Search Documents

By G. B. Gould, H. L. Brunjes

The softening temperature of coal ash, as determined in the laboratory, has been used for years as an indication of the tendency of coal to form clinker and slag. It has not, however, provided an index of unfailing and complete reliability for forecasting the relative performance of different coals, even in the same plant and under the same conditions of operation. A large amount of investigation has been done in attempts to account for this, but practically all of this has been in the direction of studying the chemical constitution of coal ash. Much has been learned, but without much progress toward a better practical application of knowledge to the selection of coal. There has always seemed to be an important factor that eluded discovery. It has long been recognized that the ash-softening temperature as determined in the laboratory had one weakness, in that it represented the temperature at which a thorough mixture of the whole ash of the coal would melt, the mixing having taken place before the heal was applied. This does not, of course, simulate what takes place in practice. With certain exceptions, which will be noted later, almost all of the investigations that have been made, especially the chemical studies of coal ash, have likewise dealt with a mixture of the whole ash in the coal. The present investigation differs from these fundamentally in its approach to the problem. It started from the observation that some clinkering and slagging obviously takes place in a boiler furnace at temperatures below the laboratory-determined ash-softening temperature of the coal. Knowing that coal as it is shipped to market is a heterogeneous mixture of diverse mineral substances, each of which may act independently of the others in the initial stages of clinker and slag formation, it seemed logical to investigate separately the softening temperature of the ash in physically separable portions of the coal, and to determine the relative quantities of ash contributed by each portion. While the data are far from complete, covering as they do only a few coals, and while the conclusions to be reached from the data at this stage arc, in some measure, speculative, they are presented at this time because

Jan 1, 1940

By J. L. Leland Myer

Some of the early experiments on the oxidation temperature of coal1 were undertaken in England in connection with a study of self-heating, or spontaneous combustion. It was then suspected that coals with low oxidation temperature were most likely to ignite by self-heating, but further experiments showed that many additional factors were involved. The oxidation temperature has importance as a physical property or characteristic of the coal. While only a few of the physical properties have been studied, they appear to have basic significance2 in the ultimate classification of all coals. When reliable data become available on the oxidation temperatures, as determined by standard and adequate methods, it should provide an additional basis for classification and comparative evaluation. Oxidation Temperature Defined For such a heterogeneous substance as coal is known to be, no simple definition of oxidation temperature can be established on a theoretical basis. If coals were homogeneous and of simpler structure, the accepted definition of "ignition temperature " as applied to simple gaseous mixtures might be adopted; that is, the temperature at which self-heating of the mixture sets in. But most coals self-heat slightly even at storage temperature, as evidenced by spontaneous combustion, and the definition for gases cannot be applied to coals with any exactness. By subjecting coals to suitable experimental conditions various oxidation characteristics can be obtained and examined for critical or significant stages of the oxidation process. Oxidation temperature itself must then be defined on the basis of such experimental results. Experimental Methods Attempts to determine critical points in the temperature functions of coal undergoing oxidation have resulted in the following experimental methods:

Jan 1, 1932

By E. C. Truesdale, Gerald Edmunds

A few years ago H. M. Cyr, working in the Research Laboratories of The New Jersey Zinc Co., produced a few pounds of zinc1 of such purity that no other elements were detected in it by spectrographic analysis, using the facilities then available. This zinc contained less than one ten-thousandth of one per cent of metallic impurities.&apos; During the decade that followed upon the laboratory production of this "spectro-graphically pure" zinc, commercial developments brought about the production of large tonnages of zinc of purity exceeding 99.99 per cent, and today zinc of 99.999 per cent purity is produced and marketed as "chemically pure" zinc. Typical analyses of present supplies of high-purity zinc are given in Table 1. Table 1.—Typical Analyses Percentnge by Weight Sum of Zinc Fe, Ib1 Fe Cd 1A1 cd Special High Grade*.......... 0.007b 0.005b 0.005b none O.OIOb C.P. (chemically pure)......... < 0.0002 0.0005c 0.000052 S.P. (spectrographically pure).. <0.0002d <0.00005d a A.S.T.M. Standard Specification for Special High Grade Slab Zinc (A.S.T.M. Designation: B 637). b Maximum. &apos; Fe chemically determined. Pb and Cd are spectrographically determined. d Differences between composition of C.P. and S.P. zinc are discussed later in this paper. The availability of commercial tonnages of special high-grade zinc has been the basis for the development of the zinc-base die-casting alloy industry which, in the year 1936, consumed one-eighth of the zinc used in the United States for all purposes. This and the C.P. and S.P. grades have given impetus to scientific investigations into the properties of pure

