Search Documents

By D. R. Conlon, E. R. Brownscombe

Errors in measurement of reservoir pressure include: (I) gauge errors, and (a) interpretation errors. Gauge errors may be reduced by: (a) reading charts with a comparator microscope, (b) use of hard metal stylus points to give clear lines, (6) insuring temperature equilibrium, and (d) making multiple tests. Check calibrations are equally as important as check well tests. A statistical analysis of such check runs shows quantitatively the advantages of a standardized "zero pressure line'' and of the use of field calibrations made at bottom-hole temperature on the same chart run in the well. Interpretation errors include: (a) fluid heads, which should be corrected to the top of the perforations on the basis of well-fluid gravity and from the top of the perforation to the datum level on the basis of reservoir-fluid gravity, and (b) gradients around the well. Conventional shut-in periods may be entirely inadequate to overcome these, necessitating a reservoir study based on build-up curve data, reservoir history, core analysis and any other available information. Interest in engineering studies of the pressure changes in oil and gas reservoirs is increasing. This type of work yields important information and doubtless will be greatly extended in the future. One of the factors limiting the work, however, is the accuracy with which the reservoir pressures can be determined; for if the inaccuracies in the pressure measurements represent an appreciable percentage of the pressure changes, the engineer is seriously handicapped, and must delay the reservoir study until the reservoir pressure has changed a relatively large amount. This delay can greatly reduce the benefits of such studies, at least from the point of view of aiding the leasing, drilling and completion programs. Thus, from the point of view of reservoir analysis, it is frequently important to obtain the most accurate pressure data possible early in the history of any field—particularly for the gas-distillate fields now being developed. This paper deals with improvements in the measurement of bottom-hole pressures that permit pressures even as high as 4000 or 5000 lb. per sq. in. to be determined with gauge errors of only+ ±I to 2 lb. per sq. in. Since pressures out in the reservoir rather than in the bottom of the hole concern the reservoir analyst, differences between bottom-hole pressures and actual reservoir pressures are also considered. In general, errors in pressure measurement may be divided into: 1. Gauge errors: a. Errors due to inaccuracies in reading the pressure charts. b. Errors due to irreproducibility of the pressure element and recording system. c. Errors caused by failure to allow the gauge to reach temperature equilibrium. 2. Internretation errors: a. Errors caused by a fluid head between the gauge position in tubing and the pressure at the datum level in the reservoir. b. Pressure gradients in the reservoir.

Jan 1, 1946

By D. R. Conlon, E. R. Brownscombe

Errors in measurement of reservoir pressure include: (I) gauge errors, and (a) interpretation errors. Gauge errors may be reduced by: (a) reading charts with a comparator microscope, (b) use of hard metal stylus points to give clear lines, (6) insuring temperature equilibrium, and (d) making multiple tests. Check calibrations are equally as important as check well tests. A statistical analysis of such check runs shows quantitatively the advantages of a standardized "zero pressure line'' and of the use of field calibrations made at bottom-hole temperature on the same chart run in the well. Interpretation errors include: (a) fluid heads, which should be corrected to the top of the perforations on the basis of well-fluid gravity and from the top of the perforation to the datum level on the basis of reservoir-fluid gravity, and (b) gradients around the well. Conventional shut-in periods may be entirely inadequate to overcome these, necessitating a reservoir study based on build-up curve data, reservoir history, core analysis and any other available information. Interest in engineering studies of the pressure changes in oil and gas reservoirs is increasing. This type of work yields important information and doubtless will be greatly extended in the future. One of the factors limiting the work, however, is the accuracy with which the reservoir pressures can be determined; for if the inaccuracies in the pressure measurements represent an appreciable percentage of the pressure changes, the engineer is seriously handicapped, and must delay the reservoir study until the reservoir pressure has changed a relatively large amount. This delay can greatly reduce the benefits of such studies, at least from the point of view of aiding the leasing, drilling and completion programs. Thus, from the point of view of reservoir analysis, it is frequently important to obtain the most accurate pressure data possible early in the history of any field—particularly for the gas-distillate fields now being developed. This paper deals with improvements in the measurement of bottom-hole pressures that permit pressures even as high as 4000 or 5000 lb. per sq. in. to be determined with gauge errors of only+ ±I to 2 lb. per sq. in. Since pressures out in the reservoir rather than in the bottom of the hole concern the reservoir analyst, differences between bottom-hole pressures and actual reservoir pressures are also considered. In general, errors in pressure measurement may be divided into: 1. Gauge errors: a. Errors due to inaccuracies in reading the pressure charts. b. Errors due to irreproducibility of the pressure element and recording system. c. Errors caused by failure to allow the gauge to reach temperature equilibrium. 2. Internretation errors: a. Errors caused by a fluid head between the gauge position in tubing and the pressure at the datum level in the reservoir. b. Pressure gradients in the reservoir.

