Search Documents

By R. Grierson, L. J. Bonis

The high-temperature Strength oF TD nickel has been observed to be dependent upon the previons thermal and mechanical history of the material. Variations in both the level and the anisotropy of strength have been observed. 01 this paper- these variations are correlated with the storing of annealing resistant elastic strain energy in the matrix of the TD nickel. An x-vay line -broadening tecknique is used to measure the maLrTis elastie strain. THE inclusion of a finely dispersed second phase into a ductile matrix has long been recognized as an extremely effective method of strengthening the matrix both at high and at low homologous temperatures. It has been found, however, that the factors which determine the high-temperature strength are not the same as those which are important at low temperatures. Below 0.5 Tm the size and distribution of the second phase particles are of prime importance in determining the strength,')' while above this temperature the strength is mainly dependent upon the previous thermal and mechanical history of the alloy,3-7 This paper is primarily concerned with explaining the response of the high-temperature mechanical strength of one of these alloys (DuPont's TD nickel) to various thermo-mechanical treatments. It will be shown that this response is not associated with the occurrence of any form of dislocation substructure within the matrix of the alloy. It has been found, however, that a correlation does exist between the elastic strain level in the matrix and the previous thermomechanical history of the alloy and that the observed changes in elastic strain level parallel the measured changes in high-temperature strength. It therefore must be concluded that variations in high-temperature strength are a direct result of the variations in elastic strain level. MATERIAL TD nickel contains approximately 2 vol pct of Tho2 in an unalloyed nickel matrix. It is formed, as a powder, by a chemical technique and this powder is compacted to form ingots which are then extruded to give 21/2-in.-diam rod. Rod of smaller diameter is prepared from the as-extruded rod by swaging. In the studies reported in this paper, 1/2-in.-diam rod was used. This rod received an anneal of 1 hr at 1100°C prior to being used in any of these studies. EXPERIMENTAL TECHNIQUES Two methods were used to examine the structure of the nickel matrix of the TD nickel. These were: 1) transmission electron microscopy; 2) the analysis of the position and profile of X-ray diffraction lines obtained using the nickel matrix as the diffracting media. To prepare thin foils for electron-microscopical examination, slices of TD nickel approximately 0.050 in. thick were cut from the as-received 1/2-in.-diam rod. These were then chemically polished down to 0.045 in., rolled to 0.009 in., given a predetermined heat treatment, and thinned, using a modified Bollman technique, to provide the foils for observation. All observations were carried out at 100 kv, using a Hitachi HU-11 electron microscope. Specimens of the undeformed rod were prepared by grinding down the 0.050-in.-thick slices to approximately 0.015 in. and then thinning chemically and electrolytically to give the thin foils. The X-ray specimens were prepared by rolling 0.375-in.-thick rectangular blocks down to 0.075 in. The surfaces of the rolled material were ground flat, chemically polished to remove the layer disturbed by the grinding, and given a predetermined anneal in an inert atmosphere. They were then ground lightly to check their flatness and given a final chemical polish prior to being examined. The X-ray diffraction line profiles were measured using an automated Picker biplane diffractometer. A special specimen holder was built to allow a more accurate and reproducible positioning of the specimen. The line profiles were determined by carrying out intensity measurements at intervals of either 1/30 deg or 1/60 deg over a range of 3 deg on either side of the nickel peaks of interest. A piece of pure nickel which had been recrystallized to give a large grain size was used as a standard to give the X-ray line profile generated by a strain-free matrix. The analysis of the X-ray diffraction line profiles is a modification of that due initially to Warren and Aver-bach8and has been described elsewhere.3 This analysis gives a measurement of two parameters associated with the structure of the nickel matrix. These parameters are: 1) the size of the coherently diffracting domains within the nickel matrix; 2) the magnitude of the elastic strains in these domains. Both of these parameters are first determined in terms of a Fourier series. These series are obtained from other Fourier series which describe the measured profile of the X-ray diffraction lines. Thus, for both the coherently diffracting domain size and the elastic strain level, it is possible to plot Ft (the Fourier coefficient) against t (the term in the Fourier series), where t can be expressed in terms of a distance L and the Fourier coefficient Ft(S) (associated with elastic strain level) can be expressed in terms of the root mean square strain (e2)1/2. Thus a plot of (F 2)1/2 vs L can be obtained. Plots of this type are shown graphically in Figs. 6 and 8. Interpretation

Jan 1, 1968

By John Chipman, Raymond L. Orr

Recently reported high -temperatlnre thermal data have been incorporated in a reuieu' of the therinody-r~ar,zic propesties of iron. The recent data permit mot corlsisterlt and reliuble choices to be made for many of the pvoperties, resnlling in bettev eslablished tabrtlations of the thermodynamic functions. Values of Cp, h°t- - H°298. s°t - S2sa, and (G°T -H298/T are tabulated for -the solid and liquid phases of iron in both stable and melastable regions. Consistency of the tabulations has been maintained to the precision necessr~vg to yield the Gibbs energy change belween the bcc (a, 8) and fcc (y) phases of iron at temperatures pertinenl to alloy studies. THE importance of the metal iron has stimulated many investigations of its thermodynamic properties at elevated temperatures. Reviews and summaries of the data have appeared from time to time. Among these the 1951 paper of Darken and smith' deserves highest recognition for the quality of its criticism and for the precision and thermodynamic consistency of its tabulations. These and the more recent table of Kaufman, Clougherty, and weiss2 reproduce the Gibbs energy of the (a, 6)--Y transformation with sufficient sensitivity for alloy studies. Other recent compilations of equal validity3-' make no attempt to do this. Since this Gibbs energy change is not greater than 22 cal per g-atom over the temperature range 1100° to 1800°K, it is obviously desirable to tabulate values of (G°t - H298)/T to four places of decimals even though the absolute accuracy would not warrant such precision. The necessity for reconsideration of the problem is emphasized by the recent publication of several important researches on the enthalpy and heat capacity of iron. The older work is well-covered in the reviews cited and will be mentioned here only when actually employed in the tabulations. GAMMA IRON Transition temperatures are taken from the selec -tions of Elliott and Gleiser,5 based on the work of Boulanger7 and earlier workers. For the a-y (A3) transition at 1184°K we retain the value 215 cal per g-atom adopted by Darken and smith.' It has received confirmation in the recent work of Dench and Kubaschewski,' and of Braun8 using adiabatic calori-metry, and of Wallace, Sidles, and Danielson10 using a pulse heating technique. The enthalpy data of Olette and ferrier" and of Anderson and Hultgren12 at higher and lower temperatures may be extended to 1184°K to give the following values which are adjusted to the required value of ? 1184 Ha,1184 Ha 298 = 8030 cal per g-atom [11 hr,1184-ha298 = 8245 cal per g-atom [2]

