Search Documents

Numerical simulation of the fluid flow and heat transfer has been carried out for a waste-heat boiler in an Outokumpu type copper flash smelter. In this boiler, SO2-containing off-gas flows into the waste-heat boiler radiation section at about 1350°C. A fraction of cooler off-gas from the electrostatic precipitator at about 200°C was recirculated into the radiation section, and a small amount of ambient air was leaked into the boiler from the bottom. The computational results show that the flow is strongly recirculating and distinctly three dimensional in most of the boiler, particularly in the radiation section. The hot off-gas cooled down rapidly after entering the radiation section due to radiation. The predicted flow pattern and temperature distribution were in a good agreement with laboratory models and industrial measurements.

Jan 1, 1995

By Nan Wang

Based on the commercial computational fluid dynamics software, Fluent, the fluid flow and temperature field in an iron-bath reactor were simulated numerically, and the effects of top-blown and side-blown operating parameters on the mixing time of iron bath, distribution range of oxygen in top space, and post-combustion ratio were investigated. The simulated results showed that the mixing time of iron bath increased initially and then decreased with the increase of inclined degree and immersion depth of side-blown lance. The distribution range of oxygen became wider as pulling the top lance away from the iron bath. Furthermore, post-combustion ratio was reduced given the top lance was too close the bath. The simulation results provide theoretical base for the process optimization of iron-bath reactor and further development of new type iron-bath smelting reduction process.

Jan 1, 2009

By Bryan J. Travis, Thomas L. Cook

INTRODUCTION Our growing concern for adequate and secure sources of energy and minerals has stimulated vigorous exploration for new sources, research toward a better understanding of geological processes, and development of new extraction technologies. The need for control, or at least prediction, of subsurface fluid flow is important for many of these technologies for example: primary, secondary and tertiary recovery of oil; ground water and waste management; in-situ fossil energy extraction (oil shale, coal, tar sands); and solution mining of uranium, copper and other minerals. These technologies, especially the last two, are characterized by highly complex systems. A partial list of the physical processes occurring would include flow in porous/fractured media, multi-phase and multi-component flow with heat transport, chemically active fluids and soils, tracers, diffusion and dispersion, fracturing and dissolution. A great deal of understanding of how these processes behave and interact can be obtained from models. MODELS Theoretical models are valuable because they: 1) provide a frame of reference for interpreting results of laboratory and field experiments; 2) once validated by experiments, allow a variety of geometries, injection/production strategies, etc., to be examined (at relatively low cost) for efficiency and stability; 3) can provide guidance to the design of experiments and field operations. Most models are based on the fundamental principles of mass, momentum and energy balance. But from this starting point, many paths can be taken. For example, there is the theory of Payatakes (1973) which concentrates on the microscale dynamics. In this approach, the rock or soil matrix is represented by a complex of characteristic channels (such as periodically constricted smooth tubes). Detail of flow within the characteristic channel is calculated very accurately. A difficulty with this model is that description of a representative channel can require several parameters which may not be easily measured. Also, it is not clear how the channels can be combined practically to model a large scale flow. Another type of model is the "global" one described by Bear (1972). Here, the continuum equations for conservation of mass, momentum and energy are averaged over a distribution of pore channels, resulting in a set of conservation equations in which the small scale structure of the medium is replaced by quantities such as porosity, permeability, dispersion coefficients and tortuosity. This approach allows computation of large scale flows. However, additional constitutive equations are needed which relate averaged quantities such as permeability to observables such as local saturation, particle size distributions, and others. An important difference between models is the way they handle the momentum equation. Payatakes' model solves the full equation. In others, it is replaced by a simpler relation such as Darcy's law (valid for slow flow rates) or by Forchheimer's equation which extends Darcy's law to higher flow rates. These simple relations can nevertheless match a great deal of experimental data (Dullien 1975). The permeability term which appears in Darcy's law and in Forchheimer's expression has been related to other quantities such as porosity and particle surface area. The Kozeny-Carmen equation is a well-known example, valid for some ranges of porosity and particle sizes and for some materials. Several other semi-theoretical, semi-empirical formulations have been devised, none of which are entirely satisfactory. One goal of researchers has been the ability to predict permeability of a porous material from basic measurable quantities such as grain size distributions without recourse to adjustable parameters. This effort has proceeded from consideration of distributions of idealized, non-intersecting channels, to intersecting channels, to consideration of both distributed pore radii and pore neck radii. This last approach has been used successfully to predict permeabilities (ranging over several orders of magnitude) in sandstones (Dullien 1975). Additionally, studies on explicit networks of channels (e.g., Fatt 1956) and percolation theory (e.g., Larson et. al. 1981) have been used to examine interconnectivity effects in porous media with the hope of eventually being able to predict permeability accurately. To be of more than theoretical interest, a model must be compared s controlled laboratory conditions where boundary and initial conditions and relevant material properties can be accurately determined. Also, extraneous forces can be eliminated so that the interactions between processes of interest can be clearly seen and flow models can be vigorously tested. In contrast to the well-defined environment and

