Search Documents

By G. L. Humphrey

Although silicon carbide has been an important manufacture refractory for many years, knowledge of its thermodynamic values has been seriously lacking. In fact, some of the very properties that make it a useful substance, particularly chemical inertness, obstruct determination of its heats of formation and reaction. This paper reports the results of new measurements of the heats of combustion and formation, low-temperature heat capacity, entropy at 298.16°K., and heat-content and entropy increments between 298° and l,800°K. Two varieties of silicon carbide were studied -the common, hexagonal (type II) and cubic. The data are combined to obtain heat and free-energy-of-formation functions, which are given in tabular form. It is shown that the cubic variety is the more stable at temperatures to at least 1,800°K but, because of the inherent difficulties and errors in the heat-of-formation determinations at 298°K, it was not found possible to specify the free-energy difference accurately. The mechanism of silicon carbide formation from silica and carbon is not known and is not ascertainable from thermodynamic data. It appears improbable, however, that it can be a single-step reaction. Some reactions involving silicon monoxide gas and metallic Silicon, as possible intermediates in silicon carbide formation, are considered and shown to be thermodynamically feasible.

Jan 1, 1952

By O. C. Blade

A comparison of certain properties of the commercial aviation gasolines produced in the United States during October 1949, 1950, and 1951 is presented in table 1, the 1951 data being average values from tables 3 through 6 of the present report. Trends in the average values of certain characteristics of these fuels may be seen in figures 1 through 4 which also indicate the minimum and maximum values. As may be observed, with the exception of changes in kinematic viscosities, the properties of commercial aviation gasolines have not varied greatly during recent years. A list of aviation-gasoline survey reports published by the Bureau of Mines is given on page 6. A summary of the average values of the properties on jet fuels is shown in table 2.

Jan 1, 1952

By H. W. Wainwright

.1. The purification pilot plant and the equipment, solution, and gas cycle used for removing hydrogen sulfide and carbon dioxide are described. 2. As sulfur recovery is necessary in any large Fischer-Tropsch plant, pilot-plant runs were made at 300 p.s.i.g. to study the efficiency of tri-ethanolamine solutions in removing selectively hydrogen sulfide from gases containing varying amounts of carbon dioxide. 3. Aqueous solutions of TEA of 20, 30; 35, and 50 percent were investi¬gated. Data indicate that 30 to 35 percent is the optimum concentration if both selectivity and economy are considered. Slightly better selectivity is obtained with the.20 percent solution, but steam consumption is greater owing to the higher solution rates. Results from our pilot plant runs indicate that a 50 percent solution not only produces an acid gas of lower hydrogen sulfide content but also requires high solution rates to effect hydrogen sulfide purification. 4. Data from 37 runs using TEA are presented in tabular form. In addition, the data are correlated and presented in three sets of curves. By using these curves, it is possible to calculate the compositions of the purified and acid gases for various raw gas mixtures. 5. In cooperation with the Southern Natural Gas Co., investigations were carried out at 300 p.s.i.g. on the simultaneous removal of hydrogen sulfide and carbon dioxide, from gases using various concentrations of diethanolamine. 6. Data from 17 runs employing 20, 30, and 40 percent DEA are reported in both tabular and graphic form. 7. A comparison of the data from one DEA run made at 200 p.s.i.g. with those from the runs operating at 30O p.s.i.g. shows float the absorption capacity of the solution, and, hence, the steam requirements per gallon are about the sage for both pressures. .The only real advantage of the higher pressure is the additional volume of gas that can be treated. 8. The quantity of steam needed to reactivate fouled TEA and DEA solutions increased as the reactivator pressure was increased about 1,0 to 1.1 pounds of steam was required for each gallon of circulating solution when the reactivator was operated at 5 p.s.i.g. 9. A curve is included that shows the effect of the hydrogen sulfide con-centration in a lean 35 percent TEA solution on the hydrogen sulfide content of the purified gas and on steam consumption for reactivation. 10. Both TEA and DEA reduced the organic sulfur content of the raw synthesis gas considerably. Analyses of the lean amine solutions showed a gradual build up of sulfur compounds, indicating that the compounds formed by the amines and organic sulfur do not break down under the ordinary operating conditions of the reactivator. 11. Considerable operating difficulty was encountered in the pilot plant owing to foaming of the amine solutions. Laboratory experiments in which the effectiveness of certain antifoam agents was studied showed Alkaterge C to be most promising for the particular conditions studied.

