Search Documents

By W. P. Diamond

Coalbeds exhibit a directional permeability, with the maximum permeability oriented parallel to the face cleat. Thus, the most efficient pattern of vertical degasification holes for a coalbed is dependent upon cleat orientation. Surface joints, infrared photolinears, and Ronchi grating photolinears were investigated as potential estimators of subsurface cleat orientation. Cleat orientations were measured in 18 mines, in the Pittsburgh coalbed in southwestern Pennsylvania and northern West Virginia to be used as a standard against which prediction techniques would be evaluated. Two cleat systems with a strong geographic segregation were measured in the study area: N 670 W -N 280 E (950 separation) for the north, and N 76° W -N 17° E (930 separation) for the south. Directional data obtained from the three techniques investigated yielded satisfactory regional predictions of cleat orientation. Analysis of surface joints was the only technique considered sufficiently reliable on a local basis. Prediction of cleat orientation is based on the pairing of the principal directional sets into all reasonable combinations of fundamental systems. The system or systems composed of the most dominant sets nearest to 90° separation are likely to be a reliable prediction of cleat orientation. The most dominant set of the system selected is likely to be the face cleat.

Jan 1, 1976

By D. A. Wilson

A laboratory method for processing lead battery scrap has been developed that eliminates virtually all of the S02 emission that normally is produced when a reverberatory or blast furnace is used. The method employs a hydrometallurgical step to convert the PbS04 to PbO and CaS04 by mixing the battery scrap with a slurry of Ca(OH)2. The reaction is exothermic and goes to completion in 2 to 5 minutes at room temperature. The dried product is mixed with a KC1-NaC1 flux and carbon and reduced at 6500 C. A minimum charge ratio of 3 parts of carbon to 100 parts of battery scrap is required for reduction. The process produces lead reductions and recoveries as high as 97.0 and 94.9 percent, respectively. The KCI-NaCl flux is recovered using a standard counter-current water leach followed by evaporation.

Jan 1, 1976

By G. M. Martinez

A cell concept adaptable to large-scale electrowinning of zirconium metal from zirconium tetrachloride was investigated by the Federal Bureau of Mines. Tests were made in twin cells, each 12 inches in diameter by 33 inches long. Electrowinning was performed in one chamber from which the electrolyte was transferred after electrolysis to the other chamber where it was renewed by the introduction of ZrC14 by direct sublimation. The formation of a salt plug in the connecting pipe provided a seal between the chambers. Optimum electrolyte composition, with respect to quality of the metal product (91 pct meeting ASTM standards except for the oxygen content) and current-carrying capability (about 350 amp) was determined to be 16.7 wt-pct NaF-83.3 wt-pct NaCl mixture plus ZrC14 equal to about 3 wt-pct zirconium. A twin-cell design incorporating the unit operations covered by this investigation is proposed.

Jan 1, 1976

By Martin Hertzberg

The concept of limit burning velocities is used to formulate a quantitative theory of flammability limits. Competing processes dissipate power from a combustion wave and quench propagation at some characteristically low limit velocity. There are four competing processes and one complication: (a) Free, buoyant convection, (b) conductive-convective wall losses, (c) radiation, (d) selective, diffusional demixing (the complication), and (e) flow gradient effects (flame stretch). These complexities are unraveled by creating an idealization that is initially freed from these competing processes. The ideal serves as a standard, and its burning velocity (Su), ideal is a unique function of the initial thermodynamic variables of state. By adding each process individually, it is possible to evaluate their significance, quantitatively, in terms of a limit velocity (Su)a , b , c , or e , and to explore the nature of their cooperative interactions. The larger the limit velocity, the more significant the process. The apparently diverse observations of flammability behavior are readily unified within this simple, conceptual framework.

Jan 1, 1976

By M. J. Ferrante

The standard enthalpy of formation, low-temperature heat capacities, and enthalpy increments above 298 K were determined by the Federal Bureau of Mines for synthetic dawsonite [NaA1C03(OH)21. The enthalpy of formation was determined by hydrochloric acid solution calorimetry, with the result ?Hf°298 = -469.4±0.7 kcal/mole. The low-temperature heat capacities were determined from 6 to 307 K by adiabatic calorimetry. Tabulated are low-temperature values of Cp°, S°, and H.-Ho° from 3 to 298 K. The derived entropy at 298 K is S298 = 31.55±0.3 cal/deg mole. Enthalpy increments above 298 K were obtained by copper-block drop calorimetry. Tabular data of Cp°, S°, H°-H°298, -(G°-H°298)/T, ?Hf°, ?Gf°, and log Kf are given from 298 to 477 K. Enthalpies and Gibbs energies of decomposition are also reported.

