Search Documents

By Harry Wilton-Clark

Introduction Coal cleaning may be taken as meaning the separation of coal-as-mined into two or more fractions. Coal cleaning includes coal washing, together with any other means used in the ultimate preparation of coal prior to shipment (as coal) . The method of coal cleaning devised for any given mine must be one which is based entirely on the economic results obtainable. The installation of a high-cost and complex washing plant, designed to produce a low-ash dean coal, at the highest possible recovery, may be unsound practice. A crude 'roughing' washer may be the best result of sound engineering and operating consideration, and in some cases coal cleaning should be confined entirely to preparation at the face. Consideration of complete costs, to the point where the coal is actually sold, may show that certain seams are workable or not workable. Of the seams found workable, extraction of the whole or parts of the seam may be decided on. The portion to be extracted may contain rock or bone partings, which must be removed. It may be good practice to mine the extra portion and remove the objectionable materials by surface washing; or it may be that such materials should be removed underground, even at an increased mining cost. For instance, in some of the steeply pitching seams of the Alberta Crow's Nest Pass district, the removal of bone and rock at the face may be almost impossible under the usual 'up the pitch' or 'angle' mining methods, but possible by mining across the pitch so that the material to be rejected can be removed and gobbed. Again, if a complete seam is being extracted, investigation may show marked differences between top coal and bench coal, and if sufficient mine cars are being loaded from a chute at one time, the fact that such a place is working top or bench coal at the time may be reflected by peaks in ash content or size proportions at the ripple. It may be very effective coal preparation to smooth out such peaks.

Jan 1, 1934

By H. C. M. Gordon

IN every co al mine the hazard of fire in the underground workings is always present. This is a natural condition, because the mineral wrought and the supports normally used are themselves combustible and because underground fires may originate in many ways. The main causes of such fires are: (1) Open lights igniting gas, wood, or the coal itself. (2) Explosives igniting gas or coal. (3) Spontaneous combustion. (4) Electric sparks or short circuits igniting gas, wood, or coal. (5) Frictional heat igniting wood, coal, or oily material. (6) Explosions of gas or coal dust igniting wood or coal. The relative importance of these causes, and others less frequently met with, varies from district to district and depends to a great extent on the equipment and supplies used, on the training and discipline maintained among the workmen, and on the liability of the coal to heat spontaneously. It follows, therefore, that open lights should not be used and that, wherever there is the least possibility of methane being encountered, only locked safety lamps of an approved type should be allowed underground. It follows, also, that only 'permitted' explosives should be used and that the it use should be confined to conditions under which they are ?permitted?. Similarly, electric equipment should be of an approved type and all such stationary equipment should be housed in well-ventilated fireproof rooms. Such rooms, as well as entries to stables and oil houses, should be provided with doors which can be easily and tightly closed and which should be constructed of fireproof material.

Jan 1, 1937

By H. C. M. Gordon

MR. A. D. BADOUX: I have listened to Mr. Gordon's excellent paper with great interest, as I personally have gone through some of the experi­ences he has so clearly depicted. In particular, there were a good many times when we were greatly exercised in our minds as to whether we were justified or not in closing-off certain sections in the Allan mine. The difficulty in these cases arose from the fact that a peculiar smell could be detected in these sections but at the same ti me there was no positive evidence of spontaneous combustion either from heat being apparent or from the possible indications of fire getting any worse. It was suspected that the small percentage of -carbon monoxide that could be obtained by analysis in the air in these sections, and also the peculiar odour, were emanating from the coal itself, and, in order to verify this, bore-holes were drilled in the coal and the gases released from these bore-holes were analyzed. They were found to contain carbon monoxide. After quite a considerable length of time this contained carbon monoxide gradually diminished and finally could not be detected when analyzing such samples of gas. It was our intention to follow this matter up further, as such an occurrence of carbon monoxide is practically unknown, but the sections in which these occurrences were found had to be abandoned. Mr. Gordon referred t0 a case of spontaneous combustion in the Allan . mine, and I may say that, although the section in which that occurrence took place was travelled and carefully examined every day by the colliery officials, yet nothing unusual was noticed until the fire actually took place. This tire was the cause of a slight explosion.

