that the tests could be comparative for the work done in forging only, but no two of the ingots were cast in the same heat. Each ingot remained in the mold approximately 30 min., when it was removed and sir-cooled. About 12 hr. later, when the temperature had been reduced to approximately that of the surrounding atmosphere, the head was discarded and the ingot heated in an oil furnace to approximately 2250" F. (1235" C). Approximately 1 min. was required to forge under the steam hammer to 1 1/4 in. (31.75 mm.), rough diameter, as shown by the dotted lines in Fig. 2. All ingots were allowed to air-cool after forging. Cylinders 1/2 in. (17.7 mm.) in diameter and 1/2 in. high were then turned from the forged and unforged parts of the ingots and numbered. The ten pairs of specimens were submitted to Louis E. Endsley, Professor of Railway Mechanical Engineering, University of Pittsburgh; A. N. Talbot, Professor of Applied Mechanics, University of Illinois; L. Z. Slater, chief chemist, Scullin Steel Co., St. Louis, Mo. NO information was furnished as to which specimens were forged or unforged and each laboratory used the same specimens, submitting the average of three independent determinations, a tabulation of which is shown in the accompanying table in which the laboratories are designated by the letters A, B, and C. While there is considerable difference in the individual determinations for a number of the specimens, the averages

Jan 1, 1920

By Arthur Knapp

NO oil territory in the world has been so rich in large producing wells, in a comparatively small area, as the Baku field. Particularly is this true of the Bibi Eibat field, which formerly produced millions of "poods " of " gusher," or as it is called in Russia, "fountain" oil. The Bibi Eibat and Balachany fields have been exhausted of gas and ruined by water, but ' the Surachany and Benegadi fields are still fountain territories and: many outlying districts that have only been prospected produce rich fountains. The method of controlling fountains, or gushers, is the result of growth, along with the Russian system of drilling, where large diameters and riveted casing have been in vogue. The screw casing is seldom used except to exclude water. Formerly the method of finishing wells and the condition of the casing at the top of the well would not permit the use of gates, manifolds, and connections as is standard elsewhere. The life of the flowing wells is very short, particularly those 10 in. (25 cm.) or more in diameter, which produce large quantities of sand and often flow for but a few days and are then a complete loss. More than 1,000,000 poods in 24 hr. have been claimed in several instances, but in no case was the flow for more than a few days. The oil sands of this district are free uncemented sands and vary in thickness from paper thin to a maximum of 10 ft. (3 m.). The sands are interlaid with strata of soft clay. In spite of this, the practice has been to drill into such sands and produce from the open hole without screen or liners. Sometimes the casing is set below the oil sand but in this case holes from 21/2 to 3 in. in diameter are drilled opposite the oil sand, which would not have the effect of a screen. Fig. 1 is an outline of the fountain shield ready for the control of a fountain. It is composed of an inner and an outer covering made from rough boards. The framework is made of rough round poles. When a light flow is expected, only the inner lining is built; and when the fountain comes in unexpectedly, it is often possible to build only the outer cover. The bridge is for the purpose of renewing the blocks as they become worn by the flow. The lower block, as here shown, is made of hardwood and is bolted to the crossbeams with brass bolts. The grain end is toward the flow. The upper block, as shown here, is made of cast steel and is also bolted to the crossbeam with brass bolts.

Jan 1, 1921

By Linn Bradley, W. W. Strong, H. D. Egbert

Marked differences of opinion have been expressed by engineers interested in cleaning iron blast-furnace gases for use in hot-blast stoves and under boilers, in reference to the advantages of a hot-dry method over a cold-wet method. One point at issue involves the sensible heat energy in the moisture contained in the gas. Some advocates of the cold-wet methods claim that the condensation and resultant removal of the greater portion of this contained moisture by wet scrubbing, spraying or similar methods, results in a saving of some of this sensible heat energy, by reason of the fact that water vapor has a high capacity for sensible heat energy and may carry from the exit of a hot-blast stove, for example, more heat units than are sacrificed or lost when the gas is cleaned by this cold-wet method. Other advantages claimed for the latter method are: That gas burns more readily when it is free from moisture in any form; that because gas is made denser by cooling and removing the moisture it has a higher calorific value than hot gas carrying moisture; and that higher flame temperatures are obtained when the gas is cleaned by the cold-wet method. A search through the available literature fails to disclose any extensive calculations or records of conditions obtained in practice, bearing upon these phases of gas cleaning. This paper deals with these problems from the standpoint of the economy of using a gas of higher flame temperatures, of improved stove design, and of economy in the gas-cleaning department. Calculations have been made which show that by cleaning the gases by a cold-wet method the sensible heat energy of the blast-furnace gases is greatly reduced; and, in general, this loss of heat energy is far greater than that lost from the stoves or boilers due to the sensible heat capacity of the water vapor if carried away by the exit gases. By making use of the

Jan 1, 1917