Search Documents

By H. M. Thorne

The Union of South Africa has been interested in oil shale for a long time, and deposits of oil shales, torbanites, and similar rocks have been found in many parts of the country. (Fig. 1.) Samples differ markedly in oil yield and in the characteristics of the oil. The strata vary in thickness, and most of the deposits that have been found are in unfavorable locations because of remoteness from markets or absence of transportation facilities. This report deals mainly with the torbanite deposit near Ermelo, Transvaal, in the Union of South Africa, and the operations of the South African Torbanite Mining and Refining Co., Ltd. (hereafter referred to as Satmar), in mining the torbanite, retorting it, and refining the crude oil.

Jan 1, 1954

By H. N. Dunning

A comprehensive research program designed to aid development of new and improved methods for more complete production of petroleum from partly depleted reservoirs is being conducted at the Bureau of Mines Petroleum Experiment Station, Bartlesville, Okla. Water flooding has accounted for much of the petroleum produced by secondary-recovery methods; however, a considerable portion of the crude oil commonly remains in place after water flooding has been terminated. In recent years the possibility of increasing the efficiency of water flooding by using surface-active additives has received wide attention. In general, the results of laboratory research have shown that use of detergents as water-flooding additives will reduce the residual petroleum in porous media (1).3/ Some less extensive field tests have supported this conclusion but have not been entirely conclusive (2). Later studies (3, 4) have given conflicting evidence as to the relative worth of detergent additives for water floods in water-wet (hydrophilic) or oil-wet (hydrophobic or lipophilic) reservoir materials. The results of these studies emphasize the need for a more complete understanding of the fundamental principles involved in displacing petroleum from reservoir surfaces by injected fluids. Accordingly, a comprehensive research program was initiated to investigate the practical and fundamental aspects of detergency in petroleum production.

Jan 1, 1953

By Herbert Cremer

The United States,-the largest nickel consumer in the world, produces virtually no nickel from domestic ores. Dependence upon outside nickel - sources and increasing strategic, importance of nickel focused the attention of the United States on deposits within its boundries. The most likely domestic sources of nickel are low-grade oxide and silicate deposits, such as the Cle Clum deposit, Kittitas County, Wash., and the Riddle deposit, Douglas County, Oreg. The Federal Bureau of Mines, Northwest Electrodevelopment Laboratory, Albany, Oreg. has been investigating electric smelting of low-grade oxide and silicate nickel ores. These smelting studies have been on selective reduction to produce low-carbon ferronickel. Selective reduction is based upon the relative reducibility of: nickel, iron, and chromium, in the order named, when the charge contains insufficient carbon or other reductants to reduce the entire quantity of these metals present in the ore.

Jan 1, 1954

By H. G. Iverson

As a part of the program of investigation of domestic sources of manganese ore, mining engineers of the Bureau of Mines examined and sampled three properties in the vicinity of Winnemucca, Nev. As the ores were too low grade for direct production of ferromanganese, they were tested for their amenability to concentration by ore-dressing methods. Two samples of ore were procured by examining engineers of the Bureau of Mines from several outcrops in the Pollard Canyon area, Pershing County, about 30 miles southeast of Winnemucca. The manganese occurs in relatively small lenticular bodies as secondary replacement deposits in chert and quartzite. The first sample represented average run -of -mine ore as exposed in the Pollard Canyon deposits. Sample 2 was composed of hand-sorted, high-grade ore.

Jan 1, 1954

By G. M. Potter

During investigation of the occurrence of manganese deposits in the western United States, the Bureau of Mines collected 2-ton samples of 4 ores from 3 properties in northeastern Nevada. Laboratory tests were made to determine the amenability of these ores to ore-dressing methods of concentration. The Caviglia-Vietti property is situated 11 miles southeast of Ely, White Pine County, Nev. The ore deposits are lenticular veins and irregular masses found in limestone fracture zones and along the contact of limestone and underlying shale. Two samples, of the ore were tested: Lot A, from the Vietti shaft, and lot B, from the. Caviglia shaft.

Jan 1, 1954

By R. Havens

During investigations of the occurrence of manganese in the western United States in the early 1940?s, examining engineers of the Bureau of Mines collected samples from seven claims and mines in southern Arizona. For convenience in reporting the results, the work on the properties is grouped in three districts. As the ores were too low grade to be acceptable to producers of ferromanganese, beneficiation studies were made to determine the amenability of the ores to concentration. The San Fernando group is about 10.5 miles south of Patagonia in the Harshaw mining district. G. T. Humphries and D. Alonso held an option on the property, which was owned by H. Bender. Two samples were taken; 1 was a picked sample and the other a representative sample of ore as exposed in the mine.