Jan 1, 1976

By Daryl R. Tweeton

The Bureau of Mines conducted experiments to measure the influence of environment on the friction and wear of a steel-quartz system at several speeds and loads. In each test a quartz block was pressed against a rotating ring of low-carbon steel. Environments used were moist air, dry air, dry nitrogen, water, aqueous oleylarnmonium acetate (ClsH35NH3+-OCOCH3), and aqueous aluminum chloride (A1C13). The sliding speeds were 2.2, 13, and 33, cm/sec, and the loads were 6.8 and 13.6 kg. The coefficient of friction, the wear, and the roughness of the surfaces were measured, and the wear debris was examined. The coefficient of friction was significantly lower in moist air at 2.2 cm/sec than for any other combination of environment and speed employed, and was generally an inverse function of the oxidizing ability of the environment. The coefficient of friction increased somewhat with increasing load. The wear of the steel rings was greatest in dry air at all speeds and loads. The wear of the quartz blocks at 180 rpm was greatest in dry air, but at 12 rpm it was greatest in nitrogen. Friction and wear in aqueous oleylarnmonium acetate and in aqueous aluminum chloride were similar to effect in water alone.

Jan 1, 1976

By F. P. Haver

The Bureau of Mines is developing a leach-electrolysis procedure to produce Special High Grade (SHG) zinc from sulfide concentrate without the generation of sulfur oxide gases. Chlorine-oxygen leaching of the concentrate yields zinc chloride (ZnCI2) which, after purification, is electrolyzed in a fused-salt cell to obtain molten zinc metal and chlorine gas for recycle. This paper describes a laboratory-scale investigation made to develop a procedure for electrowinning zinc metal from ZnC12. Zinc chloride by itself is not a suitable electrolyte because it fumes badly above its melting point and is a poor conductor of electricity. Other salts therefore must be added to prevent fuming and improve the conductivity. Optimum results were obtained with a KC1-LiCl-ZnCl2 bath at 500° C, using a current density of 5 amp/in2 and an electrode spacing of 0.5 inch. Under these conditions, SHG zinc was produced at a current efficiency of 94.3 pct and an energy requirement of 1.16 kwhr/lb. Fused-salt electrowinning eliminates the need to handle and melt cathodes and increases the production of metal per unit cell volume through the use of higher current densities than are possible with aqueous electrolysis.

Jan 1, 1976

By William C. McLaughlin

In the deep vein mines of the Coeur d'Alene mining district, rock bursts are a potential hazard to the mine structure and underground personnel. Damage repair costs are estimated by one company to exceed $1 per ton of ore mined. The Bureau of Mines, in cooperation with the mining companies, has conducted research intermittently over the past 10 years to help reduce bursts. Onsite inspections of major rock bursts were conducted, and reports were submitted to mine management; these included the geology and geometry of the affected area. The paper discusses the development and improvement of microseismic and surface monitoring equipment. The underground microseismic network, when operated on a regular basis and the results plotted daily, is capable of detecting stress concentration in certain areas. The surface seismographs record rock bursts, blasts, earthquakes, etc., throughout the district and show approximate location, time, and relative intensity of the event.

Jan 1, 1976

By Maria I. De Rosa

High temperatures encountered by mine rescue teams during emergency situations may cause severe physiological strain, hindering the men from carrying out rescue and recovery missions. A prototype ice-cooling garment (ICG) was developed by the Bureau of Mines to alleviate physiological strain due to heat stress. The effectiveness of the garment was tested with acclimatized and unacclimatized subjects at a typical work rate (1,200 Btu/hr) expected during rescue operations and at various hot environments (97° to 113° F dry bulb and 80° to 89° F wet bulb). During exposures with the ice cooling garment, the subjects were able to maintain a safe deep body temperature of 100.4° F or below Without the garment, the deep body temperature rose beyond values of 100.4° F, a condition considered unsafe for continuous work in hot conditions. Both heart rate and skin temperature values were lower while wearing the ICG. Subjective observation also indicated a marked benefit by wearing the ICG.

