Search Documents

By J. A. Lamonica

The Bureau of Mines conducted an environmental noise survey to determine the noise levels to which underground coal mine employees are exposed, to evaluate noise survey techniques and equipment, and to compare noise exposures using two criteria, Walsh-Healey and CHABA, for determining allowable exposures that were under consideration for the Federal Coal Mine Health and Safety Act of 1969- Time study techniques and Bureau-approved standard sound level meters were employed. The shift exposures of 20 percent of the miners studied were in excess of the safe standards established by both criteria. The shift exposures calculated using the Walsh-Healey criteria were greater than those calculated using the CHABA criteria owing to the intermittent nature of the exposure. Ultimately the CHABA criteria were rejected, and the Walsh-Healey criteria were adopted.

Jan 1, 1971

By L. B. Pankratz

Enthalpies above 298° K were investigated for four crystalline sodium borates by copper-block drop calorimetry. Determinations were made to 1,200° K for NaB02, 1,003° K for Na2B407, 1,005° K for NaB305, and 1,046° K for Na2Be013. No phase transitions or other thermal anomalies were found. The enthalpy determinations, when combined with known heats of formation at 298° K and other supplementary data, enabled the calculation of the heats and free energies of formation of the compounds to their melting points. Values of relative enthalpies, entropies, heat capacities, free energy functions, enthalpies of formation, free energies of formation, and equilibrium constants of formation were tabulated at even temperatures.

Jan 1, 1971

By V. E. Edlund

Laboratory batch flotation tests were conducted on copper converter slags to evaluate the relative merits of recovering copper from slow-cooled versus water-quenched slags. Three slags containing 1.6, 5.0, and 6.6 percent copper were used. More than 90 percent of the copper was recovered in a rougher concentrate leaving a 0.2- to 0.3-percent copper tailings when treating slow-cooled slag. Lower recoveries and higher copper tailings ranging from 0,5 to 0.6 percent copper were obtained from quenched slag. Grindability studies were made on the respective heat-treated slags. Quenched slags proved more difficult to grind than slow-cooled slags. Cost studies showed that (1) the cost of slow cooling and crushing off-sets any advantages of higher copper recoveries from slow-cooled slag, and (2) water-quenched slag, which requires no crushing preparatory to grinding, could be treated more economically. Costs based on processing 1,000 tons of slag per day would be $1.85 per ton for quenched slag versus $2.37 per ton for slow-cooled slag.

Jan 1, 1971

By V. E. Edlund

Laboratory batch flotation tests were conducted on copper converter slags to evaluate the relative merits of recovering copper from slow-cooled versus water-quenched slags. Three slags containing 1.6, 5.0, and 6.6 percent copper were used. More than 90 percent of the copper was recovered in a rougher concentrate leaving a 0.2- to 0.3-percent copper tailings when treating slow-cooled slag. Lower recoveries and higher copper tailings ranging from 0.5 to 0.6 percent copper were obtained from quenched slag. Grindability studies were made on the respective heat-treated slags. Quenched slags proved more difficult to grind than slow-cooled slags. Cost studies showed that quenched slags can be treated at slightly lower cost than slow-cooled slags. However, the cost advantage of processing quenched slags is more than offset by the higher copper recoveries obtained from slow-cooled slags.

Jan 1, 1971

By D. A. Wilson

A cyclic leaching process was developed for selectively leaching and recovering cadmium from nickel-cadmium scrap battery waste. The six major steps in the process are the following: (1) washing the plates to remove KOH electrolyte, (2) roasting at 550° to 600° C to oxidize metallic cadmium and decompose cadmium and nickel salts, (3) leaching with an ammonium nitrate solution, (4) precipitation of the leached cadmium from solution as cadmium carbonate using CO2 gas, (5) removal of CO2 from the lixiviator by adjusting to pH 4.5, heating, and evacuating the system, and (6) removal of small amounts of leached nickel from the lixiviator using a solvent extraction technique. The regenerated lixiviator is then recycled to leach additional plates. Cadmium extraction was 94 percent and the cadmium carbonate product contained 0.14 percent nickel and 0.12 percent cobalt impurity. The leached plates were smelted to a high nickel-low iron alloy with no detectable amounts of cadmium.