Jan 1, 1939

By E. C. Truesdale, Gerald Edmunds

A few years ago H. M. Cyr, working in the Research Laboratories of The New Jersey Zinc Co., produced a few pounds of zinc1 of such purity that no other elements were detected in it by spectrographic analysis, using the facilities then available. This zinc contained less than one ten-thousandth of one per cent of metallic impurities.&apos; During the decade that followed upon the laboratory production of this "spectro-graphically pure" zinc, commercial developments brought about the production of large tonnages of zinc of purity exceeding 99.99 per cent, and today zinc of 99.999 per cent purity is produced and marketed as "chemically pure" zinc. Typical analyses of present supplies of high-purity zinc are given in Table 1. Table 1.—Typical Analyses Percentnge by Weight Sum of Zinc Fe, Ib1 Fe Cd 1A1 cd Special High Grade*.......... 0.007b 0.005b 0.005b none O.OIOb C.P. (chemically pure)......... < 0.0002 0.0005c 0.000052 S.P. (spectrographically pure).. <0.0002d <0.00005d a A.S.T.M. Standard Specification for Special High Grade Slab Zinc (A.S.T.M. Designation: B 637). b Maximum. &apos; Fe chemically determined. Pb and Cd are spectrographically determined. d Differences between composition of C.P. and S.P. zinc are discussed later in this paper. The availability of commercial tonnages of special high-grade zinc has been the basis for the development of the zinc-base die-casting alloy industry which, in the year 1936, consumed one-eighth of the zinc used in the United States for all purposes. This and the C.P. and S.P. grades have given impetus to scientific investigations into the properties of pure

Jan 1, 1939

The Round Table on Qualities of Pig Iron, under the auspices of the Joint Committee on Qualities of Pig Iron, which is made up of members of the American Institute of Mining and Metallurgical Engineers, the American Foundrymen&apos;s Association, the American Society for Testing Materials, the Gray Iron Institute, and the Malleable Iron Institute, was held at the Palmer House, Chicago, III., on Oct. 1, 1935. Prcoeedings R. H. SwEEtseR,* New York, N. Y.—Seven years ago last June, in Chicago, we had a round table on qualities of pig iron1, and at that time the foundrymen were out with their battle-axes for the blast-furnace men, and the open-hearth men were doing the same thing. After that meeting there was really a determined effort to find out about the qualities of pig iron, and great progress has been made all along the line. This afternoon we want to have a frank discussion of the qualities of pig iron, whether it is the molten pig iron going into the steel plant, or cold pigs going to the different foundries. We ought to hear something from Dr. J. T. MacKenzie, who is chairman of the Joint Committee, and from Mr. R. E. Kennedy, the Technical Secretary of the American Foundrymen&apos;s Association. J. T. MacKEnzie,† Birmingham, A1a.—As a result of that meeting in Chicago, there was considerable agitation in the Foundrymen&apos;s Association to develop a set of tests for pig iron. One of the difficulties was that nobody talked the same language on shrinkage, draws, live iron, dead iron, and so forth, which were the main complaints against pig iron. By request of a committee of the Foundrymen&apos;s Association, the Bureau of Standards ran a comprehensive set of tests that did develop the principles governing the optical pyrometer as applied to cast iron and pig iron. Then the Bureau went on further with the fluidity test, and developed a method for the absolute changes of volume at the freezing point. There is one serious gap in the yardstick, which has never been developed, and that is the tendency to draws from heavy sections to light. Everyone who has worried about the differences of section, and sponginess in changes of section, realizes that the

