Search Documents

By V. F. Parry, J. B. Goodman, W. S. Landers

"This investigation was conducted: under the direction of A.C. Fieldner, chief, Fuel and Explosives Branch, Bureau of Mines, Washington, D. C. The following members of a Technical .advisory Committee were helpful in advancing the investigation: L. C. Harrington, dean, College of Engineering, University of North Dakota; D. F. Pane, president, Sheridan-Wyoming Coal Co.; Carson W. Smith, president, Consolidated goal & Coke Co.; Durbin van Law, consulting, engineer, Denver & Rio Grande Western Railroad; and C. B. Carpenter, professor of metallurgy, Colorado School of Mines. Coal samples from the Northern Colorado field used in the stoker during 3 years of service were supplied through the cooperation of N. C. Brooks, secretary, Northern Colorado Coals, Inc.This report describes the development and practical tests made on a small stoker-fired system for heating service water automatically. The system was designed to take advantage of the favorable reactivity of low-rank fuels, and the objective was to devise a combination of stoker, heat-receiving, and hot-water storage system Which would be automatic for at least 30 days without attention, while heating service water at minimum cost. The system was developed to a point where coal consumption was less than 10 pounds (or less than 100,000 B.t.u.) per day. The total operating cost of hot water for an average-family-was about $1.00 per month, with coal retailing at $6.00 per ton and electric power at 4 cents a kilowatt-hour. The heating system was designed for the utilization of low-rank fuels, but the general features of the double-tank system can be 'employed fuels, either gas or liquid fuels.The Subbituminous Coal and Lignite Section of the Bureau of Mines began investigations on the utilization of low-rank fuels in domestic appliances during 1939. Tests were made on various devices to find out if they were suitable for the low-rank fuels. Most of the available appliances for burning coal have been designed for the higher-rank fuels, and they are not well-suited for burning the lower-rank coals at maximum efficiency, because subbituminous coals and lignite have high bed moisture ranging between 20 and 40 percent by weight, which lowers heating value to the range of 10,000 to 6,500 B.t.u. per pound. They are noncoking, and the ash content ranges between 4 and 6 percent, with a fusion temperature of about 2,0000 F."

Jun 1, 1946

By Wilbur I. Duvall, S. L. Windes, Leonard Obert

"Previous investigations, too numerous to be listed in entirety, have been performed to determine the physical properties of rock. When considered according to their objectives, most of these investigations can be grouped as follows: First, the geologic group (1,2),4/ in which the purpose was to obtain information on the physical properties of the rocks that make up the earth's crust. Particular emphasis has been placed on the determination of the elastic constants--that is, Young's modulus, the modules of rigidity, and Poisson's ratio – as these quantities determine the propagation characteristics of seismic waves. Second, the structural properties group (3 - 11), in which the physical properties of architectural or monumental stone, concrete and aggregate rock, road blocks (cobblestone), and the like were desired. The tests have been quite general and include, besides the elastic properties; the compressive and tensile strength, and the toughness, hardness, and weathering properties of many types of rocks.To .a lesser degree, investigations have been carried out to determine the physical properties of mine rock. A few reports (12 - 14) present data on the crushability and grindability of mine rock, and a large number of papers discuss grinding and crushing procedures and methods of analyzing the data (for example, see references 15 - 17). Some of the latter group also have given the results of tests on mine rock; however, comparatively few include an adequate petrographic description or information on other physical properties of the rock. A few papers,(18 - 22) have reported studies of the strength of rock specimens in respect to the strength of parts of mine structures, such as pillars, roof, arches, etc. Other papers (23 - 26) have discussed investigations on such subjects as primary and secondary crushing, diamond and pneumatic rock drilling, explosive breaking and shattering of rock, rate of drifting and miring, and other allied problems. The majority of these reports have given no more than a cursory, description of the rocks and have included no statement regarding the physical properties. When statements have been given regarding the physical properties, they have usually referred only to isolated tests, making correlations between variations in the physical properties and variations in the .test under consideration difficult, if not impossible. Some reports have included handbook values on such characteristics as the crushing strength, hardness, and toughness. This practice is not satisfactory, because these values are usually given for col¬lective types of rocks, such as granites, limestones, and marbles, and it is known that the variations of the physical properties within these groups is often larger than the differences between the groups."