Jan 1, 1971

By F. G. Horino

The Bureau of Mines conducted compressive strength tests on model pillars of selected rock types with each pillar containing a critically oriented plane of weakness. The objective of these tests was to determine if a significant increase in the strength of the model pillar could be obtained by either (1) installing tensioned rock bolts through the pillar and normal to the plane of weakness, or (2) wrapping tensioned steel wire ropes around the pillar at uniformly spaced intervals along the pillar. Equations based on Coulomb's failure criterion are developed to predict uniaxial compressive strength of model pillars that are either rock-bolted or wire-roped. Laboratory compressive strength tests on unbolted and bolted model pillars of sandstone, marble, Indiana limestone, and oil shale containing a plane of weakness oriented at 45° showed that the bolted pillars are stronger than the unbolted pillars by 84, 31, 52, and 28 pct, respectively. Laboratory compres-sive strength tests on nonroped and roped model pillars of Texas limestone, sandstone, and granite containing planes of weakness showed that the roped pillars were stronger than the nonroped pillars by factors ranging from 1.01 to 2.41, depending upon the angle of the plane of weakness and the rock type. Rocks with a low Young's modulus benefited most by the wire-roping technique.

Jan 1, 1971

By T. T. Campbell

Studies were conducted by the Bureau of Mines to develop a process for preparing thorium-magnesium master alloys or pure thorium metal by magnesium reduction of thorium tetrachloride in a semicontinuous reactor. Thorium tetrachloride was prepared in a fluidized-bed reactor by chlorination of thorium oxide or thorium oxalate. Conditions were established for producing a suitable thorium oxide feed for a fluidized-bed reactor. Thorium tetra-chloride was purified by vacuum sublimation and subsequently reduced by magnesium in a semicontinuous reactor to form thorium-magnesium alloys. Relatively pure thorium was produced by removing magnesium from the alloys by vacuum sublimation. Close to 100 percent of the thorium fed into the reactor was recovered either as metal (~93 percent) or as thorium oxide (~7 percent). The oxide can be recycled directly into the process.

Jan 1, 1971

By P. R. Tisot

Structural response and/or deformation was determined for each of four different grade Green River oil shales (27.0-, 34.5-, 45.5-, and 63.5-gal/ton) as they were heated in an inert atmosphere, under constant compressive stress, from ambient to subretorting temperatures; that is, below those required for rapid pyrolysis of the organic matter. Small cores and small columns of confined fragments comprised the test specimens, which were heated, in a specially designed microunit, at a uniform rate either to 725° or to 825° F under three different stress levels, 80, 200, and 325 psi. Structural response of some cores was observed as they were heated in a stress-free environment. The obtained stress-strain-time-temperature relationships provide information regarding the oil shale's yield temperature, yield stress, rate of compressive strain, loss of mechanical strength, and nature of structural deformation. Effects of structural deformation on induced permeability in small columns of fragments are presented. Results indicate that underground retorting of Green River oil shale may be seriously impaired through loss of induced permeability brought about by structural deformation of rich oil shale under the influence of heat and compressive stress.

Jan 1, 1971

By William G. Pariseau

A small displacement-small strain finite element technique utilizing the constant strain triangle and incremental constitutive equations for elastic-plastic media that are nonhardening and obey a Coulomb yield condition has been applied to the analysis of gravity flow initiation in a V-shaped hopper containing a powder under lunar environmental conditions. Three methods of loading were examined. Of the three, the method of computing the initial state of stress in a filled hopper prior to drawdown by adding material to the hopper layer-by-layer is superior (as expected). Results of the analysis of a typical hopper problem show that the initial state of stress, the elastic moduli, and the strength parameters have an important influence on material response subsequent to the opening of the hopper outlet.

