Search Documents

By Brian Raymond

This paper will outline the problems and solutions of the new generation washeries, as well as the recent technological advances which are being considered for future coal preparation plants. The subjects to be covered will include: - reasons for considering coal preparation plants; - raw coal crushing and handling systems; - types of coal cleaning equipment being used versus new equipment being considered; - fine coal circuit sizing; - clean coal centrifuging and dewatering; - thermal dryer problems and changes; - fine refuse dewatering systems; - clean coal storage problems and changes; - materials handling within the plants; and - control systems for preparation plants. The design and integration of the various circuits that form a modern coal preparation plant have led to the creation of an exciting new field of industrial research. As the need for energy sources increases, efficient methods of preparing coals for specific markets will become more important.

Jan 1, 1979

By Zhihe Dou, Yan Li, Qiuyue Zhao, Guozhi Lv, Yan Liu, Hongliang Zhao

"Abstract: How to reduce carbon dioxide emissions has become a vexing problem, meanwhile, there exist high energy consumption and low efficiency problems in the existing CO2 capture and storage technologies. For CO2 comprehensive Utilization, this paper researches a new technology of absorbing the CO2 emission with high alkaline calcium or high alkaline wastewater sludge mineralization of calcium and invent a core device for multi-level jet carbonation. The industrial test has been carried out in China Xinyu slag Engineering Co., Ltd. The wastewater flow is 150m3/h in the pilot scale. The prepared calcium carbonate has a whiteness greater than 90%, particle size less than 150nm. The mineralization of aluminum exhaust with waste carbide indicates that the CO2 absorption rate is greater than 99.0%, CO2 concentration in the exhaust gas is lower than 0.08%, the purity of mineralized calcium carbonate is greater than 99.0% and particle size is less than 100 nm.InstructionAccording to the statistic data from IEA (2009), the carbon dioxide discharge from fossil fuel consumption in China has exceeded it in the US by the year of 2007, China, has become the largest emitter of carbon dioxide all over the world. Meanwhile, the economic scale is still on an increasing trend in the next 50-100 years, leading to a continuous increment in carbon dioxide discharge. According to the international energy agency forecasts, the energy-relative CO2 discharge in China will rise to 11,615 million tons, 91.3% higher than it in 2007. In the year of 2012, the CO2 gross discharge has reached 10,000 million tons, obviously higher than the predicted value. It is a tremendous task to reduce the emission. Non-ferrous metals industry is one of the largest emitters of carbon dioxide among the industrial circle, the whole industry might discharge a huge amount of carbon dioxide (over 600 million tons), in which the electrolytic aluminum industry is the largest energy consuming industry and CO2 emitter. At present, the CO2 discharge has focused by the whole world due to the environmental problems it causes; meanwhile, supplement of new carbon source is needed due to the exhausting oil and coal resources, so that various countries in the world are attaching importance of the recycle and purification of CO2. Many countries are studying on the cyclic utilization of carbon dioxide. Gas CO2 is mainly applied in chemical, pharmaceutical raw materials, beverage filling agent, refrigerant, inert medium, solvents, pressure source, the welding protective gas, antioxidant and fire extinguishing agent, etc. Solid CO2 is mainly applied in penicillin production, fish, cream, ice cream and other food storage and transportation at low temperature, etc. nowadays, such methods as absorption method, membrane separation, adsorption, etc. are widely used to recycle CO2, with such problems as high investment cost and technical constraints etc."

Jan 1, 2014

By W. S. Weldon

The use of spiral separators for the beneficiation of fine coal typically in the size range -2+0.1mm is now well established process technology. Developments during the mid 1980's resulted in the production of cost effective, efficient large diameter coal spiral separators. Recent developments and research have been geared to optimize metallurgical performance, materials handling and equipment geometry of large diameter coal spiral separators.

Jan 1, 1997

By James Paone

Drillability of rocks by mechanical means is closely related to the physical properties of the respective rocks, Various approaches by previous investigators on rock drillability are presented, as well as recent techniques studied by the Bureau of Mines. The studies show drillability concepts based on (1) theoretical drilling equations derived from laboratory drilling experiments extended to field drilling results and on (2) a statistical method where multiple regression analysis is used to develop a prediction equation for drillability.

Jan 1, 1966

By AIME AIME

THE non-ferrous alloys have been placed in the same class with steel by metallurgical research on hardening, and hardenable alloys of all metals except zinc are now manufactured. The hardening of the non-ferrous alloys is accomplished by a process of heating, quenching and ageing. R. S. Dean, head of the research department of the Western Electric Co., told of the results of this research in 'a lecture on "Recent Advances in the Art and Science of Fabricating Metals," given before the Missouri Mining and Metallurgical Association on Jan. 24, 1929.