Jan 1, 1946

By William E. Schoeneck

This paper presents the problem of oil-well abandonment as a group of studies involving the compilation of physical well data, the use of special curves, maps, and interpretative Procedures, in order that operations can be analyzed and means for reducing costs can be effected. Methods for the calculation of the economic limit of production and resultant oil reserves are suggested in order that profitable production may be continued and premature abandonment prevented. INTRODUCTION Purpose Extensive studies have been made and much has been written on the procedures for prospecting, drilling, completion, production and repair of oil wells, but the writer has long felt the need for a study of the procedure that should be followed when considering the abandonment of a well. The production from numerous well bores of a fluid material (a circumstance peculiar to the oil industry) that is continually decreasing in quantity leads to an increasing ratio of operating cost to production. It is for this reason that oil fields are not abandoned as a whole and detailed consideration of each well is required before it can be determined whether more is being expended than will be returned On any well or lease in question. It is the purpose of this paper, therefore, to compile, correlate, and present all matters worthy of consideration in the problem of oil-well abandonment; to suggest interpretative procedures based on such compilations, to the end that reliable estimates of reserves and life may be obtained; to show, as a result of such interpretative procedures, the possibilities for corrective measures conducive to economical production, thereby extending both profitable reserves and length of life. Scope and Approach Compiling data and outlining a study having the complexity of the problem at hand are naturally subject to the personal experiences of one who undertakes the study; however, the chosen approach and grouping of the subject material may be helpful in the consideration of abandonment problems. Consideration has been given to wells that make gas and water incident with the production of oil; but consideration has not been given to either gas wells or condensate-producing wells, for wells of the latter type have sufficient problems to warrant separate investigation. The major subdivisions of this paper-— physical considerations and economic considerations—do not imply that either of these phases can be considered independently, but rather that the two are mutually dependent and are the component parts of an engineering study.

Jan 1, 1946

By William E. Schoeneck

This paper presents the problem of oil-well abandonment as a group of studies involving the compilation of physical well data, the use of special curves, maps, and interpretative Procedures, in order that operations can be analyzed and means for reducing costs can be effected. Methods for the calculation of the economic limit of production and resultant oil reserves are suggested in order that profitable production may be continued and premature abandonment prevented. INTRODUCTION Purpose Extensive studies have been made and much has been written on the procedures for prospecting, drilling, completion, production and repair of oil wells, but the writer has long felt the need for a study of the procedure that should be followed when considering the abandonment of a well. The production from numerous well bores of a fluid material (a circumstance peculiar to the oil industry) that is continually decreasing in quantity leads to an increasing ratio of operating cost to production. It is for this reason that oil fields are not abandoned as a whole and detailed consideration of each well is required before it can be determined whether more is being expended than will be returned On any well or lease in question. It is the purpose of this paper, therefore, to compile, correlate, and present all matters worthy of consideration in the problem of oil-well abandonment; to suggest interpretative procedures based on such compilations, to the end that reliable estimates of reserves and life may be obtained; to show, as a result of such interpretative procedures, the possibilities for corrective measures conducive to economical production, thereby extending both profitable reserves and length of life. Scope and Approach Compiling data and outlining a study having the complexity of the problem at hand are naturally subject to the personal experiences of one who undertakes the study; however, the chosen approach and grouping of the subject material may be helpful in the consideration of abandonment problems. Consideration has been given to wells that make gas and water incident with the production of oil; but consideration has not been given to either gas wells or condensate-producing wells, for wells of the latter type have sufficient problems to warrant separate investigation. The major subdivisions of this paper-— physical considerations and economic considerations—do not imply that either of these phases can be considered independently, but rather that the two are mutually dependent and are the component parts of an engineering study.

Jan 1, 1946

By B. C. Craft, T. J. Johnson, H. L. Kirkpatrick

Petroleum engineers are displaying considerable interest in the problems of cementing oil wells, especially in the Gulf Coast and California areas, where steep temperature gradients are encountered and where wells are being drilled to greater depths. Deep drilling, that is, at depths in excess of 7000 ft., has been undertaken in these areas only in the last few years and with this trend oil-well cementing requires more technical treatment. It is not the purpose of this paper to describe the scope and application of cement operations in the oil industry or to give the standard specifications, methods of sampling and testing of portland cement. The various testing methods have been described by the American Society for Testing Materials1, Uren2, Tickell and Wankowski3 and Rakestraw and Parsons4. The latter authors (pp. 50-58) have also described in detail the methods of cementing. The authors realize that it is impossible to reproduce in the laboratory the scale of forces and dimensions that exist at great depths, but an attempt has been made to scale down these dimensions proportionally. The selection of problems to be studied was based largely upon the practical questions asked by several of the largest operators in these fields. All cements used in these experiments met the specifications of the American Society for Testing Materials.