Jan 1, 1952

"SUMMARYThe K.M.A. reservoir was discovered to be oil bearing at a depth of 3,719 feet on March 11, 1931. Extensive development, however, was not begun immediately, because the discovery well had a low initial daily oil production, and market conditions for oil were unfavorable. Development of the field progressed slowly for the next 6 1/2 years. In the latter part of 1937, a wildcat well approximately 2 miles southwest of the discovery well was drilled on a magnetometer high and completed with an initial flowing production of 2,016 barrels of 43° A.P.I.-gravity oil in 12 hours. Rapid development of the southwestern part of the K.M.A. field was begun immediately and continued until over 700 wells were drilled and approximately 12,500 acres proved oil productive.Because of the large size of the entire K.M.A. field, this report is limited in scope to the southwestern part only, and the discussion that follows pertains to this area only. The closing date for production statistics is August 1, 1949.The K.M.A. structure is a complex anticline having a maximum closure of 250 feet, and the K.M.A. formation is composed of sediments that grade from limestone through sandy lime and limy sand to sandstone with thin streaks of shale. Two distinct members of the K.M.A. formation, zone I and zone II, are oil productive. Core analyses indicate the average porosity to be 16.5 percent for zone I and 16.1 percent for zone II. A relationship was established from core data, which showed the correlative permeabilities to be 42.1 millidarcys for zone I and 39.5 millidarcys for zone II, whereas the arithmetical averages of the permeabilities were 84 millidarcys for zone I and 216 millidarcys for zone II. Connate water saturations were 17.5 percent for zone I and 20.0 percent for zone II. The porosity-saturation method, using a thickness-correction factor, was employed to calculate the volume c 168.1 million barrels of stock-tank oil initially in place in the reservoir. Analyses of the reservoir oilIn that, although the initial reservoir pressure was 1,750 p.s.i., the original reservoir oil was saturated to only 1,300 at which pressure 1 barrel of stock,tank oil contained 525 cubic feet of gas in solution.A serious decline in reservoir pressure during the 2 years of rapid development alarmed the operators and caused them to consider a cooperative pressure-maintenance program. In the latter part of 1939, the K.M.A. Pressure Maintenance Association was organized, and the gasoline plants in the field agreed to process the wet gas and return the dry gas to leases having gas-injection wells. Approximately 27 percent of the cumulative volume of produced gas had been returned to the reservoir by August 1, 1949."

Jun 1, 1952

By Rollie P. Dobyns

The K.M.A. reservoir was discovered to be oil bearing at a depth of 3,719 feet on March 11, 1931. Extensive development, however, was not begun immediately, because the discovery well had a low initial daily oil production, and market conditions for oil were unfavorable. Development of the field progressed slowly for the next 6.5 years. In the latter part of 1937, a wildcat well approximately 2 miles southwest of the discovery well was drilled on a magnetometer high and completed with an initial flowing production of 2,018 barrels of 430 A.P.I.-gravity oil in 12 hours. Rapid development of the southwestern part of the K.M.A. field was begun immediately and continued until over 700 wells were drilled and approximately 12,500 acres proved oil productive. Because of the large size of the entire K.M.A. field, this report is limited in scope to the southwestern part only, and the discussion that follows pertains to this area only. The closing date for production statistics is August 1, 1949. The K.M.A.? structure is a complex anticline having a maximum closure of 250 feet, and the K.M.A. formation is composed of sediments that grade from limestone through sandy lime and limy sand to sandstone with thin streaks of shale. Two "distinct members of the K.M.A. formation, zone I and zone II, are oil productive. Core analyses indicate the average porosity to be 16.5 percent for zone I and 16.1 percent for zone II. A relationship was established from core data, which showed the correlative permeabilities to be 42.1 millidarcys for zone I and 39.5 millidarcys for zone II, whereas the arithmetical averages of the permeabilities were 84 millidarcys for zone I and 216 millidarcys for zone II. Connate-water saturations were 17.5 percent for zone I and 20.0 percent for zone II. The porosity-saturation method, using a thickness-correction factor, was employed to calculate the volume of 168.1 million barrels of stock-tank oil initially in place in the reservoir. Analyses of the reservoir oil indicate that, although the initial reservoir pressure was 1,750 p.s.i., the original reservoir oil was saturated to only 1,300 p.s.i., at which pressure 1 barrel of stock-tank oil contained 525 cubic feet of ea~ in solution.

