Search Documents

By William J. Campbell

This analytical method development and evaluation was undertaken by the Bureau of Mines to provide accurate determinations of eight minor elements in low-alloy steels prepared from ferrous scrap. Fluorescent X-ray spectrography was the principal method investigated. Confirming analyses were made by conventional instrumental and chemical methods. All X-ray data were processed by a timesharing computer. No corrections were found necessary for inter-element effects or overlapping spectral lines. Concentrations were calculated from the least-square fit of a linear calibration equation derived from measurements on three sets of standard steels. These studies show that X-ray spectrographic analysis of lathe-finished surfaces provides accurate determinations of aluminum, copper, chromium, manganese, nickel, phosphorus, silicon, and tin.

Jan 1, 1973

By Laurence G. Trudell

Geology and oil-yield data are presented for a 58-square-mile area encompassing the U.S. Department of the Interior oil-shale leasing program tracts in the western Washakie Basin, Sweetwater County, Wyo. Lithology and oil yields of samples from three Bureau of Mines coreholes are evaluated and correlated with Kinney Rim surface sections measured and sampled by the U.S. Geological Survey. Minable sections of oil shale averaging up to 25 gallons of oil per ton crop out on Kinney Rim in the Laney Member of the Green River Formation. Thick oil-shale sections in the Laney Member that average 15 gallons per ton represent 155 million barrels of oil in place per square mile. In the lower part of the Green River Formation the Tipton Shale Member contains a 20-to 40-foot section averaging 15 gallons per ton. Beds of high-volatile C bituminous coal up to 6 feet thick are present in intertongued parts of the lower Green River Formation and upper Wasatch Formation.

Jan 1, 1973

By L. L. Oden

The purpose of this research was to develop a method to remove copper and tin from the magnetic fraction of incinerated municipal refuse, as recovered by the Bureau of Mines pilot plant in College Park, Md. Copper, present in the scrap in a metallic form bonded to ferrous objects, was amenable to leaching in cupric ammonium carbonate solution. Copper levels in small 5-to 10-lb lots of treated scrap were reduced from the initial level, 0.5 to 0.6 pct, to 0.1 to 0.2 pct. Larger lots of scrap (100 lb) were treated less effectively because of poor contact of solution and scrap. Oxidation in the air or in aerated aqueous solution was applied to liberate tin from the dilute solid solution present on the surface of incinerated tinplate. Shredding of air-oxidized scrap or caustic leaching of scrap oxidized in solution reduced tin levels from the initial 0.25-pct level to about 0.1 pct.

Jan 1, 1973

By Mark I. Copeland

The Bureau of Mines investigated the effect of up to 1 wt-pct of copper and silicon on the heat treatment response and hardness, tensile, and impact properties of hot-rolled medium-carbon steels. The steels were prepared by induction melting and fabricated into plates by forging and rolling. The tensile strength of 0.2-wt-pct carbon steels containing 0.3 wt-pct silicon was affected significantly by copper in both the hot-rolled and heat-treated (600° C) conditions, whereas the tensile strength of the 0.3-wt-pct carbon steels was less affected. A 600° C treatment was considered optimum as a post-rolling treatment to strengthen the steels by copper precipitation. Strengthening of 0.2-wt-pct carbon steels by silicon was reduced by increasing copper contents.. Optimum impact strengths occurred at about 0.3 wt-pct silicon in 0.2-wt-pct carbon steels containing 0.6 and 0.8 wt-pct copper. The impact strengths were lowest for 0.2-wt-pct carbon steels containing over 0.8 wt-pct copper and greater than 0.3 wt-pct silicon, especially in the heat-treated condition. Copper and silicon solutes and copper precipitates strengthened the steels. This effect was augmented slightly by strengthening through grain refinement by these solutes.