Jan 1, 1935

By James B. Graham, Earle E. Smith

The value of all minerals produced in the United States for the years 1930 to 1932 averaged $3,460,000,000 annually, according to Bureau of Mines reports. Of this amount, approximately $1,280,000,000 represents nonmetallic substances, such as petroleum, gas, sulfur and salt produced as fluids. Thus, about.37 per cent of the country's mineral wealth is procured through wells drilled in the earth, which require casing to keep them open throughout their life. Deep well drilling has increased greatly in the last few years. Several strings of casing have been set deeper than 9000 ft.—one, a string of 7?-in. O.D. casing, 10,301 ft. long, run in a well drilled by the Gulf Production Co. in West Texas, holds the record up to this time. These are longer strings than were contemplated when the American Petroleum Institute Specifications were adopted 10 years ago, therefore it is necessary to consider whether the present joint standards are adequate for such strings, or for even longer strings that may be called for in the future. Petroleum engineers are asking: Is there a possibility that stronger joints can be designed without going to stronger and more costly steels than offered in present specifications? Without sacrificing too greatly the tensile properties of the joint, can its design be changed to allow more clearance in the open hole below the next larger string of casing, and thus avoid costly underreaming? What can manufacturers offer for drilling through heaving shale? Fundamentals of the Problem During the last few years considerable study has been given to casing joints and their limitations, and since attention must be given to this subject by those who will be required to drill deeper holes, it is timely to review the fundamentals of the problem. These will be recognized generally as the following: 1. No threaded joint can be stronger than the area of metal under the root of the first perfect thread, and this area must be large enough

Jan 1, 1935

By C. W. Gibbs, E. K. Parks

In 1929 the Standard Oil Company of California commenced the development of a device for obtaining temperatures and pressures in flowing and shut-in wells and of suitable running equipment for such a recorder. Although simple in principle, the recorder has required much experimental work in its development. The various problems have now been solved to such an extent that it is believed that the apparatus affords a sturdy and reliable means for obtaining information regarding depth pressures,—apparatus that may be turned over to a well gang for routine operation. As an example of the rough usage the device will withstand a recent incident may be cited. Owing to failure of the lowering line at the conclusion of a run a recorder was dropped some 6300 ft. through 2 1/2-in. tubing filled with gassy oil. The device was fished out undamaged and with the pressure record intact, although the instrument had been subjected to a pressure greater than 2300 lb. per sq. in. for some 24 hr. after impact at bottom. Description of Recorder The instrument is of the continuous recording loaded spring type (Fig. I). Temperature is not recorded continuously but is obtained by maximum recording thermometers in an auxiliary thermometer well. The entire instrument assembly, from bottom of the recorder to top of the socket, is 6 1/2 ft. long and weighs less than 25 lb. The maximum outside diameter of the recorder shell is 1 1/4in., and all attachments need be no larger. This permits lowering the device inside 2-in. tubing. The operating principle is simple. The well pressure acts upon a piston A resisted by the extension of spring B. The spring deflection is recorded by a stylus C upon paper within the recording drum D. Springs.—To improve accuracy at lower maximum well pressures five interchangeable spring assemblies are used. These have maximum pressure ranges of from 250 to 5000 lb. per sq. in. Piston diameter is the same in all cases, and each spring is designed for a deflection of about 5 in. for maximum pressure loading. A complete spring assembly there-

Jan 1, 1934

By W. K. Lewis

During the last decade the petroleum refinery engineer has made great progress in achieving a better understanding of the physical behavior of hydrocarbon mixtures, with particular reference to their pressure-temperature-volume relationships, the mechanism of the evaporation of liquids, the condensation of vapors, including the changes in composition, and the heat effects accompanying them. With the new insight into the mechanism of movement of oil and gas through the formations in which they occur, achieved by the production engineer, it is clear that the latter will need to utilize in the solution of his own problems much of the information outlined above. It is the purpose of this paper to outline the portions of that information that seem most certain to prove of importance in production work. Properties of Pure Hydrocarbons While it is true that petroleum always consists of highly complex mixtures of hydrocarbons, none the less understanding of the behavior of the mixture must be based upon a knowledge of the properties of the pure components. However, in view of the tremendous number of hydrocarbons existing in petroleum, the determination and formulation of the properties of all of them would seem a discouraging task. The difficulty of the situation is increased by the undoubted facts that the overwhelming majority of chemical individuals in petroleum have never been isolated as pure compounds, none of their physical properties have been determined and even their chemical constitution is unknown. The situation would be hopeless were it not for the fact that certain extraordinary correlations of important properties of various hydrocarbons have been discovered which make it possible to predict those properties for a given chemical individual on the basis of a very limited characterization of it. Thus one can predict the vapor-pressure curve of an unknown hydrocarbon over a considerable range from the knowledge of a

