Search Documents

By N. H. Coates

A small, special-purpose centrifugal compressor was developed to circulate 60 pounds per hour of helium at 1,000° F and 250 psig because standard, commercial units were not available. Performance characteristics of this compressor were determined at helium flows of 2,000 to 18,000 std cu ft per hour, pressures of 100 to 250 psig, and temperatures of 100° to 1,000° F. This range is 2 to 90 actual cu ft per minute. Several graphs show the adiabatic head developed by the compressor over this wide flow range at various combinations of temperature and pressure. A compressor performance map relates pressure ratio to mass flow, temperature, pressure, and speed. This map can be used to accurately predict compressor performance factors within the range of operating conditions covered by the experiments.

Jan 1, 1963

By J. F. Messerly

The purity of three specially prepared samples of benzene was determined with an adiabatic, low-temperature calorimeter with automatic control of shield temperature. Extensive measurements were made on each sample to determine how variations in operating procedures affect melting-point and freezing-point as well as purity data obtained by the calorimetric method. Detailed results of the investigations are presented, and effects of different operating procedures are discussed, together with problems encountered in interpretating experimental results.

Jan 1, 1963

By Michael Sokaski

A dense-medium cyclone pilot plant was built to clean 112-inch to 0 size coal. This pilot plant does not require the removal of the extremely fine material (usually minus 1/2-mm) from the feed, which is necessary in conventional dense-medium cyclone plants. The essential difference between conventional cyclone plants and the pilot plant is in the medium-recovery system. The latter uses a combination of sieve bend screens, classifying cones, and magnetic separators for medium recovery. Eight tests were run in the pilot plant at a feed rate of 5 tons per hour with four different raw coals and one crushed jig middling product. Sharp separations were obtained as indicated by an average error area of 27 and probable error of 0.047 for the 112-inch to 200-mesh size range. Magnetite loss averaged about 2.5 pounds per ton of feed. The influence of several factors on cleaning performance of the cyclone was investigated. The diameters of both the overflow and underflow orifices were found to be important for optimum cleaning performance, but these diameters could vary over a wide range without serious effect; however, if this range was exceeded, cleaning performance deteriorated. Better cleaning performance was obtained when the cyclone inlet pressure was increased from 9 psig to 13 psig. The size of the magnetite particles in the medium was found to have a substantial effect, and the best cleaning results were obtained with grade B magnetite. Demagnetizing the magnetite in an effort to decrease the effective particle size did not improve cyclone performance.

Jan 1, 1963

By Thomas E. Green

A combined solvent extract ion-spectrophotometric method for the determination of as little as 1 ppm of copper in tungsten metal or tungstic oxide has been developed and evaluated. Metallic samples are converted to tungstic oxide by treatment with hydrofluoric and nitric acids. The oxide is then dissolved in sodium hydroxide, and the copper is extracted as the colored neocuproine complex. Total elapsed time for the analysis is approximately 1-1/2 days; however, actual working time for a group of six or eight determinations is less than 4 hours. Precision at the 2-ppm level is better than 0.1 ppm.

Jan 1, 1963

By Martin H. Rogoff

The presence of antibiotic materials extractable with polar organic solvents was demonstrated in coals of various ranks. Since these antibiotics occur in low concentrations, 200 pounds of a high-volatile C coal was extracted with acetone at room temperature to obtain sufficient material for detailed study. The biologically active materials in the extract were concentrated by extracting with aqueous sodium hydroxide. The fractions soluble in sodium hydroxide inhibited bacterial cultures when present in concentrations comparable to those at which other antibiotics are active (5 µg/ml). Steam distillation of the extracts did not yield highly active materials, contrary to the finds of other investigators. Mass spectrometry of the extract indicated, mainly, the presence of 6-ring compounds in the region of mass 324 to 392. The predominance of 3-ring aromatic systems found by ultraviolet analysis suggests compounds such as biphenanthryl or similar structures. The activity of the hydroxide- soluble material decreased markedly when the phenolic hydroxyl groups were transformed into trimethylsilyl ethers. Hydrolysis of the ethers yielded a product having the same activity as the original material, which indicates that phenolic compounds are largely responsible for the antibiotic activity observed.