Jan 1, 1952

By James J. Dawd

The investigation to evaluate the reserves of coking coal is being made by the Bureau of Mines in three parts: (1) To estimate known measured and indicated recoverable reserves of all coking coal; (2) to upgrade marginal coals through effective preparation; and (3) to study carbonizing properties of coals and coal blends not now widely used for metallurgical coke making. This is the ninth of a series of reports giving results of studies by counties under part (1) of the investigation. (See Appendix.) This report covers Raleigh County, W. Va., which comprises parts of Bald Knob, Eccles, Beckley, Meadow Creek, Mullens, Flattop, and Big Bend quadrangles. (See fig. 1.) A base map for each bed in each quadrangle was made to the scale 1 inch equals 1,200 feet. Maps of mines, location of drill holes, bed and total coal thickness, and outcrop of the bed were plotted on the maps. With all available data plotted, isopach lines were drawn to limit areas of known unmined reserves in beds 0 to 14 inches thick, 14 to 28 inches thick, 28 to 42 inches thick, and over 42 inches thick. These areas of coal reserves also were divided into measured" and "indicated" categories. All areas in each thickness range and in each category, mined-out areas. areas excluded from the estimate but which may contain reserves based only on geologic inference, and areas outside of the outcrop were measured by planimeter on the base maps, Estimates of total reserves 14 inches and more thick and maps for individual beds were prepared from these data.

Jan 1, 1952

By William L. Crentz

Early in the nineteenth century, coal from Clearfield County entered the eastern commercial market. Ashley reports that coal was moved down the Susquehanna River by ark from Clearfield to Columbia, a distance of 260 miles, as early as 18o4. Around 1850, the famous Moshannon or Lower Freeport bed was discovered. Several years later the Moshannon Basin was developed extensively, and the coal from this area soon acquired an enviable reputation as a high-quality industrial fuel. Today much of the original Moshannon Basin coal is worked out, and the Lower Kittanning bed has replaced the Lower Freeport bed as the principal source of production in southeast Clearfield County. With depletion of the thick underground deposits, the importance 'of Clearfield County as a coal Producer would have diminished rapidly, if it had not been for strip mining the thinner beds. About 60 percent of the coal produced in the county is strip-mined, and the trend toward this mining method is expected to continue as the older underground operations are exhausted. Many strip mines are working in beds that are too thin to be recovered economically by any other method.