Jan 1, 1936

The Round Table on Qualities of Pig Iron, under the auspices of the Joint Committee on Qualities of Pig Iron, which is made up of members of the American Institute of Mining and Metallurgical Engineers, the American Foundrymen&apos;s Association, the American Society for Testing Materials, the Gray Iron Institute, and the Malleable Iron Institute, was held at the Palmer House, Chicago, III., on Oct. 1, 1935. Prcoeedings R. H. SwEEtseR,* New York, N. Y.—Seven years ago last June, in Chicago, we had a round table on qualities of pig iron1, and at that time the foundrymen were out with their battle-axes for the blast-furnace men, and the open-hearth men were doing the same thing. After that meeting there was really a determined effort to find out about the qualities of pig iron, and great progress has been made all along the line. This afternoon we want to have a frank discussion of the qualities of pig iron, whether it is the molten pig iron going into the steel plant, or cold pigs going to the different foundries. We ought to hear something from Dr. J. T. MacKenzie, who is chairman of the Joint Committee, and from Mr. R. E. Kennedy, the Technical Secretary of the American Foundrymen&apos;s Association. J. T. MacKEnzie,† Birmingham, A1a.—As a result of that meeting in Chicago, there was considerable agitation in the Foundrymen&apos;s Association to develop a set of tests for pig iron. One of the difficulties was that nobody talked the same language on shrinkage, draws, live iron, dead iron, and so forth, which were the main complaints against pig iron. By request of a committee of the Foundrymen&apos;s Association, the Bureau of Standards ran a comprehensive set of tests that did develop the principles governing the optical pyrometer as applied to cast iron and pig iron. Then the Bureau went on further with the fluidity test, and developed a method for the absolute changes of volume at the freezing point. There is one serious gap in the yardstick, which has never been developed, and that is the tendency to draws from heavy sections to light. Everyone who has worried about the differences of section, and sponginess in changes of section, realizes that the

Jan 1, 1936

By Alexander L. Field

In the light of the experimental data on equilibrium for the reaction C + FeO = Fe + CO in molten steel recently obtained by Kinzel and Egan,l it is necessary to revise current theories regarding the nature of equilibrium between carbon and FeO in the basic open-hearth furnace. According to the measurements of these investigators the equilibrium constant m for the above reaction for a pressure of dissolved CO equal to 1 atm. is equal to 0.0005 at 1550" C., when concentrations of carbon and FeO are expressed in percentages by weight. Their work also shows that, with the pressure of CO fixed at 1 atm., not only is the product of carbon and FeO constant, but carbon and FeO are each independently constant—a circumstance which might have been predicted from theoretical considerations. At 1550" C., carbon is constant at about 0.025 per cent. and FeO at about 0.020 per cent., with the pressure of dissolved CO equal to 1 atm., the product of these two constants being equal to the originally mentioned constant of 0.0005. Available data on the dissolved FeO content of samples taken from the metal bath at practical slag-metal equilibrium prove that this FeO content is determined solely by temperature and the effective FeO content of the slag. The distribution constant r at 1550" C., as determined by Herty, Gaines, Larsen, Simkins, Geruso and Watkins2 is equal to 0.0086. A slag would have to contain 0.020 = 2.3 per cent. effective 0.0086 FeO or less in order to prevent the metal from containing more dissolved FeO than that required for equilibrium with CO at 1 atm. pressure. Such low percentages of FeO are never found in basic open-hearth slags at the completion of a heat when rate of carbon drop has become practi-

Jan 1, 1930

By Cyril Wells, Robert F. Mehl

The diffusion of carbon in gamma iron plays an essential role in many metallurgical processes. In carburizing, in graphitizing, in homogenizing, in the formation of pearlite from austenite, and in other processes, migration of carbon in gamma iron occurs.1&apos;2 A full understanding of the rate at which these processes occur obviously requires a knowledge of the rate of diffusion of carbon. In carburizing, for example, the depth of carbon pentration is determined by the carbon concentration in solid solution at the surface, and by the rate of diffusion inward of the carbon. Until reliable data on the rates of diffusion of carbon are available it is unlikely that a full quantitative description of this process will be obtained. In the formation of pearlite from austenite, the segregation of carbon and alpha iron from the austenite obviously requires the diffusion of carbon; the rate at which pearlite nodules grow is evidently controlled at least in part by the rate of diffusion of carbon; it is unlikely that we shall understand the factors that determine the rate of growth unless data on rates of diffusion of carbon, and the variation of these with composition, grain size, and temperature are available. Accordingly it was decided: (1) to determine, more accurately than hitherto, the diffusion coefficients of carbon in austenite over a wide temperature and a wide concentration range, (2) to study the influence of grain size and impurities on this diffusion coefficient, and (3) to study the effect of manganese and nickel on the rate of diffusion of carbon in the austenite of manganese and nickel steels, respectively; the influence of carbon on the rate of diffusion of manganese and of nickel will be made the subject of later papers. The rate of diffusion of carbon in gamma iron has been studied by Runge3 by Tammann and Schonert4, by Bramley and co-authors,5-14 and