Jan 1, 1963

By NIOSH NIOSH

This work explores application of a double alkaline leach method to extraction of alumina from Oregon ferruginous bauxitic materials. The process recovers a greater proportion of alumina from high-silica ores than is possible by a conventional single-leach method. This recovery is accomplished by calcining the ore, removing reactive silica in a preliminary dilute caustic soda leach, and then applying a second leach to dissolve alumina. Ores containing up to 15 percent Si~) 35 percent AI;:) Os, and 30 percent Os were examined. Under conditions of treatment established by experimentation, more than BO-percent alumina extraction was demonstrated. When and if conditions demand the use of low-grade materials, the double-leach process is capable of providing millions of tons of alumina from Oregon ferruginous bauxite.

Jan 1, 1963

By E. G. King, W. W. Weller

Low- temperature heat capacity measurements of muscovite were made in the temperature range from 50° to 298 ° K. The entropy at 298.15 ° K was evaluated as S298.15 = 69.0 ± 0.7 cal /deg mole .

Jul 1, 1960

By J. M. Seward, W. D. Dietzman, M. E. Hawkins

Analytical studies of formation waters are widely used by the petroleum industry as an aid in solving problems such as identifying intrusive waters , corrosion studies , treating injection water , and choosing open or closed water- injection systems . The solution of a problem is often simplified when reliable analyses of the waters under consideration have been made previously . Chemical analyses and electrical resistivity measurements are presented on 267 samples from 74 fields in south Arkansas , and 199 samples from 80 fields in north Louisiana .

Jul 1, 1960

By W. R. K. Wu

Studies are reported on the structure of coal and coke with the graphical , statistical densimetric method based on the relation between the molecular volume per carbon atom ( M / C ) and the atomic hydrogen - carbon ratio ( H / C ) . Previous work , mostly from chemical and physical investigations , is critically reviewed . Difficulties in evaluating the ring increment are demonstrated for coal and coke for the statistical densimetric method based on the additivity of atomic volumes of constituent elements . A new diagram is presented for the graphical method . Methods are introduced for correcting M /C and H/C for the presence of minor constituents in coal and coke . With the graphical method , the fractions of aromatic carbon atoms in the total carbon atoms are estimated for a coal , a resin , and 5 petrographic components ; the types of condensed structure in the fundamental units of molecules are discussed for these substances , 28 coals , and 6 " average " cokes at 500 ° to 1,000 ° C. It is also shown that the number of rings in the fundamental units of coal generally increases with increasing rank and that of coke , with increasing carbonization temperature .

Jul 1, 1960

By C. J. Chindgren, L. C. Bauerle, J. B. Rosenbaum

Modifications of the conventional method of preparing ductile vanadium metal by calcium reduction of V2 05 in a bomb were explored for clues to a more economical procedure . The modifications examined included ( 1 ) omitting the gas purge of the bomb ordinarily used for eliminating atmospheric nitrogen , (2 ) using low- grade vanadium feed materials , ( 3 ) using alternative reductants , such as aluminum , magnesium , and silicon , and reductant mixtures , and ( 4 ) bomb refining of aluminothermic metal produced in open- vessel reductions . The most promising modification appeared to be bomb refining , using calcium to purify vanadium metal -- of low aluminum but high oxygen content-- prepared by open- vessel aluminothermic reduction of vanadium pentoxide .

Jul 1, 1960

By F. W. Hoertel

The Bureau of Mines investigated the use of depleted uranium as a sacrificial anode for the cathodic protection of submerged and underground structures of iron , steel , and copper . Uranium-metal couples were tested in simulated marine environments of varying oxygen contents at pH values between 5.5 and 8.5 and under simulated boiler service condition in Rolla , Mo. , city water . Similar couples were tested in samples of Missouri soils to simulate underground service . Uranium remained anodic to iron , steel , and copper in the simulated marine environments and under simulated boiler service if the electrolyte was oxygen- free city water . Uranium appeared to offer limited protection to iron , low- carbon steel , stainless steel , copper , and zinc in the simulated underground tests . Uranium anodes offer a space advantage because 1 cubic inch of uranium gives approximately the same protection as 2 cubic inches of magnesium or 1-1 /2 cubic inches of zinc .

Jan 1, 1963

By F. E. Brantley, D. M. Yergensen, D. A. Martin

Fluidized - bed roasting was investigated as a means of decomposing gypsum and gypsum mixtures to produce a gas rich in sulfur dioxide and a lime or portland cement residue . Ninety- eight percent desulfurization of gypsum in a 10 - inch fluidized- bed reactor took 1.5 hours at an operating temperature between 1,200 ° and 1,225 ° C. A cement- type residue was obtained but had to be refired at 1,450 ° C before mortar prepared from it met the physical specifications for cement .