Jan 1, 1971

By John P. Conway

This Bureau of Mines investigation was undertaken to determine the feasibility of lock-bolt support in Tertiary-gravel material. Pull tests were performed on five types of rock-bolt anchors to determine their optimum anchorage capacity. Four of these anchors are commercially available; the fifth, an explosive-anchor bolt, was developed by the Bureau of Mines. To increase anchorage capacity, epoxy grout was used with several of the commercial types of bolt. Tests showed that sufficient anchorage could be obtained by employing epoxy-resin grout with the commercially available wedge bolt, or by using the explosive-anchor bolt. Also estimated are bolt spacing and cost of a rock-bolt support system.

Jan 1, 1971

By John M. Gomes

The Bureau of Mines investigated two techniques for removing CaO from scheelite (CaW04) prior to electrolysis. In the first technique, a crude tungstic oxide (WO3) containing 0.15-percent lime (CaO) was prepared by digesting scheelite concentrates in hot hydrochloric acid. This oxide was used as cell feed to produce tungsten of 99.9-percent purity. The second technique used a high-temperature, two-phase separation, resulting in extraction of 99 percent of the WO3 in the halide-tungstate phase, while 90 percent of the CaO was retained in the silicate phase. Tungsten of 99.9-percent purity was deposited from the halide-tungstate melt after B203 and NaPO3 were added to form an electrolyte. The two methods were compared with a previously developed technique of depositing tungsten from scheelite concentrate fed directly to the electrolytic cell.

Jan 1, 1971

By D. W. Mitchell

This Bureau of Mines report summarizes experience and past research on methods for sealing abandoned areas of a coal mine and areas from which the pillars have been wholly or partially extracted. The Federal Coal Mine Health and Safety Act of 1969 requires that such areas be ventilated or sealed with explosion-proof bulkheads, but the present study indicates that bulkheads alone cannot isolate areas in a coal mine in which methane and other dangerous gases have accumulated. Gas-air exchanges between sealed and open areas must be controlled.

Jan 1, 1971

By L. B. Pankratz

Low-temperature heat capacities, high-temperature enthalpy increments, and the enthalpy of formation at 298° K were determined calorimetrically for vanadium subnitride (VN0.465). The low-temperature investigation gave S°298.15 = 6.379 ±0.005 cal/deg mole, and a combustion calorimeter investiga¬tion provided ?Hf°298.15 = -31.80 ±0.60 kcal/mole. The two quantities were combined with the high-temperature data to give standard values of enthalpies of formation and free energies of formation above 298° K. These and related thermodynamic functions were tabulated to 1,800° K. Similar data are included in the range of 298° to 1,600° K for the mononitride, VN.

Jan 1, 1971

By Larman J. Heath

Liquid incendiaries were burned within the interstices of several different types of sandstone cores to determine the technical feasibility of increasing sandstone permeability by this method. Fuel-oxidant mixtures were tested in 186 cores; six cores exploded when ignited. In virtually all instances, the explosion completely pulverized the sandstone cores. In addition n those cores damaged by explosions, 24 cores were fractured so severely that permeability tests were impossible. Although combustion gener¬ally increased the permeability, specific mixtures at given pressures were inconsistent in their ignition and burning behavior. Tests indicated that the heat of burning incendiaries significantly increased sandstone permeability. The improved permeability ratios were usually less than 2, but one was 10.3. Permeability alteration by other in situ methods was not as effective as that by flame propagation.

Jan 1, 1971

The Bureau of Mines has long been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heating value of the coal, expressed in British thermal units, and the composition as shown by proximate analyses. To these, when required, are added the ash-softening temperature, the free-swelling index, and the Hardgrove grindability index. Under most of these specification contracts, the bidders guarantee the quality of the coal, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instructions1 issued by the Bureau of Mines, and the samples are analyzed in the Bureau laboratory to determine whether the coal is of the quality guaranteed by the contractor; if it is not, a price adjustment is made. The Government, with the exception of the Tennessee Valley Authority, purchased approximately 5.5 million tons of coal in fiscal year 1971. In connection with these purchases, the Bureau analyzed 4,366 samples. These are published (table 1) for the use of Government officials and the public. Such analyses of delivered coal and tipple samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) provide valuable data for use in evaluating future bids. In addition, the continuous sampling of coal as delivered is a check on the practical results obtained in burning the coal.