Jan 1, 1952

By James J. Dowd

The investigation to evaluate the reserves of coking coal is being made by the Bureau of Mines in three parts: (1) To estimate known measured and indicated recoverable reserves of all coking coal; (2) to upgrade marginal coals through effective preparation; and (3) to study the carbonizing properties of coal and coal blends not now widely used for metallurgical coke making. This is the tenth of a series of reports giving the results of studies by counties under part (1) of the investigation. (See appendix.) This report covers Knott County, Ky., which comprises parts of the Salyersville, Prestonsburg, Troublesome, Hindman, Pikeville, Cornettsville, and Whitesburg quadrangles. (See fig. 1.) A base map for each bed in each quadrangle was made to the scale 1 inch equals 1,200 feet. Maps of mines, locations of drill holes, bed and total coal thicknesses, and the outcrop of the bed were plotted on the maps. With all available data plotted, isopach lines were drawn to limit areas of known unmined reserves in beds up to 14 inches thick, 14 to 28 inches thick, 28 to 42 inches thick, and over 42 inches thick. These areas of coal reserves also were divided into "measured" and "indicated" categories. All areas in each thickness range and category, mined-out areas, areas excluded from the estimate but which may contain reserves based only on geologic inference, and areas outside of the outcrop were measured by planimeter on the base maps. Estimates of total reserves 14 inches and more thick and maps for individual beds were prepared from these data.

Jan 1, 1952

By R. F. Stevens

A laboratory method for examining crude shale oil is described. The method uses only about 500 ml. of sample and a limited number of analytical determinations. Results provide information on the general characteristics and composition of an oil and serve as a basis for comparing different oils. However, the method does not provide for direct estimates of yields of commercial products. Analyses of 10 oils produced in the United States by different methods of retorting and of 10 shale oils from commercial-scale operations in 6 foreign countries are given. The shale-oil-analysis method presented in this paper is based on and employs the same equipment as the Bureau of Mines routine method for analyzing crude petroleum. As shale oil contains groups of compounds not generally found in petroleum, several modifications of the petroleum method that might increase its suitability for application to shale oil were investigated. The modifications included in the present method take into account the apparent poor heat stability of shale oil and the presence of large quantities of olefins and nitrogen compounds.

Jan 1, 1952

By John D. Prater

Thallium is one of the rarer metals that has come into commercial importance in recent years. Although the element was first reported by Crookes in seleniferous deposits in lead chambers of a sulfuric acid plant in the Harz Mountains of Germany, it had no commercial significance until about 190O because of the high cost of extraction. Thallium occurs widely in the earth's crust but is found in such low concentrations that it is recovered only as a byproduct from processing other elements. There are no domestic ores of thallium; the entire output in this country is supplied by the American Smelting & Refining Co. as a byproduct of its cadmium operations at Globe, Colo. Thallium also is recovered from the flue dusts of sulfuric acid works in which thallium-bearing materials are used and as a byproduct of the lithopone industry. This paper describes methods for recovery of thallium from 'white arsenic" and lead Cottrell-precipitator dust of the American Smelting & Refining Co., lead smelter, Murray, Utah. Owing to an enlarged market for thallium because of increased military requirements and expanded peacetime uses, the Salt Lake Station of the Bureau of Mines surveyed the occurrence of thallium in ores, concentrates, and smelter products from all parts of the nation and found the most promising source was certain smelter products of the American Smelting & Refining Co. plant, Murray, Utah. Much of the thallium was being lost in marketed arsenic products; therefore, this investigation was undertaken to develop methods for recovering the thallium.

Jan 1, 1952

By O. C. Blade

A summary of the characteristics of motor gasoline for the winter 1951-52 is presented in table I, and for comparison, a similar summary for the winter 1950-51 is shown in table 2. Trends of some of the more important characteristics over a period of years are shown in figures 1 and 2. The results of this survey show that octane numbers have risen slightly since the summer of 1951 but are below the record levels of the winter of 1950-51. The fractions of a unit change since the summer preceding have resulted in the research and motor-method octane values being virtually the same as the figures for the survey of summer 1950. In volatility characteristics the winter gasolines have changed very little. Average Reid vapor pressures are 10.5 pounds for both grades of fuel compared to 10.4 and 10.5 pounds for premium and regular-price gasolines, respectively, of the winter of 1950-51.