Jan 1, 1963

By K. K. Kelley, L. B. Pankratz, W. W. Weller

Mullite is a substance of prime importance in ceramic technology . Despite this fact , its thermodynamic properties have received little attention . A Bureau of Mines literature survey disclosed the absence of lowtemperature heat capacity data , the absence of an experimental entropy value for 298.15 ° K , and the lack of heat content data beyond the temperature range from 298° to 576 ° K. Data supplied in this Bureau report fill these gaps in the thermodynamic knowledge of mullite . According to equilibrium phase studies of Aramaki and Roy ,3 the mullite phase melts congruently at 2,123 ± 15 ° K , and the equilibrium crystallinephase composition extends from Al Si2013 to Al6.8 Si₂ Q4.2 . The results in this report are for the stoichiometric composition , Al Si¿Qз . • Heat capacity measurements were made over the temperature range from 50 ° to 298 ° K , and the entropy at 298.15 ° K was evaluated . Heat content measurements covered the temperature range from 298 ° to 1,800 ° K. Heat content

Jan 1, 1963

By R. V. Lundquist

The Bureau of Mines made a laboratory study of the amenability of anorthosite rock ( from the San Gabriel Mountains , Los Angeles County , Calif . ) to treatment by the lime soda sinter process for the extraction of alumina . The study was done under a cooperative agreement with the California Division of Mines and Geology . This report presents the results of the investigation , and it includes a review of the geology of the deposit ( 7 ) by Dr. Gordon B. Oakeshott . Interest in the recovery of alumina from submarginal aluminum silicate ores is stimulated by the fact that the domestic aluminum industry depends on imports of bauxite for its alumina requirements . Of the 8.0 million long dry tons of high - grade bauxite consumed in 1961 for producing metallurgicalgrade alumina , only 0.9 million long tons , or 11 percent , was mined in this country . During past years many organizations have carried out research programs to determine if alumina could be extracted economically from such domestic ores as clays ( 3 , 4 ) , anorthosite ( 8 ) , and other silicate sources . Successful alumina extraction is the ultimate objective of the Bureau of Mines program.

Jan 1, 1963

By E. O. Wagner, Manuel Gomez, W. S. Landers

The Bureau of Mines studied coking rates of a special Columbia - Geneva six - coal blend to establish the effect of the coking rate on coke properties . The tests were conducted in a 500 - lb , 14 - in experimental slot oven at essentially constant conditions of blend composition , size distribution , surface moisture content , and bulk density . The coking rate was varied as a function of oven flue temperature . Coking rates within the range of 0.56 to 1.35 in/hr were achieved . Increase in the coking rate decreased the size of the coke . The stability factor of the coke showed no significant change with coking rate until coking rates greater than 1.0 in/hr were reached , after which a decrease in the stability factor was observed . The apparent specific gravity increased to a maximum value at coking rates approaching 1.1 in/hr and decreased sharply with further increase in the coking rate . Coke parameters correlated well with the coking rate .

Jan 1, 1963

By Paul W. Johnson, Ralph C. Kirby, Frank A. Peters

An evaluation is presented for a process designed , on the basis of published work , to extract alumina as potassium alum from clay using sulfuric acid and potassium sulfate . The silica residue is separated by filtration . Ferric iron is reduced to ferrous iron , and the alum is crystallized from the solution , leaving the ferrous iron in solution . The alum crystals are separated from the solution and redissolved for feed to autoclave decomposition . In an autoclave the alum is partly decomposed to a basic alum , recovering five - ninths of the sulfuric acid and two - thirds of the potassium sulfate without using an acid plant . The basic alum is decomposed by calcining , and the potassium sulfate is then removed by washing with water . Operating costs for a plant producing 1,000 tons of alumina a day are estimated at $ 96.15 per ton of alumina . The fixed capital cost is estimated at $ 155 million . This process is not competitive under current economic conditions with the production of alumina from bauxite by the Bayer process . Improvement in leaching , basic alum decomposition , and washing could reduce the costs and improve the product which contains some potassium .

