Search Documents

By Joe Zelanko

In order to prevent roof fall accidents and injuries, U.S. underground coal mine operators must develop and implement effective roof control strategies. Various tools are available to assist engineers in developing designs. For example, criteria to address global stability issues (e.g., pillar stability) are well established in the U.S.; effective tools (e.g., empirical and numerical) are available to diagnose potential problems and avoid catastrophic failures. However, most miner injuries occur as a result of local instability (e.g., a roof fall in a single heading or a rib roll from a pillar corner). Hazard recognition and the availability of support plans suitable to those conditions are key to maintaining stability and safety on the working section.

Jan 1, 2011

By Michael Gauna, Christopher Mark

"For decades, pillar recovery accounted for a quarter of all roof fall fatalities in underground coal mines. Studies showed that a miner on a pillar recovery section was at least three times more likely to be killed by a roof fall than other coal miners. Since 2007, however, there has been just one fatal roof fall on a pillar line. This paper describes the process that resulted in this historic achievement. It covers both the key research findings and the ways in which those insights, beginning in the early 2000s, were implemented in mining practice.One key finding was that safe pillar recovery requires both global and local stability. Global stability is addressed primarily through proper pillar design, and became a major focus after the 2007 Crandall Canyon mine disaster. But the most significant improvements resulted from detailed studies that showed that local stability, defined as roof control in the immediate work area, could be achieved with three interventions:• Leaving an engineered final stump, rather than extracting the entire pillar;• Enhancing roof bolt support, particularly in intersections, and• Increasing the use of Mobile Roof Supports (MRS)A final component was an emphasis on better management of pillar recovery operations. This included a focus on worker positioning, as well as on the pillar and lift sequences, MRS operations, and hazard identification. As retreat mines have incorporated these elements into their Roof Control Plans, it has become clear that pillar recovery is not ""inherently unsafe.""The paper concludes with a discussion of the challenges that remain, including the problems of rib falls and coal bursts.INTRODUCTIONPillar recovery has always been an integral part of underground coal mining in the US. When room-and-pillar methods are employed, large blocks of coal in the form of pillars are initially left in place to support the weight of the overburden. Unless these pillars are subsequently recovered, the coal they contain will never be mined."

Jan 1, 2016

By Jorge Cardenas, David Martinez

Blasting-induced vibrations can be predicted with high precision, allowing for the optimization of sequence design, delay timing, and charge configurations to minimize their indirect impact on rock masses. This optimization leads to a reduction in peak particle velocity (PPV) and dominant frequency at monitoring points. However, a crucial aspect of slope safety is estimating the degree to which vibrations influence stability through numerical modeling of the dynamic response. Slope stability is closely linked to rock mass strength, the predominant failure mechanism based on discontinuity orientation relative to the slope face, and the pre-existing stability conditions before dynamic alterations occur. Blocks, wedges, and planar failures tend to slide under lower vibration levels and are more susceptible to resonance, particularly in fractured and low-strength rock masses. To evaluate the interaction between rock mass and vibrations, photogrammetry and artificial intelligence were employed to identify discontinuity families at vibration monitoring sites. This data facilitated the development of artificial discontinuity networks (DFN), which replicated a discontinuous medium within a numerical finite element model. The input signal was recorded at the slope base using triaxial geophones and incorporated into a discontinuous numerical model. The output signal was estimated through finite element analysis and subsequently compared with geophone measurements taken at the same location. Based on real-world output signals, damping parameters and the model’s natural frequency were adjusted to align both frequency spectra. Using the calibrated parameters, vibration records from various blasting projects at different distances were applied as input signals until slope failure was induced, thereby defining maximum allowable vibration limits in terms of PPV and frequency at the monitoring point. This approach provided a framework for optimizing sequence designs, charge configurations, and delay timings to enhance slope safety and prevent failure due to blasting-induced vibrations.

