Search Documents

By P N. Duan, Z G. Liu, M S. Chu, X X. Xue, B Liu, G J. Cheng, T Jiang, J X. Liu

High-chromium vanadium-titanium magnetite has not been exploited and made full use of on a large scale so far due to the immature utilisation technology and the reality that the utilisation efficiency of valuable metals still urgently needs to be improved. In the present paper, the isothermal reduction kinetics and mechanism of high-chromium vanadium-titanium pellets were studied at 800–1100°C. The mineral composition transformation of pellets before and after reduction was analysed by means of X-ray diffraction (XRD), and the microstructures were examined by scanning electron microscope (SEM) equipped with energy dispersive X-ray (EDX) to reveal the elemental distributions. The effect of reduction temperature on the volumetric swelling degree and cold crushing strength was also studied. It was found that reduction temperature has a large effect on the reduction rate of pellets, and the increase in reduction rate is more obvious in the range 1000–1100°C than 800–1000°C. The volumetric swelling degree of pellets increased with increasing reduction temperature, while the cold crushing strength decreased. The transformation of mineral species can be expressed as Fe2O3 ? Fe3O4 ? FeO ? Fe, Fe2O3·3TiO2 ? Fe3O4· (2FeO·TiO2 ) ? 2FeO· TiO2 ? FeO·TiO2, (Fe0.6Cr0.4)2O3 ? FeO· Cr2O3 ? Cr2O3 , and Fe2O3· VO/V2O3 ? VO. The apparent activation energy of the reduction reaction was calculated to be 44.3 kJ/mol, and the reduction rate is controlled by the combined effect of interfacial chemical reaction and gas diffusion through the porous product layer. The rate controlling steps were further studied by calculating the resistance percentages. The interfacial chemical reaction was found to be predominant in the initial reduction stage, with the percentage effect of gas diffusion through the porous product layer gradually increasing during reduction.CITATION:Cheng, G J, Xue, X X, Liu, J X, Liu, Z G, Chu, M S, Jiang, T, Liu, B and Duan, P N, 2015. Reduction kinetics and mechanism of pellets prepared from high-chromium vanadium-titanium magnetite concentrate, in Proceedings Iron Ore 2015, pp 349–358 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By E. Asselin, G. K. Yue

"In the present study, electrochemical measurements, especially cathodic potentiodynamic polarization (CPC) and cyclic potentiodynamic polarization (CPP), have been employed to study the kinetics of ferric reduction on chalcopyrite in aqueous Fe(II)Fe( III)H2SO4 solution at 90 °C and 110 °C. Results from the calculation of speciation in the above solution reveal that, at both 90 °C and 110 °C, the real Fe3+/Fe2+ ratio is much lower than the nominal ratio, which leads to smaller VALUES (for the reversible potential of the ferric/ferrous couple. Exchange current densities of the ferric/ferrous couple were obtained and are on the order of 106 10 5 A/cm2 a t 9 0 °C and 1 07 10 6 A/cm2 at 110 °C, respectively. The Tafel slopes from the CPP method are higher than those from the CPC method at both 90 °C and 110 °C. The transfer coefficients were about 0.360.59 at 90 °C and 0.370.65 at 110 °C. Based on the exchange current densities obtained, the rate constant kc was calculated. It was found that kc at 90 °C was slightly larger than at 110 °C, especially for the results obtained by the CPC method. The average rate constants are 862.17 cm/s for CPC and 65.30 cm/s for CPP at 90 °C, and 477.69 cm/s for CPC and 63.53 cm/s for CPP at 110 °C for nominal Fe3+/Fe2+ ratios ranging from 1:1 to 1000:1. INTRODUCTIONChalcopyrite is one of the most abundant copper-bearing minerals, accounting for approximately 70% of the world’s known copper reserves (Wang, 2005). Most of the currently proposed leaching processes are based on sulfuric acid with ferric ions and/or dissolved oxygen as oxidants. Some of these processes have been piloted in attempts to implement these technologies on an industrial scale, such as Activox (U.S. 5,232,491, 1993), Nenatech (U.S. 5,993,635, 1999), Dynatec (U.S. 5,730,776, 1998), AAC/UBC (U.S. 6,503,293, 2003), Total Pressure Oxidation (U.S. 5,698,170, 1997), CESL (U.S. 5,874,055, 1999) and Galvanox (U.S. 7,846,233, 2010).To date, much effort has been devoted to understanding the kinetics and mechanisms of the oxidative processes (Biegler & Horne, 1985; Córdoba, Muñoz, Blázquez, González, & Ballester, 2008, 2009; Ghahremaninezhad, Asselin, & Dixon, 2010; Hirato, Majima, & Awakura, 1987; Hiroyoshi, Kuroiwa, Miki, Tsunekawa, & Hirajima, 2004; Warren, Wadsworth, & El-raghy, 1982) or the cathode reduction reactions of chalcopyrite itself (Arce & González, 2002; Biegler & Swift, 1976; Biegler, 1977; Nava, González, Leinen, & Ramos-Barrado, 2008), by chemical or electrochemical methods. However, as the most important cathodic processes in chalcopyrite leaching systems, the cathodic reductions of ferric ions or dissolved oxygen are worth measuring due to their effects on the overall leaching rate, as predicted by mixed potential theory."