Aug 1, 1946

By Andrew Brown

"In recent years operators of brown-ore mines have shown increasing interest in .the reclamation of ore heretofore lost in tailing ponds. In January and February.1945 the author made a preliminary survey of the ponds in the Russellville district, Franklin County, Ala. The Russellville district (fig. 1) was chosen for the preliminary work because it contains many large ponds in a comparatively restricted area. All important properties in the district were visited with Charles R. Wilson of Russellville, who has been familiar with the Franklin County brown-ore industry since 1890; with Edmund Craddock and W. S. Blackburn, managers of the two washers now operated near Russellville by Shook & Fletcher Supply Co., and with S. A. Britton, manager of the Sloss-Sheffield Steel & Iron Co. washer. The larger ponds were measured roughly and tonnages estimated. and samples taken from different areas were analyzed and beneficiated at the Southern Experiment Station of the Bureau of Mines; Tuscaloosa, Ala.The ponds explored were the Sloss No.1 (Ensley); the Sloss No. 8, and the Sloss No. 4-5, which are among the largest in the district and so located, within an area of .three square miles (see fig. 2), that ore from all of them could be-treated,one centrally located washer.Actual work was begun on May 9. Between that date and June 30, when field work was completed, 246 holes in ponds were drilled and sampled, and 15 additional holes were put down primarily to test the drill .in different types of ground with a view to its possible utilization in other types of prospecting. Samples from all holes were analyzed for iron content; samples from 13 holes were sized and analyses made for each size fraction, and six large samples have been composited for beneficiation tests.Brown iron ore has been mined in the Russellville district since 1815, when the first blast furnace in Alabama was built in NW1/4 sec. 10, T. 7 S., R. 12 W., about 3 miles southwest of Russellville (19).-J The furnace was abandoned before the Civil War, and mining continued on a small scale until 1888, when Enoch Ensley began to mine the ridge between Russellville and Pain Creek. His first washer, Ensley No. 1, was about 300 feet south of the junction of the present Tharptown road with the Waco spur of the Southern Railway."

Aug 1, 1946

By E. O. Binyon

"Corundum and andalusite were discovered in August 1944 on what is now known as the Blue Metal group of claims. The property, comprising five unpatented lode claims, is situated 20 Miles northwest of Yerington in the Buckskin Mining District, Douglas County, Nevada, An engineer of the. Bureau of nines examined the property on November 1, 1944, and recommended a small: amount of drifting and crosscutting to determine more definitely the extent and character of the ore deposit. The work that had been done by the owners was for sampling purposes only and was confined to a few small pits on the outcrop, and no effort had been made. to delimit the ore zone. Samples taken from the best surface showings were sent to the experimental station in Salt Lake City for beneficiation tests. The results of the preliminary test work appeared favorable, and upon the strength of them and the recommendations made by the Bureau, 2.5 miles of access road was approved and completed early in 1945. Exploration was started on June 24 and completed September 26, 1945.In its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mines resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision of Dr. R. S. Dean, assistant director.This paper is one of many reporting on various aspects of the Bureau of Mines program initiated in August 1939 by passage of the Strategic Minerals act, the scope of which was. greatly expanded by subsequent legislation.Some of these papers were published as war minerals reports, others as bulletins, technical papers, reports of investigations, and information circulars of the Bureau of Mines or• in, technical journals.The Bureau's program at first included separate investigations by the Mining and metallurgical Divisions, but these were consolidated under Assistant Director R. S. Dean beginning July 1, 1942. Mining and metallurgical investigations carried on in three regional organizations more closely integrated thereafter by a staff of specialists, who reviewed findings made in the field and in Bureau Laboratories, considered proposals for additional work, revised reports for publication, and served as advisors to the assistant director."