Jan 1, 1929

By Hans Lundberg

PREFACE THE successful conclusion of all geophysical work depends on the operator's skill and sound judgment, as well as on his knowledge of geology and geophysics. We have been fortunate enough to have as co-workers a number of very good men. Some results of their work are summarized in this paper, and it is a pleasure to acknowledge their cheerful spirit of co-operation and the enthusiasm and loyalty with which they have assisted in the building of a geophysical organization to serve the Canadian mining industry HISTORY Geophysical prospecting is commonly, but quite erroneously, regarded as something new. The name is modern, but the principle of applying physical laws to reveal the presence of hidden ore is several hundred years old. Already, at the beginning of our civilization, the need was strongly felt for methods that could indicate the presence of ore in regions where the ore-bodies were completely masked or hidden from the eye. Particularly in countries where the rocks have been eroded during periods of glaciation and later covered by a thick mantle of glacial debris, all kinds of mysterious schemes were invented to locate the hidden ore. Often magic was resorted to (for example, the divining rod), but methods based on sound principles were also developed. Such features as topography, colour and taste of surface waters, and the growth and occurrence of trees and plants, were used to reveal certain types of ore deposits. For finding bodies of iron ore, the compass was very early in use. The fact that objects of iron attract a compass needle was utilized in prospecting long bef01:e the time of Columbus, and a systematic search for bodies of iron ore by this method was organized as early as the year 1600. There are still in existence documents, dated a little over 300 years ago, which show that the Swedish Chancellor of that day, Axel Oxenstiorna, ordered dozens of sun-dial compasses from instrument makers in Germany. The Swedish Government at that time employed a great number of prospectors to search systematically for iron ore. This Government undertaking must have been quite successful, as a number of iron ore-bodies were found in areas covered by heavy overburden. These prospectors were simply Government 'geo-physicists', although they were not known by this fancy name.

Jan 1, 1937

This paper reviews recent advances in geophysical tools for mineral exploration. It does not restrict comments to methods which are usually applied in the tectonically active belt surrounding the Pacific Ocean, where geophysics has often been secondary to geological prospecting (eg visual recognition of surface alteration) and drainage geochemistry; but considers geophysical tools applied to a broader range of both deposits and terrains. For example, the subdued topography of much of Australia and Canada has lent itself to the development and extensive application of airborne methods. In Australia, deep weathering and transported cover have necessitated the use of geophysical methods to not only detect anomalies but also to map and understand basement geology. This same weathering has caused specific problems, particularly for electrical methods, but recent improvements in instrumentation, processing and visualisation have largely overcome them. A great deal of geophysical data is now being collected by government agencies, often from the air, and made readily available to explorers. In several Australian states it is free, often on line, and in almost all cases it is relatively cheap. These regional data sets are often augmented by more detailed local surveys in areas of interest. Although æanomaliesÆ are still important much more is being done with the high quality data which is now available The results are used for geological mapping, to test geological hypotheses, to construct detailed 3D geological models and, together with fluid flow modeling, to predict optimum locations for mineralisation.

Jan 1, 2004

By O Ishiyama, L Lu

Sintering is the most economic and widely used agglomeration process to prepare iron ore fines for blast furnace use. Due to the depleting reserves of traditional high-grade iron ore, there have been considerable changes in iron ore resources available throughout the world, especially in steel mills in East Asia. Corresponding to the changes in the availability of iron ore resources, the amount of impurities in iron ore has been slowly increasing. Some of these impurities have been found to have deleterious impacts on sinter quality and sintering performance. In the meantime, an increasing number of large blast furnaces with inner volumes of more than 5000 m3 have been built that require more sinter and are often more demanding in terms of the quality requirements of the ferrous materials. Finally, sinter plants are facing increasing pressure due to more stringent regulations regarding their environmental impact. This paper gives an overall review of a variety of technologies developed worldwide to tackle the changing raw material characteristics and mitigate emissions from sintering operations.CITATION:Lu, L and Ishiyama, O, 2015. Recent advances in iron ore sintering, in Proceedings Iron Ore 2015, pp 61–68 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By J. T. Ryan

SAFETY practice or the elimination of accidents in our coal mines is specifically a problem of management. It cannot be delegated to any governmental agency except that the various coal-producing states do and should have some minimum safety standard laws. However, the legislative method of attempting to control mine accidents is ineffective because of the delay between the necessity and the action. It will always be impossible to keep our various state mining laws up to date; and when the law says you must do a certain thin there is a tendency to do this and no more. Unless the scheme for setting up state regulations is so flexible that when a new hazard develops it can be immediately and adequately covered and the whole responsibility for accident elimination placed undivided on the