Jan 1, 1968

By Marius S. Darrow, William B. White, Rustum Roy

The PbS-PbTe systen has been studied by quench-ing and D.T.A. techniques f?om 400' to 1150°C. Runs were made in evacuated silica tubes so that all equilibria are at the vapor pressure of the system. Lattice parameters of the quenched salnples , measured by X-ray diffraction, show a complete crystalline-solution series existing over a narrow temperature range between approximately 805" and 871°C. An exsolution dome extends from a maximum of about 805"C (approximately 30 mole pct PbTe) to 1 and 96.5 pet PbTe at 400°C. A narrow melting region, deternined by D.T.A., extends form 918c (mp PbTe), The shapes of the liquides and solidus curves imply the existence of a minimum at 871°C at approximately 65 pct PbTe. THe exact composition of the minimum could not be established due to the very narrow two-phase region. At compositions containing less than 50 pet PbTe, liquidus temperatures begin to increase, while the solidus remains almost flat to about 15 mole pet PbTe before beginning to vise toward the mp of PbS (1075 C). LEAD sulfide and lead telluride are isostructural (NaC1 type) semiconductors whose electrical and optical properties have been extensively studied and used in recent years. If appreciable crystalline solution exists between these compounds, the variation of physical properties with composition could be of interest. The purpose of this investigation was to determine the extent, if any. of crystalline solution, and to obtain the phase diagram for the system. To the knowledge of the authors, only three studies of the system PbS-PbTe have been reported, and, in chronological order, each investigation found an increasing amount of crystalline solution. In 1956, Yamamoto reported finding no evidence of crystalline solution between the compounds. Sindeyeva and Godov-ikov,' in 1959, found very limited crystalline solution. but only under conditions of excess tellurium concentration. Finally Melevski s3 investigation in 1963 indicated that one solid phase exists in the region from PbS to 7 pct PbTe and from 82 pct PbTe to PbTe at 886'C, with an eutectic at 55 pct PbTe at that temperature. Detailed data on the solvus boundary were not given. EXPERIMENTAL EQUIPMENT AND MATERIALS Commercially produced PbTe and PbS powders were used as starting materials. Batches of specific mole percent composition were accurately weighed and mixed in a plastic bottle, in a shaker mill. An analy- sis of impurity content is given in Table I for pure PbS and PbTe and for two randomly selected batches after the powders were mixed. Individual samples, ranging in weight from 0.2 to 0.5 g, were sealed in evacuated silica tubes which had been thoroughly washed and rinsed with acetone and distilled water. Thus all data taken were at the pressure of the system. Subsolidus relations were studied down to 400°C by heating the samples in a vertical tube furnace for 24 hr. The sealed tubes were quenched in water with quench time from the hot zone not exceeding 1 sec. Temperatures were measured by a chromel-alumel thermocouple and controlled to 53°C for most runs. The number and composition of phases present were determined from powder X-ray diffraction patterns taken at room temperature on a Norelco diffractome-ter, using silicon as an external standard. Above 850°C quenching techniques were, in general, found to be unsatisfactory, and differential thermal analysis (D.T.A.) was used to determine melting relations. The evacuated tubes were recessed about 1 cm at one end to accommodate the differential thermocouple. Al203 was used as the reference material in a similar tube containing the other side of the differential couple. For temperature measurements, a separate thermocouple was placed in the recess of the tube containing the sample to be measured, thus providing an opportunity to obtain thermal, as well as differential, analysis. All thermocouples for these measurements were Pt-Pt 10 pct Rh. Temperature and differential curves were recorded separately on synchronized strip-chart recorders. Thermocouples and recording equipment were calibrated using NaCl and gold standards, using the melting points 801" and 1063 C, respectively, which span most of the temperature range of interest. Heating and cooling rates generally were from 4 to 7°C per min. It was found, in fact. that rates ranging from 1.5 to 25°C per min did not significantly change the data obtained.

Jan 1, 1967

By C. E. Coleman, D. Hardie, A. E. Wraith

A photoguaplric method of measuring crack velocities has been applied to an examilzation of- the effect of hydrogen on the impact properties of zirconium. Results indicate that the crack in hydrided zirconit travels at about 26 m per sec whereas that in the uacuum -annealed is dependent on the speed of the hammer. RECENT work on the effect of hydrogen on zirconium reveals that when hydrided zirconium is tested in slow bending the crack producing failure can be unstable. The mode of fracture seems to involve the crack linking up broken hydrides by a ductile mechanism in the zirconium matrix.2" In order to compare the fracture of zirconium with that of other metals which show unstable crack propagation, notably steel, the rate of the crack spread must be known. As the methods previously used for measuring crack growth are either unsuitable for the present work5-'' or very costly," a simple technique has been devised in which the maximum crack velocity is derived from a series of crack position-time measurements. EXPERIMENTAL PROCEDURE The experimental arrangement is shown schematically in Fig. 1. The flash unit12 was triggered when the Charpy hammer touched the specimen and the 6-psec flash of the lamp delayed by a preselected time interval in the range 100psec to 10 msec. The camera was left on open shutter during the test. From direct measurement on a calibrated photographic print, Fig. 2, the position of the crack and the specimen was found at a known time after impact and, from a series of such tests using an appropriate range of flash-delay times, the crack velocity was estimated. Preliminary experiments were carried out on mild steel above and below its transition temperature. Vacuum-annealed zirconium, and zirconium hydrided to 100 ppm H were then tested at 20" and 150°C. For comparison, Zr-2.6 pct Nb alloy (in the 0 + transformed /3 condition), vacuum-annealed or hydrided to 100 ppm H, was tested at 20 C. The chemical analyses of these materials are given in Table I. For the high-temperature tests a fine chromel-alumel thermocouple was spot-welded onto each specimen close to the notch. The test piece was heated up to 200°C to allow enough time for preparing the apparatus while the specimen cooled to the testing tem- perature. It was assumed that the specimen cooled uniformly. The accuracy of the flash-delay time was better than i2 pct i 5 psec. The crack length was taken as its maximum distance traveled normal to the length axis of the specimen. Errors in these measurements arise as a result of the uncertainty in the location of the crack tip and the difficulty in defining the exact position of the crack starting point. The latter was due to the bonding and large amounts of deformation at the hammer contact point, especially in the vacuum-annealed specimens tested at 150°C. The maximum error in the measurements was however estimated to be about 5 pct. DISCUSSION OF RESULTS From the trial experiments using mild steel above its transition temperature it can be seen from the plot of crack length against time after impact, Fig. 3. that a reasonable estimate of the maximum crack velocity at the surface of the specimen may be made. Other features of note are the initiation time before the crack is first seen and the slowing down period

Jan 1, 1967

By C. B. Alcock, M. G. Hocking

The kinetics of the growth of sulfate layers on blocks of Cu20 has been studied between 688" and 800°C. At 788c the over-all weight increases followed the parabolic rate law, with k = 216 30 sq mg per cm4 min, using a 1:1 entering gas mixture of SO2:02. At 757 after an initial linear period the parabolic rate law was followed, with k = 57.8 10 sq mg per cm4 min. The gas mixture required a platinum catalyst to produce the maximum SOs pressure. The sulfation rate at 757' and 788c was high until all the CUZO had changed into a core of CuO, when it became very much lower. At 757°C marker experiments showed that the sulfates (CuO. CuS04 and CuSO4) grow outwards from the oxide surface, but CuO. CuS04 mixed with CuO was found beneath the markers. At 688 markers were found at the CuO. CuS04/CuS04 interface. Visual observations at 757 showed a liquid eutectic moving beneath the sulfate surface. causing very rapid sulfation and extruding to solidify as thick 'needles" up to 8 mm long. Marker experiments have shown conclusi.cely that CuO grows on Cu20 in air by the outward migration of copper. ThermODYNAMIC measurements on the sulfate and basic sulfate of copper, reported recently,' are followed here by measurements of the rates of formation of these sulfates on cuprous oxide, in order to provide a background for the understanding of roasting processes. peretti2 and McCabe and Morgan3 have shown that the phase Cu20 lies next to Cu2S when the sulfide is roasted under conditions where sulfates will be formed. Since this would present too complex a system for kinetic study, the present work4 has been based on the kinetics of sulfation of the oxide phase. The results of a study of the kinetics and mechanism of the sulfation of cobaltous oxide have recently been reported.4,5 Results on the sulfation of cuprous oxide have also appeared,6 but are at variance with those to be reported here. This seems to be because the previous workers6 did not obtain constant SO3 pressures from the SO2/O2 sulfating gas mixtures used, as will be discussed later. Wadsworth, Leiter, Porter, and Lewis found that the sulfates produced when SO2/O2 mixtures are passed over Cu20 at red heats are CuS04 and the basic sulfate CuO.CuSO4. When the decomposition of CuS04 was followed' by differential thermal analysis, a stage corresponding to CuO .CuS04 was reached before decomposition into the oxide occurred. APPARATUS The vertical furnace used for quantitative studies was a conventional resistance-heated and propor- tionately controlled furnace with an even zone (1 deg) which was 4 cm long. The gas mixtures of SO2 and 02 were made by mixing measured flows from capillary flowmeters and drying over phosphorous pentoxide before passing them into the Pyrex top-piece of the furnace assembly. A mullite tube of bore 2% cm was used as reaction vessel and at the bottom of this tube was a trap for SO3, which condensed as a colorless liquid. The residual gas was led into a fume cupboard for ventilation to the atmosphere. The furnace used for visual observations of needle growth and other phenomena consisted of a transparent silica reaction tube of bore 3 cm, having an optically flat silica window sealed into its wall. The reaction tube was clamped vertically, inside a mullite tube of bore 4 cm and length 42 cm which was heated by Kanthal windings. The window in the silica reaction tube was arranged opposite a hole 3 cm wide and 2 cm tall which had been cut in the wall of the mullite winding tube 19 cm from its top end. A binocular microscope was used to look through the window, illumination being provided by a focusing microscope-lamp offset sideways and downwards. The oxide block to be sulfated was suspended from the removable Pyrex top-piece to the reaction tube, by means of which it was inserted at the start of the experiment, and through which entered the S02/02 gas mixture. The variation of the temperature inside the reaction tube with horizontal and vertical displacement from the window was investigated, and, while it can be said that the temperature was constant 1 deg, its value at a given position was known only to 12 deg. In both furnaces, the oxide block to be sulfated was suspended from a small silica hook immediately downstream from a platinum thimble used as catalyst, which was held on a long silica rod from a Pyrex spring attached to the removable Pyrex top-piece of the furnace. The spring was only included in the quantitative sulfating furnace; its sensitivity was 1.4 cm per g and it was found to be free from creep in a 16-hr test when carrying the working load. The extensions were followed by a cathetometer which could be read to 0.001 cm, corresponding to i0.7 mg. Extensions of the spring were measured on adding weights between 5 and 500 mg to the working load (thimble + oxide block), and Hooke's law was closely obeyed. SAMPLES Cuprous oxide blocks were prepared by oxidizing Johnson Matthey "Specpure" copper sheet of 1 mm thickness (impurities: iron at 3 ppm, silver at 2 ppm, lead, nickel, sodium, and silicon each at 1 ppm, calcium, chromium, magnesium, and manganese each at less than 1 ppm) for 6 days in air at 1000°C in a re-crystallized alumina boat. It has been reported7 that when Cu20 is prepared by heating copper sheet for 1 day the central plane of the blocks produced consists