Jan 1, 1954

By Cleo G. Rall

The method for determining the effective porosity of oil- and gas-bearing sands described in this report is a development of earlier methods (28)3/ devised by the Bureau of Mines. The apparatus bas been improved and made more convenient to use, but the procedure is essentially the same as that which has been in use for maw years. A tabulation at the end of the report gives the results of more than 4,800 porosity determinations for oil sands4/ in the fields of 13 States, A selected bibliography of references to articles containing descriptions and evaluations of various methods of' determining porosity is included in this report. The method was devised and developed at the Petroleum Experiment Station at Bartlesville, Okla., as part of the Bureau's research on fluid-energy relationships and on methods of improving the recovery of crude oil from underground reservoirs.

Jan 1, 1954

By John B. Gayle

The coking time has considerable influence on the throughput of a coke oven, and for this reason a large number of papers dealing with the relationship between coking time and the different operating variables have been published. Although all factors known to influence the coking time have been studied, agreement has not been reached on several questions.2/3 Therefore, it appears worthwhile to evaluate any data that become available during investigations of the carbonizing properties of various coals and coal blends. Because it is expected that reports covering several different phases of this problem will be forthcoming as additional data-become available, the following study of the relationship between coking time and bulk density represents a report of progress on the overall investigation of factors influencing the coking time in slot-type ovens. The practice of including coarse coal in the blend going to the ovens to obtain increased bulk densities is well known. Similar increases have been realized by adding small quantities of oil to the coal mix. Although it would appear that such procedures provide inexpensive methods for increasing the capacity of existing coke-oven installations, Ramsburg and McGurl4/ point out that this increase is possible only if the additional coal can be carbonized in the same coking time as regularly employed without using abnormally high flue temperatures. This statement is in substantial-agreement with the position of Auvil and others5/ and implies that any change in bulk density may be accompanied by a corresponding change in coking time. On the other hand, a recent review of proposed methods for calculating the time required for carbonization6/ includes a number of equations that completely ignore the effects of variations in bulk density.

Jan 1, 1954

By A. J. Barry

Recent developments in mechanizing longwall it mining in Europe have aroused considerable interest among American coal-mine operators because this method provides an opportunity to improve safety, production, efficiency, and recovery. The success of longwall mining in Europe has depended to a large degree on development of effective roof-control systems. One of the major contributing factors in designing these systems is development off improved supports, which combine high load-bearing capacities with controlled yield characteristics, to use in the face areas. Other factors that relate to successful longwall mining involve knowledge of the structural properties of the strata above end below the coal bed being mined, movements of these strata induced by mining, and effects of the strata movements on the strata itself, as well as on the support system used. Extensive studies of the above factors relating to long-wall mining have been made in coal-mining countries abroad, and corresponding studies (1, 2, 3, 4, 5)3/ of room-and-pillar operations have been made in this country. Although descriptions and results of experiments of mechanized longwall operations in the United States have been published (6, 7, 8), this is the first instrumented study of roof behavior on a longwall operation. In view of the possible widespread application of this method of mining to American coal mines, where underground mining conditions are different from those found in European mines, an investigation was conducted at a mechanized longwall operation inn the Lancashire No. 15 mine, Barnes & Tucker Co., Cambric County, Bakerton, Pa., to study the factors that affect roof control. This report describes this investigation and discusses the results. ACKNOWLEDGMENTS This investigation was made under a cooperative agreement between the Bureau of Mines and the Barnes & Tucker Co., Barnesboro, Pa., end was conducted in the Lancashire No. 15 mine located at Bakerton, Cambria County, Pa. The authors acknowledge the cooperation given by Richard Z. Todhunter, Sr., president, Richard T. Todhunter, Jr., general manager, and other mine officials and employees of the Barnes & Tucker Co. Mr. Edward Thomas, chief, Roof Control Section, Bureau of Mines, Washington, D. C., and Dr. Leonard Obert, chief, Applied Physics Branch. College Park, Md., collaborated in the planning and promulgation of the program investigation.