Aug 1, 1946

By E. M. Frost

"Helium has great value to the oil and as industry as a tracer gas, according to tests just completed in the Elk Hills Field, Naval Petroleum Reserve No. 1, Kearn County, California. When used as .a tracer gas, small percentages of helium are mixed with natural gas pumped into a reservoir for conservation, repressuring, or cycling purposes. Because minute quantities of helium added to natural gases can be detected by analytical methods and accurately determined, the variations of the helium content of gas withdrawn from various parts of a field when helium has been added to the injected gas give interesting and long-sought data on the movement of injected gas through reservoirs.The Bureau of Mines engineers began their studies of the use of helium as a tracer material in gas-injection operations in the Elk Hills, California, oil field, Naval Petroleum Reserve No. 1, in response to a request by the Navy Department for assistance in connection with an expanded oil-production program instituted in that field. This report discusses the Bureau's work on the problem of determining the direction and extent of migration of injected gas in the Elk Hills reservoir by the use of helium as a tracer gas,The Bureau appreciates the cooperation and assistance of Commodore W. G. Greenman, U.S.N., director, and Commander R. Walling, U.S.N.R., Assistant director, Naval Petroleum .and Oil Shale Reserves, Washington, D. C., Captain H. P. Stolz, U.S.N.R., commanding officer, and Commander F. G. Taves, U.S.N.R.., of the Navy's Elk Hills staff. The Bureau also appreciates the cooperation and assistance given by V. O. Wankowski, F. C. Tratt, Marray Putnam, Dana Champion, and other personnel of the Standard Oil Co., of California, operators of the Elk Hills field.R. A, Cattell, chief, and C. C. Anderson, assistant chief, Petroleum and Natural Gas Division; C. W. Seibel, supervising engineer, Bureau of Mines Helium Plants; and H. H. Hinson, petroleum engineer - all of the Bureau's staff - furnished valuable advice and assistance during the course of the work. H. C. Miller and G. B. Shea of the Bureau's San Francisco Office contributed valuable liaison work. The writer wishes to express appreciation to all these people for their cooperation and assistance."

Jun 1, 1946

By E. M. Frost

"A new apparatus has been devised for quickly and precisely analyzing natural gas for its helium content. The following outstanding advantages make it far superior to any equipment now available for the purpose.3/4/5/6/1. It enables more rapid determinations to be made.2. It has far greater sensitivity than previous apparatus. 3. It is portable.Fifty or more samples may be analyzed in an 8-hour day with the new apparatus and procedure. A maximum of about 10 samples per day could be analyzed with previous apparatus. In the apparatus described, the volume of pure helium obtained from a sample is determined by measuring the pressures created by that pure helium when it is expanded into a constant calibrated volume. In older methods the pure helium separated from a sample is pumped into a burette and measured at atmospheric pressure. The new apparatus and Procedure used with it reduce the average time for an analysis from about 40 minutes to less than 10 minutes,Samples containing a few thousandths of a percent helium may be analyzed as readily as samples containing 1 percent or more, This was not possible with former apparatus. Duplicate samples containing a few thousandths of a percent helium have been analyzed, results checking to one ten-thousandth of a percent. Attempts to measure a corresponding volume of helium in a burette at atmospheric pressure become futile. The ability to determine very small quantities of helium has become of great importance recently in gas- and oil-field engineering studies such Os the utilization of helium as a tracer gas in following the movement of gases through underground structures.A complete apparatus was recently carried more than a thousand miles in a passenger automobile. It arrived without breakage, was .set up and ready to make an analysis in a few hours. .Former apparatus was not portable. The portability of the present apparatus permits taking the apparatus to the field for more efficient prosecution of field engineering problems. The only services required in the field are electricity, tap water, and a source of liquid air or liquid nitrogen.The principle involved is based upon the fact that large volumes of all the constituents usually found in natural gas, except helium, are adsorbed quantitatively on cocoanut charcoal that has been cooled to the temperatures of liquid air. A volume of sample is measured and transferred to a tube of cocoanut charcoal maintained at the temperature of liquid air. After adsorption of all the constituents other than helium, the charcoal tube is connected to a sensitive pressure-measuring device, and the Percentage helium originally in the sample is calculated from two pressure readings and the volume of the original sample."