Jan 1, 1973

By L. A. Haas

Hydrogen sulfide was decomposed to elemental sulfur in an electrical discharge. With He, N., or Ar diluents, a threshold voltage between 1 and 3 kV was required for the decomposition reaction to occur in a laboratory ozonizer. Above the threshold voltage, the HAS decomposition rate increased with increasing voltage, but the increase was more pronounced with argon diluent than with either nitrogen or helium. In common with other reactions in an electrical discharge, the B2S decomposition decreased with increasing temperature in the range of -410 to +61° C. The reaction did not appear to be rate-controlled by a solid-gas sorption step because the introduction of activated charcoal into the electrical discharge zone did not significantly affect the decomposition yield. In the presence of polymeric chlorofluoro-carbon oil, 90 pct conversion of the 3 pct H2S in helium was obtained at 14 kV, 60 Hz, a 2-mm electrode gap, and a gas-residence time greater than 1 min. Under the same experimental conditions in the absence of oil, the conversion was only about 50 pct.

Jan 1, 1973

By Charles W. Huggins

To determine the nahcolite and dawsonite content in oil shales, the Bureau of Mines compared X-ray diffraction, infrared spectroscopy, thermal methods, and a previously published method by Smith and Young based on the selective solubility of sodium compounds. The Smith and Young method and a new method based on the weight of carbon dioxide produced by thermal decomposition are recommended for determining nahcolite. X-ray diffraction and the Smith and Young method are recommended for determining dawsonite. X-ray diffraction, infrared spectroscopy, and differential thermal analysis were useful for identifying other minerals in the samples.

Jan 1, 1973

By Joseph Grumer

In addition to nine powder and gaseous extinguishants of propagating Pittsburgh seam coal dust-air explosions earlier evaluated,6 10 other powders have similarly been evaluated under like conditions such that wall quenching of the coal dust-air flames was virtually absent and the dust concentration was temporally and spatially uniform to within about ±5 percent. None of the newly examined extinguishants was better than Purple-K (potassium bicarbonate); the 10 of this report are anhydrite (calcium sulfate), monobasic (4 types) and dibasic ammonium phosphate, natural and synthetic cryolite (sodium fluoalumi-nate), sodium sulfate, and tricalcium phosphate. Except for anhydrite, sodium sulfate, tricalcium phosphate, and the cryolites, these materials were about equally effective, when present in relatively low concentrations (weight-percent of the coal dust-extinguishant mixture). The maximum oxygen concentration for the extinguishment of otherwise uninhibited coal dust explosions and the influence of coal dust particle size and the volatile content of the coal were also explored. For the present, the choice of the inhibitor among the good ones evaluated is not as critical as the system to be used to deploy the extinguishant against a coal dust explosion.

Jan 1, 1973

By E. L. Burwell

Application of the in situ recovery process to oil shale was tested during two field experiments near Rock Springs, Wyo. The results of these tests demonstrate that a self-sustaining combustion zone can be created in an oil shale body, that this zone can be moved through the oil shale, and that the process will produce shale oil. Evaluation of the combustion process by monitoring produced fluids for physical and chemical properties and volumes is described. The material and energy balance obtained is compared with a second evaluation based on extensive coring of the test area after the test was terminated. Several side results of the research are noted such as ground surface heating by underground burning and production of low-to medium-Btu gas during retorting.

Jan 1, 1973

By J. W. Walkiewicz

Studies were conducted by the Bureau of Mines to develop a method for fabricating Sm-Co permanent magnets. This method consisted of arc-melting, crushing and grinding the alloy, alining and pressing the powder, and sintering the green compacts. Results indicated that the optimum composition was 36.7±0.3 weight-percent Sm and 63.3±0.3 weight-percent Co. This composition was obtained by blending together Sm2C07 and SmCo5. The maximum values exper¬imentally obtained were MHC = 27.4 kOe, BHc = 7,510 Oe, Br = 7,810 G, and (BH)max = 15.1 MGOe. The optimum sintering temperatures and grinding times for maximum MHc and (BH)max were determined. Lowering the grinding temperature from 0° C to -60° C resulted in a significant increase of magnetic properties.