Jan 1, 1967

By D. W. G. White

The surface tension of zinc has been determined by the sessile-drop method in a progvam emphaszzing detailed experimental care. The surface tension oj. the pure metal was measured over a range of ternperature from the melting point (419.6"C) to 540°C. At the melting point, the suvface tension of zinc was found to be: 1) 99.99+ pct Zn - 757.0 5 dynes per cm 2) 99.999+ pct Zn - 761.0 5 dynes per CI 3) 99.9999 pct Zn - 76'7.5 5 dynes pev cna From experiments carried out in a closed, isothermal cell, the temperatuve coejyicient of the surface tension (6y/6T)p, , of zinc xas found not to be negative but to be postiue. A positive tenzperatre coefficient indicates a greater depee of order in the surface than in the body of the lquid. Houlezer, by delibevately inducing continuous zaporization, a temperature coefficient of su)face tension with a negative slope can be produced. The work reported herein was undertaken as part of a larger program of fundamental research on the properties of molten zinc and zinc alloys. This program grew out of a continuing interest at the Mines Branch in the behavior of liquid metals in the foundry and of a desire on the part of the zinc industry for reliable basic data. The work was originally begun in cooperation with the Consolidated Mining and Smelting Co. Ltd., Trail, B.C., and was subsequently continued from 1960 to date in association with the Canadian Zinc and Lead Research Committee and the International Lead and Zinc Research Organization. Although the surface tension of liquid zinc has of course, been measured before, as Table I and Fig. 1 demonstrate, there is not good agreement among the existing values. Such disparities arise because sources of experimental error are insufficiently controlled. This situation places the reader in doubt. One result may be correct within narrow limits—even fortuitously—yet, because there is not agreement between several values, none can be accepted with conviction and all become suspect. It seemed, therefore, in the circumstances, that there was room for further work embodying considerable emphasis on experimental care in order that, within a small margin of error, an accurate value might be obtained. It was in this spirit that the work was undertaken. METHOD The sessile-drop method -as adopted for this work. In this method, when applied to liquid metals at elevated temperatures, the outline of the meridional section through a drop resting freely on a horizontal surface is recorded photographically. Certain parameters

Jan 1, 1967

By T. F. Archbold, P. G. McCormick

Silica fiber 11arkevs and hardness irzdentatiozs have been used to study the thermal diffusion of racancies in zinc placed in temperature gradients of 460o and 706oK per Cm All markers mored toward the higher temperatures, and the data show that the heat of trarlsport Q is greater than the eizthalpy of z,acancj3 forrjalion E by an amount equal to 3.5 kcal per mole. These results ore not in agreement with those obtained in either of the two previous studies with zinc. The problem is discussed in terms of experimental differences and racancy source and sink efficiencies. THE general interest in thermal-diffusion phenomena over the past several years has prompted a number of marker movement studies using pure metals. In order to understand better the relationships between thermal and mass flow, a general goal of the experiments has been to obtain values for the net enthalpies carried by the diffusing atoms. For self-diffusion by means of the vacancy mechanism, the determination of relative marker positions before and after an anneal in a temperature gradient permits a calculation of a value for (Q - Ef). Q is the transferred enthalpy, and Ef is the enthalpy of vacancy formation in the metal being investigated. The initial experimental study of thermal diffusion in pure metals was accomplished by Shewmon who found essentially no movement of surface-hardness indentation markers in single and bicrystals of zinc held for 20 days in a temperature gradient of 310°C per

Jan 1, 1967

By A. C. Losekamp, J. B. Conway

Thermal-expansion data for, tungsten, rhenium, tantalum, .molybdenum, niobium, W-25 pct Re, Ta-10 pct W, ant1 Mo-50 pct Re are presented covering the range from room tempature to 2500°C. In these measureMents, made in a resistively heated tungsten tube furnace operating in a helium atmosphere, data for rod and sheet specimens were found to be identical; in addition, arc-cast and sintered tungsten were found to yield essentially identical results. Optical rneasurenlents of thermal expansion .made in any atmosphere other- than vacuum are subject to a refraction error which can be quite substantial. Specimens tested in helium appear shorter than when tested in racuum and hence a special correction factor must be applied to the helium data in order to obtain accurate results. WHILE it is true that linear thermal-expansion data for many of the refractory metals have been measured to very high temperatures, it is also true that except in a few instances the data from various investigators are not in good agreement. This is particularly evident in the case of tantalum and niobium although some tungsten data have been reported which differ by as much as 40 pct from the data of other investigators. Due to the sensitivity of both tantalum and niobium with respect to impurity absorption during exposure to high temperatures, it is probable that this single factor accounts for the majority of the discrepancies in the thermal-expansion data for these metals. However, this same factor can probably not be employed to explain the existing differences in the tungsten data. In all probability, these are due to errors in the measurement technique, to material composition variations, or to changes which take place in the material during the heating process (e.g., additional densifica-tion resulting from heating a sintered specimen above the original sintering temperature). In view of the discrepancies which exist in the linear expansion data reported for many of the refractory metals, the current study was initiated in an attempt to resolve such differences. Also, no high-temperature linear thermal-expansion data were found to be available for several refractory metals. Providing such data was another objective of the current investigation. MATERIALS In this study test specimens were employed in either rod or sheet form and in several instances both arc-cast and sintered material were employed. Material compositions are presented in Table I. Helium gas was fed to the furnace at a rate of about 0.5 SCFH and no special purification procedures were employed. However, the helium contained less than 50

Jan 1, 1967

By R. G. Garlick, M. Garfinkle

It was observed for several bcc metal crystals that the Knoop hardness anisotropy was dependent essentially on the direction of the lung axis of the indentor alone and not on the plane of indentation. The generality of this observation was tested for an fcc md an hcp metal and an ionic crystal. For cubic crystals, this observation was valid; for the hcp structure, however, the planes of indentation did have an effect on the hardness anisotropy, although this was not nearly as significant as the direction of indentation. Because the direction of indentation is the only significant crystal-lographic parameter necessary to describe the hardness anisotropy, it is possible to represent the anisotropy of single crystals on the standard stereographic triangle. THE commonly observed1, 2 periodic variation of indentation hardness with crystallographic direction on the high-symmetry planes of various single crystals has been inadequately related to the physical or mechanical properties of the crystals examined. In fact, the hardness anisotropy curves for the various planes of a particular metal crystal, as is illustrated in Fig. 1, are uncorrelated and appear in the literature3, 4 as unrelated observations. Attempts to correlate hardness anisotropy curves with specific physical properties can be generally divided into either mechanistic or nonmechanistic approaches. A nonmechanistic approach would be to devise a mathematical expression that could describe the various hardness anisotropy curves. Such a relation could then be compared with the known anisotropy of various physical properties to determine which contribute to the observed hardness anisotropy. No such mathematical expression has been found in the literature.