Jan 1, 1982

By Menglong Bian, Xiaotong Dong

Thermal damage is an urgent problem faced by deep mining. High-temperature rock mass, hot water and electromechanical equipment are the sources of the thermal damage. The increase in air temperature in mine tunnel is the result of fluid–solid coupling heat transfer from various heat sources. This paper takes a roadway with hot water and a mine car as the research object. Based on the Fluent, Static Structural and Steady-State Thermal modules in ANSYS, the thermal-fluid–structure coupling analysis in the roadway is carried out. It is found that the hot water has a significant effect on the thermal environment of the mine. Under the experimental parameters, the maximum heat flux density and equivalent elastic strain at the interface between the hot water and the rock are 9789.3 W/m2 and 0.00054532 m/m, respectively. The heat flux distribution in the rock area near the mine car does not change much, and the equivalent elastic strain value in this area is high. After the air is heated in the hot water area, the temperature curve changes gradually and then rises steadily. By changing the inlet air temperature parameter, it is found that the lower the inlet air temperature, the better the cooling effect, and the change of the inlet air temperature can change the air temperature field in the roadway as a whole. By changing the parameter of inlet air speed, it is found that higher wind speed brings better cooling effect, but with the increase in wind speed, the cooling effect of roadway thermal environment is very limited. When the wind speed increases from 5 m/s to 10 m/s, the air temperature of most measuring points drops by more than 2℃; when the wind speed increases from 15 m/s to 20 m/s, the air temperature of most measuring points drops below 0.7℃. After the wind speed reaches a certain value, the cooling effect of ventilation is very limited.

May 5, 2022

By M. K. Ameen, R. El-Hacha

This paper presents the analytical results obtained from numerical simulation of reinforced concrete slabs strengthened with various FRP systems and subjected to blast loading. A three-dimensional finite element model using AUTODYN software was used to predict the overall behavior of the slabs. The numerical results were validated by comparing with experimental results from a program carried out to investigate the efficiency of different strengthening systems on the blast resistance improvement of small-scale reinforced concrete (RC) slabs. The experimental program consisted of testing nine RC slabs strengthened with three different externally bonded (EB) FRP systems attached at the bottom side of the slabs and one RC slab tested without strengthening for comparison purposes. The EB FRP strengthening systems investigated included two layers of Carbon Fiber Reinforced Polymer (CFRP) sheets, two layers of Glass Fiber Reinforced Polymer (GFRP) sheets, and one layer of Glass-Fiber Resin Polymer (GRP) sheet. Different epoxy resin, patching mortars and impregnating epoxy adhesives were used for the slab surface preparation and FRP system application of the strengthening layers. The aim was to evaluate the residual strength of the test specimens after exposure to blast loads. The blast loading parameters were evaluated for each test using AUTODYN simulation and compared with the computer program CONWEP. All specimens were subjected to same spherical TNT charge weight and stand-off distance with the respect to the slab top surface. Extensive comparison is made between the experimental results and the AUTODYN simulations for the control unstrengthened slab and the strengthened slabs including time history records of the bottom steel strain and mid-span acceleration and the peak dynamic deflection of the slabs.