Jan 1, 1972

By Verne E. Hooker

Near-surface temperature measurements in two granite quarries show that diurnal temperature variations are significant to a depth of 1 or 2 feet, and annual temperature variations are significant to a depth of at least 25 feet. As a result, ground stress anomalies due to temperature exist near the surface, and their magnitude depends upon the time of day and the time of year. Rock stress and corresponding temperature measurements were made in one granite quarry over a rock temperature range of 33° to 81° F. Measured rock temperatures show good agreement with values predicted from one-dimensional heat flow theory. Calculated and measured stress-temperature coefficients for the two granites in this study are given. Thermally induced stress variations in near-surface rocks tested were as large as 1,690 psi from combined daily and seasonal temperature changes.

Jan 1, 1971

By D. G. Kuehn

Positive ion sampling studies have been conducted on do discharges containing 0.33 percent sulfur dioxide in helium. Measurements were made for normalized gas pressures from 0.45 to 6.8 torr and discharge currents from 5 to 40 ma. Ion species observed included SO+, S+, SO2+, SO3+; O+, and 0+, 02+. Studies were conducted on the functional dependence of the various ion species with respect to axial distance, pressure, current, and gas flow rate. Interpretation of these results is consistent with the assumption of SO2 dissociation. Deposition of sulfur compounds was observed in the plasma container during these studies. The present results are compared with previous studies which have been conducted in SO2.

Jan 1, 1971

By Thomas E. Green

A gas volumetric method was developed for determining metallic aluminum at the 0.01-to 0.3-percent level in 100-gram samples of recycled glass. The method is based on the measurement of the change in gas volume produced by the reaction 2 Al + 2 NaOH + 2 H2O ? 2 NaAl02 + 3 H2 using a simple apparatus assembled from readily available glassware. Apart from sampling errors, the precision of the method is within ±5 percent. A minor modification of the apparatus would extend the method to larger samples or samples of higher metallic aluminum content. Metallic iron and metallic zinc do not interfere at the concentrations found in recycled glass recovered from incinerator residues.

Jan 1, 1971

By J. M. Kuchta

Ignition and flammability test methods were developed by the Bureau of Mines for use in the classification of flammable solids by the Department of Transportation. A rotating disk ignition apparatus and a flame-spread-rate apparatus are proposed for determining the ignitability and flammability, respectively, of most flammable solids. Extremely flammable solids, such as pyrophoric materials, are evaluated by determining their ease of spontaneous ignition in an environmental chamber at high-humidity conditions. Data are presented for various representative solids to show the reliability of the test methods for classifying the materials. A classification system is also proposed for use in government transportation regulations.

Jan 1, 1972

By B. J. Scheiner

Oxidation procedures based on the chlorine-hypochlorite system were investigated for improving gold recovery from carbonaceous gold ores. The oxidation pretreatment prior to cyanidation was accomplished by (1) addition of sodium hypochlorite to ore pulp, (2) by addition of chlorine to ore pulp, and (3) by generation of hypochlorite in situ by electrolysis of a brine solution used to pulp the ore. Gold extraction of 90 pct was achieved by cyanidation of carbonaceous ore that had been pretreated with 20 Ib per ton sodium hypochlorite at 50° C for 4 hours. Similarly, pretreatment of the ore pulp with 35 1b chlorine per ton at 24° to 30° C and 15 hours reaction time resulted in 89-pct gold extraction by subsequent cyanidation. Concomitant studies showed that electrolyzing the pulp prepared with a brine solution was equally as effective as electrolyzing hypochlorite and chlorine for oxidizing carbonaceous ore constituents that are deleterious to cyanidation. Gold extraction of 90 pct was obtained by electrolysis when 275 lb of are was treated at 200 amp for 7 hours in an 8-to 10-pct salt solution. Power consumption was in the range of 60 kwhr per ton.

Jan 1, 1972