Jan 1, 1976

By G. W. Elger

This report describes pilot-plant studies and an economic evaluation of a process developed by the Federal Bureau of Mines, Albany Metallurgy Research Center, to produce synthetic rutile from a rock-type ilmenite concentrate. In this process, ilmenite blended with coke and lime is smelted in an electric arc furnace to separate most of the iron as salable pig iron and to form a titania-enriched slag of low iron content, which is treated with oxygen and titanium pyrophosphate. The titanium oxides are converted to crystalline rutile; the phosphate glass contains most of the associated impurities. The treated slag is ground and leached with sulfuric acid to liberate rutile crystals, which are concentrated by physical methods. In pilot testing conducted to obtain data for a cost estimation, a synthesized product containing about 88 wt-pct TiO2 and less than 2 pct FeO was extracted from a rock-type ilmenite concentrate containing about 45 wt-pct TiO2. The estimated fixed capital cost (on a mid-1975 basis) of a plant producing 500 tpd of synthetic rutile is $28,290,100. Based on 330 operating days per year, the estimated operating cost for this process is $351 per ton of synthetic rutile. The estimated selling price of synthetic rutile made from rock-type ilmenite is $344 per ton, based on a credit of $160 per ton of pig iron and a 20 pct interest rate of return on investment after taxes.

Jan 1, 1976

By John A. Breslin

Size distributions and concentrations of particulates emitted from diesel engine exhausts were measured with cascade impactors. Samples were taken from the exhaust of two types of engines using three types of fuel and operating under five different engine speed and load conditions. The measured mass median diameters of the diesel particulates were typically about 0.3 um. There was no significant difference in mass median diameter between engines or fuels and only a slight dependence on operating mode. Concentration measurements ranged from 14.2 to 250.9 mg/cu m, and calculated mass outputs, from 64 to 10,000 mg/min. Significant differences in mass output were found between engines, fuels, and especially between different operating modes. The quantity of clean dilution air that would be required to reduce the particulate mass concentration below the 2.0 mg/cu m respirable dust standard for coal mines was greater than the dilution air required to meet the standards for noxious gases for both engines tested.

Jan 1, 1976

By John A. Breslin

Size distributions and concentrations of particulates emitted from diesel engine exhausts were measured with cascade impactors. Samples were taken from the exhaust of two types of engines using three types of fuel and operating under five different engine speed and load conditions. The measured mass median diameters of the diesel particulates were typically about 0.3 um. There was no significant difference in mass median diameter between engines or fuels and only a slight dependence on operating mode. Concentration measurements ranged from 14.2 to 250.9 mg/cu m, and calculated mass outputs, from 52 to 3,443 mg/min. Significant differences in mass output were found between engines, fuels, and especially between different operating modes. The quantity of clean dilution air that would be required to reduce the particulate mass concentration below the 2.0 mg/cu m respirable dust standard for coal mines was greater than the dilution air required to meet the standards for noxious gases for both engines tested.

Jan 1, 1976

By Robert P. Vinson

This report describes three coal mine ventilation studies by the Bureau of Mines in which sulfur hexafluoride (SF6) was used as a tracer gas. One of these studies was conducted to determine air movement and leakage in a sealed area. Another was run to determine the ventilation efficiency of a bleeder system. Finally, a study was made of air leakage across permanent stoppings of parallel intake airways. These studies proved sulfur hexafluoride to be a useful addition to the equipment commonly used in coal mine ventilation analysis.

Jan 1, 1976

By E. E. Maust

The present work is part of an ongoing Bureau of Mines effort to provide a better understanding of the fundamental phenomena involved in sulfide flotation, the role of oxygen in xanthate adsorption being one essential issue. Galena was chosen as the material around which to develop a conceptual model, partly because of its demonstrated oxygen sensitivity and partly because information on its properties and flotation behavior constitutes the largest part of the fundamental information available on sulfides of commercial importance. The model is formulated primarily in terms of surface electronic energy levels produced by oxygen and xanthate and is further developed using existing experimental evidence and its implications. Four major functions of oxygen are elucidated, and the relationship of these to the formation of lead xanthate, dixanthogen, and a surface compound is discussed. Though yet incomplete, the model provides a useful framework within which the results of diverse experiments can be related to one another in their proper perspective, as shown by a brief discussion and resolution of some apparently discordant results reported in the literature.