Jan 1, 2010

By Y. Jin, H. You, H. Pang, B. Lin

Successful application of steam assisted gravity drainage (SAGD) on the recovery of land facies ultra-heavy oil in Xinjiang oilfield depends largely on shortening the preheating period with the aid of the micro-fracturing technology, which is conducted through controlled water injection to a pair of horizontal wells to create homogenously distributed microcracks in the zone between the two wells. The numerical simulation of this mechanical process is yet to be investigated. Up to date, there has been research work on rock mechanics during the SAGD production period of marine deposited ultra-heavy oilsands, but the counterpart research on land facies ultra-heavy oilsands of Xinjiang oilfield is left undone. In this regard, this study is attempted to perform numerical simulation of the fracturing process on land facies unconsolidated oilsands. With this objective, the study first investigates geological and physical identification of the field collected cores, then carries out mechanical analysis on laboratory triaixal test results, based on which numerical simulation of the fractured zone is performed. The simulation is applied through a finite element platform adopting extended Drucker-Prager constitutive model, with the parameters determined by experimental work. It is verified that hydraulic fracturing of unconsolidated oilsands generates a microcrack feature in terms of a dilative zone instead of linear apertures. The extent to which the fractured zone propagates is visually demonstrated based on the magnitude distribution of equivalent plastic strain or volumetric dilation. Evaluation of the connection of injection and production wells can possibly be determined by the expansion of the saturated region around each well. Finally, the implications on the efficiency of hydraulic fracturing in stimulation of the pay zone are investigated.

Jan 1, 2015

By Yuting Xue, Danqing Gao, Brijes Mishra

Heterogeneity and discontinuity significantly affect rock strength. For accurate stability prediction, intact rock behavior is imperatively included in rock mass behavior. However, past research largely used arbitrary scaling approaches to produce rock strength. This paper considers a stochastic approach in order to determine the strength of a rock. Based on the laboratory data, a MATLAB® with extreme value stochastic model generates a database for each physico-mechanical property. Then FLAC® simulates laboratory-sized rock specimens. The grids developed in the numerical model can in turn develop random material properties in MATLAB®, which researchers then applied to the final FLAC® model. Model runs simulate the approach performed in the laboratory. The results from the model indicate that a stochastic approach produces strengths that are lower than a deterministic approach. Failure modes for each specimen are different, similar to observations in the laboratory. In addition, random density also influences the failure mode, highlighting the importance of stochastic analysis in rocks.

By Cheng Li, Yanlei Wang, Lingrui Kong, Jianxin Tang, Fang Yuan

Coal mined-out areas have a significant impact on mining safety and affect the pressure distributions of neighboring coal faces. The PFC3D software is used to study the goaf mechanical characteristics, and the core loading test verifies the rationality of the numerical simulation method. The results from the numerical modeling showed that the void ratio, particle size ratio, and particle size distribution of the rock particle sample (RPS) had a significantly remarkable influence on the compression deformation characteristics of the rock block. The parallel-bond tensile strength and parallel-bond cohesion had a notable impact on the compression deformation traits of the rock block only when the axial stress level was lower than 12 MPa. By contrast, when the axial stress exceeded 5 MPa, the effective modulus significantly influenced the compression deformation features. However, the stiffness ratio, loading rate, and parallel-bond friction angle had almost no effect on the compression deformation characteristics. Furthermore, when the stress level was less than 10 MPa, the stress–strain curves from the rock core samples’ numerical simulation and loading tests were approximately linear. In addition, the Pearson correlation coefficients of the stress–strain curves suggest that the goaf zone’s core numerical simulation results had a robust correlation with the loading test results. The findings of this study can serve as a reference for the field application of PFC3D software and safety assessments in goaves.