Jan 1, 1938

THERE are two general classes of problems in connection with electric furnaces. First, those relating to the best utilization of the electrical power inside the furnace; second, those connected with the bringing of the electrical power to the point where it is to be utilized. Referring particularly to the latter class of problems, many calculations have been made, covering a wide variety of furnaces, to check the electrical capacity and power factor found from test. The following analysis, made for the purpose of determining the maximum capacity and approximate performance of a new furnace, to operate at 160 volts on a 60-cycle circuit, may be of interest. The first characteristic necessary to determine is the inductance, since this is the factor that limits the amount of power which can be put into the furnace. Inductance is calculated from the dimensions of the furnace, according to formulas of the U. S. Bureau of Standards,1 as

Jan 10, 1918

By E. Godfrey

The average man one meets on the street thinks of an explosive as a medium of death and destruction, something unstable which should be given a wide berth, because he knows little or nothing about its use or its stability. Briefly, explosives are compounds that develop very large quantities of heat and gas in an extremely short time and in a small space, thereby exerting enormous pressure upon surrounding bodies, and by the rapid expansion of this highly heated gas are able to perform a considerable amount of useful work. The amount of heat generated and the volume of gas produced by the decomposition of an explosive determines the amount of mechanical work it can do, and the time occupied by its change from solid or liquid condition to gaseous condition determines its shattering effect. Explosives manufactured by reputable people are not extremely dangerous, on the other hand they are quite safe if handled in a proper manner. Furthermore, before an explosive can be placed on the Canadian market a sample must be submitted to the Explosives Division of the Mines Department, who may condemn or permit its manufacture, according to their findings regarding its safety in handling and its stability during storage.

Jan 1, 1926

By W. G. Millar

Until a fire occurs, insurance and prevention work are often looked on as unavoidable necessities, but as insurance is back of all business credit, it is essential to know that in case of damage money will be available to cover the loss; while the interruption of production, often caused by a fire, brings home the realization that if prevention work avoids such an interruption, it is well worth while. Fire insurance is a legal contract guaranteeing the payment of large amounts to an owner, but it is possible there is no other important contract that receives so little consideration. Although previously carried on elsewhere, it is only of recent years that insurance engineering has been actively followed up in Canada, with inspections of an owner's property carried out for his benefit. Now inspections of this kind are made, advice on fire prevention and protection work ?is available, reports with recommendations with regard to the above are furnished periodically, and with this method applied the owner receives the broadest possible cover and security at the lowest cost. Rates are set by the underwriters by rating schedules which charge for defects in a building and allow credits for protection and other favourable features . These schedules are based on the past record of loss of mining properties as a class, so that a fire in another mining property indirectly affects you, but the amount paid is reduced in proportion as your property is improved. The writer feels, from personal experience, that there is no industry where fire prevention receives more attention than the mining industry, and it is a pleasure to advise that, due to this co-operation, some reduction in the basis rates for mining risks is now being made by the underwriters.