Jan 1, 1969

By Matti J. Saarivirta

The relative machinabilities of the precipitation-hardenable Cu-0.9 pct Cr, Cu-0.25 pct Zr, and Cu-0.9 pct Cr-0.25 pct Zr alloys are improved from 18 to 80 pct by 0.75 to 1.25 pct Pb. The Lead also improves the tensile strength, hardness, ad resistance to softening of the Cu-Cr and Cu-Cr-Zr alloys. When the alloy containing 0.7 to 2.2 pct Cr, 0.10 to 0.25 pct Zr, 0.75 to 1.25 pct Pb, and balance copper is solution-annealed at 1000°C (1830°F) and then aged at 525°C (Y75°F), tensile strength of 65,000 psi, 16 pct elongation, 62Rb hardness, and 84 to 87pct IACS electrical conductivity are obtained. The copper base Cu-Cr, Cu-Zr, and Cu-Cr-Zr alloys have high electrical and thermal conductivities, high strength and resistance to softening at elevated temperatures, but their machinability is poor, i.e., close to that of the pure copper. In the manufacture of various components such as welding electrodes or electrical and thermal conductors it is ofter desirable that the alloy have good machinability for high production rates and long tool life. Thus, alloys that combine these properties may be used not only for existing applications, but for new ones where good machinability is a requirement. This investigation was undertaken to improve machinability without impairing other desirable characteristics of the Cu-Cr, Cu-Zr, and Cu-Cr-Zr alloys. These commercial alloys contain about 0.4 to 1.2 pct Cr, 0.10 to 0.25 pct Zr, and balance copper. Lead was selected as an element that should improve the machinability and possibly other characteristics of the alloy. WORK PROCEDURE This investigation began with a study of the effect of lead on the hardness, tensile strength, electrical conductivity, and machinability of the binary alloy containing 0.10 to 1.30 pct Cr and balance copper. This was followed by an investigation of the effect of lead on the Cu-0.1 to 0.4 pct Zr and Cu-Cr-Zr alloys. The alloys were made from initially oxygen-free copper and for comparison some castings were made from phosphorus-deoxidized Lake Copper. Commercially pure chromium, zirconium, and lead were used for alloying. In melting the chromium was added to molten copper at 1400°C (2550°F), the heat held for 15 min at temperature, and the temperature then lowered to 1350°C (2460°F) when the other elements were added. The alloys were held for 15 min at this temperature and cast into a cast-iron mold. One-kilogram, 3-in.-diam castings were made. An argon cover was maintained during melting and casting to prevent oxidation. The chemical compositions of the alloys are shown in Table I. The micro structure and properties of the alloys were studied in the cast and wrought conditions prior to and after various solution-annealing and heat-treating cycles. The relative machinability was determined as a function of the lead content and compared with the free-machining Cu-lpct Pb alloy. To determine the machinability, 13/16-in.-diam cast specimens were cut by a machine hack saw using a constant cutting speed of 50 fpm, a fixed feed force, and a new blade for each alloy specimen. Molybdenum highspeed steel saw blades, 0.032 in. thick with 14 teeth per in., were used in all tests. No cutting fluid was used. Five tests were made on each specimen and the average elapsed time per test was taken as a measure of the relative machinability for that alloy. The variation of cutting time for each alloy was less than 110 pct.

Jan 1, 1969

By K. A. Gschneidner, O. D. McMasters, T. J. O’Keefe

X-ray diffraction, differential thermal, ad rnetallo-graphic methods were used to establish the Dy-Pb Phase diagram. Lead additions lower the 1377°C transformation temperature of dysprosium to 1360°C leading to an inverted peritectic reaction. The 327°C melting point of lead is lowered by dysprosium additions to about 326°C yielding a eutectic reaction. A second eutectic reaction occurs at 13.3 at. pct Pb and 1200°C. The dysprosium-richest intermetallic compound DysPb3 melts congruently at 1695°C and crystallizes in the hexagonal Mn5Si3 (D8,) type structure. The peritectic decomposition temperatures for the remaining compounds are Dy5Pb, at 1555C, DyPb2 at 955C, and DyPb3 at 880°C. A fifth compound near the DyPb stoichiometry exists over a 310°C temperature range decomposing at 1130°C by means of an inverted peritectic reaction and melting incongruently at 1440°C. The crystal structures of the compounds are discussed. A systematic study of the rare earth-lead alloy systems is underway in an effort to supply information concerning the alloying behavior of the rare earth metals. The Dy-Pb phase diagram is the fourth system to be investigated in this study. The Yb-Pb,1 Y-Pb,2 and Eu-Pb 3 diagrams have been published recently. Utilization of the rare earth series of metals as a research tool in this manner should yield a better understanding of alloy formation. EXPERIMENTAL PROCEDURE Materials. The lead used in this investigation was obtained from Cominco Products, Inc., and was specified to be 99.99 pct pure. The dysprosium was prepared in this Laboratory by the calcium reduction of the fluoride followed by distillation of the dysprosium. The major impurities in the dysprosium in ppm are: A1 (<40), Ca (400), Er (<50), Gd (<200), Ho (<200), Mg (<50), Si (30), Ta (400), Tb (<100), Y (<50), 0 (651, H (15), N (not detected), F (430), C (35). Alloy Preparation. Most of the alloys were prepared by melting weighed amounts of dysprosium and lead in sealed tantalum crucibles. The tantalum crucibles were sealed by are-welding in a He-Ar atmosphere welding chamber. Thus the alloys are in contact with He-Ar at about 1 atm pressure. Homogenization was achieved by holding them in the liquid state for about 1 hr, cooling, inverting the crucibles, remelting, and repeating the process at least twice. Since these alloys were prepared in sealed tantalum crucibles, chemical analysis for final composition was thought to be unnecessary. No detectable reaction of these alloys with the tantalum crucible was observed by metallographic examination. Metallographic evidence was also used to confirm the homogeneity of some of the alloys prepared in this manner. The compositions of a few alloys, which were prepared by nonconsum-able are-melting, were corrected for the small weight losses involved by assuming that the weight loss is due to vaporization of lead. The specimens obtained from the alloy samples were prepared under a dry-argon atmosphere because they were rapidly attacked by air and moisture. Thermal Analysis. Differential thermal analysis methods were used to determine the liquidus curves and reaction horizontals of the system. Both Pt vs Pt + 13 pct Rh and W + 5 pct Re vs W + 26 pct Re thermocouples were used to measure the temperature. An X- Y recorder was used to record the specimen temperature and differential electromotive force between the specimen and molybdenum standard. The arrest temperatures were measured potentiometri-cally. The accuracy limits (* values) associated with the reaction temperatures obtained by this method were estimated on the basis of both the reproducibility of the particular temperature value and the accuracy of the thermocouple at a given temperature. Liquidus temperatures were obtained from cooling arrest data while both heating and cooling arrest data were used to establish the horizontals of the diagram. Heat treatments during the thermal analyses of the alloys between 40 and 70 at. pct Pb were necessary in order to approach equilibrium conditions. The samples were held at temperatures between the various peritectic horizontals for l to 2 hr before the thermal analyses were continued. The entire range of compositions was investigated at the expense of a minimum amount of materials by adding appropriate amounts of lead to master alloys. More than sixty alloys were analyzed by this differential thermal method and for each alloy the results given herein are taken from two or three heating and cooling cycles. X-Ray and Metallographic Methods. Slice specimens for metallography and powder specimens for X-ray diffraction were prepared from rod-shaped samples which had been melted in sealed 0.62 5-cm-diam tantalum crucibles. The specimens were heat-treated in sealed tantalum crucibles which were protected by sealing them in argon-filled quartz ampules. Quenching was accomplished by breaking the ampules in ice water after heat treatment. X-ray powder specimens were sealed in 0.3-mm-diam glass capillaries under a dry-argon atmosphere. Copper, iron, and chromium radiation were used to obtain the powder patterns for these alloys. More than 150 powder patterns were obtained for specimens of various compositions and heat treatments. Included in these were several patterns for specimens which had purposely been oxidized. Patterns from specimens which had been accidentally exposed