Jun 1, 1946

By E. C. Yeager, E. O. Wagner, A. W. Koth, V. F. Parry, J. B. Goodman, D. G. Gernes, W. L. Patty

"In July 1943, the Bureau of Nines received an appropriation to investigate the beneficiation of Minnesota iron ores through the use of lignite. The broad objective was to find a way to link the large deposits of lignite in North Dakota with the low-grade iron ores of Minnesota. It was proposed that sponge iron might be made through new methods of processing, and one of the objectives was to determine the possibilities of gaseous reduction of fine ore. The problem of obtaining high-hydrogen reducing gases from lignite was assigned to the Subbituminous Coal and Lignite Section of the Bureau of Mines in August 1943.Through the advice of technical consultants and men familiar with the mineral resources of Minnesota and North Dakota, a tentative program of development was outlined. The first proposal was to study the gasification of lignite briquets in a standard water-gas machine. Previous experience with gasification of lignite indicated that the raw fuel would not be suitable for use in the conventional water-gas process on account of degradation, but gasification of lignite briquets appeared possible. Through the cooperation of the Northern State Power Co„ a series of tests was made at the company's plant in Grand Forks, N. Dak., on lignite-char briquets made by the Lehigh Briquetting Co. at Dickinson, Dak. These briquets are made by the Lurgi process, and they have been used satisfactorily as a domestic fuel. The object of the tests was to compare gasification properties of lignite-char briquets with those of gas. coke made from Kentucky coal, normally used in the Grand Forks plant. The tests revealed that the lignite-char briquets were not suitable for gasification, in the standard water-gas process because of disinte-gration and low efficiency caused by loss of fine carbon.While these investigations were underway, a joint Minnesota-North Dakota Development Commission was formed to aid in planning investigations on development of mineral resources of the two States. Some members of this commission were technical men, who with consulting engineers on the Bureau's staff made up an unofficial technical committee, and assisted in solving certain problems connected with gasification of lignite and beneficiation of iron ores. This committee has been of 'real assistance in guiding the investigation.A technical meeting was held in Minneapolis on November 10 and 11, 1943, for further discussion of objectives and certain technical problems. Results of tests on lignite briquets were presented, and several reports analyzing other methods of gasification were discussed. The Reyerson-Gernes process for the continuous gasification of lignite in an externally heated retort was considered from several angles. This process differs from others in that the natural moisture in the coal is utilized to help gasify the coal, and the volatile matter is largely decomposed. Although this process had been carried out successfully in a small steel retort, no definite design for a commercial-scale retort had .been developed. It was first proposed that the process might be carried out in a Glover-West retort. However, it was brought out that a Glover-West retort would require modification to simulate the process correctly, and that good results might not be obtained even then owing to the leakage of gas through the refractory walls and to an anticipated low rate of heat transfer at the gasification temperature suitable for lignite. Further, the probable leakage of inert furnace gas into the water-gas would be adverse to the Objective to obtain a gas that could be purified to 96 percent hydrogen."

Jun 1, 1946

By H. E. Heide

"Before the war, the United States was the world’s leading consumer of tin, the industrial applications of which had become widespread. Domestic production was negligible, and requirements were met almost entirely by imports, principally from British Malaya, United Kingdom and China. Average annual imports for the years 1925-1929 amounted to 78,009 long tons.With the advent of war in Europe and signing of the Japanese-German pact, it was realized that foreign sources of supplies were threatened, and steps were taken by Congress to forestall critical shortages of tin and other minerals. These steps in regard to tin included stock-piling, improving reclamation and conservation, increasing South American production, constructing a smelter in the United States for treatment of tin, ores, and intensifying the search for domestic tin deposits. Annual imports were raised to 140,873 long tons by 1941. On 1945, annual imports had shrunk to 37,675 long tons and consumption had been reduced to 52,100 tons of primary and secondary tin but not tin content of scrap alloy.The Strategic Minerals Act, passed by the Congress in 1939, authorized the investigation of domestic tin deposits.As Alaska had supplied virtually all of the domestic output of tin, an investigation of Alaska deposits was undertaken in 1940 and 1941 by J. B. Mertie, Jr., and Robert R. Coats of the Geological Survey.The Lost River lode tin mine on the Seward Peninsula was examined by H. E. Heide of the Bureau of Mines in 1942. Possibilities for developing a significant amount of tin appeared favorable, and exploration of the ore bodies was started in August 1942."