Jan 1, 1940

By Cyril Wells, Robert F. Mehl

The diffusion of carbon in gamma iron plays an essential role in many metallurgical processes. In carburizing, in graphitizing, in homogenizing, in the formation of pearlite from austenite, and in other processes, migration of carbon in gamma iron occurs.1&apos;2 A full understanding of the rate at which these processes occur obviously requires a knowledge of the rate of diffusion of carbon. In carburizing, for example, the depth of carbon pentration is determined by the carbon concentration in solid solution at the surface, and by the rate of diffusion inward of the carbon. Until reliable data on the rates of diffusion of carbon are available it is unlikely that a full quantitative description of this process will be obtained. In the formation of pearlite from austenite, the segregation of carbon and alpha iron from the austenite obviously requires the diffusion of carbon; the rate at which pearlite nodules grow is evidently controlled at least in part by the rate of diffusion of carbon; it is unlikely that we shall understand the factors that determine the rate of growth unless data on rates of diffusion of carbon, and the variation of these with composition, grain size, and temperature are available. Accordingly it was decided: (1) to determine, more accurately than hitherto, the diffusion coefficients of carbon in austenite over a wide temperature and a wide concentration range, (2) to study the influence of grain size and impurities on this diffusion coefficient, and (3) to study the effect of manganese and nickel on the rate of diffusion of carbon in the austenite of manganese and nickel steels, respectively; the influence of carbon on the rate of diffusion of manganese and of nickel will be made the subject of later papers. The rate of diffusion of carbon in gamma iron has been studied by Runge3 by Tammann and Schonert4, by Bramley and co-authors,5-14 and

Jan 1, 1940

By Cyril Wells, Robert F. Mehl

The practical importance of a knowledge of the rates of diffusion of carbon and of alloying elements in steel has often been pointed out.l,13 This importance lies chiefly, though by no means only, in the study of carbufizing and in the study of reactions involved in the eutectoid inversion in steel. The present paper is one of a series in which the rates of diffusion of carbon and of alloying elements in ?-Fe and their mutual effects are measured with precision. The present paper reports the results of measurements of diffusion coefficients D of manganese in ?-Fe over wide ranges of temperature, and concentration, and of the effect of carbon and impurities and of grain size upon these diffusion coefficients.‡ Data on the rate of diffusion of manganese in ?-Fe have been reported by Fry2 and by Paschke and Hauttmann.3 Claussen4 calculated the diffusion coefficient D from Fry&apos;s data as 3 X 10-10 sq, cm. per set. at 960º, which will be shown to be incorrect by many orders of magnitude. Paschke and Hauttmann gave a rough value of 9.6 x 10-8 Sq. cm. per set. at 14000. Neither of these workers considered the variation of D with concentration and with temperature, and neither studied the effect of carbon. Method and Materials Method.—The method employed is identical with that used earlier.5 Owing to the volatility of manganese and the consequent loss of manganese from the outer surfaces of the welded diffusion bars, these surfaces were discarded. The diffusion anneals were performed in argon, except One (test 18) in which hydrogen was employed for purposes noted below. The temperatures reported are accurate to about 3" and constant within 1°C; the diffusion times are reported to the nearest half hour. The specimens were furnace-coo1ed after the diffusion ation, at about 2° per min. Layers, usually 0.004 in. thick, parallel to the welded interface, were machined from the specimens after the diffusion anneal and analyzed for manganese to 0.I Per cent Mn; the distances of these layers from the interface was measured to ±0.0002 in. The concentration-penetration curves obtained were analyzed by both the Grube and the Matano solutions.8 The D values calculated by these two methods do not differ appreci000. The Grube solution was used except in tests in which the effect of concentration upon D was greater than so per cent; in such cases the Matano method, which explicitly provides for the variation of D with concentration,&apos; is the more reliable. In general, the number of layers machined from the zones of variable composition were large enough to permit the use of the average layer composition as that of the center of the layer. In 3 of the 3&apos; tests, however, this is not justified, and the D values