Jan 1, 1934

By Walter Miller

Any annual review of engineering progress in petroleum refining must of necessity include many features mentioned in earlier reviews. Advances do not spring mushroom fashion to wide acceptance overnight, but rather resemble rolling snowballs, gathering size and velocity as they progress. The new ideas of one year develop through the course of scattered adoption and testing during following years, to be ultimately discarded or to become an integral part of refinery engineering and operation. Polymerization and Cracking As an illustration, the publicity given to the polymerization and cracking of petroleum gases during the year has given many the impression that this is a new art. But patent and technical literature have disclosed active work on the problem dating back a decade or more and a unit capable of making 100 bbl. a day of polymer gasoline was constructed as early as 1930. Important strides have been made during 1935 looking to the more general commercialization of available processes, and some four important groups are furthering this work. In addition to the production of liquid products for inclusion as a constituent of commercial motor fuel, polymerization has also been a factor leading to the installation of a plant at the Houston refinery of The Shell Petroleum Corporation for manufacturing isooctane for aviation use, by making available dibutylene for catalytic hydrogenation Polymerization is not confined to unsaturated hydrocarbon gases as a source of raw material, and has been extended to include a preliminary decomposition of normal saturated gases under suitable heat and pressure conditions into the unsaturated types, which can then be used as raw material for the polymerization process. Thus there is opened up the possibility of eventually using large quantities of natural gas in the manufacture of high-grade motor fuels, although the early commercial growth will be largely on cracking still gases for economic reasons. Such utilization will result in a somewhat lowered drain on crude-oil reserves and a partial elimination of the

Jan 1, 1936

By Walter Miller

Any annual review of engineering progress in petroleum refining must of necessity include many features mentioned in earlier reviews. Advances do not spring mushroom fashion to wide acceptance overnight, but rather resemble rolling snowballs, gathering size and velocity as they progress. The new ideas of one year develop through the course of scattered adoption and testing during following years, to be ultimately discarded or to become an integral part of refinery engineering and operation. Polymerization and Cracking As an illustration, the publicity given to the polymerization and cracking of petroleum gases during the year has given many the impression that this is a new art. But patent and technical literature have disclosed active work on the problem dating back a decade or more and a unit capable of making 100 bbl. a day of polymer gasoline was constructed as early as 1930. Important strides have been made during 1935 looking to the more general commercialization of available processes, and some four important groups are furthering this work. In addition to the production of liquid products for inclusion as a constituent of commercial motor fuel, polymerization has also been a factor leading to the installation of a plant at the Houston refinery of The Shell Petroleum Corporation for manufacturing isooctane for aviation use, by making available dibutylene for catalytic hydrogenation Polymerization is not confined to unsaturated hydrocarbon gases as a source of raw material, and has been extended to include a preliminary decomposition of normal saturated gases under suitable heat and pressure conditions into the unsaturated types, which can then be used as raw material for the polymerization process. Thus there is opened up the possibility of eventually using large quantities of natural gas in the manufacture of high-grade motor fuels, although the early commercial growth will be largely on cracking still gases for economic reasons. Such utilization will result in a somewhat lowered drain on crude-oil reserves and a partial elimination of the

Jan 1, 1936

By R. L. Boyer, F. Morgan, M. Muskat

In the last several years a type of application of the fundamental permeability-saturation relationships has been developed which offers great promise in the interpretation of general reservoir performance.l-' In these developments no attempt is made to solve the detailed flow dynamics in actual oil and gas-producing systems. That problem still remains unsolved. But the permeability-saturation phenomena are incorporated in the analysis of oil-producing reservoirs in a manner such as to reflect the true role they play in controlling the gross reservoir behavior. In particular, they are introduced in such a manner as to determine the gas-oil ratio of the production at any stage of depletion, and, when combined explicitly with the so-called material-balance principles in differential form, one can obtain a differential equation describing completely the average pressure and gas-oil-ratio history of oil-producing reservoirs. While thus far they have been applied directly only to gas-drive reservoirs, they are susceptible of extension to partial water-drive systems, and qualitatively the same principles are of value in the study Of complete water-drive reservoirs. Moreover, in addition to giving a means for computing the variation of the reservoir pressure and gas-oil ratios vs. the cumulative production, they automatically lead to predictions of the gross ultimate recovery under natural depletion—and when properly extended they provide means for predicting the ultimate recovery under gas or water injection. The data required for such applications are the initial fluid distribution in the producing section, the pressure-volume-temperature data on the gas and liquid phases, and the permeability-saturation relationship for the oil-satuiated zone. The former can be obtained with reasonable accuracy by methods that are well established and available throughout the industry. The permeability-saturation data, however, involve techniques that are not at all standardized. In fact, only