Jan 26, 2026

By C. Hartford, T. Holmes

Bulk-solids handling systems are often the most over-looked component and thereby weakest links in a processing plant’s value chain. Since their performance can dictate that of the entire operation, they actually deserve special attention. When designing a liquid handling plant, density and viscosity are well known and commonly used as design parameters. Bulk solids however, differ. While the design process is similar, the relevant parameters in handling bulk solids are instead friction, cohesive strength, compressibility, and permeability. These then vary depending on the mineralogy, particle size distribution and shape, moisture content, storage time-at-rest, temperature, and consolidation pressure. With so many variables, it becomes important to characterize each individual bulk solid across the full range of representative process conditions within the handling system, plant wide – or if you are not very lucky, suffer the consequences of poor material flow. Measuring flow properties and applying them correctly in bulk solid handling system design reduces project risk, saves significant capital, and drastically increases throughput, especially when done in the early stages of a project. Keywords: Flow Properties, Bulk Solids, Process Conditions, System Design

Jan 1, 2020

By Robert Cook, Valeria Zarate, Jason Hallowell

The long hole open stoping (LHOS) method is widely used in underground mining. While methods to predict stable stope geometries are well established, the ability to maintain a stable back often assumes effective ground support across the full stope span. The efficacy of the support strategy is dependent on rock jointing, quality, density, top cut width and height, and the type, amount, and orientations of bolts installed. However, it is becoming increasingly common for operators to assume narrow top cuts in service of wider stope spans with minimal bolting coverage. Failure to account for the required top cut drift size and support requirements can ultimately lead to raveling type instabilities along stope shoulders that result in back collapse. A new method has been developed to evaluate the minimum top cut dimension necessary to accommodate wider stope spans with various rock bolting configurations. Due to the economic impacts of top cut development and support, this is a critical consideration in the accurate costing and scheduling of a LHOS operation. Tables 1 lists the acronyms are used throughout this paper.

Feb 1, 2025

By Joseph Kennedy

How do terrorists and other criminal bombers acquire explosives to be used in an attack against U.S property and/or citizens? The Bureau of Alcohol, Tobacco, Firearms and Explosives (ATF) with nearly 40 years of investigating bombings and other explosives incidents, has learned that explosive materials intended to be used in criminal acts are obtained primarily by theft, clandestine manufacture or diversion.

Jan 1, 2010

By Gerrit V. R. Goodman, Fred N. Kissell

The Bureau of Mines has evaluated the effectiveness of the safety elements used to prevent tunnel methane explosions. These fa1l under the general categories of better ventilation, better gas monitoring, reducing ignition sources, and improved worker training. For this evaluation, a technique called fault-tree analysis was used to analyze questionnaire responses from 27 tunneling experts. This analysis allowed us to rank the effectiveness of each safety element, and indicates where money is best spent to reduce the chance of a methane explosion. Results indicated that large decreases in the explosion hazard only take place with the simultaneous application of several elements. Most of these involve a human component - the everyday vigilance and awareness of those working underground.

Jan 1, 1991

By A P. Wilkinson

This paper reports on the implementation of the critical control concept to manage material risks in the mining and metals industries. The critical control management (CCM) approach assumes it is better to identify weaknesses in risk controls before an incident happens as opposed to discovering weaknesses from an investigation after an incident occurs. The first is sometimes referred to as active monitoring and the second as reactive monitoring (Health and Safety Executive and Chemical Industries Association, 2006). Both are needed. However, whilst methods for both active and reactive monitoring of risk controls are well established in many high hazard industries, such as oil and gas, petroleum and chemical industries, until the publication in 2015 of the International Council on Mining and Metals (ICMM) guides, (Good Practice Guide and the subsequent Implementation Guide) (ICMM, 2015), there was no specific mining and metals industry guidance on critical control management. This paper reports on progress in implementing the ICMM guidance drawing on two main sources. First, a benchmarking survey of a representative sample of coal and metalliferous mines, both underground and open cut/pit), sponsored jointly by the Queensland Resources Council and the Queensland Commissioner for Resources Safety and Health in the context of a recommendation that the Queensland mining industry adopts high reliability organisation (HRO) principals (Queensland Resources Council and Commissioner for Resources Safety and Health, 2022). Second, it draws on Noetic’s experience of implementing critical control management in mining and other high hazard industries in Australia, Africa, China and North America (Wilkinson, 2018). The paper describes good practices found and where significant improvements can be made, providing specific and actionable examples of both. From this it also identifies how future guidance on this topic could be improved.