Jan 1, 1941

By Cyril Wells, Robert F. Mehl

The practical importance of a knowledge of the rates of diffusion of carbon and of alloying elements in steel has often been pointed out.l,13 This importance lies chiefly, though by no means only, in the study of carbufizing and in the study of reactions involved in the eutectoid inversion in steel. The present paper is one of a series in which the rates of diffusion of carbon and of alloying elements in ?-Fe and their mutual effects are measured with precision. The present paper reports the results of measurements of diffusion coefficients D of manganese in ?-Fe over wide ranges of temperature, and concentration, and of the effect of carbon and impurities and of grain size upon these diffusion coefficients.‡ Data on the rate of diffusion of manganese in ?-Fe have been reported by Fry2 and by Paschke and Hauttmann.3 Claussen4 calculated the diffusion coefficient D from Fry&apos;s data as 3 X 10-10 sq, cm. per set. at 960º, which will be shown to be incorrect by many orders of magnitude. Paschke and Hauttmann gave a rough value of 9.6 x 10-8 Sq. cm. per set. at 14000. Neither of these workers considered the variation of D with concentration and with temperature, and neither studied the effect of carbon. Method and Materials Method.—The method employed is identical with that used earlier.5 Owing to the volatility of manganese and the consequent loss of manganese from the outer surfaces of the welded diffusion bars, these surfaces were discarded. The diffusion anneals were performed in argon, except One (test 18) in which hydrogen was employed for purposes noted below. The temperatures reported are accurate to about 3" and constant within 1°C; the diffusion times are reported to the nearest half hour. The specimens were furnace-coo1ed after the diffusion ation, at about 2° per min. Layers, usually 0.004 in. thick, parallel to the welded interface, were machined from the specimens after the diffusion anneal and analyzed for manganese to 0.I Per cent Mn; the distances of these layers from the interface was measured to ±0.0002 in. The concentration-penetration curves obtained were analyzed by both the Grube and the Matano solutions.8 The D values calculated by these two methods do not differ appreci000. The Grube solution was used except in tests in which the effect of concentration upon D was greater than so per cent; in such cases the Matano method, which explicitly provides for the variation of D with concentration,&apos; is the more reliable. In general, the number of layers machined from the zones of variable composition were large enough to permit the use of the average layer composition as that of the center of the layer. In 3 of the 3&apos; tests, however, this is not justified, and the D values

Jan 1, 1941

By R. F. Mehl, B. Lustman

The formation of intermediate phase layers in cementation processes has been subjected to extensive qualitative investigation though to relatively little quantitative study; this work has recently been fully summarized by F. N. Rhines.&apos; It is necessary here only to cnumerate the general conclusions drawn concerning the kinetic laws governing the growth of intermediate layers and to state what is known concerning the structural changes accompanying the generation of phase layers. I. When the intermediate phase is protective in type—i.e., when its density is less than that of the base metal, so that a continuous coating is formed and maintained—the isothermal growth of the phase follows a simple parabolic equation: X2 = kt [i] where X is the thickness of the alloy layer, k thc reaction rate constant, and t the time. The applicability of this equation to diffusion processes is tested by plotting the square of the thickness versus time, or by plotting the thickness versus the square root of time; the resultant achievement of a straight line in such a plot has been considered sufficient proof of the validity of this equation. Exceptions have been found where liquid phases are involved in the reaction, where the diffusion layer is cracked,2 and where thin semimetallic oxide and sulphide coatings are formed on metals.$ In the first two cases the thickness increases linearly with time, and in the latter it is a logarithmic function of time. 2. The rate of thickening varics with temperature according to the Arrhenius equation: k = Ae-Q/RT [2] where k is the parabolic rate constant of Eq. I, or some other rate-descriptive function, A is the action constant, e the base of natural logarithms, Q the heat of activation, R the gas constant, and T absolute temperature. This equation has been found to be generally valid except when transformations occur during reaction in either the base metal or in the reaction layer; in such instances Eq. 2 is still applicable with different values for the constants A and Q above and below the transformation temperature. 3. Ali phases that are stable at the temperature at which diffusion occurs will appear in the interdiffusion of two components. In some cases certain of the phases may be too thin to be observed and identified easily. Nonequilibrium phases have never been noted in thick reaction layers; i.e., layers of a thickness that may be discerned microscopically. The relative thickness of each phase in a diffusion layer is proportional to the concentration gradient and to the rate of diffusion in that phase.4 The reaction layers tend to have a