Jan 1, 2012

By M. Wu, G. Plascencia, A. E. M. Warner, A. Vahed, T. A. Utigard

Nickel oxide granules formed by pyrohydrolysis of a chloride solution, were reduced in hydrogen. Below 400 °C, an incubation period was observed, followed by very slow reduction. In the temperature range from 400 to 600 °C, the rate of reduction increased with increasing temperature and increasing hydrogen pressure. Microscopic analysis showed that in this temperature range the reaction followed the shrinking core model. Above 600 °C, the reduction rate decreased noticeably before suddenly becoming very fast at and above 950 °C. Microscopy showed inner bands of metallization inside the outer metallic rim, indicating partial blockage of the interface between the reacted and un-reacted NiO core. At these temperatures, particle agglomeration and sintering were also found to take place. Surface segregation of sulphur may account for the slow down in reduction rate above 600 °C. From an industrial point of view, reduction should be carried out from 550 to 600 °C with as high a concentration of hydrogen as possible. If sintering and agglomeration are not of any concerns, reduction can be carried extremely fast at about 1000 °C.

Jan 1, 2005

By Yuanyuan Zhang, Patrick J. Masset

"The reduction of FexO in slag is one of the fundamental reactions in iron and steelmaking technology, including the blast furnace process (BF). Experiments on the reduction reaction of iron oxide using CaO-SiO2-Al2O3-FexO-C mixtures were carried out using thermogravimetric analysis (TGA) under reducing conditions at temperatures up to 1100°C. The composition of the primary slag was chosen so that the FexO concentration varied between 0 and 75 wt % and the CaO/SiO2 ratio being kept constant to 0.90. From the TGA curves recorded isothermally at different temperatures the kinetic parameters of the iron oxide reduction were determined.IntroductionIn blast furnace the iron ores and coke are charged in layers from the top. The reduction of iron oxide by coke is one of the fundamental reactions in the blast furnace process. Although a great amount of work has been done on the topic of reduction of composites [1, 2, 3], gasification of carbon [4, 5] and reduction of iron oxides by CO [4, 5, 6], the mechanism of reduction in iron oxide - carbon powder mixtures is not fully understood. Fruehan [1] and Rao [2] studied the reaction rate of the reduction of iron oxide by different types of carbon and concluded that the reaction mechanism is controlled by the oxidation of carbon at temperatures up to 1200°C. Rao [2] studied the reaction of hematite with graphite as carbon source up to 1080°C. An activation energy close to 300 kJ/mol was calculated within the temperature range of 950°C to 1087°C. In his study, Fruehan [1] determined the rate of reduction of Fe2O3 and FeO by coal, coke and coconut charcoal as carbon sources within the 900°C to 1200°C temperature range. He found that the reduction of Fe2O3 by carbon occurs in two stages and that the reduction of Fe2O3 to FeO is faster than that of FeO to Fe. This is due to the fact that the CO2/CO equilibrium ratio is higher, and hence, the rate of oxidation of carbon is faster. Fortini and Fruehan [3] have studied the reduction reaction of wustite by graphite and wood charcoal. They found that the wustite reduction can have a significant effect on the overall rate of reduction in composites at high temperatures or in the presence of a large excess of carbon. The calculated activation energy of the reduction reaction by wood charcoal was close to 368 kJ/mol, while the activation energy of the reduction reaction by graphite was 444 kJ/mol."