Jan 1, 1954

By Lloyd Williams

1. The investigation shows that the Wilder (locally known as the Bon Air No. 2) is the only known bed of commercial importance in Putnam County, although at least 5 coal horizons are known. All of the coal production now reported comes from this bed, which is found In a basin with no known coal outcrops. Further drilling in the east end of the basin should disclose the location of the eastern end of the axial trough and the lateral extent of the basin in Putnam County and adjoining areas in Cumberland County. Continuity of this deposit with that in the area in Putnam County north of Monterey is not conclusively established but may exist. 2 Known (measured plus indicated) reserves of coal, based on a minimum bed thickness of 14 inches and on 1,800 tons per acre-foot in place, are estimated at 29 million tons, as of January 1, 1953. Of this total, 28 million tons are in beds 28 inches and more thick. All born coal reserves in Putnam County me under less than 400 feet of overburden.

Jan 1, 1954

By G. R. Strimbeck

This is a report on experimental work on development of a gasification process operating at near atmospheric pressures and using finely pulverized coal entrained in oxygen and steam. The gasifier was designed by The Babcock and Wilcox Co. in cooperation with engineers of the Bureau of Mines Morgantown station. The test work discussed in this report covers the first 34 tests made in the pilot plant in which a strongly coking Sewickley-bed coal, ground to either 70 or 90 percent through a 200-mesh screen, was used.

Jan 1, 1954

By J. W. Watkins

This report describes in detail methods of making corrosion tests and chemical analyses that have been used extensively and satisfactorily in a study of plants in which various surface, waters and brines are conditioned and used for water flooding, brine disposal, and reservoir-pressure maintenance in Kansas, Oklahoma, and North Texas. The tests and analyses described were designed and adapted for use in the field in determining the relative corrosive and plugging tendencies of waters from various sources conditioned by different methods. Although the described methods were developed and used in testing oil-field waters in the Midcontinent oil-producing area of the United States, these same methods should be equally applicable to testing oil-field or highly mineralized waters throughout the world. Many of the methods used have been discussed by the writer (1)2/ previously, and some of them have been used for similar work in other laboratories. Early in the development of the practice of the subsurface injection of brines for disposal and increasing the recovery of oil, it became evident that different methods of chemical treatment and conditioning equipment would have to be devised to sustain desired injection rates into water-input wells. These changes became necessary because the highly mineralized waters produced with petroleum from deep formations became chemically unstable when pumped to the surface, owing to loss of dissolved gases as pressure and temperature dropped to atmospheric and to the contact with atmospheric oxygen at the surface.

Jan 1, 1954

By W. S. Sanner

This report describes the commercial application of the launder screen in anthracite-industry fine-coal cleaning operations. No new device, the launder screen has been used since the early part of the present century to size, screen, classify, and deslime the fine-anthracite sizes (Buckwheat Nos. 1 through 5) recovered by "river-coal" men dredging along streams draining the anthracite fields. The launder screen is stationary, has no moving parts, requires ample water for operation, and can be constructed economically on the job. Essentially, it consists of a wooden trough with baffles placed through its width to form a well system. The wells are covered by fine-mesh woven-wire screening. Each well is tapped with a number of orifices, and the hydraulic suction head developed in this manner removes high-gravity fines and slimes through the screening as underflow to waste. Material retained on the screen surface discharges as overflow product.

Jan 1, 1954

By R. R. Allen

[The utilization of Western coals and lignite is a continuing study of the Bureau of Mines, and storage of these fuels is of paramount importance. Since the seasonal demand for coal in the Western States triples between the summer and winter months, successful storage of these low-rank fuels would tend to level out this variation and should reduce fuel costs. The time is rapidly approaching when the West Coast States, particularly California, will annually import several million tons of coal from the Rocky Mountain States for additional power production. This will necessitate storage of large quantities of coal, and it is thefore important to develop experience in such storage. Dry surface storage, by virtue of its flexibility and low cost, is particularly adapted to the stockpiling of large quantities of coal. This report will, therefore be primarily concerned with such storage. Inasmuch as the problems of dry, open-pit storage are quite similar to those of surface stockpiling, experiences in pit storage will be discussed briefly. Although spontaneous combustion is a hazard in storing coal, experience has proved that heats can be avoided by proper stockpiling procedures. The purpose of this report is to show that the most reactive coals can be stored satisfactorily on the surface by avoiding segregation and by thorough compaction.]