Apr 16, 2024

By K Schiefelbein, P OÆGrady, R Balusu, T Ren, T Harvey

"An extensive research program has been undertaken over recent years to reduce the risk of fires and explosions in underground coal mines. The research projects have integrated extensive field studies and computational fluid dynamics (CFD) models of goaf gas flow behaviour to develop optimum proactive strategies to prevent and control spontaneous combustion and fires ingoaf areas. The research has developed a fundamental understanding of the air and gas flowbehaviour in goaf areas and provided a detailed understanding of the eff ects of various geological,ventilation, operational and inertisation design parameters on goaf gas distribution. The researchinvestigations have also provided a better understanding of the flow behaviour of gases from the heating in the goaf areas and the effect of various gas and spontaneous combustion controltechnologies and strategies. Field studies conducted at a number of underground coal mines have shown that the proactive strategies were successful in reducing oxygen ingress into the goaf areas and in reducing the risk of fires and explosions in the underground coal mines. The results of various research investigations and guidelines for reducing the risk of fires and explosions in underground coal mines are presented in this paper."

Jun 1, 2012

By R. N. Chakravorty, R. J. Kolada

Introduction Spontaneous combustion in coal mining is recognized as a major hazard in terms of safety and economics. A survey by Olaf (1979) revealed that 80% of coal mine fires were caused by spontaneous combustion. Modern mining methods demand a high capital investment. Closure of a working face may then result in a huge loss. Even a short production interruption can prove expensive. Spontaneous combustion may also produce lethal amounts of carbon monoxide, thus posing a serious threat to the health and safety of underground miners. The worldwide recession in the early 1980s resulted in a number of mine closures and production cutbacks. So large stockpiles at mine sites were common. Experience has shown that stockpile fires are difficult to extinguish. Critical factors influencing spontaneous combustion There is no simple method of predicting whether a particular mining method applied to a specific coal seam will result in spontaneous combustion. Under favorable conditions of heat accumulation, spontaneous combustion can occur with any type of coal. It is known that subbituminous coals are more susceptible compared to low volatility bituminous coals, and that a high ratio of exinite increases the risk. However, the inherent moisture content of the coal and the exposed surface area may be more significant. Actual mining and ventilation conditions also strongly influence susceptibility. In practice, the experience gained with the mining method applied to a particular type of coal seam must be carefully evaluated with respect to the factors responsible for spontaneous combustion. Feng, Chakravorty, and Cochrane (1973) summarized the critical factors influencing spontaneous combustion in coal mines (Table 1). Prevention methods and strategies Mine layout is the most important factor preventing spontaneous heating. Working districts should be designed so that a particular section can be isolated on short notice without affecting production in others. Sites for preparatory seals should be identified and marked during planning. With coal seams that are highly susceptible to spontaneous combustion, the retreat method of working is preferred. This is because the gob is not subjected to a large difference in ventilation pressure. Coal pillars should be designed to resist excessive crush. The panel system of working is preferred, particularly for mining coals susceptible to spontaneous combustion. The size of each panel is calculated based on the incubation period and the rate of extraction. Controlling air leakage is also important for controlling spontaneous combustion. This is usually achieved by minimizing ventilation pressure difference, proper siting of doors, and avoiding unnecessary stopping and starting of fans. Air leakage is also reduced by sealant coating, injection of cements in cracks and crevices, and by maintaining good gateside packs. Application of inhibitors to control spontaneous combustion met with limited success. Chamberlain and Hall (1973) concluded that borate solution or Montan powder sprayed in the gob area or infused into a low rank coal would reduce the possibility of spontaneous combustion. Early detection of heating Significant research is being conducted worldwide to develop methods for early detection of heating. Monitoring combustion products during the early stage of heating is the most suitable method for detecting spontaneous combustion. The major gaseous products resulting from low temperature oxidation of coal are carbon dioxide, carbon monoxide, and water vapor. In mining operations, carbon dioxide monitoring is considered unsuitable because there are sources other than spontaneous heating from which this gas may originate. Carbon monoxide, however, is a more specific product of combustion during low temperature oxidation of coal. Over the years,