Jan 1, 2011

By Yongzhong Xiao, Tiejun Chun, Jian Pan, Zhen He, Deqing Zhu

"In this paper, the reduction kinetics of low grade hematite ore was calculated. Mineralogy shows that the ROM (run of mine) ore is of low grade hematite ore type, assaying 27.2 wt% Fetotal and with main valuable minerals of hematite. The reduction kinetics shows that the reduction reaction rates of pellets with additive and without additive are all controlled by diffusion through the product layer. The calculated apparent activation energy of pellets with 12 wt% complex additive is 8.55 KJ/mol, dropping 62.23% compared to that of pellets without additive.IntroductionWith the rapid development of iron and steel industry in China, there has been a soaring demand for iron ores in the past decade. The imports of iron ores have increased from 148 million ton in 2003 to 620 million ton in 2010[1]. Therefore, large quantities of low grade iron resources are necessary to utilize in China at the moment. During the past years, extensive research has been carried out on the low grade hematite ores [2-6], such as reverse floatation, gravity separation, high-gradient magnetic separation and direct reduction-magnetic separation. Direct reduction-magnetic separation is an innovation way to treat the low grade hematite [7]. However, the research of reduction kinetics of low grade hematite is few. Some research about the reduction kinetics of reducing iron oxides by CO was studied [8]. The results indicated that the apparent activation energy is 8.0-28 KJ/mol when the reducing reaction is controlled by internal diffusion. The apparent activation energy is 50-75 KJ/mol when the reducing reaction is controlled by chemical reaction. In this paper, the reduction kinetics of pellets was also been studied."

Jan 1, 2012

By Shengqin Zhang, Jagannath Pal, Yousef Mohassab, Hong Yong Sohn, Mohamed Elzohiery

The kinetics of magnetite reduction with mixtures of hydrogen and CO of various compositions has been investigated as part of the development of a flash ironmaking process at the University of Utah. This new process bypasses the cokemaking and pelletization or sintering steps required for the blast furnace. The particle kinetics were studied using magnetite concentrate particles of different sizes. Reduction degree of 60% was achieved in a few seconds in at 1350 oC using CO reductant alone and over 90% when H2 + CO gas mixture was used. The effects of reductant partial pressures, temperature, and particle size on the reduction kinetics were studied.

Jan 1, 2016

By Shengqin Zhang, Yousef Mohassab, Feng Chen, Hong Yong Sohn, Mohamed Elzohiery, Amr Abdelghany

A novel ironmaking process is under development at the University of Utah aimed at producing iron directly from iron oxide concentrate in a flash reactor. This process will reduce hazardous emissions and save energy. The kinetics of magnetite reduction with hydrogen was previously investigated in our laboratory in the temperature range 1150 to 1400 oC at large temperature increments (~100 oC increments). Due to the significant melting that occurs above 1350 oC, the reduction kinetics was measured and analyzed in two distinct temperature ranges of 1150 to 1350 oC and 1350 to 1600 oC (~50 oC increments). Experiments were performed using magnetite concentrate particles of different sizes under various hydrogen partial pressures and residence times. Reduction degrees of more than 90 % were achieved in a few seconds at temperatures as low as 1250 ºC. Different rate expressions were needed to obtain reliable agreement with experimental data.