Jan 1, 1969

By R. K. Buhr, H. Thresh, M. Bergeron, F. Weinberg

The microsegregation of nickel and chromium in directionally solidified AISI 4340 steel castings has been measured using electron probe microanalysis. Minimum concentrations were observed to occur at the center of the dendrite stalks, as reported previously. However, the position of the maximum concentrations could not be determined from the dendrite configuration. An etching technique has been developed which shows the position of maximum concentration. Measurements were made of the distribution of nickel and chromium in the dendritic structure. The ratio of maximum to minimum concentration was determined as a function of primary dendrite arm spacing for both as-cast and partially homogenized materials. The results are compared with observations reported in the literatuve. A S part of an investigation of solute segregation in directionally solidified AISI 4340 steel casting, electron probe microanalysis was used to measure the distribution of nickel and chromium in the dendritically segregated material. This complemented the observations on the segregation of radioactive phosphorus obtained by autoradiographic techniques in the same castings.&apos; Kattamis and I?lemings2 have reported similar measurements, using electron probe microanalysis, on dendritically segregated AISI 4340 steels. They found minimum solute concentrations occurred at the center of dendrites, maximum concentrations occurred in the center of interdendritic regions, for symmetrically oriented dendrites, and a regular variation of concentration within dendrite arms. The ratio of maximum to minimum concentration was found to be essentially independent of position in the castings, except near the chill surface where it was somewhat higher. Assuming complete diffusion in the liquid and no diffusion in the solid during freezing, they considered that isoconcentration curves in the steel were homothetic. As a result, isoconcentration curves of the various elements, contour surfaces of dendrites produced by isothermal-transformation studies, and the contour of the solid-liquid interface would all be similar, and could be superimposed by a uniform expansion or contraction of the contours. Preliminary results of the present investigation suggested that isoconcentration curves were not homothetic. It was also evident that points of maximum concentration could not be predicted from the dendrite configuration. Since the ratio of maximum to minimum concentration appeared to be an important parameter in defining the overall segregation in a casting, other techniques for determining the point of maximum concentration were investigated. In addition the overall solute distribution associated with the dendritic structure was examined for both nickel and chromium, and the consistency of the distribution for neighboring dendrites was determined. METHOD Fifty-pound heats of AISI 4340 steel were cast in a manner similar to that used by Flemings et al3 with a water-cooled copper base plate and exothermic sides and top. The nominal composition of the material was C, 0.41 pct; Mn, 0.66; Si, 0.35; S, 0.012; P, 0.010; Ni, 1.88; Cr, 0.95; Mo, 0.28. The steel solidified directionally from the chill surface, with a dendritic structure which increased in dendrite arm spacing with increased distance from the chill. Results of the general investigation of the cast structure and segregation of radioactive phosphorus in these castings have been reported elsewhere.&apos; For the present measurements, sections were cut from the casting at several distances from the chill surface. The sections were subsequently heat-treated, mounted, and then polished on a plane perpendicular to the general freezing direction of the casting. Electron probe microanalysis was carried out with the JEOL-JXA3 microprobe using a voltage of 25 kev and beam current of 0.15 µa. The take-off angle is 22 deg. Quartz crystals were used in the spectrometers and measurements made for Ka radiation from both nickel and chromium simultaneously. A thin layer of carbon was deposited on all specimen surfaces prior to examination in the microprobe. Early measurements were made on polished surfaces, with indentation marks produced by a hardness tester to indicate the area of interest. It was found desirable to use etched surfaces, as opposed to polished surfaces, to reduce sample preparation time and more readily relate the microprobe scan to the structure. To determine if this could be done, without introducing significant errors, a series of measurements were made on polished and etched surfaces of the same specimen. Both polished and etched surfaces produced similar results within normal scatter as shown in the observations. Subsequent measurements were then made on etched surfaces. Measurements with the microprobe analyzer were made by point counting, for periods of 100 sec, at 10-µ intervals. Ten-second counts were made on pure nickel and chromium standards, incorporated in the specimen mount before and after each set of measurements. The results were adjusted for background, then corrected for dead time using the expression:

Jan 1, 1969

By V. Koump, T. F. Perzak, R. G. Olsson

The rate of dissolution of recrystallized alumina in molten iron oxide in equilibrium with iron at 1450°C was studied by rotating alumina disks in the melt. The samples were rotated from 1 to 12 min at speeds from 54 to 3270 rpm. It is concluded from the experimental results that the process is limited by diffusion in the liquid boundary layer. The interdiffusion coefficient for the dissolution of alumina disks in pure molten iron oxide was estimated to be about 3 xl0-5= sq cm per sec. THE erosion of refractory materials is of considerable importance in iron- and steelmaking processes. Since many refractories contain alumina, this investigation was undertaken to develop a further understanding of the erosion mechanism. Shurygin et al.1-3 have investigated the rate of dissolution of alumina in molten silicates and molten fluorides by rotating alumina disks in various melts. The rates were reported to be limited by diffusion in the liquid boundary layer. In the present investigation the rate of dissolution of alumina in molten iron oxide in equilibrium with iron was studied in a similar manner; alumina disks were rotated at different speeds in molten iron oxide at 1450°C. The relationship between the rate of dissolution of the flat surface of the disk and the speed of rotation was used to determine whether the process is limited by diffusion in the liquid boundary layer or by some chemical reaction mechanism. APPARATUS AND EXPERIMENTAL PROCEDURE A schematic diagram of the experimental apparatus is shown in Fig. 1. The iron oxide melts were contained in 2-in.-diam high-purity iron crucibles that were centered in a cylindrical graphite susceptor. Prior to each sequence of experiments, sufficient reagent-grade ferric oxide was added to a crucible to form approximately 350 g of molten iron oxide; the depth of the melt was about 11/2 in. To prevent excessive erosion of the crucible, about 70 pct of the required iron was added to the crucible in the form of iron powder. The mixture was melted in an atmosphere of purified argon by induction heating with a 250-kc generator. After the oxide was molten, a Pt/Pt-10 pct Rh thermocouple at the exterior of the crucible was calibrated against an iron-sheathed thermocouple immersed in the melt and was thereafter used to regulate the melt temperature. All experiments were conducted at 1450°C with a probable error of 10°C. The alumina disks were constructed from pure re-crystallized alumina having a density of 3.7 g per cu cm (porosity approximately 6 pct). For each disk sample a 1-cm-diam alumina cylinder of known length (0.9 to 1.0 cm) was cemented into a ground seat at the end of a 1.27-cm-OD centerless ground alumina tube. The ends of the tube and cylinder were flush and served as the disk surface. When mounted in the apparatus the alumina tube was guided by tungsten carbide bearings and rotated by a variable-speed motor. The bearing and drive assembly could be raised and lowered in order to allow the sample to be quickly moved in and out of the melt. At the start of an experiment, a sample was preheated for several minutes directly above the melt, and then immersed in the middle of the melt to a depth of a in. and rotated for 1 to 12 min at speeds of 64 to 3270 rpm. The speed of rotation was measured by a hand tachometer. At the start and completion of each experiment, a melt sample was withdrawn with a cold copper rod and the alumina content was determined by chemical analysis. During individual experiments the alumina concentration of the melt changed by the order of 0.25 wt pct. Average melt compositions for individual experiments were used in the subsequent computations and were in the range between 0.12 and 4.3 wt pct alumina. The extent of dissolution was determined by sectioning the end of the sample and measuring the final length of the alumina cylinder with a microscope. Since the exposed end of the cylinder, i.e., the disk surface, was etched in a manner characteristic of this geometry, a number of measurements were made on