Jan 10, 1988

By J. G. Speight

Laboratory studies indicate that autogenous heating of low-rank coal can be prevented by a prior treatment which involves immersing the coal for short (5-15 min.) periods in an inert liquid at temperatures between ~ 350° and 400°C. Such "carbonization" effectively reduces the accessible pore volume of the coal to levels at which heat generation through subsequent sorption of moisture and oxygen is too slow to cause significant temperature rises in a stockpile. In addition, this treatment also irreversibly removes most of the moisture held in the raw coal and raises its calorific value by as much as 10-12%.

Jan 1, 1973

By John McNeil

Mr. President, and Members of the Rocky Mountain Coal-Mining Institute-Gentlemen : I appreciate the distinction of addressing this representative body of men upon a subject that lies so close to the heart of each one of us, and which is one of the principal objects of our gathering here today, in this beautiful city-so beautiful, with its grand and glorious mountains looking down upon us, that its charm makes us almost forget the men we left toiling "underneath the ground." But that object-the safeguarding of our coal-miners, who spend the greater part of their lives delving in the bowels of the earth-is the cause of our gathering from the "rock-ribbed" States of Utah, Wyoming, New Mexico, and Colorado. And, as I look about me, my eye lights on the face of many an old-time friend- on some with whom I have walked for more than thirty years; so, whatever the merit of this little talk of mine, it cannot be said that it was made by a "tenderfoot." You must not for a moment think that I shall attempt the impossible task of completely covering so comprehensive a subject as '(Accidents in Coal Mines,' and take much more time than has been allotted me, or would be advisable for me to consume. So I shall confine myself, as briefly as possible, to some of the most common causes of accidents, and the possible means by which these disasters may be diminished. For a great many years the cause of mine accidents and their prevention have been the subject of grave thought and investigation by both national and state governments. As early as 1835 Great Britain appointed a royal commission of talented men, possessing special knowledge in the conduct of coal- mining, also eminent authorities in science and its application, to search into these matters. Since 1835 there has been a succession of such commissions of research, at frequent intervals, in all countries wherever coal has

Jan 1, 1913

By Claude Ferquson

MORE men are killed and injured in the metal mines of the United States from falls of rock and ore than from any other cause. Dan Harrington, of the U. S. Bureau of Mines, recently stated that "falls of men and material continue to take about 50 per cent of the lives annually lost in our mines (coal or metal) and this kind of accident is now and has been one of the most difficult to prevent." The fact that comparatively little has recently been written on this important subject for the benefit of the metal miner is the incentive for the present paper. Little will be said that will be new, but I hope to place fresh emphasis on certain well-known' principles' and to reiterate and stress previously stated rules so that the average experienced miner, as well as his buddy who may not be so experienced,' will sit up and take notice. It is not within the scope of this paper to discuss mining methods from the standpoint of safety and the prevention of accidents from falls of rock. It is up to the mine management to select the system of mining best suited to the character of the ore deposit and its wall conditions. This is something that the miner can do little about; although in many mines the management encourages the workmen to make suggestions that will improve existing

Jan 1, 1938

By Harry F. Weaver

WHEN 1 was assigned by the Director of the United States Bureau of Mines to present a paper at this annual meeting of the Mining Society of Nova Scotia, 1 was grateful, honoured, and elated to realize finally a life-long desire to see your beautiful land and visit with you who have the good fortune to live and work here. Naturally, in preparing for this important event, 1 wanted to give you something of special interest within the limits of the subject so I chose an area dose to my heart -the operation of our Federal coal mine inspection service, which has, as its fundamental purpose, the prevention of accidents in and around ?Coal mines. In 1957 the United States had 10,879 active coal mines scattered throughout 28 States and the Territory of Alaska. The production of coal for the year was about 515,472,000 tons, including 2.5,472,000 tons of anthracite and 490,000,000 tons of bituminous coal and Hgnite. Anthracite is mined principally in a comparatively small area of one State. AU the 28 States and the Territory produce bituminons coal and/or lignite. The beds mined range from 18 inches to more than 100 feet in thickness and from the horizontal to the perpendicular.