Jan 1, 2016

By A. B. Hazar-Yoruç

Ferrochromium produced by smelting chromite ores is an important alloying component in the steel industry. Ore, coke and fluxes are mixed and reacted in an arc furnace for a smelting process of ferrochromium. In ad-dition to this process, pre-reduction of chromite ore with carbon is an important industrial process. In all these processes, the mechanism and kinetics of reduction of chromite with carbon play an important role. In this study, the reduction of Turkish chromite ore with carbon was investigated. Chromite and carbon were ground to three different particle size groups. Chromite was mixed with carbon in stoichiometric and excess ratios. The samples were reduced under argon atmosphere at temperatures between 1,200° and 1,350°C. The formed phases and alloy compositions of reduced chromite samples were analyzed by optical microscopy, scanning electron microscope (SEM) with EDAX and X-ray diffraction analysis (XRD). Experimental results showed that the degree of reduction and the reduction rate increased with increasing temperature and decreasing particle size. The highest degree of reduction, 61.4%, was obtained at 1,350°C. The reduction took place in three stages: Stage 1: transformation of Fe3+ to Fe2+ and formation of metallic nuclei, Stage 2: formation of metallic crust around the particles and Stage 3: growth of the metallic crust and coalescence of the metallic phase.

Jan 1, 2007

By Thomas Brynjulfsen, Merete Tangstad, Eli Ringdalen

Manganese ore fines cannot be added to the submerged arc furnace directly as they will prevent even gas flow through the burden. Low gas permeability in the burden will lower the degree of pre-reduction of ore subsequently increase the carbon and energy consumption of the process. In order to utilize manganese ore fines in the furnace, they are typically agglomerated into sinter. In this work, the melting and reduction properties of Gabonese sinter and Gabonese ore have been investigated in pilot scale experiments. Two experiments were conducted, one with 100% sinter as manganese source and one with 50/50 sinter and ore. Lime was used to achieve a charge basicity of 0.72 in both experiments. The composition of slag samples from the excavation of the furnace was established using EPMA(WDS), and the composition of the tapped slag and metal was found using XRF. It was found that while the coke-bed size would determine the tapped slag composition, the melting behavior of the Mn source would determine the mixing with lime.

Jan 1, 2014

By Margaret E. Harris

The formation of nitrogen oxides, the decay of carbon monoxide, and the concentrations of residual hydrocarbons in the secondary combustion zones of propane-air and methane-air flames were studied in three enclosed burners designed to simulate gas appliances such as space and water heaters. The effect of thermally or chemically perturbing the combustion gases above these flames was determined theoretically and by means of factorial experiments. The concentrations of air pollutants and the flame temperatures were measured, and the effects of ingress of secondary air into the primary and secondary combustion zones, flame stability, burner port surface, and simulated recycling of combustion gases were noted. Based on this study, four principles were derived that, applied to gas appliance design, will insure minimal emissions of these air pollutants: 1. Oxides of nitrogen can best be kept low by depressing peak temperatures to about 3,050° F. 2. If this is not possible, then the secondary combustion zone should be cooled rapidly to this temperature. 3. Carbon monoxide concentrations can be limited by rapid induction of secondary air. 4. Hydrocarbon concentrations can be controlled by designing for well-seated, stable flames. In addition, empirical reaction rates were derived that predict the concentrations of nitrogen oxides and carbon monoxide in the primary and secondary combustion zones.