Jan 1, 1947

By M. Muskat, R. L. Boyer, F. Morgan

In the last several years a type of application of the fundamental permeability-saturation relationships has been developed which offers great promise in the interpretation of general reservoir performance.l-' In these developments no attempt is made to solve the detailed flow dynamics in actual oil and gas-producing systems. That problem still remains unsolved. But the permeability-saturation phenomena are incorporated in the analysis of oil-producing reservoirs in a manner such as to reflect the true role they play in controlling the gross reservoir behavior. In particular, they are introduced in such a manner as to determine the gas-oil ratio of the production at any stage of depletion, and, when combined explicitly with the so-called material-balance principles in differential form, one can obtain a differential equation describing completely the average pressure and gas-oil-ratio history of oil-producing reservoirs. While thus far they have been applied directly only to gas-drive reservoirs, they are susceptible of extension to partial water-drive systems, and qualitatively the same principles are of value in the study Of complete water-drive reservoirs. Moreover, in addition to giving a means for computing the variation of the reservoir pressure and gas-oil ratios vs. the cumulative production, they automatically lead to predictions of the gross ultimate recovery under natural depletion—and when properly extended they provide means for predicting the ultimate recovery under gas or water injection. The data required for such applications are the initial fluid distribution in the producing section, the pressure-volume-temperature data on the gas and liquid phases, and the permeability-saturation relationship for the oil-satuiated zone. The former can be obtained with reasonable accuracy by methods that are well established and available throughout the industry. The permeability-saturation data, however, involve techniques that are not at all standardized. In fact, only

Jan 1, 1947

By Norris Johnston, Carrol M. Beeson

The gravimetric-vacuum distillation method was developed to permit rapid and accurate determinations of the oil-water ratios of small samples or sands containing little oil. In addition, the samples usually are so well cleaned and so little altered by the distillation at reduced pressure that rapid estimations of other physical properties may be made with the evacuated cores. Requiring only elementary glass-blowing technique, the distilling tubes and traps used in determining oil-water ratios were easily fashioned from the usual glassware. A sketch and description are given of the necessary apparatus, including the cylindrical electrical heaters. The procedure, requiring about 40 min., consists in raising the temperature and maintaining it between 675' and 725°F. for at least 10 min. while the pressure is held between I and 2 mm. Hg. The fluids condensed in the trap (cooled by a mixture of kerosine and solid carbon dioxide) are separated in a centrifuge and the volume of water is recorded. Determination of changes in weight with an analytical balance of all parts of the apparatus permits computation of weight of oil distilled and total weight of oil recovered. Introduction In determining the oil-water ratios of core samples, distillation at atmospheric pressurel-5 has proved to be sufficiently reliable for samples containing moderate quantities of oil. Since small samples and sands with little oil are encountered, how- ever, it appeared advisable to develop a method that would be applicable under these circumstances. Thegravimetric-extraction procedure1,6-9 undoubtedly is very reliable and could be used in all tests, but the time consumed in the determination would often delay field operations. This would be especially true when dealing with tight sands or viscous oils, both of which retard the extraction process. Accordingly, the gravimetric-vacuum distillation method was developed in order to combine the good features of both of the older methods; that is, accuracy and speed. By reducing the pressure, it was found possible to perform the distillation at a temperature that permits the use of glass apparatus, all parts of which can be weighed on an analytical balance. Thus, the fluids may be removed quickly from the core, the water is readily trapped and measured, and the loss in weight of the core is easily determined. In addition, the total weight of material condensed in the distilling tube and in the trap provides a method of determining the oil-water ratio that is practically independent of the one involving the loss in weight of the sample. The use of vacuum not only permits as much accuracy as does the gravimetric-extraction process, but it actually allows an increase in speed over the atmospheric-distillation method, because of the time required to cool the metal pots from about 1200°F. between runs. More important yet, the innovation makes possible the almost immediate reporting of permeability, and saturation, which is impossible