Jan 1, 1958

By A Campbell

Open pit blasting at Ernest Henry Mining has the potential to cause damage to nearby underground workings. This paper is a case study of the blast vibration management project that was conducted to ensure open pit blasting did not adversely affect the stability of upper production levels or cause damage to the underground primary fan units. The two upper levels of the underground mine surround the lower portion of the open pit mine. The remaining underground mine workings are directly below the open pit mine. This paper details the process developed to prevent open pit blasting causing excess vibration in the underground mine. Measurement of test blasts combined with historic blast monitoring data was used to determine site specific blast vibration parameters. Threshold vibration levels for blast-induced damage to underground drives and the fan chambers were developed from benchmarking and non-linear numerical modelling. A Monte Carlo simulation model was used to predict vibration levels in critical underground areas. Blasts predicted to exceed maximum vibration levels could then be redesigned to avoid damage.A scale distance law for determining peak particle velocity (PPV) from the distance and charge weight of blasts was developed. Underground observations were used to develop a site-specific relationship between PPV and ground support/rock mass damage. A Monte Carlo superposition prediction model was developed and compared to measured data to refine input parameters. Standards for redesigning open pit blasts in order to reduce blast vibrations whilst minimising impacts on productivity are described. Non-linear numerical modelling was used to establish the dynamic capacity of the fan chambers, and set a PPV of 250 mm/s as a threshold for damage. The numerical model captured the full dynamic behaviour of the fan chambers and installed support, including transient stresses, strains and induced damage, when subjected to a simulated open pit blast.This case study also outlines a procedure for monitoring and predicting blast vibrations at other mine sites where open pit blasting has the potential to impact on a nearby underground mine.

Nov 8, 2011

By Xiaojie Yang, Gang Yang, Zhenli Hao, Manchao He, Ruifeng Huang, Zheng Wang, Chaowen Hu

Preventing the spontaneous combustion of remnant coal, which is indicated by carbon monoxide (CO), is a significant issue for coal mining safety. The N00 longwall mining method with Z-type ventilation is advantageous for the prevention and control of CO; however, research regarding this topic is limited. To investigate the distribution of CO in a goaf and working face, a sealing material and technique for blocking the goaf were introduced after proposing a forming method for a Z-type ventilation system; furthermore, a monitoring method was designed and applied in the field. The results demonstrated that the CO concentration during mining in the upper corner and return airway ranged between 4–6 ppm and 3–7 ppm, respectively. More importantly, no CO was generated in the goaf. The results indicate that the advantages and mechanisms regarding the prevention of spontaneous ignition using the N00 longwall mining method with Z-type ventilation are as follows: (1) The adoption of the downward ventilation technique is not only beneficial for reducing the air pressure difference between both ends of the working face, but also prevents CO accumulation in the upper corner. (2) The basis of a spontaneous combustion disaster is eliminated owing to the absence of coal pillars reserved in the goaf. This study proposes a superior method for mitigating spontaneous combustion disasters related to remnant coal in the goaf in a coal mining field and contributes to the better understanding of the N00 longwall mining method for coal mining safety.

Nov 28, 2022

By Mario SINNAEVE, Olivier LEMAIRE, Gisèle WALMAG, Sébastien FLAMENT

Many hot rolling mills worldwide face nowadays bonding zone fatigue problems before reaching scrap diameter of the work rolls. This phenomenon is nowadays known to occur in reversing roughing mills both in stainless steel and in carbon steel rolling. The phenomenon can be explained through longer rolling campaigns, inadequate backup or work roll maintenance, harder steel grades or increased throughput by reduced amount of passes to achieve the same thickness. In order to help users in optimizing the roll use, we developed a numerical tool to evaluate and optimize roll maintenance. This paper will review the influence of roll geometries on stresses generated at the roll surface but also at the bonding zone. We will also show how roll geometries can decrease contact fatigue damages by modifying crowning and chamfering procedures, shell thickness, material design or campaign length