Jan 1, 1970

By S. D. F. Rocha1, L. Katsarou, G. P. Demopoulos

"Crystalline scorodite (FeAsO4·2H2O) has been pointed out as the most stable compound to immobilize arsenic for disposal due to its good stability performance according to EPA’s TCLP test. However, in anaerobic conditions, arsenic releasing is increased to undesired levels due to scorodite reductive break down, in eh <100 mV at 5.5< pH <7 which causes contamination of groundwater. In this work, the concept of encapsulation by controlled deposition of mineral coatings immune to pH or redox potential variations is presented. Aluminum and calcium phosphates were evaluated as coatings and the release of arsenic from scorodite previously coated with phosphates was substantially decreased when compared to the VALUES (obtained from crude scorodite, both in oxic and anoxic conditions. INTRODUCTIONThe widely acknowledged hazardous properties of arsenic as a soil and natural water contaminant and its adverse health effects when present in drinking water have led to very strict environmental regulations (Mandal & Suzuki, 2002) aiming at the drastic reduction of the presence of arsenic in the effluents of the mining and metallurgical industries.In Canada, the Metal Mining Effluent Regulations (Government of Canada, 2002) dictate that the maximum monthly mean concentration in tailings for arsenic must be lower than 0.5 mg/L. At the same time the new Environmental Protection Agency’s (EPA) standard for drinking water foresees concentrations of arsenic less than 0.01 mg/L, which means that the leachability limit for the industrial waste is set at 1 mg/L arsenic (EPA, 1994; Le Berre et. al, 2007). One of the preoccupations of the mining and metallurgical industries is directed to the elimination of arsenic presence in all its effluents, especially since arsenic is commonly found in many ores mainly in the form of oxides and sulphides. After processing of arsenic-containing ores and concentrates, arsenic can be present either in solid residues and tailings, liquid effluents or in flue dusts. Several of these forms of arsenic waste materials are soluble and therefore may cause the contamination of ground water, if disposed of without further treatment."

Jan 1, 2012

By Guohua Bai, Mingjun Rao, Jianchen Lim, Guanghui Li, Tao Jiang

"By using thermogravimetry, optical microscope and chemical phase analysis, the solid-state reduction of carbon-burdened chromite pellets in the absence and presence of additives were investigated. The effects of reduction temperature, reduction time and additives on the metallization of chromite pellet were studied. The results indicate that the pre-reduction ratio of carbon-burdened chromite pellets is improved with the increase of reduction temperature and the addition of additives. The metallization of chromium is increased from 63.9% to 92.8% at 1300 °C for 4h with the addition of 2 wt.% of sodium borate. Investigation suggests that the reduction of carbon-burdened chromite pellets is diffusion controlled. The apparent activation energy without additive is 192.1 kJ/mol, while it decreases to 170.4 kJ/mol in the present sodium borate.IntroductionFerrochrome is used to produce high strength, corrosion resistant, wear-resisting, high temperature resistant and oxidation resistant special steels, and it is becoming one of the most important alloy materials for the production of stainless and high alloying ferritic steels [1-5]. Demand for ferrochrome is steadily on the rise due to the growth of stainless steel industry. Nowadays, more than 80% of the world's ferrochrome is utilized in the production of stainless steel [6-7].Ferrochrome is mainly produced in submerged-arc furnaces (SAF) with chromite lump ore. However, lump ore merely accounts for 20% of the chromite ore output, while fine ore (< 8 mm) accounts for about 80% [8]. Therefore, agglomeration of chromite fine ore is necessary before charging into SAF."

Jan 1, 2011

By N. Sano

The chromium oxide in stainless steel slags usually exists as Cr2O3. However, there is a possibility that it is oxidized to hazardous CrO3 after disposal or during use. Therefore, some technical developments to reduce chromium oxide by using a smelting reduction technique have been reported recently. This paper describes the fundamentals of the technique which have been applied to ferrochromium production and reviews the recent results in literature.