Jan 18, 2022

By Hwasoo Park

Keywords: FC mold, Argon, Magnetic, Solidification Fluid flow plays a significant role for steel surface quality in continuous casting. Although water models are able to model fluid flow, the flow pattern is not of practical interest since the moving solidifying shell cannot be accounted. Computer modeling has become a popular and dependable tool to analyze the complex phenomena occurring in continuous casting. In this numerical simulation we coupled momentum and energy equations considering the solidification of steel along with turbulence ?-e model. The vertical bending mold is equipped with bifurcated nozzle with 15 degrees of port angle. FC mold is supplied with DC induced magnetic fields. Influence of argon and magnetic fields on molten steel flow and heat transfer is investigated by solving momentum equations adding source terms due to multiphase ? magneto hydrodynamics. The results show that magnetic fields reduce the jet velocity from port by lower magnetic core induced field but the influence on meniscus velocity is complex to describe. Magnetic fields increase surface temperature and homogenize its distribution on surface and inside a mold.

Jan 1, 2005

By Guo Wenbing

"INTRODUCTIONThere is a great amount of coal (about 140 billions tons) left unmined under the surface structures, water bodies, railways (referred to as the “three-body”). Coal mining under “threebody” especially that under surface structures has become a major problem in the mining area. The key problem of mining under surface structures is to control overburden strata and surface movements. At present, the major surface subsidence control methods are strip pillar mining, backfilling mining method, room and pillar mining, grouting of bed separations, harmonic mining, and so on. Wongawilli mining method is a high-efficient shortwall mining method developed based on the room and pillar mining, and named after the first successful trial in Australia “Wongawilli” coal seam. The room and pillar mining equipment such as continuous miner is employed in this method. Its major advantage is flexible face layout. It can be used to mine the small wedge coal blocks and those that are difficult to be mined with retreat longwall mining method. It requires less capital investment, short lead time for production, flexible equipment operation and face move and high productivity. It has been applied in some China’s coal mines.The “Wongawilli strip coal mining technology” is a new coal mining method for mining under surface structures. It combines the strip mining longwall layout and Wongawilli high efficient mining technology. This technology can fully utilize the advantages of both the strip pillar and Wongawilli mining methods, and overcomes the disadvantages such as frequent face move, and low mining efficiency in strip pillar mining, and poor ventilation condition and poor long-term stability problems of coal pillars. In this paper, the Wongawilli strip mining method was designed for Wangtaipu mine and its feasibility was studied using numerical modeling and surface subsidence prediction.Geological and mining conditionsAt present, most of the No.15 coal seam reserves totaling 377.07 million tons in Wangtaipu mine are located under surface structures. In order to mine the coal under the surface structures, the Wongawilli strip mining method was employed. An appropriate panel was selected for trial and the surface movement monitoring lines were set up. The trial area is located in panel XV2214 (East) ( re 1). In this area, the floor elevation of coal seam is +634~646m, the surface elevation is +810~817.5m, and the average depth of coal seam is about 174m.The average panel length is 282m and average panel width is 73.5m. The seam dips 1~3° and is 1.8~2.5m thick with an average of 2.15m. The roof and floor rock characteristics are shown in Table 1."