Oct 1, 2019

By L. Salnais

"Aluminum alloy structural components f or aircraft designed prior to the early 1970s, were machined from 2024, 7075 and 7079 plate, bar and forgings in either the T3xxx of the T6xxx tempers. Protective treatments for these parts consisted of chromic acid anodizing and alkyd zinc chromate primer, plus a nitrocellulose lacquer for exterior parts.The major service problem with these parts was the frequent occurrence of exfoliation corrosion and stress corrosion cracking (S. C. C.). Therefore, 2024 and 7079 alloys, with min or exceptions, were not used in aircraft designed after the early 1970s. Replacement materials were 7075 and 7050 alloys in the overaged, exfoliation corrosion and S. C. C. resistant, T73xxx tempers.The use of improved materials together with the upgrading to chromated epoxy primers, polyurethane enamels and the introduction of water displacing corrosion inhibiting compounds have significantly reduced corrosion in aircraft. IntroductionThe prevention of corrosion in aircraft has been a challenge to aircraft designers for many decades. With the design of the first all-metal aircraft, the designer and builder were thrust into the relatively new field of protective treatments as corrosion started to become more prevalent. This resulted from the continually increasing importance and wider utilization of aircraft, and their exposure to a wider variety of ho stile environments such as urban industrial pollution, high humidity tropical areas and salt ladened marine environments.Corrosion advanced another significant step when, after World War II, designs of new and larger aircraft utilized larger and thicker metal sections in the manufacture of structural components. With thicker mill products came higher residual heat treat, fabrication and assembly stresses resulting in an increased number of stress corrosion and exfoliation corrosion problems.Apart from the exterior environment, aircraft interior s can be exposed to a number of fluids which are either directly or indirectly responsible for corrosion. The most common of the fluids is water which is usually introduced as a result of condensation, especially in pressurized fuselages, and spillage from lavatories, galley s and electrolytes from batteries. These fluid s have a degrading effect on protective treatments and are also corrosive to the substrate metal. Fluids such as phosphate ester hydraulic fluids and ester based turbine engine lubricating oil s are not corrosive to the substrate metal, albeit they do contribute to corrosion by the degrading effect on protective treatments."

Jan 1, 1988

By E. Ghali, B. Arsenault

Aluminum alloys play an important role in the manufacturing of air and ground vehicles. However, with such alloys, corrosion damage is often found on structural components subjected to fatigue loading. The alloying provides large benefit in terms of the high specific tensile strength (ultimate strength/density ratio) to the aluminum alloy but causes the aluminum alloy to be more sensitive to localized corrosion due to complex microscopic heterogeneities such as secondary phases. This paper investigates thermal spray coating namely arc spraying to evaluate the protection against environmentally assisted cracking (EAC) and localized corrosion on Aircraft structural 7075 T651 aluminum alloys. In particular, EAC and pitting corrosion at the interface coating-substrate are a challenge for thermal spray protective coatings on aluminum alloys under cyclic load and immersion. To address these issues, different surface preparation techniques prior to arc spraying were considered such as chemical de-oxidation, laser ablation, shot peening and grit blasting. Results indicate that surface preparation and improved coating process parameters play an important role to provide a coating conferring a protection against both localized corrosion and EAC.

Jan 1, 2006

By S. Abe

An extensive study has been carried out to determine the true cause of floating slimes precipitation which sometimes occurs and badly affects the quality of copper cathodes. Soluhilities of floating slime compounds systematically measured for the ternary system As-Sb-Ri added solely or in combination with conventional copper electrolyte (63°C) and bench scale electrorefining experiments done by varying electrolyte composition, have shown conclusively that the level of Sb(V) ions plays a substantial role in the precipitation mechanism. It was, therefore, speculated that controlling the level of the less soluble S b ( V ) ions below a certain critical level should result in a complete elimination of the undesirable precipitation. This can be easily achieved, for instance, by the addition of a reducing agent such as SO2 gas and the simultaneous employment of a certain type of cheating agent that effectively removes excessive Sb and Bi from the contaminated electrolyte. Long-term pilot testing conducted in line with the above speculation has confirmed the SO2/chelating resin scheme to be industrially very attractive and feasible.

Jan 1, 1987