Jan 1, 1969

By Shiro Ban-ya, John Chipman

Equilibrium in the reaction was investigated at temperatures of 1500°, 1550°, and 1600°C for sulfur concentrations up to 7.2 wt pct. Multisample crucibles contained the liquid alloys in a resistance-heated furnace using a technique especially designed for the study of more complex alloys to be reported separately. Modern free-energy data are used to correct the H2S:H2 ratio for dissociation of H2S and calculalion of the partial pressure of S2. Published data on the equilibrium are similarly corrected. Thermodynanzic treatment of the data employs the composition variable zs = nS/(nFe — nS) and the activity coefficient Gs = as/zs The data at 1500" and 1550°C are fitted by the equation log s = —2.30zs. Within the limits of experimental error the same coefficient is applicable to the data at higher temperatures. Equations are given for the free-energy change in Reaction [I] as well as for the solution of S, gas in the metal. The heat of solution of 1/2 s2 is -32.28 i2.5 kcal. Uncertainty in the free energy is very much smaller. For dilute solutions of interest in steelmaking, the activity coefficient of sulfur is unchanged from that listed in Basic Open Hearth Steel-making. DETERMINATIONS of the thermodynamic properties of sulfur in liquid iron by Morris and williams1 and by Sherman, Elvander, and chipman&apos; provided a basis for control of sulfur in steelmaking processes. From the standpoint of understanding the chemistry of metal plus nonmetal in liquid solution they left several questions unanswered. The activity of sulfur in dilute solution at about 1600°C was well-established but temperature coefficients were uncertain, due at least in part to the use of the optical pyrometer and uncertainty regarding the effect of sulfur on emissivity. It appeared that deviation from Henry&apos;s law increased with increasing temperature, a most unusual behavior requiring either confirmation or disproof. These studies were based on experimental determination of equilibrium in the reaction: At high temperatures H2S is partially dissociated so that the gas mixture contains HS, S2, and S in addition to HS. At the time of the earlier studies the free energies of these constituents were unknown and it was therefore impossible to make adequate correction for dissociation. Observations on the effects of alloying elements by Morris and coworkers1, 3 and by Sherman and Chip-man4 enable us to assess the effects of alloying elements on the activity and to make corrections for incidental impurities in the binary liquid. These studies as well as a number of more recent investigations will be reviewed in detail after out own experimental results have been presented. It was our purpose in planning this study to avoid uncertainties regarding the emissivity of alloys and the errors of thermal diffusion which plagued some of the early attempts,5 by using a resistance furnace and thermocouple in preference to induction heating and optical pyrometer. Modern data on free energies of the gaseous species are to be applied to our data and to those of other investigators to obtain corrected values of K1 and of the activity coefficient and ultimately to relate the sulfur content of the bath to the equilibrium partial pressure of S,. Extension of the study to include ternary and complex solutions will be described in a later section. EXPERIMENTAL METHOD a) Preparation and Calibration of H2-H2s Gas Mixture. The source of hydrogen sulfide was a preparer mixture of 43 pct H2S, balance hydrogen, contained in a large aluminum cylinder. This was passed through anhydrone and through a microflowmeter. Hydrogen was passed through platinized asbestos, ascar-ite, and anhydrone, and through a capillary flowmeter. Argon was passed through copper wool at 500°C, then through ascarite, anhydrone, and a flowmeter. The flow rate of hydrogen was kept constant at 200 ml per min, to which an arbitrary amount of the hydrogen-hydrogen sulfide mixture was constantly added and then the prepared gas mixture was introduced into the reaction tube through a gas mixer. In certain experiments 200 ml per min of argon was added to the hydrogen-hydrogen sulfide gas mixture to increase the total flow rate of gas. The ratio of hydrogen-hydrogen sulfide in the inlet gas was checked for each run by chemical analysis. A sample of the gas taken from a bypass was bubbled through zinc and cadmium acetate solution (4 pct zinc acetate, 1 pct cadmium acetate, and 1 pct acetic acid) to remove hydrogen sulfide from the gas mixture, and the flow rate of the remaining hydrogen was measured by a soap bubble method to determine the volume of hydrogen. The amount of hydrogen sulfide absorbed in solution was determined by titration with iodine against sodium thiosulfate, with starch used as the indicator. The ratio of hydrogen sulfide to hydrogen in the inlet gas could be kept within ±2 pct in the range from 10-2 to 5 x 10"4 which corresponds to from 0.2 to 7.0 wt pct sulfur in liquid iron. b) Furnace Arrangement. Fig. 1 shows the furnace arrangement and the shape of the alumina crucible used in this experiment. A vertical-tube silicon carbide electric resistance furnace contained the reaction tube which consisted of two parts, the gas-tight

Jan 1, 1969

By Charles E. Lundin

Pressure-temperature-composition data were obtainedfor the Er-H system. Measurements werecar-ried out in the temperature range of 473° to 1223°K, the composition range of erbium to ErH,, and the pressure range of 10-5 to 760 Torr. Solubility relationships were established from these data throughout the system. Three solid-solution phases were delineated: metal solid solution, dihydride phase, and trihydride phase. The trihydride Phase decomposes at about 656°K and 1 atm pressure. The dihydride phase is stable to about 1023°K, but becomes more deficient in hydrogen above this temperature. The equilibrium decomposition pressure-temperature relationships in the two-phase regions, erbium solid solution plus dihydride and dihydride plus trihydride, were deter- The differential heats of reaction in these two regions are AH = - 52.6 * 0.3 and - 19.8 i 0.2 kcal per mole of Hz, respectively. The differential entropies of reaction are AS = - 35.2 * 0.3 and - 30.1 * 0.4 cal per mole HZ.deg, respectively. Relative partial molal and integral thermodynamic quuntities were calculated in the system to the dihydride phase. RARE earth metal-hydrogen systems have been the subject of general survey,1"4 and all have been found to form hydride phases. The heavy rare earths, of which erbium is a member, form dihydride and trihydride phases with different crystal structures, whereas the light rare earths form only a single-phase dihydride which expands without structure change, as hydrogen is added, to the trihydride composition. These materials are of interest primarily because of their theoretical properties, such as bonding, defect structure, and thermodynamic and electronic characteristics. Erbium has been studied in several previous investigations.5, 6 It was deemed desirable to more thoroughly and accurately define the system, both for the phase equilibria and the thermodynamic properties. I) EXPERIMENTAL PROCEDURE A Sieverts&apos; apparatus was employed to conduct the experimental measurements. Briefly, it consisted of a source of pure hydrogen, a precision gas-measuring buret, a heated reaction chamber, a mercury manometer, and two McLeod gages (a CVC, GM 100A and CVC, GM 110). Pure hydrogen was obtained by passing hydrogen through a heated Pd-Ag thimble. The hydrogen was analyzed and found to have only a trace of oxygen and nitrogen. A 100-ml precision gas buret graduated to 0.1-ml divisions was used to measure and admit hydrogen to the reaction chamber. The reaction unit consisted of a quartz tube surrounded by a nichrome-wound furnace. The furnace temperature was controlled by a recorder-controller to ±1°K. An independent measurement of the sample temperature in the quartz tube was made by means of a chromel-alumel thermocouple situated outside, but adjacent to, the quartz tube near the specimen. Pressure in the manometer range was measured to ±0.5 Torr and in the McLeod range (10-4 to 10 Torr) to ±3 pct. The hydrogen compositions in erbium were calculated in terms of hydrogen-to-erbium atomic ratio. These compositions were estimated to be ±0.01 H/Er. The erbium metal was obtained from the Lunex Co. in the form of sponge. The metal was nuclear grade with a purity of 99.9 pct +. The oxygen content was reported to be 340 ppm and the nitrogen not detectable. Metallographically the structure was almost free of second phase (<1 vol pct). A quantity of sponge was arc-melted for use as charge material. The solid material was compared with the sponge in the pressure-temperature-composition relationships. They were found to be identical. Therefore, sponge material was used henceforth, so that equilibrium could be attained more rapidly. The specimen size was about 0.2 grain for each loading of the reaction chamber. The procedure employed to obtain the pressure-temperature-composition data was to develop experimentally a family of isothermal curves of composition vs pressure. First, a specimen of erbium was wrapped in a tungsten foil capsule to prevent contact with the quartz tube. After loading the specimen, the system was evacuated to less than l0-6 Torr, flushed several times with high-purity hydrogen, and evacuated again ready for the start of the experiment. The furnace was then brought to the desired temperature. A measured amount of hydrogen was admitted into the chamber. Equilibrium was allowed to be attained, the pressure read, and the process then repeated many times until 1 atm of gas pressure was finally reached. Other isotherms were then developed in the same manner. The partial pressure plateaus were determined by another manner. In the solid solution-dihydride region a composition of approximately 1.0 H/Er was selected on the plateau. The temperature was varied throughout the range of interest. At each temperature level, equilibrium was achieved, the pressure read, and the next temperature attained. The temperature was cycled both up and down. In the dihydride-trihy-dride region, the plateaus were determined in the 473" to 651°K range only by heating to the desired temperature and not by both heating and cooling. The data were much more reproducible in this manner. Equilibrium required long periods of time. Specimens were initially hydrided to 2.8 H/Er, so that at the higher