Jan 1, 2015

By T. G. Sitharam, Resmi Sebastian

"Wave propagation studies across jointed rocks have significance in the fields of rock mechanics and geophysics. The passage of a seismic wave induces strains in rocks and often, these strains are of low magnitudes except at the vicinity of source. These low magnitude strains are generally in the elastic range and hence elastic constants necessary for the design and analysis of strength of rock mass, can be derived from wave velocities. Measurement of travel time velocities and measurement of resonance frequencies are the two methods usually adopted for obtaining wave propagation velocities.Resonant column apparatus measures wave velocities from the resonant frequencies obtained during testing. Depending on the type vibration applied, torsional or flexural, shear and compression wave velocities are secured. By varying the amplitude of vibrations applied, various strain levels can be introduced and corresponding resonant frequencies and wave velocities can be calculated. The resonant column experiments were performed on a model material, hardened Plaster of Paris (POP) samples, in laboratory. The paper explains the preparation of samples and the working mechanism of resonant column apparatus along with the estimation of wave velocity from resonant frequency. The numerical simulation of resonant column apparatus using distinct element method and its validation with the experimental results are presented in the paper.A distinct element code is usually used to simulate the movement of materials with intersecting discontinuities. Finite rotations and displacements of individual blocks representing the material are permitted and new contacts between the blocks are identified as the calculation progresses. Three dimensional Distinct Element Code (3DEC), the software intended for the numerical simulation of rock engineering projects, can well simulate the behavior of jointed rocks under static and dynamic loading conditions. The numerical simulation of resonant column apparatus has been performed with 3DEC considering its efficiency in modeling jointed rocks.The numerical modeling of the resonant column apparatus with application of torsional and flexural vibrations to the sample is elaborated in the paper. The response of samples to a range of frequencies is obtained and the frequency that induces maximum displacement in the sample is measured as the resonant frequency, for any particular strain level. The displacements measured at various points of the sample during application of vibrations are compared and presented. The numerical modeling of resonant column apparatus with an intact sample (without joint) and a sample with a joint incorporated are explained at a particular strain level. The resonant frequencies obtained from laboratory experiments and numerical simulations are compared and illustrated. It has been found that resonant frequencies obtained using numerical and laboratory experiments are in good comparison and can be extended for various strain levels and sample conditions."

Jan 1, 2015

"A numerical procedure based on Smoothed Particle Hydrodynamics (SPH) is developed for rock blasting phenomena involving multiple intersecting joints. In this procedure, an elasto-plastic damage constitutive model has been applied in the framework of SPH to simulate yielding response of the surrounding rock medium. In this paper, a square shape rock medium with centrally located emulsion explosive in a borehole is numerically blasted with and without the presence of two diagonal rock joints. The model is simulated by assuming all four sides of the rock medium as free surfaces. The paper elaborates the propagation of stress wave, expansion dynamics of gaseous products, and development of fracture, fragmentation of the medium and dissipation of energy due to damage.INTRODUCTIONDamage prediction of rock mass and its mean fragmentation size are of important to design blast parameters for a given explosive. Current blasting practice solely depends on empirical relationships between fragmentation sizes to those blast design parameters while mathematical descriptions of the physical laws governing the process of rock blasting are limited. A constitutive relationship based on properties of explosives and rock mass is of special interest because of its capabilities in describing the key features of rock fracture and fragmentation, resulting in understanding of the physical process involved in rock blasting. It is well known that blast-induced damage and fragmentation of rock mass occur due to detonation induced stress wave and product gas driven fracture propagation. Nevertheless, the fundamental mechanism of the failure process and the behavior of rock characteristics under these two different loading are not well understood in many cases, which are closely related to growth of fractures and interaction of cracks under different loading conditions.Continuum damage mechanics is considered to be appropriate to describe the failure process under such high-amplitude stress wave. Based on this approach, several theoretical models have been developed to analyze the dynamic damage of brittle material such as rock and concrete with microstructure (Chen, 1999; Taylor et al., 1986; Wu et al., 2004; Yazdchi et al., 1996). These models are mostly based on the theory of damage mechanics or fracture mechanics with some statistical treatment to incorporate random distribution of microcracks. In the application of fracture mechanics theory, sometimes it is difficult to estimate the micromechanical parameters such as crack density and fracture toughness in different modes. In this study, damage in rock material is evaluated according to the earlier model developed by Grady and Kipp (1980), which is a fracture model coupled with a material description for stress wave propagation to predict quantitatively fracture and fragmentation under explosive loading conditions."