Jan 1, 1973

By Parviz F. Rad

The increased use of tunnel boring machines (TBM) has stimulated laboratory research to optimize the cutting parameters of these machines with the objective of increasing machine efficiency and penetration rate. Laboratory-scale rock cutting experiments have succeeded in identifying many of the important parameters involved in rock-cutter interaction. Although scaling factors may be required to apply the results directly, the concepts developed can be used qualitatively as design guidelines for boring machines. The Bureau of Mines Twin Cities Mining Research Center has recently developed a large-scale rock cutting device (RCD) that will simulate many of the operating parameters of the tunnel boring machines in the laboratory under a controlled environment. The results of the experiments with this device will be directly applicable to the design of TBM's.

Jan 1, 1973

By Robert I. Fujimoto

The work described was conducted to develop standards for the application of wire rope clips on wire rope. These standards include optimum number of clips and clip nut torques for wire rope sizes 1/4 through 2-1/4 inches, when used for forming an eye attachment in wire rope. Wire rope test specimens with clip attachments were load tested on tensile testing machines to determine an effective combination of clip nut torques and number of clips for each size of wire rope to develop efficiencies above 90 percent of the catalog ultimate rope strength.

Jan 1, 1973

By T. Christos

The explosive oils, nitroglycerin (NG) and ethylene glycol dinitrate (EGDN), were extracted from dynamites by a halocarbon solvent and were then determined by high-pressure liquid chromatography. Separation was achieved by liquid-liquid chromatography on a column packed with Durapak-Carbowax 400/Corasil II and the eluted NG and EGDN were detected with a double-beam ultraviolet detector.

Jan 1, 1973

By J. J. Drost

This Bureau of Mines investigation studied the effect of thermal treatments upon concentratability of a western Mesabi Range nonmagnetic taconite ore and is a sequel to Bureau of Mines RI 7567. Magnetic tube tests were used to develop the data needed to calculate separation efficiency, the primary measure of concentratability. A horizontal tube furnace was employed to heat treat and reduce the hematitic ore samples. The two variables studied were roasting temperature and cooling method. The manner of cooling, either by slow cooling or quenching in water, produced no significant difference in concentratability. Roasting temperatures employed ranged from 500° to 1,000° C, and a temperature of 650° C effected the best concentratability. The temperature of 650° C correlated with the most effective roasting temperature for grindability.

Jan 1, 1973

By Martin S. Oudenhoven

This Bureau of Mines report presents the results of a microseismic study conducted in the Climax block cave mine at Climax, Colo. Rock noises created by caving were monitored and their sources located during a 3-month period. A planar array of seven accelerometers, located above the block of ore being caved, detected the rock noise. A computer was used to calculate the location of the microseismic activity, using a traveltime difference method. The accuracy of these locations was estimated to be ±20 feet. An analysis of the data taken during the recording period showed a concentration of microseismic events located in the wall of the cave panel. This concentration of events was found to occur in a "high-silica" geologic forma-tion that cut across the caving panel approximately 200 feet behind the undercut.

Jan 1, 1973

By Rees D. Groves

The Bureau of Mines conducted research on reactions of copper sulfide minerals with chlorine in an aqueous system. Selected samples of covellite, chalcopyrite, chalcocite, bornite, and pyrite were leached with aqueous chlorine solutions. The mineral samples were sized on to minus 100- plus 325-mesh, individually mixed with precleaned sand and leached in an enclosed percolation column. Each mineral was leached in stages to achieve about 90 percent mineral dissolution. The chlorine leaching solutions were produced by reacting sodium hypochlorite with hydrochloric acid within the closed system. The study showed that when the mineral dissolution was complete, the reaction products (copper, iron, and sulfur) were in their highest oxidation states and a stoichiometric amount of chlorine was consumed. Although elemental sulfur formed as an intermediate product, it was oxidized to sulfate during the leach.