Jan 1, 1969

By J. W. Martin, L. K. Singhal

Grain boundary M23CB precipitates have been shown to form by a process involving the migration of an austenite grain boundary, and each plate of precipitate is in parallel orientation with one of the austenite grains constituting the boundary. The carbide distribution and morphology appear to be sensitive to grain boundary mis orientation. Some areas of austenite grain bowzdary permit the development of an array of M,C, particles, some of which are in parallel orientation with one grain and some with the other grain constituting the boundary. Massive carbide at grain boundary triple points is also shown to be in parallel orientation with one constituent grain. PREFERENTIAL precipitation during aging of carbides of the type (Fe,Cr)23C6, usually written MZ3C6, in grain boundaries of quenched austenitic stainless steels has been widely recognized. M23C6 has a complex cubic crystal structure&apos; which contains ninety-two metal atoms and twenty-four carbon atoms per unit cell. Less energy is involved in forming grain boundary precipitates than in the formation of intragranular precipitates, and the process is further enhanced by the accelerated diffusion rates in the boundaries and by the probability of segregation of chromium atoms and carbon atoms to the region of the grain boundaries during prior solution heat treatment in order to reduce lattice strain. Early electron micrographic studies2, 3 involving either extraction replica or normal replica techniques established the geometric or dendritic form of the carbide particles, although this approach led to dis- pute as to whether the particles grew within the plane of the boundary or grew into the matrix.4-6 More recent thin-foil studies&apos; have claimed to identify a discontinuous precipitation process involving M23C6 at grain boundaries, and the object of the present work was to attempt to clarify the situation using modern electron micrographic and diffraction techniques. 1) EXPERIMENTAL 1.1) Material. The steel selected for this work had a base composition of 24 pct Ni-25 pct Cr-3 pct Ti and contained about 0.04 pct C. The full analysis if given in Table I. This alloy was in the form of strip which had been hot- and cold-rolled to a thickness of 0.6 mm. 1.2) Heat Treatment. Specimens 4 cm long by 1 cm wide were solution-heat-treated for 3 hr in argon at 1150°C, followed by water-quenching. Specimens were subsequently aged in vacuo at 750°C for periods up to 500 hr. 1.3) Preparation of Electron Microscope Specimens. The heat-treated strips were cut bv spark machining into discs of 3 mm diam and 0.6 mm thickness. he-discs were dished on both sides using an electrolytic jet of 15 pct HCl electrolyte at 80 v. Final electro-polishing of the discs was carried out using 10 pct perchloric acid, 20 pct glycerol, and 70 pct ethanol at 10 v. The current density was kept below 300 ma. cm"2 by cooling the electrolyte to 0" to 5°C. As soon as a small hole appeared, the electropolishing was stopped and the specimen was quickly washed with ethanol.

Jan 1, 1969

By N. A. D. Parlee, I. D. Shah

The solubilities of oxygen in liquid Ag-Au, Ag-Pt, and Ag-Pd alloys have been determined in the range of 940° to 1200°C at 1 atm pressure of oxygen using an improved Sieverts technique. The additions of gold (0 to 57 pct), platinum (0 to 27 pct), and palladium (0 to 22 pct) to liquid silver continuously decrease the solubility of oxygen in liquid silver. Activity coefficients and interaction coefficients of oxygen in these alloys and have been calculated. The interaction coefficientscan be described by the following equations: Approximate second-order interaction coefficients (pM have been calculated. The contribution of the product, pMxNM, to In yo only becomes significant at high alloy concentrations. RECENTLY several investigators1"3 have redeter-mined the solubility of oxygen in liquid silver. In general the recent findings1" for Po, = 1 atm are in good agreement with the equation:4 log %O = 695.4/T + 1.086 [1] It is established1, 2 that the solubility of oxygen follows Sieverts&apos; law reasonably well, at least up to 1 atm partial pressure of oxygen. It should be noted that a very slight deviation from Sieverts&apos; law has been reported by Lupis and Elliott.3 Only recently has the solubility of oxygen in Ag-X binary liquid systems received much attention, and only the Ag-Cu, Ag-Au, Ag-Pt, and Ag-Pd systems have been studied. Par lee, Sacris, and zoellners reported that the solubility of oxygen in liquid silver increases progressively with the small additions of copper (0 to 0.5 pct) up to the point where the copper oxide phase appears. Lupis and ~lliott~ have reported that the solubilities of oxygen in liquid silver decrease progressively with the additions of gold, platinum, and palladium. However, their investigation was limited to 0 to 5 pct of these alloying elements, a range too limited to satisfy the requirements of the research program of this laboratory, where the solubilities of oxygen in the range of 0 to 30 pct were required for the calculation of chemical diffusion coefficients of oxygen in these alloys. The present paper deals only with the solubilities of oxygen in these alloys while another paper will deal with the diffusion of oxygen in these alloys. EXPERIMENTAL METHOD A Sieverts technique was employed which involved an improved design of the reaction tube, Fig. 1, as described briefly in a previous communication.4 Liquid melts (70 to 100 g) were held in Norton Alun-dum crucibles. The induction furnace used had a maximum output of 2.5 kw with very fine control. This induction system had excellent stability and the final equilibrium temperatures measured by calibrated Pt-Pt, 10 pct Rh thermocouples are believed to be within ±2C. These thermocouples were checked against the melting point of pure gold wire, and the results agreed with standard tables (±l°C). Each run involved a careful sequence of operations. The sample was heated to and held at about 900°C in vacuum for 3 to 4 hr with the thermocouple in a retracted position. After melting, the melts were usually exposed to a small amount of oxygen (0.5 to 2.0 cu cm) and then degassed slowly for 1 to 2 min to remove any oxidizable volatile impurities such as carbon and sulfur as CO, CO2, SO2, and SO forth. Argon gas was then allowed to enter the system. The protection tube containing the thermocouple was then