Jan 1, 1928

By John M. Hartman

(Read at the Wilkes-Barre Meeting, May, 1877.) Two systems are used for heating air in blast-furnace operations I. The double surface system, in which a cast-iron pipe is heated on the outer surface, and, at the same time, heats the blast from its inner surface. This is simple in operation and gives a continuous effect, but is limited by 1100° F. as a maximum temperature of the blast. II. The single surface system, by which large surfaces of fire-brick are heated, and air passed over the heated surface, absorbing the heat and carrying it on to the furnace. This system is more complex than the double surface, as it involves the reversing of the air and gas every hour and a half. The single surface system has two advantages: 1. The blast can be heated to a temperature of 1800° F. 2. The stoves are indestructible. From recent experience it has been found that 1300° F. to 1400° F. is the best average temperature for economy of coal for safe work¬ing. This is equivalent to a saving of 12 to 2 cwt. of coal per ton, of iron over the extreme limit of cast-iron stoves. Independently of this, it is a strong point in favor of this system that the blast can be raised to a temperature of 1800° F. within an hour when the hearth is getting cold. All furnacemen know the value of a hot hearth for quality and quantity of iron. Cooling of a hearth occurs from leaky tuyeres, scaffolds, or heavy burden. When there is not sufficient coal at the tuyeres to seize on the oxy¬gen of the entering air and convert it at once to carbonic oxide, there will not be enough heat to liquefy the cinder. Black cinder and poor iron are the results. The remedy is additional heat from the blast. If the stoves will give 1800° in place of 1100°, it is obvious that the furnaces will get around sooner, and without waiting for a change of burden at the tunnel head to bring extra coal to the hearth. The heat absorption caused by a leaky tuyere will chill the hearth and drive the zone of fusion higher up in the furnace. This loss must be supplied, and the calories lost to the hearth must be regained before good iron can be made. Take another case : A furnace carefully burdened on No. 1 iron, during a spell of damp weather, goes on to No. 2 or No. 3. Heat is lost to the furnace through absorption by the moisture, and less burden must be carried in order to get back on No. 1. When the

Jan 1, 1878

ARTHUR CROWFOOT, Morenci, Ariz. (communication to the Secretary*).-In order to set at rest any doubts in regard to the reasons for selecting the Callow pneumatic flotation process for use in the concentrators of the Arizona Copper Co., Ltd., at Clifton and Morenci, I am presenting the following facts gained from the results of test work carried out on the Callow and Cole-Bergman types of flotation machines at Morenci. Prior to the comparative test of merit between the Callow and Cole-Bergman machines, many months' time and a large amount of money had been expended in the development and testing of the Cole-Bergman machine, and it was necessary to decide quickly what make of machine was best to install. The Callow pneumatic flotation process was recommended for installation in our concentrators for the following reasons: The results indicated: 1. That the Callow system made the highest extraction of copper values from the feed treated. 2. That the Callow system was simpler to operate and could he operated it a lower cost. 3. That the Callow system operated with a lower air pressure. (The question of the actual power consumption of the two types of machines was not definitely settled at this time.) During the official test period the Callow flotation apparatus showed an additional recovery of from 1 to 1.5 lb. of copper per ton more than the Cole-Bergman machine, this difference being maintained by further treatment of the tailing from both machines. The simplicity of the operation of the Callow flotation system is one of its notable features, two operators per shift being able to handle 90 standard cells and blower equipment.

Jan 7, 1917

By J. S. Carman

As with the slogans of Madison Avenue, catch words or phrases frequently become topical. Much is heard these days of the confrontation between governments of developing countries and international mining capital. In actual fact, sadly there are too few cases of anything as positive as confrontation because such an action at least signifies a dialogue which may begin badly but end up fruitfully. Instead we have in general a climate of indifference and fear with the mining companies of note marking off most of the developing world as being unsafe for investment. There is an unreal air to this damaging impasse. The common sense and objectivity which are prerequisites of positive action are lost in a swirling cloud of mythology, embraced largely by governments. Let us examine some of the dangerous misconceptions.

Jan 1, 1977

By J. A. Orr

The details connected with the mining and subsequent handling of Creighton ore were fully covered in a paper presented to the Institute in 1920. The following brief notes describe certain phases of the present practice and show wherein it differs from the practice at that time. These may be summarized under the following headings. (a) Recovery of pillars. (b) Drawing the ore. (c) Change from sub-level tramming to branch-raise system. (d) Chute construction. The present stoping practice is the same as formerly, i.e., fiat-backed shrinkage stopes of 60-foot width, between rib pillars of 15-foot width, extending from the footwall to the hanging-wall. Formerly, when these stopes were completed to the stopes above, they were drawn empty of broken ore, and the 15-foot rib pillars were caved into the stopes and drawn off through the same chutes as were used to draw the ore from the stopes.