Jan 1, 1952

By A. E. Back

A method has been developed in the laboratory for successfully treating titaniferous magnetite ore from the deposit at Iron Mountain, Wyo. The ore is roasted with 15 percent sodium carbonate to convert the vanadium to a water-soluble form and fix the soda for the subsequent electric-smelting step. Approximately 90 percent of the vanadium is recoverable in a product assaying 80 percent V2O5. The leached calcine is briquetted and smelted in a graphite-lined electric-arc furnace. Substantially all of the titanium is recovered in a soda slag, assaying 60 percent TiO2 and 2 percent Fe, which can be upgraded to 75 to 80 percent TiO2 by leaching with dilute sulfuric acid. The upgraded slag could be utilized for the production of titanium dioxide pigments or titanium tetrachloride. About 90 percent of the iron is recovered as pig iron, containing only minor amounts of vanadium, titanium, and sulfur. The high TiO2 slag compares favorably with slag containing about 70 percent TiO2 being produced by the Quebec Iron & Titanium Corp. at Sorel, Quebec. The data obtained from this investigation indicate that a feasible process has been developed for treating Iron Mountain ore, and larger-scale testing is warranted to develop engineering data for the ultimate utilization of this deposit as a source of titanium, iron, and vanadium. There are adequate supplies of basic raw materials, electric power, water, sodium carbonate, coal, and petroleum products within fairly short distances of Cheyenne and Laramie, Wyo., the nearest cities and probable plant- and labor-supply points.

Jan 1, 1952

By M. C. McCall

When electric current of any appreciable magnitude flows from a power line into the earth, a change sometimes takes place in the conditions of resistivity immediately surrounding the electrode or medium of contact. If the conducting medium is composed of moist earth or clay the effect is to increase rapidly the resistance. If the conducting medium is coal or a coal bed, the effect is one of slowly decreasing resistance as the coal is carbonized, If, however, the flow of current is not enough to carbonize the coal, it will dry slowly, with a resultant increase in resistance. Measuring ground resistance, or impedance, with conventional commercial ground testers does not always indicate the current that will flow in the earth circuit from a direct-current or an alternating-current power circuit. The exact reason for this has not been determined however, it is thought to be due to the comparatively minute currents used for such testing. A typical ground, tester used by the authors for this work indicated a maximum current of 25 milli-amperes. The frequency of this testing current also has an effect on the readings in all probability. While the possibilities of the effects of varying frequencies has by no means been fully explored in this investigation, there are very definite indications that the impedance of a circuit through a section of earth will vary in some inverse relationship to the frequency of the applied voltages. This is evident at ordinary power-line frequencies ns well as at higher frequencies up to 200 kilocycles, which was the highest frequency available for tests in this investigation. This report is written in the hope that it will stimulate further investigation of the possibilities suggested for communication and the development of safety devices for increased electrical safety in coal mining.

Jan 1, 1952

By H. L. Gilbert

Improvements in production of high-purity chromium metal by magnesium reduction of anhydrous chlorides and by hydrogen treatment of electrolytic chromium are reported. Hydrogen-treated chromium has been arc-melted, and the arc-melted material has been successfully forged, rolled, and swaged. The material also has been forged at liquid-air temperatures. X-ray and metallographic studies indicate the recrystallization temperature of rolled chromium sheet to be about 750° C. Preliminary investigation of hot-bending characteristics of rolled chromium sheet shows the minimum bending temperature to be about 325° C. The heat resistance of chromium has been investigated.

Jan 1, 1952

By William L. Crentz

Pike County in the easternmost portion of Kentucky is one of the major coal-producing areas in the eastern Kentucky coal field. The county contains numerous coal beds, many of which are too thin to support mining. The commercially important beds are usually 4 feet or more thick, but selective mining at some places calls for removal of a much thinner section of the bed. The variation in quality of the beds from place to place and the large number of coal beds make correlation uncertain. Samples were collected from 14 different coal beds, of which the Elkhorn group is by far the most important. In addition to the Upper Elkhorn No. 3, Upper Elkhorn No. 2, Upper Elkhorn No. 1, and Lower Elkhorn beds that comprise the Elkhorn group, the Winifrede, Williamson, and Bingham beds constitute the principal coal deposits in Pike County.