Jul 1, 1946

By Staff

"INTRODUCTION Sheet mica is one of the most important minerals in modern industry. It is used in many kinds of electrical devices, and up to the present time no satisfactory substitute for it has been developed. It is necessary for the successful operation of airplanes, ships, motor vehicles radios, and radar equipment. Early in World y r II, the Array and Navy, foreseeing the need for conserving the stock of sheet mica on hand and realizing that imports from India and Brazil were falling off, had strategic mica placed on the critical war-materials list.Examination and exploration by the Bureau of nines indicated that there probably are large undeveloped deposits of mica in Alabama, some of which are near the surface and others at greater depth. The quality of most of this mica is high.During World War I, Alabama mica producers added materially to domestic production, but after 1920 virtually all of the mines closed end miners scattered. During World War II, when imports from India, Madagascar,Brazil,,other foreign sources were reduced, sometime was required for Alabama to act into production. Operators began to produce small quantities in 1942.The Colonial Mica Corporation was created by the Government during 1942 to buy Mica for the Metals Reserve Company, end later Colonial was made sole buying accent for strategic mica. About this time the Bureau of Mines estab¬lished the graphite field laboratory at Ashland, Ala. Samples of mica wore submitted for examination, and advice was requested by property owners and mine operators. This continued during 1943, when as many as 400 visitors a month called at the Bureau's Ashland field laboratory."

Aug 1, 1946

By Peter Grandstone, D. A. Jessup, D. B. Taliaferro

"INTRODUCTION Water flooding of oil sands in Texas as a means of secondary recovery of oil has been practiced mainly in the north-central part of the State, which includes the old shallow fields in eight counties, extending south through Wichita and Clay Counties on the Red River into Brown County.The Texas Railroad Commission, is empowered ""to promote conservation and prevent waste in the drilling, completion, operation, and abandonment of oil wells"" and ""to issue regulations necessary for fulfillment of these ends,"" granted The Texas Co. the first permit to inject water into the oil-bearing sand on December 7, 1935. The permit was granted after the Commission had conducted a number of hearings, which were attended by many operators interested in that method of secondary recovery. Through December 31, 1944, the Commission had granted 50 permits for water flooding. Of that number, 45 permits were issued for projects in north Texas, the remaining 14 being distributed throughout west and south Texas. By the end of 1944, there were 33 active and 5 abandoned water-flooding projects in the North Texas area, as is in figure I.Oil production in the North Texas area started in 1904 from the shallow sands (ranging from 100 feet to 800 feet in depth) of the Petrolia (or Henrietta) field in northern Clay County. Development was rapid and unrestricted during the boom period from about 1911 to 1918, and considerable waste of both produced oil and reservoir energy resulted."

Jul 1, 1946

By William Seymour

"INTRODUCTION Byproduct-coke manufacture is one of our country's most essential in¬dustries; its importance was strikingly accentuated by the demands of World War II. This paper reviews recent progress in various phases of byproduct-coke operations for the production of metallurgical coke particularly that used as blast-furnace fuel.In the early days of the by-product-coke industry in the United States high-grade bituminous coking coals, both high-volatile or gas coal and low-volatile Pocahontas coal, were plentiful, and the selection and mixing of coals for coke-oven use were minor problems.The demands of World War I for the production of iron, steel, and coke aroused and stimulated new interest in the investigation of the reserves, characteristics, and properties of our coking coals. During that war the increased demand for coke reached a critical stage, and the shortage of high-grade coking coals necessitated the use of cols of inferior quality and of different coking characteristics than those previously used.The period of prosperity following World War I brought much progress and development in the by-product-coke industry. Methods of testing coal and coke were improved. The search for satisfactory coking coals was continued, and construction and design of byproduct ovens were improved."