Jan 1, 1926

By Henry M. Howe

(Cleveland Meeting, October, 1912.) Manuscript received Aug. 20, 1912. PROFESSOR RUFF'S most illuminating paper' describing his extremely valuable investigation of the carbon-iron equilibrium diagram assigns definite temperatures to certain very important lines in the diagram, viz.: the eutectic temperature EB (Fig. 1) and the " near-eutectic " temperature E'B', but without indicating clearly enough the reasoning which warrants these assignments. These temperatures are of such primary importance that it is well to indicate the apparent gaps in the reasoning, in the hope that they may be filled in. In his diagram, Fig. 1, the point X and the lines B'D'HI represent the experimental results reached by Ruff and Goecke; 2 AB, AEB, and SE represent the liquidus, the solidus, and the solubility of the carbon in solid austenite in the absence of graphite according to Gutowsky,3 AB being also in accordance with Spiecker's data;4 ,S'E' the solubility of carbon in solid austenite in the presence of graphite according to Ruer and Iljin; 5 GS the line A3 after Goerens and Meyer;6 I and EBC the true eutectic line as inferred by Prof. Ruff from Gutowsky's data. B'D' is the carbon content found in cast-iron which had apparently saturated itself with carbon in the presence of the graphite of the enclosing graphite crucibles in which the determinations were made. From its straightness and its sharp inflection near 6.67 per cent. of carbon, the carbon content of * Professor of Metallurgy in Columbia University. 1 Metallurgie, vol. viii., pp. 456 to 464 and 497 to 508 (1911). 2 Idem, vol. viii., pp. 417 to 421 (1911). 3 Idem, vol. vi., pp. 731 to 743 (1909). 4 Idem, vol. vi., p. 524 (Wüst) (1909). 5 Idem, vol. viii., pp. 97 to 101 (1911). 6 Idem, vol. vii., pp. 307 to 312 (1910).

Nov 1, 1912

By A. R. Chambers

At the 1924 Annual Meeting of the Institute, held in Toronto, the writer presented some notes on the occurrence of salt at Malagash, Nova Scotia, together with a few remarks on the uses of salt. The development of these salt mines has attracted considerable attention to the district, and it may be of interest at this time to call attention to some of the newer uses of salt, and to give a brief account of the genesis of the Maritime salines, As it is not proposed to treat the subject in technical detail, and the paper is written in a lighter vein than is usual in contributions to your Transactions, you will please overlook any variations from a strictly technical method of presentation. The world's supply of salt is obtained in three principal ways: (1) By flooding shallow areas, or pans, with sea water, allowing the water to evaporate naturally by the heat of the sun's rays, and collecting the residue of solid salt. This method is employed, for example, at Turks Island, B.W.I. (2) By mining the rock salt in its natural state, and preparing it for market by a grinding process. This is the method adopted at Malagash, which is the only place in Canada where salt is actually mined. (3) By drilling a hole into an underground salt deposit, forcing fresh water clown the hole, and, after it has become saturated with salt, pumping the brine to the surface and recovering the salt by evaporation. This is the method pursued by the Canadian Salt Company, the Dominion Salt Company, and other producers in Ontario.

Jan 1, 1929

By James McMahon

Although doubt has been expressed many times as to who first brought self-contained breathing apparatus to this side of the Atlantic, there is none whatever that the first organized station was established at Glace Bay, N .S., by the Dominion Coal Company, in 1907. This station was started with 20 sets of 1907 "Draeger" apparatus and all necessary station equipment and supplies. After the fire at No. 1 pit, Sydney Mines, in 1908, the Nova Scotia Steel Company installed 15 sets of "Draeger" and sup-plies, which were housed in a rescue car (a converted pull-man.) In 1909 or '10 a fire occurred at the Back Pit, Stellarton, where the apparatus from Glace Bay was used, and subsequently the Acadia Company erected a station and in-stalled 10 sets of "Securitas" apparatus. In 1912 the station at New Waterford was opened and equipped with "Draeger," and the same year the station at Springhill was built and equipped with the same type. Sometime during past years the Nova Scotia Steel Company acquired a couple of "Proto" machines, and after the explosion at the Allan shaft in 1918 the Acadia Coal Company added some "Gibbs" to their station. From this it will be seen that when the coal-fields were organized under the British Empire Steel Corporation the equipment was rather mixed, therefore steps were taken by the executive to stanardize the whole of the rescue and recovery work.