Jan 1, 1946

By Norris Johnston, Carrol M. Beeson

The gravimetric-vacuum distillation method was developed to permit rapid and accurate determinations of the oil-water ratios of small samples or sands containing little oil. In addition, the samples usually are so well cleaned and so little altered by the distillation at reduced pressure that rapid estimations of other physical properties may be made with the evacuated cores. Requiring only elementary glass-blowing technique, the distilling tubes and traps used in determining oil-water ratios were easily fashioned from the usual glassware. A sketch and description are given of the necessary apparatus, including the cylindrical electrical heaters. The procedure, requiring about 40 min., consists in raising the temperature and maintaining it between 675' and 725°F. for at least 10 min. while the pressure is held between I and 2 mm. Hg. The fluids condensed in the trap (cooled by a mixture of kerosine and solid carbon dioxide) are separated in a centrifuge and the volume of water is recorded. Determination of changes in weight with an analytical balance of all parts of the apparatus permits computation of weight of oil distilled and total weight of oil recovered. Introduction In determining the oil-water ratios of core samples, distillation at atmospheric pressurel-5 has proved to be sufficiently reliable for samples containing moderate quantities of oil. Since small samples and sands with little oil are encountered, how- ever, it appeared advisable to develop a method that would be applicable under these circumstances. Thegravimetric-extraction procedure1,6-9 undoubtedly is very reliable and could be used in all tests, but the time consumed in the determination would often delay field operations. This would be especially true when dealing with tight sands or viscous oils, both of which retard the extraction process. Accordingly, the gravimetric-vacuum distillation method was developed in order to combine the good features of both of the older methods; that is, accuracy and speed. By reducing the pressure, it was found possible to perform the distillation at a temperature that permits the use of glass apparatus, all parts of which can be weighed on an analytical balance. Thus, the fluids may be removed quickly from the core, the water is readily trapped and measured, and the loss in weight of the core is easily determined. In addition, the total weight of material condensed in the distilling tube and in the trap provides a method of determining the oil-water ratio that is practically independent of the one involving the loss in weight of the sample. The use of vacuum not only permits as much accuracy as does the gravimetric-extraction process, but it actually allows an increase in speed over the atmospheric-distillation method, because of the time required to cool the metal pots from about 1200°F. between runs. More important yet, the innovation makes possible the almost immediate reporting of permeability, and saturation, which is impossible

Jan 1, 1946

By C. M. Moncrief, B C. Craft

A bentonite-clay drilling mud when treated with tetrasodium pyroarsenate underwent substantially the same reduction in viscosity and water loss as when treated with the complex phosphates. The complex arsenate showed a slightly higher reversion after heating; the other arsenates showed poor viscosity-reducing properties. Introduction During the past 10 years the chemical control of drilling mud has become of major importance in affecting the successful drilling and working over of wells. The desired properties of drilling mud have been well established, and in obtaining these characteristics there has developed a large market for viscosity-reducing chemicals. Viscosity reduction produced by humic acid, tannic acid, sodium silicate, sodium tannate, Calgon, and the complex phosphates has been described by Loomis, Ford, and Fidiam.l The effects Of treatment with complex phosphates and ammonium PolyPhosPhates on the rheological properties of muds were investigated by Fancher2 and the alkali vanadates have been described by Williams.3 Laboratory Investigations It is the purpose of this paper to point out the effects of arsenates in controlling the viscosity and gelling characteristics of a drilling mud. Viscosities and gel strengths were measured at room temperatures with a Stormer viscosimeter calibrated in centipoises and operated at 600 r.p.m. Water loss was determined at 80°F. with the Baroid low-pressure wall-building tester at a pressure of I00 lb. per sq. in. for 30 min. The hydrogen-ion concentration was measured with a glass electrode. The bentonite-clay suspensions were prepared in the laboratory and allowed to age several days before testing. Members of the Arsenic Group in the periodic Table include arsenic, antimony and bismuth, but this investigation was limited to arsenic. Phosphorus also occurs in Group V of the Periodic system and phosphorus and arsenic form many closely related compounds such as pH3 and AsH3, P2O5 and As2O5, H3PO4 and H3AS04 Samples of tetrasodium pyroarsenate were prepared by fusing c.p. disodium arsenate (Na2HA5O4.7H2O). According to Friend,' this re-forms the ortho-arsenate on dissolution in water. Sodium trihydrodiorthoarsenate was prepared as described by Mellor,5 from arsenic pen-toxide as follows: As2O5 + 3H20 -> 2H3AsO4 2H3AS04 + 3NaOH Na3H3(AsO4)2 .3H20 Sodium dihydrogen orthoarsenateWaHz-As04) was obtained by fusing together equivalent quantities of arsenious Oxide and sodium nitrate, dissolving the residue in water and allowing it to crystallize.