Jan 1, 1942

By R. F. Mehl, B. Lustman

The formation of intermediate phase layers in cementation processes has been subjected to extensive qualitative investigation though to relatively little quantitative study; this work has recently been fully summarized by F. N. Rhines.&apos; It is necessary here only to cnumerate the general conclusions drawn concerning the kinetic laws governing the growth of intermediate layers and to state what is known concerning the structural changes accompanying the generation of phase layers. I. When the intermediate phase is protective in type—i.e., when its density is less than that of the base metal, so that a continuous coating is formed and maintained—the isothermal growth of the phase follows a simple parabolic equation: X2 = kt [i] where X is the thickness of the alloy layer, k thc reaction rate constant, and t the time. The applicability of this equation to diffusion processes is tested by plotting the square of the thickness versus time, or by plotting the thickness versus the square root of time; the resultant achievement of a straight line in such a plot has been considered sufficient proof of the validity of this equation. Exceptions have been found where liquid phases are involved in the reaction, where the diffusion layer is cracked,2 and where thin semimetallic oxide and sulphide coatings are formed on metals.$ In the first two cases the thickness increases linearly with time, and in the latter it is a logarithmic function of time. 2. The rate of thickening varics with temperature according to the Arrhenius equation: k = Ae-Q/RT [2] where k is the parabolic rate constant of Eq. I, or some other rate-descriptive function, A is the action constant, e the base of natural logarithms, Q the heat of activation, R the gas constant, and T absolute temperature. This equation has been found to be generally valid except when transformations occur during reaction in either the base metal or in the reaction layer; in such instances Eq. 2 is still applicable with different values for the constants A and Q above and below the transformation temperature. 3. Ali phases that are stable at the temperature at which diffusion occurs will appear in the interdiffusion of two components. In some cases certain of the phases may be too thin to be observed and identified easily. Nonequilibrium phases have never been noted in thick reaction layers; i.e., layers of a thickness that may be discerned microscopically. The relative thickness of each phase in a diffusion layer is proportional to the concentration gradient and to the rate of diffusion in that phase.4 The reaction layers tend to have a

Jan 1, 1942

By C. R. Fondersmith, John Chipman

In the manufacture of rimming steel—which constitutes the bulk of the world&apos;s production of mild steel—the factors that determine the quality of the product are very closely associated with the pouring and solidification of the steel in the ingot mold. The behavior of the metal in the mold is, on the one hand, the resultant of the complex processes through which the liquid metal has passed, and, on the other, it is an indication of the probable behavior of the ingot during subsequent rolling and finishing operations. A detailed study of the mechanism of solidification of rimming ingots ought to yield information that will be useful in controlling the structure of the ingot and the quality of the ultimate product. The first step in such a study is to determine the rate at which the solid shell of the ingot forms from the liquid metal in the mold. A knowledge of the rate of solidification will make it possible to correlate observations of rimming action and gas evolution with studies of the structure, porosity, and segregation within the ingot. Thus, if the metal in the mold is observed to fall, let us say one minute after pouring, the portion of the structure associated with this fall will be located in the part of the ingot that is solidifying at that particular moment. The knowledge that the ingot solidifies to a depth of 3/4 in. in the first minute enables us to locate in the ingot the structural features corresponding to the observed fall. Conversely, the blowhole condition associated with a rising or growing ingot will be found in the part of the ingot that is solidifying at the time the phenomenon occurs. The time required for the complete solidification of an ingot has long been a matter of speculation. It is of considerable practical importance in connection with charging and heating in the soaking pits. Too rapid handling of the ingot through heating and rolling processes has been thought to be associated with excessive pipe and other internal defects, so that a further object of this investigation was to attempt to estimate the time required for complete solidification, or the minimum practical time within which the subsequent operations can be performed with the minimum hazard.