Jan 1, 1924

Difficulties were experienced in the identification of carbonate minerals intimately associated with iron oxides in the so called carbonate ore, which occurs at depth in the Iron Duke Orebody.Determination of refractive indices by examination under the microscope using the immersion method, together with inferred chemical composition indicates that dolomite and parankerite are common constituents. Histograms of the manganese and sulphur contents strongly suggest that manganese is associated with the carbonate minerals, and that the highest sulphur assays occur near the base of the carbonate body.From the present work it is concluded that refractive indices indicate only a very approximate composition for carbonates of the parankerite type.The different carbonate minerals occur in irregular zones.INTRODUCTIONThe Iron Duke deposit is situated in the southern portion of the South Middleback Range on Eyre Peninsula, S.A., 30 miles from Whyalla. (Fig. 1).Drilling at Iron Duke revealed a large body of so called carbonate ore, which was tested in detail at cross section 1000 ft. S by three diamond drill holes, DDH.57, 67 and 78. (Fig. 2)Most specimens of carbonate ore described below were obtained from DDH 67 and 78.GENERAL GEOLOGYThe South Middleback Range is composed of two parallel ridges trending north-south. The Iron Duke orebody is situated on the southern portion of the western ridge. (Fig.1) .The rocks of these ranges belong to the Middleback Group which rests on a gneiss complex. Their age is considered to be Middle Precambrian or late Archaean.

Jan 1, 1963

By Albert Sauveur

IN an important paper on The Critical Ranges of Pure Iron1 presented at the May, 1913, meeting of the Iron and Steel Institute, Professor Carpenter reports and illustrates the results obtained by him in determining the critical points of some very pure electrolytic iron sheet about 0.01 in. thick. The iron strip was rolled into the form of a cylinder 1; in. long and fn in. wide, weighing 42 g., the thermo-couple being inserted in a small hole in the center. The points Ac3 and Ar3 were readily detected, as well as the point Art, but the point Act was absent from every heating curve. The author concluded from this occurrence that the conception of A2 as an independent allotropic change must be abandoned. At the October, 1913, meeting of the American Institute of Mining Engineers, Dr. G. K. Burgess and J. J. Crowe read a paper on The Critical Ranges A2 and A3 of Pure Iron2 in which they described some extremely important experiments conducted by them at the Bureau of Standards, Washington, D. C. They tested Professor Carpenter's electrolytic iron and detected a sharp and well-defined absorption of heat corresponding to the point Act. Professor Carpenter's failure to detect this point is explained by them on the ground that unless the iron be in a single piece entirely surrounding and in contact with the thermo-couple junction, the thermo-couple will integrate the irregular progress of the heat through the sample and the curves will lose their sharpness. In discussing Messrs. Burgess and Crowe's paper, Professor Carpenter accepted this explanation as probably accounting for the absence of Act in his heating curves.

Jan 2, 1914

By A. Sauveur

In an important paper on The Critical Ranges of Pure Iron presented at May, 1913, meeting of the Iron and Steel Institute…

Jan 1, 1915

By E. W. Parker

THE anthracite region, from which there is produced annually about 80,000,000 tons, or approximately 15 per cent. of the total coal supply of the United States, has a combined area of a little less than 500 sq. mi. The total area occupied by the bituminous fields (including the sub-bituminous and lignite fields) is in the neighborhood of 400,000 sq. mi., so that 15 per cent. of the total output comes from this small area of only a little more than 0.1 per cent. of the coal-producing territory. of the United States. The productive anthracite area is divided into a series of basins or troughs, roughly parallel, extending. in a northeast-southwest direction through the. Counties

Jan 1, 1921

By Bain, Edgar C.