Jan 1, 1969

By T. W. Watson, D. R. Flynn

Measurements have been made of the thermal conductivity and electrical resistivity of two specimens of 0.005-cm (2-mil) Be-Cufoil over the temperature range -140° to +200°C. The thermal cmductivity of Be-Cu Alloy 125 was found to be significantly higher than that of Alloy 25, which had a higher impurity content. The thermal conductivity and electrical resistivity values obtained were in concordance with the Smith and Palmer relation for copper alloys which states that ? = 0.0239 (T/p) + 0.075 where A is thermal conductivity (W cm-&apos; deg-&apos;), p is electrical resistivity (microhm-cm), and T is absolute temperature (OK) , indicating that the Smith and Palmer relation can be used to predict the thermal conductivity of this type of Be-Cu alloy over the temperature range -140" to + 200°C to within an accuracy suitable for most engineering applications. THE National Aeronautics and Space Administration, Goddard Space Flight Center, Greenbelt, Md., requested the National Bureau of Standards to measure the thermal conductivity of 0.005-cm Be-Cu foil which was to be used to fabricate antennae for use in Radio Astronomy Explorer space craft. It was felt that measurements had to be made on the actual antenna material, rather than on a thick bar of similar material, since the cold-working and age-hardening properties of the alloy would make it very difficult, if not impossible, to place a thick bar in the same metallurgical state as the 0.005-cm material. As discussed in Section 111 of this paper, the thermal conductivity of many copper alloys can be computed rather accurately from electrical resistivity data using an empirical relation developed by Smith and palmer&apos; and further confirmed by owell.&apos; However, there has been very little work done on correlating thermal and electrical conductivities on Be-Cu alloys. We were reluctant to assume the validity of the Smith-Palmer relation on Be-Cu alloys because of the very large mass difference between beryllium and copper. As will be seen, however, our experimental results indicate that the Smith-Palmer relation is valid for the two alloys on which we made measurements. I) DESCRIPTION OF SAMPLES Samples of Be-Cu Alloy 25 and Be-Cu Alloy 125 were furnished to NBS in the form of rolled strip material, 0.005 cm thick by 5.08 cm wide. The Be-Cu Alloy 25 was purchased by NBS in the form of a continuous length of flat strip. The Be-Cu Alloy 125 was furnished to NBS by Goddard Space Flight Center in the form of two lengths of strip that had been formed into "tubing" of about 1.2 cm diam, with one side of the strip overlapping (but not connected to) the other side by about 90 deg. This "tubing" had been opened up to be flat and then rolled onto spools of about 3 cm diam. When unrolled, the strip would spring back into tubular form. Samples of both of the Be-Cu alloys were chemically analyzed by the NBS Analytical Chemistry Division. The beryllium content was determined quantitatively by the phosphate-gravimetric method to be 1.83 wt pct for Alloy 25 and 1.80 wt pct for Alloy 125. The two alloys were also examined by a general qualitative spectrochemical method for metallic elements. The Alloy 25 specimen contained between 0.1 and 1.0 wt pct Al, Co, Fe, and Si and between 0.01 and 0.1 pct Ni. The Alloy 125 specimen contained between 0.1 and 1.0 pct Co and between 0.01 and 0.1 pct Al, Fe, and Si. Other metallic elements present were in amounts less than 0.01 pct. The NBS Engineering Metallurgy Section measured the tensile strength, elongation, and Knoop hardness of both the Be-Cu Alloy 25 and the Be-Cu Alloy 125. These are given in Table I. The NBS Engineering Metallurgy Section also prepared photomicrographs of the two alloys; these are shown in Figs. 1 and 2.

Jan 1, 1969

By T. W. Watson, D. R. Flynn

,Measurements are reported for the thermal conductivity of four heat-resistant alloys which were measured at the National Bureau of Standards. Data are given for two samples of AISI Type 316 stainless steel covering a combined temperature range from -150° to + 800°C. The thermal conductivities of three samples of AISI Type 347 were measured over the temperature range from -150° to +150C. Thermal conductivity values are given for Carpenter 20 stainless steel from 100" to 800" C. Data are given for Inconel 702, in both the solution-annealed and the age-hardened condition, over the temperature range from -150" to +800C. SINCE 1958 the National Bureau of Standards, at the request of other government agencies or private laboratories, has carried out measurements of the thermal conductivity of a number of metals and alloys. This paper presents available thermal conductivity data obtained in this way on samples of four heat-resistant alloys. The data presented for Carpenter 20* stainless steel are, to the best of our knowledge, the only thermal conductivity values which have been reported for this alloy to date. Although thermal conductivity values for AISI stainless steels 316 and 347 have been reported by previous investigators, the present data are believed to be of particular interest because, for each alloy, the effect on thermal conductivity of small changes in chemical composition can be observed. The data on Inconel 702&apos; are of interest, not only for

Jan 1, 1969

By Y. Kondo, S. Yamazaki, Z. Asaki

Thermal deco7nposition of Pyrite particles in a fluidized bed with inert gas stream was studied. Assuming that heat transfer from the surroundings to the fluidized particles controls the overall decomposition rate, rate equations for the batch process and for the continuous process were derived. In the batch experiment, a linear rate equation satisfies the experimental results and the overall heat transfer coefficient calculated from the rate constant agrees fairly well with that obtained by Leva.l1 For the continuous process, two rate equations were derived, one on the assumption of complete mixing of particles and another on the upward piston flow of particles in a fluidized bed. The former holds for a bed containing a higher fraction of decomposed pyrite realized at lower feeding rates. The latter can be applied for a bed at higher feeding rates. Thus, segregation of particles in the fluidized bed was indicated at higher feeding rates. Bed temperatures also correspond to these conditions. ThERMAL decomposition of pyrite may be represented by Eq. [I]. The pressure of diatomic sulfur gas reaches 1 atm at about 690°C. The thermodynamics,&apos; kinetics,2&apos;3 composition, and properties3-5 of decomposed products of such a reaction have been studied. Pyrite is a very common sul-fide mineral and is often accompanied with other sul-fides. It is of basic interest in nonferrous metallurgy to clarify the behavior of pyrite in the pyrometallur-gical processes of sulfide minerals of metals such as copper, lead, zinc, nickel, and so forth. Interest in this reaction increased recently because of possible elimination of arsenic from pyrite in processing highly purified iron oxide pellets. Producing elemental sulfur from pyrite, instead of sulfuric acid, also aroused interest in this reaction. It is indicated that the thermal decomposition of solid particles, such as calcium carbonate, proceeds through three major sequential steps: heat transfer, interfacial chemical reaction, and mass transfer.637 It is known that the decomposed product of pyrite is very porous2, 3 and the diatomic sulfur gas evolved can easily escape through this layer of decomposed product. It depends upon the circumstances, therefore, whether the heat transfer to the interface within particles or the chemical reaction at the interface determines the overall decomposition rate. The enthalpy change in the decomposition of pyrite is about 33 kcal per mole FeS2 which is comparable to that of calcium carbonate. The decomposition of calcium car- bonate becomes more and more dependent on the rate of transport of heat when reaction temperature increases, such as occurs in a fluidized bed.6&apos;7 It is reasonable to presume, therefore, that the thermal decomposition of pyrite, an endothermic process, carried out in a fluidized bed may be analyzed according to the heat transfer controlling model. This work intends, first, to propose a mathematical model that determines the overall rate in a fluidized bed for the decomposition process and, second, to investigate a few characteristics of the fluidized bed based upon the experimental results obtained. KINETICS OF THERMAL DECOMPOSITION IN A FLUIDIZED BED It is intended in this section to obtain rate equations for thermal decomposition of pyrite in a fluidized bed by assuming that the overall rate is determined by heat transfer from the surroundings to the particles. Both batch and continuous processes are considered. 1) Batch Process. To obtain the rate equation in the batch process, the following two additional assumptions are made. First, the temperature of preheated inert gas, tg, blown into the fluidized bed is assumed to be the same as the temperature of the fluidized bed, tf. Thus, no heat exchange occurs between the gas and particles in the bed and only the heat transfer from the reactor wall kept at tw to the particles is to be considered. Second, the decomposition is assumed to start at the outer surface of the particles and to proceed toward the center. At any given time during decomposition, undecomposed pyrite remains in the tori at a temperature: td. The decomposed shell is composed of FeS1+x whose outer surface is at tp Diatomic sulfur gas evolving at the interface is heated to tf during its escape through the decomposed shell. This is illustrated in Fig. 1. With the above-mentioned assumptions of heat transfer, we have:

Jan 1, 1969