Jan 1, 1954

By R. W. Smith

The Bureau of Mines has been engaged in a systematic evaluation of the thermodynamic properties of combustion gases. These studies were designed to provide basic thermodynamic information of high accuracy, facilitating the theoretical study of flame and combustion phenomena.4 This report is the fifth of a series5/ presenting results of the study for particular fuel-oxidant systems. These calculations have as their objective the constant pressure flame temperature of acetylene-air for a range of pressures.

Jan 1, 1954

By O. C. Blade

This report on the properties of aviation gasolines and aviation jet fuels produced in the United States during 1953 was made under a co-operative agreement between the American Petroleum Institute and the Bureau of Mines of the United States Department of the Interior. Analytical data are presented for 101 samples of aviation gasoline which include, for the second time in this series of reports, data on some samples of grade 108/135 aviation fuel. Data also are given for 32 samples of aviation jet fuel. The analyses were made on samples typical of the manufacturers' production in their laboratories and the results sub-mitted to the Bureau of Mines for compilation. The products of 19 manufacturers of aviation gasolines and of 19 producers of aviation jet fuels are represented.

Jan 1, 1954

By Joseph J. Wallace

1. The investigation shows that nine coal beds have been mined in Harlan County, of which the Harlan and Upper Elkhorn No, 3 are the most important from the standpoint of present production. Of less importance are the Hindman, Flag, Haddix, Wax, Fire Clay, Armburgy, and Upper Elkhorn No. 2. The Harlan, Upper Elkhorn No. 3, and Upper Elkhorn No. 2 beds contain the largest remaining known reserves. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 tons per acre-foot of coal in place, are estimated at 2,138 million short tons as of January I, 1932. Of this total, 1,956 million short tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study, Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1954

By R. G. Dressler

The design and operation of the Koppers powdered-coal gasifier and its auxiliaries at Louisiana, Mo., are described. This unit was designed to convert 1 ton of coal per hour with oxygen and superheated steam into synthesis gas - primarily carbon monoxide and hydrogen. The first run was made on May 4, 1949. After this, 44 short runs (less than 8 hours each) and 1 long run (lasting 11 days) were made. Total gasification time was 420 hours. The gasifier was not cooled down during the year when these runs were made. After an initial period of test operations and equipment proving, during which 12 runs were made, the effect of numerous variables on gasifier performance was studied. The long run was made primarily to check the equipment in sustained operation. Detailed data from these runs are presented.

Jan 1, 1954

By A. J. Barry

An apparatus and procedure have been developed for testing the anchorage effectiveness of slotted-type bolts. The apparatus consists of: (1) A hydrualic Jack assembly for loading the bolt and (2) a device (extensometer or cathetometer) for measuring displacement of the bolt as it is loaded. This apparatus and procedure permit measurment of anchor slip for loads up to the yield load of the bolt. Two representative makes of slotted-type bolts (a total of 94 bolts) were tested in typical sandstone and shale mine roof. Analysis of the test results showed that (1) anchorage capacities up to the yield load of the bolts can be developed in either rock type; (2) the shape of the slotted end of the bolt affects the ease with which the bolt can be driven; (3) all bolts for which the driving distance was more than 1.25 inches produced satisfactory anchorage in both rock types (thus, driving distance can be used as a criterion for satisfactory anchorage); (4) for the group of bolts that was satisfactorily anchored the anchor slip was unaffected by the type of bolt but was considerably larger in shale than in sandstone; and (5) the bolt expansion, that is, the amount the wedge expands the prongs in excess of the diameter of the hole, can also be employed as a criterion for satisfactory anchorage. Although the bolt-expansion and driving-distance results do not differ appreciably, the latter is recommended because it is easier to determine.

Jan 1, 1954

By O. C. Blade

This report on the properties of motor fuels sold through service stations in the United States was made in accordance with a cooperative agreement between the American Petroleum Institute and the Bureau of Mines of the United States Department of the Interior. By agreement with the American Petroleum Institute, identification of the items is confidential. It presents analytical data for 4,421 samples, representing the products of 131 companies. The samples were collected during June, July, and August, 1953. As in previous surveys, the gasolines covered by this survey include those from both large and small suppliers. The data were obtained by laboratories of various refiners, motor manufacturers, and chemical companies and submitted to the Bureau of Mines for compilation. A list of the National Motor-Gasoline Survey reports published during the past 10 years is given on page 5.

Jan 1, 1954