Jun 1, 1946

By S. M. Runke

"During the past three years the Bureau of Mines has carried on an extensive research program at the Rolla Laboratory for the beneficiation of low-grade Arkansas baixites by ore dressing methods. As a result of this study a 50-ton pilot mill was designed and constructed at Bauxite, Arkansas, by the Bureau to continue the investigation on a semi-commercial scale. The built both to reduce the experimental work to practice and to obtain operating data that cannot be determined by laboratory or small scaleTen samples of bauxitic material were mined and stockpiled at the plant site to ensure an ample supply of material for milling in the pilot plant. These samples were obtained from various bauxite deposits in Saline and Pulaski Counties, Arkansas. The deposits were selected as typical of a wide range of bauxitic material which would necessitate treatment under different conditions and by various concentration methods. All of the samples contained a higher silica content than permissible in Bayer-grade bauxite and several contained so much iron oxide that the available alumina content of the ore was mate¬rially lowered. From data obtained by milling operations on these ten samples, milling characterietics of most of the ores in the district should be predictable. This paper summarizes the results obtained in the laboratory testing of representative samples of each stock pile, and the results of small scale continuous testing of the composite sample of the ten stock piles in the gravity-flotation pilot plant at the Rolla Laboratory."

Aug 1, 1946

By J. E. Tiffany, Z. C. Gaugler

An active list of permissible explosives was published in December 1943 as part of the Bureau of Mines Report of Investigations 3736 under the title "Active List of Permissible Explosives and Blasting Devices Approved Previous to June 30, 1943." This list included 180 brand names. Changes in the list that have been authorized to December 31, 1945, placed 10 additional brands of permissible explosives on the active permis- sible list as a result of tests and changes in brand names.. Twelve permis- sible explosives were transferred from the active. to the inactive list. The present list contains 178 brand names. The brand names of the permissible explosives placed on the active list are as follows: American 3-A By test. Apcol No. 1-B Do. Black Diamond No. 11-B DO. Black Diamond No. 55 DO. Coalite G-1 DO. Coelite K-1 Do. Do. Coalite L-1 Coalite IS-1 Columbia B-2 DO. By change in name. By test. Monobel AA The permissible explosives transferred from the active to the inactive list are as follows: Anthracite B, L. F. Big Red No. 8 Independent No. 1, L. F. Independent No. 2, L. F. Independent No. 3, L. F. Independent No. 4, L. F. Independent No. 5, L. F. Independent No. 9, L. F. Independent No. 9-C, L. F. Independent No. 10, L. F. Independent No. 11, L. F. King No. 9

Jul 1, 1946

By F. Sillers, R. T. C. Rasmussen

"INTRODUCTION This is the third report of investigations by the Bureau of Mines in cooperation with industry to establish the value of electrolytic manganese in the manufacture of ferrous and nonferrous alloys. The manganese was produced by the Bureau at its Boulder City pilot plant from domestic ores and by the process developed by it. 4/ The work was done under the direction of R.S. Dean, assistant director, Bureau of Mines, and R. G. Knickerbocker, chief, metallurgical branch. The first report dealt with the use of electrolytic manganese in the manufacture of stainless steels 5/ and the second with its use in acid electric or open-hearth low- and medium-carbon steel castings. 6/The present report treats of the use of electrolytic manganese in the manufacture of low—carbon rimmed and killed steels. A résumé of these three investigations and two others appeared in the magazine STEEL. 7/ Further reports will be published as tests are completed at some 70 industrial plants. All tests were made on full—scale heats or melts, and the resultant product was processed and used commercially."

Jul 1, 1945

By V. F. Parry, W. S. Landers, John B. Goodman

"INTRODUCTION The object of this investigation was to demonstrate a satisfactory method of storing slack subbituminous coal in open pits in a manner,that would minimize the cause of the physical deterioration and would have a practical application.The storage of coal by industrial plants is to their advantage, since an adequate operating supplying of fuel is available at all times as insurance against transportation delays, shortages, and strikes. Furthermore, it is possible to participate in low seasonal freight rates and mine costs by permitting the railroads to utilize idle equipment and by taking advantage of the off-peak production at the mines. For a number of years, one of the larger beet-sugar companies operating in the Rocky Mountain region has taken advantage of the lower prices and seasonal production of subbituminous slack coal during the summer months and purchased a large proportion of its requirements for the annual winter campaign. This company, operating sugar-refining plants in the 1943 campaign, used 256,613 tons of subbituminous coal. Of this quantity, 166,636 tons was purchased during the off-peak season and stored for use during the winter. It is the practice of this concern to place coal purchased through the months of January to October in underwater storage for use in the beet-sugar campaign, which lasts from October to as late as, January. The beet-sugar refining ""campaign"" period starts immediately after the beginning of the beet harvest and lasts 60 to 70 days."