Jan 1, 1963

By D. S. Harper, C. O. Carman

A German coal planer was put in operation in the Keystone mine of the Eastern Associated Coal Corp. , Keystone , W. Va . , in August 1960 . At present , the planer is mining in the fourth panel . The blocks of coal mined were 340 by 1,900 feet in panel 1 , 340 by 1,660 feet in panel 2 , 590 by 1,900 feet in panel 3 , and panel 4 , currently being mined , is 590 by 1,900 feet . Almost one- half million tons of coal have been mined from these four panels . An 11 - man crew handles the complete planer operation and produces an average of 500 tons of clean coal per shift . Self - advancing hydraulic props are used to support the roof over the entire face . Roof control and action on all of the panels has been highly satisfactory . During periods of extreme pressure , some additional support is required in the tail entry where evidence of weight from the retreating longwall extends about 200 feet outby the face . The time lost from production by moving equipment between panels has been reduced steadily . The move from panel 3 to panel 4 required 5 days , but it is believed that even that time could be reduced .

Jan 1, 1963

By Arthur E. Bruszak, Marcel Vanpée

In many practical combustion systems ignition may occur through contact with hot burned gases . Such a process plays a vital role in flame stabilization on bluff bodies . It is also of importance in the ignition of firedamp by the hot spent gases of explosives used in mines . Also , in the communication of flames through narrow channels , a problem of practical importance in flameproofing electrical equipment , the propagation of the flame is essentially a reignition process in which hot burned gases are the agent of ignition . In the actual ignition problem a great variety of conditions may be visualized . Ignition may occur where pockets of hot gases are surrounded by cold explosive mixtures or where pockets of cold mixture may be surrounded by hot gases . Alternately , a flowing stream of combustible mixture may be initially in contact with another stream of hot combustion products , or a jet of hot gases may flow into a cold quiescent mixture ; the jet may be laminar or turbulent , continuous or discontinuous . The hot gas may also consist of the oxidant ( air for instance ) and the cold combustible pure fuel . This study by the Bureau of Mines is concerned only with ignition produced by a continuous jet of gas ( hot ) flowing into a practically quiescent cold mix- The investigation of ignition by bursts of hot gases or by turbulent jets is outside the scope of this report , and work performed on this phase of the problem has been published elsewhere

Jan 1, 1963

By T. E. Gray, A. W. Deurbrouck

This report describes the preparation characteristics of significant coalbeds in Kanawha County , W. Va . It is one in a series of Federal Bureau of Mines reports planned to determine coals suitable for producing metallurgical coke , either as mined or after beneficiation . Almost 9.4 million tons of coal was produced in Kanawha County , W. Va . , in 1959 , of which about 67 percent was cleaned mechanically in 10 cleaning plants . It has been estimated that more than 5,505 million tons remain in the county . Samples were collected from Pittsburgh , Stockton - Lewiston , Winifrede , Cedar Grove , Peerless , Upper Kittanning , Coalburg , Powellton , Eagle A , No. 2 Gas , and the Lower Kittanning beds . These beds were selected by the Bureau based on current production rates and estimated minable reserves . Float - and - sink tests of the samples collected from Eagle A , Peerless , Cedar Grove , Winifrede , and No. 2 Gas beds show that these coals at one location each are suitable for metallurgical use without washing . Lower Kittanning bed at four locations ; Pittsburgh , Stockton - Lewiston , and No. 2 Gas beds at two locations each ; and Coalburg , Powellton , Winifrede , Peerless , Upper Kittanning , and Cedar Grove beds at one location each can be upgraded to metallurgical quality by mechanical cleaning . Crushing the samples to 3/ 8- inch top size increased yields substantially at 1.30 specific gravity of Pittsburgh ( 17.5 percentage points ) and Upper Kittanning ( 13.0 percentage points ) beds and increased yield for the other beds sampled to a lesser amount . At this specific gravity , finer crushing caused In the 1.58 specific gravity float a general decrease in ash and sulfur . fractions of the other samples tested , most of the yields , and ash and sulfur contents , were lowered slightly by finer crushing .

Jan 1, 1963

By Albert W. Deurbrouck

This report describes preparation characteristics of significant coalbeds in Tazewell County , Va . In 1961 Tazewell County produced 933,110 tons of clean coal from six coalbeds ; the Lower Banner , Raven , Jawbone , Upper Seaboard , and Pocahontas No. 3 and No. 5. Samples from all of these beds , except the Lower Banner , were included in this study plus a sample from the Pocahontas No. 4 bed . Of the samples collected , only one would require upgrading to be of metallurgical quality . The coals ranged in rank from high- volatile -A to low- volatile bituminous .

Jan 1, 1963