Jan 1, 1937

By Frederick N. Rhines, Robert F. Mehl

It has been shown elsewhere1 that the data on the rates of diffusion in solid metals are fragmentary and in many cases unacceptable. As a result, relatively little is known concerning the factors determining rates of diffusion and the variations in these rates with temperature. The first form of Fick&apos;s law (equation 1 below), in which the diffusion coefficient D is assumed invariant with composition, has been recognized for many years as only an approximation. The differential equation representing the second form of Fick&apos;s law (equation 4 below) has only recently been integrated by Matano,2 and unfortunately only in cases where a full diffusion-penetration curve (concentration-distance curve) has been obtained can the Matano solution be applied. The proper analysis of diffusion data is thus confined to the data of Grube and Jedele and of Jedele. 8 These data are essentially for one temperature alone and do not furnish any information on the variation of the activation heat of diffusion, Q, with concentration: no information exists on the variation of Q with concentration within a single solid solution field. 11 Much of the argument concerning the properties of metals that determine D and Q has been drawn from data in which variations of the quantities with concentration are unknown, for these data have been taken from experiments that could not furnish this information. Speculation concerning the properties of metals that may be effective in determining D and Q on the basis of data in which the chosen D and Q values are averages over wide concentration ranges of values at particular concentrations, ranges often of 100 per cent, is likely not to be fruitful.

Jan 1, 1938

By Frederick N. Rhines, Robert F. Mehl

It has been shown elsewhere1 that the data on the rates of diffusion in solid metals are fragmentary and in many cases unacceptable. As a result, relatively little is known concerning the factors determining rates of diffusion and the variations in these rates with temperature. The first form of Fick&apos;s law (equation 1 below), in which the diffusion coefficient D is assumed invariant with composition, has been recognized for many years as only an approximation. The differential equation representing the second form of Fick&apos;s law (equation 4 below) has only recently been integrated by Matano,2 and unfortunately only in cases where a full diffusion-penetration curve (concentration-distance curve) has been obtained can the Matano solution be applied. The proper analysis of diffusion data is thus confined to the data of Grube and Jedele and of Jedele. 8 These data are essentially for one temperature alone and do not furnish any information on the variation of the activation heat of diffusion, Q, with concentration: no information exists on the variation of Q with concentration within a single solid solution field. 11 Much of the argument concerning the properties of metals that determine D and Q has been drawn from data in which variations of the quantities with concentration are unknown, for these data have been taken from experiments that could not furnish this information. Speculation concerning the properties of metals that may be effective in determining D and Q on the basis of data in which the chosen D and Q values are averages over wide concentration ranges of values at particular concentrations, ranges often of 100 per cent, is likely not to be fruitful.

Jan 1, 1938

By Ernest Kirkendall

The amount of research done in the last fen years on the subject of diffusion in solid metals is significant of the importance of this problem. To review the literature dealing with diffusion is unnecessary here. Deschl in 1912 reviewed the work that had been done on diffusion in solids and gave a bibliography of the literature published before that time. Mehl&apos;s paper in 19362 is an excellent review of diffusion in metals and contains a large bibliography. Of importance also for it? review and bibliography is an article by 14. I. Krynitsky.~ While considerable material lias appeared in the literature on diffusion in brass, the amount of information is not great compared to that pertaining to some of the other alloys. Most of the information published is of a qualitative nature; that which is quantitative varies considerably. Thus the quantitative determination of the rates of diffusion of copper and zinc in alpha brass by a new method appeared worth while. In the present investigation the rate of diffusion of zinc in approximately the same composition alpha brass has been determined :it three temperatures. Procedure The method used consisted of plating copper on a beta brass, heating it, to allow diffusion to take place, and measuring the concentration of copper by determining the lattice constant of the alloy. This method is unique in that it uses a beta brass of such a composition that at the tem perature at which diffusion takes place the beta brass is saturated wit11 copper. Thus, while the beta brass supplies thc zinc, no diffusion takes