Jan 1, 1973

By Stephen Krickovic, J. E. Carpetta, T. D. Moore

Air quantity-pressure and methane concentration surveys were conducted by the Bureau of Mines in accessible portions of an area being pillared in a Pittsburgh coalbed mine in West Virginia. These included two mined-out and three active butt headings and a bleeder system. The particular mine workings were started in virgin coal directly from a set of main headings; the main reason for the study was the difficulty usually encountered in adequately bleeding the gobs under such conditions. Although the two separate return airways in each active butt heading and the North and 1 Left bleeders contained acceptable methane concentrations (0.01 to 0.78 percent in the butts and 0.73 to 1.0 percent in the bleeders) with significant total methane removal (109 cfm in butts and 631 cfm in bleeders), there were relatively large areas in the gobs with possible minimal airflows. This condition appears to have developed from lack of systematic regulation of the airflow across the gobs and appears to indicate the existence of considerably more methane in the probably low flow areas in the gob.

Jan 1, 1973

By Stephen Krickovic

Air quantity-pressure and methane concentration surveys were conducted by the Bureau of Mines in accessible portions of an area being pillared in a Pittsburgh coalbed mine in West Virginia. These included two mined-out and three active butt headings and a bleeder system. The particular mine workings were started in virgin coal directly from a set of main headings; the main reason for the study was the difficulty usually encountered in adequately bleeding the gobs under such conditions. Although the two separate return airways in each active butt heading and the North and 1 Left bleeders contained acceptable methane concentrations (0.01 to 0.78 percent in the butts and 0.73 to 1.0 percent in the bleeders) with significant total methane removal (109 cfm in butts and 631 cfm in bleeders), there were relatively large areas in the gobs with possible minimal airflows. This condition appears to have developed from lack of systematic regulation of the airflow across the gobs and appears to indicate the existence of considerably more methane in the probably low flow areas in the gob.

Jan 1, 1973

A study was conducted by the Bureau of Mines to evaluate natural gas as an automotive fuel and to provide guidelines for optimum engine adjustments for low exhaust emissions. The study was conducted using a single-cylinder engine, a multicylinder engine, and a total of eight vehicles. Results from single-cylinder engine tests showed that the light-load, lean-limit misfire region for natural gas begins at an air-fuel ratio between 150 and 160 pct of stoichiometric. Changes in ignition timing significantly influenced emissions of nitrogen oxides and hydrocarbons, but had little effect on carbon monoxide emission. Low emissions can be achieved with current-design engines by adjustment of engine parameters, but only with heavy penalty to engine performance. Emissions from vehicles fueled with natural gas are virtually unaffected by ambient temperature change within the range 20° to 100° F. The organic emissions from engines fueled with natural gas were estimated to be 22 to 25 pct as reactive as the emissions produced using gasoline. Levels of exhaust emissions from vehicles fueled with natural gas were unchanged over 10,000 miles of normal driving.

Jan 1, 1973

By A. W. Hall

A nuclear method was developed for continuously and automatically deter-mining the moisture content of coal flowing through a bin. Fast neutrons from a 1 curie americium-beryllium source penetrate the coal, are thermalized (slowed down) by hydrogen in the moisture, and are counted by a thermal neutron detector. The difference between the number of these thermal neutrons and those thermalized by dry coal (in a reference drum) is a measure of the moisture content of the coal. A materials handling system was developed and in tests at a commercial coal preparation plant, moisture in coal was monitored continuously within 0.2 percent of values determined by conventional means. The meter responded rapidly to change in moisture content, making it adaptable to automatic process control, and was operated for 1 year without malfunction or recalibration. Shielding of the source by the coal kept the neutron flux level at the bin wall less than 1 milliroentgen per hour, a safe level for personnel.

Jan 1, 1973

By Jack E. Tress

The Bureau of Mines has been involved for several years in the development of processes for the recycling of solid wastes. As part of this program, a project was initiated to determine the feasibility of producing secondary pig iron from auto scrap. During the test period, 86,000 pounds of shredded auto scrap, along with petroleum coke and fluxing agents, was charged to a submerged-arc furnace of 1-ton nominal capacity. Eighty-eight thousand pounds of pig iron, with an average carbon content of 3.90 percent and an average copper content of 0.2 percent, was produced at an electrical consumption of 512 kW-hr per net ton. A cost estimate of the process showed that the pig, iron might be produced at a cost of $57 per ton.

Jan 1, 1973