Jan 1, 1976

By B. J. Scheiner

The Federal Bureau of Mines has successfully demonstrated an electrooxidation-solvent extraction-carbon adsorption process for recovering molybdenum and rhenium from offgrade concentrates. The flow sequence consists of dissolution of metal values by electrooxidation, liquid-solid separation by thickening, acidification and chlorate ion removal by sulfur dioxide treatment, solvent extraction to concentrate the molybdenum and rhenium, separation of molybdenum and rhenium by carbon adsorption, and metal recovery by crystallization. Molybdenum and rhenium were recovered as ammonium paramolybdate and ammonium perrhenate. Electrolysis of brine-concentrate pulps to generate a hypochlorite oxidizing agent in situ resulted in the dissolution of 98.9 and 99.1 pct of the molybdenum and rhenium, respectively, at an energy consumption of 13.7 kwhr/lb of molybdenum extracted.

Jan 1, 1976

By David Schlain

This Bureau of Mines report describes a method for electrodepositing titanium diboride from a molten salt bath. Initially, the electrolyte is a mixture of LiBO2, NaB02, Na2 Ti03 , Li2Ti03, and Ti02? The cell is operated at 900° C in a dry, inert atmosphere with consumable anodes of titanium or hot-pressed titanium diboride (TiB2) powder. Agitation of the electrolyte is essential. Current densities may be 6 to 9 amperes per square decimeter (amp/dm2) with titanium anodes and 9 to 30 amp/dm2 with titanium diboride anodes. A current density of 6 amp/dm2 is equivalent to a plating rate of about 35 micrometers per hour. The adherence of the TiB2 deposit varies with the substrate material. It is most adherent on molybdenum and on 4130 steel that has been preplated with copper and nickel, less adherent on nickel, and still less adherent on Inconel and on 4130 steel without the preplate. Cathode and anode reactions are suggested.

Jan 1, 1976

By Willard L. Hunter

A series of steel heats, one low-alloy and nine carbon, was made by the Bureau of Mines in a 1-ton arc furnace from ferrous scrap from incinerated refuse, steel cans, and detinned steel cans, both alone and blended with heavy-melting scrap. Two additional control heats, one of carbon steel and one of low-alloy steel, were made from electric furnace heavy-melting scrap to pro-vide comparative data. The steel products were cast into two 4-by 4-inch nominal 50-pound ingots; in most heats, an 8-by 8-inch nominal 7S0-pound ingot was also obtained. Tests of these ingots indicated that reinforcing bars of acceptable quality can be made from urban refuse components such as steel cans.

Jan 1, 1976

By James J. Snodgrass

The Bureau of Mines designed and constructed a series of calibration models for geophysical borehole logging. A nominal hole diameter of 3 inches was selected as representative of typical core holes drilled for mining and engineering purposes, although additional hole diameters of 2, 5, and 8 inches are provided in one of the models for determination of empirical correction factors for variations in hole diameter. The physical properties of the models were determined by laboratory analyses of drill core samples and evaluated statistically for reliability. This report outlines the location of the models, elements of design and construction, and results of the laboratory tests. The models are available at the Denver Federal Center, Denver, Colo., for use by Government agencies and private industry to calibrate logging equipment for measurements of density, sonic velocity, magnetic susceptibility, and electrical resistivity.

Jan 1, 1976

By J. E. Pahlman

The Bureau of Mines performed research on a fluid-bed magnetic roasting process for nonmagnetic taconites that utilizes low-rank coals and lignites as reductants and fuels. Roasting tests on a Michigan nonmagnetic taconite were conducted at 600° to 725° C with lignite or subbituminous coal as reductants. Partial combustion of the reductant reduced the amount of heat externally applied to the reactor to maintain the desired reactor temperature. Cleaned, dried reactor top gases were recycled to recover a portion of the reducing potential in these gases without adversely affecting concentrate grade and iron recovery. Highest iron recoveries for magnetic concentrates were obtained at a roast temperature of 650° C with lignite and at a roast temperature of 725° C with subbituminous coal. Magnetic concentrates were obtained that were comparable with commercial concentrates.

Jan 1, 1976

By Jack E. Fraley

Magnesium oxysulfate cement has been specially formulated as a sealant in underground coal mines for reducing sloughing of shale roofs and coal ribs, for reducing air losses through block stoppings, for constructing sprayed stop-pings over approved jute cloth or metal lath, and for reducing combustibility of polyurethane foam. A standard spray machine (Mining Enforcement and Safety Administration (MESA) approved) was used for the underground testing. Our research shows that a 1/2-inch coating reduces shale and coal sloughing, reduces air losses through block stoppings, and prevents fire propagation through a metal tunnel lined with polyurethane foam. During the underground tests, excess mixing water was used to improve pumping the slurry to the spray nozzle. This was later found to increase shrinkage cracks in the cured coatings. Controlling excess water is important to an acceptable coating.

Jan 1, 1976