Jan 1, 1937

By Moto Goto

Today, Pierce-Smith converters, coupled together with various types of smelting units, are used in most of the world's smelters. However, due to the "batch" processing nature, and problems associated with fugitive emissions during the transfer of melt and blowing stages, this arrangement will unlikely be adopted in future smelters. Modern day alternative processes include the Mitsubishi Process, Outokumpu Flash Smelting and Flash Converting Process, the Noranda Process, and the Ausmelt Process, but only the Mitsubishi Process is a "truly continuous" smelting and converting operation, producing a constant flow of blister without tapping, and is economically proven by long term commercial operations. This paper reviews recent advances in modern continuous converting technologies, with a special section devoted to operation of the "first standalone Mitsubishi C-furnace" coupled together with a Noranda Reactor, at Port Kembla Copper Pty. Ltd. in Australia.

Jan 1, 2003

By Moto Goto

Today, Pierce-Smith converters, coupled together with various types of smelting units, are used in most of the world's smelters, However, due to the "batch" processing nature, and problems associated with fugitive emissions during the transfer of melt and blowing stages, this arrangement will unlikely be adopted in future smelters. Modern day alternative processes include the Mitsubishi Process, Outokumpu Flash Smelting and Flash Converting Process, the Noranda Process, and the Ausmelt Process, but only the Mitsubishi Process is a "truly continuous" smelting and converting operation, producing a constant flow of blister without tapping, and is economically proven by long term commercial operations. This paper reviews recent advances in modern continuous converting technologies, with a special section devoted to operation of the "first standalone Mitsubishi C-furnace" coupled together with a Noranda Reactor, at Port Kembla Copper Pty, Ltd. in Australia.

Jan 1, 2003

By R. K. Filip

"Steel bearing piles have long been used to carry high compressive, tensile and lateral loads. Such piles are most commonly tubular or ""H"" profile and are typically installed using percussive techniques. The noise and vibration associated with such installation techniques tends to preclude the use of steel bearing piles in urban and other sensitive areas.This paper describes the design and construction of an innovative new road bridge in Milton Keynes, UK. The steel bearing piles were required to continue out of the ground to form the bridge columns and abutments and then be cast directly into the soffit of the reinforced concrete bridge deck. This project was to be the first time in the UK, that this form of bridge design had been used.The paper shows how new installation techniques allowed the designers to use these high capacity steel elements in a sensitive urban environment without the use of percussive or vibratory installation techniques. Finally the paper shows how these quiet and vibration-less installation techniques can be extended to other applications.A UNIQUE BRIDGE SUPPORTED ON ""BOXED SHEET PILES""CONCEPT HISTORYThere are over 700 bridges in Milton Keynes. Concrete is the dominant construction material, most are single span with massive parallel wing wall retaining abutments. All have a certain uniformity of aesthetic design. Pell Frischmann Consultants Ltd (PFC) proposed to the client, English Partnerships (EP), that an ""integral bridge"" with a slender open appearance would be an appropriate aesthetic form for a new highways bridge, within the district of Westcroft (figure 1). The concept required that the bearing piles be continued up out of the ground to form the bridge columns and abutments. Four rows with four piles in each row were suggested. Each would then be cast directly into the reinforced concrete bridge deck forming a moment connection (figure 2). This concept meant that a single continuous steel structural member would replace traditional reinforced concrete bored piles, pile caps and piers. This member would carry vertical and lateral loads. The conceptual design was intended to meet the following client requirements:"