Aug 1, 1946

By L. R. Burdick, R. Wiggers, J. F. Berkley

"INTRODUCTION On February 23, 1944, Solid Fuels Administrator Harold L. Ickes stated that the existing fuel shortage made it necessary to utilize a great surplus of freshly mined anthracite ranging in size from Barley (No. 3 Buckwheat) downward through the smaller sizes. As a part of the program to increase the use of such coal, field trials of mixtures of bituminous slack coal and anthracite Barley were made on industrial-size stokers at many fuel-burning plants. The following covers the test information it was possible to accu-mulate during the work of initiating the use of these mixtures at the plants.SUMMARY AND CONCLUSIONSField tests of various mixtures of bituminous slack coal and anthracite Barley on industrial-type stokers show that the use of such mixtures is very practicable and that it is possible to change and usually to adjust to an improved condition the characteristics of a fuel bed of eastern bituminous slack coal by the addition of proper amounts of anthracite. The improved uniformity of the fuel bed of single-retort stokers makes possible less manual attention to the bed. Air flow through the fuel bed is affected.Smoke is decreased. In general, the fly ash and also the unburned combustible in the fly ash and refuse are increased. Clinkering in the fuel bed is generally lessened. The peak-load carrying capacity of the stoker is definitely affected, usually adversely for the higher percentages of anthracite."

May 1, 1946

By R. G. Knickerbocker, T. E. Evans, J. L. Morning, D. R. Torgeson, F. W. Wessel

"INTRODUCTION Pilot-plant studies on processes for converting low-grade domestic manganese ore to high-grade oxide or sulfide products by pyrometailurgical process was initiated at the Boulder City, Nev., Experiment Station in 1942. These investigations were given impetus by the possibility of a national shortage of ferro-grade manganese oxide for war needs.The manganese ore employed-in most of the pilot-plant smelting tests was from the manganosiderite-nodule deposits at Chamberlain, S. Dak. This deposit although low-grade, is extensive and represents, the largest reserve of manganese in continental United States. 6/ The Bureau of Mines has recently developed a Carryall mining-conical rolls treatment method that shows promise of making possible economic removal and subsequent beneficiation of the nodule-bearing shales. 7/ Smelting tests were made also on Artillery Peak, Ariz., mill concentrates in the productions of unrefined manganese matte for the steel The pilot-plant smelting program was based upon the fundamental fact that manganese, like copper, will sulfidize and become miscible with FeS. The matte this formed represents the initial smelting step in the pyrometallurgical treatment of the beneficiated ore. The concentrated nodules containing about. 18 percent manganese were smelted with varying amounts of pyrites and appropriate fluxes to produce Mns-FeS mattes containing 16 to 50 percent manganese. When the manganese and iron was completely sulfidized, the mattes contained 16 to 23 percent manganese. Reducing the pyrite resulted, of course, in the selective sulfidization of manganese and the production of a matte containing a correspondingly higher ratio of MnS to FeS. Complete sulfidization smelting produced slags of lower manganese content and hence resulted in higher manganese recoveries in the matte."

Sep 1, 1946

By R. S. Dean

"INTRODUCTION The metallurgical research program of the Bureau of Mines has been somewhat disorganized, but generally advanced by the increased activities of the war period. The present report is for the purpose of summarizing the work of the Bureau in this field for the past 15 years and indicating its future plan.Fifteen years ago the Bureau turned from its pioneer work on the physical chemistry of steelmaking to an emphasis on raking a pure steel synthetically, rather than by refining, that is, :producing each of the steel 'constituents in the pure state and combining them by simple melting. Such a procedure permits the use of less high-grade ores, not only of iron, but of the ferroalloy metals, such as manganese and chromium,This program has led to extensive work on iron-ore concentration, agglomeration, reducibility of ores and agglomerates, direct reduction of iron ores and concentrates by a wide variety of processes; special refining processes for iron, the production of pure mangenese, chromium, and cobalt from low-grade ores by electrolytic processes, the production of ferrochromium, ferronickel, and ferronickel-cobalt from low-grade domestic ores, and the development of many special alloys to effectively use the new products.The status of the work in each of these fields and the future program of work, together with a bibliography of papers and patents by the Bureau staff on each of these subjects, are given."