Jan 1, 1952

By Robert T. MacMillan

A process has been developed in the laboratory and expanded to semi-pilot-plant scale for recovering titania, iron, and byproducts from two types of titaniferous iron ores. A reducing roast with coke and soda ash followed by grinding and magnetic separation produced powdered iron and slag from which titania and byproducts were recovered by H2SO4 decomposition. Based on the steps tested on a. semi-pilot-plant scale supplemented by the results of the laboratory investigations, enough data are available to make a balanced flow sheet. Combined data from the laboratory and semi-pilot plant indicated that 85 to 9O percent of the titania content of the ore was recoverable and that approximately 90 percent of the iron could be recovered as a metallic-iron powder. Tahawus magnetite from the Maclntyre mine at Tahawus, N. Y., was successfully treated as follows: (1) The ore was roasted at 1,050° to 1,080° C. with carbon and soda ash, thereby reducing the iron to metal sponge and retaining the titania in the slag. (2) The metallic iron was separated, after wet grinding, by magnetic or gravity means. (3) The slag fraction was air-roasted at 850° C. and leached with NaOH to recover Na3VO4. (4) The leached solids received a dilute-H2SO4 leach to remove interfering impurities, chiefly Na2O and SiO2. (5) Titania was dissolved from the leached solids of step (4) by a H2SO4-bake followed by a water leach. (6) Titania was precipitated by seeding and boiling the resulting solution. The spent liquor was used for the dilute-H2SO4 leach in step (4). The following scheme was found to be technically feasible for recovering other byproducts of the process. (1) The gelled filtrate from the dilute-acid leach step was washed and dehydrated to produce a commercially acceptable silica gel. (2) The wash liquor containing sulfates of Na2O, Al2O3, Fe2O3, and TiO2 was combined with the highly alkaline filtrate from the wet-grind and metallic iron-separation steps, precipitating iron and titanium hydroxides, which were separated for special treatment. (3) Anhydrous Na2SO4 and Al2O3?3H2O were recoverable from the alkaline filtrate from step (2) by evaporation and carbonation, respectively, and the barren liquor was recycled to the magnetic-separation step.

Jan 1, 1952

By James A. West

The Quapaw pool is one of the smaller pools in an extensive area of Bartlesville-sand production in the eastern part of Osage County, Okla. (fig. 1). Most of the fields in this area were discovered from 1906 to 1916 and were developed and operated similarly. The Quapaw pool is representative of the area, and much of the developed in studying this pool is applicable to the other reservoirs. This petroleum-engineering study of the Quapaw pool was conducted to provide reservoir data that may aid in more widespread application of the intensive secondary-recovery production methods that have been employed with excellent results in the Bartlesville-sand fields of nearby Washington, Nowata, and Rogers Counties. This study is particularly appropriate because of the intense interest in Osage County fields as areas suitable for water flooding. Water flooding was introduced first into Oklahoma during 1931 in Rogers County, and activity was concentrated in the shallow Bartlesville-sand fields of and Nowata Counties for many years. Although water-flooding projects are now operating throughout the State, the intense activity of the Nowata-Rogers Counties area spread to adjoining counties only during the past few years. Since 1948 the rate of oil production in Washington County (between Nowata and Osage Counties) has increased by 260 percent as a result of water flooding. Currently, leases in eastern Osage County are sought eagerly by water-flood operators, and during the past 2 years the Osage Indian Agency has issued nine permits for water-flooding projects in eastern Osage County. Water-flooding operations are in progress on several projects. Although large oil reserves in eastern Osage County should, be recoverable by water flooding, development and operation of projects will be more expensive than projects in the shallower producing areas to the east. In addition, the Osage County reservoirs appear to be more complex and somewhat more difficult to water-flood successfully. It is hoped that this study will contribute to better understanding of the Quapaw reservoir and, in a general way, to the many similar reservoirs in eastern Osage County.