Jan 1, 1946

By C. M. Moncrief

A bentonite-clay drilling mud when treated with tetrasodium pyroarsenate underwent substantially the same reduction in viscosity and water loss as when treated with the complex phosphates. The complex arsenate showed a slightly higher reversion after heating; the other arsenates showed poor viscosity-reducing properties. Introduction During the past 10 years the chemical control of drilling mud has become of major importance in affecting the successful drilling and working over of wells. The desired properties of drilling mud have been well established, and in obtaining these characteristics there has developed a large market for viscosity-reducing chemicals. Viscosity reduction produced by humic acid, tannic acid, sodium silicate, sodium tannate, Calgon, and the complex phosphates has been described by Loomis, Ford, and Fidiam.l The effects Of treatment with complex phosphates and ammonium PolyPhosPhates on the rheological properties of muds were investigated by Fancher2 and the alkali vanadates have been described by Williams.3 Laboratory Investigations It is the purpose of this paper to point out the effects of arsenates in controlling the viscosity and gelling characteristics of a drilling mud. Viscosities and gel strengths were measured at room temperatures with a Stormer viscosimeter calibrated in centipoises and operated at 600 r.p.m. Water loss was determined at 80°F. with the Baroid low-pressure wall-building tester at a pressure of I00 lb. per sq. in. for 30 min. The hydrogen-ion concentration was measured with a glass electrode. The bentonite-clay suspensions were prepared in the laboratory and allowed to age several days before testing. Members of the Arsenic Group in the periodic Table include arsenic, antimony and bismuth, but this investigation was limited to arsenic. Phosphorus also occurs in Group V of the Periodic system and phosphorus and arsenic form many closely related compounds such as pH3 and AsH3, P2O5 and As2O5, H3PO4 and H3AS04 Samples of tetrasodium pyroarsenate were prepared by fusing c.p. disodium arsenate (Na2HA5O4.7H2O). According to Friend,' this re-forms the ortho-arsenate on dissolution in water. Sodium trihydrodiorthoarsenate was prepared as described by Mellor,5 from arsenic pen-toxide as follows: As2O5 + 3H20 -> 2H3AsO4 2H3AS04 + 3NaOH Na3H3(AsO4)2 .3H20 Sodium dihydrogen orthoarsenateWaHz-As04) was obtained by fusing together equivalent quantities of arsenious Oxide and sodium nitrate, dissolving the residue in water and allowing it to crystallize.

Jan 1, 1946

By Henry Schaefer

Solution by electric analogy of performance problems of reservoirs containing oil and gas has heretofore depended upon a process of successive approximations based on material-balance calculations, because of variation in fluid compressibility. By the addition or subtraction of electric condenser capacity, the analogy network can be adjusted automatically for changing compressibility due to evolution of gas in the reservoir. The addition of a condenser is accomplished by an electronic circuit, which is described; subtracting a condenser is done by merely opening the electrical circuit by means of a relay. Introduction V. Paschkis and H. D. Baker1 first developed in this country a method of applying the analogy of flow of electric current in noninductive circuits to solution of heat-flow problems and suggested its application for certain other problems, such as flow of fluids or mass transfer and chemical diffusion. Necessary details for applying the analogy to flow of fluids in porous media were developed by IV. A. Bruce;= he classified3 the types of analysis and predictions that can be made by the analogy in class I, when the reservoir contains oil but no gas for the period under consideration; in Class 2, when both oil and gas exist in the free state in the reservoir sometime during the period under consideration. Duplication of bottom-hole pressure history and predictions for class I reservoirs can be obtained directly by electric analogy. Until now, the solution of problems pertaining to reservoirs in class 2 was obtained by successive approximations along with material-balance calculations. The object of this paper is to present a method for simplifying the application of electric analogy to class 2 reservoirs, resulting in a solution of these problems as direct as is possible for class I reservoirs. This is accomplished by an electronic control circuit, which adjusts the analogy network for changing compressibilities of fluids contained in the reservoirs. Analogy Network In electrical phenomena the analogy to two-dimensional fluid flow in a porous media is that of current flow through an ideal conducting sheet. This sheet, perfectly insulated on both sides, has resistance and capacitance uniformly distributed throughout its area but is of negligible inductance. The need for having the surface boundaries perfectly insulated is that good correspondence may be had with a permeable fluid-conducting stratum bounded above and below by impermeable media. 111 actual application the ideal conducting sheet, which has distributed parameters, is replaced by a network having lumped values of resistance and capacitance—the resistances are series elements and the capacitances are shunt elements. The larger the number of lumped