Jan 1, 2004

By Oscar Jaime Restrepo, Juan Camilo Restrepo, Jorge Ivan Tóbon

Portland cement is obtained by a conventional synthesis process from a mixture of limestone and clay at high temperature (1450 °C). This work reports the possibility to obtain cement silicates via alternative methods like Solution Combustion Synthesis (SCS), which optimize both time and temperature, and the consequences to energy efficiency and mitigation of CO2 emissions. The production of one ton of cement emits between 0.62 and 0.97 tons of CO2 into the atmosphere. In this process the CO2 emissions are between 21 and 59%. The combustion methods are chemical redox processes in which, at high temperature, a self-sustaining and fast wave is generated from using chemical precursors and organic fuels.

Jan 1, 2016

By Jean-Pierre Birat, Ana-Maria Iosif, Denis Ablitzer, Olivier Mirgaux

"Integrating environmental considerations into the product traditional process design is now the major challenge for steel industry. Life Cycle Assessment (LCA) is nowadays considered as an appropriate method for assessing environmental impact and selecting new technologies to reduce CO2 emissions for steel industry.In this paper we propose a new methodological concept which combines LCA thinking with process simulation software in order to carry out the life cycle inventory of classical steelmaking process.Using Aspen PlusTM software, a physicochemical model has been developed for the integrated steelmaking route. This model gives the possibility to carry out life cycle inventories for different operational practices in order to optimise the use of energy, to calculate CO2 and other emissions and to control the mass and the heat balances of processes.It is also shown that such approach can be used to design and assess new technologies for steelmaking without large industrial application.IntroductionDuring recent years, it was recognised that CO2 emissions are the major factor of the global warming effect. In order to meet Kyoto requirements, the steel industry is embracing the challenge of sustainable development by improving its competitiveness and economic success while reducing its environmental impacts. Integrating environmental considerations into the traditional product design process, for powerful eco-efficiency, is now one of the major priorities for steelmakers.The European Steel Industry has measured up to this challenge by creating ULCOS (Ultra Low CO2 Steelmaking) consortium that has taken up the mission to develop breakthrough steelmaking process with the potential to reduce CO2 emissions (Eurofer, 2005). In order to develop technologies to reduce emissions, it is necessary to assess the environmental impact of the classical steelmaking route (coke plant, sinter plant, blast furnace, basic oxygen furnace, continuous casting and hot rolling)."

Jan 1, 2009

By D. A. Milligan

Ammonia leaching of copper sulfide concentrates, matte, scrap or other sources of copper yields copper amnine sulfate solutions which are converted to metal in a two-stage process involving precipitation of inter- mediate sulfites and their thermal decomposition to copper powder of high purity. Processing details and results are given. Considerable simplification in circuitry and cost savings are indicated. Energy requirements are reduced by substitution of copper powder precipitation and ammonium sulfate crystallization for solvent extraction, electrowinning and lime boil.

Jan 1, 1976

By Jörn E. Fischer

Cracks were observed at the top of spray formed billets for some alloys. In this paper the effect of process parameters on crack probability is discussed. After the spray run the thermal conditions at the top of the billet change rapidly. A hot spot with melt residue] can occur inside the billet and shrinkage will be suppressed due to the solidified surface of the billet. In this situation hot cracks can be initialized. The temperature history of the billet during and after the spray run is calculated. The temperature difference between core and outside diameter of the billet is taken as indicator for hot crack probability. The effect of different process parameters on the hot crack probability is discussed. The results lead to a better understanding of the process. The calculations are taken as a tool to find process parameters in order to reduce or avoid hot cracks in spray formed billets.