THE results are presented of an investigation to discover the fundamental atomic conditions existing in Corson's high-copper alloys hardenable by means of silicide solution and reprecipitation. The study attracted the writer because it offered a very convenient example of the general type of hardenable alloys exemplified by duralumin. Sykes' iron-tungsten and iron-molybdenum alloys and the hardenable lead-antimony. SUMMARY OF RESULTS AND CONCLUSIONS In brief, the investigation shows that very perfect crystallinity exists in the solid solutions prepared at high temperature to contain as much dissolved silicide as possible. The lattice parameter of copper is altered very little by the amount of cobalt, nickel or chromium, and silicon dissolved. The hardening by drawing at a temperature to initiate precipitation of excess silicon and metal produces a remarkable change in the atomistics of the solid solution. The old perfection of crystallinity in the solid solution is destroyed and the new atomic spacings are of variable magnitude even in one grain, and a condition in a measure resembling that found in martensite is observed. Were no particles whatever precipitated by the drawing action, still ample causes for hardness would be in evidence in the solid solution alone. The lack of plane continuity in the crystal grains would oppose slip in a very effective manner. Complete annealing restores the crystalline perfection in large measure. In these alloys even the most sensitive methods failed to reveal the characteristic pattern of the silicide precipitated by the anneal, but this was largely to be expected as the amount is relatively small.

Jan 1, 1927

By J. Mullins

Coal was first banked by the Dominion Coal Company, Limited, in 1898, near No. 2 Colliery, the same site as is presently used for that purpose. Though today there are banks at Glace Bay, Sydney, and Sydney Mines, these notes, except when otherwise desirable, will be confined to describing the practice as developed at the No. 2 Banking Station, Glace Bay, as being typical of methods obtaining at all sites. Storing The manner in which the coal was piled is illustrated diagrammatically in the accompanying sketch. A train of coal was brought on the main trestle, which extended the full length of the banking ground at a height of 22 to 39 feet above the natural surface, and dumped into bins which were integral with the trestle work. Chutes from these bins permitted the coal to be fed into 3-ton cars, which were horse drawn laterally on narrow gauge tracks laid about 10 ft. centres, to a maximum distance of 400ft. from the trestle. These cars were end-dump and as the pile extended laterally the narrow gauge tracks were lengthened by shorter or longer filling pieces, so that their ends were always kept at the brow of the bank. Much coal, however, had to be dumped directly on the tracks and hand trimmed to fill the valleys, and level off, between the tracks.

Jan 1, 1931

By J. M. Hartman

ONE of the most important subjects to the blast-furnace engineer is a thorough knowledge of the conditions affecting the temperature in the different portions of the furnace. All efforts to decrease the consumption of fuel and improve the working of the furnace must be based upon it, and I may, therefore, be permitted to place before you the results of my observations, and detail the conclusions to which they have led me. Tracing the thermic conditions from below upwards we have at the bottom of a blast furnace making No. 3 iron a temperature of 2900° F., which increases slightly to a point a little below the tuyeres. In the immediate vicinity of the tuyeres the temperature is somewhat lower, owing to the entering blast ; but a short distance above the tuyeres, where all the oxygen of the blast has been converted into carbonic acid, the highest temperature in the furnace must be attained. This carbonic acid is, however, almost as soon as formed, converted by the glowing coal into carbonic oxide, a process which absorbs heat, reduces the temperature, and provides the active agent for the reduction of the iron ores. In its ascent the hot carbonic oxide gradually parts with its heat, first melting the descending iron and earthy materials, which drop down to the hearth of the furnace. The limit of this zone of fusion is rather sharply defined, and the temperature above this zone suddenly decreases. In its further ascent the hot gas drives off the carbonic acid from the limestone, which causes a further absorption of heat, and finally the gas escapes at the top, at a temperature of about 250° F. if the furnace is working well. These changes of temperature 1 have attempted to represent graphically,

Jan 1, 1880