Jan 1, 1947

By Henry Schaefer

Solution by electric analogy of performance problems of reservoirs containing oil and gas has heretofore depended upon a process of successive approximations based on material-balance calculations, because of variation in fluid compressibility. By the addition or subtraction of electric condenser capacity, the analogy network can be adjusted automatically for changing compressibility due to evolution of gas in the reservoir. The addition of a condenser is accomplished by an electronic circuit, which is described; subtracting a condenser is done by merely opening the electrical circuit by means of a relay. Introduction V. Paschkis and H. D. Baker1 first developed in this country a method of applying the analogy of flow of electric current in noninductive circuits to solution of heat-flow problems and suggested its application for certain other problems, such as flow of fluids or mass transfer and chemical diffusion. Necessary details for applying the analogy to flow of fluids in porous media were developed by IV. A. Bruce;= he classified3 the types of analysis and predictions that can be made by the analogy in class I, when the reservoir contains oil but no gas for the period under consideration; in Class 2, when both oil and gas exist in the free state in the reservoir sometime during the period under consideration. Duplication of bottom-hole pressure history and predictions for class I reservoirs can be obtained directly by electric analogy. Until now, the solution of problems pertaining to reservoirs in class 2 was obtained by successive approximations along with material-balance calculations. The object of this paper is to present a method for simplifying the application of electric analogy to class 2 reservoirs, resulting in a solution of these problems as direct as is possible for class I reservoirs. This is accomplished by an electronic control circuit, which adjusts the analogy network for changing compressibilities of fluids contained in the reservoirs. Analogy Network In electrical phenomena the analogy to two-dimensional fluid flow in a porous media is that of current flow through an ideal conducting sheet. This sheet, perfectly insulated on both sides, has resistance and capacitance uniformly distributed throughout its area but is of negligible inductance. The need for having the surface boundaries perfectly insulated is that good correspondence may be had with a permeable fluid-conducting stratum bounded above and below by impermeable media. 111 actual application the ideal conducting sheet, which has distributed parameters, is replaced by a network having lumped values of resistance and capacitance—the resistances are series elements and the capacitances are shunt elements. The larger the number of lumped

Jan 1, 1947

By E. S. Grumell

The correct sampling of coal and coke is becoming important to an ever increasing number of producers and consumers. This, therefore, may be an opportune moment to examine where we stand with regard to existing and proposed methods. In this paper an attempt will be made to review, as briefly as possible, some of the considerable amount of painstaking research which has been done in the last 10 years, and which has unquestionably led to a much better understanding of the subject. In so doing we shall try, on the one hand, to make clear where substantial progress has been made, and on the other hand, to draw attention to points that require further investigation. The paper is divided into sections in order to emphasize the major divisions of the subject; further, in order to retain this emphasis, detailed consideration of some of the points has been relegated to appendixes. No attempt has been made to give a complete survey of the literature, as this has already been done by L. A. Bushell.2 The following abbreviations will be used: A.E., average error; P.E., probable error; S.W.R., size-weight ratio; B.S.I., British Standards Institution. Section 1.—Cost It has often been stated that the cost of sampling should bear some relationship to the value of the product, and since coal is a relatively cheap raw material it would be a major error to specify, for ordinary commercial purposes, elaborate and costly methods of sampling which nobody would adopt. Specifications must be of such a nature that they will be used. We believe that one of the achievements of the last 10 years has been to reduce the cost of sampling. There is, however, another point to be considered; via., that the cost of sampling should bear some relationship to the value of the investigation. Correct sampling is a cog (possibly a small one) in the wheel

Jan 1, 1940

By E. S. Grumell

The correct sampling of coal and coke is becoming important to an ever increasing number of producers and consumers. This, therefore, may be an opportune moment to examine where we stand with regard to existing and proposed methods. In this paper an attempt will be made to review, as briefly as possible, some of the considerable amount of painstaking research which has been done in the last 10 years, and which has unquestionably led to a much better understanding of the subject. In so doing we shall try, on the one hand, to make clear where substantial progress has been made, and on the other hand, to draw attention to points that require further investigation. The paper is divided into sections in order to emphasize the major divisions of the subject; further, in order to retain this emphasis, detailed consideration of some of the points has been relegated to appendixes. No attempt has been made to give a complete survey of the literature, as this has already been done by L. A. Bushell.2 The following abbreviations will be used: A.E., average error; P.E., probable error; S.W.R., size-weight ratio; B.S.I., British Standards Institution. Section 1.—Cost It has often been stated that the cost of sampling should bear some relationship to the value of the product, and since coal is a relatively cheap raw material it would be a major error to specify, for ordinary commercial purposes, elaborate and costly methods of sampling which nobody would adopt. Specifications must be of such a nature that they will be used. We believe that one of the achievements of the last 10 years has been to reduce the cost of sampling. There is, however, another point to be considered; via., that the cost of sampling should bear some relationship to the value of the investigation. Correct sampling is a cog (possibly a small one) in the wheel

Jan 1, 1940