Jan 1, 1999

By B. Andresen, S. T. Johansen, H. Tveit, S. Grådahl, B. Ravary

The Norwegian ferroalloy industry has high ambitions regarding environmental standards. Basic research work has been performed to improve the fundamental understanding of ferroalloy processes and the environ-mental aspects. This paper will present work dealing with the understanding of formation and control of NOx, PAH and dioxins. During this work various techniques and methods have been applied, such as comprehensive industrial measurements, laboratory experiments, model development and application of Computational Fluid Dynamics (CFD). The main goal has been to reduce the environmental impact of ferroalloy plants, by means of improving the combustion processes done by introducing new charging routines and optimized furnace operations, instead of installing expensive gas treatment systems. The Norwegian obligations in accordance with the Gothenburg protocol are to reduce the NOx emissions by 30%, compared with the 1990 level within 2010. Measures developed in this work have resulted in 40-60%reduction in NOx emission, and major reductions in PAH and dioxins for ferrosilicon and silicon metal plants. This has been achieved by introducing semi continuous charging and improved furnace operations. Semi continuous charging and optimized furnace operations are shown to reduce the blowing activity (i.e. emission of large quantity of SiO over the charge by direct channelling from the crater zone). It also reduces variation in off-gas temperature and dust production. To understand the processes and to achieve our results we have used online equipment, with fast sample rates and response times, to measure the off-gas compositions and temperatures. Most of the measuring techniques used are based upon optical principles making use of the absorption- and emission spectrum of the gases. In addition a new prototype instrument is developed for continuous measurement of off-gas characteristics, total dust amount and off-gas temperature. The presented work is a result of a long term co-operation research and development teamwork, between the industry and the research community, and has improved both the process and reduced the emissions. The work has introduced new process design and operation standards, and has resulted in ferroalloy production with better environmental standards.

Jan 1, 2007

By Binxu Zhaug, Mark Jolly, Xiaojun Dai

"In conventional investment casting process of aluminium alloys for the application of the aerospace industry, to assure the quality of the final casting, usually the foundry uses large runner system which results in low yield, high energy consumption and high GHGs emission. In one case of this investigation, the yield is between 5 ~ 10% which means that the current casting process wastes large amount of energy and generates lots of scraps. By applying a new casting method, the bulky runner system and the melting/holding time are significantly reduced, the quality of the casting is improved, and in the meantime the related energy consumption and GHGs emission are significantly decreased. In the investigation, the energy efficiencies and GHGs emission between the current and traditional processes are calculated and compared.1. IntroductionAs one of the conventional casting process, Investment Casting Process (ICP) and its applications can be traced to thousand years ago [l]. In current casting industry, ICP still plays an important role in the production of small and precious castings with high quality requirements in automobile and aerospace industries. Both casting quality and manufacturing costs which mainly consist of energy costs have crucial effects on the competitiveness of castings in the market. In the production of aluminium alloy castings using ICP, the energy cost and energy efficiency of a casting facility depend mainly on the efficiency of its melting and heat treating performance. In association with the two performances, more than 60 % of the total process energy costs are symbolised in a typical casting facility [2]. Additionally, in conventional ICP of aluminium alloys for the application of the aerospace, to assure the quality of the final casting, typically the foundry uses huge runner system including big risers/feeders which cause low yield, creates lots of scraps and generates high energy consumption. Consequently, there are huge opportunities for casting industry to choose the best practices for potential energy saving. Furthermore, the reasons such as the stringent limitation of environmental legislation in Europe and the pressure of the rising energy price force the casting industry to reduce the energy consumption and greenhouse gases (GHGs) em1ss10n."

Jan 1, 2012

By Yasushi Sawada

An experimental investigation was carried out to study the rates of reduction of iron oxides dissolved in liquid Ca0-SO2-A203 slags by Fe-C droplets at temperatures ranging from 1325 OC to 1550 OC. The %FeO in the slag was varied from 5.5 to 18. Flash X-ray images were employed to observe the behavior of Fe-C droplets in the slags during the reactions and for determining the slag-gas-metal interfacial area. Effect of P205 in the slag and sulfur in the droplet was also investigated. The reduction rates were determined by measuring the volume of CO evolved as a function of time and the estimated slag-gas- metal interfacial area. The reduction rates have increased with increasing %FeO in the slag and the slag temperature. The experimentally established relationship between the reduction rates and FeO (wt%) in slag is given by

Jan 1, 1992