Jan 1, 1952

By W. J. Kroll

This report is concerned with the many sidelines that were investigated incidental to developing a process to produce ductile Zirconium by members of the staff of the Bureau of Mines laboratory, Albany, Oreg. The results of the main investigation, concerning the production of malleable zirconium by reduction of chloride with fused magnesium under helium, have been described in previous publications. These should be taken as a background to facilitate understanding of this work. Literature on the metallurgy of zirconium has been summarized in a separate publication (2), and references are given in this report only when new publications have to be considered or old ones stressed. Most of the observations described in this report can be applied to the problems involved in making titanium with virtually no change. In general, titanium is easier to reduce than zirconium, since its affinities are lower. Also, its chloride is easier to handle and keep clean because it is a liquid at room temperature.

Jan 1, 1952

By C. H. Riggs

This petroleum-engineering study of the Healdton oil field in Carter County, Okla., describes the geology and production history of that field and estimates the oil reserves that could be produced by efficient secondary-recovery methods. The Healdton field, in western Carter County approximately 20 miles west of Ardmore, Okla., was discovered in 1913 and was one of the early important oil-producing areas in the State. Although the volume of oil recovered from the Healdton sands has been comparatively high, studies show that a large reserve remains in the pressure-depleted sand, which can be recovered by efficient water-flood operations. In making this study of the Healdton-sand reservoir, the writers utilized many data already available in company and Government offices. Most of the fluid samples were collected by Bureau of Mines personnel and analyzed in the Bureau's laboratories at Bartlesville, Okla.; but other data, including logs, core analyses, and production records, were obtained from outside sources. These data were examined critically but were not verified, and possible errors in the original data may be reflected in the conclusions. In this study, attempts were made to consider only those aspects of the available information that would contribute to a clear and concise engineering report on the Healdton-sand reservoir. Other phases of the data, as well as those concerning associated reservoirs, were eliminated from consideration as being irrelevant to the particular problem. Cores and drill cuttings of the Healdton sands were analyzed and studied to determine the nature of the reservoir rocks. Analyses of samples of produced oil, water, and gas were studied to fix the different types, the limits of their occurrence, and the suitability of different waters for injection into the Healdton sands. Records of oil, gas, and water produced and of gas and water injected were studied to interpret the production behavior of the field and of certain individual leases. Theoretical calculations were made to predict the probable water-flood behavior and oil recovery, at constant water-injection rates, for individual sands on two leases.

Jan 1, 1953

By Vernon C. Davis

In initial attempts to mine taconite by conventional open-pit methods, the material tended to break into tabular blocks that were too large to be handled by conventional shovel dippers and were unsatisfactory in an ordinary crusher feed. A great amount of secondary blasting was necessary, which added considerably to the cost of mining. The Bureau of Mines and others are engaged in studies designed to contribute to the solution of taconite-mining problems. These studies concern problems related to drilling techniques and patterns, types and methods of use of explosives, and other factors relative to effecting maximum fragmentation at minimum cost. This report, is concerned with study of the application of shaped charges in drill holes, the effectiveness of shaped charges as compared to capped charges in secondary blasting, and the merits of different drilling patterns and methods of detonation of conventional-explosive charges. Fragmentation of taconite at or near the surface is controlled or strongly influenced by joint and bedding planes. Since all tests in this study were made in a jointed and bedded area, a definite conclusion as to the relative effect of a shaped charge in a drill hole, as compared to a conventional charge at greater depths and tighter ground, is precluded. However, application of shaped charges in primary blasting of taconite appears to be of no advantage. In secondary blasting of taconite, conventional, capped charges produced better breakage than shaped charges of the designs tested. Based on the results of conventional blasting practice in horizontal-, inclined-, and vertical-hole tests, no better fragmentation is obtained from blasting either horizontal or inclined holes, compared to vertical holes. Holes drilled in staggered parallel rows that intersect both series of joint planes at the greatest possible angle, give maximum breakage compared to rows paral-lel to one of the series of joint planes. Methods of detonation made little difference in breakage; but the milli-delay caps produced the best conditions for moving the broken rocks.

Jan 1, 1953