Jan 1, 2005

By V. G. Papangelakis, G. P. Demopoulos

"Recovery of gold from refractory ores and concentrates presently constitutes one of the most important, challenging, and exciting areas of R&D activity in the gold processing industry. New technologies are being tested for the treatment of refractory gold materials, some of which have been advanced to the level of commercial operation. In this paper, some recent technological developments in the hydrometallurgical processing of pyritic matrix-refractory gold ores are highlighted. Key operational steps of each of the alternate hydrometallurgical technologies are analyzed and potential advantages and drawbacks are identified. The processes which are reviewed are: hydro chemical oxidation, biochemical oxidation and pressure oxidation. INTRODUCTIONOver the years the term ""refractory"" has been applied in gold ore processing to denote situations in which straightforward cyanidation failed to yield high gold recoveries. A number of mineralogical and chemical factors may be responsible for this ""refractoriness"" problem. A systematic classification of the different options for their treatment has been discussed in a recent review paper. In this paper, the pretreatment of the submicroscopic gold encapsulated within the matrix of pyrite and arsenopyrite minerals is considered. This type of gold is the ultimate refractory material because complete breakdown by reaction of the host mineral structure is required.The method which has been traditionally applied for the treatment of pyritic-type refractory gold ores is an oxidation roast (single stage or double stage depending on the As content) of a flotation concentrate to produce a porous calcine, the latter being more amenable to cyanidation. Despite its established practice, oxidation roasting is not considered particularly attractive with today's standards for high product recovery and clean environment. Roasting is known to be very sensitive to heating parameters and feed composition and deviation from optimum conditions can result in reduction in permeability which is translated to incomplete gold liberation."

Jan 1, 1989

By Z. Xu, Z. Li

Colloidal interactions play a critical role in mineral processing, including grinding, physical separation (particularly flotation), dewatering, and tailings management. Despite great energy input in comminution to liberate valuables from gangues, heterocoagulation between valuables and gangues would prevent the separation of valuables from gangues. On the other hand, selective coagulation/flocculation to increase the size of desired fine particles could enhance physical separation and dewatering, while dispersion is needed for fine grinding. To control the state of colloidal dispersions by creating favorable conditions, it is of paramount importance to study colloidal interactions in a relevant system and understand underlying mechanisms. This review summarizes recent advances in developing the-state-of-the-art techniques and novel methods of measuring colloidal forces, including atomic force microscope, surface force apparatus, zeta potential distribution measurement, quartz crystal microbalance with dissipation, and our recently developed integrated dynamic force apparatus. The basic principle of each technique was introduced first, followed by a summary of critical information derived for the relevant mineral processing systems. Finally, the pros and cons of each technique were discussed to emphasize the use of complementary techniques that assist in solving fundamental problems in mineral processing.

By D J. Williams

The majority of surface tailings storage facilities continue to employ sub-aerial tailings slurry deposition. Surface TSFs are typically sized and operated in a way to minimise the initial capital cost of the facility, driven largely by the net present value approach to accounting. This generally leads to too small a storage, too fast a rate of rise of the tailings, and difficulties in managing supernatant water. In turn, this results in wet and soft tailings deposits of high moisture content and low density, and the need for frequent and costly tailings dam raises. Further, such tailings deposits often do not facilitate closure and rehabilitation of the facility. Globally, there are on average over two failures annually of such tailings dams, resulting in loss of life, damage to infrastructure and environmental impact downstream, and the loss of company shareholder value and reputation. Recent high profile tailings dam failures are threatening the mining industry’s financial and social licence to operate.Among the physical processes that tailings undergo on sub-aerial deposition are beaching, hydraulic sorting down the beach according to particle size and specific gravity, settling, consolidation, and desiccation on exposure to the sun and wind. Beaching and hydraulic sorting have proved difficult to test at laboratory scale and difficult to model, and are best assessed in the field. Settling, consolidation and desiccation may be assessed at laboratory scale, but to date there has been an absence of tests to form the basis for the design and management of tailings deposition, and ultimate closure and rehabilitation. The paper describes recent advances in tailings testing methods, including a purpose-built slurry consolidometer that tests the settling and consolidation of tailings from a slurry consistency, simulating increasing tailings depth to about 50 m; and a purpose-built instrumented column that tests the settling, self-weight consolidation and desiccation of a surface layer of tailings, also from a slurry consistency. Selected test results from these two apparatus are presented in the paper, together with brief descriptions of how they may be used to better design tailings slurry deposition. In addition, planned further advances in tailings testing methods are briefly described.CITATION:Williams, D J, 2018. Recent advances in tailings testing methods, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 8–37 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By James L. Whitlock

Biological treatment of mining and industrial effluents reached full scale commercialization around 1980. These proven, low cost, technologies have been limited in application due to a number of factors, including extended periods of time and cost required for pilot testing as compared to chemical treatment technologies, lack of biological expertise in metallurgical personnel, longer treatment periods in some cases, and performance failures based on improper application. Renewed interest in biological treatment technologies is being driven by permits with lower effluent concentration criteria, permits with bioassay evaluation, the need to remove thiocyanate, nitrates, sulfates and? other parameters. Chemical treatment processes, in general, have not been able to meet these present requirements, or require elaborate? combinations of processes, in terms of effluent quality and treatment economics. This paper addresses biologieal treatment of mining and industrial waste waters and selected recent advances in these technologies. The future looks very bright for application of these low capital and operating cost technologies,

Jan 1, 1998

By James S. Falcone

Soluble sodium silicate materials have well known applications in flotation for desliming, selective depression and corrosion control. Recent advances in the understanding of the complex polymeric nature of silicate solutions using NMR spectroscopy, combined with our studies of the effects of polymeric silicate anions on metal ion activities in solution, oxide mineral surface charges and surfactant adsorption on clays are related to beneficiation processes. The results of these studies indicate the sodium silicates can be used to cause a solution chemistry and particle surface charge characteristics favorable to enhanced effectiveness in typical ore beneficiation systems.