Jul 1, 1946

By Guy Ervin, Delwin D. Blue, John E. Conley

"INTRODUCTION Extraction of alumina from various materials, such as low-grade bauxite and clay, by means of a lime-soda sinter has been the subject of a number ofinvestigations (1, 2, 3, 4, 5, 7, 9, 10, 11, 12, 13, 16, 17). 5/ in recent years, Although many of the details of these investigations are lacking, it is believed that there is one difficultly that frequently develops under certain conditions, namely, that of thickening or gelation of the slurry formed during extraction of the sinter. If gelation occurs even to a slight extent* Serious mechanical difficulties result, very low liquor recoveries are obtained, and the extraction step becomes virlually inoperable. Under 'favorable conditions, a solid gel is formed which can only be removed from the equipment with great difficulty. At the Eastern Experiment. Station of the Bureau of Mines in College Park, Md., a study of lime-soda processes was begun in November 1941. This work has included studies on low-grade bauxites, kaolin clay, and nodular diasporic clay. Gelation was most serous with kaolin clay and least with diasporic clay. As a part of the Bureau's investigation, a study was made of the effect of the pertinent variables on gelation. The results permit the selection of various sets of conditions at which gelation will not occur. These data are essential to the final selection of optimum conditions for the over-all process."

Aug 1, 1946

By Whitman E. Brown

"As part of a Nation-wide program of the United States Government to develop natural resources, funds were made available to the Bureau of Mines for the investigation of the ""Reduction of Iron Ores by Solid and Gaseous Fuels."" These investigations are concerned with the direct production of iron from its ores without the use of a blast furnace. Many processes have been proposed for the low-temperature reduction of iron oxides, but few have been developed to commercial use. High-quality sponge iron is produced com-mercially only in Sweden.The cost of iron production depends in part on the grade of the ore and increases with decrease in grade. The substitution of cheap natural gas in a sponge-iron process for expensive coke in smelting in the blast fry pace would partly compensate for the use of low-grade ores. If a process can be developed in which inexpensive natural gas can be used as fuel and reducing agent, the large deposits of low-grade iron ore and the natural-gas resources of east Texas may be utilized in the commercial production of sponge iron.Sponge iron may possibly be used to supplement scrap iron, pig iron, or, in special instances, wrought iron. Sponge iron will vary but slightly in composition and will contain little or no nickel, cobalt, manganese, copper, and other allowying metals. It is becoming increasingly difficult to obtain choice scrap iron of nonalloy composition. Pig iron contains 1.5 to 3.0 percent silicon and 3.0 to 4.5 percent carbon. Sponge iron generally contains less carbon than pig iron.The Madaras Steel Corp. in Longview, Tex., built a set commercial-scale sponge-iron plant which was intended to be operated in connection with a steel foundry. The process is based upon the reduction of preheated iron ore, with hot reducing gases under pulsating pressure. Although the Madaras Corp. had previously experimented with the production of sponge iron by reducing the ore with pure hydrogen, several attempts to use a re-formed natural gas as the reducing agent in this pilot plant were unsuccessful. The Bureau of Mines leased this plant and conducted an extensive investigation of the Madaras process on a semicommercial scale.The experiments were not entirely satisfactory, partly because of mechanical difficulties and partly because the reducing gas was not of the best quality. However, much information on the production of reducing gas by re-forming natural gas and on the reduction of iron ore with re-formed natural gas was obtained.The sponge iron produced contained approximately 0.1 percent phosphorus; and, after melting in an electric furnace, the iron contained approximately 0.15 percent phosphorus. The results of attempts to improve the ore by ore-dressing methods were not encouraging."

Aug 1, 1946