Jan 1, 2015

By B. Panton, J. Carvalho, E. T. Brown

"A major consideration in the design of high capacity tiedown anchors for dam, bridge and tower foundations is the tensile resistance of the rock mass to pullout, typically as a result of overturning moments or hydrostatic uplift. Rock mass pullout capacity for installed anchors is developed from the tensile strength and fracture propagation properties of intact rock, the orientation and physical properties of the discontinuities and anchor confinement at depth. The typically assumed, but generally conservative, design approach is to calculate anchor pullout capacity using the dead weight of a uniformly shaped inverted “cone” with an assumed initiation point and breakout angle. In some cases, some tensile or shear strength is considered across the area of the assumed pullout cone, however, these strength estimates are based primarily on based on limited historic testing data, empirical relationships for rock mass strength developed for other applications, and engineering judgement.As an alternative to the current foundation anchor design method, this paper presents a new approach to the rock cone pullout problem using Discrete Fracture Networks (DFN) combined with numerical simulations. The simulations presented in the paper investigate the influence of fractures in a synthetic rock mass on ultimate anchor strength. In addition, the global influence on fracture network statistics on rock mass pullout failure is also discussed and it is contended that some of the aleatory and epistemic uncertainty inherent in the design of rock anchors can be reduced by considering fracture statistics in anchor design."

Jan 1, 2015

By A. J. Basu

Rock mass properties testing for determining strength parameters is an integral part of geomechanics. These tests are performed either in a laboratory environment or in a field (in-situ). The authors share their experience in using numerical modelling in simulating the laboratory test procedures. This approach helps studying the rock breakage and failure mechanism more efficiently and provides a high degree of visualization. Moreover, imperfections and discontinuities can be easily incorporated in these models. This capability of providing arbitrary fractures and discontinuities facilitates in building a large knowledgebase of rock strength and failure mechanisms. This knowledgebase may then be used to generate heuristics for determining rock strengths for rock mass with fractures and discontinuities.

Jan 1, 1997

By D. P. Roberts

This investigation aimed to simulate the experiments performed by Nic Gay (Gay, N.C.1976. Fracture growth around openings in large blocks of rock subjected to uniaxial and biaxial compression. International journal of Rock Mechanics and Minining Sciences and Geomechical Abstracts, vol. 13. pp. 231-243) on fracture growth around openings in blocks of rock subjected to uniaxial and biaxial compression, using the Elfen discrete element code. The results of the physical experiments indicated a number of trends that were successfully replicated in the numerical simulations, including crushing ahead of the face, the formation of a sub-vertical tensile fracture at centre-span, the formation of groups of fractures originating from the crushed face zone, the formation of large corner-to-corner fractures which precede sample failure, and linking of slot corner and sample corner fractures leading to sample failure. In addition, other features were apparent that were not reported by Gay. It is believed that these took the form of conjugate shear fractures (as reported by Gay in a previous paper) and other features that may have been altered or inhibited by the presence of pre-existing structure in the physical samples. It was found that the samples, though nominally made up of the same rock type, must have had significantly differing properties. The presence of pre-existing structures may have contributed to this discrepancy. Strain measurements from the physical experiments were reasonably well matched, except where the gauge lay directly in the path of advancing fractures.

Jan 1, 2012

By M. Kilfoil

Many minerals processing operations result in crushed rock being mixed with a liquid. Sometimes, the rock particles have to be dried before the next process begins and there may be a considerable distance between the equipment carrying out these processes. Bateman Engineered Technologies (BET) developed, patented and commercialized a method of simultaneous pneumatic conveying and drying. A joint project to assist with optimizing the process is under-way. Part of it is a numerical simulation of the process. The simulation is done using a dedicated program written in MATLAB, (commercial software which is widely used in engineering). It accounts for heat and mass transfer as well as particle transport. The main part of the program consists of a loop containing a series of equations which are evaluated sequentially. During any particular iteration, the properties are changed one at a time. Since the properties are changing relatively slowly, this method gives good results. The outputs of the simulation are consistent with the operational experience of BET’s engineers. The output is very comprehensive and all numerical. Since the program is currently being used for research purposes, flexibility is very important. Thus the output is converted into a spreadsheet file. Variations in the output quantities are displayed graphically using MS Excel. Some simulation could have been done using computational fluid dynamics (CFD) software. The advantages and disadvantages (technical, financial and skills requirements) of the two approaches for this particular type of simulation are compared briefly. Keywords: Pneumatic conveying, Heat and mass transfer, Computer model