Jan 1, 1981

By R. U. Seneviratne, B. K. Ahlgren

In this paper we follow various technological discoveries and developments in the purification of minerals and metals in the mining industry by ion exchange. For approximately 100 years, ion exchange has been a known and variously applied purification and separation technology used by scientists and producers. It would seem obvious that the producer’s objectives have always been to achieve the highest quality products and the lowest operation costs, but also with the least amount of technological complexity. As a strategy to reach these goals, much effort has been expended in the quest to improve continuous ion exchange (CIX) systems by reducing utility needs and resin degradation or loss while at the same time improving productivity and reliability. Recent developments from a number of companies have pushed equipment boundaries, resulting in a variety of unique commercial equipment designs each with a varying degree of success. The challenge set forth for all new designs has been a truly continuous process with no sacrifice in the afore mentioned benefits. One very recent equipment design based on system symmetry appears to meet many of these objectives with greater flexibility and less complexity resulting in better economics for the producer.

Jan 1, 2014

By M. S. Diederichs, J. Oke

Surface limitations and a need for more direct transportation routes require serious consideration be given to the development of underground construction works in geotechnically unfavourable conditions. Due to geographical and logistical limitations, the construction of these underground works is restricted to difficult ground conditions that require temporary pre-support before excavation in order to avoid tunnel collapse or severe surface settlement. One type of pre-support is the umbrella arch system, which has been gaining popularity due to cost and time commitment in comparison with other pre-support systems (e.g., ground freezing). The umbrella arch system has been employed with significant frequency around the world, yet without a complete understanding about the mechanical response of the system. As such, literature has found the temporary support system to be both under and over designed with regard to safety and/or economical impact. The authors of this paper have made three major contributions to increase understanding of the umbrella arch system and to help optimize the design process. Firstly, the authors have developed nomenclature in order to categorize and define umbrella arch elements and systems, which also stimulated the creation of the empirically driven Umbrella Arch Selection Chart. Secondly, the authors have established a design methodology that is primarily based on advanced numerical modelling techniques to aid in the optimized design of the umbrella arch arrangement for site specific conditions. Thirdly, the authors have developed a semi-analytical model for umbrella arch systems employed in squeezing ground conditions by incorporating elastic foundation theory as well as convergence confinement theory. These three major contributions to such a widely employed tunnelling pre-support system will be introduced and explained in detail, and will include discussion of how each is incorporated in the complete tunnel support design process and throughout the construction and monitoring phase of a project.

Jan 1, 2015

By F. G. Smith

Abstract Laboratory methods are now in use whereby the temperature and pressure during the crystallization of hydrothermal minerals can be determined. The techniques include the use of the decrepitation method of studying liquid inclusions, and electrical measurements of pyrite. The determinations are sufficiently accurate that the data can be used in solving a variety of ore deposition problems. Within the last year, several new laboratory techniques have been developed in the Geochemical Laboratory of the Department of Geological Sciences, University of Toronto. The results of several tests of ore by these methods have proved to be useful in treating some problems which previously were considered unsolvable. It is now possible to determine the temperature of deposition of most of the minerals in a hydrothermal ore deposit, also the depth below the surface during deposition. Measurements can also be made of the reopening history of a complex ore. The temperature-pressure determinations depend upon the fact that minerals deposited from a hydrothermal solution always trap a small amount of the solution at the time of crystallization. The solution, being predominantly composed of water, has a density which depends upon the temperature and the pressure prevailing during crystallization. After ore deposition is complete, erosion and isostatic uplift finally exhumes the vein. During this slow fall in temperature and pressure, the solution contracts and a gas bubble appears. If the trapped solution in the mineral is examined, the gas-liquid ratio records the density of the solution at the time the mineral was deposited (except for a slight change in the volume of the mineral). The thermal expansion and compressibility of water and water solutions are known to a sufficient degree that, if the gas /liquid ratio can be determined, the temperature-pressure relations during deposition can be calculated.

Jan 1, 1949