Jan 1, 1939

By Ernest Kirkendall

The amount of research done in the last fen years on the subject of diffusion in solid metals is significant of the importance of this problem. To review the literature dealing with diffusion is unnecessary here. Deschl in 1912 reviewed the work that had been done on diffusion in solids and gave a bibliography of the literature published before that time. Mehl&apos;s paper in 19362 is an excellent review of diffusion in metals and contains a large bibliography. Of importance also for it? review and bibliography is an article by 14. I. Krynitsky.~ While considerable material lias appeared in the literature on diffusion in brass, the amount of information is not great compared to that pertaining to some of the other alloys. Most of the information published is of a qualitative nature; that which is quantitative varies considerably. Thus the quantitative determination of the rates of diffusion of copper and zinc in alpha brass by a new method appeared worth while. In the present investigation the rate of diffusion of zinc in approximately the same composition alpha brass has been determined :it three temperatures. Procedure The method used consisted of plating copper on a beta brass, heating it, to allow diffusion to take place, and measuring the concentration of copper by determining the lattice constant of the alloy. This method is unique in that it uses a beta brass of such a composition that at the tem perature at which diffusion takes place the beta brass is saturated wit11 copper. Thus, while the beta brass supplies thc zinc, no diffusion takes

Jan 1, 1939

By J. Murray Riddell, Grover J. Holt, Arthur E. Anderson

Out of the depths of each business cycle we emerge with a stimulus for greater efficiency and a realization of progress in industrial technique. The recent years have not been an exception to this rule, and in retrospect we sense that significant advances have been made in mining practices on the Mesabi Range, with emphasis on speed of production and economy of operation. A survey of such changes does not reveal anything that is fundamentally or basically new, but it is apparent that ideas and machines that have found wide application in industry elsewhere, with necessary modifications, are being put to productive use in mining iron ore. Innovations in transporting and conveying ore from the open pits stand out with greatest prominence, so that, in the main, it will be with these features that this paper will treat, in the review of progress made to this date. The late years have witnessed the development of small deposits for open-pit operation, the cleaning up of pits nearing exhaustion, and in two large operations the approach to the limit for haulage by steam locomotives, owing to grades, making it necessary to recover the ore in slopes, track benches and below the power-shovel limit by a milling and scram operation. For several years small standard-type dump trucks have been used in clean-up or scram operations within the pits, but during the season of 1936 the first effort was made to use heavy truck haulage in the transportation of stripping and iron ore. The new units in use today vary from 15 to 20 tons in capacity, and are equipped with powerful gasoline or Diesel engines and supplemented by trailers or wagons on rubber or crawler treads. The Diesel engine finds favor with most operators because of fuel economy. These units develop upward of 125 hp. in the 15-ton trucks. The speed of these trucks varies from 2 miles per hour in Pow gear to 35 in high gear. The transmission affords 12 speeds forward and 3 speeds in reverse.

Jan 1, 1940

By J. Murray Riddell, Arthur E. Anderson, Grover J. Holt

Out of the depths of each business cycle we emerge with a stimulus for greater efficiency and a realization of progress in industrial technique. The recent years have not been an exception to this rule, and in retrospect we sense that significant advances have been made in mining practices on the Mesabi Range, with emphasis on speed of production and economy of operation. A survey of such changes does not reveal anything that is fundamentally or basically new, but it is apparent that ideas and machines that have found wide application in industry elsewhere, with necessary modifications, are being put to productive use in mining iron ore. Innovations in transporting and conveying ore from the open pits stand out with greatest prominence, so that, in the main, it will be with these features that this paper will treat, in the review of progress made to this date. The late years have witnessed the development of small deposits for open-pit operation, the cleaning up of pits nearing exhaustion, and in two large operations the approach to the limit for haulage by steam locomotives, owing to grades, making it necessary to recover the ore in slopes, track benches and below the power-shovel limit by a milling and scram operation. For several years small standard-type dump trucks have been used in clean-up or scram operations within the pits, but during the season of 1936 the first effort was made to use heavy truck haulage in the transportation of stripping and iron ore. The new units in use today vary from 15 to 20 tons in capacity, and are equipped with powerful gasoline or Diesel engines and supplemented by trailers or wagons on rubber or crawler treads. The Diesel engine finds favor with most operators because of fuel economy. These units develop upward of 125 hp. in the 15-ton trucks. The speed of these trucks varies from 2 miles per hour in Pow gear to 35 in high gear. The transmission affords 12 speeds forward and 3 speeds in reverse.

Jan 1, 1940