Jan 1, 2003

By Bernhard Hiebl

Global trends that are constantly challenging the iron and steel producers are related to worsening of the iron ore grades, higher substitution rates of main iron ores to cheaper raw materials due to economic pressure and increased environmental standards. Changing the raw materials in an operating plant can significantly influence the sintering or pelletizing process. Adjusting all process parameters to regain stable and high productive operation takes considerable time and causes production losses. Furthermore changes in raw materials lead to variations in the process gas flows and emission concentrations.Therefore SVAI developed two models for numerical simulation of sintering process and pelletizing process. Amongst others the models are based on Ergun equation and include chemical reactions of the related process. For already operating plants the simulations shall predict changes of the process parameters when raw materials are exchanged or when operational parameters are varied. Furthermore the simulations give advantageous information for the design of green field plants and allow the simulation of different plant configurations.The objective of this paper is to demonstrate what the latest developments are in these numerical simulations and what Siemens VAI is doing to overcome the remaining challenges in this field.

Aug 2, 2018

By Li. Jiarong, Zuojian Liang, Qingyan Xu, Baicheng Liu, Shizhong Liu, Hailong Yuan

Single crystal solidification of turbine blades is a key technology for the production of reliable and high efficiency gas turbines. The solidification process of single crystal investment castings causes a number of problems that have to be solved such as the increase of casting defects and complexity of production process. Computer modeling and simulation is helpful to predict the defects and improve the process design. In the paper, a mathematical model for three dimensional simulation of solidification and single crystal growth of investment castings was developed based on CA, mechanism of crystal growth and basic transfer equations such as heat, mass transfer equations. Many factors including constitutional undercooling, curvature undercooling and anisotropy, which had vital influences on microstructure evolution, were considered in the model. Temperature, crystal growth interface and structure defects of investment castings of single crystal superalloy were investigated at withdrawal rates of 4.5mm/min and 7mm/min. Simulated results showed that microstructure evolution and structure defects were predicted reasonably and calculated results were coincident with experimental ones. The study indicated that three dimensional solidification simulation technique is a powerful tool for understanding the fundamental of solidification and the formation of structure defects in single crystal investment castings and finally for optimizing process design.

Jan 1, 2004

By Min Chen

A numerical simulation of the stress field of the solidified shell in the mold during continuous casting of peritectic steel slab was calculated with commercial software. The results showed that the maximal stress on wide face of the solidified shell was located at the corner and near middle of the slab, and it increased with increasing the width of slab. In addition, the stress was also influenced by operating parameters such as superheat degree, drawing speed and cooling intensity of the mold, and the maximal stress value and its position changed with these parameters. For the slab with section size of 3200mm×150mm, the proper drawing speed was around 1.2m/min, with cooling intensity of 5500L/min while the superheat degree was 15°C to 25°C in order to prevent longitudinal crack occurring during peritectic steel continuous casting.

Jan 1, 2009

By Huimin Lu, Lian Zhou, Qiang Li

"A three-dimensional mathematical model is developed for the regenerative rotary hearth furnace with 40 meters medium diameter. The influence of combustion switchover and outlet pressure on the fluctuation and distribution of temperature and pressure is studied with numerical simulation method. The results showed that the temperature field and flow field is suitable for requirement of industrial production; the fluctuation of the temperature field and pressure is acceptable; the influence of outlet pressure on the furnace pressure is great.IntroduceRotary hearth furnace which is originally utilized as heat treating and reheating industrial furnace, now is also used for carbon based DRl production. With the need of market and the concern of resource recycling and environmental issues, the DRl production from ore or from waste material by rotary hearth furnace attracts more and more attentions from steel industry [1,2].When rotary hearth furnace works, the feed pellets are charged on the hearth and rotate within an annular furnace chamber with the process of reduction. For the sake of rapid reduction, usually the depth of the pellet is one or two layers, accounting for less than 90% of the volume of furnace. As result, the exhaust gases carry away a lot of heat, so that energy utilization efficient is low [3]. Currently, in order to reduce the consumption of energy and improve the production efficiency, many methods have been adopted. The regenerative combustion technology is one of the most promising."

Jan 1, 2013